Kenmore Elite 79641483410, 79641482410 Owner’s Manual

Use & Care Guide

Manual de Uso y Cuidado

English / EspaEol

Model/Modeio: 796.4148 _

I<e

:kt :!,StS 3 6 ..... t: t; _ "

..... + ......... +

b_ lie ;t.

$ :::::::colo_ t'_ m'_ ;;_e% t Ometo de coR>_ +

IIII I I

MFL68639706

Sears Brands Management Corporation Hoffman Estates, JL 60179 U.S.A.

www.kenmore.com www.sears.com

IMPORTANT SAFETY INSTRUCTIONS ............................. 3-5

GROUNDING REQUIREMENTS.............................................5

FEATURES AND BENERTS

Key Parts and Components ................................................. 6

Included Accessories ........................................................... 6

Optional Accessories ........................................................... 6

INSTALLATION REQUIREMENTS

Key Dimensions and Specifications ................................... 7

Choose the Proper Location ............................................... 7

Flooring .................................................................................. 7

Clearances ............................................................................ 7

INSTALLATION INSTRUCTIONS

Unpacking and Removing Shipping Bolts ......................... 8

Connecting the Water Lines ................................................ 9

Connecting the Drain Hose ............................................... 10

Connect to the Power Supply ............................................. 10

Leveling the Washer ........................................................... 11

Installation of Non-Skid Pads (optional) ........................... 11

HOW TO USE

Control Panel Features ........................................................ 12

Operating the Washer ......................................................... 13

Cycle Guide .................................................................... 14-15

Sorting Wash Loads ............................................................ 16

About the Dispenser Drawer .............................................. 17

Detergent and Dispenser Use ............................................. 18

Time and Status Display .................................................... 19

Cycle Modifier Buttons ....................................................... 20

Option buttons ..................................................................... 21

Special Functions ................................................................ 22

CARE AND CLEANING

Regular Cleaning .......................................................... 23=24

Maintenance .................................................................. 25=26

Cleaning the Water Inlet Filters .................................... 25

Cleaning the Drain Pump Filter ..................................... 26

KENMORE CONNECT TM System.........................................27

TROUBLESHOOTING GUIDE

Normal Sounds You May Hear ......................................... 28

Before Calling for Service .......................................... 28-30

WARRANTY ............................................................................ 31

In the space below, record the date of purchase, model,

and serial number of your product. You will find the model and serial number printed on an identification plate located inside

the washer door. Have these items of information available whenever you contact Sears concerning your

product. Model No. Date of Purchase Serial No.

Save these instructions and your sales receipt for future reference.

Master Protection Agreements

Congratulations on making a smart purchase. Your new Kenmore Elite® product is designed and manufactured for years of dependable operation. But like all products, it may require preventive maintenance or repair from time to time. That's when having a Master Protection Agreement can save you money and aggravation.

The Master Protection Agreement atso helps extend the life of your new product. Here's what the Agreement s includes:

•Parts and labor needed to help keep products operating properly under normal use, not just defects. Our coverage goes well beyond the product warranty. No deductible, no functional failure excluded from coverage - real protection.

•Expert service by a force of more than 10,000 authorized Sears service technicians, which means

someone you can trust will be working on your product.

*Unlimited service calls and nationwide service, as

often as you want us, whenever you want us.

• "No-lemon" guarantee - replacement of your covered product if four or more product failures occur

within twelve months.

• Product replacement if your covered product can not be fixed.

*Annual Preventive Maintenance Check at your request

- no extra charge.

"Fast help by phone - we call it Rapid Resolution.

Phone support from a Sears representative on all products. Think of us as a "talking owner's manual."

"Power surge protection against electric damage due to

power fluctuations.

"$250 food lass protection annually for any food

spoilage that is the result of mechanical failure of any covered refrigerator or freezer.

"Rental reimbursement if repair of your covered

product takes longer than promised.

"25% discount off the regular price of any non-covered

repair service and related installed parts.

Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call at any time day or night or schedule a service appointment online.

The Master Protection Agreement is a risk-free purchase. If you cancel for any reason during the product warranty period, we will provide a full refund, or a prorated refund any time after the product warranty period expires. Purchase your Master Protection Agreement today!

Some limitations and exclusions apply. For prices and addltlonal information in the U.S.A.

call 1=800=827=6655. _Coverage in Canada varies an some items.

Far full detalis call Sears Canada at 1=800=361=6665. Sears Installatlan Service

For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in the U.S.A. or Canada call:

1-800-4-MY-HOME ®.

Therearemanyimportantsafety messages in this manual and on your appliance. Always read and obey

all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can result in property damage and/or serious bodily harm or death.

All safety messages will follow the safety alert symbol and either the word DANGER or WARNING.

These words mean:

!ndicates a hazardous situation which, if not avoided, will result in death or serious _njury.

!ndicates a hazardous situation which, if not avoided, could result in death or serious _njury.

All safety messages will tell you what the potential hazard is, tell you how to

reduce the chance of injury, and tell you what can happen if the instructions are not followed.

