Kenwood DDX-8017, DDX-8027, DDX-8027-Y, DDX-8037, DDX-8047 Service manual

...

MONITOR WITH DVD RECEIVER

DDX8017/8037 DDX8027/8027Y DDX8047/8067

SERVICE MANUAL

Panel assy (A64-3576-01): DDX8017, (A64-3578-01): DDX8037 (A64-3577-01): DDX8027/8027Y (A64-3579-01): DDX8047, (A64-3580-01): DDX8067

Illustrations is DDX8017

Escutcheon (B07-3105-02)

EJECT FNC

AVOUT

SEL

SRC

PWROFF

VOL SEEK

Escutcheon (B07-3046-04)

Mounting hardware assy (J22-0171-03)

Remote controller (A70-2072-05 : RC-DV601)

MODE

SCRN

DIM

MONITOR WITH

DVD

RECEIVER

AUTO

Size AAA battery Not supplied

Cleaning cloth (W01-1620-05)

DDX8027/8027Y only DDX8017/8037/8047/8067 only

DC cord (E30-6477-15)

Antena adaptor (T90-0552-05)

DC cord (E30-6475-15)

DC cord (E30-6478-05)

Screw set (N99-1776-05)

This product uses Lead Free solder.

Lever (D10-4674-04) x2

DDX8017/8027/8027Y DDX8037/8047/8067

NOTES ON ASSEMBLING THE MECHANISM

1. Fasten Scre w A so that the interval (a) will be about 5.2mm and the interval (b) will be about 2.6mm. (The interval (a) can be measured using a pair of vernier calipers or similar tools.)

2. Turn B so that Position (c) will come at about the center of interval (d).

3. Then, play the test disc and fine tune A or B so that the jitter value would be minimized.

5.2mm

2.6mm

● Complete view

DDX8017/8027/8027Y DDX8037/8047/8067

BLOCK DIAGRAM

(X35- )

TOUCH

LCD

DVD MECHA

TILT MECHA

(X34- )

(X14- )

TOUCH CONTROL

INVERTER CIRCUIT

SRAM

SDRAM

FLASH

SDRAM

MOTOR DRIVER

MPEG DECODER

SH-3 u-COM

SYSCON SDRAM

CLOCK GENERATOR

FLASH

CPLD

AUDIO DAC

GRAPHIC

SPDIF

(X89- )

TIMING CONTROLLER

CHROMA GAMMA IC

RGB SW

VIDEO ENCODER

COMPOSITE SW

REMOTE CONTROL RECEIVER

TV I/F

COMPOSITERGB SW

NAVI I/F

BOX u-COM

AM/FM TUNER

COMPOSITE SW

I/F

LX-BUS I/F

DSP

8ch DAC

DIR

ADC

AUDIO INPUT SELECTOR

AUDIO OUTPUT

POWER AMP

AV OUTAV-IN

SP OUTI/F

SELECTOR

PRE OUT

DDX8017/8027/8027Y DDX8037/8047/8067

BLOCK DIAGRAM

● X14-955/956

to X16

2DIN ONLY 1DIN ONLY

to MECHA

/956)

from SYSCOM

LCD CONTROL

LCD CS LCD DATA LCD CLK

KEY CONTROL

KEY2 RESET SRC

EJECT REMO LED R,G,B

1DIN ONLY

IC852 IC850

SDRAM

D(15:0) A(19:1) A(22:1) D(15:0)

IC800

SYSCOM

SH CLK SH MREQ SH SREQ SH MDATA SH SDATA SH RESET SH CON SH STBY SH INI SH DACK GR INT GR REQ TOUCH

13.5MHz

TOUCH EN

2 FREQUENCY DIVIDING

IC640

CLOCK GENERATOR

27MHz

ATAPI I/F

to DVD MECHA

(X14-955

SH-3

A(12:4) D(31:0)

IC851

36.864MHz

27MHz

IC560

SDRAM

SYSCOM

BE RST BE CLK BE MREQ BE SREQ BE MDATA BE SDATA

RL M+ RL M- EX M-

IC107

MOTOR DRIVER

TMOTOR M TMOTOR P

IC106

MOTOR DRIVER

SMOTOR M SMOTOR P

1DIN ONLY

FROM

A(24:1) D(31:0)

SRAM

IC601 IC652

MPEG DECODER

X'TAL 27MHz

A(11:1) D(15:0)

A(21:0) D(7:0)

IC520

FLASH

EX M+

IC700

1.5 FREQUENCY DIVIDING

DCLK 9.6MHz

GRAPHIC

MA(13:0) MD(15:0)

MA(13:0) MD(31:16)

CCIR601(7:0)

VCLOCK

HSYNC VSYNC

LA17 LA(1:0)

LD(3:0)

PLL ON

PLL CLK

IC237

GRAPHIC RGB

G-HD

G-VD

CDE

IC750

SDRAM

IC751

SDRAM

IC470

CPLD

RGB

POLS

VCOM

CHROMA GAMMA IC

VIDEO ENCODER

SPDIF

DATA1 BCLK LRCLK MCLK

1DIN ONLY

27MHz

to SYSCOM

ACC DET REV DET PRK DET ILLUMI REMO

to X35

1DIN ONLY

2DIN ONLY

IC101

E2PROM

from SYSCOM

HPOSI1,2,3,4, NTSC PAL PWM MIRROR LCD PON

IC105

RESET IC

IC104

IC239

1H DELAY

R-Y

to SH3

to SYSCOM

XDATA

BLK

VSY

T/C VD

T/C HD

4.43MHz

3.58MHz

B-Y

HSY

VMUTE

SW D MODE1,2,3

YDATA

AUTO DIMMER

PH DET

R SENS

SW A,B,C KEY1 OPEN/CLOSE KEY3 KEY4 SRC REMO EJECT

SCL SDA

D-FF

DELAY

NAVIL

NTSC PAL

COMPOSITE

RGB

DVDRGB DVDCOMP V DVDCOMP V

SYNC SEPA

IC650

LPF+6dB AMP +DRIVER+MUTE

MUTE

IC830

HD VD

IC240

RGB SW

DVDRGB

RGB SW VIDEO

IC654

VIDEO SW

2DIN ONLY

REG

BUFFER

MUTE

BU3.3V

MPU

SRAM

REG REG REG REG REG REG

+B ACC GCD

IC402

ADACML ADACMC ADACMD ADACRST

2ch AUDIO DAC

+14.4V

PON

+14.4V

PON

+14.4V

PON SW3.3V

POWER SUPPLY

DC/DC

+8.5V

TRANCE

+7.5V

IC400

LPF

1DIN ONLY

OPT DRIVER

+14.4V

-7V+7V

SYSCOM

SW5V

V5V

MECHA5V

SW2V

1.9V

1.8V

2DIN ONLY to SUB PANEL

LED R LED G

to ROM WRITER

RESET M CLK M DATA S DATA FROM VPP

to BOX MCU

M CLK M REQ S REQ M DATA S DATA SYS ON

2DIN ONLY

+B ACC GCD

TV/NAVI RG

DOWNMIX AUDIO

OPT OUT

to X34

POWER SUPPLY

CONNECTOR

LX I/F

NV I/F

to TV TUN

to X14

ISO AMP

IC500

ISO AMP

IC405

IC413

AUDIO

IC414

SEL

AUDIO

R SW

IC400-402

G SW B SW

SEL

VIDEO

IC416

VIDEO SEL

IC406

IC415

SEL

VIDEO

6dB AMP

VIDEO SEL

IC408

75 DRIVER

DRIVER

6dB AMP

VIDEO SEL 75

IC407

SEL

VIDEO

IC404

FM AM F/E

FST

BUFF

RDS

IC251

DECODER

ADJUST

LEVEL

MUTE

ADJUST

LEVEL

MUTE

ADJUST

LEVEL

IC151

ADJUST

LEVEL

TONE EQ

ADC(2ch)

IC7

MUTE

DIR SEL

IC10

DSP

IC9

S/P DIF

DAC(8ch)

IC6

BASS MANAGEMENT

IC12

LPF

IC2-4

POWER AMP

IC100

MUTE AMP

IC200-202 PRE OUT

AV OUT

MUTE

AV IN1

ISO AMP

IC204

AV IN2

ISO AMP

IC203

R-CAM

SEP

IC403

SYNC

MCU

IC303

REG

DC/DC

REG

DC 8PIN

LX CON

LX CLK LX DATA M LX DATA S

LX REQ S

LX MUTE

LX RST

LX REQ M

AUD Lch

AUD Rch

A GND

REMO

SYNC

A GND

AUD Lch

AUD Rch

TV DATA M TV DATA S

TV REQ S

TV REQ M

COMP V

M RST

R G

TV CLK

TV CON

TV Rch

A GND

TV Lch

COMP V

DVD Rch

DVD Lch

A GND

M REQ S

M REQ M

M DATA S

M DATA M

M RST

M CLK

M CON

REMO

MCU

DVD COMP

MCU

RDDA RDCL

QUAL

MPX for RDS

MCU

S-METER

IF COUNT

SDA

SCL

RDS MUTE

QUALITY

MCU

PON AM

A OUT

MCU

ACIN0 (FRONT)

ACIN1 (REAR)

FRONT

HPF (FRONT) (FRONT)

MUTE VOL

(FRONT)

(SUB-W)

ACIN2R

ACIN2L (CENTER)

MUTE (REAR)

REAR

(REAR)

HPF VOL

(REAR)

SUB

MAIN 2ZONE

2ZONE

(CEN

MUTE

/NF L

(NF)

LPF

VOLCENTER

SUB-W SUB) SUB)

(CEN

(FRONT)

PAOUT0

(REAR)

PAOUT1

LDOUT1 (REAR)

LDOUT0 (FRONT)

(CEN/NF)

LDOUT2L

(SUB/NF)

