Kenwood DVR-6100-K Service manual

DVD / AV RECEIVER

MENU

STOP PLAY/PAUSE

INPUT

76

0

ON SCREENVOLUME

OPEN/CLOSE

POWER

-ON/–OFFSTANDBY

ACTIVE EQ

ENTER

MIC LEVEL

CS II

TOP MENU/BAND

DSP

PRO LOGIC IIDOLBY DIGITAL

DTS

PHONES

(OPTICAL)

VIDEO AUDIO RL

FRONT AUX

DIGITAL

70%

DVR-6100/6100K

SERVICE MANUAL

(DVT-6100)

note: This manual is not available for U.S.A and canada market.

DEC cabinet *
(B07-)

DEC button
(K29-8250-08)

DEC button
(K29-8251-08)

DEC crystal
(B10-3900-08)

MLD indicator
(B10-3897-08)

DEC knob
(K29-8249-08)

© 2002-7 PRINTED IN KOREA
B51-5803-00 (K/K) 2196

DEC button
(K29-8253-08)

DEC button
(K29-8255-08)

DEC button
(K29-8256-08)

DEC button
(K29-8254-08)

IC-opt
(W02-2961-08)

Phone jack
(E11-0957-08)

Pun cover
(A01-3863-08)

Conn-speaker
(E70-0165-08)

Tuner ass'y *
(W02-)

Con phono socket
(E63-1270-08)

D-REM
(W02-2911-08)

Con phono socket
(E63-121-08)

In compliance with Federal Regulations, following are repro­duction of labels on, or inside the product relating to laser
product safety.

Caution : No connection of ground line if disassemble

the unit. Please connect the ground line on

rear panel, PCBs, Chassis and some others.

Con phono socket
(E63-1244-08)

Con phono socket
(E63-1289-08)

Con DIN socket
(E63-1243-08)

KENWOOD Corp. certifies this equipment conforms to DHHS
Regulations No.21 CFR 1040. 10, Chapter 1, subchapter J.

DANGER : Laser radiation when open and interlock defeated.
AVOID DIRECT EXPOSURE TO BEAM.

Con phono socket
(E63-1290-08)

Illustration is DVR-6100K.

* Refer to parts list on page 37.

Wire-MCRDM *
(E30-)

MLD clamp
(J42-0350-08)

*AC Plug Adaptor (1) *

(E03-0115-05)

Use to adapt the plug on the
power cord to the shape of the
wall outlet.
(Accessory only for regions where
use is necessary.)

FM indoor antenna (1)

Loop antenna (1)

Remote control unit (1)

Batteries (R6/AA) (2)

V ideo cord (1)

SCART plug adaptor (1)
(Europe and U.K. only)
(E69-0012-05)

Speaker cords (6)

(T90-0882-08)

(A70-1607-08): KP
(A70-1608-08): YX
(A70-1609-08): ET
(A70-1610-08): MM2H

(E30-7265-08): RED
(E30-7283-08): GREEN
(E30-7284-08): BLUE
(E30-7285-08): VIOLET
(E30-7269-08): GREY
(E30-7286-08): WHITE

(T90-0896-08)

(E30-1427-05)

Caution on condensation

Condensation (of dew) may occur inside the unit when there is
a great difference in temperature between this unit and the out­side.
This unit may not function properly if condensation occurs. In
this case, leave the unit for a few hours, and restart the opera­tion after the condensation has dried up.

Be specially cautious against condensation in a fol­lowing circumstances:

When this unit is carried from one place to another across a large
difference in temperature, when the humidity in the room where
this unit is installed increases, etc.

Stored contents which are
cleared in at least a week after
power plug is unplugged from
power outlet.

