Kenmore Elite 11057826600, 11057827600, 11057828600, WHP1500SU0, WHP1500ST0 Installation Guide

...

KltchenAid ¸®

HOME APPLIANCES

Superba °

2TM TM 4TM

sport

Table of Contents/(ndice/TaMe des matieres .............................................. 2/8/14

27 j_

(68.6 cm)

151/2"

(33 cm)

W10050180 Rev. A

TABLE OF CONTENTS

PEDESTAL SAFETY ................................... 2

iNSTALLATiON REQUIREMENTS ........................ 3

Tools and Parts ...................................... 3

Location Requirements ................................ 3

Before Installing Your Pedestal ........................ 3

iNSTALLATiON iNSTRUCTiONS ......................... 5

InstaUingthe Pedestal ............................... 5

PEDESTAL USE ...................................... 6

WARRANTY .......................................... 7

PEDESTAL SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

This is the safety alert symbol.

These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

iNSTALLATiON REQUIREMENTS

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

Tools needed

[] Utility knife [] 1/4"hex-head ratchet or

open-end wrench (leveling legs)

[] _A6"hex-head ratchet or

nut driver (for sheet metal

SCreWS)

[] 9A6"open-end wrench

(for leveling leg Iocknuts)

[] Pliers or slip-joint pliers

(for drain and inlet hoses)

[] Level [] Bucket

Parts supplied Remove the parts package from the pedestal drawer. This

package contains 4, #12 x %" hex head sheet metal screws, drawer divider, and drawer shelf.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline,

away from dryer. Place dryer at least 18 inches (46 cm) above the floor for

a garage installation.

Failure do to so can result in death, explosion, or fire.

iMPORTANT: If your washer and dryer are already installed, they

must be uninstalled. If you need to uninstall your washer or dryer, see your Installation

Instructions that came with your model for tools required. Uninstalling Your Washer

Excessive Weight Hazard

Use two or more people to move and uninstall washer. Failure to do so can result in back or other injury.

Turn off the hot and cold water faucets.

Unplug the power supply cord or disconnect power.

Slowly loosen the fill hoses at the faucets to relieve the water pressure. Use a sponge or towel to absorb the released water.

Remove the hot and cold fill hoses from the back of the

washer. Drain the water from the hoses into a bucket. Squeeze the ears of the drain hose clamp with pliers to open

and slide the clamp down the hose. Disconnect the drain hose from the washer and drain any water in the hose into a

bucket.

Pull the washer away from wall so it can be tipped on its

back. _::_.....

Protect the floor with a large piece of cardboard cut from the

pedestal carton, Lay the washer on its back (make sure that the power supply cord is not under the washer) so that the

cardboard is under the entire lower back edge of the washeE An additional small amount of water will drain out of the

washer when it is tipped back,

NOTE: If dryer and pedestal assembly is located in a garage, 3" (7.6 cm) must be added under pedestal so that dryer is

18" (46 cm) above garage floor.

(30.5 cm

12"-_

15"

8. Go to "Installing the Pedestal" section.

Uninstalling Your Electric Dryer t. Unplug the power supply cord.

Electrical Shock Hazard

Disconnect power before servicing. Replace all parts and panels before operating, Failure to do so can result in death or electrical shock.

3. Pull the dryer away from the wall enough to loosen the vent clamp. Loosen the clamp and gently remove the exhaust vent

from the dryer exhaust outlet.

4. Disconnect the flexible gas supply line from the dryer. Put a piece of tape over the open ends of the gas line connection

fittings.

5. Pull the dryer away from wall so that it can be tipped onto its back.

6. Protect the floor with a large piece of cardboard cut from the pedestal carton. Lay the dryer on its back (make sure that the

power supply cord is not under the dryer) so that the cardboard is under the entire lower back edge of the dryer.

2. Disconnect wiring if dryer is direct wired.

Excessive Weight Hazard

Use two or more people to move and uninstall dryer. Failure to do so can result in back or other injury.

3. Pull the dryer away from the wall enough to loosen the vent clamp. Loosen the clamp and gently remove the exhaust vent

from the dryer exhaust outlet.

4. Pull the dryer away from wall so that it can be tipped onto its back.

5. Protect the floor with a large piece of cardboard cut from the pedestal carton. Lay the dryer on its back (make sure that the

power supply cord is not under the dryer) so that the cardboard is under the entire lower back edge of the dryer.

(30.5era)

12"_

12"

(30.5 cm)

18"

(38.1 cm)

7. Go to "Installing the Pedestal" section. Washer or Dryer is in its Packaging

Excessive Weight Hazard

Use two or more people to move washer or dryer. Failure to do so can result in back or other injury.