To reduce the risk of fire, electric shack, or injury to persons when using this appllance, fallow basic precautions, includlng the fallowing.

*Before use, the washer must be properly installed as

described in this manual.

*Do not wash artictes that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.

*Do not add gasoline, dry cleaning solvents, or other

flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

*Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been used for such a period, before using the washer, turn ON

all hot water faucets and let the water flow from each for several minutes. This will release any accumulated

hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.

*Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used near children.

*Before the washer is removed from service or

discarded, remove the door to prevent children from climbing inside.

*Do not install or store the washer where it will be

exposed to the weather or freezing temperatures.

*Do not tamper with controls. *Do not repair or replace any part of the washer or

attempt any servicing other than as described in this manual. We strongly recommend that any service be performed by a qualified technician.

*See Installation Instructions for grounding requirements. *ALWAYS follow the fabric care instructions supplied by

the garment manufacturer.

*Do not place items exposed to cooking oil in your

washer. Items contaminated with cooking oils may

contribute to a chemical reaction that could cause a load to catch fire.

*Use fabric softeners or products to eliminate static only

as recommended by the manufacturer.

*This washer is not designed for maritime use or for

mobile installations such as in RVs, aircraft, etc.

*Turn OFF the water faucets and unplug the washer if

the machine is to be left for an extended period of time, such as during vacations.

*Packaging material can be dangerous for children.

There is a risk of suffocation. Keep all packaging from children.

*Always check the inside of the washer for foreign

objects before loading laundry. Keep the door closed

when not in use.

*WARNING: This product contains chemicals known

to the State of California to cause cancer and birth

defects or other reproductive harm. Wash hands after

handling.

To reduce the risk of fire, electric shock, or injury to

persons when using this appliance, follow basic precautions, including the following.

*Unplug the washer before cleaning to avoid the risk of

electric shock.

*Never use harsh chemicals, abrasive cleaners, or

solvents to dean the washer. They will damage the finish.

*Do not put oily or greasy rags or clothing on top of

the washer. These substances give Off vapors that could ignite the materials.

*Do not wash items that are soiled with vegetable or

cooking oil. These items may contain some oil after

laundering and may catch fire.

*Disconnect this appliance from the power supply

before attempting any user maintenance. Turning the

controls to the OFF position does not disconnect this

appllance from the power supply. Failure to follow this

warning can cause serious injury, fire, electric shock, or death.

*Do not combine detergents, fabric softeners, and/or

other laundry products from different manufacturers for use in a load, unless specified on the fabric label.

*Do not mix chlorine bleach with ammonia or acids

such as vinegar. Follow package directions when using laundry products. Incorrect usage can produce

poisonous gas, resulting in serious injury or death.

*Do not reach into the washer while parts are moving.

Before loading, unloading, or adding items, push in the

cycle selector knob and allow the drum to coast to a complete stop before reaching inside. Failure to follow

this warning can cause serious injury, fire, electric shock or death.

*Refer to INSTALLATION INSTRUCTIONS for detalled

grounding procedures. Installation instructions are

packed in the washer for the instailer's reference. If the washer is moved to a new location, have it checked and reinstalled by a qualified service technician. Failure to fottow this warning can cause serious injury, fire, electric shock, or death.

*Do not, under any circumstances, cut or remove the

third (ground) prong from the power cord. Failure to follow thiswarning can cause serious injury, fire, electric shock, or death.

"For personal safety, this appliance must be properly

grounded. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

*The power cord of this appllance is equipped with a

3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility

of electric shock hazard from this appliance.

*This washer must be plugged into a 120VAC, 60Hz

grounded outlet. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

*Have the wall outlet and circuit checked by a

quailfied electrician to make sure the outlet is property grounded. Failure to follow this warning can cause

serious injury, fire, electric shock, or death.

*Where a standard 2-prong wail outlet is encountered,

it is your personal responslbiffty and obligation to

have it replaced with a property grounded 3-prong wall outlet. Failure to follow this warning can cause

serious injury, fire, electric shock, or death.

*Do not install on carpet, install the washer on a soild

floor. Failure to follow this warning can cause serious

leak damage.

*Do not remove grounding prong. Do not use an

adapter or extension cord. Plug into a grounded 3-prong outlet. Failure to follow these warnings can

cause serious injury, fire, electric shock, or death.

*The washer should always be plugged into its own

indlvldual electrical outlet which has a voltage rating that matches the rating plate. This provides the best

performance and atso prevents overloading house wiring circuits which could cause a fire hazard from

overheated wires.

*Never unplug your washer by pulllng on the power

cord. Always grip plug firmly and putt straight out from the outiet. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

* Immedlately repair or replace all power cords that

have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage

along its length or at either end. Consult with a qualified service technician. Failure to follow this warning can cause serious injury, fire, electric shock,

or death.

*When installlng or moving the washer, be careful not

to pinch, crush, or damage the power cord. Failure to follow this warning can cause serious injury, fire,

electric shock, or death.

*The washer must be installed and electrlcaffy

grounded by a quallfied service technician in accordance with local codes to prevent shock hazard and assure stability during operation.