LDOUT2R

OUTPUT SEL

TUNE

AUX

CDCH

MAIN

INPUT SEL

SUB

AUX

VOL IN

SCL SDA S-MUTE DCERR

MCU 4

MCU

SVR

BEEP

MUTE

STBY

RR+ -

RL+ -

FR+ -

FL+ -

IC2VI

P.CON

SMALL

GND

EXT.CONT

LINE MUTE

ATT.CON

SP OUT

FRONT L

FRONT R

REAR L

REAR R

CENTER

SUB-W

MCU

SW14V

PON SW14V

A8V

SW14V

V5V

BU SW5V

BU5V PON

MCU

5.0V

3.3V

1.25V

7.8V

5.0V

3.3V

W-REMO

GND

PARK

ACC

ILLUMI

REVERSE

GND

W-REMO

PARK

ACC

ILLUMI

REVERSE

X89 (DSP)

POWER SUPPLY

● X34-382/383

BLOCK DIAGRAM

DDX8017/8027/8027Y

DDX8037/8047/8067

DDX8017/8027/8027Y DDX8037/8047/8067

BLOCK DIAGRAM

● X35-458/459

2DIN TYPE 1DIN TYPE

PON+5.0V

VGND

SW+18.5V

DGND

EJECT

KEY3

KET4

LED GND

PLL CLK

LED G

LED R

PON+3.3V

VGND

T/C HD

V GND

NTSC/PAL

PLL ON

POLS

MIRROR

VSY

HSY

BLK

MODE3

MODE2

MODE1

HPOS4

HPOS3

HPOS2

HPOS1

VCOM

PON+3.3V

BU+3.3V

XDATA

YDATA

SRC

PWM

ENABLE

T/C VD

BL GND

BL +8.5V

ESD GND

BL DET

RESET

REMO 69 70 71 72 73 74 75 76 77 78 79 80

PON+5.0V PON+5.0V NC VGND VGND SW+18.5V DGND OPEN

CLOSE NC T/C VD LED GND BRINK NC PLL CLK LED G LED R NC PON+3.3V NC VGND VB VG VR VGND T/C HD V GND NTSC/PAL PLL ON POLS MIRROR VSY HSY BLK MODE3 MODE2 MODE1 HPOS4 HPOS3 HPOS2 HPOS1 NC VCOM NC PON+3.3V AUTO DIM KEY1 XDATA YDATA X0 X1 Y0 NC PWM ENABLE SW-D NC BL GND BL GND NC BL +8.5V BL +8.5V NC DGND PH DET SW+5.0V BL DET RSENS NC RI MRI MRI M+ RI M+ EX MEX MEX M+ EX M+ NC SW-A SW-B SW-C

OPEN

IC302

POLS/HSY/VSY/BLK

MODE1/2/3/HPOS1/2/3/4 NTSC/PAL,MIRROR

OPEN

TR SW

BU3.3V

VR/VG/VB PON+5.0V

PON+3.3V VGND

IC101

DC-DC IC

VCOM

VGND

PON+3.3V

SI3.3V

PON-12.0V PON+18.5V PON+12.5V

IC203

COM AMP

IC301

TIMMING CONTROLLER

PDOS/OSCI

IC303

SW-D

SW-C

SW-B

SW-A

EX M+

EX M-

RI M+

RI M-

RSENS

15 16

REF+5.0V

SW+5.0V

PH DET

LED_G,LED R,SI3.3V

RESET,SRC,EJECT,KEY3 KEY4,REMO.ESD GND

PLL & LPF

1DIN ONLY

7 INCH INDASH MECHA

2DIN ONLY

D GND PON+5.0V

SW PCB

PON-12.0V

VGND

PON+3.3V PON+5.0V

PON+18.5V

V.COM

UPSD/CPV/ HDIR/CX/ STV1/STV2/STH1/STH2/ NGOE1/NGOE2/ NGOE3/CPH1

VGL-12.0V

STV1 UPSD

U/D(UPSD)

CPV NGOE3

OE3(NGOE3)

NGOE2

OE2(NGOE2)

NGOE1

OE1(NGOE1)

STV2

VDD1+3.3V VDD2+5.0V

VGH+18.5V

CPH1

CPH(CPH1)

CX HDIR STH1

VB VG VR

STH2

TOUCH PANEL

X0/X1/ Y0/Y1

TOUCH PANEL SWITCH CIRCUIT

PON+5.0V XDATA/YDATA

X0/X1/Y0

AUTO DIM/ KEY1

PWM/ENABLE

D.GND

LED GND BL8.5V BL GND

LED+8.5V(B) LED+8.5V(R)/LED+8.5V(G) LED GND DGND OPEN CLOSE/VOL+/VOLBRINK

IC401

VSS

STV1

CPV

STV2

VCOM

VSS VSS

VSS

L/R(HDIR)

STH1

VSS

VB VG VR

STH2

1DIN ONLY

AUTO DIMMER

SW PCB B/3

2DIN ONLY

6.5 INCH LCD

1DIN ONLY

7 INCH LCD

0.5mm 30PIN

CFL

BACK LIGHT INVERTER

1DIN ONLY

SW PCB C/3

MOTOR

SPINDLE

PICK UP

OPTICAL

STEPPING MOTOR

2 PHASE

CONNECTOR (18P,0.5PITCH)

(24P,0.5PITCH)

CONNECTOR

CONNECTOR (10P,0.5PITCH)

(2P,PIN ASSY)

CONNECTOR

ACTUATER DRIVER

IC2

PROCESSOR

FRONT END

APC TR

Q7,Q8

Q1,Q2

THERMISTER

RESET IC

IC4

EEPROM

IC11

FLASH ROM

IC3

(50P,0.5PITCH)

CONNECTOR

DISC CONTROLLER

OPTICAL

(4P,0.5PITCH)

CONNECTOR

3.3V REG.

IC10

A3.3V D3.3V

D5V

A5V

IC9

1.5V REG.1.5V

VOLT AGE DET

IC8

IC5

MOTOR &

IC1

CN4

CN3

CN2

CN1 CN5

CN6

CN1

HALL BIAS

HALL SENSOR

U,V,W, COIL

DVD LD/CD LC VC (2.2V)

MODE SW/GAIN SW FO+-,TR+-

PD/VR DVD/VR CD I/V OUT (DVD/CD)

P5V

DC MOTOR

LO/EJ

3PHASE PWM

PWM*2

VHALF

A,B,C, D,E,F,RF (P,N)

SCK,STDI

SEN

VHALF

A5V

ARF,NARF FBAL

JLINE,TSTSG FE,AS,REFNV,RFDIFO

OFTR,BDO,VREF2 VHALF (16.5V)

TRCRS TE

DVDON/CDON

SEN SCK,STDI

A3.3VA5V

A3.3V

DISC

A3.3VD5V 1.5VD3.3V

IOP- (AD)

TEMP DET (AD)

16.897849MHz

D3.3V

GAIN SW

PWM8,DRV.MUTE,LO.MTE,B

SPDRV,FODRV,TRDRV

MS,STEP A,STEP B

FG,EXCNT1

SDA,SCL

FADR0-FADR17,

NCE,NWE,NOE

FDT0-FDT7

D3.3V

821

S/P DIF

AUDIO OUT

CD-DA

ATAPI IF

D5V

P5V

DISC DET

A B

D E

D5V

LIM SW

VREF,EC

PWM*2

SW A,B,C,D,E

LIM-SW

NRST

FFC

● X37-107 (DVD mechanism)

BLOCK DIAGRAM

DDX8017/8027/8027Y

DDX8037/8047/8067

DDX8017/8027/8027Y DDX8037/8047/8067

COMPONENTS DESCRIPTION

● VIDEO CONTROL UNIT (X14-955/956x-xx)

Ref. No. Application / Function Operation / Condition / Compatibility

IC1 DC-DC power supply IC For controlling BL8.5V and ±7V IC2 DC-DC power supply IC For controlling SW6.5V and MECHA7.5V IC3 DC-DC power supply IC For controlling SW3.3V and SW2.5V IC9 Regulator IC 2V generation for IC601 IC80 Regulator IC Backup 3.3V generation IC81 Regulator IC SW5V generation IC82 Regulator IC V3.3V generation IC101 E2PROM Memory for µ-com IC103 Logic IC (AND) AND for remote controller and wired remote controller IC104 µ-com IC For controlling the main unit IC105 Resetting IC For resetting µ-com IC107 Motor driver IC Tilted control of tilting mechanism IC108 Logic IC (AND∗4) 3.3V → 5V conversion

IC237

IC238 Logic IC (Inverter) For blank signal reversal coming from X35 IC239 Color differentiation signal 1H-DELAY For delaying 1H color differential signals when PAL IC240 RGB switch For switching RGB signals coming from DVD signal and X34 IC400 Ope amp IC For audio LPF IC401 Regulator IC 5V generation for audio IC402 Audio DAC For converting digital signals into analog signals IC403 Logic IC (Inverter) SPDIF driver IC470 CPLD Audio DAC control IC500 Regulator 5V generation for DVD mechanism IC520 FLASH ROM For MPEG decoder control program IC560 SDRAM RAM for temporary storage of decoded signal IC601 MPEG decoder IC for decoding MPEG encoded signal IC640 Clock generator 27M, 36.864MHz clock generation IC641 Logic IC (D-FF) 13.5MHz is generated by frequency dividing from 27MHz IC650 LPF and Driving IC for video signal For RGB and composite signals of DVD IC651 Regulator V5V generation IC652 Video encoder Conversion of digital video signals into analog signals IC654 Video switch For switching DVD composite signal and composite signal from X34 IC700 GRITT IC Graphic signal generation IC701 Regulator IC700 1.8V generation IC750,751 SDRAM GRITT-IC storage RAM IC770 Logic IC (NOR) GRITT-IC video clock frequency dividing IC771 Logic IC (D-FF∗4) GRITT-IC video clock frequency dividing IC772 Logic IC (Inverter) GRITT-IC video clock frequency dividing