Amplifier section

Last input selection
Volume control value
Surround setting
ACTIVE EQ

Tuner section

Receiving band
Frequency
Preset stations
Tuning mode setting

DVD section

Menu setup

Power status

Memory backup function

WARNING NOTICE:

IN MOST CASES IT IS AN INFRINGEMENT OF COPY­RIGHT TO MAKE COPIES OF TAPES OR DISCS WITH­OUT THE PERMISSION OF THE COPYRIGHT OWN­ERS. ANYONE WISHING TO COPY COMMERCIALLY
AVAILABLE TAPES OR DISC SHOULD CONTACT THE
MECHANICAL COPYRIGHT PROTECTION SOCIETY
LIMITED OR THE PERFORMING RIGHTS SOCIETY LIM­ITED.

Note related to transportation and movement

Before transporting or moving this unit, carry out the
following operations.

1 Remove the disc from the unit.
2 Press the 6 key.

3 Wait a few seconds and turn the unit OFF.

Operation to reset

The microcomputer may fall into malfunction (impossibility
to operate, erroneous display, etc.) when the power cord is
unplugged while power is ON or due to an external factor. In
this case, execute the following procedure to reset the
microcomputer and return it to normal condition.

÷ Please note that resetting the microcomputer clears the

contents stored in and returns and to condition when it left
the factory.

Set the POWER switch to ON (set to Standby mode).
Then press the ¢ key, 4 key and STOP key in this
order.

The marking this product has been classified as Class

1. It means that there is no danger of hazardous radia­tion outside the product.
Location: Back panel

CLASS 1

LASER PRODUCT

The marking of products using lasers

(Except for some areas)

DVR-6100/6100K

CONTENTS / ACCESSORIES / CAUTIONS

Contents

CONTENTS / ACCESSORIES / CAUTIONS............. 2

DISASSEMBLY FOR REPAIR....................................3

BLOCK DIAGRAM ......................................................4

CIRCUIT DESCRIPTION ............................................5

WIRING DIAGRAM ...................................................14

Accessories

PC BOARD .............................................................. 15

SCHEMATIC DIAGRAM .......................................... 24

EXPLODED VIEW ....................................................36

PARTS LIST..............................................................37

SPECIFICATIONS ......................................Back cover

Cautions

2

DISASSEMBLY FOR REPAIR

How to open the tray if it does not come out.

1. Insert a flat driver in the drawing through the hole on the load­ing chassis bottom and pull the lever down.

2. Pull out the tray frontward by hand when it comes just out.

DVR-6100/6100K

SYSTEM CONFIGURATION

SYSTEM RECEIVER SPEAKERS SUB WOOFER DESTINATIONS
DVT-6100 DVR-6100 KSW-6100 - E,T,X,Y,M
DVT-6100K DVR-6100K KSW-6100 - M,H
DVT-6100K DVR-6100K KSW-6100 - M2(UAE)

3

D GND

6dB

6dB

C-VIDEO

DVD

S-VIDEO

6dB

6dB

DVD

AGND

-5.6V

+5.6V

COMPOSITE

R(CR)

B(CB)

G(Y)

C

Y

+5.6V

-5.6V

AGND

R(CR)

B(CB)

G(Y)

