Kenmore Elite 59672282201, 59672282202, 59672283201, 59672283202, 59672284201 Owner’s Manual

...

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Sears Canada, Inc., Toronto, Ontario, Canada M5B 2B8

ENGLISH FRANÇAIS ESPAÑOL

Part No. 12642729 Form A/04/03

www.sears.com

Au Canada, www.sears.ca

Bottom Freezer Refrigerator

Use & Care Guide

Refrigerador con montaje inferior

Manual de uso y cuidado

Réfrigérateur à compartiment inférieur

Guide d’utilisation et d’entretien

Models:

596.72282200, 596.72283200, 596.72284200, 596.72289200,

596.72282201, 596.72283201, 596.72284201, 596.72289201,

596.72282202, 596.72283202, 596.72284202, 596.72289202

Important safety information

What you need to know about safety instructions

Warning and Important Safety Instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution, and care must be exercised when installing, maintaining, or operating refrigerator.

Always contact your dealer, distributor, service agent, or manufacturer about problems or conditions you do not understand.

Save these instructions

DANGER – Immediate hazards which WILL result in severe personal

injury or death.

DANGER

WARNING – Hazards or unsafe

practices which COULD result in

severe personal injury or death.

WARNING

CAUTION – Hazards or unsafe

practices which COULD result in

minor personal injury.

CAUTION

To reduce risk of fire, electric shock, serious injury or death when using your refrigerator, follow these basic precautions, including the following:

WARNING

To reduce risk of injury or death, follow basic precautions, including the following:

IMPORTANT: Child entrapment and

suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous – even if they sit out for “just a few days.” If you are getting rid of your old refrigerator, please follow the instructions below to help prevent accidents.

Before you throw away your old refrigerator or freezer:

➢ Ta ke off the doors. ➢ Leave the shelves in

place so children may not easily climb inside.

DANGER

RECOGNIZE SAFETY SYMBOLS, WORDS, LABELS

1. Read all instructions before using the refrigerator.

2. Observe all local codes and ordinances.

3. Be sure to follow grounding instructions.

4. Check with a qualified electrician if you are not sure this appliance is properly grounded.

5. DO NOT ground to a gas line.

6. DO NOT ground to a cold-water pipe.

7. Refrigerator is designed to operate on a separate 103 to

126 volt, 15 amp., 60 cycle line. DO NOT modify plug on

power cord. If plug does not fit electrical outlet, have proper outlet installed by a qualified electrician.

8. DO NOT use a two-prong adapter, extension cord or

power strip.

9. DO NOT remove warning tag from power cord.

10. DO NOT tamper with refrigerator controls.

11. DO NOT service or replace any part of refrigerator unless

specifically recommended in Use & Care or published

user-repair instructions. DO NOT attempt service if

instructions are not understood or if they are beyond personal skill level.

12. Always disconnect refrigerator from electrical supply before attempting any service. Disconnect power cord by grasping the plug, not the cord.

13. Install refrigerator according to Installation Instructions. All connections for water, electrical power and grounding must comply with local codes and be made by licensed personnel when required.

14. Keep your refrigerator in good condition. Bumping or dropping refrigerator can damage unit or cause unit to malfunction or leak. If damage occurs, have refrigerator checked by qualified service technician.

15. Replace worn power cords and/or loose plugs.

16. Always read and follow manufacturer’s storage and ideal environment instructions for items being stored in refrigerator.

ENGLISH FRANÇAIS ESPAÑOL

Protection agreements

Master protection agreements

IN THE U.S.A.

Congratulations on making a smart purchase. Your new Kenmore

appliance is designed and manufactured for years of dependable operation. But like all products, it may require preventive maintenance or repair from time to time. That is when having a Master Protection Agreement can save you money and aggravation.

Purchase a Master Protection Agreement now and protect yourself from unexpected hassle and expense.

The Master Protection Agreement also helps extend the life of your new appliance. Here is what is included in the agreement:

➢ Expert service by our 12,000

professional repair specialists.

➢ Unlimited service and no charge for

parts and labor on all covered repairs.

➢ “No-lemon” guarantee – replacement

of your covered product if more than three product failures occur within twelve months.

➢ Product replacement if your covered

product cannot be fixed.

➢ Annual Preventive Maintenance

Check at your request – no extra charge.

➢ Fast help by phone – non-technical

and instructional assistance on products repaired in your home, plus convenient repair scheduling.

➢ Power surge protection against

electrical damage due to power fluctuations.

➢ Rental reimbursement if repair of

your covered product takes longer than promised.

Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night, or schedule a service appointment online.

Sears has over 12,000 professional repair specialists, who have access to over 4.5 million quality parts and accessories. That is the kind of professionalism you can count on to help prolong the life of your new purchase for years to come. Purchase your Master Protection Agreement today!

Some limitations and exclusions apply. For prices and additional information, call 1-800-827-6655.

Sears Installation Service

For Sears guaranteed professional installation of home appliances and items like garage door openers and water heaters, in the U.S.A. call 1-800-MY-HOME

Maintenance agreements

IN CANADA

Your purchase has added value because you can depend on Sears HomeCentral

for service. With over 2,400 service technicians and access to over 900,000 parts and accessories, we have the tools, parts, knowledge and skills to ensure our pledge: We Service What We Sell.

Your Kenmore®appliance is designed, manufactured and tested to provide years of dependable operation. Yet any major appliance may require service from time to time. The Sears Maintenance Agreement offers you an outstanding service program, affordably priced.

