Kenwood DPF-1030, DPF-1030-E, DPF-1030-S, DPF-2030, DPF-2030-E Service manual
...
COMPACT DISC PLAYER
70%
POWER
- ON – OFF
PHONES
P.MODE
EDIT
CHECK
CLEAR
PEAK SEARCH
TIME DISPLAY
OPEN/CLOSE
REPEAT RANDOM
0
76
4¢
1¡
OUTPUT
OPTICAL
DIGITAL
OUTPUT
SYSTEM CONTROL
L
R
TEXT
DPF-1030/1030E/1030-S
DPF-2030/2030E/2030-S
SERVICE MANUAL
Power Knob *
(K29-)
H/P jack
(E11-0345-08)
Tray cover *
(A21-)
FL window
(B10-3611-08)
© 2000-3/B51-5603-00 (K/K) 2100
Front cab ass'y *
(A60-)
Top cabinet *
(A01-)
Digital output jack
(W02-2752-08)
Pin jack
(E63-1081-08)
In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser
product safety.
Refer to DP-3080MKΙΙ/3090 Service manual (B51-5349-00),
if you require disassembly for repair.
System jack
(E11-0188-05)
AC power cord bushing
(J42-0083-05)
KENWOOD-Corp. certifies this equipment conforms to DHHS
Regulations No. 21 CFR 1040. 10, Chapter 1, Subchapter J.
DANGER : Laser radiation when open and interlock defeated.
AVOID DIRECT EXPOSURE TO BEAM.
* Refer to parts list on page 14.
AC power cord *
(E30-)
DPF-1030/2030
Audio
(E30-2913-08)
(A70-1414-08) : RC-P0715
(DPF-2030 only)
Battery cover : (A09-1190-08)
(E30-2912-08)
cord .................. (1) System control cord ...... (1)
Remote control unit ......... (1)
Batteries
(DPF-2030 only)
(R6/AA)........ (2)
AC
(E03-0115-05)
plug adaptor .............. (1)
Use to adapt the plug on the
power cord to the shape of the
wall outlet.
(Accessory only for regions where
use is necessary.)
TIME DISP
123
P.MODE
456
EDIT
789
CLEAR
RANDOM
REPEAT
OUTPUT LEVEL
DOWN UP
CHECK
0 +10
76
4¡1¢
REMOTE CONTROL UNIT RC-P0715
CONTENTS / ACCESSORIES
Contents
CONTENTS / ACCESSORIES .................................. 2
DISASSEMBLY FOR REPAIR....................................2
CIRCUIT DESCRIPTION............................................3
ADJUSTMENT............................................................4
PC BOARD ................................................................ 5
Accessories
SCHEMATIC DIAGRAM............................................ 7
EXPLODED VIEW ....................................................12
PARTS LIST..............................................................14
SPECIFICATIONS ......................................Back cover
DISASSEMBLY FOR REPAIR
1. How to open tray when tray not come out.
1. Insert the screw driver to left side hole of mechanism ass'y.
2. While pushing the rack gear fully right wards, then the tray pull.
2
Pin No. Pin Name I/O Description
1-6 6G-1G O FL grid control port.
7 NC - Unused.
8 VDD - Power supply(+5V).
9-11 - - Connected to ground.
12 C-RESET O DSP signal output.
13 S-MUTE O Muting signal output for system.
14 NC - Unused.
15 TEXT I Text copy detection.
16 - - Connected to ground.
17 RESET I Hardware reset signal input.
18 LD CLOSE O Tray motor control.
19 LD OPEN O Tray motor control.
20 AVSS - Connected to ground.
21 - - Connected to ground.
22 PU IN SW I Pickup location.
23 OPEN SW I Tray open switch input.
24 CLOSE SW I Tray close switch input.
25-28 KEYO-3 I Key input port.
29 AVDD - Power supply(+5V).
30 AVREF - Reference voltage(+5V).
31,32 XT1,2 - Connected to ground.
33 VSS - Connected to ground.
34,35 XO,1 - X'tal 4.19MHz.
36 WRQ I Sub code Q output.
37 COIN O Command data to DSP.
38 16BIT - Unused.
39 HF - Connected to ground.
40 NC - Unused.
41 CQCK O Clock output to DSP.
42 SQOUT I SQ data to dsp.
43 RWC O Reading/writing control port.
44 GND - Connected to ground.
45 S BUSY I/O System control data.
46 S DATA I/O System control status.
47 RMC I Remote control signal input.
48 GND - Connected to ground.
49 TRY L/H O Tray motor speed control.
50 SL- O Sled motor control port(reverse).
51 SL+ O Sled motor control port(forward).
52 VDD - Power supply(+5V).
53-59 NC - Unused.
60 DRF I CD focus OK signal input.
61 NC - Unused.
62-70 a-j O FL segment(a-j) control port.
71 VLOAD - Power supply(-30V).
72,73 k,l O FL segment(k,l) control port.
74-77 NC - Unused.
78-80 9G-7G O FL grid(9G-7G) control port.
STOP key enable
If key in STOP,
return to start
stage.
START
FL LIGHT UP ALL
Tray open/close enable (display no change)
For move Pick-up, UP and DOWN key enable only stop mode
Key in PLAY
Laser ON , Display [LD ON]
Key in Play
Focus ON, Display [FS ON]
Key in PLAY
PLAY (Track servo OFF) Display [Sb OFF]
Key in PLAY
Play (Track servo ON)
Key in STOP
STOP
WITH TIME DISPLAY
Setting the test mode
: While pressing the STOP key, press the POWER switch.
Test mode will be cancelled by pressing the
POWER switch key in the stop mode.
When play mode, UP key enable
but only track jump.
1. Pin description of microprocessor
3
2. Test mode
CIRCUIT DESCRIPTION
DPF-1030/2030
3. Key function in test mode
No. INPUT KEY FUNCTION DISPLAY
1 PLAY(1ST) LASER ON LD ON
2 PLAY(2ND) FOCUSING SERVO ON FS ON
3 PLAY(3RD) PLAY(TRACKING SERVO OFF) Sb off
4 PLAY(4TH) PLAY(TRACKING SERVO ON) TN0. And Time
5 UP In the stop mode. Moves the pickup slightly
toward the outer position disc. –
When tracking servo is ON, set the track number up.
6 DOWN In the stop mode. Moves the pickup slightly
toward the inner position disc. –
When tracking servo is ON, set the track number up.
7 STOP Laser off, focusing servo off, tracking servo off. All segments
8 OPEN/CLOSE In the stop mode, Tray is opened or closed. All segments
DPF-1030/2030
Fig.4 Checking points
ADJUSTMENT
CD section
Since this CD system incorporates the following automatic
adjustment function, when the pickup is replaced, it is not necessary to readjust it
Since this CD unit does not need adjustment, the combination
of PWB and laser pickup unit is not restricted.
•Automatic adjustment item
1. Focus offset(Fig.1)
2. Tracking offset(Fig.2)
3. E/F balance (Tracking error balance) (Fig.3)
4. RF level AGC function (HF level : constant)
5. RF level automatic follow-up of the tracking gain
This automatic adjustment is performed each time a disc is
changed. Therefore, each disc is played back using the optimal
settings
4
Loading...