C

Y

CVBS

FROM SYSTEM u-COM

27MHz

DAC MCLK

MIC IN

MGND

DGND

+5.6V

SPDIF

DGND

MGND

+5VA

AGND

+12VA

-5VA

+3.5V

+2.5V

+5V

+5.5VS

+9VM

+12VM

to
DVD & VIDEO

GND

P/C

5.5VS

P/D

to FRONT

LPF

LPF

LPF

LPF

LPF

LPF

INPUT

12.28MHz

SDATAN1

SW

CT

SR

SL

FR

FL

DVD

FROM SYSTEM u-COM

SW

CT

SR

FR

SL

FL

SW

CT

SR

SL

FR

FL

CHGND

AM OSCFM OSC

22 4

DGND

AGND

TUNER-L

TUNER-R

to u-COM

AGND

BUFFER

RDS DATA/CLK

GND

GND

8

4

5

7

1

2

3

1

2

3

1

2

F201

SK21

ST-BY +5V

AC INPUT FOR SMPS

AC2AC1

+

VEE

VDD

+

FL AC

FL AC

FUNCTION SECTION CONTROLSECTION

VOLUME/TONETUNER DVD

CONTROL

LED

CE,CLK,DATA

4094

+5V

A/D INPUT

P/C

RDS DATA/CLK

POWER DOWN

TO SMPS

DETECT

DC

PROTECT

DGND

HEADPHONE

DETECT

H/P MUTE

17dB

C/S

MUTE

SUB WOOFER

W/F

MUTE

-29.5V

29.5V

MIC DET

++

-27V

FL

+

6

DC PROTECTION

S/W

CENTER

S/W

GND

SR

SL

FR

GND

FL

1

5

3

2

4

15324

12 534

12

F252

1

5

3

2

4

230V 115V

GND

GND

GND

+3.3V

+5V

+15V

-15V

AV AUX(FRONT)

SAT/CABLE

VCR OUT

VCR IN

MONITOR

MONITOR

VIDEO
SWITCHING

IC61

MPEG
PROCESSOR

SDRAM

FLASH

EEPROM

ADC

MECHANISM

CONTROL

LOAD

PLL IC

DAC

AUDIO-

IC64

SECTION

DVD

SMPS FOR
DVD & VIDEO

FOR DVD

AC INPUT

AUX(F)

SAT/

OPTICAL

OPTICAL

OUTPUT

DIGITAL INPUT

(OPTICAL)

DIR

AUDIO

DIGITAL

ADC &
DAC

IC33 IC31IC39

IC37,38

IC11

VOLUME &

MASTER

TONE
CIRCUIT

IC15-B

IC15-A

IC16-B

IC16-A

IC17-B

IC17-A

GND

AM

FM75

ANTENNA

AM RF

FRONT-END

FM

IF AMP

FM/AM

DECODER

RDS

IF+MPX

PLL

TUNER MODULE

VCR IN

VCR OUT

AUX/FRONT

SAT/CABLE

IC14

IC13

AUDIO
SWITCH

N112

N111 P2

AC INPUT

STAND -BY
CONTROL

Q251

D22

IC51

SYSTEM u-COM

HNV-11SM18

FL DISPLAY

IC81

REGISTER

SHIFT

FRONT KEY
FUNCTION

NJ83

PROTECTION

Q24,25

HEAD­PHONE

IC12

HEADPHONE
AMP

VIDEO INPUT

Q30,31

REC OUT

DIGITAL
IN

DATA DATA

DIGITAL
DATA

CABLE

PROCESSOR

DIGITAL
OUT

(ASSY)

MIC JACK

IC82

MIC AMP

(M) TYPE ONLY

IC34-B

IC34-A

IC36-B

IC36-A

IC35-B

IC35-A

Q23

IC23

+15V

D30

D29

D28

D27

-15V

IC24

+3.3V

IC25

D24

D23

IC26

+5.0V

IC21

IC20

IC19

IC18

NJ11-C

NJ11-B

NJ11-A

IC22

SPKR
RLYSK13

RLYSK12

SPKR

SPKR
RLYSK11

N251 P2

N252P252

(M,M2,Y) TYPE ONLY

LOOP

S-VIDEO

NJ34

NJ35

OUTOUT

PRE
AMP

P251

SURROUND
DSP B'D

4

BLOCK DIAGRAM

DVR-6100/6100K

DVR-6100/6100K

CIRCUIT DESCRIPTION

1. Pin Description of MPEG Processor IC (DVD Part IC61)

Pin No. Pin Name I/O Pin Description

PIOs and communication

1 PIO2(5) RGB SEL(BLANK) I/O RGB sel (blank). unused
2 PIO2(6) VIDEO MUTE I/O Video mute control.
3 PIO2(7) 16: 9 INDICATOR I/O 16 : 9 indicator (unused).
6 PIO3(0) SCART H (TV/AUX) I/O Unused.
7 PIO3(1) I/O Unused.
8 PIO3(2) O CSB

✽

✽

9 PIO3(3) O SDIN
10 PIO3(4) IR REMOCON I/O Unused.
11 PIO3(5) O SCLK
12 PIO3(6) I/O Unused.
13 PIO3(7) DVD RESET I/O Power- on reset of front-end module.

