Kenmore ULTRAFILTER 150 625.385700, ULTRAFILTER 350 625.385720, ULTRAFILTER 150, 625.385700, ULTRAFILTER 350 Owner's Manual

...

Download

OWNER'S

MANUAL

MODEL NO.

UltraFilter 150

625.385700

UltraFilter 350

625.385720

Caution:

Read and Follow

All Safety Rules and Operating Instructions

Before First Use of

This Product.

If you have questions when installing, operating or maintaining your reverse

osmosis system, call this toll-free number...

1-800-426-9345

(M-F, 7am-8pm, CST)

For repair or replacement parts, call this toll-free num-

ber...

1-800-366-7278

See back cover for other

Sears service numbers.

www.KenmoreWater.com

Reverse Osmosis Drinking Water System

_i,Warranty _i, How To Install

_i, How It Works _i, Care Of

_i, Repair Parts

System tested and certified by NSF International

to NSF!ANSl Standard 58 for the reduction of the

claims specified on the performance data sheet.

SAVE THIS MANUAL

PRINTEDtNU.S.A. Part No. 7266568 (Rev. H 8/4/05)

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U. S. A.

- WARRANTY-

F iiiiiiiii iiiiiiiiiiii iiiiiiii _

I I

i (except filter cartridges and R. O. membrane) i

i For one year from the date of purchase, when the Reverse Osmosis Drinking Water System is installed I

and maintained in accordance with our instructions, Sears will repair, free of charge, defects in material

i and workmanship, except filter cartridges and the R. O. membrane. I

I I

I TO OBTAIN WARRANTY SERVICE, SIMPLY CONTACT THE NEAREST SEARS SERVICE CENTER I

THROUGHOUT THE UNITED STATES. This warranty applies only while this product is in use in the

I United States. o

I I

I Thiswarrantygivesy_uspecific_egalrights_andy_umayhave_therrightswhichvaryfr_mstatet_state. I

! I

I Sears, Roebuck and Co., D/817 WA, Hoffman Estates, IL 60179 !

i I il iilll il Ill I il iilll il liliil i J

FULL WARRANTY ON REVERSE OSMOSIS DRINKING WATER SYSTEM

SEARS INSTALLATION POLICY SEARS INSTALLATION WARRANTY

All installation labor arranged by Sears shall be per- formed in a neat, workmanlike manner in accor-

dance with generally accepted trade practices. Fur- ther, all installations shall comply with all local laws,

codes, regulations, and ordinances. Customer shall also be protected during installation by insurance re-

lating to Property Damage, Workman's Compensa- tion and Public Liability.

In addition to any warranty extended to you on the Sears merchandise involved, which warranty be-

comes effective the date the merchandise is installed, should the workmanship of any Sears arranged

installation prove faulty within one year, Sears will, upon notice from you, cause such faults to be cor-

rected at no additional cost to you.

- SAFETY GUIDES -

• Read all steps and guides carefully before instal- ling and using your reverse osmosis system. Follow all steps exactly to correctly install. Reading this manual will also help you to get all the benefits from

the reverse osmosis system.

• Do not attempt to use this product to make safe drinking water from non-potable water sources. Do not use the system on microbiologically unsafe wa- ter, or water of unknown quality without adequate disinfection before or after the system. This system is certified for cyst reduction and may be used on

disinfected water that may contain filterable cysts.

• Check with your local public works department for plumbing and sanitation codes. You must fol-

low their guides as you install the system. Follow your local codes if they differ with guides in this manual. Massachusetts plumbing code 248 CMR shall be adhered to. Please consult your licensed plumber.

• This system shall only be used for arsenic reduc- tion on chlorinated water supplies containing de- tectable residual free chlorine at the system inlet.

Water systems using an inline chlorinator should provide a one minute chlorine contact time before the RO system.

• This system is acceptable for treatment of influ-

ent concentrations of no more than 27 mg/L nitrate and 3 mg/L nitrite in combination measured as N

and is certified for nitrate/nitrite reduction only for water supplies with a pressure of 280 kPa (40 psig) or greater. This system is supplied with a nitrate/ni-

trite test kit. Product water should be monitored pe- riodically according to the instructions provided

with the test kit.