Position the packaged washer or dryer close to its final

position. Cut the packaging as follows: Washer: Cut plastic film along dotted cut line around the

base. Do not remove the packaging.

Dryer: Cut carton around top and down corners along dotted

cut lines. Lay all four carton sides on floor. Discard carton top and corner posts.

IMPORTANT: Leave carton bottom underneath dryer.

(38.1 cm)

6 Go to "installing the Pedestal" section. Uninstalling Your Gas Dryer

Excessive Weight Hazard

Use two or more people to move and uninstall dryer, Failure to do so can result in back or other injury,

t. Unplug the power supply cord or disconnect power.

2. Turn off the gas supply.

A. Ca#on sides

Lay washer or dryer on its back. NOTE: When laying the washer on its back, hold the bottom

cap down on the floor. Do not remove the plastic film, corner posts or top cap. These protect the floor and washer back.

When laying the dryer on its back, the floor and dryer back are protected by pieces of the carton.

iNSTALLATiON iNSTRUCTiONS

Follow these instructions to install the pedestal on a washer or dryer.

Excessive Weight Hazard

Use two or more people to move and install pedestal. Failure to do so can result in back or other injury.

t. Open the pedestal drawer as far as possible and remove the

contents. This package contains 4, #12 x %" hex head sheet metal screws used in step 5, and the shelf and divider pack.

Pull the lever up on the left side of the drawer and at the

same time, push the lever down on the right side. While holding the levers in position, pull the drawer all the way out

and set aside. Push the slides back into the pedestal.

A. Lever (M'qhts/de shown)

5. If your washer or dryer has feet installed, remove them. Do not install the feet that came with a new washer or dryer.

6. Partially install 2 of the #12 x %" hex head sheet metal screws in the lower holes. Leave a space of about sA"(1 cm)between

the screw head and the bottom of the washer or dryer.

A B

Verify the 4 spacer pads are installed on the top of the pedestal.

A.Spacerpads

Locate the levers on the drawer slides on each side of the drawer.

%%, j,_

A. Washer bottom B. Dryer bottom

C. Install screws

7. Tip the pedestal on its back and move it against the washer or dryer bottom. Slide the pedestal's keyhole slots over the

lower 2 partially installed screws.

8. Position the pedestal toward the front of the washer or dryer and install the 2 remaining hex-head sheet metal screws. Do

not tighten completely.

9. Align the sides of the pedestal so that they are even with the sides of the washer or dryer. Reach inside the pedestal

drawer opening and securely tighten all 4 pedestal screws.

A. Drawer s//b/e B, Lever

A.Lower screws in keyholeslots

t0.Tipthewasherordryerbacktoitsuprightposition.Remove

anddiscardpackagingincludingwasher'splasticfilm,corner

postsandtopcap. tl. Slidethewasherordryerclosetoitsfinallocation. t2.FollowtheInstallationInstructionsthatcamewithyourmodel

tofinishinstallingorreinstallingyourwasherordryer(hoses,

vents,etc.). t3.Levelthewasherordryerfromsidetosideandfronttoback.

NOTE:Makesureall4pedestalfeetareinsolidcontactwith

thefloor.

Placealevelonthetop.Locatethe1/4"hex-headscrewson

thetopofeachpedestalfoot.Reachinsidethepedestaland

usea1/4"hex-headratchetoropen-endwrenchtoadjustthe

feetupordownasneededtolevelthewasherordryer.

t4.Whenthewasherordryerislevel,usea9/16"open-end

wrenchtosecurelytightenall4Iocknutsagainstthepedestal.

TheIocknutsmustbetightenedtopreventvibration.

t7. Place the divider in the drawer at the desired location.

NOTE: Use of the divider is optional. See "Pedestal Use" section.

t8. Place the shelf on top of the drawer with the handle facing

forward. Close the drawer.

PEDESTAL USE

Your pedestal has several uses.

The drawer may be used to store detergent and other laundry

supplies and is equipped with a removable divider.

A ....................................

A.Locknuts

t5. Reinstall the drawer by lining up the drawer slides with the

slides inside the pedestal. Push the drawer slides in until they

lock in place.

t6. Remove the shelf and divider from the bag.

The shelf will support a laundry basket to assist with loading and

unloading of the washer and dryer.

The shelf can be slid front to back or removed. The shelf is equipped with a removable compartment to store

dryer sheets in.

0000000

+ 14 hidden pages