Front-end

16 B DATA I I2S Data
17 B BCLK I I2S Bit clock
18 B FLAG I I2S Error flag
19 B SYNC I/O I2S Sector / ABS time

Reserved

20 B WCLK I/O Unused.
21 B V4 I/O Unused.
22 NRSS OUT I/O Unused.
23 VDD RGB - Supply voltage for RGB (+3.3VA).
24 VSS RGB - GND

Video DAC

25,26,27 B/G/R (OUT) O B/G/R signal outputs.

28 V REF RG I Reference voltage input for DAC RGB.
29 I REF RG I Reference current input for DAC RGB.
30 VDD YCC - Supply voltage for YCC (+3.3VA).
31 VSS YCC - GND

32~34 Y/C/CV (OUT) O Y/C/CV signal outputs.

35 V REF YCC I Reference voltage input for DAC YCC.
36 I REF YCC I Reference current input for DAC YCC.

PIOs and communication

39 PIO4(0)HP MUTE - Unused.
40 PIO4(1) - Unused.
41 PIO4(2) O DAC system clock output.
42 PIO4(3) DAC RESET O DAC reset output.
43 PIO4(4) PLL CS O DAC mute control.
44 PIO4(5) DAC CLOCK O DAC clock output
45 PIO4(6) DAC DATA O DAC data output.
46 PIO4(7) DAC CS O DAC chip select.

Audio DAC

48 VDD PCM - Supply voltage for PCM (+3V3).
49 VSS PCM - Ground for PCM.
51 DAC SCLK (BCK) O DAC over sampling clock.
52 DAC PCMOUT0 (DATA) O DAC PCM data out 0.
53 DAC PCMOUT1 O DAC PCM out 1 (unused).
54 DAC PCMOUT2 O DAC PCM out 2 (unused).
55 DAC PCMCLK O DAC PCM clock.
56 DAC LRCLK O DAC PCM Left/Right clock.
57 SPDIF OUT O Audio digital data output.

Shared memory interface

58~63 SMI ADR(4~9) O SDRAM address bus.
66~69 SMI ADR(3~0) O SDRAM address bus.

5

DVR-6100/6100K

CIRCUIT DESCRIPTION

Pin No. Pin Name I/O Pin Description

70~73 SMI ADR(10~13) O SDRAM address bus.

74 SMI CS(0) O Chip select bank 0.
75 SMI CS(1) - Unused.
76 SMI RAS O SDRAM RAS
77 SMI CAS O SDRAM CAS
78 SMI WE O SDRAM write enable.
79 SMI DQML O DQ MASK enable low.
80 SMI DQMU O DQ MASK enable up.
82 SMI CLKIN I SDRAM clock input.

84~93 SMI DATA(0~9) I/O SDRAM data bus.

95 SMI CLKOUT O SDRAM clock out.

97~102 SMI DATA(10~15) I/O SDRAM data bus.

Reserved

✽

✽

✽

✽

103 ADC SCLK I/O ADC digital audio port clock.
104 ADC LRCLK I/O ADCsample rate clock.
105 ADC DATA I ADC digital audio data input.
106 ADC PCMCLK O Crystal input or master clock input.

JTAG

109 TRST I Test reset from emulator module.
110 TMS I Test mode select.
111 TDO O Test data out to emulator module.
112 TDI I Test data input from emulator module.
113 TCK I Test clock input from emulator module.