• The reverse osmosis system works on water pres- sures of 40 psi (minimum) to 100 psi (maximum). If your house water pressure is over the maximum, install a pressure reducing valve in the water supply

pipe to the reverse osmosis system.

• Do not install the reverse osmosis system out- side, or in extreme hot or cold temperatures. Temper- ature of the water supply to the reverse osmosis sys-

tem must be between 40°F and 100°F. Do not install on hot water.

• Read the other limits (pH, hardness, etc.) in the specifications and be sure your water supply con- forms. Also see "Water Supply" on page 4.

• The reverse osmosis membrane contains a pre- servative for storage and shipment. Be sure to purge

as instructed on page 11 before using product water.

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- TABLE OF CONTENTS -

Where To Install the RO System ............ 4

Tools and Materials Needed ............... 4

6 Steps to Install ......................... 4

Install Cold Water Supply Fitting ......... 5

Install Drain Adapter ................... 6

Install Faucet ........................... 6

Install RO Assembly .................... 9

Install Storage Tank, Make Tubing

Connections ........................... 10

Sanitizing, Pressure Test, Purging ........ 11

How the RO System Works ............... 12

Care of Your RO System .................. 13

Dimensions, Specifications ................ 18

Remote Installation Locations ............. 19

Repair Parts ............................. 20

- WHAT YOUR REVERSE OSMOSIS SYSTEM WILL DO -

Your Reverse Osmosis (RO) Drinking Water System is a water treatment unit. It uses household water

pressure to reverse a natural physical process called osmosis. Water, under pressure, is forced through a semi-permeable membrane where minerals and im- purities are filtered out. Clean drinking water goes to the faucet or storage, while minerals and impurities

are sent to the drain with RO waste water. The miner- als and impurities are measured in water as total dis-

solved solids (TDS). The system includes replaceable pre and postfilter

sediment-carbon cartridges. The prefilter removes sand, silt, dirt, rust particles, other sediments, and

chlorine from the water supply before it can enter the

RO membrane. The postfilter removes any tastes and/or odors that may remain in the water, after

passing through the RO membrane, and just before going to the RO faucet. To prevent water waste, an

automatic shutoff valve closes when the RO faucet is closed and the storage tank is full.

Your reverse osmosis system gives you a continuous supply of sparkling clear, delicious water for drink- ing, cooking and other uses. Foods will look and

taste better too. Having high quality RO product wa- ter at your fingertips eliminates the need to buy

bottled water. The storage tank holds over 2 gallons

of RO product water for your needs.

- BEFORE YOU BEGIN TO INSTALL THE RO SYSTEM -

FOR OPTIMUM PERFORMANCE YOUR KEN- MORE REVERSE OSMOSIS SYSTEM SHOULD BE

INSTALLED ON SOFTENED WATER. CAUTION: A refrigerator icemaker may not operate

properly when connected to a reverse osmosis sys- tem that has been installed on a water system that op- erates outside of the specified pressures listed on

page 18. Check Your Water Supply: The cold water supply to

the RO system must be within certain quality limits. See the specification table on page 18. If supply water

is not within limits, the RO system can not make product water as it should and reduced RO mem-

brane life will result. Trained sales people at Sears can perform a free water

analysis. This basic test can help determine if any additional water treatment is required before the RO

system.

CAUTION: Chlorine in the water will destroy the RO membrane. Most cities add chlorine to the water

supply to kill bacteria. The prefilter removes chlorine up to the limits shown in the specifications before it

enters the RO membrane. It is important to replace

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

the prefilter cartridge at least every 6 months. See the RO care guide on page 15.

Check Parts Included: Unpack the carton and re- move the RO system. In addition to the assembled

RO and the storage tank, the system includes the parts illustrated below, a separate length of tubing,

and this manual.

