Kenmore Elite 72180863400, 72180864400, 72180869400 Installation Guide

Models/Modelos

721.80862

721.80863

721.80864

721.80869

INSTALLATIONINSTRUCTIONS

INSTRUCCIONESDEINSTALACION

! ,

I

E 1 T E {.}

ULTRAWAVE_"MicrowaveHood

Read and save these
installation instructions.

Lea y guarde estas
instrucciones de

instalaci6n

Part No.3828W5U0390 Sears, Roebuck andCo., Hoffman Estates, IL.60179 U.S.A www.sears.com.

Combination

Combinaci6nMicroondasCampana
deULTRAWAVETM

YOUR SAFETY FIRST

BEFORE YOU START

• Proper installation is the installer's responsibility!

- Read the entire manual before you begin.

- The model number label is located on the oven front. See Figure 1.

- Mounting plate is located on back side of microwave oven. See Figure 2.

BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS:

Mounting

U

plate
(Remove fror
oven to install.)

Back of oven

Figure 1 Figure 2

A WARNING A

FOR YOUR SAFETY:

• You will need TWO people to install this oven. It is heavy and could cause personal injury if not handled
properly. The dimensions of the oven are as follows:

Height : 16-7/16 inches
Width : 29-15/16 inches

Depth : 16-1/8 inches
Weight : 53 pounds

• AVOID ELECTRICAL SHOCK!

- Before you drill into the wall, note where electrical outlets are and where electrical wires might be

concealed behind the wall.
YOU COULD GET AN ELECTRIC SHOCK it you contact electrical wires with your drill bit.

- Locate and disconnect the power of any electrical circuits that could be affected by installing this oven.

IF YOU DO NOT DISCONNECT THE POWER, YOU COULD GET AN ELECTRIC SHOCK.

• ELECTRICAL RATING OF THIS OVEN : 120V, 60Hz.

- You need a 120V, 60Hz, AC only, 20A, fused electrical supply (located in the cabinet above the

microwave as close as possible to the microwave circuit) serving only the microwave.

2

YOUR SAFETY FIRST

• THIS APPLIANCE MUST BE GROUNDED!

- If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape

wire for the electric current. This appliance is equipped with a cord having a grounding wire with a
grounding plug.

• Place the plug into a properly installed and grounded
outlet. See Figure 3.

• Do not use an extension cord.

• Keep the power cord dry and do not pinch or crush it.

• DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE
THE POWER SUPPLY CORD GROUNDING PRONG!

This appliance MUST be grounded!

A WARNING A

If you use the grounding plug improperly, you risk electric shock!

- Check with a qualified electrician if you are not sure whether the oven is properly grounded or if you do

not completely understand the grounding instructions.
DO NOT USE A FUSE IN THE NEUTRAL OR GROUNDING CIRCUIT.

PROPERLY POLARIZED AND

GROUNDED OUTLET

Three-Pronged (Grounding) plug

Figure 3

I'll

Z

63

i=

m

01

A WARNING A

Improper grounding could result in electric shock or other personal injury.

SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.

• DO NOT EXPOSE YOURSELF TO EXCESSIVE MICROWAVE ENERGY!

- DO NOT try to operate the microwave oven with the door open.

- DO NOT tamper with or defeat the safety interlocks.

- DO NOT place objects between the microwave oven front face and the door.

- DO NOT allow soil or cleaner residue to build up on the flat surfaces around the microwave oven door.

- DO NOT operate the microwave oven if it is damaged.

- The microwave oven door must close properly to operate safely.

- DO NOT use the microwave oven:

• If the door is bent.

• If the hinges or latches are broken or loose.

• If the door seals, sealing surfaces or glass is broken.

- DO NOT attempt to adjust or repair the oven yourself!

It should be adjusted and repaired by a qualified technician who can check for microwave leakage after
repairing the oven.

A WARNING A

If you do not use the microwave oven as instructed, you could be exposed

to excessive microwave energy.

3

YOUR SAFETY FIRST

• MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT.

- Mount the oven against a flat, vertical wall, so that it is supported by the wall. The wall should be

constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.

- ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, 2" x 4" wall stud.

- DO NOT mount the microwave oven to an island or peninsula cabinet.

- BE SURE the upper cabinet and rear wall structures are able to support 150 Ibs., plus the weight of any

items you place inside the oven or upper cabinet.

- Locate the oven away from strong draft areas, such as windows, doors, and strong heating vents.

- BE SURE you have enough space. See Figure 4 below for minimum vertical and horizontal clearance.

A WARNING A

If you do not mount the oven as instructed, you risk personal injury and/or
property damage.

30" rain. cabinetopening width

30" rain.clearancefrom bottom
of cabinet to cookingsurface
or countertop

(Use templates included

with installation instructions)

Figure 4

_Grounded Plug

(inside upper cabinet)

Power Supply
Cord Hole

CAUTION A

• Before you begin installing the oven, PLACE A PIECE OF THE CARTON OR OTHER HEAVY MATERIAL

(a blanket) over the countertop or cooktop to protect it. Do not use a plastic cover.
Failure to protect these surfaces could result inproperty damage.

4

PARTS, TOOLS, MATERIALS

THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN:

NOTE: Depending on your ventilation requirements, you may not use all of these parts.

Damper/duct connector

(for roof vented or wall vented installation)
Not Actual Size

One power cord clamp bushing - Actual Size (for the cord hole in a metal upper cabinet)

Four 1/4" x 2" lag screws - Actual Size

(for wall stud holes)

Two 1/4" x 3" bolts - Actual Size

One power cord clamp and
One dark-colored mounting screw

(to hold the power cord)

Actual Size

Four 1/4" x 3" toggle bolts - Actual Size
(for drywall holes)

Two tapping screws - Actual Size

(for attaching the damper duct connector)

I11

Z

61

I=

m

01

OR

Four spring toggle heads - Actual Size
(for the toggle bolts)

NOTE: You need to install at least one lag screw into a 2" x 4" stud and four anchor bolts into the wall,

and the mounting area must meet the 150 Ibs. weight requirement.

One upper cabinet template - Not Actual
Size

5

PARTS, TOOLS, MATERIALS

YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE

INSTALLATION:

Carton or other heavy material for covering the counter top.

r-

Ul

Clear tape
(for taping the templates to the wall)

Saber saw (for cutting vent holes for roof
or wall venting)

Phillips screwdriver (for the screws)

Pencil

Flat blade screwdriver (for the bolts)

Stud finder or thin nail.

Key hole saw (for the power cord hole)

3/8" and 3/4" wood drill bits

1/2" and 3/16"

drill bits

I

Plumb line

Measuring tape (metal preferred)

Small side cutters or tin snips

Gloves

• If you have brick or masonry walls, you need special hardware and tools.

• The ductwork you need for the installation is not included. All wall and roof caps must have a back-draft
damper.

6

DuctTape

Caulking gun