Signal processing IC for driving color liquid crystal panel

RGB signal generation for liquid crystal

DDX8017/8027/8027Y DDX8037/8047/8067

COMPONENTS DESCRIPTION

Ref. No. Application / Function Operation / Condition / Compatibility

IC773 Logic IC (AND) GRITT-IC video clock frequency dividing IC774 Logic IC (OR) GRITT-IC video clock frequency dividing IC779 Logic IC (NAND) GRITT-IC video clock frequency dividing IC781 Logic IC (Inverter) For reversing switching used for graphic signal and other signals IC800 SH-3 µ -com For GRITT-IC control IC801 Regulator IC800 1.9V generation IC830 IC831 Logic IC (Inverter) For reversing GRITT-IC HD IC832 Logic IC (D-FF) For GRITT-IC VD generation when using NAVI IC833 Logic IC (D-FF) VD generation for µ-com input IC834 Logic IC (Inverter∗3) For reversing IC830 output HD IC835 Logic IC (Data selector∗4) For HD/VD selection for GRITT-IC (NAVI or otherwise) IC836 Logic IC (AND) VD buffer for IC237/timing control IC850 FLASH ROM For SH-3 µ-com program IC851 SRAM SH-3 µ-com RAM IC852 SDRAM SH-3 µ-com RAM IC853 Logic IC (AND) For SRAM control IC854 Logic IC (BUS SWITCH) SRAM control IC855 Logic IC (Inverter) SRAM control Q1 Small signal NPN transistor For ACC detection Q2 PNP digital transistor For PARK detection Q3 NPN digital transistor For SW 14.4V control Q4 Small signal NPN transistor For DC-DC external oscillation frequency input clamp Q5 Small signal PNP transistor For temperature compensation of DC-DC external oscillation frequency input clamp Q6 FET For SW 14.4V control Q7 Q8 Small signal NPN transistor For fan power supply 12.8V generation Q9 NPN digital transistor For DC-DC oscillation frequency switching Q10 Small signal PNP transistor For fan power supply 12.8V generation Q11 Small signal NPN transistor For fan power supply 12.8V generation Q13 FET For BL8.5V and ±7V generation Q16 NPN digital transistor For DC-DC oscillation frequency switching Q19 FET For SW6.5V/MECHA7.5V generation Q20 NPN digital transistor For DC-DC oscillation frequency switching Q22 FET For SW3.3V/SW2.5V generation Q23 NPN digital transistor Q24 Small signal NPN transistor For DC-DC external oscillation frequency input clamp Q25 PNP digital transistor Q26 Small signal NPN transistor For DC-DC external oscillation frequency input clamp Q27 PNP digital transistor

PLL built-in synchronization separation IC

PNP transistor for medium power amplification

HD/VD generation from composite signal by synchronization separation

For fan power supply 12.8V generation

For REF voltage impulse at the time of DC-DC external oscillation frequency input stoppage

DDX8017/8027/8027Y DDX8037/8047/8067

COMPONENTS DESCRIPTION

Ref. No. Application / Function Operation / Condition / Compatibility

Q80 NPN digital transistor For reduced/excess current detection circuit Q81 Small signal NPN transistor For reduced/excess current detection circuit Q82 Small signal PNP transistor For reduced/excess current detection circuit Q83 Small signal NPN transistor For reduced/excess current detection circuit Q84 PNP digital transistor For reduced/excess current detection circuit Q85 Small signal NPN transistor For reduced/excess current detection circuit Q86 Small signal PNP transistor For reduced/excess current detection circuit Q87 PNP digital transistor For reduced/excess current detection circuit

Q88

Q89~91 Small signal NPN transistor 8.5V regulation circuit for BU3.3V Q92 Small signal PNP transistor 8.5V regulation circuit for BU3.3V Q93 NPN digital transistor For reduced/excess current detection circuit Q94 PNP digital transistor For SW14.4V control

Q95

Q103 NPN digital transistor For GREEN_LED control Q104 PNP digital transistor For GREEN_LED control Q105 NPN digital transistor For RED_LED control Q106 PNP digital transistor For RED_LED control Q107 PNP digital transistor For resetting Q108 NPN digital transistor For resetting Q109 Small signal PNP transistor For switching µ-com AD conversion reference voltage BU3.3V/SW3.3V Q110 NPN digital transistor For switching µ-com AD conversion reference voltage BU3.3V/SW3.3V Q111 Small signal PNP transistor For switching µ-com AD conversion reference voltage BU3.3V/SW3.3V Q112,113 Small signal NPN transistor For switching µ-com AD conversion reference voltage BU3.3V/SW3.3V Q114 PNP digital transistor For resetting Q115 NPN digital transistor For setting to OV until setting is completed, immediately after resetting µ-com 20 pin Q171 Small signal PNP transistor µ-com input voltage 5V → 3.3V conversion Q173 Small signal NPN transistor µ-com input voltage 5V → 3.3V conversion Q230 Small signal NPN transistor For input video signal clamp to IC237 Q231 Small signal NPN transistor For brightness signal input buffer to IC237 Q232 Small signal PNP transistor For color signal input buffer to IC237 Q233 NPN digital transistor For IC240 switching control Q234 Small signal PNP transistor For switching at the time of chroma trap PAL Q236 Small signal NPN transistor For IC237 3V generation Q237 Small signal PNP transistor For IC237 3V generation Q238,239 Small signal NPN transistor For IC237 7.5V generation (7.5V fluctuates a little.) Q240 Small signal PNP transistor For IC237 7.5V generation (7.5V fluctuates a little.) Q400,401 Small signal NPN transistor For audio signal muting

PNP transistor for low-frequency power amplification

NPN transistor for low-frequency general amplification∗2

8.5V regulation circuit for BU3.3V

For SW14.4V control

DDX8017/8027/8027Y DDX8037/8047/8067

COMPONENTS DESCRIPTION

Ref. No. Application / Function Operation / Condition / Compatibility

Q402 Small signal NPN transistor For audio signal muting control Q403 NPN digital transistor For audio signal muting control Q404,405 PNP digital transistor For audio signal muting control Q650 PNP digital transistor Resetting 3.3V → 5V conversion for IC652 Q651 NPN digital transistor Resetting 3.3V → 5V conversion for IC652 Q652 NPN digital transistor For reversing RGB_SW Q653 NPN digital transistor For DVD composite muting Q700 Small signal PNP transistor For GRITT-IC video signal reference voltage generation Q701 Small signal NPN transistor For GRITT-IC video signal reference voltage generation Q771,772 Small signal NPN transistor For GRITT-IC video clock amp Q830 PNP digital transistor NT/PAL control 3.3V → 5V conversion for IC830 Q831 NPN digital transistor NT/PAL control 3.3V → 5V conversion for IC830 Q901 NPN digital transistor For ILLUMI detection Q902 NPN digital transistor For REVERSE detection

● ELECTRIC UNIT (X34-382/383x-xx)

Ref. No. Application / Function Operation / Condition / Compatibility

IC50 3-terminal regulator IC 8.4V for audio is generated from BU14V IC52 Power supply conversion IC ±9.0V for 5V pre-out is generated from BU14V IC54 3-terminal regulator IC 5V for video is generated from BU14V IC100 Power IC Power amplifier for speaker output IC150 Operational amplifier Audio mid-point electrical potential 3.3V, SVR voltage 6.8V buffer IC151 Electrical volume and Selector IC Audio volume control, audio signal selection IC200 Operational amplifier For 5V pre-out audio signal amplification (Front) IC201 Operational amplifier For 5V pre-out audio signal amplification (Rear) IC202 Operational amplifier For 5V pre-out audio signal amplification (Sub-woofer) IC203 Isolation amplifier IC For audio signal GND isolation (AVIN2) IC204 Isolation amplifier IC For audio signal GND isolation (AVIN1) IC251 RDS decoder IC For RDS signal processing and demodulation IC300 Voltage detector For µ-com resetting voltage monitoring IC301 Logic IC (NOR) Muting control for audio IC303 Audio microcomputer For X34 board control IC400 Video switch For video signal selection (R) IC401 Video switch For video signal selection (G) IC402 Video switch For video signal selection (B) IC403 Synchronization separation IC For NT/PAL recognition, AVIN/Rear camera auto detection IC404 Video switch Video signal selection (Synchronization separation) IC405 Isolation amplifier IC For audio signal GND isolation (TV) IC406,407 IC408 Video switch Video signal selection (For AVOUT)

Video switch Video signal selection (For monitoring main unit)

DDX8017/8027/8027Y DDX8037/8047/8067

COMPONENTS DESCRIPTION

Ref. No. Application / Function Operation / Condition / Compatibility

IC413 Logic IC (Multiplexer) For audio signal selection (For MAIN source) IC414 Logic IC (Multiplexer) For audio signal selection (For 2-ZONE sources) IC415 Video switch Video signal selection (For monitoring main unit) IC416 Video switch Video signal selection (For AVOUT) IC500 Isolation amplifier IC For audio signal GND isolation (LX) IC501 Logic IC (Inverter) For reversing resetting signal IC502 Logic IC (Buffer) Buffer for remote control signal for NAVI Q6 ANT-CONT SW Comes on when TUNER source is selected Q7 P-CONT SW Goes OFF when STANDBY source is selected Q8~10 For P-CONT circuit control Controlling P-CONT circuit Q11 For P-CONT circuit control Controlling P-CONT circuit Q12 BU detection SW Comes ON power supply voltage is about 8.8V or more Q13 For EXT-AMP control Control of external amplifier Q14 For surge voltage detection Comes ON when Q15 is ON Q15 For surge voltage detection Comes ON when power supply voltage is about 20V or more Q50 For ±9V power supply Comes ON when Q51 is ON Q51 For ±9V power supply Comes ON when SW14V is ON Q52 SW14V power supply SW Comes on at P-ON Q54 For BU5V power supply Q55 A8V oversupply SW Comes ON when SW14V is ON Q58 For BU5V power supply Q59 A8V power supply BU14V → 8V for audio is supplied Q61 V5V power supply SW Comes ON when SW14V is ON Q62 SW5V power supply SW Comes ON at P-ON Q63 For SW5V power supply BU5V → SW5V is supplied Q64 For V5V power supply BU14V → 5V for video is supplied Q65~70 For ±9V power supply