Timers

114 PWM2 I/O Unused.
115 PWM1 I/O ROM boot option port (voltage low = emulator booting).
116 PWM0 I/O Unused.

EMI Interface

117 CPU OE I/O Flash ROM output enable
118 CPU PRO CLK O SDRAM clock (unused).

Clock & Reset

120 PIX CLK I 27MHz main clock input.
122 VDD PLL - Supply voltage for PLL (+3V3).
123 VSS PLL - Ground for PLL.
124 RESET I Chip reset input.

Interrupt

125 IRQ(2) I Interrupt request 2 from front-end module.
126 IRQ(1) I Unused.
127 IRQ(0) I Unused.

EMI Interface

128 CPU BE(0) O BYTE 0 Enable
129 CPU BE(1) O BYTE 1 Enable
130 CPU RW O Unused.
131 CPU WAIT I Wait state (connected to ground).
132 CPU CE(3) O Flash ROM chip select.
133 CPU CE(2) O Flash ROM down-load JIG module select.
134 CPU CE(1) O Unused
135 CPU CE(0) O Unused.
138 CPU RAS1 I/O Unused.
139 CPU CAS0 O Unused.

140 CPU CAS1 O Unused.
141~148 CPU DATA(0~7) I/O Flash ROM data input/output (0~7).
151~158 CPU DATA(8~15) I/O Flash ROM data input/output (8~15).
161~170 CPU ADR(1~10) O Flash ROM address (1~10).
173~183 CPU ADR(11~21) O Flash ROM address (11~21).

6

DVR-6100/6100K

CIRCUIT DESCRIPTION

Pin No. Pin Name I/O Pin Description

PIOs and communication

186 PIO0(0) T STROBE I/O UART0 data
187 PIO0(1) MOD SW I/O ATAPI RD
188 PIO0(2) O Unused.
189 PIO0(3) O Unused.
190 PIO0(4) O Unused.
191 PIO0(5) I Unused.

192

193

194 PIO1(0) SDA I/O SSC0 data (MTSR out / MRST in)
195 PIO1(1) SCL I/O SSC0 clock

196

197 PIO1(3) TXD(JIG) I/O UART2 TXD
200 PIO1(4) RXD(JIG) I/O UART2 RXD
201 PIO1(5) FRONT TXDI I/O UART1 TXD
202 TRIGGER IN I/O Trigger input from JIG.
203 TRIGGER OUT I/O Trigger output from JIG.
204 PIO2(0) H/P - Unused.
205 PIO2(1) FRONT RXD I/O UART1 RXD
206 PIO2(2) I Unused.
207 PIO2(3) - Unused.
208 PIO2(4) AUDIO MUTE O Audio mute control.

Power supply

4,47,81,107

136,159,184

14,37,64,94

119,149,171 VDD2 5 - 2.5V Power supply.

198

5,15,38,50,65

83,96,108,121

137,150,160
172,185,199

✽ M Type only

PIO0(6) SLIDER SENSOR
OPEN/CLOSE (DRAWER POSITION)
PIO0(7) SLIDER IN
(DRAWER CCW/CTRL)

PIO1(2) SLIDER OUT
(DRAWER CW CTRL)

VDD3 3 - 3.3V Power supply.

VSS - GND

I/O Detection port of slider sensor for DVD mechanism.

I/O Control port of slider (IN) for DVD mechanism.

I/O Control port of slider (OUT) for DVD mechanism.

2. Pin Description of System Microcomputer : CXP82860(Microprocessor IC51)

Pin No. Pin Name I/O Description

1 GRID2 O FIP Grid output.
2 GRID1 O FIP Grid output.
3 NC - Connected to VDD.
4 POWER DOWN I Power down check.
5 RDS CLK I RDS clock input.
6 DVD RX I DVD UART interface (RX).
7 RDS OPTION - Unused.
8 RMC I Remote controller signal input.