Sears Maintenance Agreement

➢ Is your way to buy tomorrow’s service

at today’s price.

➢ Eliminates repair bills resulting from

normal wear and tear.

➢ Provides for non-technical and

instructional assistance.

➢ Even if you don’t need repairs,

provides an annual Preventive Maintenance Check, at your request, to ensure that your appliance is in proper running condition.

Some limitations apply. For information concerning Sears Canada Maintenance Agreements, call 1-800-361-6665.

Warranty

Full One Year Warranty on Refrigerator

For one year from the date of purchase, when this refrigerator is operated and maintained according to instructions attached to or furnished with it, Sears will repair it, free of charge, if defective in material or workmanship.

Full Five Year Warranty on Sealed Refrigeration System

For five years from the date of purchase, when this refrigerator is operated and maintained according to instructions attached to or furnished with it, Sears will repair the sealed system (consisting of refrigerant, connecting tubing and compressor motor) free of charge, if defective in material or workmanship.

The above warranty coverage applies only to refrigerators which are used for storage of food for private household purposes. It excludes original and replacement Kenmore ice & water filter cartridges. Original and replacement cartridges are warranted for 30 days, parts only, against defects in material or workmanship.

Warranty service is available by contacting 1-800-4-MY-HOME

(1-800-469-4663).

This warranty applies only while this product is in use in the United States and Canada.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

NOTE: Some Reverse Osmosis home

water systems cause low water pressure. Low water pressure can affect the water and ice dispensing system by causing small or hollow ice cubes and slow water flow from the dispenser. Service problems related to the home’s Reverse Osmosis water system are not covered by the warranty.

Product record

In the space below record the model and serial numbers and purchase date of your refrigerator. You will find the model and serial number sticker inside the refrigerator section on the left wall.

Model Number: 596. _______________

Serial Number: ____________________

Purchase Date: ____________________

Keep this booklet and your Sears sales receipt in a safe place for future reference.

ENGLISH FRANÇAIS ESPAÑOL

Contents

Important Safety Information ......................................................................................2

What You Need to Know About Safety Instructions...................................................2

Protection Agreements ................................................................................................3

Master Protection Agreements – U.S.A.....................................................................3

Maintenance Agreements – Canada .........................................................................3

Warranty ........................................................................................................................4

Product Record .............................................................................................................4

Installing Your Refrigerator ....................................................................................6-11

Measuring the Opening .............................................................................................6

Transporting Your Refrigerator...................................................................................6

Selecting the Best Location .......................................................................................6

Removing and Replacing Handles ............................................................................6

How to Remove the Hinges, Door and Drawer .........................................................7

How to Reverse the Door ..........................................................................................8

How to Replace the Hinges, Door and Drawer .........................................................8

How to Connect the Water Supply.............................................................................9

How to Level Your Refrigerator................................................................................10

Setting and Maintaining Proper Temperatures........................................................11

Initial Control Settings ..............................................................................................11

Adjusting the Controls ..............................................................................................11

Fresh Food Storage .................................................................................................11

Frozen Food Storage ...............................................................................................11

About Your Water Filter ........................................................................................12-13

Water Filter Installation and Removal......................................................................12

Water Filter Data......................................................................................................13

Fresh Food Features.............................................................................................14-15

Water Dispenser ......................................................................................................14

Interior Shelves ........................................................................................................14

Door Storage............................................................................................................14

Climate-Controlled Drawers.....................................................................................15

Freezer Features.........................................................................................................16

Automatic Ice Maker ................................................................................................16

Drawers....................................................................................................................16

Hints and Care.......................................................................................................17-18

How to Clean Your Refrigerator ...............................................................................17

How to Remove Odors from Refrigerator ................................................................18

Energy Saving Ideas................................................................................................18

How to Remove and Replace Light Bulbs...............................................................18

Normal Operating Sounds.........................................................................................19

Troubleshooting ....................................................................................................20-21

Operation ............................................................................................................20-21

Ice and Water...........................................................................................................21

Français.......................................................................................................................23

Español........................................................................................................................44

Service ..........................................................................................................Back Cover

Installing your refrigerator

These instructions were provided to aid you in the installation of your refrigerator.

Measuring the opening

A one-half inch (

⁄2") of air space must be

provided for the top and the back of the refrigerator. When installing your refrigerator, measure carefully.

Subflooring or floor coverings (i.e. carpet, tile, wood floors, rugs) may make your opening smaller than anticipated.

Some clearance may be gained by using the leveling procedure under

How to Level Your Refrigerator

(page 10).

IMPORTANT: If refrigerator is to be

installed into a recess where top of refrigerator is completely covered, use dimensions from floor to top of hinge cap to verify proper clearance.

Transporting your refrigerator

Follow these tips when moving the refrigerator to final location:

➢ NEVER transport refrigerator on its

side. If an upright position is not possible, lay refrigerator on its back. Allow refrigerator to sit upright for approximately 30 minutes prior to plugging refrigerator in to assure oil returns to the compressor. Plugging refrigerator in immediately may cause damage to internal parts.

➢ Use an appliance dolly when moving

refrigerator. ALWAYS truck

refrigerator from its side or

back–NEVER from its front.

➢ Protect outside finish of refrigerator

during transport by wrapping cabinet in blankets or inserting padding between the refrigerator and dolly.