Q150

Q151 For SVR voltage reduction control Electric current control of SVR voltage reduction circuit Q152 Q200 For audio muting Audio muting of pre-out front right channel Q201 For audio muting Audio muting of pre-out front left channel Q202 For audio muting Audio muting of pre-out rear left channel Q203 For audio muting Muting at momentary power down, resetting, and audio mute timing Q204 For audio muting Audio muting of pre-out rear right channel Q205 For audio muting Audio muting of pre-out center channel Q206 For audio muting Audio muting of pre-out sub-woofer channel Q207 For audio muting Audio muting of AVOUT right channel Q208 For audio muting Muting at momentary power down, resetting, and audio mute timing

SVR6.8V, audio 3.3V, IC150 power supply SW

SVR6.8V, audio 3.3V, IC150 power supply

Comes ON when SW14V is ON

Power supply to IC150, voltage supply to Q151

DDX8017/8027/8027Y DDX8037/8047/8067

COMPONENTS DESCRIPTION

Ref. No. Application / Function Operation / Condition / Compatibility

Q209 For audio muting Audio muting of AVOUT left channel Q250 AM power supply SW Comes ON when AM source is selected Q252 For AM power supply Audio 8V is supplied when AM source is selected Q403,404 SW for audio selector control Converts IC413 µ-com controlled terminal voltage: 5V → 8V Q405,406 SW for audio selector control Converts IC414 µ-com controlled terminal voltage: 5V → 8V Q500 For reversing resetting signal voltage Reverses signal in order to obtain resetting signal for TV tuner Q800 MUTE 0 terminal control SW MUTE 0 audio muting control

● VIDEO UNIT (X35-458/459x-10)

Ref. No. Application / Function Operation / Condition / Compatibility

IC1 Inverter control IC Control and drive of inverter circuit for backlight IC101 DC/DC converter IC ±12V power supply for VCOM amp, -12.0V/+18.5V LCD power supply IC203 VCOM amp VCOM signal amplification amp IC300 Three states buffer Start pulse switching SW IC301 Timing controller IC LCD module control IC302 AND V.SYNC delay buffer IC303 PLL LPF LPF for PLL control (VT voltage control) IC601 Remote controller light receptor IC Remote controller light receptor Q1 Dimmer SW ON/OFF control signal of PWM and put on dimmer on backlight Q2,3 Inverter driver Inverter circuit driving Q5 5V AVR 5V power supply for inverter control IC Q101 Switch Switch for controlling DC/DC converter Q102 Switch Switch for controlling DC/DC converter Q202,203 VCOM driver VCOM signal buffer Q300 Switch For switching IC205 Q301 VCO For PLL oscillation Q302 Touch panel X1 SW X1 SW: Comes on at panel touch detection or at X-axis input and impresses voltage Q303 Touch panel Y1 SW Y1 SW: Comes on at Y-axis input and impresses voltage Q304 Touch panel X0 SW X0 SW: Comes on at X-axis input and impresses voltage Q305 Touch panel Y0 SW Y0 SW: Comes on at Y-axis input and impresses voltage Q306 Touch panel Y0/Y1 SW Y0/Y1 SW: Comes on at Y-axis input and goes off at X-axis input Q307,308 Buffer For PLL clock Q601,602 Switch SI blinking switch Q604,605 Switch Hard resetting switch Q701 Switch DISC Illumination switch

● DAUGHTER UNIT (X89-274/279x-11)

Ref. No. Application / Function Operation / Condition / Compatibility

IC2 OP amp For audio signal amplification (Center, Sub-woofer) IC3 OP amp For audio signal amplification (Rear)

DDX8017/8027/8027Y DDX8037/8047/8067

COMPONENTS DESCRIPTION

Ref. No. Application / Function Operation / Condition / Compatibility

IC4 OP amp For audio signal amplification (Front) IC5 3-terminal regulator 5V is output from 8V IC6 Audio DAC D/A conversion of audio signal (Front, Rear, Center, Sub-woofer) IC7 A/D converter A/D conversion of audio signal (Lch, Rch) IC9 DSP Processing of computing for Dolby 5.1ch, dts etc. IC10 DIR Conversion of S/PDIF format data to digital audio format IC11 OP amp For audio signal amplification (Front) IC12 Analog switch Switching audio signal (Sub-woofer) and A4V IC18 Logic IC Inverter for generating clock IC19 3-terminal regulator 1.25V his output from 3.3V IC20,21 3-terminal regulator 3.3V is output from 5V IC300 DC/DC converter For control of 5V and 7.8V Q13 Digital transistor Q14,15 Transistor for audio muting Q300,302 Digital transistor Q303 FET For generation of 5V and 7.8V Q306~310 Q312 FET For SW14.4V generation Q313 Transistor∗2For SW14.4V control

Digital transistor For Power ON control

Comes ON at the time of momentary power down, resetting, and in audio muting timing Comes Mute at the time of momentary power down, resetting, and in audio muting timing Reference for voltage input at the time of DC-DC external oscillation frequency input stoppage

● DVD UNIT (X37-1070-00)

Ref. No. Application / Function Operation / Condition / Compatibility

IC1 RF signal processing IC RF signal processing IC2 Driver Driver for motorists/pickup actuators IC3 FLASH ROM FW maintenance for optical DISC control IC IC4 µ-com built-in optical DISC control IC Optical DISC control in general/ATAPI interface IC5 Voltage detection IC For reset of optical DISC control IC IC8 Voltage detection IC For monitoring power supply voltage IC9 S1.5V power supply IC S5V → S1.5V IC10 S3.3V power supply IC S5V → S3.3V IC11 EEPROM Data storage for optical DISC control IC Q1 MOS-FET DVD laser diode ON/OFF control Q2 MOS-FET CD laser diode ON/OFF control Q7 APC transistor CD laser diode light emission amount control Q8 APC transistor DVD laser diode light emission amount control Q9 MOS-FET For CD laser diode protection Q10 MOS-FET For DVD laser diode protection Q11 Resistor built-in transistor LO-MUTE signal control Q12 Resistor built-in transistor FG signal control Q13 Resistor built-in transistor BMS signal control Q14 Resistor built-in transistor DRMU signal control

DDX8017/8027/8027Y DDX8037/8047/8067

MICROCOMPUTER’S TERMINAL DESCRIPTION

● System Microcomputer: 703264YGJ501A (X14: IC104)

Pin No. Pin Name

1AVREF0 2AVSS 3,4 NC 5AVREF1 6 V_MUTE VIDEO O Video mute H: MUTE ON 7HD VIDEO I Graphic 7NC OOSD 8 FLMD0 µCOM I 9 VDD 10 REGC 11 VSS 12 X1 4.953MHz 13 X2 14 RESET µCOM I 15 XT1 32.768kHz 16 XT2 17 NC 18 VD VIDEO I (Graphic) 18 NC O OSD 19 BU_DET 20 DISK_DET 21 ACC_DET 22 MINI_SDATA PANEL I Data input from mini liquid crystal 23 NC O 24 MINI_CLKIN PANEL I Communication clock with mini liquid crystal 25 BE_MDATA B/E O Data output to B/E-IC 26 BE_SDATA B/E I Data input from B/E-IC 27 BE_CLK B/E I Communication clock with B/E-IC 28 BE_MREQ B/E O Request to B/E-IC 29 BE_SREQ B/E I Request from B/E-IC 30 REMO PANEL I Remote controller 31 S_MUTE VIDEO O Composite signal mute L: FULL GRAPHIC (OSD), H: OTHER 32 NC 33 EVSS 34 EVDD 35 SDA/E2P_SDA µCOM I/O Access with E2P 35 35 36 SCL/E2P_SCL µCOM I/O Access with E2P 36

SDA/ROM_COR_SDA SDA/CHROMA_SDA_SDA

SCL/ROM_COR_SCL

Module (physical)

Power supply DVD_MECHA Power supply

µCOM I/O Chroma γ I/O Access with chroma γ IC

µCOM I/O

I/O Application Processing Operation Description

I Back up detection H: Reduced electric power detection I Disk detection L: Disc IN IACC detection H: ACC reduced electric power detection

Access with E2P at coping with ROM correction

DDX8017/8027/8027Y DDX8037/8047/8067

MICROCOMPUTER’S TERMINAL DESCRIPTION

Pin No. Pin Name

36 37 BE_RST B/E O B/E circuit reset L: RESET 38 POWER_DET 39 BL_DET INVERTER I Backlight abnormality detection H: Abnormality detection 40 B_PON 41,42 NC O 43 FSEL1 44 FSEL2 45 FSEL_SW 46 PON 47 MCNT 48 RGB_SW VIDEO O RGB signal switching L: DVD, H: OTHER 49 OSD_CS OSD O OSD-IC chip select (OSD) 50 OSD_DATA OSD O Data output to OSD-IC (OSD) 51 OSD_CLK OSD O Clock output to OSD-IC (OSD) 52 OSD_RST OSD O Resetting OSD-IC (OSD) 53 WRT_E2P µCOM I Used for E2P writing

54 POWER_PWM

55 JIG_EJ EXTRA I 2DIN 56 PWM INVERTER O Liquid crystal brightness control 57 STATUS0 JIG O For monitor mechanism endurance Jig 58 STATUS1 JIG O For monitor mechanism endurance Jig 59 PANEL_DET PANEL I Front panel attach/detach detection H: Detached, L: Attached 2DIN L-fixed 60 STATUS2 JIG O For monitor mechanism endurance Jig 61 SH_MDATA SH-3 O Data output to SH-3 µ-com (GRAPHIC) 62 SH_SDATA SH-3 I Data input from SH-3 µ-com (GRAPHIC) OSD is output 63,64 NC O 65 SYS_SREQ BOX I Request from BOX µ-com 66 SYS_MREQ BOX O Request to BOX µ-com 67 SYS_ON BOX O BOX µ-com ON/OFF control H: ON, L: OFF 68 SYS_SDATA BOX I Data input from BOX µ-com 69 SYS_MDATA BOX O Data output to BOX µ-com 70 SYS_CLK BOX O Communication clock with BOX µ-com 250kHz 71 MINI_CS/MINI_CS PANEL O Communication with mini liquid crystal 71 72 72 72 73 73