9 RDS DATA I RDS data input.
10 SM7346 CLK O Volume IC (IC11) clock output.
11 SM7346 DATA O Volume IC (IC11) data output.
12 ENCODER UP I Encoder (1) signal input.
13 ENCODER DW I Encoder (2) signal input.
14 DVD TX O DVD UARTinterface (TX).
15 DVD RST O DVD reset signal output.

7

DVR-6100/6100K

CIRCUIT DESCRIPTION

Pin No. Pin Name I/O Description

16 DSP A. BOOST O DSP auto boot.
17 H/P CHK I Detection pin of headphones jack.
18 CS8415A-CE O DIR IC (IC39) chip enable.
19 EMPHASIS O CS4228 DAC IC emphasis ON/OFF
20 TUNED I Tuned signal input for tuner.
21 DSP INTREQ O DSP INT request.
22 4094CE O 4049 (IC81)chip enable.
23 CS49326 CE O CS49326 DSP IC (IC33) chip enable.
24 CS4228 CE O CS4228 DAC IC (IC31) chip enable.
25 DSP CLK O CS49326 DSP IC (IC33) clock output.
26 CS49326 DATA IN I CS49326 DSP IC (IC33) data input.
27 DSP DA OUT O CS49326 DSP IC (IC33) data output.
28 VREF I A/D reference voltage input.
29 PROTECT I AMP protection input.
30 KEY IN I A/D key input.
31 EEPROM DATA I/O EEPROM (IC52) data output.
32 KEY2 IN I A/D key input.
33 8415 DA IN I CS8415 DIR IC (IC39) data input.
34 DVD OPTION I Setting pin for the destination.
35 PLL DATA IN I PLL data input.
36 STEP OPTION I Setting pin for tuner destination.
37 VSS(G) I Analog ground.
38 RST I Reset signal input.
39 EXTAL I Crystal resonator (10MHz) connection.
40 XTAL O Crystal resonator (10MHz) connection.
41 GND - Digital ground.
42 NC O Unused.
43 GND - GND
44 VDD I Digital ground.
45 VFDP I Power supply for VFDP.
46 STANDBY O Control pin for power relay on/off.
47 SPK RELAY O Control pin for speaker relay on/off.
48 SUB ON/OFF O Gain control for sub woofer.
49 CS8415 RST O CS8415 (IC39) reset signal output.
50 PLL CE O PLL chip enable.
51 PLL CLK O PLL clock output.
52 PLL D OUT O PLL data output.
53 A CLK O Common clock (LC7821,BU4094) output.
54 A DATA O Common data (LC7821,BU4094) output.
55 EEPROM CLK O EEPROM (IC52) clock output.

56~59 VIDEO (SW1~SW4) O Control pin for video.

60 4228 RST O CS4228 (IC31) reset signal output.
61 LC7821 CE O LC7821(tuner pack) chip enable.
62 SM7346 CE O Volume IC (Main IC11) chip enable.
63 T MUTE O Tuner mute control.
64 S MUTE O Mute control pin for surround signal
65 C MUTE O Mute control pin for center signal.
66 F MUTE O Mute control pin for front signal.
67 W MUTE O Mute control pin for sub woofer signal.

68 CS49326 RST O CS49326 DSP IC (IC5) reset signal output.
69~71 DSP (A15~A17) O DSP ROM address (SEL 1~3).
72~88 SEG (1~17) O FIP segment output.

89 VDD - Digital power supply.

90,91 SEG18,19 O FIP segment output.

92-100 GRID (11~3) O FIP Grid output.

8

DVR-6100/6100K

CIRCUIT DESCRIPTION

3. Pin Description of IC’s

3-1 64 Bit SDRAM : HY57V641620HGT (DVD Part IC63)

Pin No. Pin Name I/O Description

38 CLK I

37 CKE -

19 CS - Enables or disables all inputs except CLK, CKE, and DQM.

20,21 BA0,BA1 -

22~26
29~35 Auto-precharge flag : A10

16,17,18 WE,CAS,RAS - WE, CAS and RAS define the operation.