➢ Secure refrigerator to dolly firmly with

straps or bungee cords. Thread straps through handles when

possible. DO NOT overtighten. Over-

tightening restraints may dent or damage outside finish.

Selecting the best location

Observe these points when choosing the final location for your refrigerator:

➢ DO NOT install refrigerator near

oven, radiator or other heat source. If not possible, shield refrigerator with cabinet material.

➢ DO NOT install where temperature

falls below 55° F (13° C). Malfunction may occur at this temperature.

➢ To assure proper door closure, follow

the leveling instructions in the

section, How to Level Your Refrigerator (page 10).

Removing and replacing handles

1. Remove top and bottom door trim by removing 4 screws*. Lift handle corner of trim and slide toward hinge edge of door.

➢ Retain all screws for later use.

2. Remove handle by removing 2 screws* from top and bottom edge of handle.

➢ Retain all screws for later use.

Removing Freezer Handle

1. Remove handle by removing 3 screws* from handle.

➢ Retain all screws for later use.

Replacing Fresh Food Handle

1. Install handle by fastening with screws* from previous removal.

2. Install top and bottom door trim.

➢ Locate hinge hole corner of trim.

Install hinge hole corner of trim, then install handle edge of trim.

Replacing Freezer Handle

1. Install handle by fastening with screws* from previous removal.

* Fasteners may require either a T-15 Torx®driver or a Phillips screwdriver.

Torx®is a registered trademark of Textron Inc.

To avoid possible injury and damage to property:

➢ DO NOT remove secondary cap

when removing door trim.

➢ Place doors on nonabrasive

surface protected by towels or rugs while working directly on door.

CAUTION

Removing Fresh Food Handle NOTE: These instructions are best

followed with the fresh food door

removed. See How to Remove the Hinges, Door and Drawer for

instructions.

ENGLISH ESPAÑOL FRANÇAIS

To avoid electrical shock, which can cause severe personal injury or death, observe the following:

➢ Disconnect power to refrigerator

before removing doors. Connect power only after replacing doors.

WARNING

To avoid damage to walls and flooring, protect soft vinyl or other flooring with cardboard, rugs, or other protective material.

CAUTION

How to remove the hinges, door and drawer

Some installations require door removal to get refrigerator into final location.

1. Unplug power cord from power source.

2. Remove top hinge covers by removing Phillips screws.

➢ Retain screw and

cover for replacement.

3. Unscrew

⁄16" hex head screws from

top hinge to remove hinge.

➢ Retain all screws for later use.

4. Lift refrigerator door from center hinge pin.

5. Remove center hinge pin with a

⁄16" hex head

driver.

➢ Retain hinge pin for

later use.

6. Remove Phillips screws to remove center hinge.

➢ Retain all screws

for later use.

To avoid possible injury, product, or property damage, you will need two people to perform the following instructions.

CAUTION

10. Lift top of door to unhook door supports from rail system. Lift door out to remove.

11. Remove toe grille and bottom bracket covers.

7. Pull drawer open to full extension.

8. Remove lower basket by pressing inward on basket sides, then lift basket.

9. Pull upper basket out to full extension, and lift out to remove.

12. Remove both stabilizing brackets with

⁄8" hex head driver.

➢ Retain screws for later use.

Press Tab Here

How to replace the hinges, door and drawer

1. Install stabilizing brackets with

⁄8" hex

head driver.

2. Replace toe grille and bottom bracket covers.

➢ Snap bottom portion into place

first. Press down on top part of

grille until top portion snaps into place.

3. Pull both rails out to full extension.

Installing your refrigerator,

cont.

7. Install center hinge with Phillips screws.

8. Install center hinge pin with

⁄16" hex

head driver.

➢ Replace any applicable door

shims.

➢ Make sure the hinge pin is

installed tightly.

9. Install top hinge loosely with

⁄16" hex

head screws.

10. Place hinge side of refrigerator door on center hinge pin.

11. While holding refrigerator door upright, tighten door top hinge with

⁄16" hex head driver.

12. Replace top hinge cover on hinge.

4. Hook door supports into rail tabs, as illustrated, and lower door into final position.

5. With drawer pulled out to full extension, insert lower basket by aligning tabs on both side of lower basket with notches in rail assembly.

6. Slide upper basket into refrigerator. Make sure that rear of basket hooks behind rail catch.

To avoid possible injury and damage to property:

➢ DO NOT remove sub cap when

removing door trim.

➢ Place doors on nonabrasive

surface protected by towels or rugs while working directly on door.

CAUTION

* Fasteners may require either a T-15 Torx®driver or a Phillips screwdriver.

Torx®is a registered trademark of Textron Inc.

How to reverse the door

1. Perform all steps listed in How to Replace the Hinges, Door and Drawer (page 8).

2. Transfer cabinet plugs and screws to opposite side of cabinet.

➢ Remove plugs with flat blade of

screwdriver wrapped in masking tape.

➢ Remove center mullion screws

with

⁄16" hex head driver.

3. Remove door stop from fresh food door with Phillips screwdriver.

4. Remove bottom door trim by removing 4 Phillips screws. Lift handle corner of trim and slide toward hinge edge of door.

5. Remove top door trim by removing 4 screws*. Lift handle corner of trim and slide toward hinge edge of door.

➢ Retain all screws for later use.

6. Reverse handle by removing two screws* from top and bottom edge of handle and reattaching handle on opposite side of door.

7. Install top door trim on bottom side of door, and bottom trim on top side

of door.

➢ Locate hinge hole corner of trim.