*The washer is heavy. Two or more people may be

needed to install and move the appliance. Faiture to do so can result in damage to property or serious bodily injury.

*Store and install the washer where it will not be

exposed to temperatures below freezing or exposed

to outdoor weather conditions. Faiture to follow this warning can cause serious leak damage.

*To reduce the risk of electric shock, do not install

the washer in humid spaces. Failure to follow this warning can cause serious injury, fire, electric shock, or

death.

•Donotallowchildrento playonor inthewasher.Close

supervision of children is necessary when the washer is used near children. As children grow, teach them the proper, safe use of all appliances. Failure to comply with

these warnings could result in serious personal injury.

•Destroy the carton, plastic bag, and other packing materials after the washer is unpacked. Children might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers. Failure to comply with these warnings could result in serious personal injury.

•Keep laundry products out of children's reach. To prevent personal injury, observe all warnings on product labels. Failure to comply with these warnings

could result in serious personal injury.

•Before your washer is removed from service or

discarded, remove the door to the washing compartment to avoid the danger of children or small animals getting trapped inside. Failure to do so can result in serious personal injury or death.

IMPORTANT: Please read carefully. TO CONNECT ELECTRICITY

Improper connection of the equipment-grounding

conductor can result in risk of electric shock. Check with a qualified electrician or service technician

if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance. If it does not fit the outlet, have a proper outlet installed by a qualified electrician. Failure to follow these warnings can cause serious injury, fire, electric shock, or death.

3-prong grounding type

Ensure proper

ground exists

before use.

3-prong grounding

plug

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of

malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least

resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes

and ordinances.

KEY PARTS AND COMPONENTS

O ETERGENT DISPENSER

There are four compartments. One each for prewash, main wash, liquid bleach, and liquid fabric softener.

O ONTROL PANEL WITH LED DISPLAY

The easy-to-read LED display shows cycle options, settings, cycle status, and estimated time remaining during operation. NOTE: Sensors in the washer automatically detect the size of the wash load to optimize washing time, based on the selected cycle and options.

_ IRECT-DRIVE MOTOR

The direct-drive motor provides improved performance and reliability while increasing energy eftqciency. (Motor is not visible.)

O ARGE-CAPACITY STAINLESS STEEL DRUM

The ultra-large stainless steel drum otters extreme durability and is tilted to improve eff]ciency and allow easier access for large items.

O ASY-ACCESS LOCKING DOOR

The extra-large door locks during operation. The door

will not open until it is safe to do so.

_ ILTER ACCESS PANEL

Provides easy access to the drain pump filter, which allows you to clean the filter or retrieve lost items without a

service call. LEVELING FEET

Four leveling feet (two in the front and two in the back) adjust to improve washer stability on uneven floors. Feet are adjusted and locked in place using the adjusting

wrench included with the washer.

DOOR MAGNET

Safely and conveniently keeps the door ajar when the washer is not in use, to promote air circulation and allow the interior of the drum to dry. To use this feature, close the door gently until it just contacts the door magnet.

0 _ O = i

Cold and Hot Wafer Inlets

Power

Cord

Drain

Hose

included Accessories

Non-skid pads

(for covering shipping belt holes)

Wrench (for removing Tie Strap

shipping bolts and (for securing Bbow Bracket

adjusting and locking drain hose) (for securing

leveling feet) drain hose)

Wrench appearance may vary.

Caps (4)

Optional Accessories

Hot and Cold Water Hoses Drain Hose Extension

P/N 5215ER2002K

Pedestal Stacking kit (For dryer)

D26 17013 (Chrome Look)

51042 (White) 51043 (Metallic Silver)

KEY DiMENSiONS AND SPECiFiCATiONS

Description Front-Loading Washer Electrical Requirements 120 VAC, 60 Hz

Max. Water Pressure 14.5 - 142 PSi (100 - 980 kpa)

Dimensions 27" (W) x 293/4 '' (D) x 38 ]]/]6" (H). 51" (D with door open)

68.6 cm (W) X 75.6 cm (D) X 98.3 cm (H), 129.5 cm (D with door open)

Net Weight 205 lbs (93 kg)

Max. Spin Speed 1,300 RPM

CHOOSE THE PROPER LOCATION

WARNING

*This washer is heavy. Two or more people are

required when moving and unpacking the washer.

Failure to do so may result in damage to property or

serious bodily harm.

*Store and install the washer where it w_ll not be

exposed to temperatures beJow freezing or exposed

to outdoor weather conditions. Failure to follow this warning can cause serious injury, fire, electric shock,

or death.

*Properly ground washer to conform with all electrlc

governing codes and ordinances. Failure to follow this

warning can cause serious injury, fire, electric shock, or death.

*To reduce the risk of electrlc shock, do not install the

washer in humid spaces. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

"To ensure proper air flow, do not block the large

opening on the bottom of the washer with carpeting or other materials.

*Do nat remove ground prong. Do not use an adapter

or extension cord. PJug into a grounded 3-prong outlet. Failure to follow this warning can cause serious

injury, fire, electric shock, or death.