15,39 LDQM,UDQM I/O Controls output buffers in read mode and masks input data in write mode.
2,4,5,7,8,10
11,13,42,44
45,47,48,50

51,53

1,3,9,14,27

43,49

6,12,28,41,

46,52,54

36,40 NC - Unused.

A0~A11 -

DQ0~DQ15 I/O Multiplexed data input/output pin.

VCC/VCC Q - Power supply for internal circuits and input buffers.

VSS/VSS Q - Ground terminal.

The system clock input. all other inputs are registered to the SDRAM on
the rising edge of CLK.
Controls internal clock signal and when deactivated, the SDRAM will be one
of the states among power down, suspend or self refresh.

Selects bank to be activated during RAS activity.
Selects bank to be read/written during CAS activity.
Row address : RA0~RA11, Column address : CA0~CA7

3-2 24-bit, 192kHz Stereo DAC : WM8728 (DVD Part IC64)

Pin No. Pin Name I/O Description

1 LRCIN I

2 DIN I

3 BCKIN I Audio data bit clock input.
4 MCLK I Master clock input.
5 ZERO O Infinite zero detect flag.
6 DGND - Digital ground supply.
7 DVDD - Digital positive supply.
8 VOUTR O Right channel DAC output.

9 AGND - Analog ground supply.
10 AVDD - Analog positive supply.
11 VOUTL O Left channel DAC output.
12 VMID O Mid rail decoupling point.
13 VREFN - DAC negative reference.
14 VREFP - DAC positive reference.

15 CSBIWL I

16 MODE I Control mode selection.
17 MUTEB - Mute control. "L" = Mute on, "H" = Mute off

18 SDIDEM -

19 SCKDSD I

20 LAT12S I

DAC sample rate clock input : PCM input mode
Right channel DSD bitstream input : DSD input mode
Serial audio data input : PCM input mode
Left channel DSD bitstream input : DSD input mode

Software mode : 3-wire serial control chip select
Hardware mode : Input word length

Software mode : 3 or 2-wire serial control data input
Hardware mode : De-Emphasis select
Software mode : 3 or 2-wire serial control clock input
Hardware mode : DSD bitstream operation select
Software mode : 3-wire serial control load input
Hardware mode : Input data format selection

9

CIRCUIT DESCRIPTION

BIAS

8 V02

7 PVCC

6 SVCC

5 VIN2

1GND

2VO1

3VCTL

4VIN1

TSD

LOGIC SWITCH

PRE DRIVER

DRIVER OUT

3-3 Flash Memory : SST39VF800A904 (DVD Part IC66)

Pin No. Pin Name I/O Description

1~8, 16~25,48 A0~A18 I Address Inputs

29,31,33,35,38,40

42,44

30,32,34,36,39,41,43 DQ8~DQ14 I/O Data Input/Outputs

45 DQ15 I/O Data Input/Outputs or Address input
26 CE - Chip Enable
28 QE - Output Enable
11 WE - Write Enable
12 RP - Reset/Block Temporary Unprotect
15 RY/BY O Ready/Busy/Output(Unused)
47 BYTE - Byte/Word Organization
37 VCC - Supply Voltage

27,46 VSS - Ground

3-4 HEX Inverter (Single Stage) : M74HCU04 (DVD Part IC67)

Pin No. Pin Name I/O Pin Description

1,3,5,9,

11,13

2,4,6,8,

10,12

7 GND - Ground

14 VCC - Positive Supply Voltage

A0 to A5 I Data Inputs

Q0 to Q5 O Data Outputs

DQ0~DQ7 I/O Data Input/Outputs, Command Inputs

DVR-6100/6100K

Truth Table

AQ
LH
HL

3-5 Video Driver : MM1540AF (DVD Part IC68)