Install hinge hole corner of trim on hinge side first, then install handle edge of trim.

8. Proceed to How to Replace the Hinges, Door and Drawer.

ENGLISH FRANÇAIS ESPAÑOL

How to connect the water supply

To reduce the risk of injury or death, follow basic precautions, including the following:

➢ Read all instructions before

installing device.

➢ DO NOT attempt installation if

instructions are not understood or if they are beyond personal skill level.

➢ Observe all local codes and

ordinances.

➢ DO NOT service device unless

specifically recommended in Use and Care Guice or published user-repair instructions.

➢ Disconnect power to refrigerator

prior to installing device.

WARNING

To avoid property damage or possible injury, follow basic precautions, including the following:

➢ Consult a plumber to connect

copper tubing to household plumbing to assure compliance with local codes and ordinances.

➢ Confirm water pressure to water

valve is between 20 and 100 pounds per square inch. If water filter is installed, water pressure to water valve must be a minimum of 35 pounds per square inch.

➢ DO NOT use a self-piercing, or

⁄16"

saddle valve! Both reduce water flow, become clogged with time, and may cause leaks if repair is attempted.

➢ Tighten nuts by hand to prevent

cross threading. Finish tightening nuts with pliers and wrenches. Do not overtighten.

➢ Wait 24 hours before placing

refrigerator into final position to check and correct any water leaks.

CAUTION

MATERIALS NEEDED

➢

⁄4" outer diameter flexible copper

tubing

➢ Brass compression nut and sleeve for

⁄4" outer diameter copper tubing.

➢ Shut-off valve (requires a

⁄4" hole to

be drilled into water supply before valve attachment)

➢ Adjustable wrench ➢

⁄4" hex nut driver

NOTE: Add 8' to tubing length needed to

reach water supply for creation of service loop.

1. Create service loop with tubing using care to avoid kinks in tubing.

2. Remove plastic cap from water valve inlet port.

3. Place brass nut (A) and sleeve (B) on copper tube end as illustrated.

4. Place end of copper tubing into water valve inlet port. Shape tubing slightly – DO NOT KINK – so that tubing feeds straight into inlet port.

5. Slide brass nut over sleeve and screw nut into inlet port. Tighten nut with wrench.

IMPORTANT: DO NOT overtighten.

Cross threading may occur.

6. Pull on tubing to confirm connection is secure. Connect tubing to frame with water tubing clamp (C) and turn on water supply. Check for leaks and correct, if present.

7. Monitor water connection for 24 hours. Correct leaks, if necessary.

Installing your refrigerator,

cont.

How to level your refrigerator

If your refrigerator requires an ice maker water supply connection, proceed to

How to Connect the Water Supply

section (page 9) before leveling your refrigerator.

To protect personal property or refrigerator from damage, observe the following:

➢ Protect soft vinyl or other flooring

with cardboard, rugs, or other protective material.

➢ Do not use power tools when

performing leveling procedure.

CAUTION

MATERIALS NEEDED

➢

⁄8" hex head driver

➢ Level

1. Remove toe grille and bottom bracket covers.

2. Turn left and right adjustment screws (A) to raise or lower front of refrigerator.

➢ Make sure

refrigerator cabinet is level from side to side by adjusting left and right roller adjustment screws.

➢ Turn stabilizing leg clockwise until

firmly against floor.

3. After completing the above listed steps, turn roller adjustment screws (A) 2 to 3 times counterclockwise, so that full weight of refrigerator rests on stabilizing legs.

4. Using a level, make sure front of refrigerator is

⁄4" (6 mm) or 1⁄2 bubble

higher than back of refrigerator.

➢ See step 3 for assistance.

5. Replace toe grille and bracket covers. See markings on inside of toe grille to insure proper placement.

➢ Snap bottom portion into place

first. Press down on top part of

grille until top portion snaps into place.

ENGLISH FRANÇAIS ESPAÑOL

Setting and maintaining proper temperatures

The controls are located at the top front of the refrigerator and freezer compartments. NOTE: The freezer control turns the cooling

system on. Neither section will cool if freezer control is set to OFF.

Refrigerator Control

Freezer Control

Initial control settings

1. Locate refrigerator control at the top of fresh food compartment and freezer control at top of freezer section.

2. The manufacturer’s recommended setting for both compartments is 4.

3. Let the refrigerator run at least 8 to 12 hours before adding food.

4. Allow 24 hours for temperature to stabilize.

Adjusting the controls

➢ 24 hours after adding food, you may

decide that one or both compartments should be colder or warmer. If so, adjust the control(s) as indicated in the Temperature Control Guide.

➢ Do not change either control more

than one number at a time.

➢ Allow 5-8 hours for temperatures to

stabilize.

➢ Changing either control will have

some effect on the temperature of the other compartment.

TEMPERATURE CONTROL GUIDE

Refrigerator too warm Turn the refrigerator control to next higher number. Refrigerator too cold Turn the refrigerator control to next lower number. Freezer too warm Turn the freezer control to next higher number. Freezer too cold Turn the freezer control to next lower number. To turn refrigerator OFF Turn the freezer control to OFF.

NOTE: Turning freezer control to OFF stops cooling in both compartments. It does not shut off power to the refrigerator.

Fresh food storage

➢ The fresh food compartment of a

refrigerator should be kept between 34° F and 40° F with an optimum temperature of 37° F. To check the temperature, place an appliance thermometer in a glass of water and place in the center of the refrigerator. Check after 24 hours. If the temperature is above 40° F adjust the control as explained above.

