Kenwood DDX419BT, DDX419BTM, DDX4019BT Instruction Manual
MONITOR WITH DVD RECEIVER
INSTRUCTION MANUAL
DDX419BT (Region 3 – DVD Region Code 3 Area)
DDX419BTM (Region 2 – DVD Region Code 2 Area)
DDX4019BT (Region 4 – DVD Region Code 4 Area)
This instruction manual is used to describe the models listed above. Model availability and features (functions)
may differ depending on the country and sales area.
ENGLISH
© 2018 JVC KENWOOD Corporation
B5A-2608-00 (MN/M2N/XN/A9N)
Important NoticeImportant Notice
To ensure proper use, please read through this
manual before using this product. It is especially
important that you read and observe WARNINGS
and CAUTIONS in this manual.
Please keep the manual in a safe and accessible
place for future reference.
WARNINGS
To prevent accidents and damages
• DO NOT install any unit or wire any cable in a
location where;
– it may obstruct the steering wheel and gearshift
lever operations.
– it may obstruct the operation of safety devices such
as air bags.
– it may obstruct visibility.
• DO NOT raise the volume level too much, as this will
make driving dangerous by blocking outside sounds,
and may cause hearing loss.
• DO NOT operate the unit while driving. If you need
to operate the unit while driving, be sure to look
around carefully.
• Stop the car before performing any complicated
operations.
• The driver must not watch the monitor while driving.
CAUTIONS
To care for the unit
• If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.
To care for the monitor
• The monitor built into this unit has been produced
with high precision, but it may have some ineffective
dots. This is inevitable and is not considered
defective.
• Do not expose the monitor to direct sunlight.
• Do not operate the touch panel using a ball-point
pen or similar tool with a sharp tip.
Touch the keys on the touch panel with your finger
directly (if you are wearing a glove, take it off).
• When the temperature is very cold or very hot...
– Chemical changes occur inside, causing
malfunction.
– Pictures may not appear clearly or may move
slowly. Pictures may not be synchronized with
the sound or picture quality may decline in such
environments.
On the volume setting
• Digital devices produce very little noise compared
with other sources. Lower the volume before playing
these digital sources to avoid damaging the speakers
by sudden increase of the output level.
The marking of products using lasers
The label is attached to the chassis/case and says
that the component uses laser beams that have been
classified as Class 1. It means that the unit is utilizing
laser beams that are of a weaker class. There is no
danger of hazardous radiation outside the unit.
ENGLISHi
Important NoticeImportant Notice
For Turkey
Bu ürün 28300 sayılı Resmi Gazete’de yayımlanan Atik
Elektrikli ve Elektronik Eşyalarin Kontrolü Yönetmeliğe
uygun olarak üretilmiştir.
Eski Elektrik ve Elektronik Ekipmanların İmha
Edilmesi Hakkında Bilgi (ayrı atık toplama
sistemlerini kullanan ülkeleri için uygulanabilir)
Sembollü (üzerinde çarpı işareti olan
çöp kutusu) ürünler ev atıkları olarak
atılamaz. Eski elektrik ve elektronik
ekipmanlar, bu ürünleri ve ürün atıklarını
geri dönüştürebilecek bir tesiste
değerlendirilmelidir. Yaşadığınız bölgeye
en yakın geri dönüşüm tesisinin yerini
öğrenmek için yerel makamlara müracaat
edin. Uygun geri dönüşüm ve atık
imha yöntemi sağlığımız ve çevremiz
üzerindeki zararlı etkileri önlerken
kaynakların korunmasına da yardımcı
olacaktır.
For DDX419BTM:
Declaration of Conformity with regard to the
RE Directive 2014/53/EU
Declaration of Conformity with regard to the
RoHS Directive 2011/65/EU
Manufacturer:
JVC KENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi,
Kanagawa, 221-0022, Japan
EU Representative:
JVCKENWOOD Europe B.V.
Amsterdamseweg 37, 1422 AC UITHOORN,
THE NETHERLANDS
English
Hereby, JVCKENWOOD declares that the radio
equipment “DDX419BTM” is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity is
available at the following internet address:
http://www.kenwood.com/cs/ce/eudoc/
Turkish
Burada, JVCKENWOOD “DDX419BTM” radyo
ekipmanının 2014/53/AB Direktifine uygun olduğunu
bildirir.