NOTE: installing the washer in a humid space, or installing or storing the washer where it will be exposed to the weather or freezing temperatures, may result in rust or other damage that is not covered in the product warranty.

Power Outlet

.The power outlet must be within 60 in. (1.5 m) of either

side of the washer.

.The appliance and outlet must be positioned so that

the plug is easily accessible.

.Do not overload the outlet with more than

one appliance.

.The outlet must be grounded in accordance with

current wiring electric codes and regulations.

" Time=delay fuse or circuit breaker is recommended.

NOTE: It is the personal responsibility and obligation of the product owner to have a proper outlet installed by a qualified service technician.

CLEARANCES

22 1/41' (57 cm)

I'_ 293/4" I_ql_(lO cm)

(81.2 cm) _ 4 in.

51" _._

(129.5 cm)

To ensure sumcient clearance for water lines and airflow, allow minimum clearances of at least 1 in. (2.5 cm) at the sides and 4 in. (10 cm) behind the unit. Be sure to allow for wall, door, or floor moldings that may increase the required clearances.

o0o

1 L, 27

(2.5 cm) (68.6 cm) (2.5 cm)

Allow at least 27in. (68.6 cm)in front of

the washer to open the door.

FLOORING

• To minimize noise and vibration, the washer MUST be

installed on a solidly constructed floor. See the NOTE to your right.

• Allowable slope under the entire washer is a maximum

1in. difference from side to side or from front to back.

"installing on carpeting and soft tile surfaces is

not recommended.

• Never install the washer on a platform or weakly

supported structure.

NOTE: The floor must be strong and rigid enough to support the weight of the washer, when fully loaded, without flexing or bouncing. If your floor has too much flex, you may need to reinforce it to make it more rigid. A floor that is adequate for a top-loading washer may not be rigid enough for a front loading washer, due to the difference in the spin speed and direction. If the floor is not solid, your washer may vibrate and you may hear and feel the vibration throughout your house.

UNPACKING AND REMOVING SHiPPiNG BOLTS

When removing the washer from the carton base, be sure to remove the foam drum support in the middle of the carton base. See drawing below.

If you must lay the washer down to remove the base packaging materials, always protect the side of the

washer and lay it carefully on its side. DO NOT lay the washer on its front or back.

To prevent internal damage during transport, the washer is equipped with four shipping bolts and plastic retainers.

IMPORTANT: *These shipping bolts and retainers MUST NOT be

removed until just before moving the washer into its final position.

*These bolts and retainers MUST be removed before

operating the washer.

*Failure to remove shipping bolts and retainers may

cause severe vibration and noise, which can lead to permanent damage to the washer.

NOTE: The power cord is secured to the back of the washer with a shipping bolt to help prevent operation with shipping botts in place.

1. Starting with the bottom two shipping bolts, use the wrench (included) to fully loosen all four shipping

bolts by turning them counterclockwise.

FoamTub

Support

Carton

Base

Shipping Bolts

Hole Cap

\\\

2. Remove the bolt assemblies by wiggling them slightly while pulling.

3.Locate the four hole caps included in the accessory pack and install them in the shipping bolt holes.

NOTE: Save the bolt assemblies for future use. To prevent damage to internal components, DO NOT transport the washer without reinstalling the shipping bolts.

CONNECTING THE WATER LINES f

*iMPORTANT: Use new hoses when installing the

washer. Do NOT reuse old hoses.

•Water supply pressure must be between 14.5 psi and 142 psi (100 - 980 kPa). If the water supply pressure is more

than 142 psi, a pressure reducing valve must be installed.

• Periodically check the hose for cracks, leaks, and wear, and replace the hose if necessary.

•Make sure that the water lines are not stretched, pinched, crushed, or kinked.

•The washer should never be installed or stored in a location subject to freezing temperatures. Damage to the

water lines and internal mechanisms of the washer can result. If the washer was exposed to freezing temperatures

prior to installation, allow it to stand at room temperature for several hours before use and check for leaks prior to operation.

•For optimal wash performance, the hot water temperature should be set at 120°-135°F (48-57°C) and the cold water at 60°F (t5°C).

RubberSeal

3. Always run a gallon or two of water through each inlet hose to flush dirt, scale and other debris out

of the water lines. Doing so will help prevent future

problems with clogged filter screens, and will also

allow you to verify which water line is hot and which

is cold.

Water Hose (to water inlet

on washer)

Inspect the threaded fitting on each hose and make sure there is a rubber seal in place in both ends.

Water Fa_

Water Hose/' (to tap)

Cold Water

Water Inlet

Inlet

WARNING: Do not overtighten the hoses. Overtightening can damage the valves resulting in leaking and property damage.

4. Attach the (red) hot water line to the hot water inlet on the back of the washer. Attach the (blue) cold water line

to the cold water inlet on the back of the washer. Tighten the fittings securely.

NOTE: When installing the hoses onto the water

inlet valves, be careful not to cross-thread the hose fittings. DO NOT overtighten the hoses; this could cause damage to internal components, the valve or the hose gasket. Overtightening could result in property damage

from leaks.