Frozen food storage

➢ The freezer compartment of a

refrigerator should be kept at approximately 0° F. To check the temperature, place an appliance thermometer between the frozen packages and check after 24 hours. If the temperature is above 0° F, adjust the control as described above.

About your water filter…

Water filter installation and removal

To avoid serious illness or death, do not use refrigerator where water is unsafe or of unknown quality without adequate disinfection before or after use of filter.

WARNING

➢ Bypass cartridge DOES NOT filter

water. Be sure to have replacement cartridge available when filter change is required.

➢ If water filtration system has been

allowed to freeze, replace filter cartridge.

➢ If system has not been used for

several months, and water has an unpleasant taste or odor, flush system by dispensing 2–3 glasses of water. If unpleasant taste or odor persists, change filter cartridge.

CAUTION

INSTALLING WATER FILTER

1. Remove blue bypass cap and retain for possible later use.

2. Remove sealing label from end of filter and insert into filter head.

3. Rotate gently clockwise until filter stops, and snap filter cover closed.

4. Reduce water spurts by flushing air from system. Run water continuously for 2 minutes through dispenser until water runs steady.

➢ Additional flushing may be

required in some households where water is of poor quality.

REPLACING WATER FILTER

IMPORTANT: Air trapped in system

may cause water and cartridge to eject. Use caution when removing.

1. Turn filter counterclockwise until it releases from filter head.

2. Drain water from filter into sink, and dispose in normal household garbage.

3. Wipe up excess water in filter cover

and continue with Installing Water Filter, steps 2 and 3.

WHEN DO I CHANGE THE WATER FILTER?

The filter should be changed approximately every 6 months.

IMPORTANT: Condition of water and

amount used determines life span of water filter cartridge. If water use is high, or if water is of poor quality, replacement may need to take place more often.

HOW DO I ORDER A REPLACEMENT FILTER CARTRIDGE?

Kenmore®replacement water filter cartridge model 9005 is available through Sears dealers and servicers. You may also order through Sears by using the information on the back cover.

I'M TRYING TO DISPENSE WATER TO FLUSH THE SYSTEM. WHERE'S THE WATER?

During initial use, allow about a 1 to 2 minute delay in water dispersal to allow internal water tank to fill.

WHAT IF I CHOOSE NOT TO USE THE WATER FILTRATION SYSTEM?

Dispenser feature may be used without water filter cartridge. If you choose this option, replace filter with blue bypass cap.

ENGLISH FRANÇAIS ESPAÑOL

GENERAL USE CONDITIONS

Read this Performance Data Sheet and compare the capabilities of this refrigerator with your actual water treatment needs.

DO NOT use this product where water is microbiologically unsafe or of unknown quality without adequate disinfection installed before or after filtration system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts.

Use only with cold water supply. Check for compliance with the state and local laws and regulations.

The retractable water filtration system uses a 9005 replacement cartridge (see Sears contact information at the back of your Use and Care Guide to order). Timely replacement of filter cartridge is essential for performance satisfaction from this filtration system. Please refer to the applicable section in this Use and Care Guide for general operation, maintenance requirements and troubleshooting.

This system has been tested according to ANSI/NSF 42 and 53 for reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in ANSI/NSF 42 and 53.

*Tested using a flow rate of 0.75 GPM (2.83 L/min.) and a maximum pressure of 120 psi (827 kPa)

under standard laboratory conditions, however, actual performance may vary. Health Claim Performance tested and certified by NSF International

** Particle size range classification of test. Particles used were 0.5 –1 microns.

Influent Challenge Effluent Average % Maximum Min. Required Inlet

Substance Concentration Average Reduction Effluent Reduction pH

Lead 0.15 mg/L +/- 10% 0.001 mg/L 99.33% 0.001 mg/L 0.010 mg/L 6.5

Lead 0.15 mg/L +/- 10% 0.002 mg/L 98.66% 0.003 mg/L 0.010 mg/L 8.5

Cyst Minimum 50,000/L 1count/mL 99.99% 3 count/mL > 99.95% NA

Turbidity 11+/-1 NTU 0.12 NTU 98.98% 0.18 NTU 0.5 NTU NA

Lindane 0.002 mg/L +/- 10% 0.00005 mg/L 97.62% 0.00005 mg/L 0.00002 mg/L NA

Atrazine 0.009 mg/L +/- 10% 0.0002 mg/L 97.93% 0.0006 mg/L 0.003 mg/L NA

Chlorine 2.0 mg/L +/- 10% 0.09 mg/L 95.26% 0.17 mg/L ≥75% NA

Particulate** at least 10,000 900 count/mL 99.68% 2400 count/mL ≥85% NA

particles/mL

2,4-D 0.210 mg/L +/- 10% 45.45 ug/L 84.42% 100 ug/L 0.0017 mg/L NA

Asbestos

107to 108fibers/L; fibers greater

0.16 MFL/mL 99.96% 0.16 MFL/mL 99% NA

than 10 micrometers in length

PERFORMANCE DATA

Water filter data

SYSTEM SPECIFICATION AND PERFORMANCE DATA SHEET REFRIGERATOR WATER FILTER CARTRIDGE MODEL 9005

Specifications

Service Flow Rate (maximum) ...............................................0.75 GPM (2.83 L/min)

Rated Service Life Model 9005 (maximum)...........................500 gallons/1892 liters