AB uyumluluk deklarasyonunun tam metni aşağıdaki
internet adresinde mevcuttur.
http://www.kenwood.com/cs/ce/eudoc/
ENGLISH ii
About this manual
ContentsContents
The displays and panels shown in this manual are
examples used to provide clear explanations of the
operations. For this reason, they may be different
from the actual displays or panels.
Illustrations of DDX419BT are mainly used for
explanation.
This manual mainly explains operations using the
buttons on the monitor panel and keys on the
touch panel. For operations using the remote
controller, see page37.
< > indicates the various screens/menus/
operations/settings that appear on the touch
panel.
[ ] indicates the keys on the touch panel.
Indication language: English indications are used
for the purpose of explanation. You can select the
indication language from the <Setup> menu.
(Page28)
Component Names and Operations ...............3
Basic Operations .................................................4
How to reset your unit .................................................................4
Turning on the power ..................................................................4
Turning off the power ..................................................................4
Putting the unit in standby .......................................................4
Turning off the screen ..................................................................4
Adjusting the volume ...................................................................4
Attenuating the sound ................................................................4
Getting Started ...................................................5
Initial settings .....................................................................................5
Registering a security code .......................................................5
Clock settings .....................................................................................6
Various Screens and Operations .....................6
Home screen ...................................................................................... 6
Source control screen ...................................................................7
List/setting screen...........................................................................8
Disc ........................................................................ 9
Video ...................................................................11
USB ......................................................................13
Android...............................................................14
iPod/iPhone .......................................................15
Radio ...................................................................16
Spotify ................................................................18
Other External Components ..........................20
AV-IN .....................................................................................................20
Using camera ................................................................................. 21
Using an external navigation unit ...................................... 21
Bluetooth® .........................................................22
Information ...................................................................................... 22
Preparation ....................................................................................... 22
Connection.......................................................................................22
Bluetooth mobile phone ......................................................... 24
Bluetooth audio player .............................................................26
KENWOOD Music Mix ............................................................ 26
Bluetooth settings .......................................................................27
Settings ..............................................................28
Audio settings ................................................................................28
Display settings ..............................................................................31
Input settings .................................................................................. 33
System settings..............................................................................34
Remote Controller ............................................37
Preparation ....................................................................................... 37
Basic operations for RC-DV340 (supplied) .................... 38
Basic operations for KNA-RCDV331 (optionally
purchased) ........................................................................................39
KENWOOD Remote APP ......................................................41
Installation and Connection ...........................41
Before installation ........................................................................41
Installing the unit..........................................................................43
Connecting external components .................................... 43
Wiring connection ....................................................................... 44
References .........................................................45
Maintenance ................................................................................... 45
More information ......................................................................... 45
Troubleshooting ...............................................48
Specifications ....................................................51
Trademarks and licenses .......................................................... 54
2
ENGLISH
Component Names and OperationsComponent Names and Operations
DDX419BT/DDX419BTM
1 Reset button
• Resets the unit.
2 Loading slot
3 Screen (touch panel)
4 Monitor panel
5 Built-in microphone*
• You can also connect an external microphone to
the unit (page 43). For details, contact the store
where you purchase this unit.
• See also <MIC SETUP> on page 28.
6 HOME button
• (Press): Turns on the power.
• (Hold): Turns off the power.
• HOME (Press): Displays the Home screen while
the power is on.
7 MENU/DISP OFF button
• MENU (Press): Pops up the short-cut menu.
• DISP OFF (Hold): Turns off the screen.
8 TEL/VOICE button
• TEL (Press): Displays the phone control screen.
• VOICE (Hold): Activates voice dialing.
9 Volume
p CAM/ATT button
* Only for DDX419BT.
DDX4019BT
1 Reset button
2 Loading slot
3 Screen (touch panel)
4 Monitor panel
5 HOME button
J/K buttons
• (Press): Adjusts the audio volume.
• CAM (Press): Displays the picture from the
connected camera.
• ATT (Hold): Attenuates the sound.