2. Connect the water supply hoses to the HOT and COLD water faucets tightly by hand and then tighten another 2/3turn with pliers.

CONNECTING THE DRAIN HOSE

•The drain hose should always be properly secured. Failure to properly secure the drain hose can result in

flooding and property damage.

• Do not install the end of the drain hose lower than

29 in. (73.7 cm) or higher than 96 in. (243.8 cm)

above the bottom of the washer.

•The drain must be installed in accordance with any

applicable local codes and regulations.

• Make sure that the drain hose is not stretched, pinched,

crushed, or kinked.

NOTE:

A drain hose extension kit is //" DrainHoseExtension h available if the drain hose is not| __r_ |

long enough. Do not extend the| _ | drain hose more than 6 feet, as| _ | this will cause poor draining, | _ J

which will result in poor wash and spin performance.

Option 1: Standpipe

Option 2: Laundry Drum

The elbow bracket should be installed near the end of the drain hose. Hang the end of the drain hose over the

side of the utility sink. Use a tie strap to secure the drain hose in place.

Option 3: Floor Drain

Drain Hose

Install the end of the drain hose into the elbow bracket.

Do not extend the drain hose more than 4 inches past the end of the elbow bracket. Use a tie strap to secure the drain hose in place.

NOTE:

• Total height of the hose end should not exceed 96 in.

(243.8 cm) from the bottom of the washer.

• The drain hose should be inserted no more than 8-12

inches into the standpipe. Inserting more than 8-12 inches can cause mold or microorganisms to spread to

the inside of the washer.

If the water valves and drain are built into the wall, fasten the drain hose

to one of the water hoses with the tie strap (ribbed side on inside).

Drain Hose

Insert the end of the drain hose into the floor drain. If possible, secure the hose to prevent it from moving or

coming out of the drain.

CONNECT TO THE POWER SUPPLY

Washer should be plugged into a 120-VAC, 60-Hz grounded 3-prong outlet.

Plug in the washer.

Tie Strap

LEVELING THE WASHER

The drum of your new washer spins at very high speeds. Tominimize vibration, noise, and unwanted movement, the floor must be a level, solid surface.

NOTE: Adjust the leveling feet only as far as necessary to level the washer. Extending the leveling feet more than necessary can cause the washer to vibrate.

NOTE: Before installing the washer, make

sure that the floor is clean, dry and free of

dust, dirt, water and oil so the washer feet cannot slide easily. Leveling feet that

move or slide on the floor can contribute to excess vibration and noise due to

poor contact with the floor. See INSTALLATION OF NON-SKID PADS

for more information.

NOTE: If a drip pan must be used, make sure to follow the

instructions provided with the drip pan and make sure the

leveling feet are adjusted for firm and even contact with the pan. Use of drip pans and failure to properly level the machine may result in increased vibration and noise during operation.

All four leveling feet must rest solidly on the floor. Rock

the washer from corner to corner to make sure that all

four leveling feet are in firm and even contact with the floor.

Tighten all 4 lock nuts

securely using the

wrench.

3. Once the washer is level from side to side and front to back, use the adjusting wrench to tighten all four lock nuts securely to prevent the legs from getting out of

adjustment during operation. Make sure that all four leveling feet are in firm contact with the floor.

NOTE: To make sure that the washer is properly level, run the washer with a test load: place a medium-sized load

of laundry in the machine. Then, press POWER, select

RINSE & SPIN, and press the START/PAUSE button.

See the following sections for additional information on cycle selection and operation. Verify that the washer does not rock or vibrate excessively during the spin cycle. If the

washer vibrates or shakes, adjust the leveling feet, while the washer is spinning, until the vibrations are reduced.

Leveling Feet Leveling Feet

|. Position the washer in its final location, taking special

care not to pinch, strain, or crush the water and drain lines. Place a level across the top of the washer.

2. Loosen the Iocknuts on all four leveling feet with the wrench until you can adjust the feet (wrench

appearance may vary). Use the wrench to turn the feet clockwise to raise the washer, and counterclockwise

to lower the washer. Using a level, adjust the feet until the washer is level from side to side and front to back.

Make sure that all four feet are in firm contact with the floor.

INSTALLATION OF NON-SKID PADS (optional)

Some floor surfaces are too slippery to prevent the washer from moving on the floor during heavily

unbalanced loads. While it is normal for an occasional load to be out of balance, excess noise and vibration can

result from the washer moving out of position. If these conditions are encountered, follow the instructions below for installation of the non-skid pads. These pads will help prevent the washer from moving during heavy, out of balance conditions, thereby reducing noise and vibration.

NOTE: The non-skid pads are included in the installation packet

Non-skid pads

This side up

, Stick adhesive side to floor

move backing

g<Placethe pads under both front feet.

NOTE: If you are installing the washer on the optional pedestal, the washer leveling feet should be fully retracted. Use the leveling feet on the pedestal to level the washer.

WARNING: Toreducetheriskafnre,electrlcshack,orinjurytopersons,readandfonawthis

entire Use & Care Guide, includlng the Important Safely Instructions, before operating this washer.