Maximum Operating Temperature..........................................100° F/38° C

Minimum Operating Temperature...........................................33° F/1° C

Minimum Pressure Requirement............................................35 psi/138 kPa

Maximum Operating Pressure ...............................................120 psi/827 kPa

1000 Apollo Road Eagan, Minnesota U.S.A. EPA EST #35917-MN-1

Standard No. 53: Health Effects

Chemical Reduction Unit Lead, Atrazine, Lindane and 2, 4-D Reduction Mechanical Filtration Unit Cyst, Turbidity and Asbestos Reduction

Te sted and certified by NSF International against ANSI/NSF Standards 42 and 53 in models WF50-KNI300 and WF50-KWI500 for the reduction of:

Standard No. 42: Aesthetic Effects

Taste and Odor Reduction Chlorine Reduction Mechanical Filtration Unit Particulate Reduction Class 1

Door storage

DAIRY CENTER

The Dairy Center

provides convenient storage for items such as butter, yogurt, cheese, etc. This compartment is an adjustable feature located in the door. It can be moved to several different locations to accommodate storage needs.

➢ To remove, open dairy door, pull

upward and tilt out.

➢ To install, reverse above procedure.

DOOR BUCKETS

Door Buckets adjust to

meet individual storage needs.

➢ To remove,

slide bucket up and pull straight out.

➢ To install, reverse above procedure.

Fresh food features

Water dispenser

A Water Dispenser

is located on the left side wall of the fresh food section. This design is for cold water dispensing only.

To dispense water:

➢ Hold container under spout and press

dispenser pad, as illustrated.

Interior shelves

To avoid personal injury or property damage, observe the following:

➢ Confirm shelf is secure before

placing items on shelf.

➢ Handle tempered glass shelves

carefully. Shelves may break suddenly if nicked, scratched, or exposed to sudden temperature change.

CAUTION

SPILLPROOF SHELVES

Spillproof Shelves hold

simple spills for easier cleaning.

➢ To remove shelves, lift

up and out.

➢ To install shelves, reverse above

procedure.

Spillproof Slide-out Shelves feature

the convenience of easy cleaning with a pullout design to reach items in the back. For ease of cleaning, glass shelf may be removed by pulling to full extension and lifting out of frame.

DOOR RETAINER

Door Retainers remove for easy

cleaning.

➢ To remove, slide retainer up and pull

straight out.

➢ To install, reverse above procedure.

ENGLISH FRANÇAIS ESPAÑOL

Climate-controlled drawers

HUMIDITY-CONTROLLED CRISPER DRAWERS

The Crisper Drawer keeps produce

fresh longer by providing an environment with adjustable humidity.

Controls

The crisper controls regulate the amount of humidity in the crisper

drawer. Use the low setting for produce with outer skins. Use the high setting for

leafy produce.

To remove and install crisper drawers:

➢ To remove

drawer, pull drawer out to full extension. Tilt up front of drawer and pull straight out.

➢ To install, insert drawer into frame

rails and push back into place.

WHAT CAN I DO TO PROLONG THE LIFE OF MY PRODUCE?

Please observe the following rules when storing produce in humidity-controlled crisper drawers:

➢ DO NOT wash produce before

placing in crispers. Any additional moisture added to the drawers may cause produce to prematurely spoil.

➢ DO NOT line crispers with paper

towels. Towels will retain moisture.

➢ Follow control instructions carefully.

Not setting controls correctly may damage produce.

See below for correct humidity drawer control settings:

LOW • cauliflower • apples

• corn • oranges

• zucchini • grapes

• cucumbers

HIGH • lettuce • asparagus

• spinach • cabbage

• celery • broccoli

• fresh sprouts • fresh herbs

HOW DO I REMOVE THE GLASS AND CRISPER FRAME IF I WANT TO CLEAN IT?

➢ Remove the drawers as instructed. ➢ Place hand beneath frame to push up

glass from underneath. Lift glass out.

➢ Lift frame from refrigerator liner rails. ➢ To install, replace frame on liner rails

and insert glass into grooves on top of frame.

STORAGE DRAWER

The Storage Drawer can be used for

large party trays, deli items or beverages.

To remove and install drawer:

➢ To remove drawer, pull drawer out to

full extension. Tilt up front of drawer and pull straight out.

➢ To install, insert drawer into frame

rails and push back into place.

Freezer features

Automatic ice maker

Using Ice Maker for the First Time

1. Confirm ice bin is in place and ice maker arm is down.

2. After freezer section reaches between 0° to 2° F (-18° to -17° C), ice maker fills with water and begins operating.

3. Allow approximately 24 hours after installation to receive first harvest of ice.

4. Discard ice created within first 12 hours of operation to verify system is flushed of impurities.

To avoid property damage, observe the following:

➢ Do not force ice maker arm down

or up.

➢ Do not place or store anything in

ice storage bin.

CAUTION

To prevent accidental child entrapment or suffocation risk, DO NOT remove the divider in the top freezer basket.

DANGER

Drawers

PULLOUT DRAWER BASKETS

(Door assembly of drawer removed from illustration for visual clarity)

To remove and replace baskets:

➢ See page 7 for basket removal and

page 8 for replacement instructions.

Operating Instructions

1. Confirm ice bin is in place and ice maker arm is down.

2. After freezer section reaches 0° to 2° F (-18° to -17° C), ice maker fills with water and begins operating. You will have a complete harvest of ice approximately every 3 hours.