• Resets the unit.
• (Press): Turns on the power.
• (Hold): Turns off the power.
• HOME (Press): Displays the Home screen while
the power is on.
6 MENU/DISP OFF button
• MENU (Press): Pops up the short-cut menu.
• DISP OFF (Hold): Turns off the screen.
7 TEL/VOICE button
• TEL (Press): Displays the phone control screen.
• VOICE (Hold): Activates voice dialing.
8 Volume/ATT knob
• Volume (Turn): Adjusts the audio volume.
• ATT (Press): Attenuates the sound.
9 CAM button
• (Press): Displays the picture from the connected
camera.
ENGLISH
3
Basic OperationsBasic Operations
How to reset your unit
If the unit fails to operate properly, press the reset
button.
Turning on the power
Turning off the power
(Hold)
Putting the unit in standby
1 Display the source/option selection
screen.
On the Home screen, touch as follows:
2 Put the unit in standby.
On the source/option selection screen, touch as
follows:
Turning off the screen
On the monitor panel
(Hold)
To turn on the screen: Press DISP OFF on the
monitor panel or touch the screen.
On the pop-up short-cut menu
1 Display the pop-up short-cut menu.
2 On the pop-up short-cut menu, touch as
follows:
To turn on the screen: Touch the screen.
Adjusting the volume
DDX419BT/DDX419BTM
You can adjust the volume (00 to
35) by pressing J to increase and
pressing K to decrease.
• Holding J increases the volume
continuously to level 15.
DDX4019BT
You can adjust the volume (00
to 35) by turning the knob to the
right to increase and to the left to
decrease.
Attenuating the sound
DDX419BT/DDX419BTM
(Hold)
The ATT indicator lights up.
To cancel attenuation:
For DDX419BT/DDX419BTM: Press and hold the same
button again.
For DDX4019BT: Press the same button again.
DDX4019BT
4
ENGLISH
Getting StartedGetting Started
Initial settings
When you power on the unit for the first time or reset
the unit, the <Initial Setup> screen appears.
Perform the initial settings.
Initial Setup
Demonstration
Language
Front Camera
Rear Camera
User Customize
Viewing Angle
E.g. Initial settings screen for DDX419BT
Once completed, the Home screen appears.
ON
English
Enter
Enter
Enter
Enter
OFF
Finish
<Demonstration>
• ON (Initial): Activates the display demonstration.
• OFF: Deactivates the display demonstration.
<Language>
Select the text language used for on-screen
information.
• English (Initial)/Español/Français/Deutsch/
Italiano/Nederlands/Ελληνικά/Português/Türkçe/
Čeština/Polski/Magyar/Руccĸий/
/ /
/ / / /Bahasa
Malaysia/Bahasa Indonesia/
– For external monitors, only English/Spanish/
French/German/Italian/Dutch/Russian/Portuguese
are available. If another language has been
selected, the text language for external monitors
will be set to English.
• GUI Language (Local (the language selected above)
(Initial)/English): Selects the language used for
displaying operation keys and menu items.
<Front Camera> (Page33)
Make the settings to display the picture from the
connected front view camera.
<Rear Camera> (Page33)
Make the settings to display the picture from the
connected rear view camera.
<User Customize> (Page31)
Change the display design.
<Viewing Angle> (Page33)
Select the viewing angle in relation to the monitor to
make the image on the screen easier to see.
• Under 0° (Initial)/5°/10°/15°/20°
Registering a security code
1 Display the Home screen.
2 Display the <Security Code Set> screen.
On the Home screen, touch as follows:
Then, on the <Setup> screen, touch as follows:
[System] <Security Code> : [SET]
3 Enter a four-digit number (1), then
confirm the entry (
• To delete the last entry, touch [Clear].
• To cancel the setting, touch [Cancel].
2).
4 Repeat step 3 to confirm your security
code.
Now, your security code is registered.
ENGLISH
5
Getting StartedGetting Started
Various Screens and Various Screens and
To clear the registered security code: Touch [CLR]
for <Security Code> in step 2.
Then, enter the current security code to clear and
touch [Enter].
• When the unit has been reset or disconnected from
the battery, you are required to enter the security
code. Enter the correct security code, then touch
[Enter].
Clock settings
1 Display the Home screen.
2 Display the <Clock> screen.
On the Home screen, touch as follows:
Then, on the <Setup> screen, touch as follows:
[System] <Clock> : [Enter]
• You can also display the <Clock> screen by
touching the clock area on the Home screen.
3 Set the clock time.
Clock
Synchronize
E.g. Clock settings screen for DDX419BT
<Synchronize>
• Radio Data System (Initial)*1: Synchronizes the
clock time with FM RDS.
• NAV*2*3: Synchronizes the clock time with the
connected navigation unit.
• OFF: Sets the clock manually. Touch [J]/[K] to
adjust the hour, then minute.
– Touching [Reset] will set the minute to “00”.
*1 For Indonesian models, [OFF] is selected initially.
*2 Not applicable for Indonesian models.
*3 Appears only when a navigation unit is connected.
Radio Data System
AM10 28:
Reset
OperationsOperations
You can display or change to other screens at any time
to show information, change the AV source, change
the settings, etc.
Home screen
• You can customize the Home screen. (Page32)
• To display the Home screen from other screens, press
HOME.
Now
Playing
Touching the operation keys performs the following
actions:
1 Displays all playback sources and options.
2 Displays the <Setup> screen.
3 Displays the current playing source control screen.
4 Displays the <Clock> screen.
5 Selects or changes the playback source.
6
ENGLISH
Various Screens and OperationsVarious Screens and Operations
Available playback sources and options
Touch 1 to display the source/option selection screen.
Radio
BT Audio
Now
Playing
USB iPodDISC
TEL AV-IN
E.g. Source/option selection screen for DDX419BT
Touching the operation keys performs the following
actions:
[Radio] Switches to the radio broadcast.
[DISC] Plays a disc.
[USB] Plays files on a USB device.
[iPod] Plays an iPod/iPhone.
[Android™] Plays an Android device.
[BT Audio] Plays a Bluetooth audio player.
[TEL] Displays the phone control screen.
[AV-IN] Switches to an external component
connected to the AV-IN input
terminal.
[Spotify] Switches to the Spotify application.
[NAV]*1*2 Displays the navigation screen.
[STANDBY] Puts the unit in standby.
Android
TM
To change the page: Touch [
]/[ ]. Current page is
shown by the page indication on the top of the screen.
To return to the Home screen: Touch [ ] on the
source/option selection screen.
*1 Not applicable for Indonesian models.
*2 Selectable only when a navigation unit is connected.
Source control screen
You can perform the playback operation from the
source control screen during playback.
• The operation keys and information displayed vary
depending on the selected source/disc type/file type
being played.
• If the operation keys are not displayed on the screen,
touch the screen to show them.
E.g. Common audio playback source screen for
DDX419BT
1 Displays/hides short-cut source selection keys
2 Playback source or media type
3 Picture/artwork (shown if the file contains the
information)
4 Short-cut source selection keys
• Touching [
] on 1 to display the keys, or [ ]
to hide them.
5 Clock display
6 Track/file/song/video information
• Touching [<] scrolls the text if not all of the text
is shown.
7 Displays/hides other available operation keys*
8 Operation keys*
9 IN indicator (lights up while a disc is inserted)
p Playing time/playback status
q Playback mode indicator (Repeat/Random)
w File type indicator
e Current playback item information
(folder no./file no./track no./total track no./playback
file type)
* See the following “Common operation keys on source control
screen”.
7ENGLISH
Various Screens and OperationsVarious Screens and Operations
Common operation keys on source control screen
• The appearance of the operation keys may differ,
however the similar operation keys have the same
operations.
• Available operation keys differ depending on the
selected source or connected device.
Touching the operation keys performs the following
actions:
7
[ ]
][ ]
[
[
]
o]
[
[MODE] Displays the setting screen of the current
8
[ ]
[
]
S]/[T]
[
IW]
[
[
Displays other available operation keys
besides those shown on 8.
• To hide the window, touch [ ] .
Selects a folder.
Selects repeat playback mode.*
Stops playback.
playback source.
Displays the <Equalizer> screen.
Displays the folder list/track list/audio
menu/video menu.
• (Touch) Selects an item (chapter/
folder/track/audio file/video file).
• (Hold) Reverses/forwards search.
• (Hold) Plays in slow-motion while
paused for video playback.
Starts/pauses playback.
Selects random playback mode.*
]
* About playback mode:
– Available playback modes differ depending on the source, disc
type, connected device, etc.
– You cannot activate repeat playback mode and random
playback mode at the same time.
– To cancel the playback mode, touch repeatedly until the
indicator disappears.
Using the pop-up short-cut menu
While displaying the source control screen, you can
jump to another screen by touching the operation
keys on the pop-up short-cut menu.
1 Display the pop-up short-cut menu.
2 Select an item to jump to by touching as
follows.
[Eject] Ejects the disc from loading slot.
[Screen
Adjustment]
[Display OFF] Turns off the screen.
[Camera] Displays the picture from the
[SETUP] Displays the <Setup> screen.
[Current
Source]
To close the pop-up menu: Touch the screen
anywhere other than the pop-up short-cut menu.
Displays the picture adjustment
screen.
connected camera.
Displays the current source
control screen.
Using touch screen operation during
playback
Touching the areas performs the following actions:
1 Displays the video control menu while playing a
video.
2 While playing a video: Displays the source control
screen.
While playing an audio file: Displays the playback
operation keys.
3 Goes to the previous chapter/track.*
4 Goes to the next chapter/track.*
* Not available for video from an external component (AV-IN).
List/setting screen
Below are the common operation keys which appear
on the list/setting screen.
• The appearance of the operation keys may differ,
however the similar operation keys have the same
operations.
• Available operation keys differ depending on the
setting screens. Not all these operation keys are
shown on every screen.
8
ENGLISH
Various Screens and OperationsVarious Screens and Operations
DiscDisc
Touching the operation keys performs the following
actions:
1 Enters alphabet search* to list the items in
alphabetical order. When a keypad appears, touch
the first letter you want to search for.
• For “USB” source, you can switch between the
folder list and file list by touching [ ] or [ ] .
Then, touch [OK] to start searching.
2 Returns to the root folder.
3 Returns to the upper layer.
4 Closes the current screen.
5 Exits from the current screen or returns to the
previous screen.
6 Changes the page to display more items.
* Alphabet search is not available:
– For Android source
– When the playlist is selected
• If a disc does not have a disc menu, all tracks on it will
be played repeatedly until you change the source or
eject the disc.
• For playable disc types, file types and other
information, see pages45 and 46.
• If “ ” appears on the screen, the unit cannot accept
the operation you have tried to do.
– In some cases, without showing “ ”, operations
will not be accepted.
• When playing back a multi-channel encoded disc,
the multi-channel signals are downmixed.
Inserting a disc
Label side up
E.g. Inserting a disc for DDX419BT
The source changes to “DISC” and playback starts.
• The IN indicator lights up while a disc is inserted.
Ejecting a disc
1 Display the pop-up short-cut menu.
2 Eject the disc.
• When removing a disc, pull it out horizontally.
• You can eject a disc while playing another AV source.
• If the ejected disc is not removed within 15 seconds,
the disc is automatically inserted again into the
loading slot to protect it from dust.
Playback operations
Audio playback information and key
operation
• For playback information, see “Source control screen”
on page7.
• For key operations on the touch panel, see “Common
operation keys on source control screen” on
page8.
ENGLISH
9
DiscDisc
Selecting a folder/track on the list
1 Display the folder/track list.
On the source control screen, touch as follows:
2 Select the folder (1), then the item (2) in
the selected folder.
DISC
Folder Name 1
Folder Name 2
Folder Name 3
Folder Name 4
Folder Name 5
File Name 1
File Name 2
File Name 3
File Name 4
File Name 5
Select an item in each layer until you reach and
select the desired file.
Settings for disc playback
• Available items shown on the <DISC Mode> screen
differ depending on the type of disc/file being
played back.
1 Display the <DISC Mode> screen.
On the source control screen, touch as follows:
2 Make the settings.
DISC Mode
Menu Language
Subtitle Language
Audio Language
Dynamic Range Control
Down Mix
Screen Ratio
Dolby Surround
<Menu Language>*1
Select the initial disc menu language. (Initial:
English)
<Subtitle Language>*1
Select the initial subtitle language or turn subtitles
off (Off). (Initial: English)
<Audio Language>*1
Select the initial audio language. (Initial: English)
<Dynamic Range Control>
You can change the dynamic range while playing
Dolby Audio encoded discs.
• Wide: Reproduces powerful sound at a low
volume level with its full dynamic range.
• Normal: Reduces the dynamic range a little.
• Dialog (Initial): Reproduces movie dialog more
clearly.
English
English
English
SET
SET
SET
Dialog
Stereo
16:9
<Down Mix>
When playing back a multi-channel disc, this
setting affects the signals reproduced through the
front and/or rear speakers.
• Dolby Surround: Reproduces multi-channel
surround sound by connecting an amplifier
compatible with Dolby Surround.
• Stereo (Initial): Reproduces stereo playback
sound.
<Screen Ratio>
Select the monitor type to watch a wide screen
picture on the external monitor.
16:9 (Initial) 4:3 LB 4:3 PS
<File Type>*2
Select the playback file type when a disc contains
different types of files.
• Audio: Plays back audio files.
• Still image: Plays back still picture files.
• Video: Plays back video files.
• Audio&Video (Initial): Plays back audio files and
video files.
*1 For list of language codes, see page46.
*2 For playable file types, see page45.
If the disc contains no files of the selected type, the existing
files are played in the following priority: audio, video, then still
picture. You can change these settings only while playback is
stopped.
10 ENGLISH
VideoVideo
Playback operations
Video playback information on the source
control screen
E.g. Video playback source control screen for
DDX419BT
1 Media type
2 Playback status
3 Current playback item information
(title no./chapter no./folder no./file no./track no.)
4 Playing time
5 IN indicator (lights up while a disc is inserted)
6 Playback mode indicator (Repeat/Random)
7 File type indicator
Video menu control operations
You can display the video menu control during video
playback.
• Available operation keys differ depending on the
selected disc type and file type.
Video playback except VCD
Menu Control
E.g. Video menu control screen for DDX419BT
Touching the operation keys performs the following
actions:
1
[ZOOM]*1 Displays the picture size selection
screen.
1 Touch [ Zoom] to change the
magnification level of the picture
(Zoom1, Zoom2, Zoom3, Full:
Initial).
2 Touch [J] [K] [H] [I] to move the
zooming frame.
[Aspect] Displays the aspect ratio selection
screen.
Touch [
ratio.
<Full>*2: For 16:9 original pictures
4:3 signal 16:9 signal
<Just>: For viewing 4:3 pictures
naturally on the wide screen
4:3 signal 16:9 signal
<Normal>*2: For 4:3 original pictures
4:3 signal 16:9 signal
Aspect] to select the aspect
<Auto>: For “DISC” source and
“USB” source only: The aspect ratio is
automatically selected to match the
incoming signals.
ENGLISH
11
VideoVideo
[Picture
Adjust]
[Audio] Selects the audio type.
[Subtitle] Selects the subtitle type.
[Angle] Selects the view angle.
*1 When [Aspect] is set to <Just> or <Auto>, the picture is
zoomed with the aspect ratio of the <Full> setting.
This feature may not be used for some video sources.
*2 While DivX is played back with <Screen Ratio> set to [16:9]
(Page10 for discs/Page14 for USB), the aspect ratio may
not be set correctly.
Displays the picture adjustment screen.
1 Touch [DIM ON] or [DIM OFF] to
turn on or off the dimmer.
2 Touch [+]/[–] to adjust the other
items.
• <Bright>: Adjusts the brightness
(−15 to +15).
• <Contrast>: Adjusts the contrast
(−10 to +10).
• <Black>: Adjusts the blackness
(−10 to +10).
• <Color>: Adjusts the color
(−10 to +10).
• <Tint>: Adjusts the tint (−10 to +10).
• <Sharpness>: Adjusts the sharpness
(−2 to +2).
2
[ MENU]
[T MENU] Displays the disc menu (DVD).
[Highlight] Switches to the direct disc menu mode.
[CUR] Displays the menu/scene selection
Video playback for VCD
E.g. Video menu control screen for DDX419BT
Displays the disc menu (DVD).
Touch the target item to select.
screen.
• [
J] [K] [H] [I]: Selects an item.
• [Enter]: Confirms the selection.
• [Return]: Returns to the previous
screen.
Menu Control
Touching the operation keys performs the following
actions:
1
[ZOOM]
[Aspect]
[Picture
Adjust]
2
[ MENU]
[Audio] Selects the audio channel
[Direct]* Displays or hides the direct selection
[Return] Displays the previous screen or menu.
* You need to stop playback to deactivate the PBC function when
playing a VCD with PBC activated.
Refer to “Video playback except VCD” on
page11.
Displays the disc menu.
(ST: stereo, L: left, R: right).
keys.
1 Touch [DIR/CLR] to select a track
directly on a VCD.
2 Touch the numbers ([0], [1] to [9]) to
select the desired track.
3 Touch [Enter] to confirm.
To delete the last entry, touch [DIR/
CLR].
12 ENGLISH
USBUSB
You can connect a USB mass storage class device such
as a USB memory, digital audio player, etc. to the unit.
• For playable file types and other information, see
pages45 and47.
• You cannot connect a PC or portable HDD to the
USB input terminal.
• You cannot connect a USB device via a USB hub.
Connecting a USB device
USB device* (commercially available)
Rear panel
The source changes to “USB” and playback starts.
• All tracks in the USB device will be played repeatedly
until you change the source or disconnect the USB
device.
* Use CA-U1EX for extending the cable if necessary. (Max 500 mA,
5V)
Playback operations
Playback information and key operation
• For playback information, see “Source control screen”
on page7.
• For key operations on the touch panel, see “Common
operation keys on source control screen” on
page8.
Selecting the file type to play
You can specify the file type to play.
USB
File type Audio
E.g. USB source control screen for DDX419BT
Select the file type as follows:
[Audio] Plays back audio files.
[Video] Plays back video files.
[Photo] Plays back still picture files.
If the USB device contains no files of the selected type,
the existing files are played in the following priority:
audio, video, then still picture. You can change these
settings only while playback is stopped.
Selecting a folder/track on the list
1 Display the folder/track list.
On the source control screen, touch as follows:
2 Select the folder (1), then the item (2) in
the selected folder.
USB
Folder Name 1
Folder Name 2
Folder Name 3
Folder Name 4
Folder Name 5
E.g. USB list screen for DDX419BT
Select an item in each layer until you reach and
select the desired file.
File Name 1
File Name 2
File Name 3
File Name 4
File Name 5
Selecting a folder/track using alphabet
search
(Applicable only for audio file type)
You can search for a folder or an audio file by entering
the first letter you want to search for.
1 Select the list (folder or track) to search.
On USB list screen, touch as follows:
• [ ]: Folder list
• [ ]: Track list
ENGLISH
13
USBUSB
2
Enter the alphabet to search.
Touch the first letter you want to search for, then
touch [OK].
Settings for USB playback
1 Display the <USB Mode> screen.
On the source control screen, touch as follows:
AndroidAndroid
Connecting an Android device
This unit supports Android OS 4.1 and above.
Android (commercially available)
USB cable (commercially available)
Playback operations
Playback information and key operation
Android
HANDMODE
IWST
E.g. Android source control screen for DDX419BT
2 Make the settings.
USB Mode
Screen Ratio
Drive Select
<Screen Ratio>
Select the monitor type to watch a wide screen
picture on the external monitor.
16:9 (Initial) 4:3 LB 4:3 PS
<Drive Select>
• Next: Switch between internal memory and the
memory source of the connected device (such as
a mobile phone).
14
ENGLISH
16:9
Next
Rear panel
When connecting an Android device, “HAND MODE” is
shown. You can control Android device using a media
player application installed in the Android device.
Touching the operation keys performs the following
actions:
[S]/[T]
IW]
[
Selects an audio file.
Starts/pauses playback.
iPod/iPhoneiPod/iPhone
Connecting an iPod/iPhone
• For playable iPod/iPhone types and other
information, see page47.
• You cannot watch video.
Wired connection
iPod/iPhone
Lightning model
(commercially available)
USB Audio cable
for iPod/iPhone:
KCA-iP103 (optional
accessory)
ear panel
R
The source changes to “iPod” and playback starts.
iPod/iPhone 30-pin
connector model
(commercially available)
USB Audio cable
for iPod/iPhone:
KCA-iP102 (optional
accessory)
Bluetooth connection
Pair the iPod/iPhone with this unit via Bluetooth.
(Page22)
Selecting the playback device via the
connection method
See <Smartphone Setup> on page 34 for more
information.
Playback operations
Playback information and key operation
• For playback information, see “Source control screen”
on page7.
• For key operations on the touch panel, see “Common
operation keys on source control screen” on
page8.
Additional keys operations: Touching the operation
keys performs the following actions.
[ ]
Switches the device on the
<Smartphone Setup> screen.
(Page34)
Selecting an audio file from the menu
1 Display the audio menu.
On the source control screen, touch as follows:
2 Select a category (1), then select a
desired item (
iPod
Playlists
Artist
Album
Songs
Podcasts
Select an item in each layer until you reach and
select the desired file.
• Available categories differ depending on the type
of iPod/iPhone.
Settings for iPod/iPhone playback
2).
Artist 000000001
Artist 000000002
Artist 000000003
Artist 000000004
Artist 000000005
1 Display the <iPod Mode> screen.
On the source control screen, touch as follows:
2 Make the settings.
iPod Mode
Artwork
<Artwork>
• ON (Initial): Shows the artworks of the playing
files.
• OFF: Hides the artworks of the playing files.
ON OFF
ENGLISH
15
RadioRadio
Listening to the radio
The unit switches to FM alarm scene automatically
when receiving an alarm signal from FM broadcast.
Playback information on the source control
screen
Radio
1 Selects the band (AM/FM1/FM2/FM3)
2 Current station frequency/RDS status
3 Text information
• Touching [<] scrolls the text if not all of the text
is shown.
• Touching [Radio Text] switches the information
between Radio Text, Radio Text Plus and PTY
code.
4 Displays the preset stations window (Page17)
5 [P1] – [P5]
• (Touch) Selects a preset station.
• (Hold) Presets the current station.
6 Displays/hides other available operation keys*
7 NEWS indicator
8 AF indicator
9 TI indicator
p Operation keys*
q ST/MONO indicator
The ST indicator lights up when receiving an FM
stereo broadcast with sufficient signal strength.
w Seek mode indicator
e LO.S indicator
r RDS indicator
t EON indicator
The EON indicator lights up when a Radio Data
System station is sending EON signals.
* See the following “Operation keys on source control screen”.
Operation keys on source control screen
• The appearance of the operation keys may differ,
however the similar operation keys have the same
operations.
• See also “Common operation keys on source control
screen” on page8.
Touching the operation keys performs the following
actions:
6
[AME ]
[MONO]*1 Activates monaural mode for better FM
(Hold) Presets stations automatically.
reception (stereo effect will be lost).
• The MONO indicator lights up while
monaural mode is activated.
• To deactivate, touch [MONO] again.
[TI]*1 (For FM RDS features)
Activates TI standby reception mode.
• When TI is activated, the unit is ready
to switch to traffic information if
available. The TI indicator lights up in
white.
• If the TI indicator lights up in orange,
tune into another station providing
Radio Data System signals.
• The volume adjustment for Traffic
Information is automatically
memorized. The next time the unit
switches to Traffic Information, the
volume is set to the memorized level.
• To deactivate, touch [TI] again.
[MODE]*1 Changes the settings for radio reception
on the <Radio Mode> screen.
p
[PTY]*1*2 (For FM RDS features)
[SEEK]
Enters PTY search mode.
1 Touch [PTY].
2 Touch and hold a PTY code to search
for.
If there is a station broadcasting a
program of the same PTY code as you
have selected, that station is tuned in.
Changes the seek mode for [
• AUTO1 (Initial): Auto search
• AUTO2: Tunes in preset stations one
after another
• MANU: Manual search
S]/[T].
16
ENGLISH
Loading...