SCL/CHROMA_SCL

MINI_CS/FLASH_SDATA MINI_MDATA/MINI_MDATA MINI_MDATA/SUBLED_SW MINI_MDATA/FLASH_MDATA MINI_CLK/MINI_CLK MINI_CLK/FLASH_CLK

Module (physical)

Chroma γ I/O Access with chroma γ IC

Power supply

Power supply Power supply Power supply Power supply Power supply

Power supply

µCOM I For flash writing PANEL O Communication with mini liquid crystal PANEL O µCOM O For flash writing PANEL O Communication with mini liquid crystal µCOM I For flash writing

I/O Application Processing Operation Description

I 8.5V over current detection H: Abnormality detection

O SW14 (BU SW)ON/OFF control H: ON

O DC-DC IC oscillation frequency switching O DC-DC IC oscillation frequency switching O Control at DC-DC IC FSEL switching Normal: H, At FSEL switching: L OPower supply ON/OFF control H: ON O

Motor driver voltage switching (MECHA7V) (1DIN)

O DC/DC-IC oscillation frequency control

Model without mini liquid crystal LED ON/OFF

H: 7V, L: 5V

PWM output. At FSEL switching stopped. (Output L)

HI: ON

DDX8017/8027/8027Y DDX8037/8047/8067

MICROCOMPUTER’S TERMINAL DESCRIPTION

Pin No. Pin Name

74 74 75 SRC PANEL I Source key L: ON 76 EJECT PANEL I Eject key (1DIN) L: ON 2DIN HI-fixed input 77 MINI_PON PANEL O MINI liquid crystal Power supply control H: ON, L: OFF 78 DSI PANEL O DSI control (1DIN) 79 ILL_DET 80 PAK_DET 81 REV_DET 82~84 NC O 85 SH_INI SH-3 O (GRAPHIC) 86 SH_STBY SH-3 I (GRAPHIC) 87 SH_SREQ SH-3 I Request from SH-3 µ-com (GRAPHIC) 88 SH_MREQ SH-3 O Request to SH-3 µ-com (GRAPHIC) 89 SH_CON SH-3 O (GRAPHIC) 90 SH_RST SH-3 O SH-3 µ-com resetting (GRAPHIC) 91 TOUCH SH-3 I (GRAPHIC) 92 TOUCH_EN SH-3 O (GRAPHIC) 93 NAVI_L VIDEO O L: NAVI, H: OTHER 94~97 TYPE0~TYPE3 EXTRA I Destination setting Refer to destination setting 98 SUBLED_OFF Other X35 O 2DIN disc LED control (2DIN) 99 TMOTOR_M 99 TILT_UP 100 TMOTOR_P 100 TILT_DOWN 101 SMOTOR_M 102 SMOTOR_P 103 BVSS 104 BVDD 105 SW_A 106 SW_B 107 SW_C 108 SW_D 109 ENABLE INVERTER O Backlight ON/OFF control H: ON 110 FLMD1 µCOM I 111 Y0 Touch panel O Touch panel control (OSD) 112 X1 Touch panel O Touch panel control (OSD) 113 X0 Touch panel O Touch panel control (OSD) 114~117 118~120 121 MIRROR LCD O Rear monitor mirror control

OPEN_CLOSE/OPEN_CLOSE OPEN_CLOSE/EJECT

HPOS1~HPOS4 LCD O Display position control MODE1~MODE3 LCD O Aspect setting

Module (physical)

PANEL I OPEN_CLOSE key (1DIN) L: ON PANEL I

Power supply Power supply Power supply

1DIN_MECHA 2DIN_MECHA 1DIN_MECHA 2DIN_MECHA 1DIN_MECHA 1DIN_MECHA

1DIN_MECHA 1DIN_MECHA 1DIN_MECHA 1DIN_MECHA

I/O Application Processing Operation Description

Tilt mechanism OPEN/CLOSE and eject (2DIN)

I ILLUMI detection H: Normal, L: Detect IParking detection H: Normal, L: Detect IReverse detection H: Normal, L: Detect

O Monitor mechanism tilt control (1DIN) O Tilt mechanism control (2DIN) O Monitor mechanism tilt control (1DIN) O Tilt mechanism tilt control (2DIN) O Monitor mechanism slide control (1DIN) O Monitor mechanism slide control (1DIN)

I Monitor mechanism detection(1DIN) 2DIN is OUT I (1DIN) 2DIN is OUT I Monitor mechanism detection 2DIN is OUT I Monitor mechanism detection 2DIN is OUT

L: ON

DDX8017/8027/8027Y DDX8037/8047/8067

MICROCOMPUTER’S TERMINAL DESCRIPTION

Pin No. Pin Name

122 ILL_R PANEL O Key ILLUMI red ON/OFF H: ON, L: OFF 123 ILL_G PANEL O Key ILLUMI green ON/OFF H: ON, L: OFF 124 ILL_B PANEL O Mini liquid crystal backlight blue ON/OFF H: ON, L: OFF 125 NTSC_PAL VIDEO O 126 LED_SW/SI Other X35 O 126 LED_SW/SI Other X35 O SI control (2DIN) H: Light turn ON, L: Light turned OFF 127 LCD_PON LCD O LCD power supply ON/OFF control H: ON 128~134 135 TL_DET 136 KEY1 PANEL I 4 key monitor mechanism section (1DIN) 137 KEY2 PANEL I 8 key attach/detach panel section (1DIN) 138 KEY3 PANEL I 6 key panel section (2DIN) 139 KEY4 PANEL I 6 key panel section (2DIN) 140 R_SENS 140 R_SENS 141 PH_DET 142 AUTO_DIM Other X35 I Auto dimmer input 143 YDATA Touch panel I Touch data input (OSD) 144 XDATA Touch panel I Touch data input (OSD)

NC O

Module (physical)

Power supply

1DIN_MECHA 2DIN_MECHA 1DIN_MECHA

I/O Application Processing Operation Description

LCD output signal NT/PAL identification output LED blinking control at OPEN/CLOSE (1DIN)

Power supply reduced electric power detection

I Monitor mechanism tilt sensor (1DIN) I Tilt mechanism tilt sensor (2DIN) I Monitor mechanism slide detection (1DIN)

H: PAL, L: NTSC H: Light turn ON, L: Light turned OFF

Destination setting of GRAPHIC model and OSD model

CLASSIFICATION CATEGORY MODEL NAME DESTINATION TYPE3 TYPE2 TYPE1 TYPE0

GRAPHIC 1DIN KVT-817DVD K 0 0 0 1

KVT-827DVD E 0 0 1 0 KVT-837DVD M 0 0 1 1 KVT-847DVD/867DVD V/X 0 1 0 0

2DIN DDX8017 K 1 0 0 1

DDX8027 E 1 0 1 0 DDX8037 M 1 0 1 1 DDX8047/8067 V/X 1 1 0 0

OSD 1DIN KVT-717DVD K 0 0 0 1

KVT-627DVD/727DVD E 0 0 1 0 KVT-737DVD M 0 0 1 1 KVT-747DVD/767DVD V/X 0 1 0 0 KVT-747DVD R 0 1 1 1

2DIN DDX7017 K 1 0 0 1

DDX6027 E 1 0 1 0 DDX7037 M 1 0 1 1 DDX7047/7067 V/X 1 1 0 0 DDX7047 R 1 1 1 1

DDX8017/8027/8027Y DDX8037/8047/8067

MICROCOMPUTER’S TERMINAL DESCRIPTION

● Graphic Microcomputer: 6417706F120DV (X14: IC800)

Pin No. Pin Name Module I/O Application Processing Operation Description

1 Vcc-RTC 2XTAL2 EXTRA O Built-in RTC crystal oscillator terminal NC 3 EXTAL2 EXTRA I Built-in RTC crystal oscillator terminal Pull-up to Vcc 4 Vss-RTC 5~10 D31~D26 EXTRA I/O Data bus 11 VssQ 12 D25 EXTRA I/O Data bus 13 VccQ 14~18 D24~D20 EXTRA I/O Data bus 19 Vss 20 D19 EXTRA I/O Data bus 21 Vcc 22~24 D18~D16 EXTRA I/O Data bus 25 VssQ 26 D15 EXTRA I/O Data bus 27 VccQ 28~36 D14~D6 EXTRA I/O Data bus 37 VssQ 38 D5 EXTRA I/O Data bus 39 VccQ 40~44 D4~D0 EXTRA I/O Data bus 45~48 A0~A3 EXTRA O Address bus 49 VssQ 50 A4 EXTRA O Address bus 51 VccQ 52~60 A5~A13 EXTRA O Address bus 61 VssQ 62 A14 EXTRA O Address bus 63 VccQ 64~70 A15~A21 EXTRA O Address bus 71 Vss 72 A22 EXTRA O Address bus 73 Vcc 74~76 A23~A25 EXTRA O Address bus 77 BS EXTRA O Bus cycle start signal 78 RD EXTRA O Lead strobe 79 WE0/DQMLL EXTRA O D7~D0 select signal /DQM (SDRAM) 80 WE1/DQMLU EXTRA O D15~D8 select signal /DQM (SDRAM) 81 WE2/DQMUL EXTRA O D23~D16 select signal /DQM (SDRAM)