Pin No. Pin Name I/O Description

1,28 VCC1,2 - VCC

2 VIN I Unused
3 YC MIX - YC MIX select (GND)
4 CIN I Croma input
5 CLP - Clamp select (Connected to VCC)

6,9 YIN (1,2) I Video input (Composite or Y)

7 MUTE 1 O Mute select (GND)
8 MUTE 2 O Mute select

10 GND - GND

11,13 CbIN, CrIN I Component input

12 Dual/Single - Power select (+5V)

14,15,19,

21,22,24

16,18,20,

23,25,27

17,26 PS2,PS1 - Power save (Connected to GND)

3-6 DC Motor Driver : FAN8082(DVD Part IC69)

Pin No. Pin Name I/O Pin Description

1 GND - Ground
2 VO1 O Output 1
3 VCTL I Motor speed control
4 VIN1 I Input 1
5 VIN2 I Input 2
6 SVCC - Supply voltage (Signal)
7 PVCC - Supply voltage (Power)
8 VO2 O Output 2

VEE1, VEE2 - VEE (-5V)

CrOUT, CbOUT,
YOUT2,YOUT1,

COUT,VOUT

O Video output

Internal Block Diagram

10

DVR-6100/6100K

CIRCUIT DESCRIPTION

3-7 Stereo Audio ADC : VM8739 (DVD Part IC70) M Type only

Pin No. Pin Name I/O Pin Description

1 SDIN I 3-wire MPU data input/2-wire MPU data input.
2 SCLK I 3-wire MPU clock input/2-wire MPU clock input.
3 XTI/MCLK I Crystal input or master clock input (MCLK).
4 XTO O Crystal output.
5 DCVDD - Digital core VDD.
6 DGND - Digital GND.
7 DBVDD - Digital buffers VDD.
8 BCLK I/O Digital audio port clock.

9,10 DNC - Unused.

11 ADCDAT O ADC digital audio data output.
12 ADCLRC I/O ADC sample rate clock.
13 NC - Unused.
14 AVDD - Analog VDD.
15 AGND - Analog GND.
16 VMID O Mid-rail reference decoupling point.
17 R IN I Right channel line input (AC coupled).
18 L IN I Left channel line input (AC coupled).
19 MODE I Control interface selection, pull up (on power up only).
20 CSB I 3-wire MPU chip select/2-wire MPU interface address selection.

3-8 Volume Control IC: M62446AFP (Main B' D IC11)

Pin No. Pin Name I/O Pin Description

1~4 OUT(4~1) O Unused.

5 AVDD - Power supply (+7.0V) for analog.
6 SWin I Volume input for SW channel.

7,10,12,14 GND(S,C,R,L) - Analog ground.

8 SRin I Volume input for SR channel.

9 SLin I Volume input for SL channel.
11 Cin I Volume input for center channel.
13 Rin I Tone input for FR channel.
15 Lin I Tone input for FL channel.

16,17 BYPASS(R,L) I Input pin of the volume input selector when bypass.
18,25 LTRE/RTRE - Frequency characteristic setting pin in the tone control (Treble).

19,24,20,

23,21,22

26,28 CR2/CL2 O Tone output.
27,29 CR1/CL1 I Input pin of the main volume.

30 AVSS - Power supply (-7.0V) for analog.
31 L OUT O Output pin of the main volume.
32 R OUT O Output pin of the main volume.

33~36 C/SL/SR/SW(OUT) O Output pin of the main volume.

37 AGND - Analog ground.
38 DGND - Digital ground.
39 LATCH I Latch input.
40 DATA I Input pin of the serial data.
41 CLK I Clock input.
42 DVDD - Power supply (+5.0V) for digital.

LBASS3/RBASS3
LBASS2/RBASS2 - Frequency characteristic setting pin in the tone control (Bass).
LBASS1/RBASS1

11