CONTROL PANEL FEATURES

Normal I Casual e

Heavy Duty e

Whitest Whites o

Bulky

Comforter

POWER

Kids Wear •

POWER (ON/OFF) BUTTON Press to turn the washer ON or OFF.

NOTE: Pressing the POWER button during a

cycle will cancel that cycle and any load settings will be lost. The door will unlock after a

brief pause, unless the water level or

temperature is too high.

CYCLE SELECTOR KNOB

Turnthis knob to select the desired cycle. Once the desired cycle has been selected, the standard presets

will appear in the display. These settings can be adjusted using the cycle setting buttons anytime

before starting the cycle.

• Workout Wear

• Delicates

• Small Load

• Express Wash

• Cold Clean

• Rinse & Spin

=_Acce!_sh Auto Soak Pre Welsh Extra Rinse Delay Start Stay Fresh

Hot • Extra High • Heavy

e Warm e High • ® Cool • Medium • Normal

STARTIPAUSE

• Cold • Low •

• Top Cold • No Spin • Light

CYCLE MODIFIER BUTTONS

Use these buttons to adjust the settings for the selected cycte. The settings light up above the

buttons to show the current selection.

O SPECIAL CYCLE AND OPTION BUTTONS

These buttons are used to activate special cycles or options.

O TIME AND STATUS DISPLAY

The display shows the cycle status, door lock status and estimated time remaining.

Mycy-%,oi

_%Connect

• Loud e Soft

• Off

e START/PAUSE BUTTON

Press this button to start the selected cycle. if the washer is running, use this button to pause

the cycle without losing the current settings.

NOTE: If you do not press the START/PAUSE button within four minutes of selecting a cycle,

the washer automatically turns OFF.

NOTE: To protect your clothing, not all settings are available on all cycle selections.

OPERATING THE WASHER

POWER

SORT LAUNDRY AND LOAD WASHER

Sort laundry by fabric type, soil level, color and toad size, as needed. Open the door and load selected items into the

washer.

TURN ON THE WASHER

Press the POWER button to turn ON the washer. The lights around the cycle selector knob will illuminate and a chime will sound.

Normal ICasuaN • • Workout Wear

Heavy Duty e _ • Demlcates

BuNky e • Express Wash

Comforter ® • CoredCNean

Whitest Whites e _ • Small Load

Kids Wear • • Rinse & Spin

• Hot • Extra High e Heavy ,_'_Connect

• Warm • High •

• Coom • Medium • Normal • Loud

• Cold e Low • • e Soft

• TapComd • No Spin • Light • Off

W_WasashTemp I I Spin Speed I _o"Le_e_ I Chlme

ALLco_o_INS_S

! ....... 1_cceJa-Wash Auto Soak Pre Wash Extra Rinse Delay Start Stay Fresh My Cycle

SELECT A CYCLE

Turn the cycle selector knob in either direction to select the desired cycle. The preset Wash Temperature, Spin Speed, Soil

Level, and Option settings for that cycle will be shown.

SELECT CYCLE MODiFiERS

Default settings for the selected cycle can now be changed if desired. Use the cycle modifier buttons.

NOTE: To protect your fabrics, not all modifiers are available on all cycles.

SELECT CYCLE OPTIONS

Cycle options can be added using the option buttons.

NOTE: To protect your fabrics, not all modifi ers are available on all cycles. Cycle options can also be added by using the

option buttons.

NOTE: Not att options are available on all cyctes. A different chime will sound and the LED will not come on if the selection

is not allowed.

START/PAUSE

ADD DETERGENT

Add High-Efficiency (HE) detergent to the detergent dispenser drawer. For proper wash performance, always measure the detergent using the measuring device provided by the detergent manufacturer.

BEGIN CYCLE

Press the START/PAUSE button to begin the cycte. The door will lock, and the washer will briefly tumble the load without water to measure its weight. Once the weight of the load is

measured, the washer will begin the selected wash cycte.

Pressing the START/PAUSE button will pause the cycte and the door witl unlock. Press the START/PAUSE button again to

resume the wash cycle.

CYCLE GUIDE

The cycle guide below shows the default settings, available options and recommended fabric types for each cycle. Allowable modifier adjustments are shown below the default setting for each cycle. : Default Setting

Cottonn

Normal/

Casual

linen, towels, Hot

shirts, sheets, Warm Extra High jeans, mixed Cold Medium

loads. Tap Cold Low

: Available Option

Heavy

Duty

Whitest

Whites

Bulky

Comforter

Kids

Wear

Heavily

soiled cotton Warm High fabrics. Cool Medium

Heavily to normally Cool Medium

soiled white Cold Low cottons. Tap Cold

Large items

suchas Warm

blankets and Cold

comforters. Tap Cold

Comfo rters, blankets, Warm Medium

rugs. Cold Low

Specially

designed to clean and Cool

thoroughly Cold

rinse kids Tap Cold No Spin

wea r.

Tap Cold Low

Extra High

No Spin

Low

No Spin

Tap Cold No Spin

Extra High

Medium

Low

NOTE:

• To protect your garments, not every wash temperature, spin speed, soil level, or option is available with every cycle. A chime will sound and the LED will not light if the selection is not allowed.

• The washer automatically adjusts the wash time for the amount of laundry, water pressure, water heating time and other operating conditions.

•These cycles use various wash motions to enhance cleaning and/or fabric care performance. The wash motions may sound different at different stages of the wash cycle. This is normal

"When the Accela-wash option is selected, the drum spins to rinse the clothes. To use the No Spin option, you must

deselect the Accela-wash option.

CYCLE GUIDE (continued) _ = Available Option

Permanent

Workout

Wear

Delicates

press, synthetic Cold Low

items. Tap Cold No Spin

Dress shirts, blouses, nylons, sheer Cool Low

or lacy Tap Cold No Spin garments.

Small soiled and Warm

Load small loads. Cold Medium _ @ _

Express clothing and Cool @ _ @

Wash Medium

Cold linen, towels, 7 2 Medium @ @

Clean shirts, sheets, Tap Cold

Rinse & only need to Medium @ _

Spin be rinsed. Low

Normally Extra High

Tap Cold

Lightly soiled High small loads. Cold

Tap Cold

Small loads

of cotton,

jeans, mixed Low

loads. No Spin

Loads that Extra High

Low

No Spin

Low

No Spin

Extra High

No Spin

@ @

NOTE: *To protect your garments, not every wash temperature, spin speed, soil level, or option isavailable with every

cycle. A chime will sound and the LED will not light if the selection is not allowed.

*The washer automatically adjusts the wash time for the amount of laundry, water pressure, water heating time and

other operating conditions.

*These cycles use various wash motions to enhance cleaning and/or fabric care performance. The wash motions may

sound difTerent at different stages of the wash cycle. This is normal.

*When the Accela-wash option is selected, the drum spins to rinse the clothes. To use the No Spin option, you must

deselect the Accela-wash option.

SORTING WASH LOADS

Fabric Care Labels

Many articles of clothing include a fabric care label. Using the chart below, adjust the cycle and option

selections to care for your clothing according to the manufacturer's recommendations.

Fabric Care Labels

Machine wash

cycle

Normal Permanent press/ Gentle/

wrinkle resistant delicate

H h Do not wash Do not wring

Water 0 • Q 00 • temperature Hot Warm Cold/cool

Bleach

s m o,s

Any bleach Onlynon-chlorine bleach Do not bleach

(when needed) (when needed)

Grouping Similar items

For the best washing results, and to reduce the possibility of damage to clothing, care should be taken to sort the clothing into loads that are made up of similar items. Mixing different fabric types and/or soil levels can result in poor wash performance, color transfer or discoloration, fabric damage or linting. Fabrics should be sorted into groups as described below.

Loading the Washer

• Check all pockets to make sure that they are empty.

Items such as clips, matches, pens, coins, and keys can damage both your washer and your clothes.

•Close zippers, hooks, and drawstrings to prevent these items from snagging or tangling on other clothes.

*Pretreat heavily stained areas for best results.

•Combine large and small items in a load. Load large

items first.

• Large items should not be more than half of the total wash load.

•The drum should not be tightly packed with items. The door of the washer should close easily.

•To prevent an out-of-balance load, do not wash single items. Add one or two similar items to the load. Large, bulky items, such as a blanket, comforter, or bedspread, should be washed individually.

•Do not wash or spin waterproof items, such as rain coats, sleeping bags, etc.

•When unloading the washer, check under the door seal for small items.

NOTE: Make sure that the door seal area is clear when closing the door. Overloading the washer can cause items

to get caught between the door and the seal. This can damage both the items and the seal.

Colors

Sort articles by color. Wash dark clothes together in a separate load from light colors or whites. Mixing dark clothes with light clothes can result in dye transfer or discoloration of the lighter clothes.

Soll Level

Wash heavily soiled clothing together. Washing lightly soiled clothing in the same load with heavily soiled clothing could result in poor wash performance for the lightly soiled clothing.

Fabric Type

Delicate articles should not be mixed with heavier or sturdier fabric types. Washing delicates in a load with

heavy fabrics can result in damage to the more delicate fabrics. Washing heavier fabrics in a delicate load can

result in poor wash performance for the heavier fabrics and possible damage to the delicates.

Lint Type Some fabrics attract and bind lint to them while others give off lint in the laundry process. Avoid mixing these

lint collectors and lint producers in the same load. Mixing these fabrics will result in pilling and linting on the lint collectors. (For example, lint collector - knit sweater; lint producer - terrycloth towels.)

* DO NOT OVERLOAD THE DRUM

* MAKE SURE CLOTHING iS NOT

CAUGHT iN THE DOOR GASKET

by Cobrs Whites Lights

Sort Laundry...

Darks

by Soil

Heavy

Norrnal Light

by Fabric Delicates Easy Care

Sturdy

by Lint Lint Producer

Lint Collector

ABOUT THE DISPENSER DRAWER

The automatic dispenser consistsof four compartments which hold:

•Liquid chlorine bleach.

•Liquid fabric softener.

•Liquid or powdered detergent for prewash.

• Liquid or powdered detergent and color-safe bleach for main wash.

Liquid Chlorine Bleach

Compartment

Main Wash Detergent

Compartment

Liquid Fabric

Softener Compartment

Liquid

•Detergent Cup

Prewash Detergent Compartment

Pre-Wash Detergent Compartment

Add liquid or powdered detergent to this compartment when using the Pre-Wash option. Always use High- Efficiency (HE) detergent with your washing machine.

The amount of detergent added for the Pre-Wash option should be 1/2the amount recommended for the main wash cycle. For example, if the main wash cycle requires 1/2measure of detergent, add 1/4measure to the Pre-Wash compartment.

NOTE: If using liquid detergent for the main wash, when using the Pre-Wash option, the liquid detergent cup accessory must be used in the main wash dispenser. This will prevent the main wash liquid detergent from being dispensed immediately.

Main Wash Detergent Compartment

This compartment holds laundry detergent for the main wash cycle. The detergent is added to the load at the beginning of the cycle. Always use High-Efficiency (HE) detergent with your washing machine. Either powdered or liquid detergent may be used.

Never exceed the manufacturer's recommendations when adding detergent. Using too much detergent can

result in detergent buildup in clothing and the washer. NOTE: Liquid or powdered color-safe bleach may be

added to the main wash compartment with detergent of the same type. DO NOT add liquid or powdered color-safe bleach to the bleach dispenser. DO NOT mix liquid and powdered cleaning agents within the same

compartment.

Liquid Bleach Compartment

This compartment holds liquid chlorine bleach, which is dispensed automatically at the proper time during the

wash cycle.

•Do not add powdered or liquid color-safe bleach to this compartment. The bleach compartment is designed to dispense liquid chlorine bleach only. Powdered or

liquid color-safe bleach will not dispense properly.

*Always follow the manufacturer's recommendations

when adding bleach. Do not exceed the maximum fill

line since this can cause the bleach to be dispensed immediately, causing damage to fabrics. Using too much bleach can damage fabrics.

*Never pour undiluted liquid chlorine bleach directly

onto the load or into the drum. Fabric damage can occur.

Fabric Softener Compartment This compartment holds liquid fabric softener, which is

automatically dispensed during the final rinse cycle.

Never exceed the manufacturer's recommendations when adding softener. Using too much fabric softener can result

in buildup in clothing and the washer. Either powdered or liquid fabric softener may be used.

•Always follow the manufacturer's recommendations when adding fabric softener. Do not exceed the

maximum fill line. Using too much fabric softener may stain clothes.

•Dilute concentrated fabric softeners with warm water.

Do not exceed the maximum fill line.

•Never pour fabric softener directly onto the load or

into the drum.

DETERGENT AND DISPENSER USE

A Word About Detergents

High-Efficiency (HE) detergents produce fewer suds,

dissolve more efficiently to improve washing and rinsing

performance, and help to keep the interior of your washer clean. Using detergent that is not HE may cause oversudsing and unsatisfactory performance which could result in error codes, cycle failure, and

machine damage.

Filling the Dispenser

To add detergent and fabric softener to the automatic dispenser:

Open the dispenser drawer.

O Load the laundry products into the

appropriate compartments.

O Close the drawer before starting the cycle.

--_ Maximum _ [--] ormal Load AmountJ_2Z:--- _

Liquid Powdered

Detergent Detergent

For proper wash performance, always measure the detergent using the measurements provided by the detergent manufacturer.

The normal amount of HE detergent needed, for average

loads, is less than 1/2of the recommended maximum. Use less detergent for soft water, light soil or smaller

loads. Never use more than the maximum amount recommended by the detergent manufacturer.

Designed to use only High-Efflciency (HE) detergent

IMPORTANT: Your washing machine isdesigned for use

with only High-Efficiency (HE) detergents. HE detergents are formulated specifically for front-load washers and contain suds-reducing agents. Always look for the HE symbol when purchasing detergent.

NOTE: It is normal for a small amount of water to remain in the dispenser and softener compartment at the

end of the cycle. IMPORTANT: Do not place or store laundry products,

such as detergent, Bleach dispenser, or liquid fabric softener, on top of your washer or dryer.

Wipe up any spills immediately. These products can damage the finish and controls.

iMPORTANT: Not all detergents are the same. Pay careful attention to the amount of detergent used to avoid oversudsing, poor rinsing and detergent buildup in clothing, and residue buildup that can contribute to odors in the machine. NEVER use a cup or scoop other than the

one supplied by the manufacturer of the detergent you are using. Never use more than the maximum amount of detergent recommended by the manufacturer.

Always measure the detergent amount. While HE detergents are designed for this type of washing

machine, be careful when measuring the detergent. For

most normal loads, no more than 1/4to 1/2 of cap or

scoop of HE detergent should be used.

NOTE: Extra care must be exercised when using 2X and

3X concentrated detergents because even a little bit extra

can contribute to the problems mentioned above.

NOTE: Detergents designated as HE compatible may not

provide optimal results.

+ 42 hidden pages