Power supply

-RTC power supply 1.9V

- I/O power supply 3.3V

- Internal power supply 1.9V

- I/O power supply 3.3V

- Internal power supply 1.9V

DDX8017/8027/8027Y DDX8037/8047/8067

MICROCOMPUTER’S TERMINAL DESCRIPTION

Pin No. Pin Name Module I/O Application Processing Operation Description

82 WE3/DQMUU EXTRA O D31~D24 select signal /DQM (SDRAM) 83 RDWR EXTRA O Read/Write 84 VssQ 85 CS0 EXTRA O Chip select 0 (ROM) For ROM 86 VccQ 87 CS2 EXTRA O Chip select 2 (For DMA) 88 CS3 EXTRA O Chip select 3 (SDRAM) For SDRAM 89 CS4 EXTRA O Chip select 4 (SRAM) For SRAM 90 CS5 EXTRA O Chip select 5 (GRiTT: VRAM) For GRITT 91 CS6 EXTRA O Chip select 6 (GRiTT: Register) For GRITT 92 NC O 93 VssQ 94 NC O 95 VccQ 96 RAS EXTRA O Row address strobe 97 NC O NC 98 CAS EXTRA O Colum address strobe 99 NC O 100 CKE EXTRA O Clock enable 101 SHINI V850 I Resetting start identification H: Other than reset start, L: Reset start 102 BACK EXTRA O Bus acknowledge NC 103 BREQ EXTRA I Bus right request High level fixed. 104 R_WAIT GRITT I Hardware wait request 105 SH_DACK GRITT O DMA acknowledge 106,107

108 SHSTBY V850 O Power supply OFF permission

109 AUDATA0 H-UDI I/O AUDATA input/output 110 AUDATA1 H-UDI I/O AUDATA input/output 111 AUDATA2 H-UDI I/O AUDATA input/output 112 AUDATA3 H-UDI I/O AUDATA input/output 113 AUDSYN.C H-UDI O AUDSYNC output (H-UDI) 114 TDI H-UDI I Data input (H-UDI) 115 Vss 116 TCK H-UDI I Clock (H-UDI) 117 Vcc 118 TMS H-UDI I Mode select (H-UDI) 119 TRST H-UDI I Reset (H-UDI) 120 TDO H-UDI O Data output (H-UDI) 121 ASEBRKAK H-UDI O ASE break acknowledge (H-UDI)

NC O

Power supply

- I/O power supply 3.3V

H: Power supply OFF not permitted L: Power supply OFF permitted

- Internal power supply 1.9V

DDX8017/8027/8027Y DDX8037/8047/8067

MICROCOMPUTER’S TERMINAL DESCRIPTION

Pin No. Pin Name Module I/O Application Processing Operation Description

122 ASEMD0 H-UDI I ASE mode (H-UDI) 123 Vcc-PLL1 124 CAP1 125 Vss-PLL1 126 Vss-PLL2 127 CAP2 128 Vcc-PLL2 129 MD1 EXTRA I Clock mode setting 130 Vss 131 XTAL EXTRA O Crystal oscillator terminal NC 132 EXTAL EXTRA I 133 NC O 134 SH_SREQ V850 O 135 SH_MREQ V850 I 136 NC O 137 VssQ 138 CKIO EXTRA O System clock output 139 VccQ 140,141 142 SH_SDATA V850 UART 143 NC O 144,145 146 SH_MDATA V850 UART 147 R_INT GRITT I Interruption request from graphic IC 148 Vss 149 RESETM EXTRA I Manual resetting request High level fixed 150 Vcc 151 TOUCH V850 O Touch off detection H: Touch OFF, L: Touch ON 152 TOUCH_EN V850 I Touch control enable 153 X1 X35 O Touch panel control 154 X0 X35 O Touch panel control 155 SHCON V850 I Graphic µ-com operation control H: Operation possible, L: Operation not possible 156 VssQ 157 NMI EXTRA I Non-maskable interruption Low level fixed 158 VccQ 159 AUDCK H-UDI I AUDCK input (H-UDI) 160 R_DREQ GRITT I DMA request 161 Y0 X35 O Touch panel control 162 NC I Low level fixed 163 MD0 EXTRA I Clock mode setting High level fixed

NC O

NC I

Power supply Power supply Power supply Power supply Power supply Power supply

Power supply

- PLL1 power supply 1.9V

- PLL1 external capacity terminal 470pF

- PLL2 external capacity terminal 470pF

- PLL2 power supply 1.9V

External clock input / Crystal oscillator terminal

- I/O power supply 3.3V

- Internal power supply 1.9V

H: Touch control possible, L: Touch control not possible

- I/O power supply 3.3V

DDX8017/8027/8027Y DDX8037/8047/8067

MICROCOMPUTER’S TERMINAL DESCRIPTION

Pin No. Pin Name Module I/O Application Processing Operation Description

164 MD2 EXTRA I Clock mode setting Low level fixed 165 SH_RST V850 I 166 CA EXTRA I Hardware standby request High level fixed 167 MD3 EXTRA I CS0 space bus width designation Low level fixed 168 MD4 EXTRA I CS0 space bus width designation High level fixed 169 MD5 EXTRA I Endean setting Low level fixed 170 Avss 171 XDATA X35 I Touch panel input (X-direction) 172 YDATA X35 I Touch panel input (Y-direction) 173,174 175 Avcc 176 AVss

NC O

Power supply

Power supply Power supply

-Power supply for analog 3.3V

● Audio Microcomputer: 703068YGJ128A (X34: IC303)

Pin No. Pin Name

1 DC_ERR IC2

2 LINE_MUTE DC-CN I LINE MUTE detection

3,4 NC NC I 5 PORTGND0 µCOM

8 9 10,11 NC O 12~14 NC NC O 15 NC O L: MUTE ON, H: MUTE OFF 16 NC O 17 NC NC O

19 20 MUTE_PRE MUTE O MUTE for PREOUT L: MUTE ON, H: Normal

AUDIO_SW1_A

AUDIO_SW1_B

AUDIO_SW2_A AUDIO_SW2_B

EEPROM_WRT

MUTE_AVOUT

Module

(physical) Table

Audio O

Audio O Audio O

EEPROM I Write detection at ROM correction

MUTE O MUTE for AVOUT L: MUTE ON, H: Normal

I/O Application

I DC offset detection Low at the detection

LX/NAVI1/SW3 (or TV) / AVIN1 audio switching (For main) LX/NAVI1/SW3 (or TV) / AVIN1 audio switching (For main) TV/AVIN1/AVIN2 audio switching (For sub) TV/AVIN1/AVIN2 audio switching (For sub)

Truth Value

Processing Operation Description

Normal: 1.6V, TEL MUTE: 1V or lower, NAVI MUTE: 2.5V or higher

q Refer to truth value table

w Refer to truth value table w Refer to truth value table

When writing to E2PROM from outside, Hi is input with a jig. (Common use SCL and SDA will stop operation) In other cases: Low (Pull-down)

DDX8017/8027/8027Y DDX8037/8047/8067

MICROCOMPUTER’S TERMINAL DESCRIPTION

Pin No. Pin Name

21 P_CON DC-CN O External amp power supply control On during STANDBY),

22 PORTVDD0 µCOM 23 EXT_CONT DC-CN O External amp control

24 ANT_CONT DC-CN O Power antenna control H: Antenna UP,

25 P_ON

26 PWIC_MUTE POWER-IC O POWER-IC MUTE control

27 PWIC_STBY POWER-IC O POWER-IC standby control H: POWER ON, L: POWER OFF 28 NC O 29 29 AUD_SDA IC2 30 30 AUD_SCL IC2 31 MUTE0 IC2 32 MUTE1 IC2 33 MUTE2 IC2

34 NAVI_FLAG IC2

35 MUTEC IC2 36 NC NC O 37 GND0 µCOM 38 CPUREG µCOM 39 VDD0 µCOM 40 RESET µCOM 41 MODE/VPP µCOM 42 FLASH_SI FLASH I Data input at flash write 42 SYS_MDATA to X14 I Data from system control µ-com 43 FLASH_SO FLASH O Data output at flash writing 43 SYS_SDATA to X14 O Data to system control µ-com 44 FLASH_CLK FLASH I CLK input at the flash writing 44 SYS_MCLK to X14 I Clock from system control µ-com

45 BU_DET DC-CN I Backup reduced electric power detection

46 DIR_CDTO 47 DIR_CDTI

EEPROM_SDA

EEPROM_SCL

Module

(physical) Table

Power supply

EEPROM I/O Data for EEPROM (ROM correction)

EEPROM I/O Clock for EEPROM (ROM correction)

VI VI VI VI

DSP BLOCK DSP BLOCK

I/O Application

SW5V→SW14V power supply ON/OFF control

I/O Data for IC2

I/O Clock for IC2

O MUTE for IC2 VI OUT0 L: MUTE ON, H: MUTE OFF O MUTE for IC2 VI OUT1 L: MUTE ON, H: MUTE OFF O MUTE for IC2 VI OUT2 L: MUTE ON, H: MUTE OFF

Monitoring whether NAVI interruption is L: No NAVI interruption

taking place H: NAVI interruption in progress

O MUTE for IC2 VI MUXC L: MUTE ON, H: MUTE OFF

I Input data for DIR

O Output data for DIR

Truth Value

Processing Operation Description

Hi: During POWER ON (Does not come

Low: During STANDBY or POWER OFF

Hi at FMAM selection→Antenna UP

In other cases Low→Antenna DOWN H: ON, L: Normal L: MUTE ON (At POWER, ACC OFF, STANDBY, momentary power down)

Low when 8.8V or higher. Hi when reduced electric power (8.8V or lower)

DDX8017/8027/8027Y DDX8037/8047/8067

MICROCOMPUTER’S TERMINAL DESCRIPTION

Pin No. Pin Name

48 DIR_CCLK 49,50 NC NC O 51 ADC_RST 52 DIR_RST 53 DAC_RST 54 DSP_RST 55 DIR_CS 56 DAC_CS 57 DIR_ERRF 58 DSP_SS 59 ADC_MUTE 60 PORT/VDD1 µCOM 61 DAC_MUTE 62~64 NC NC O 65 BM_SW 66 DSP_INFO 67,68 NC NC O 69 SYS_ON to X14 I 70,71 XT2, XT1 µCOM 72 GND2 µCOM 73,74 X1, X2 µCOM 75,76 NC NC 77 LX_RST LX_M O Hard to resetting to slave unit H: Reset, L: Normal 78 LX_MUTE LX_M I Muting request from slave unit H: Mute ON, L: Mute OFF 79 LX_REQ_M LX_M O Communication request to slave unit 80 LX_CON LX_M O Startup requests to slave unit H: Slave unit ON, L: Slave unit OFF 81 LX_REQ_S LX_M I Communication request from slave unit 82 NC NC O 83 TV_SREQ TV I Request from TV unit 84 TUN_SDA FST I/O F/E I2C data input/output terminal 85 NC NC O 86 TUN_SCL FST I/O F/E I2C clock output terminal (MAX 400kHz) 87,88 NC NC O 89 PWIC_BEEP POWER-IC O Beep output 90 SYS_MREQ to X14 I Request from system control µ-com 91 SYS_SREQ to X14 O Request to system control µ-com 92 PORTGND1 µCOM 93 DAC_CLK 93 DSP_SCL

Module

(physical) Table

DSP BLOCK

DSP BLOCK DSP BLOCK DSP BLOCK DSP BLOCK DSP BLOCK DSP BLOCK DSP BLOCK DSP BLOCK DSP BLOCK

DSP BLOCK

DSP BLOCK DSP BLOCK

I/O Application

O Data clock for DIR

O Resetting for AD L: Reset O Resetting for DIR L: Reset O Resetting for DAC L: Reset O Resetting for DSP L: Reset O Chip select for DIR L: Select O Chip select for DAC L: Select

I S/PDIF Unlock H: Error, L: No Error O Select for DSP L: Select O MUTE for AD L: MUTE ON, H: MUTE OFF

O MUTE for DAC L: MUTE ON, H: MUTE OFF

O Bus management SW H: BM ON, L: BM OFF

ON/OFF control from system control µ-com

O Communication clock for DAC O Communication clock for DSP

Truth Value

Processing Operation Description

H: Box unit ON, L: Box unit OFF

DDX8017/8027/8027Y DDX8037/8047/8067

MICROCOMPUTER’S TERMINAL DESCRIPTION

Pin No. Pin Name

94 DAC_DO 94 DSP_SO 95 DAC_DI 95 DSP_SI 96 FSEL_1 97 FSEL_2 98 NC NC O

99 VSYNC_SW2 Visual O Switching for monitoring whether there is !4

100 TYPE4 TYPE I u Refer to truth value table 101 TV_CON TV O Start up request to TV unit H: TV unit ON, L: TV unit OFF 102 PORTVDD2 µCOM 103 TV_CLK TV O Clock to TV unit 104 TV_MREQ TV O Request to TV unit 105 TV_MDATA TV O Data to TV unit 106 TV_SDATA TV I Data from TV unit 107 LX_DATA_S LX_M I Data from slave unit 108 LX_DATA_M LX_M O Data to slave unit 109 LX_CLK LX_M I/O LX BUS clock 110 111 NAVI1_RX NAVI I Data from navigation 1 112 NAVI1_TX NAVI O Data to navigation 1 113 VISUAL_SW4 Visual O TV/Rear view camera video switching !2 Refer to truth value table 114 RGB_SW Visual O TV/NAVI1/NAVI2 RGB video switching !0 Refer to truth value table 115 TV_JUDGE TV I TV tuner old/new identification H: Old, L: New

116 VSYNC_SW1 Visual O Switching for monitoring whether there is !4

117,118 NC O 119

120 VSYNC_DET Visual I

121 122 123

124

125 RDS_CLK RDS I RDS decoder CLK input

VISUAL_SW5_1

VISUAL_SW3_2

VISUAL_SW3_1 VISUAL_SW2_2 VISUAL_SW2_1

VISUAL_SW1_2

Module

(physical) Table

DSP BLOCK DSP BLOCK DSP BLOCK DSP BLOCK DSP BLOCK DSP BLOCK

Visual O TV/AVIN1 video switching !3 Refer to truth value table

Visual O NAVI1/NAVI2/AVIN2 video switching !1 Refer to truth value table

Visual O NAVI1/NAVI2/AVIN1 video switching !1 Refer to truth value table Visual O SW5 (or TV)/AVIN2/DVD video switching o Refer to truth value table Visual O SW5 (or TV)/AVIN2/DVD video switching o Refer to truth value table

Visual O

I/O Application

ICommunication data for DAC

I Communication data for DSP OCommunication data for DAC O Communication data for DSP OFrequency selection for DC/DC OFrequency selection for DC/DC

NTSC/PAL identification COMP signal

AUTO detection COMP signal or not

NTSC/PAL identification COMP signal

AUTO detection COMP signal or not

Vertical synchronization signal detection (For AVIN2 automatic detection)

AVIN2/SW5 (or TV)/ SW3 (or NAVI1) video switching

Truth Value

i Refer to truth value table

Processing Operation Description

DDX8017/8027/8027Y DDX8037/8047/8067

MICROCOMPUTER’S TERMINAL DESCRIPTION

Pin No. Pin Name

126

127 128 VDD1 µCOM 129 RDS_DATA RDS I RDS decoder DATA input 130 RDS_QUAL RDS I RDS decoder QUAL input SW5 (or TV)/AVIN1/DVD video switching 131 GND1 µCOM 132 P_ON_AM FST O AM power supply ON/OFF control H: ON (AM selected), L: Normal 133 RDS_AFS FST I/O Constant switching at noise detection 134 TYPE3 TYPE I Destination setting u Refer to truth value table 135 RDS_NOISE FST I FM noise detection 136 137 138 TYPE0 OEM I Destination setting u Refer to truth value table 139 TYPE1 OEM I Destination setting u Refer to truth value table 140 TYPE2 Type I Destination setting u Refer to truth value table 141 OEM_TYPE0 Type I OEM destination setting y Refer to truth value table 142 OEM_TYPE1 Type I OEM destination setting y Refer to truth value table 143 ADCVDD µCOM 144 ADCGND µCOM

VISUAL_SW1_1

VISUAL_SW5_2

TUN_SMETER TUN_IFC_OUT

Module

(physical) Table

Visual O

Visual O TV/AVIN1 video switching !3 Refer to truth value table

FST I S-meter input FST I F/E IFC OUT input terminal H: With station, L: Without station

I/O Application

AVIN2/SW5 (or TV)/ SW3 (or NAVI1) video switching

Truth Value

i Refer to truth value table

Processing Operation Description

q Audio Selector 1 (TC4052BFT)

AUDIO_SW1_A AUDIO_SW1_B Output

LLIN3 AVIN1 HLIN2 TV LHIN1 AVIN2 HHIN0 LX

∗ Input is reversed by transistor before entering selector.

y Destination setting for OEM

Destination TYPE0 TYPE1

Marketing 0 0

OEM1 0 1 OEM2 1 0

EU Installation 1 1

w Audio Selector 2 (TC4052BFT)

AUDIO_SW2_A AUDIO_SW2_B Output

LLIN3 AVIN2 HLIN2 AVIN1 LHIN1 TV HHIN0 Not used

∗ Input is reversed b y transistor before entering selector.

DDX8017/8027/8027Y DDX8037/8047/8067

MICROCOMPUTER’S TERMINAL DESCRIPTION

u TYPE4, TYPE3, TYPE2, TYPE1, TYPE0

Category Model Destination TYPE4 TYPE3 TYPE2 TYPE1 TYPE0

1DIN KVT-817DVD K Reserve 0 0 0 1

KVT-827DVD E Reserve 0 0 1 0 KVT-837DVD M Reserve 0 0 1 1 KVT-867DVD V Reserve 0 1 0 0 KVT-847DVD X Reserve 0 1 0 1 KVT-727DVD E2 Reserve 0 1 1 0 KVT-747DVD R Reserve 0 1 1 1

2DIN DDX8017 K Reserve 1 0 0 1

DDX8027 E Reserve 1 0 1 0 DDX8037 M Reserve 1 0 1 1 DDX8067 V Reserve 1 1 0 0 DDX8047 X Reserve 1 1 0 1

∗ Reserve terminal is pulled down.

i Video Selector 1 (MM1228XFBE)

VISUAL_SW1_1 VISUAL_SW1_2 Output

LLIN1 AVIN1

HLIN2 SW4

L/H H IN3

o Video Selector 2 (MM1228XFBE)

VISUAL_SW2_1 VISUAL_SW2_2 Output

LLIN1 AVIN1

HLIN2 SW5 (or TV)

L/H H IN3 DVD

!0 RGB_SW (MM1503 or MM1508)

RGB_SW Output

L IN1 NAVI

H IN2 TV

!1 Video Selector 3 (BA7652AF)

VISUAL_SW3_1 VISUAL_SW3_2 Output

LLIN1 NAVI

HLIN2 AVIN2

LHIN3 Not used

HHMUTE -

!2 Video Selector 4 (MM1503)

VISUAL_SW4 Output

L IN1 TV

H IN2 Rear view

SW3 (or NAVI)

!3 Video Selector 5 (BA7652AF)

VISUAL_SW5_1 VISUAL_SW5_2 Output

LLIN1 TV

HLIN2 AVIN2

LHIN3 Not used

HHMUTE -

!4 VSYNC Selector (BA7652AF)

VSYNC_SW1 VSYNC_SW2 Output

LLIN1 AVIN2

HLIN2 CAMERA

LHIN3 AVIN1

HHMUTE -

About muting of composite signal to X14

• Video Selector 1 is set to SW3 and Video Selector 3 is set to MUTE. Mute timing is at full OSD.

DDX8017/8027/8027Y DDX8037/8047/8067

MICROCOMPUTER’S TERMINAL DESCRIPTION

● Disc Controller Microcomputer: MN103S71F (X37: IC4)

Pin No. Pin Name I/O Application

1 SW_2 I 2 SW_3 I Lo-START detection 3 CDON O CD-LD ON 4 VDD3 - VDD (3.3V) 5 VSS - VSS 6FGIMotor FG input 7 SW_4 I Lo-END detection 8,9 FADR17,18 O Address output to FLASH 10 FADR11 O Address output to FLASH 11 FADR9 O Address output to FLASH 12 VDD15 - VDD (1.5V) 13 FADR8 O Address output to FLASH 14,15 FADR13,14 O Address output to FLASH 16 NWE O Right signal output to FLASH 17,18 FADR16,15 O Address output to FLASH 19 DRAMVDD15 - DRAM power supply (1.5V) 20 DRAMVSS - VSS for DRAM 21 VSS - VSS 22 FADR12 O Address output to FLASH 23~30 FADR7~0 O Address output to FLASH 31 VSS - VSS 32 VDD3 - VDD (3.3V) 33~40 FDT0~7 I/O Data input/output with FLASH 41 NCE O 42 FADR10 O Address output to FLASH 43 NOE O Read signal output to FLASH 44 MMOD I Test mode switching signal 45 NRST I Reset input 46 VSS - VSS 47 SCLOCK I/O Dwire clock terminal 48 SDATA I/O Dwire data terminal

49 TxD/EXTRG0 I/O

50 RxD/EXTRG1 I/O

51 VDD3 - VDD (3.3V) 52 OSCI I 53 OSCO O 54 VSS - VSS

8cm Ej-STOP, Lo-START detection

Chip select signal output to FLASH

Serial transmission/ Dwire trigger terminal Serial reception/ Dwire trigger terminal

Oscillation input (16.897849MHz) Oscillation output (16.897849MHz)

Pin No. Pin Name I/O Application

55 OFS_TE O CD TE offset cancel output 56 DRV1 O Drive output for spindle drive 57 DRV2 O 58 DVDON O DVD-LD ON 59 STEP_A O Thread control output A 60 STEP_B O Thread control output B 61 Lo/Ej O Lo/Ej control terminal 62 LO.MUTE O Lo/Ej mute terminal 63 VSS - VSS 64 DRV.MUTE O Driver mute control 65 BMS O Spindle short brake control 66 LIM-SW I LIM-SW detection 67 Gain_SW O PDIC Gain switching 68 FEPCK O FEP clock output 69 FEPDT O FEP data output 70 FEPEN O FEP enable signal 71 DRAMVSS - VSS for DRAM 72 DRAMVDD15 - DRAM power supply (1.5V) 73 DRAMVDD33 - DRAM power supply (3.3V) 74 VDD3 - VDD (3.3V) 75 FG I Motor FG input 76 TX O Output for digital OUT 77 VDD15 - VDD (1.5V) 78 VSS - VSS 79 TSTSG O EQ calibration signal 80 VFOSHORT O Not used. 81 JLINE O J-line setting output 82 BDO I Dropout signal input 83 OFTR I Off-track signal input 84 AVSSD - VSS for analog 85 ROUT O MASH Rch audio output 86 LOUT O MASH Lch audio output 87 AVDDD - VDD (3.3V) for analog 88 VCOF I JFVCO control voltage 89 TRCRS I 90 AVDDC - VDD (3.3V) for analog 91 WBLIN I WBL input 92 CSLFLT I Not used 93 RFDIF I Not used

Focus balance adjustment output

Track loss generation signal input

DDX8017/8027/8027Y DDX8037/8047/8067

MICROCOMPUTER’S TERMINAL DESCRIPTION

Pin No. Pin Name I/O Application

94 AVSSC - VSS for analog 95 PLFLT2 I Condenser 2 for PLL 96 PLFLT1 I Condenser 1 for PLL 97 AVSSB - VSS for analog 98 ARF I Equivalent RF+ input 99 NARF I Equivalent RF- input 100 VHALF I Reference voltage 1.65V input

101 RV1 I

102 VREFH I Reference voltage 2.2V input 103 DSLF2 I Condenser 2 for DSL 104 DSLF1 I Condenser 1 for DSL 105 AVDDB - VDD (3.3V) for analog 106 JITOUT O For jitter monitor 107 AVDDA - VDD (3.3V) for analog 108 TECAPA I Not used 109 AD0 (FE) I FE input 110 AD2 (AS) I AS input 111 AD1 (TE) I TEph/TE3b input 112 AD3 (ENV) I RF envelop input 113 114 AD5 I Focus drive AD input 115 AD6 I Tracking drive AD input 116 AD7 (IOP) I 117 118 AVSSA - VSS for analog 119 PWM0 (FOD) O Focus drive output 120 PWM1 (TRD) O Tracking drive output 121 VSS - VSS 122 VDD3 - VDD (3.3V) 123 IDGT O Not used 124 DTRD O Not used 125 MONI0 O Internal monitor signal 126~130 131 SW_2∗3I 132 SW_1∗5I12cm Ej-STOP detection 133 DMARQ O DMA request output ATAPI host 134 NIOWR I ATAPI host write signal input 135 VDD3 - VDD (3.3V) 136 VSS - VSS

AD4 (RFDIFO)

AD8 (TEMP_DET)

MONI1~5 O Internal monitor signal

VREFH register for reference current power supply

I Push-pull TE input

Laser diode current measurement

ITemperature monitoring input

8cm Ej-STOP, Lo-START detection

Pin No. Pin Name I/O Application

137 NIORD I ATAPI host read signal input 138 IORDY O Ready output to ATAPI host 139 NDMACK I 140 INTRQ O Interruption output to ATAPI host 141 NIOCS16 O Not used 142 DA1 I ATAPI host address signal input 143 NPDIAG I 144 DA0 I ATAPI host address signal input 145 VSS - VSS 146 VDD3 - VDD (3.3V) 147 DA2 I ATAPI host address signal input 148 NCS1FX I 149 NCS3FX I 150 NDASP O ATAPI drive active/slave 151 HDD15 I/O ATAPI data input/output 152 HDD0 I/O ATAPI data input/output 153 HDD14 I/O ATAPI data input/output 154 HDD1 I/O ATAPI data input/output 155 HDD13 I/O ATAPI data input/output 156 VDD3 - VDD (3.3V) 157 VDD15 - VDD (1.5V) 158 VSS - VSS 159 HDD2 I/O ATAPI data input/output 160 HDD12 I/O ATAPI data input/output 161 HDD3 I/O ATAPI data input/output 162 HDD11 I/O ATAPI data input/output 163 HDD4 I/O ATAPI data input/output 164 HDD10 I/O ATAPI data input/output 165 HDD5 I/O ATAPI data input/output 166 VSS - VSS 167 VDD3 - VDD (3.3V) 168 HDD9 I/O ATAPI data input/output 169 HDD6 I/O ATAPI data input/output 170 HDD8 I/O ATAPI data input/output 171 HDD7 I/O ATAPI data input/output 172 VDDH - 5V reference power supply 173 NRESET I ATAPI reset signal input 174 MASTER I ATAPI master/slave signal input 175 SCL O EEPROM clock output 176 SDA I/O EEPROM data input/output

ATAPI host DMA acknowledge input

Diagnosis from ATAPI slave to master

ATAPI host chip select signal input ATAPI host chip select signal input

DDX8017/8027/8027Y DDX8037/8047/8067

TEST MODE

Operation Specifications

● Compatible Models for This Test Mode Specification

1Din GRA 1Din OSD 2Din GRA 2Din OSD M707 DSP Exist DSP Exist DSP None DSP Exist DSP None DSP None

K KVT-817DVD - KVT-717DVD DDX8017 DDX7017 KVT-M707 R- -KVT-747DVD - DDX7047 E KVT-827DVD KVT-727DVD KVT-627DVD DDX8027 DDX6027 KVT-M707

M KVT-837DVD - KVT-737DVD DDX8037 DDX7037 -

X KVT-847DVD - KVT-747DVD DDX8047 DDX7047 V KVT-867DVD - KVT-767DVD DDX8067 DDX7067 -

• Depending on Din/Display Types in the table below, test mode specifications may differ from model to model. In this specification, categorizing by 1DIN/2DIN and Graphic/OSD, M707, DSP, and destinations (K/R/E/M/X/V).

Model Din Type DSP Display Type

KVT-8x7DVD 1DIN Exist Graphic KVT-727DVD 1DIN Exist OSD KVT-7x7/627DVD 1DIN None OSD DDX80x7 2DIN Exist Graphic DDX70x7/6027 2DIN None OSD KVT-M707 1DIN None OSD

x: Different in accordance with the region code

● How to enter the test mode

There are two different ways to enter the test mode as shown below.

1) While pressing [SRC ke y + ATT k ey] at the same time, reset

the unit.

2) Connect to Lx connector odd jigging for writing regions

(2DIN: When adjusting flicker) Note1: The jig setting is arbitrary. Note that, how e ver, there are functions according the setting SW. (Region/Serial/Security/CPPM) Note2: In the test mode, power supply is cut off after 30 minutes. (This is for making the operation possible without Security input even when the security is On.)

● Adjustment items

Items to be adjusted after writing on the EEPROM on which regions have been written. As for the details of the adjustments, ref er to each adjustment item.

• Service Information/Serial Code writing

• Chroma adjustment

• Writing Touch Adjust values

• Screen position adjustment

• Panel mechanism position adjustment

• Writing Security Code (Other than K/R desinations)

● How to clear the Security Code

In adjusting K/R destination units, if the unit starts up with Security ON, the Security Code can be cleared in the following manner. (Other than in Test Mode)

1)In the e Security ON condition, after resetting or turning power ON after backup OFF, then the session starts with Security Code Input screen.

2)With the attached remote control in the Audio SW selected condition, input the code with the following procedure. Procedure 1: “K” input (Press Tenkey [5] 2 times) Procedure 2: “C” input (Press Tenkey [2] 3 times) Procedure 3: “A” input (Press Tenkey [2] once) Procedure 4: “Q” input (Press Tenkey [7] 2 times)

Note: If a remote controller other than the attached is used, Pressing Tenkey [7] twice will cause “R” to be input. If a mistake is made during Procedure 1~4 above, input other remote controller Key. Then, start inputting again from Procedure 1.

3)Security Code is complete when the input screen for the Security Code is cleared.

+ 84 hidden pages