3. Stop ice production by raising ice maker arm until click is heard.

4. Ice maker will remain in the off position until arm is pushed down.

ENGLISH FRANÇAIS ESPAÑOL

Hints and care

PART DO

➢ Use 4 tablespoons of baking soda dissolved in 1 quart

(1 liter) warm soapy water.

➢ Rinse surfaces with clean warm water and dry immediately

to avoid water spots.

➢ Use warm, soapy water and a soft, clean cloth or sponge. ➢ Rinse surfaces with clean warm water and dry immediately

to avoid water spots.

➢ Use a vacuum cleaner hose nozzle.

➢ Use a vacuum cleaner hose nozzle with brush attachment.

➢ Follow removal and installation instructions from appropriate

feature section.

➢ Allow items to adjust to room temperature. ➢ Dilute mild detergent and use a soft clean cloth or sponge

for cleaning.

➢ Use a plastic bristle brush to get into crevices. ➢ Rinse surfaces with clean warm water. ➢ Dry glass and clear items immediately to avoid spots.

DO NOT USE

➢ Abrasive or harsh cleaners ➢ Ammonia ➢ Chlorine bleach ➢ Concentrated detergents or

solvents

➢ Metal or plastic-textured

scouring pads

➢ Abrasive or harsh cleaners ➢ Ammonia ➢ Chlorine bleach ➢ Concentrated detergents or

solvents

➢ Metal or plastic-textured

scouring pads

➢ Vinegar-based products ➢ Citrus-based cleaners

➢ Abrasive or harsh cleaners ➢ Metal or plastic-textured

scouring pads

➢ A dishwasher

Textured Doors and Exterior

Cabinet Interior

Stainless Steel Doors and Exterior* IMPORTANT: Damage

to stainless steel finish due to improper use of cleaning products or non-recommended products is not covered under this product’s warranty.

Door Gaskets

Condenser Coil

Remove base grille to access

Condenser Fan Outlet Grille

See back of refrigerator Accessories Shelves,

buckets, drawers, etc.

To avoid personal injury or property damage, observe the following:

➢ Read and follow manufacturer’s directions for all cleaning products. ➢ DO NOT place buckets, shelves or accessories in dishwasher. Cracking or

warping of accessories may result.

CAUTION

To avoid electrical shock which can cause severe personal injury or death, disconnect power to refrigerator before cleaning. After cleaning, connect power.

WARNING

How to clean your refrigerator

*Astainless steel cleaner has been included inside the refrigerator for your use. To purchase additional cleaner, please contact

Sears using the information on the back of your guide.

How to remove odors from refrigerator

1. Remove all food.

2. Disconnect refrigerator.

3. Clean the following items–paying special attention to crevices–using

the appropriate instructions in How to Clean Your Refrigerator:

•Walls, floor and ceiling of cabinet

interior.

• Drawers, shelves and gaskets.

4. Wash and dry all bottles, containers and jars. Discard spoiled or expired items.

5. Wrap or store odor-causing foods in tightly-sealed containers to prevent reoccurring odors.

6. Connect power to refrigerator and return food.

7. After 24 hours, check if odor has been eliminated.

If odor is still present...

1. Remove drawers and place on top shelf of refrigerator.

2. Pack refrigerator and freezer sections–including doors–with crumpled sheets of black and white newspaper.

3. Place charcoal briquettes randomly on crumpled newspaper in both freezer and refrigerator compartments.

4. Close doors and let stand 24–48 hours.

5. Repeat steps 5 through 7 above.

If odor was not eliminated, contact Sears Service Center. Refer to back of manual for phone number.

Energy saving ideas

➢ Avoid overcrowding refrigerator

shelves. This reduces effectivity of air circulation around food and causes refrigerator to run longer.

➢ Avoid adding too much warm food to

refrigerator at one time. This overloads compartments and slows rate of cooling.

➢ Do not use aluminum foil, wax paper,

or paper toweling as shelf liners. This decreases air flow and causes refrigerator to run less efficiently.

➢ A freezer that is

⁄3 full runs most

efficiently.

➢ Locate refrigerator in coolest part of

room. Avoid areas of direct sunlight, or near heating ducts, registers, or other heat producing appliances. If this is not possible, isolate exterior by using a section of cabinet or an added layer of insulation.

➢ Refer to section in Use and Care

Guide on temperature controls for recommended control settings.

➢ Clean door gaskets every three

months according to Use and Care Guide instructions. This will assure that door seals properly and refrigerator runs efficiently.

➢ Take time to organize items in

refrigerator to reduce time that door is open.

➢ Be sure your doors are closing

securely by leveling refrigerator as instructed in your Use and Care Guide.

➢ Clean condenser coils off as

indicated in the Use and Care Guide every 3 months. This will increase energy efficiency and cooling performance.

To avoid personal injury or property damage, observe the following:

➢ Allow light bulb to cool. ➢ Wear gloves when replacing light

bulb.

CAUTION

To avoid electrical shock which can cause severe personal injury or death, disconnect power to refrigerator before replacing light bulb. After replacing light bulb, connect power.

WARNING

How to remove and replace light bulbs

FRESH FOOD

1. Slide shield toward back of compartment to release from light assembly.

2. Remove light bulbs.

3. Replace with appliance bulbs no

greater than 40 watts.

4. Replace light bulb cover by inserting tabs on light shield into liner holes on each side of light assembly. Slide shield toward front of refrigerator until

it locks into place. DO NOT force

shield beyond locking point. Doing so may damage light shield.

FREEZER

1. Pinch rear tabs on light cover and pull straight down.

2. Remove light bulb.

3. Replace bulb with

appliance bulb no greater than 40

watts.

4. Insert front tabs of light cover into freezer liner and snap rear portion over light assembly until rear tabs engage.

Hints and care,

cont.

ENGLISH FRANÇAIS ESPAÑOL

Normal operating sounds

Today’s refrigerators use foam insulation and are more energy efficient than refrigerators of the past. However, foam insulation is not as sound absorbent as former insulated models. As a result, certain sounds may be unfamiliar. In time, these sounds will become familiar. Please refer to this information before calling service.

SOLUTION

➢ Normal operation

➢ See Installation Instructions for details on how to level your

refrigerator.

➢ Normal operation

➢ Stop sound by raising ice maker arm to ‘off’ position. See

Automatic Ice Maker section in your Use and Care Guide

for details.

➢ Normal operation

POSSIBLE CAUSE

➢ Freezer control (A) clicks when

starting or stopping compressor.

➢ Defrost timer (B) sounds like an

electric clock and snaps in and out of defrost cycle.

➢ Freezer fan (C) and condenser

fan (D) make this noise while

operating.

➢ Evaporator (E) and heat

exchanger (F) refrigerant makes

this noise when flowing.

➢ Ice cubes from ice maker (select

models) drop into ice bucket (G).

➢ Compressor (H) makes a

pulsating sound while running.

➢ Refrigerator is not level.

➢ Ice maker water valve (I)

hookup (select models) buzzes when ice maker fills with water.

➢ Ice maker (J) is in the ‘on’

position without water connection.

➢ Compressor (H) can make a high-

pitched hum while operating.

➢ Defrost heater (K) hisses, sizzles

or pops when operational.

TOPIC

Clicking

Air rushing or whirring

Gurgling or boiling sound

Thumping

Vibrating noise

Buzzing

Humming

Hissing or popping

PROBLEM Food temperature

appears too warm

Refrigerator has an odor

Water droplets form on outside of refrigerator

Water droplets form on inside of refrigerator

Refrigerator or ice maker make unfamiliar sounds or seems too loud

Crisper drawers do not close freely

Refrigerator runs too frequently

Operation

POSSIBLE CAUSE

Door is not closing properly.

Controls need to be adjusted.

Condenser coils are dirty.

Rear air grille is blocked.

Door has been opened frequently, or has been opened for long periods.

Food has recently been added.

Compartment is dirty or has odor-causing food.

Check gaskets for proper seal.

Humidity levels are high.

Controls require adjustment.

Humidity levels are high or door has been opened frequently.

Check gaskets for proper seal.

Normal operation.

Contents of drawer, or positioning of items in the surrounding compartment could be obstructing drawer.

Drawer is not in proper position.

Refrigerator is not level.

Drawer channels are dirty or need treatment.

Doors have been opened frequently or have been opened for long periods of time.

Humidity or heat in surrounding area is high. Food has recently been added.

Refrigerator is exposed to heat by environment or by appliances nearby.

Condenser coils are dirty.

SOLUTION See Installing Your Refrigerator–How to Level Your

Refrigerator section on how to properly level refrigerator.

Check gaskets for proper seal. Clean, if necessary, according to cleaning instructions.

Check for internal obstructions that are keeping door from closing properly (i.e. improperly closed drawers, ice buckets, oversized or improperly stored containers or foodstuffs, etc.)

See Setting and Maintaining Proper Temperatures– Adjusting the Controls section on how to adjust your controls.

See section on Hints and Care–How to Clean Your Refrigerator for instructions.

Check the positioning of food items in refrigerator to make sure grille is not blocked. Rear air grilles are located under crisper drawers.

Reduce time door is open. Organize food items efficiently to assure door is open for as short a time as possible.

Allow interior environment to adjust for period the door has been open.

Allow time for recently added food to reach refrigerator or freezer temperature.

See section on Hints and Care for instructions.

See section on Hints and Care–How to Clean Your Refrigerator for instructions.

See Setting and Maintaining Proper Temperatures– Adjusting the Controls section on how to adjust your controls.

See Setting and Maintaining Proper Temperatures– Adjusting the Controls section on how to adjust your controls. Reduce time door is open. Organize food items efficiently to assure door is open for as short a time as possible.

See section on Hints and Care–How to Clean Your Refrigerator for instructions.

Refer to Normal Operating Sounds.

Reposition food items and containers to avoid interference with the drawers.

See section on Fresh Food Features–Climate-Controlled Drawers to verify drawer positioning.

See Installing Your Refrigerator–How to Level Your Refrigerator section on how to properly level refrigerator.

Clean drawer channels with warm, soapy water. Rinse and dry thoroughly. Apply a thin layer of petroleum jelly to drawer channels.

Reduce time door is open. Organize food items efficiently to assure door is open for as short a time as possible.

Allow interior environment to adjust for period the door has been open.

Normal operation. Allow time for recently-added food to reach refrigerator or

freezer temperature. Evaluate your refrigerator’s environment. Refrigerator may

need to be moved to run more efficiently. See section on Hints and Care–How to Clean Your

Refrigerator for instructions.

Troubleshooting

+ 44 hidden pages

Kenmore Elite 59672282201, 59672282202, 59672283201, 59672283202, 59672284201 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual