Kenmore Elite 10651772510, 10651773510, 10651779510, 10651779511 Owner’s Manual

Use & Care Guide Manual de uso y cuidado

Guide d'utilisation et d'entretien

English / Espafiol / Fran_ais

Models/Modelos/Mod_les: 106.5177"

I<enmoreElite

= color number_, n6mero de colo_, le num@o de la couleur

P/N W10768950C Sears Brands Management Corporation

Hofl:man Estates, IL, U.S.A. 60179 www.kenmore.com

www.sears.com Sears Canada Inc.

Toronto, Ontario, Canada M5B 2C3 www.sears.ca

TABLE OF CONTENTS

PROTECTION AGREEMENTS .................................................................... 2

KENMORE ELITE_ LIMITED WARRANTY ................................................... 3

REFRIGERATOR SAFETY .......................................................................... A

INSTALLATION INSTRUCTIONS ............................................................... 5

Unpack the Refrigerator ..................................................................................... 5

Door Removal, Leveling and Alignment .......................................................... 6

Handle Installation and Removal ...................................................................... 9

Location Requirements ...................................................................................... 10

Electrical Requirements ..................................................................................... 10

Water Supply Requirements ............................................................................ 10

Connect Water Supply ...................................................................................... 11

Prepare the Water System ................................................................................ 13

Install CleanFIow TM Air Filters ........................................................................... 13

Install Crisperl<eeper TM Produce Preserver .................................................... 14

REFRIGERATOR USE ............................................................................... 16

Ensuring Proper Air Circulation ......................................................................... 16

Using the Controls ............................................................................................... 16

Water and Ice Dispensers ................................................................................. 18

Water Filtration System ..................................................................................... 21

Ice Maker and Storage Bin .............................................................................. 22

REFRIGERATOR FEATURES ..................................................................... 23

Refrigerator Door Bins ....................................................................................... 23

Bottle/Can Rack ................................................................................................. 23

PROTECTION AGREEMENTS

Refrigerator Shelves .......................................................................................... 23

Wine Rack .......................................................................................................... 23

Dell Drawer ......................................................................................................... 23

Convertible Vegetable/Meat Drawer, Crisper and Covers ...................... 24

Convertible Vegetable/Meat Drawer Temperature Control .................... 24

Crisper Humidity Control .................................................................................. 24

Utility Bin ............................................................................................................. 24

FREEZER FEATURES ................................................................................ 24

Freezer Door Bins ............................................................................................... 25

Freezer Shelf ....................................................................................................... 25

Freezer Bin ........................................................................................................... 25

REFRIGERATOR CARE ............................................................................ 25

Cleaning .............................................................................................................. 25

Lights .................................................................................................................... 26

Power Interruptions ............................................................................................ 26

Vacation and Moving Care ............................................................................. 26

PROBLEM SOLVER .................................................................................. 27

ACCESSORI ES......................................................................................... 30

PERFORMANCE DATA SHEET ................................................................. 31

SERVICE NUMBERS .............................................................. BACK COVER

JNDICE .................................................................................................... 32

TABLE DES MATIERES ............................................................................ 65

Master Protedion Agreements

Congratulations on making a smart purchase. Your new I(enmore _ product is designed and manufactured for years of dependable operation. But like all products, it may require preventive maintenance or repair from time to time. That's when having a Master Protection Agreement can save you money and aggravation.

The Master Protection Agreement also helps extend the life of your new product. Here's what the Agreement * includes:

I/Parts and labor not just for repairing defects, but to help keep products

operating properly under normal use. Our coverage goes well beyond the product warranty. No deductibles, no functional failure excluded from coverage - real protection.

I/Expert service by a force of more than 10,000 authorized Sears service

technicians, which means someone you can trust will be working on your product.

I/Unlimited service calls and nationwide service, as often as you want us,

whenever you want us.

I/"No-lemon" guarantee - replacement of your covered product if four

or more product failures occur within twelve months.

I/Product replacement if your covered product can't be fixed.

I/Annual Preventive Maintenance Check at your request - no extra

charge.

V' Fast help by phone - we call it Rapid Resolution - phone support from

a Sears representative on all products. Think of us as a "talking owner's manual."

I/Power surge protection against electrical damage due to power

fluctuations.

*/$250 Food Loss Protection annually for any food spoilage that is the

result of mechanical failure of any covered refrigerator or freezer.

*/Rental reimbursement if repair of your covered product takes longer

than promised.

*/25% discount off the regular price of any non-covered repair service

and related installed parts.

Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night, or schedule a service appointment online.

The Master Protection Agreement is a risk free purchase. If you cancel for any reason during the product warranty period, we will provide a full refund. Or, a prorated refund anytime after the product warranty period expires. Purchase your Master Protection Agreement today!

Some limitations and exclusions apply. For prices and additional information in the U.S.A. call 1-800-827-6655.

*Coverage in Canada varies on some items. For full details call Sears

Canada at 1-800-361-6665.

Sears Installation Service

For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in the U.S.A. or

Canada call 1-800-4-MY-HOME ®.

I(ENMORE ELITE®LIMITED WARRANTY

WITH PROOF OF SALE, the following warranty coverage applies when this appliance is correctly installed, operated and maintained according to all supplied instructions.

FOR ONE YEAR from the date of sale, this appliance is warranted against defects in material or workmanship. A defective appliance will receive free repair or replacement at option of seller. This warranty coverage applies for only 90 days from the sale date in the United States, and is void in Canada, if the appliance is ever used for other than private household

purposes. FOR FIVE YEARS from the date of sale, the sealed refrigerant system of

this appliance is warranted against defects in material or workmanship. New system components will be supplied for defective ones, free of charge. You are responsible for the labor cost of component installation after the first year from the sale date. This warranty coverage applies for only one year from the sale date in the United States, and is void in Canada, if the appliance is ever used for other than private household

purposes. For warranty coverage details about obtaining free repair or replacement,

visit www.kenmore.com/warra nty. This warranty covers ONLY defects in material and workmanship, and

will NOT pay for:

1. Expendable items that can wear out from normal use, including but not

limited to filters, belts, bags or screw-in base light bulbs.

2. A service technician to clean or maintain this appliance, or to instruct

the user in correct appliance installation, operation and maintenance.

3. Service calls to correct appliance installation not performed by Sears

authorized service agents, or to repair problems with house fuses, circuit breakers, house wiring, and plumbing or gas supply systems resulting from such installation.

4. Damage to or failure of this appliance resulting from installation not

performed by Sears authorized service agents, including installation that was not in accord with electrical, gas or plumbing codes.

5. Damage to or failure of this appliance, including discoloration or

surface rust, if it is not correctly operated and maintained according to all supplied instructions.

6. Damage to or failure of this appliance, including discoloration or

surface rust, resulting from accident, alteration, abuse, misuse or use for other than its intended purpose.

Z Damage to or failure of this appliance, including discoloration or

surface rust, caused by the use of detergents, cleaners, chemicals or utensils other than those recommended in all instructions supplied with the product.

8. Damage to or failure of parts or systems resulting from unauthorized

modifications made to this appliance.

9. Service to an appliance if the model and serial plate is missing,

altered, or cannot easily be determined to have the appropriate certification logo.

Disclaimer of implied warranties; limitation of remedies

Customer's sole and exclusive remedy under this limited warranty shall be product repair or replacement as provided herein. Implied warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year on the appliance and five years on the sealed system, or the shortest period allowed by law. Seller shall not be liable for incidental or consequential damages. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitation on the duration of implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to you.

This warranty applies only while this appliance is used in the United States or Canada*.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

* In Canada, in-home repair service is not available in all areas, nor will

this warranty cover user or servicer travel and transportation expenses if this product is located in a remote area (as defined by Sears Canada

Inc.) where an authorized servicer is not available.

Sears Brands Management Corporation

Hoffman Estates, IL 60179

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2C3

PRODUCT RECORD

Record your complete model number, serial number, and purchase date. You can find this information on the model and serial number label located

on the product. Have this information available to help you obtain assistance or service

more quickly whenever you contact Sears concerning your appliance.

Model number

Serial number

Purchase date

Save these instructions and your sales receipt for future reference.

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

[] Plug into a grounded 3 prong outlet. [] Do not remove ground prong.

[] Do not use an adapter. [] Do not use an extension cord.

[] Disconnect power before servicing. [] Replace all parts and panels before operating.

[] Remove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

[] Use nonflammable cleaner. [] Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

[] Use two or more people to move and install refrigerator. [] Disconnect power before installing ice maker (on ice maker

kit ready models only).

[] Use a sturdy glass when dispensing ice (on some models). [] Do not hit the refrigerator glass doors (on some models).

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

Proper Disposal of Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are nat problems of the

past. Junked or abandoned refrigerators are still dangerous, even if they will sit for "just a few days." If you are getting rid of your old refrigerator,

please follow these instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.

INSTALLATION INSTRUCTIONS

• Leave the shelves in

_lace so that children may not easily climb inside.

important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.

Clean Before Using

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Removethe Packaging

Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information see "Refrigerator Safety."

When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.

After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in "Refrigerator

Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Gather the required tools and parts and read all instructions before starting installation. Save these instructions for future reference. NOTE= Before moving your product into your home, measure the doorway of your home to see whether you need to remove the refrigerator and freezer

doors. If door removal is necessary, see the instructions below. IMPORTANT= Before you begin, turn the refrigerator control OFF or turn cooling off. Unplug refrigerator or disconnect power. Remove food, the ice storage

bin (on some models), and any adjustable door or utility bins from doors. TOOLS NEEDED=

Bubble level, Phillips screwdriver, 3/16" hex key, 1/4" hex-head socket wrench, 1/4" and 5/16" open-ended wrenches or adjustable wrench, internal star drive or 3/8" hex-head socket wrench

Electrical Shock Hazard

Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

Wiring Connection

A B C D E F

A. P-clamp D. Wiring Clip B. Routing E. Grommets

Plate F. Wiring

C. Electrical Plugs

Housing

Water Dispenser Tubing Connection (Style 1)

Top Left Hinge

A. Do Not Remove Screws.

Door Removal

Top Right Hinge

A. Do Not Remove Screws.

Bottom Hinges

(Left and Right)

Leveling

A. Face of Fitting

A. Bottom Hinge B. Leveler Bracket

C. Leveling Foot

Water Dispenser Tubing Connection (Style 2)

Door Alignment (Bottom Right Hinge)

jS "/

A,__jI V Raise

Lower _ "_ _

A. Alignment Screw

Remove the Doors

Electrical Shock Hazard

Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

Unplug refrigerator or disconnect power.

Open both doors to 90 °. Remove the base grille by removing the two screws, and then pulling out on the outside corners. See Graphic 7.

NOTE: The doors must only be opened to 90 °. If they are opened all the way, the base grille will not come off.

Disconnect the water tubing, located behind the base grille on the freezer door side. The dispenser tubing runs through the door hinge,

and must be disconnected in order to remove the door.

• Style 1: Press the colored outer ring against the face of fitting and pull the water tubing free. See Graphic 2A.

NOTE: Keep the water tubing connector attached to the tube that runs underneath the freezer. The door cannot be removed if

the connector is still attached to the tube that runs through the door hinge.

• Style 2: Firmly pull on the clasp to release the tube, and then pull the water tubing free. See Graphic 2B.

NOTE: Keep the clasp attached to the tube that runs underneath the freezer.

Disconnect the wiring, located behind the base grille on the freezer door side. See Graphic 3.

• Remove the P-clamp using a 1/4" hex-head socket wrench. Remove the small wiring bundle from the P-clamp.

• Remove the wiring clip using a 1/4" hex-head socket wrench.

• Pull the electrical housing out from under the refrigerator. Disconnect the wiring plugs from the housing.

• Gently pull the large wiring bundle (with two white plugs) through the routing plate.

5. Close both doors and keep them closed until you are ready to lift them free from the cabinet.

6. Use a 3A6" hex key to remove the top left hinge screws as shown. See

Graphic 4.

IMPORTANT: Do not remove either screw A.

Excessive Weight Hazard

Use two or more people to lift the freezer door. Failure to do so can result in back or other injury.

Lift freezer door straight up off bottom hinge. See Graphic 5.. The water tubing and wiring remain attached to the freezer door and pull

through the bottom left hinge. NOTE: This may require two people - one to lift the door and another

to feed the water tubing and wiring through the hinge. Be sure the hole in the hinge is clear of obstructions, then gently pull one water tube

through the hinge. (Avoid kinking the tube.) Next, gently pull the other water tube through the hinge, again avoiding kinks. Finally, gently pull

the wiring bundle (including the grommet and wiring plugs) through the hinge.

IMPORTANT: Rest the door on its side on a soft, clean surface, such as a towel, blanket or piece of cardboard. This will help avoid damaging the door, water tubing and wiring.

Use a 3/16" hex key to remove the top right hinge screws as shown. See

Graphic 6.

IMPORTANT: Do not remove either screw A.

Lift the refrigerator door straight up off bottom hinge. IMPORTANT: Rest the door on its side on a soft, clean surface, such as

a towel, blanket or piece of cardboard. This will help avoid damaging the door.

10.

It may not be necessary to remove the bottom hinges to move the refrigerator through a doorway. Both bottom hinges have similar

construction.

• If necessary, use an internal star drive or a 3/8" hex-head socket

wrench to remove the bottom hinges. See Graphic Z

IMPORTANT: The leveler brackets are mounted behind the hinges. If you remove the hinges, make sure that the leveler

brackets are replaced when reinstalling the hinges.

Replace the Doors and Hinges

Replace both bottom hinges if removed. Make sure that the leveler brackets are assembled behind the hinges. Tighten screws.

IMPORTANT: When the screws are tightened properly, there should not be any gaps between the refrigerator, leveler bracket and hinge.

NOTE: There are two wiring bundles that run underneath the freezer - a large bundle with a large grommet and two white plugs at the end, and

a small bundle with a small grommet and one yellow plug at the end.

Excessive Weight Hazard

Use two or more people to lift the freezer door. Failure to do so can result in back or other injury.

Before replacing the freezer door on the bottom left hinge, feed the small wiring bundle through the hinge. Assistance may be needed.

IMPORTANT: Do not feed the large wiring bundle through the hinge. This bundle is intended to run directly from the door to the connections

beneath the freezer. Forcing the large bundle through the hinge may damage the door and/or the wiring and will keep the door from

closing properly.

3. Feed both water tubes through the bottom left hinge, then replace the freezer door on the hinge. Assistance may be needed.

NOTE: Provide additional support for the doors while the top hinges are being replaced. Do not depend on the door magnets to hold the doors in

place while you are working.

Align and replace the top left hinge as shown. See Graphic 4. Tighten screws.

Reconnect water tubing and wiring. IMPORTANT: Do not intertwine the water tubing and wiring bundles

when reconnecting them.

• Water Connection Style 1: Push the larger _6" (7.94 mm) water

tube into the blue fitting until it stops, then push the smaller 1/4" (6.35 mm) water tube into the green fitting until it stops. See

Graphic 2A.

Water Connection Style 2: Push the black water tube with the blue tip into the blue fitting until it stops. Close the clasp around the tubing, making sure it snaps into place. Repeat this process to connect the red-tipped black water tube and the red fitting. See

Graphic 2B.

• Reinstall the P-clamp around the small wiring bundle (with one

yellow plug), then replace the P-clamp on the top screw hole of the routing plate. See Graphic 3.

• Gently route the large wiring bundle (with two white plugs)

through the hole in the routing plate, so that the wiring runs behind the right side of the routing plate. See Graphic 3.

NOTE: The large wiring bundle should always remain below the small wiring bundle.

• Reconnect the wiring plugs to the electrical housing, then push the

housing back under the refrigerator. Align the left hole in the front lip of the housing with the right hole in the refrigerator's base

crossbar. See Graphic 3.

• Reinstall the wiring clip over the grommets. First install the smaller

grommet into the top of the clip, then install the larger grommet into the bottom of the clip (closest to the screw hole). See

Graphic 3.

• Align the clip's screw hole with the left hole in the electrical housing and the right hole in the crossbar° and screw in the clip

using a single screw. Tighten screw. See Graphic 3.

IMPORTANT: Once connected, the wiring bundles should not be

taut. Some flexibility is needed to allow the freezer door to open properly.

Replace the refrigerator door by lifting the door onto the bottom right hinge.

Align and replace the top right hinge as shown. See Graphic 6. Tighten screws.

Replace the ice storage bin (on some models) and any adjustable door or utility bins.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

9. Plug refrigerator into a grounded 3-prong outlet.

Leveling and Door Closing

Your refrigerator has two adjustable front feet -- one on the right and one on the left. In most cases, the refrigerator should be steady when both feet are touching the floor. If your refrigerator seems unsteady or if you want

the doors to close more easily, adjust the refrigerator's tilt using the instructions below:

1. Move the refrigerator into its final location. If necessary, open both doors to 90 ° and remove the base grille. See Graphic 1.

2. The two leveling feet are located on the brackets on each side of the product. See Graphic 8.

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling feet. This makes it easier to make adjustments.

3. Use a 1/4" open-ended or adjustable wrench to adjust the leveling feet. Turn the leveling foot to the left to raise that side of the product, or turn it to the right to lower that side of the product.

NOTE: Both leveling feet should be snug against the floor, and the rollers should not touch the floor. This keeps the refrigerator from rolling forward when opening the doors.

4. Open both doors again and check that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning the leveling feet to the left. It may take several more turns, and you should turn both leveling feet the same amount.

5. Use a bubble level to check the leveling of the refrigerator.

NOTE: Whenever you need to move the refrigerator, turn the leveling feet to the right until they are no longer touching the ground. This will allow the refrigerator to roll more easily.

Door Alignment

A refrigerator that is not level from side-to-side may appear to have doors that are not properly aligned. If the doors appear this way, use the

instructions in the previous section to check the leveling. The doors are designed to be slightly different heights when the

refrigerator is empty° in order to account for the weight of food that will be placed on the doors. If the doors are still not aligned after checking the leveling and loading the refrigerator with food, follow the steps below to adjust the door alignment.

1. If necessary, open both doors to 90 ° and remove the base grille. ,See

Graphic 1.

2. Locate the alignment screw on the bottom hinge of the refrigerator door. See Graphic 9.

3. Use a 5/16" open-ended or adjustable wrench to turn the screw. To raise the refrigerator door_ turn the screw to the right. To lower the

door, turn the screw to the left.

4. Check that the doors are even at the top. If necessary, continue to turn the alignment screw until the doors are aligned.

5. Open both doors to 90 °. Replace the base grille. See Graphic 1.

PARTS INCLUDED: Door handles (2), 1/8" hex key, spare setscrew(s)

To Install the Handles: NOTE: The handle mounting setscrews are preinstalled in the handle.

1. Remove the handles, which are packed inside the refrigerator. NOTE: To avoid scratching the finish, place the handles on a towel

or other soft surface.

2. Open the freezer door. On the refrigerator door, place the handle on the shoulder screws with the setscrews facing the freezer.

4. While holding the handle, insert the short end of the hex key into the upper hole and slightly rotate the hex key until it is engaged in the

setscrew.

Using a clockwise motion, tighten the setscrew until it begins to contact the shoulder screw.

Repeat steps 4 and 5 to begin fastening the lower setscrew.

Once both setscrews have been partially tightened as outlined in the previous steps, fully tighten both the upper and lower setscrews.

IMPORTANT: When the screws feel tight, tighten them an additional quarter-turn. The handle is not properly installed without this extra tightening.

8. Open the refrigerator door and close the freezer door. Repeat steps 2 through 7 to install the other handle onto the freezer door with the setscrews facing the refrigerator.

9. Save the hex key and all instructions.

To Remove the Handles:

1. While holding the handle, insert the short end of the hex key into the lower setscrew hole and slightly rotate the hex key until it is engaged

in the setscrew.

2. Using a counterclockwise motion, loosen the setscrew a quarter-turn at a time.

3. Repeat steps 1 and 2 for the upper setscrew. Gently pull the handle away from the door.

4. If necessary, use a Phillips screwdriver to remove the shoulder screws from the door.

A. Shoulder screws

B, Setscrews inside the handle

3°

Firmly push the handle toward the door until the handle base is flush against the door.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor household use only. To ensure proper ventilation for your refrigerator, allow for 1/2" (1.27 cm) of

space on each side and at the top. Allow for 1" (2.54 cm) of space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a fixed wall, leave a 2" (5.08 cm) minimum space on each side (depending on your model) to allow the doors to swing open.

__J

// I

V2" (1.27

- I!q

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz, AC only, 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a

switch. Do not use an extension cord. NOTE: Before performing any type of installation or cleaning, or removing

a light bulb, turn cooling off or turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF, and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and turn cooling on or reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting. See "Using the Controls" in the User Instructions, User Guide, or Use & Care Guide.

2" (5.08 cm)!

NOTES:

This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an

oven or radiator.

Normal minimum cabinet cut-out width required for product installation is 36" (91.44 cm). However, if the product is placed against an extended wall and the ability to remove the crisper pans is desired, an additional 18" (45.72 cm) of cabinet width is required, so a total cabinet opening width of 54" (137.16 cm) is recommended.

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

TOOLS NEEDED:

• Flat-blade screwdriver • 1/4" nut driver

• 7/16" and 1/2" open-end or • 1/4" drill bit two adjustable wrenches

NOTE: Your refrigerator dealer has a kit available with a 1/4" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or _6" (4.76 mm) saddle valve which reduces water flow and clogs more easily.

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

• Cordless drill

Water Pressure

A cold water supply with water pressure of between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice

maker. If you have questions about your water pressure, call a licensed, qualified plumber.

• If your refrigerator has a water dispenser: After installation is complete, use the water dispenser to check the water pressure.

• With the water filter removed, dispense 1 cup (237 mL) of water. If

1 cup of water is dispensed in 8 seconds or less, the water pressure to the refrigerator meets the minimum requirement.

• If it takes longer than 8 seconds to dispense 1 cup of water, the

water pressure to the refrigerator is lower than recommended. See "Problem Solver" for suggestions.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to

be between 30 and 120 psi (207 and 827 kPa). If a reverse osmosis water filtration system is connected to your cold water

supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system.

Remove the water filter. See '"Water Filtration System" in the User Instructions, User Guide, or Use & Care Guide.

If you have questions about your water pressure, call a licensed, qualified plumber.

Read all directions before you begin. IMPORTANT:

• Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and ordinances.

The gray water tubing on the back of the refrigerator (which is used to connect to the household water line) is a PEX (cross-linked polyethylene) tube. Copper and PEX tubing connections from the household water line to the refrigerator are acceptable, and will help avoid off-taste or odor in your ice or water. Check for leaks.

• Install tubing only in areas where temperatures will remain above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

• Flat-blade screwdriver

• 7/16" and 1/2" open-end wrenches or two adjustable wrenches

• 1/4" nut driver

Connect to Water Line

IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.

Style 1 (Recommended)

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

Use a quarter-turn shutoff valve or the equivalent, served by a 1/2" copper household supply line.

NOTE: To allow sufficient water flow to the refrigerator, a minimum 1/2" size copper household supply line is recommended.

iii

A B

A. Bulb

B, Nut

Now you are ready to connect the copper tubing to the shutoff valve. Use 1/4" (6.35 mm) O.D. (outside diameter) soft copper tubing to

connect the shutoff valve and the refrigerator.

• Ensure that you have the proper length needed for the job. Be sure both ends of the copper tubing are cut square.

• Slip compression sleeve and compression nut onto copper tubing

as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable

wrench. Do not overtighten.

C. Copper tubing [to refrigerator]

D, Household supply line [_ "minimum]

A. Compression sleeve

B. Compression nut

Place the free end of the tubing into a container or sink, and turn on main water supply to flush out tubing until water is clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final connection to the inlet of the water valve to avoid possible water valve

malfunction.

Bend the copper tubing to meet the water line inlet, which is located on the back of the refrigerator cabinet as shown. Leave a coil of copper tubing to allow the refrigerator to be pulled out of the cabinet or away from the wall for service.

Style 2

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a 1/2" (1.27 cm) to 11/4" (3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the pipe, not

the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

Determine the length of copper tubing you need. Measure from the connection on the lower rear corner of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing

are cut square.

C. Copper tubing

Using a cordless drill, drill a 1/4" (6.35 mm) hole in the cold water pipe you have selected.

6. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

G_J A

A. Co/el water pipe E. Compression sleeve

B. Pipe clamp E Shutoff valve

C. Copper tubing G. Packing nut

D. Compression nut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp.

Be sure the outlet end is solidly in the 1/4" (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the

packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not overtighten, or you may crush

the copper tubing.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as

far as it will go. Screw the compression nut onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF

the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

Style I

1. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the end of the water line inlet.

Thread the nut onto the end of the tubing. Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not touch the cabinet's side wall or other parts inside the cabinet.

_.......................B

A. Tube clamp D. Compression nut

& Tube clamp screw E. Valve in/et

G Copper tubing

On some models, the ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the 1/4" (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long enough, a 1/4" x 1/4" (6.35 mm x 6.35 mm) coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

A B C D E F G

A. Refrigerator water tubing E. Ferru/e [purchased]

B. Nut [provided] E Nut [purchased]

C. Bulb G. Household water line

D. Coupling [purchased]

A B

A. Househo/d water/ine

& Nut [purchased]

Install the water supply tube clamp around the water supply line to

c D

C. Ferru/e [purchased]

D. Refrigerator water tubing

reduce strain on the coupling.

Turn shutoff valve ON.

Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

Style 2

Unplug refrigerator or disconnect power.

Remove and discard the plastic part that is attached to the inlet of the water valve.

Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten.

Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help avoid damage to the tubing when the refrigerator is pushed back against the wall.

5. Turn shutoff valve ON.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Prepare the Water System" or "Water and Ice Dispensers."

NOTE: Allow 24 hours to produce the first batch of ice. Allow 72 hours to completely fill ice container.

Open the freezer door and turn on the ice maker. Move the switch to the ON (left) position. Please refer to the "Ice Maker and Storage Bin" section for further instructions on the operation of your ice maker.

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced.

• Depending on your model, you may want to select the maximum ice feature to increase the production of ice.

(on som<_modds}

On some models, your refrigerator's accessory packet includes two air filters, which must be installed prior to use. On some models, the air filters are already installed at the factory.

The air filter reduces the buildup of odors. This helps to maintain a cleaner environment inside the refrigerator.

Please read before using the water system. Immediately after installation, follow the steps below to make sure that the

water system is properly cleaned.

1. Open the freezer door and turn off the ice maker. The On/Off switch can only be accessed when the ice storage bin has been removed. The switch is located on the freezer door, on the left side of the wall that surrounds the ice storage bin. Move the switch to the OFF (right) setting.

2. Make sure the water filter is properly installed.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Flush the water system. Use a sturdy container to depress and hold the water dispenser lever for 5 seconds, then release it for 5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser lever (5 seconds on, 5 seconds off) until a total of 3 gal. (12 L) has been dispensed. This will flush air from the filter and water dispensing system, and prepare the water filter for use. Additional flushing may be required in some households. As air is cleared from the system, water may spurt out of the dispenser.

Installing the Air Filters (on some models)

The filters should be installed in two separate locations.

Location 1:

Install one of the filters behind the vented door, which is located (depending on your model) along either the rear or left interior wall near the top of the refrigerator compartment.

Remove the air filter from its packaging.

Lift open the vented door.

Snap the filter into place.

4. Close the vented door.

Location 2: Install the other filter in the filter housing assembly_ which is located along

an interior side wall of the crisper and/or convertible drawer.

3. Lift open the vented air filter door. There are notches behind the door. Slide the indicator down into the notches, facing outward.

NOTE: The indicator will not easily slide into the notches if the rear bubble has not been popped.

4. Close the air filter door, and check that the indicator is visible through the rectangular hole in the door.

Location 2:

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator until the bubble pops to activate the indicator.

3. Slide open the cap on the housing assembly.

4. Place the indicator in the top of the housing, facing outward.

5. Slide the cap closed, and check that the indicator is visible through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator's rear bubble has not been popped.

NOTE: There are two housing assemblies. Use one for one of the CleanFIow TM Air Filters, and use the other for the Crisperl<eeper TM Produce Preserver pouches. Do not install Air Filters and Produce Preserver pouches in the same housing assembly. See "Install Crisperl<eeper TM Produce

Preserver" for additional information.

1. Remove the air filter from its packaging.

2. Lift up on the housing in order to remove it from its mounting tab along the wall.

3. Snap the filter into place on the rear of the housing.

4. Place the housing back on the mounting tab along the wall.

Installing the Filter Status Indicators (on some models)

Each filter comes with a status indicator_ which should be activated and installed at the same time the air filter is installed.

Location 1:

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator, until the bubble pops to activate the indicator.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months, when the status indicator has completely changed from white to red.

To order a replacement air filter, see "Accessories."

1. Remove the old air filter by squeezing in on the side tabs.

2. Remove the old status indicator.

3. Install the new air filter and status indicator using the instructions in the previous sections.

_'__ _:_'}_s/_'{%;__:_,}_,__s,, li_'_OC__;t?ye _,_,__st_;s_}/y_,__ _,

On some models, your refrigerator's accessory packet includes a Produce Preserver, which should be installed prior to use. On some models, the Produce Preserver is already installed at the factory.

The Produce Preserver absorbs ethylene, allowing the ripening process of many produce items to slow down. As a result, certain produce items will stay fresh longer.

Ethylene production and sensitivity varies depending on the type of fruit or vegetable. To preserve freshness, it is best to separate produce with sensitivity to ethylene from fruits that produce moderate to high amounts of ethylene.

Apples

Asparagus

Berries

Broccoli

Cantaloupe

Carrots

Citrus Fruit

Grapes

Lettuce

Pears

Spinach

Sensitivity to

Ethylene

High

Med.

Low

High

Med.

Low

Med.

Low

High

Ethylene

Production

Very High

Very Low

Low

Very Low

High

Very Low

Very High

Very Low

Installing the Produce Preserver (on some models) Installing the Status Indicator (on some models)

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia, bleach or acids. Do not get in eyes, on skin or clothing. Do not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium permanganate. If swallowed, call a Poison Control Center or doctor immediately. Do not induce vomiting. If in eyes, rinse

with water for 15 minutes. If on skin, rinse with water.

For best performance_ always use two Produce Preserver pouches. Both pouches should be installed in the same housing assembly° which is located

along an interior side wall of the crisper and/or convertible drawer. NOTE: There are two housing assemblies. Use one for the CrisperKeeper TM

Produce Preserver pouches, and use the other for one of the CleanFIow TM Air Filters. Do not install Produce Preserver pouches and Air Filters in the same housing assembly. See "Install CleanFIow TM Air Filters" for additional

information.

The Produce Preserver comes with a status indicator_ which should be activated and installed at the same time the pouch is installed.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator, until the bubble pops to activate the indicator.

3. Slide open the cap on the Produce Preserver housing.

4. Place the indicator in the top of the housing, facing outward.

5. Slide the cap closed, and check that the indicator is visible through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator's rear bubble has not been popped.

Replacing the Produce Preserver (on some models)

The disposable pouches should be replaced every 6 months, when the status indicator has completely changed from white to red.

To order replacements, see "Accessories."

1. Remove the old pouches from the Produce Preserver housing.

2. Remove the old status indicator.

3. Install the new pouches and status indicator using the instructions in the previous sections.

1. Remove the Produce Preserver pouches from their packaging.

2. Lift up on the housing in order to remove it from its mounting tab along the wall.

3. Open the housing by pulling up and out on the back of the top of the housing.

4. Place both pouches inside the housing, then snap the housing back together.

5. Place the housing back on the mounting tab along the wall.

REFRIGERATOR USE

Air circulates through vents within each compartment, and does not transfer between the compartments.

Single Evaporator (on some models)

In order to ensure proper temperatures, you need to permit air to flow between the two sections. Cold air enters the bottom of the freezer section

and moves up. It then enters the refrigerator section through the top vent. (On Style 2 models, this air is also evenly distributed throughout the refrigerator compartment through six vents on the back wall.) Air then

returns to the freezer as shown.

Style I Style 2

Do not block any of these vents with food such as soda, cereal, bread, etc. If the vents are blocked, airflow will be obstructed and temperature and moisture problems may occur.

IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To avoid odor transfer and drying out of food, wrap or cover foods tightly.

.............................. ill•

_ " I _

=_=_= CIIIIIIIIIIIIIIIIIIIIIIIIIII;IIIIII;:t::::i

Do not block any of these vents with food such as soda, cereal, bread, etc. If the vents are blocked, airflow will be obstructed and temperature and

moisture problems may occur. NOTE: The dual evaporation system is always activated when your

refrigerator is operating. You do not need to press any buttons to turn it on.

The refrigerator and freezer controls are located on the dispenser panel. IMPORTANT: The display screen on the dispenser control panel will turn off

automatically and enter "sleep" mode when the control buttons and dispenser pad have not been used for 2 minutes or more. While in "sleep" mode, the first press of a control button will only reactivate the display screen, without changing any settings.

• Touch any control button on the dispenser panel to activate the display screen. The home screen will appear as shown.

Dual Evaporator (on some models)

Some models come equipped with a dual sequential evaporation system, which includes two separate evaporators for the refrigerator and freezer compartments.

Dual evaporation results in higher humidity, which helps keep foods in the refrigerator from spoiling as quickly and improves food quality and freshness in the freezer due to decreased freezer burn. In addition, the dual evaporation system helps keep food smells in the refrigerator from transferring to ice in the freezer.

AdjustingtheControls

For your convenience, your refrigerator and freezer controls are preset at the factory. When you first install your refrigerator, make sure that the

controls are still set to the "mid-settings." The factory recommended set points are 37°F (3°C) for the refrigerator and 0°F (-18°C) for the freezer.

IMPORTANT:

• Wait 24 hours before you put food into the refrigerator. If you add food before the refrigerator has cooled completely, your food may

spoil.

NOTE: Adjusting the set points to a colder than recommended setting will not cool the compartments any faster.

If the temperature is too warm or too cold in the refrigerator or freezer° first check the air vents to be sure they are not blocked before

adjusting the controls.

The preset settings should be correct for normal household usage. The controls are set correctly when milk or juice is as cold as you like and

when ice cream is firm.

• Wait at least 24 hours between adjustments. Recheck the temperatures before other adjustments are made.

To view and adjust the set points, press and hold the TEMPERATURE button for 3 seconds. When adjust mode is activated, adjusting information will appear on the display screen.

When adjusting temperature set points, use the following chart as a guide.

CONDITION: TEMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR Setting

1° higher

REFRIGERATOR too warm REFRIGERATOR Setting

1° lower

FREEZER too cold FREEZER Setting

1° higher

FREEZER too warm / FREEZER Setting Too little ice 1° lower

The set point range for the refrigerator is 33°F to 42°F (O°C to 6°C). The set point range for the freezer is -9°F to 5°F (-23°C to -15°C).

Cooling On/Off

Your refrigerator and freezer will not cool when cooling is turned off.

• To turn cooling off, press and hold the LOCI( and MEASURED FILL buttons at the same time for 3 seconds.

IMPORTANT: To avoid unintentionally locking the dispenser or changing other settings, be sure to press both buttons at exactly the

same time.

When cooling is off, "COOLING OFF" will appear on the display screen.

• Press and hold LOCI( and MEASURED FILL for 3 seconds again to turn cooling back on.

NOTE: To view Celsius temperatures, press the MEASURED FILL button when adjust mode is activated. To return the display setting to Fahrenheit, press MEASURED FILL again.

• When adjust mode is activated, the display screen shows the refrigerator set point and "REFRIGERATOR" appears.

• Press SETTINGS to raise the set point, or press TEMPERATURE to lower the set point.

When you have finished viewing (and adjusting if desired) the refrigerator set point, press ACCENT LIGHT to change the display to show the freezer set point. When the zone has been changed, "FREEZER" appears on the display screen.

• Press SETTINGS to raise the set point, or press TEMPERATURE to lower the set point.

When you have finished viewing (and adjusting if desired) both the refrigerator and freezer set points, press LOCI( to save the settings.

NOTE: To exit without saving changes, press WATER/ICE at any time while in adjust mode, or allow about 60 seconds of inactivity and adjust mode will turn off automatically.

Additional Features

Accelerated Ice Production

The Accelerated Ice feature assists with temporary periods of heavy ice usage by increasing ice production.

IMPORTANT: This feature only works if the ice maker is turned on. See "ice Maker and Storage Bin."

• To turn on the feature° press SETTINGS then TEMPERATURE. When the feature is on, the Accelerated Ice icon will appear on the dispenser display screen.

_ z_ Accela

- _ ke

The Accelerated Ice setting will remain on for a minimum of 90 minutes unless manually turned off.

• To manually turn off the feature, press SETTINGS then TEMPERATURE again, or adjust the freezer temperature set point. The Accelerated Ice icon will disappear when the feature is off.

NOTE: If increased ice production is desired at all times, change the freezer set point to a lower setting. Setting the freezer to a colder temperature may make some foods, such as ice cream, harder.

Door Ajar Alarm The Door Ajar Alarm feature sounds an alarm when the refrigerator or

freezer door is open for 5 minutes and the product cooling is turned on. The alarm will repeat every 2 minutes. Close both doors to turn it off. The feature then resets and will reactivate when either door is left open again

for 5 minutes. NOTE: To mute the audible alarm while keeping the doors open, such as

while cleaning the inside of the refrigerator, press any button on the control panel. The alarm sound will be temporarily turned off, but the Door Ajar icon will still be displayed on the dispenser control panel.

Disabling Sounds

• To turn off all dispenser and control sounds, press and hold WATER/ ICE and MEASURED FILL at the same time for 3 seconds.

IMPORTANT: To avoid unintentionally changing other settings, be sure to press both buttons at exactly the same time.

To turn all sounds back on, press and hold WATER/ICE and MEASURED FILL at the same time for 3 seconds again.

NOTES:

• The dispensing system will not operate when either door (refrigerator or freezer) is open.

• Allow 24 hours for the refrigerator to cool down and chill water.

• Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Wait 72 hours for full ice production.

The display screen on the dispenser control panel will turn off automatically and enter "sleep" mode when the control buttons and dispenser pad have not been used for 2 minutes or more. While in "sleep" mode, the first press of a control button will only reactivate the display screen, without changing any settings.

Flush the Water System

Press and hold the SETTINGS and LOCI( buttons at the same time for 3 seconds. The words "Back" and "1 Cup" will appear on the display

screen. Also, "CALIBRATION" will illuminate and remain lit while the Measured Fill feature is being calibrated.

NOTE: You may press the WATER/ICE button under the word "Back" at any time to exit calibration mode. The display screen's

"CALIBRATION" text will turn off.

Using your hand (not the measuring cup), press and release the water dispenser pad in order to dispense water to the 1 cup fill line.

Air in the water dispensing system can cause the water dispenser to drip. After connecting the refrigerator to a water source or replacing the water filter, flush the water system. Flushing the water dispensing system forces air from the water line and filter, and prepares the water filter for use.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

1. Using a sturdy container, depress and hold the water dispenser pad for 5 seconds, then release it for 5 seconds.

2. Repeat Step 1 until water begins to flow.

3. Once water begins to flow, continue depressing and releasing the dispenser pad (5 seconds on, 5 seconds off) until a total of 3 gal. (12 L) has been dispensed.

Additional flushing may be required in some households.

Dispensing Options

Your dispenser can dispense water and ice in two ways.

• The DISPENSE WATER button, located below the dispenser control panel's display screen, dispenses only water.

• The dispenser pad is the pad located along the rear wall of the dispenser cavity. When pressed, it dispenses either water or ice,

depending on the chosen setting.

To dispense both water and ice at the same time, select the desired type of ice and dispense it using the dispenser pad, then press the DISPENSE

WATER button while still dispensing ice.

Calibrate Measured Fill

Household water pressure may affect the accuracy of the Measured Fill feature. For optimum performance of your water dispenser, you must first

calibrate Measured Fill.

IMPORTANT: Flush the water system before calibrating Measured Fill.

1. Place a sturdy measuring cup (1 cup [237 mL] size) on the dispenser tray, centered in front of the water dispenser pad.

NOTE: Depending on your model, a measuring cup may be provided.

NOTE: If overfilling or spilling occurs, discard the water and press "Back" to restart the calibration process.

4. When 1 cup of water has been correctly dispensed into the measuring cup, press the MEASURED FILL button under the word "Confirm" to

confirm the calibration.

When Measured Fill calibration has been confirmed, the display will return to the home screen.

The Water Dispenser

IMPORTANT:

Dispense at least 1 qt (1 L) of water every week to maintain a fresh supply.

If the flow of water from the dispenser decreases, it could be caused by low water pressure.

• With the water filter removed, dispense 1 cup (237 mL) of water. If

1 cup of water is dispensed in 8 seconds or less, the water pressure to the refrigerator meets the minimum requirement.

• If it takes longer than 8 seconds to dispense 1 cup of water, the

water pressure to the refrigerator is lower than recommended. See "Water Supply Requirements" or "Problem Solver" for suggestions.

To Dispense Water (Standard): NOTE: While dispensing water and for 3 seconds after dispensing has

stopped, the digital display will show how much water has been dispensed. The default unit is ounces. To switch to cups or liters, press the SETTINGS button, then press MEASURED FILL to toggle through the available units.

Option I:

1. Place a sturdy glass below the dispenser opening.

2. To dispense water, press the DISPENSE WATER button. Hold the glass close to the water dispenser spout to ensure that the water dispenses into the glass.

A. Water dispenser spout

3. To stop dispensing, press the DISPENSE WATER button a second time.

Option 2:

1. Press the WATER/ICE button until "Water" is selected.

2. Press a sturdy glass against the dispenser pad. Hold the glass close to the water dispenser spout to ensure that the water dispenses into the glass.

IMPORTANT: Low water pressure may affect the accuracy of this feature.

1. Press MEASURED FILL to turn the feature on. When the feature is on, the Measured Fill screen appears on the display.

Press WATER/ICE to manually turn off the Measured Fill feature.

NOTE: The dispenser will automatically turn off Measured Fill after 1 minute of inactivity. When Measured Fill is turned off, any changes you

have made will be lost and all defaults will be restored.

You can dispense water by the ounce, cup, or liter. The default unit is ounces. To switch to cups or liters while the Measured Fill feature is already on, press the MEASURED FILL button to toggle through the

available units. Default, minimum, and maximum volumes are listed below.

Units Default Minimum Maximum

Ounces 8 1 128

Cups 1 1/4 16 Liters 0.25 0.05 4.00

A. Water dispenser spout

3. Remove the glass to stop dispensing.

To Dispense Water (Measured Fill): Measured Fill allows you to dispense a specified amount of water with the

touch of a few buttons. NOTE: The amount of water you select will be dispensed. Be sure that the

container is empty and can hold the entire volume. If ice is in the container, you may need to adjust your selection.

Press the SETTINGS and TEMPERATURE buttons to adjust the volume as desired. The SETTINGS button increases the volume, and the

TEMPERATURE button lowers the volume. NOTES:

• When increasing or decreasing the volume of water, the control

may stop responding if an adjustment button is held for approximately 10 seconds or longer. Release the button for approximately 2 seconds, then continue making adjustments.

• Most coffee cups (commonly 4 to 6 oz [118 to 177 mL] per cup)

are not the same size as a measuring cup (8 oz [237 mL]). You may need to adjust the volume to avoid unintentionally overfilling coffee cups.

You can save one "favorite" volume for repeated use. Adjust the settings until the desired volume is displayed, then press LOCI< to save the volume. In future Measured Fill use, press LOCI< to access the saved volume setting.

NOTE: You can only save one "favorite." Saving a new volume will overwrite the previously-saved "favorite."

To dispense water, press a sturdy glass against the dispenser pad OR place the glass below the dispenser opening and press either the

DISPENSE WATER button or the ACCENT LIGHT button. Hold the glass close to the water dispenser spout to ensure that the water

dispenses into the glass.

A. Water dispenser spout

NOTE: While dispensing water, the digital display will count down how much water remains to be dispensed, according to the volume you selected. The flow of water will automatically stop once the desired volume has been dispensed.

To stop dispensing before the selected volume has been dispensed, remove the glass from the dispenser pad OR press either the

DISPENSE WATER button or the ACCENT LIGHT button a second time.

NOTE: If you stop dispensing before the desired volume has been dispensed, the digital display will continue to show how much water remains to be dispensed. The display will turn off after 1 minute of inactivity.

The Ice Dispenser

Ice dispenses from the ice maker storage bin in the freezer when the dispenser pad is pressed. To turn off the ice maker, see "ice Maker and Storage Bin."

Your ice maker can produce both crushed and cubed ice. Before dispensing ice, select which type of ice you prefer by pressing the WATER/ICE button.

The display screen indicates which type of ice is selected.

To Dispense Ice:

1. Make sure the desired type of ice is selected. To switch between cubed and crushed, press WATER/ICE.

Cut Hazard

Use a sturdy glass when dispensing ice. Failure to do so can result in cuts.

2. Press a sturdy glass against the dispenser pad. Hold the glass close to the ice guide to ensure that the ice dispenses into the glass.

A. Ice guide

IMPORTANT: You do not need to apply a lot of pressure to the pad in order to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.

NOTE: To dispense both water and ice at the same time, press the DISPENSE WATER button while using the dispenser pad to dispense

ice.

Remove the glass to stop dispensing. NOTE: Ice may continue to dispense for several seconds after

removing the glass from the pad. The dispenser may continue to make noise for a few seconds after dispensing.

CRUSHED CUBED

For crushed ice, cubes are crushed before being dispensed. This may cause a slight delay when dispensing crushed ice. Noise from the ice crusher is normal, and pieces of ice may vary in size. When changing from crushed to cubed, a few ounces of crushed ice will be dispensed along with the first

cubes.

TheDispenserLight

The dispenser has two separate lights: a white dispenser light and a blue dispenser pad light.

The white dispenser light automatically turns on when you use the dispenser, then turns off when dispensing stops.

The blue dispenser pad light can be manually turned on or off.

• Press the ACCENT LIGHT button to turn the dispenser pad light on. The display screen indicates when the light is on.

Press ACCENT LIGHT a second time to turn the dispenser pad light off.

If the dispenser lights do not appear to be working as described in "Water and Ice Dispensers" (in the User Instructions, User Guide, or Use & Care Guide) or if the interior lights do not illuminate when either door is opened, call for assistance or service. See either the back cover or the Warranty for contact information.

The Dispenser Lock

The dispenser can be turned off for easy cleaning or to avoid unintentional

dispensing by small children and pets. NOTE: The lock feature does not shut off power to the refrigerator, to the

ice maker, or to the dispenser light. It simply deactivates the controls and dispenser pad. To turn off the ice maker, see "Ice Maker and Storage Bin."

• Press and hold LOCI( for 3 seconds to lock the dispenser.

• Press and hold LOCI( a second time to unlock the dispenser.

The display screen indicates when the dispenser is locked.

Press SETTINGS, then press SETTINGS again. The display screen will show how many more gallons of water the filter can effectively filter. Press WATER/ICE to exit the filter status screen.

NOTE: A new filter's "Gallons Remaining" display is 200. The

"ORDER" status begins at 40 gal. (151 L) remaining, and the "REPLACE" status activates when the filter has 0 gal. remaining.

Resetting the Filter Status

• After changing the water filter, reset the status light. Press and hold TEMPERATURE and SETTINGS at the same time for 3 seconds.

IMPORTANT: To avoid unintentionally changing other settings, be sure to press both buttons at exactly the same time.

When the system is reset, the "ORDER" and "REPLACE" icons will disappear from the display screen.

NOTE: When the status displays "REPLACE," you can temporarily reset the status icon manually, without changing the water filter. Press and hold the

ACCENT LIGHT and TEMPERATURE buttons at the same time for 3 seconds. The "REPLACE" display will be turned off for 14 days. When it

turns back on, you can manually reset it again if desired.

Changing the Water Filter

1. Locate the water filter in the top-right corner of the refrigerator compartment.

2. Lift open the filter cover door. The filter will be released and then be ejected as the door is opened.

3. When the door is completely open, pull the filter straight out. NOTE: There may be some water in the filter. Some spilling may occur.

Use a towel to wipe up any spills.

4. Take the new filter out of its packaging and remove the cap. Be sure the O-rings are still in place after the cap is removed.

Water Filter Status Light

The water filter status light will help you know when to change your water

filter.

• When the dispenser control panel's water filter status display changes to "ORDER," this tells you that it is almost time to change the water filter cartridge.

• Replace the water filter cartridge when the water filter status display changes to "REPLACE."

NOTE: If water flow to your water dispenser or ice maker decreases noticeably, change the filter sooner. The filter should be replaced at least every 6 months, depending on your water quality and usage.

You can check the remaining life of your water filter at any time.

[]

B. O-rings

5°

With the arrow pointing up, align the new filter with the filter housing and slide it into place. The filter cover door will automatically begin

to close as the new filter is inserted.

6. Close the filter cover door completely in order to snap the filter into place. You may need to press hard.

7. Flush the water system. See "Water and Ice Dispensers."

Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

Do not use anything sharp to break up the ice in the storage bin. This can cause damage to the ice container and the dispenser mechanism.

• Do not store anything on top of or in the ice maker or storage bin.

Turning the Ice Maker On/Off: The On/Off switch, located on the left wall of the freezer door, can only

be accessed when the ice storage bin has been removed. See the following section for bin removal instructions.

Removing and Replacing the Ice Storage Bin:

1. Press down the release lever and tilt the bucket outward. Use both hands to hold the base of the storage bin, then lift it up and out.

)

A. Release lever

NOTE: It is not necessary to flip the ice maker On/Off switch to the OFF (down) position when removing the storage bin. The storage bin sensor, located on the left wall of the freezer door, stops the ice maker from producing ice if the door is open or the storage bin is removed.

• To turn on the ice maker, flip the switch to the ON (up) position.

• To manually turn off the ice maker, flip the switch to the OFF (down) position.

NOTE: The ice maker has an automatic shutoff to keep the storage bin from overfilling during normal operation. As ice is made, the ice cubes will fill the ice storage bin, and the ice cubes will raise the shutoff arm to the OFF (arm up) position. When the storage bin is at full capacity, the ice maker will automatically stop ice production, but the ice maker On/Off switch will remain in the ON (up) position.

ii:iililif!illii ilill

Ice production OFF

(Shutoff arm UP)

Ice production ON

(Shutoff arm DO WN)

A. On/Off switch

B. Storage bin sensor

2. Replace the bin by sliding it onto the door, then tilting it back into an upright position. The release lever will click when the bin is securely in place.

REFRIGERATORFEATURES

Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word "Accessory." Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please call the toll-free number on the

back cover or in the "Accessories" section.

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Ref_ ge_x_ e Dee _'BN_s

To Remove and Replace the Bins:

1. Remove the bin by lifting it and pulling it straight out.

2. Replace the bin by sliding it in above the desired supports and pushing it down until it stops.

_ef_- ge_x;s@: She yes

_'_u_s_sbe of s}_se yes vas' es L_pymode}

Store similar foods together and adjust the shelves to fit different heights. This reduces the time the refrigerator door is open and saves energy.

To Remove and Replace a Shelf:

1. Pull the shelf forward to the stop. Tilt the front of the shelf up and lift it slightly as you pull the shelf from the frame.

2. Replace the shelf by guiding it back into the slots on the frame and pushing the shelf in past the stop.

W_e Rc_ck

on so_'s® rsede s

The wine rack can be placed on any set of refrigerator shelf supports, either with (as shown below) or without a shelf on the same supports.

e> se_s_÷modes

To Remove and Replace the Bottle/Can Rack:

1. Remove the bottle/can rack by lifting it and pulling it straight out.

2. Replace the bottle/can rack by sliding it in above the desired supports and pushing it down until it stops.

NOTE: If the wine rack is sharing a set of supports with a shelf, you must first remove the shelf in order to remove the wine rack.

(o_'_some modes}

The deli drawer stores raisins, nuts, spreads, and other small items at normal refrigerator temperatures.

To Remove and Replace the Deli Drawer:

1. Remove the dell drawer by sliding it straight out to the stop. Lift the front and slide the drawer out the rest of the way.

2. Replace the dell drawer by sliding it back past the stop.

Crisper and Convertible Vegetable/Meat Drawers

To Remove and Replace Drawers:

1. Slide crisper or meat drawer straight out to the stop. Lift the front of drawer with one hand while supporting the bottom of drawer with the other hand and slide the drawer out the rest of the way.

2. Replace the crisper or meat drawer by sliding it back in fully past the drawer stop.

Crisper and Convertible Vegetable/Meat Drawer Covers

To Remove and Replace Covers:

1. Remove the crisper and meat drawer. Press up in center of crisper

glass insert until it rises above the plastic frame. Holding the crisper glass firmly, slowly slide the glass insert forward to remove. Lift crisper cover frame and remove. Repeat steps to remove the meat drawer cover,

Replace back of meat drawer cover frame into supports or slides on side walls of the refrigerator and lower or slide the front of the cover frame into place. Slide rear of glass insert into cover frame and lower front into place. Repeat steps to replace the crisper cover.

on so_s,_emodels}

The convertible vegetable/meat drawer can be adjusted to properly chill meats or vegetables. The air inside the pan is cooled to avoid "spot" freezing and can be set to keep meats at the National Livestock and Meat Board recommended storage temperatures of 28 ° to 32°F (-2 ° to O°C).

IMPORTANT: To extend freshness, wrap meats in airtight, moisture-proof materials before storing. Always store meat as recommended.

Adjusting the Control:

• Move the control to the right (less cold) or to the left (colder) as

desired.

Meat Vegetables

I I I I I

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and moisture- proof. Rewrap if necessary. See the following chart for storage times.

When storing meat longer than the times given, freeze the meat.

Fresh fish or shellfish ............................................ use same day as purchased

Chicken, ground beef, variety meat (liver, etc.) ................................. 1-2 days

Cold cuts, steaks/roasts ......................................................................... 3-5 days

Cured meats .......................................................................................... 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or plastic containers with tight lids.

Q' spe__HumdW Co_4_o

You can control the amount of humidity in the moisture-sealed crisper. Adjust the control to any setting between FRUIT [-] and VEGETABLES [+].

Fruit Vegetables

@1 I I I I©

Humidity Control

FRUIT [-] (open) lets moist air out of the crisper for best storage of fruits and vegetables with skins.

• Fruit: Wash, let dry and store in refrigerator in plastic bag or crisper. Do not wash or hull berries until they are ready to use. Sort and keep berries in original container in crisper, or store in a

loosely closed paper bag on a refrigerator shelf.

• Vegetables with skins: Place in plastic bag or plastic container and store in crisper.

VEGETABLES [+] (closed) keeps moist air in the crisper for best storage of fresh, leafy vegetables.

• Leafy vegetables: Wash in cold water, drain and trim or tear off

bruised and discolored areas. Place in plastic bag or plastic

container and store in crisper.

U¢_'V Bts

ot_ sots_e m®d®s ,,,Acc®sso y

The utility bin can be placed anywhere inside the refrigerator or freezer. It can be used to hold various small items such as kids' snacks, or for extra ice storage.

NOTE: For long-term storage, place eggs in a covered container or in their original carton on an interior shelf.

FREEZER FEATURES

Your model may have some or all of these features.

Temperature Control

To store vegetables: Set the control to VEGETABLES (all the way to the right) to store vegetables at their optimal storage temperatures (which need to be warmer than those for meat).

IMPORTANT: If food starts to freeze, move the control to the right (less cold), toward the VEGETABLES setting. Remember to wait 24 hours between adjustments. Doing so gives the temperature of the food time to change.

Frozen Food Storage Guide

Storage times will vary according to the quality and type of food, the type of packaging or wrap used (should be airtight and moisture-proof), and the storage temperature. Ice crystals inside a sealed package are normal. This simply means that moisture in the food and air inside the package have condensed, creating ice crystals.

Put no more unfrozen food into the freezer than will freeze within 24 hours (no more than 2 to 3 Ibs of food per cubic foot [907 to 1,350 g per 28 L] of

freezer space). Leave enough space in the freezer for air to circulate around packages. Be certain to leave enough room for the door to close tightly.

For more information on preparing food for freezing, check a freezer guide or reliable cookbook.

To Remove and Replace the Bins:

1. Remove the bin by lifting it and pulling it straight out.

2. Replace the bin by sliding it in above the desired supports and pushing it down until it stops.

(r_u_'_be ot_she yes v¢_'_esby rs_,de }

To Remove and Replace a Shelf:

1. Pull the shelf forward to the stop. Tilt the front of the shelf up and lift it slightly as you pull the shelf from the frame.

2. Replace the shelf by guiding it back into the slots on the frame and pushing the shelf in past the stop.

0_ so_se s's_odes

The freezer bin can be used to store bags of frozen fruits and vegetables that may slide off freezer shelves.

To Remove and Replace the Freezer Bin:

1. Remove the bin by sliding it out to the stop. Lift the front to slide the bin out the rest of the way.

2. Replace the bin by positioning it on the rails. Lift the bin front slightly while pushing it in fully past the stops.

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However° clean both compartments about once a month to avoid buildup of odors. Wipe up spills immediately.

To Clean Your Refrigerator:

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves, crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in

warm water.

• Do not use abrasive or harsh cleaners such as window sprays,

scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools. These can scratch or damage materials.

• To help remove odors, you can wash interior walls with a mixture

of warm water and baking soda (2 tbs to 1 qt [26 g to 0.95 L] of water).

Determine whether your refrigerator exterior is painted metal, Ultra Satin TM (stainless look) finish, brushed aluminum or stainless steel, and choose the appropriate cleaning method.

NOTE: Ultra Satin TM (stainless look) finish has a smooth, uniform color with a glossy finish that resists fingerprints. Stainless steel has a distinct grainy texture with variation in color that is natural to steel.

Painted metal: Wash exteriors with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth. Additionally, to avoid damage to painted metal exteriors, apply appliance wax (or auto paste wax) with a clean, soft cloth. Do not wax plastic parts.

Brushed aluminum: Wash with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth.

Ultra Satin TM (stainless look) finish: Wash with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners or cleaners designed for stainless steel. Dry thoroughly

with a soft cloth.

Stainless steel finish: Wash with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners. Dry thoroughly with a soft cloth.

• To keep your stainless steel refrigerator looking like new and to

remove minor scuffs or marks, it is suggested that you use the manufacturer's approved Stainless Steel Cleaner and Polish. To order the cleaner, see "Accessories."

IMPORTANT: This cleaner is for stainless steel parts only!

• Do not allow the Stainless Steel Cleaner and Polish to come into contact with any plastic parts such as the trim pieces, dispenser

covers or door gaskets. If unintentional contact does occur, clean plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft cloth.

If your model has a touch screen display on the dispenser panel, clean the screen using a soft, lint-free cloth. Mix a mild detergent with water, then use the mixture to dampen the cloth and gently wipe the screen.

• To avoid unintentionally changing settings, make sure the refrigerator is unplugged or the power is disconnected before wiping the screen.

• Do not over-saturate the cloth. Do not spray or wipe liquids directly onto the screen. Do not use abrasive or harsh cleaners

such as window sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, nail polish remover,

bleaches or cleansers containing petroleum products. Do not use paper towels, scouring pads, or other harsh cleaning tools. These

can scratch or damage materials.

There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or

dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille. See "Base Grille" graphic or "Base Grille" section.

• Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

IMPORTANT: The refrigerator and freezer compartments, air tower and dispenser lights are LEDs that cannot be changed by yourself. To order replacement LED lightings, please, call Whirlpool service (1-800-253-1301 (U.S.A.) or 1-800-807-6777 (Canada).)

If the power will be out for 24 hours or less, keep the door or doors closed (depending on your model) to help food stay cold and frozen.

If the power will be out for more than 24 hours, do one of the following:

• Remove all frozen food and store it in a frozen food locker.

• Place 2 Ibs (907 g) of dry ice in the freezer for every cubic foot (28 L) of freezer space. This will keep the food frozen for 2 to 4 days.

• If neither a food locker nor dry ice is available, consume or can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled one. A freezer full of meat stays cold longer than a freezer full of baked goods. If you see that food contains ice crystals, it may be refrozen, although the quality and flavor may be affected. If the condition of the food is poor, dispose of it.

3. If you have an automatic ice maker, turn off the ice maker. NOTE: Depending on your model, raise the wire shutoff arm to OFF

(up) position or press the switch to OFF.

4. Empty the ice bin.

If You Choose to Turn Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day ahead

of time.

• When the last load of ice drops, raise the wire shutoff arm to the

OFF (up) position or move the switch to the OFF setting.

3. Depending on the model, turn the Refrigerator Control to OFF or turn cooling off. See "Using the Controls" in the User Instructions, User

Guide, or Use & Care Guide.

4. Clean, wipe, and dry thoroughly.

5. Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and mold from

building up.

Moving

When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day ahead

of time.

• Disconnect the water line from the back of the refrigerator.

• When the last load of ice drops, raise the wire shutoff arm to the

OFF (up) position or move the switch to the OFF setting.

Remove all food from the refrigerator and pack all frozen food in dry

ice.

3. Empty the ice bin.

4. Depending on the model, turn the Refrigerator Control to OFF or turn cooling off. See "Using the Controls" in the User Instructions, User

Guide, or Use & Care Guide.

5. Unplug refrigerator.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them together so they don't shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator so it rolls more easily or screw in the leveling legs so they don't scrape the floor.

See "Adjust the Doors" or "Door Removal, Leveling and Alignment."

9. Tape the doors closed and tape the power cord to the back of the refrigerator.

When you get to your new home, put everything back and refer to the Installation Instructions for preparation instructions. Also, if your refrigerator has an automatic ice maker, remember to reconnect the water supply to the refrigerator.

Vacations

If You Choose to Leave Refrigerator On While You Are Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker and is connected to the household water supply, turn off the water supply to the refrigerator. Property damage can occur if the water supply is not

turned off.

PROBLEM SOLVER

First try the solutions suggested here or visit our website to possibly avoid the cost of a service call.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

GENERAL OPERATION Possible Causes and/or Recommended Solutions

Refrigerator will not operate • Not connected to an electrical supply - Plug the power cord into a grounded 3 prong outlet. Do not use an

Motor seems to run too much

Refrigerator seems noisy The compressor in your new refrigerator regulates temperature more efficiently and uses less energy than older

extension cord.

No power to the electrical outlet - Plug in a lamp to see if the outlet is working.

Household fuse has blown or circuit breaker has tripped - Replace the fuse or reset the circuit breaker. If the problem continues, contact a licensed electrician.

Control or cooling is not turned on - Turn on the refrigerator control, or turn cooling on. See "Using the Controls."

• New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool completely.

NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either compartment (refrigerator or freezer) more quickly.

Your new refrigerator has an energy-efficient motor - The refrigerator may run longer than you're used to, because the compressor and fans operate at lower speeds that are more energy-efficient. This is normal.

NOTE: Your refrigerator may run even longer if the room is warm, a large load of food is added, the doors are opened often, or if a door has been left open.

models. During various stages of operation, you may hear normal operating sounds that are unfamiliar.

The following noises are normal:

• Buzzing/Clicking - Heard when the water valve opens and closes to dispense water or fill the ice maker. If the refrigerator is connected to a water line, this is normal. If the refrigerator is not connected to a water line, turn

off the ice maker.

• Cracking/Crashing - Heard when ice is ejected from the ice maker mold.

• Popping - Heard when the inside walls contract/expand, especially during initial cooldown.

• Pulsating/Whirring - Heard when the fans/compressor adjust to optimize performance during normal operation.

• Rattling - Heard when water passes through the water line, or due to the flow of refrigerant. Rattling may also come from items placed on top of the refrigerator.

• Water running or gurgling - Heard when ice melts during the defrost cycle and water runs into the drain pan.

• Sizzling - Heard when water drips onto the heater during the defrost cycle.

GENERAL OPERATION Possible Causes and/or Recommended Solutions

Temperature is too warm • New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool completely.

NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either compartment (refrigerator or freezer) more quickly.

• Doors are opened often or not closed completely - This allows warm air to enter the refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors are properly sealed.

• Air vents are blocked - Remove items that are immediately in front of the vents.

• Large amount of warm food recently added - Allow several hours for the refrigerator to return to its normal temperature.

• Controls are not set correctly for the surrounding conditions - Adjust the controls to a colder setting. Check the temperature again in 24 hours.

Temperature is too cold Controls are not set correctly for the surrounding conditions - Adjust the controls to a warmer setting. Check the

Interior moisture buildup NOTE: Some moisture buildup is normal. Clean with a soft dry cloth.

Interior lights do not work • Doors have been open for an extended period of time - Close the doors to reset the lights.

Dispenser lights do not work

(on some models)

temperature again in 24 hours.

Top refrigerator shelf is colder than lower shelves - On some models, air from the freezer enters the refrigerator compartment through vents near the top refrigerator shelf. As a result, the top shelf can be slightly colder than

lower shelves.

• Air vents are blocked - Remove items that are immediately in front of the vents.

• Room is humid - A humid environment contributes to moisture buildup. Use the refrigerator only in an indoor location, with as little humidity as possible.

• Doors are opened often or not closed completely - This allows humid air to enter the refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors are properly sealed.

• Light bulb is loose in the socket or has burned out - On models with incandescent or full-size LED interior light bulbs, tighten or replace the bulb. See "Lights."

NOTE: On models with mini LED lights, call for assistance or service if the interior lights do not illuminate when

either door is opened. See either the front cover or the Warranty for contact information.

• Dispenser light is turned off - On some models, if the dispenser light is set to OFF, the light will turn on only when a dispenser pad/lever is pressed. If you want the dispenser light to stay on continuously, select a different

setting. See "Water and Ice Dispensers."

• Dispenser light is set to AUTO or NIGHT LIGHT - On some models, if the dispenser light is set to AUTO or NIGHT LIGHT, make sure the dispenser light sensor is not blocked. See "Water and Ice Dispensers."

NOTE: On models with mini LED lights, call for assistance or service if the dispenser lights do not operate correctly. See either the front cover or the Warranty for contact information.

Explosion Hazard

Use nonflammable cleaner. FaUure to do so can result in death, explosion, or fire.

DOORS AND LEVELING Possible Causes and/or Recommended Solutions

Doors are difficult to open • Gaskets are dirty or sticky - Clean the gaskets and contact surfaces with mild soap and warm water. Rinse and

dry with a soft cloth.

Doors will not close completely • Door is blocked open - Move food packages away from the door. Make sure all bins and shelves are in their

Doors appear to be uneven • Doors need to be aligned, or refrigerator needs to be leveled - See the leveling and door alignment instructions.

Refrigerator rocks • Refrigerator is not level - To stabilize the refrigerator, remove the base grille and lower the leveling feet until and is not stable they touch the floor. See the leveling and door alignment instructions.

correct positions. Make sure all packaging materials have been removed.

Cut Hazard

Use a sturdy glass when dispensing ice. Failure to do so can result in cuts.

ICE AND WATER

Ice maker is not producing ice,

not producing enough ice, or producing

small/hollow ice

Ice dispenser

will not operate properly

Possible Causes and/or Recommended Solutions

• Refrigerator is not connected to a water supply, or the water supply shutoff valve is not fully turned on - Connect the refrigerator to a water supply and make sure the water shutoff valve is fully open.

• Kink in the water source line - A kink in the water line can reduce water flow, resulting in decreased ice production, small ice cubes, and/or hollow or irregularly-shaped ice. Straighten the water line.

• Ice maker is not turned on - Turn on the ice maker. See "ice Maker and Storage Bin."

• New installation - After connecting the refrigerator to a water source, flush the water system. (See "Water and Ice Dispensers.") Wait 24 hours for ice production to begin. Wait 72 hours for full ice production. Discard the first three

batches of ice produced.

• Large amount of ice was recently removed - Allow sufficient time for the ice maker to produce more ice.

• Ice is jammed in the ice maker ejector arm (on some models) - Remove ice from the eiector arm using a plastic utensil.

• Inadequate water pressure - Verify that the household has adequate water pressure. See "Water Supply Requirements."

• Water filter is installed incorrectly - Make sure the filter is properly installed. See "Water Filtration System."

• A reverse osmosis water filtration system is connected to your cold water supply - This can decrease water pressure. See "Water Supply Requirements."

NOTE: If questions remain regarding water pressure, contact a licensed, qualified plumber.

• Doors not closed completely - Make sure both doors are firmly closed. (On some models, only the freezer door must be closed in order to operate the dispenser.)

• Ice maker is not turned on, or ice bin is not installed correctly - Turn on the ice maker and make sure the ice storage bin is firmly in position. See "ice Maker and Storage Bin."

• Ice is clogged or frozen together in the ice storage bin, or ice is blocking the ice delivery chute - Remove or separate the clogged ice, using a plastic utensil if necessary. Clean the ice delivery chute and the bottom of the ice storage bin using a warm damp cloth, then dry both thoroughly. To avoid clogging and to maintain a fresh supply of ice, empty the storage bin and clean both the storage bin and the delivery chute every 2 weeks.

• Wrong ice has been added to the storage bin - Use only ice cubes produced by the current ice maker.

• Dispenser is locked - Unlock the dispenser. See "Water and Ice Dispensers."

• Ice dispenser jams while dispensing crushed ice - For models with the ice storage bin on the door, temporarily switch from crushed ice to cubed ice to clear the iam.

• Dispenser pad/lever has been pressed too long - Ice will automatically stop dispensing. Wait a few minutes for the dispenser to reset, then resume dispensing. Take large amounts of ice directly from the ice bin, not through the dispenser.

• Water pressure to the home is not at or above 30 psi (207 kPa) - The water pressure to the home affects the flow from the dispenser. See "Water Supply Requirements."

• Water filter is clogged or incorrectly installed - Replace filter or reinstall it correctly. See "Water Filtration System."

ICE AND WATER Possible Causes and/or Recommended Solutions

Ice or water has an • New plumbing connections - New plumbing connections can result in off-flavored or discolored ice or water. This off-taste, odor, problem should go away over time.

or gray color

• Ice has been stored too long - Discard the ice and wash the ice bin. Allow 24 hours for the ice maker to produce new

ice.

• Odor has transferred from food - Use airtight moisture-proof packaging to store food.

• Use of non-recommended water supply line - Odors and tastes can transfer from certain materials used in non- recommended water supply lines. Use only a recommended water supply line. See "Water Supply Requirements."

• There are minerals (such as sulfur) in the water - A water filter may need to be installed in order to remove the minerals.

• Water filter was recently installed or replaced - Gray or dark discoloration in ice or water indicates that the water filtration system needs additional flushing. See "Water and Ice Dispensers."

Water dispenser will not operate properly

Water is leaking or dripping from the

dispenser

Water is leaking from the • Water line connections are not fully tightened - Make sure all connections are firmly tightened. See "Connect Water back of the refrigerator Supply."

Water from the dispenser is not cool enough

(on some models)

• Doors not closed completely - Make sure both doors are firmly closed. (On some models, only the freezer door must be closed in order to operate the dispenser.)

• Refrigerator is not connected to o water supply, or the water supply shutoff valve is not turned on - Connect the refrigerator to a water supply and make sure the water shutoff valve is fully open.

• Kink in the water source line - A kink in the water line can reduce water flow to the dispenser. Straighten the water line.

• Water pressure to the home is not at or above 30 psi (207 kPa) - The water pressure to the home affects the flow from the dispenser. See "Water Supply Requirements."

• New installation - After connecting the refrigerator to a water source, flush the water system. See "Water and Ice Dispensers."

• Dispenser is locked - Unlock the dispenser. See "Water and Ice Dispensers."

• Water filter is clogged or incorrectly installed - Replace filter or reinstall it correctly. See "Water Filtration System."

• A reverse osmosis water filtration system is connected to your cold water supply - This can decrease water pressure. See "Water Supply Requirements."

NOTE: If questions remain regarding water pressure, contact a licensed, qualified plumber.

NOTE: After dispensing, a few additional drops of water are normal.

• Glass was not held under the dispenser long enough - Hold the glass under the dispenser for 2 to 3 seconds after releasing the dispenser pad/lever.

• New installation, or water filter was recently installed or replaced - Air in the water lines causes the water dispenser to drip. Flush the water system to remove the air in the water lines. See "Water and Ice Dispensers."

• Residual ice in the dispenser chute is melting - Make sure the ice chute is free of ice shavings or pieces.

NOTE: Water from the dispenser is chilled to 50°F (10°C).

• New installation - Allow 24 hours after installation for the water supply to cool completely.

• Recently dispensed a large amount of water - Allow 24 hours for the new water supply to cool completely.

• Water has not been recently dispensed - The first glass of water may not be cool. Discard the first glass of water dispensed.

• Refrigerator is not connected to o cold water pipe - Make sure the refrigerator is connected to a cold water pipe. See "Water Supply Requirements."

ACCESSORIES

Replacement Parts: To order stainless steel cleaner or replacement filters, call

1-BOO-4-MY-HOME ®and ask for the appropriate part number listed below or contact your authorized Kenmore dealer.

Stainless Steel Cleaner and Polish: Order Part #D22 M40083 R

Water Filter: Order Part #9930 (P4RFKB2 or P4RFKB12)

Air Filten Order Part #W10335147A

Produce Preserver: Order Part #W10335145A

+ 70 hidden pages

Kenmore Elite 10651772510, 10651773510, 10651779510, 10651779511 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual