DDX418
DDX4048BT
DDX318
DDX3048
MONITOR WITH DVD RECEIVER
INSTALLATION MANUAL
MONITEUR AVEC RÉCEPTEUR DVD
MANUEL D'INSTALLATION
MONITOR CON RECEPTOR DVD
MANUAL DE INSTALACIÓN
© 2010 Kenwood Corporation All Rights Reserved. |
LVT2199-005A (KN/RN) |
Accessories/ Installation Procedure
Accessories
1 5
..........1 |
..........1 |
2 |
6 |
..........1 (2m: 6.5 ft) |
..........2 |
3 |
7*1 |
..........6 |
..........1 (3m: 9.8 ft) |
4 |
*1 DDX418/ DDX4048BT |
|
only. |
..........6 |
|
Installation Procedure
1To prevent a short circuit, remove the key from the ignition and disconnect the - battery.
2Make the proper input and output wire connections for each unit.
3Connect the speaker wires of the wiring harness.
4Connect the wiring harness wires in the following order: ground, battery, ignition.
5Connect the wiring harness connector to the unit.
6Install the unit in your car.
7Reconnect the - battery.
8Press the reset button.
9Perform the Initial Setup. (Refer to the Instruction Manual.)
2 
DDX418/DDX4048BT/DDX318/DDX3048
2WARNING
•If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.
•Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow). The power supply must be connected to the wires via the fuse.
After the Installation
After the installation, perform the Initial Setup by referring to the instruction manual.
¤
•Mounting and wiring this product requires skills and experience. For best safety, leave the mounting and wiring work to professionals.
•Make sure to ground the unit to a negative 12V DC power supply.
•Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.
•Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage the unit.
•If the power is not turned ON ("Miswiring DC Offset Error", "Warning DC Offset Error" is
displayed), the speaker wire may have a shortcircuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked.
•If your car’s ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, such as with battery wires, the battery may be drained.
•If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening.
•If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace the old fuse with one with the same rating.
•Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals.
•Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car.
•When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal.
•After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.
•Mount the unit so that the mounting angle is 30° or less.
•Do not press hard on the panel surface when installing the unit to the vehicle. Otherwise scars, damage, or failure may result.
•This unit has the cooling fan to decrease the internal temperature. Do not mount the unit in a place where the cooling fan of the unit are
blocked. Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction.
Cooling fan
DDX418/ DDX4048BT only
•Install the Bluetooth adaptor (KS-UBT1) besides the place enclosed by the metal.
Bluetooth adaptor (KS-UBT1)
¤CAUTION
Install this unit in the console of your vehicle.
Do not touch the metal part of this unit during and shortly after the use of the unit. Metal part such as the heat sink and enclosure become hot.
English 
3
Connecting Wires to Terminals
Bluetooth Microphone (Accessory 7) |
|
DDX418/DDX4048BT only |
Purple/White |
(Reverse sensor wire) 
Connect to vehicle's reverse lamp harness when using the optional rear view camera.
Antenna Cord |
Light Green |
Extension cable (Accessory 2) |
|||||
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
(Parking sensor wire) |
|
||
|
|
|
|
|
|||
|
|
|
|
|
|||
FM/AM antenna input
Accessory 1
For best safety, be sure to connect the parking sensor.
⁄ Connect to the vehicle's parking
brake detection switch harness. FUSE ( 10A )
White + / White/black - : To front speaker (left)
Gray + / Gray/black - : To front speaker (right)
Green + / Green/black - : To rear speaker (left)
Purple + / Purple/black - : To rear speaker (right)
If no connections are made, do not let the cable come out from the tab.
Blue
(Antenna control wire)
Blue/White
(Power control wire)
Brown
(Mute control wire)
Light blue/Yellow
(Steering remote control wire)
Orange/White
(Dimmer control wire)
Red (Ignition wire)
Yellow (Battery wire)
Black (Ground wire) - (To car chassis)
4 
DDX418/DDX4048BT/DDX318/DDX3048
Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna.
When using the optional power amplifier, connect to its power control terminal.
To the terminal that is grounded when either the telephone rings or during conversation. (To connect the Kenwood navigation system, consult your navigation manual.)
To use the steering wheel remote control feature, you need to an exclusive remote adapter (not supplied) matches your car is required.
To car light control switch
ACC |
|
|
|
|
|
Ignition key switch |
||||
|
|
|
|
|
|
|
|
|
|
Car fuse box |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
Car fuse box |
|
|
|
(Main fuse) |
|||||
|
|
|
|
|
|
|
|
|
|
Battery |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Connecting Other Products
Navigation System
(Optional Accessory)
⁄Navigation units that can be connected to this unit. (As of December, 2010):
•KNA-G610
•KNA-G630
For latest information, access the www.kenwood.com/cs/ce/.
Audio/Visual Output
•Visual output (Yellow)
•Audio output (3.5φ mini plug) Resistance-free stereo type mini plug
Rear View Camera Input
• Visual input (Yellow)
Connection cable (Included in the Navigation System)
USB terminal
Front Preout
•Audio left output (White)
•Audio right output (Red)
Rear/Subwoofer Preout switchable
•Audio left output (White)
•Audio right output (Red)
USB device (commercially available)
iPod
(commercially available)
CA-U1EX |
(Optional Accessory) |
KCA-iP22F
Audio Visual input (Optional Accessory) (iPod/AV Input switchable)
English 
5
Installation/Removing the Unit
Installing the Unit
Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place.
⁄
•Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip).
Installation on Toyota, Nissan or Mitsubishi Car using Brackets
Accessory 3 (M5x6mm) or Accessory 4 (M5x7mm)
Car Bracket
Accessory 3 (M5x6mm) or Accessory 4 (M5x7mm)
Installing the Escutcheon
1 Attach accessory 5 to the unit.
Accessory 5
Removing the Escutcheon
1Engage the catch pins on the removal tool 6 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure.
Accessory 6
Catch
Lock
⁄
•The frame can be removed from the top side in the same manner.
2When the lower level is removed, remove the upper two locations.
6 
DDX418/DDX4048BT/DDX318/DDX3048
Loading...