TEFLON

TAPE

HANGER WASHERS

& SCREWS

ULTRAFtLTER 150

TUBING

ADAPTER

ULTRAFILTER 350

RO PRODUCT

WATER FAUCET

Figure 1

DRAIN

ADAPTER

WATER SUPPLY

FITTING

- WHERE TO INSTALL THE RO SYSTEM -

The RO assembly and storage tank is designed for installation under the sink, usually in the kitchen or bathroom. The RO assembly mounts on a wall sur- face, or can lay on the cabinet floor next to the storage

tank. Hanger washers and wood screws are included for cabinet wall mounting. The RO product water faucet installs on the sink, or on the countertop next to the sink (page 6).

Note: Tubing lengths allow for the removal of the as- sembly from the hanger washers for servicing. If tub-

ing lengths are shortened for neater appearance, it may be necessary to keep the assembly on the hanger

washers for service. You can also locate the R© assembly and storage tank

RO product RO product

water faucet _ o_ water faucet

UItraFilter 350 UItraFilter 150

/ x

in any remote location from the faucet, observing safety guides on page 2. You do need a nearby water source and drain point (see page 19).

Water Supply: To provide supply water to the RO system inlet use the included feed supply fitting or install pipe fittings for tubing connection, as typical-

ly shown on page 5.

Drain Point: A suitable drain point is needed for re-

ject water from the RO membrane. A floor drain,

laundry tub, standpipe, sump, etc., is preferred, as shown in the remote locations drawing, page 19. A

sink p-trap drain adaptor is included to install where codes permit, as an optional drain point (page 6).

HOT :COLD

sink drain

p-trap

Figure 2

- TOOLS AND MATERIALS NEEDED -

• adjustable wrench, standard pliers, and larger adjustable jaw pliers or pipe wrench to fit sink drain

slotted and Phillips head screwdrivers

plumbers putty

- 6 STEPS TO INSTALL -

STEP 1: - Install Cold Water Supply fittings

STEP 2: - Install Drain Adapter

STEP 3: - Install Faucet

adapter

RO Assembly

• electric drill and bits, if hole is needed for the RO faucet, page 6.

STEP 4: - Install RO Assembly STEP 5: - Install Storage Tank, Make Remaining Tub-

ing Connections STEP 6: - Sanitizing, Pressure Testing, Purging

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- STEP 1: INSTALL COLD WATER SUPPLY FITTING -

Check and comply with local plumbing codes as you plan, then install a cold feed (supply) water fitting. The fitting must provide a leak-tight connection to the RO 1/4" tubing (see Figure 10, page 10). A typical connec-

tion using the included water supply fitting is shown in Figure 3A below. An optional connection, using stan- dard plumbing fittings (not included), is shown in Figure 3B.

Note: Codes in the state of Massachusetts _vquire installation by a licensed plumbe_, and do not permit the use of a saddle valve. For installation, use plumbing code 248-CMR of the Commonwealth of Massachusetts.

A. WATER SUPPLY FITTING

1. Close the house main water shutoff valve and open faucets to drain water from the sink cold water pipe.

2. Remove nut that connects the cold water faucet to cold water plumbing.

3. Use pipe joint compound or Teflon tape on cold water faucet stud threads and on the mate threads of the water

supply fitting that connect to the cold water pipe.

B. OPTIONAL PIPE FITTINGS (compression type shown)

Note: Be sure to turn off the water supply and open

a low faucet to drain the pipe. Complying with plumbing codes, install a fitting on

the kitchen cold water pipe to adapt 1/4" ©D tubing. A typical connection is shown in Figure 3B. If

threaded fittings are used, be sure to use pipe joint compound or Teflon tape on outside threads.

4. Thread water supply fitting onto pipe and reconnect nut to bottom of fitting.

cold water

faucet stud

cold

pipe i ,

waterI I

A. WATER SUPPLY CONNECTION

(using included water supply fitting)

water supply fitting

1/4" green tubing to

RO inlet (see step 2, on

page 8)

B. WATER SUPPLY TYPICAL CONNECTION

(using compression fitting)

- parts not included -

1/4" compression fitting

insert

cold water

shutoff

Figure 3

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

ferrule

cold _ 1/4" tubing to water RO inlet (see step pipe 2, on page 8)

- STEP 2: INSTALL DRAIN ADAPTER -

• Note: Running the drain tubing directly to a floor

drain, sump, standpipe, laundry tub, etc., as shown on page 19, is preferred. However, if that is not pos- sible or practical, the included drain adapter installs in the sink drain pipe, always above or ahead of the

p-trap, Figure 4. Be sure to comply with your local plumbing codes. Other drain pipe fittings, in addi- tion to the adapter, may be needed.

• The drain adapter fits 1-1/2" sink drain pipe.

• The adapter installs directly onto the sink tailpiece

as typically shown in Figure 4 and Figure 5.

• Locate so drain tubing from the faucet makes a

straight run to the adapter, without dips, loops, low spots or kinks.

Note: Consult a plumber if you are not familiar with plumbing procedures.

1. Use a ferrule and nut to assemble the drain tubing connector to the drain adapter (Figure 5). Turn the

connector to about 45 ° from the 12:00 position, as shown (to 10:00 or 2:00 position as needed). Tighten

the nut securely.

P-trap

Figure 4

2. Carefully disassemble the sink drain pipe and clean the tailpiece to assure a leak-tight fit.

3. Install the drain adapter onto the sink tailpiece, using a ferrule and nut. Snug the nut, but do not tighten.

Note: If needed, to make fit, you can cut to shorten the unthreaded end of the adapter. Do not cut too short

so the adapter will make a leak-tight seal with the connecting fitting.

4. Assemble the p- trap to the drain adapter, and oth- er drain pipe fittings as required (check codes) to complete the drain run.

5. Tighten all connections, but do not overtighten and break plastic fittings.

- STEP 3: INSTALL FAUCET -

A. PREPARE MOUNTING HOLE

1. Select one of the following places for the faucet. Be sure it will fit flat against the surface, and there is space underneath for tubing (see Figure 10, page 10).

0 Use an existing sink top hole for a spray hose or other faucet. A 1-1/4" diameter hole is needed.

J Drill a new hole in the countertop next to the sink. t Drill a new hole in the sink top. CAUTION: Drilling holes into countertops made of

stone or solid surface materials such as granite,

ferrule 0

I_yrain adapter black

cut, if _ t X. i

needed 10:00 ./,_ _2:00

Figure 5

marble, Corian:" or other plastic resin products should only be performed by a fabricator installer

who is certified for fabricating such materials. Dril- ling of these type surfaces by any other means may cause permanent, irreparable damage to the counter-

top surface.

2. If drilling is needed, make the 1-1/4" diameter hole.

3. Place plumbers putty around the drilled hole (Figure 6 and Figure 7) to prevent water leakage

around the base of the faucet.

J(__u 45_ 4_.._

dcraoinnnteUbionrg _

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- STEP 3: INSTALL FAUCET (cont.)-

B. ASSEMBLE FAUCET ULTRAFILTER 150

UltraFilter 150

1. Loosely assemble the base, spacer, washer and

plastic nut onto the faucet stud.

2. Route the 1/4" red tubing through the sink or countertop hole and connect to 1/4" barb on faucet.

3. Route the 3/8" black tubing through sink or the countertop hole and connect to 3/8" barb on faucet.

4. Attach the 3/8" blue tubing to the faucet stud us- ing the tubing adaptor.

5. Lower faucet into place on the countertop, on the underside of the countertop or sink slide the slotted washer into place and tighten plastic nut. Tighten

the nut so the faucet cannot move, but do not over- tighten.

b__i_ bers

slotted washer _ (_

washer -......._(_

hex nut _ (_

faucet & spout

H hole in sink or

tubing adaptor

(connects to

1/4" red tubing from RO drain

(connect to 1/4"

barb on faucet)

3/8" blue tubing (connect to stud

on faucet)

Figure 6

/bottom of stud)

3/8" black tubing to

drain point (connect

to 3/8" barb on faucet)

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- STEP 3: INSTALL FAUCET (cont.)-

B. ASSEMBLE FAUCET ULTRAFILTER 350

1. Remove the nut from the faucet threads.

2. Remove the spacer from the threads. To do this, place a finger on either side of the threads and gently

press thumb against the bottom of the faucet threads

(where the quick connect is). The spacer should slide

past the stop.

3. Slide the two attached tubes through the sink or countertop hole, aligning gasket under faucet base.

4. On the underside of the sink or countertop, slide the spacer back onto the faucet threads. The spacer

should align with the tubing in the back. Tighten the nut so the faucet cannot move, but do not overtigh-

ten.

UltraFilter 350

faucet & spout

bezel

gasket

5. Connect tubing. a. Connect the 3/8" blue tubing from the RO system

to the quick connect at the bottom of the faucet threads.

Note: See page 16 for tubing connection instructions.

b. Connect the 3/8" tubing from the faucet to the

drain point (drain adaptor). c. Connect the 1/4" red tubing (supplied with RO)

to the 1/4" tubing attached to the faucet using the 1/ 4" x 1 / 4" quick connector.

6. Remove the spout from the top of the faucet by

pulling it straight upward.

7. Remove the faucet knob by pinching the two lock-

ing tabs inward and then pulling upward on the knob while the tabs are pinched inward. See Figure 8.

8. Push the coin cell battery into the battery holder be-

hind the circuit board. NOTE: the + side of the bat- tery goes against the gold metal bracket.

9. Replace the knob by centering it over the faucet

and aligning the channel on the inside of the knob with the valve lever.

hole in

sink or

coun

spacer J

TUBING

RO SYSTEM

3/8"

tubing

plumbers putty

1/4" tubing to

1/4" red tubing

on RO

3/8" tubing

to drain point

nut

1/4" red

tubing

10. Lower the knob making sure the valve lever

slides into the channel then make sure the top hole in the knob is centered over the locking tabs.

11. Push the spout back into the top of the faucet so

that it is fully seated and push the bezel down until fully seated. You may have to rotate the bezel until it is in position to be fully seated.

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

Figure 7

UltraFilter 350

- STEP 3: INSTALL FAUCET (cont.)-

FAUCET ELECTRONICS

The faucet will measure the length of time the filters have been installed (6 months). The faucet has an in-

dicator LED that flashes to inform you of the status of the filter.

Green - Filter is good. Red - Filters need replacing. In order to reset the monitor time feature, the battery

should be removed for a minimum of five seconds and then reinserted.

channel

locking tabs

valve lever

The battery needs to be replaced when indicater LEDs no longer light. Use only 3 volt sealed lithium

batteries. Improper placement of battery could dam-

age electronics. Use care when inserting battery to align it correctly.

To change the battery, pull the spout and bezel from the faucet base. The bezel will stay on the spout.

Pinch the two tabs (under bezel on faucet) with one hand and with the other, pull up on the knob. Change battery. Assemble the the knob, and spout

and bezel back onto the faucet base.

Figure 8

- STEP 4: INSTALL RO ASSEMBLY -

Hang the assembly on the included hanger washers, or lay on the cabinet floor, as desired.

1. Refer to Figure 9 for wall mounting. Hold the as-

sembly up to the wall surface and mark locations for the hanger washers. Distance needed is 7.2"

(approx. 7-7/32") apart.

2. Install hanger washers at least 15-1/2" up from the

cabinet floor, allowing room to remove sumps from filter heads. Wood screws are provided, or obtain

other fasteners as needed.

15-1/2"

min.

up from

floor

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

Figure 9

- STEP 5: INSTALL STORAGE TANK,

MAKE REMAINING TUBING CONNECTIONS -

1. CONNECT DRAIN TUBING, FAUCET TO

DRAIN ADAPTER: Referring to Figure 10, run the loose section of black 3/8" tubing from the faucet to

the drain adapter, with a black collet, installed on page 6. Cut this tubing as needed to route in as

straight of a run as possible, without loops, dips, low spots or kinks. Cut the end of the tubing square. Then push all the way into the fitting. Pull on the tub- ing to be sure it's held firmly in the adapter fitting.

See page 16 for tubing connection instructions.

2. CONNECT TUBING TO WATER SUPPLY: Con-

nect the feed (green) tube to the water supply fitting installed on page 5. Connection to the fitting is as

RO product

water faucet

UltraFilter 350 2_

described in Figure 14, page 16.

3. Move the storage tank into place next to the RO as- sembly. You can stand the tank upright, or lay it on side. Apply no more than two wraps of Teflon tape to the threads on the nipple at the top of the tank.

Hand tighten the other included tubing adapter fit- ting with the yellow collet onto the tank nipple, then

wrench 1/4 turn only. BE CAREFUL NOT TO CROSS THREAD.

4. Run the 3/8" yellow tubing to the fitting installed in step 3. Be sure the end of the tubing is cut square, and insert all the way into the fitting. Again, pull on

the tubing to be sure it's held firmly in the fitting.

TYPICAL UNDERSINK INSTALLATION

RO product

water faucet

UltraFilter 150

3/8" BLACK TUBING

water supply

fitting

HOT COLD

tubing adaptor yellow collet

Note: See note on page 4

regarding tubing lengths.

drain

adapter

sink p-trap

Figure 10

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- STEP 6: SANITIZING, PRESSURE TESTING & PURGING -

SANITIZING

Sanitizing is recommended upon installation of the

RO system, and after servicing inner parts. It is im- portant for the service person to have clean hands

while handling inner parts of the system. CA UTION: Be sure to remove the RO membrane and

both filter cartridges as follows, before sanitizing.

Chlorine will destroy the RO membrane cartridge.

1. Be sure the water supply to the RO is turned off,

and the RO faucet is open to relieve pressure.

2. Referring to Figure 12, page 14, remove the R©

membrane sump by twisting 1/4 turn left (_D). Re- move the R© cartridge from sump. Place the car- tridge in a clean plastic bag.

3. Be sure the o-ring seal is on the sump. Replace the

RO sump by turning to the right (k,) to lock.

4. Remove the postfilter sump, turning to the left.

Take the cartridge from the sump and place in the plastic bag. Replace the sump by turning to the right

(k_) to lock.

5. Remove the prefilter sump and cartridge. Also

place this cartridge in the clean bag.

6. If needed to clean, flush the prefilter sump with fresh water. Then fill with water to about 1" from the

top. Add 1.0 ounce of chlorine (ordinary 5.25% household bleach...Hilex, Clorox, etc.) and mix in the

water. Do not add chlorine first. Concentrated it will attack plastics.

7. Carefully replace the sump on the prefilter head and turn to the right (k_) to lock.

8. Slowly open the water supply to the RO.

9. Open the R© faucet by turning knob to the left.

10. Allow water to circulate through the R© system until you smell the bleach odor at the faucet. Then

close the faucet and allow the R© to stand idle for 20 minutes.

11. After the 20 minutes open the R© faucet and run water until the bleach odor is gone.

12. Turn off the water supply to the R©.

13. Be sure your hands are clean. Then, repeat steps 1 - 5 and 7, only replace all cartridges.

Important: Refer to Figure 12, page 14, and to page 15 when replacing cartridges. The prefilter (left side)

cartridge and the postfilter (right side) have puple end caps.

PRESSURE TESTING

1. Do the preceding sanitizing procedures before

pressure testing.

2. Open the water supply shutoff valve to the RO.

3. Open the main water supply valve and several

house faucets to purge air from the system. Close faucets when water runs smooth.

PURGING RO MEMBRANE

Important pmxing instructions: The RO cartridge contains afood _ade preservative that should be rinsed before using water from the system. The preserva-

tive will give product water an unpleasant taste and odor.

4. In about 2 hours, pressure will start to build in the RO system. Then, carefully check all fittings and con- nections for water leaks. Correct leaks if any are

found.

Note: When the system is first pressurized, water

may "spurt" from the faucet airgap hole until air is expelled from the RO system.

1. Allow the storage tank to fill for about 4 hours. Then open the R© faucet until the tank is empty and flow stops. Close the RO faucet.

2. Repeat step 1 five more times (for a total of 6) to purge the RO system. Then the RO system is ready

to make product water for use.

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- HOW YOUR REVERSE OSMOSIS SYSTEM WORKS -

PREFILTER

Water from the cold supply pipe enters the RO as- sembly prefilter first (Figure 10, page 10, and sche- matic, page 13).

The prefilter has a replaceable sediment cartridge with activated carbon in its composition. The car- tridge (10 micron) removes sand, silt, dirt, other sedi- ments, and up to the ppm of chlorine shown in the

specifications from the feed water (page 18). Chlo- rine will destroy the RO membrane. Filtered, clean, chlorine- free water flows from the prefilter, to the RO

membrane cartridge.

IMPORTANT: See pref!lter maintenance, page 14.

REVERSE OSMOSIS (RO) CARTRIDGE

The RO cartridge is a tightly wound special mem- brane. The membrane removes the dissolved solids

and organic matter when water is forced through the cartridge. High quality product water (about one ounce per minute) exits the RO cartridge and goes to

the storage tank, or to the postfilter and RO faucet. Reject water, with the dissolved solids and organic

matter, is routed through the flow control and to the drain.

STORAGE TANK

The storage tank holds up to 2.3 gallons of product water. A diaphragm inside the tank keeps water

pressurized to about 30 psi, when the tank is full, to provide fast flow to the RO faucet. The tank, when empty, is pressurized to 5 - 7 psi.

POST FILTER

After leaving the storage tank, but before going to the RO faucet, product water goes through the post filter.

The post filter is an activated carbon type filter. Any remaining tastes and odors are removed from the

product water. Taste-free, odor-free, clean, high quality drinking water is available for use.

FAUCET

The sink or countertop faucet has a hand operated knob to access drinking water. An air-gap is built

into the faucet drain water connection to comply with plumbing codes.

FAUCET ELECTRONICS (UltraFilter 350)

The RO system will monitor the length of time the fil- ters have been installed. The faucet has an indicator

light that flashes to inform you of the status of the fil- ters.

Green - Filters are good. Red - Filters need to be re- placed after 6 months of time has passed.

SHUTOFF ASSEMBLY

To conserve water, the drinking water system has an automatic shutoff system. When the storage tank has

filled to capacity, and the drinking water faucet is closed, pressure closes the shutoff to stop flow to

drain. Pressure in the storage tank is about half of the water supply pressure. After drinking water is used, and pressure in the system drops, the shutoff opens to allow water flow again.

CHECK VALVE

A check valve (Figure 16) is located in the RO man- ifold, above the center sump. The check valve pre- vents a backward flow of product water from the

storage tank. A backward flow could rupture the RO membrane.

FLOW CONTROL

Water flow through the RO membrane is regulated

by the flow control. It maintains the desired flow rate

to obtain the highest quality drinking water. The flow control is located in the end of the 1 / 4" red drain

tubing, at the RO manifold drain port.

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- HOW YOUR REVERSE OSMOSIS SYSTEM WORKS -

REVERSE OSMOSIS WATER FLOW SCHEMATIC

c_--_-'-. FAUCET

air gap

Figure 11

PRODUCT

WATER

BLUE _ PRODUCT WATER

] -o RED I

drain flow I

control _ I

valve I

WATER GREEN _ I I_' I

YELLOW _

" t\ Itl

i AUTOMATIC ' checkI'_l_t_

%r%'Y" 2

PREFILTER MEMBRANE POSTFILTER

- CARE OF YOUR REVERSE OSMOSIS SYSTEM -

To keep your reverse osmosis system operating and producing high quality water, you must make sure supply water is always within the limits shown in the

specifications. Good supply water (soft water is rec- ommended) helps to assure longer life from the RO membrane cartridge, prefilter and postfilter car- tridges. However, each of these will wear out in time

and need replacement.

This reverse osmosis system contains a replace- able treatment component critical for effective

removal of total dissolved solids. The monitor faucet feature provides continuous analysis of the

systems performance. For systems not equipped with the monitor faucet function, it is highly

recommended that you have your water tested at least every 6 months to verify your system is performing properly. Test kits are available by

calling 1-800-826-8553 ext. 47, or check the water testing section of your local phone directory.

If the RO assembly is wall mounted, you may be able to replace parts with the assembly left on the wall. If not, simply lift the RO assembly from the mounting

washers and lay on the cabinet floor when replacing the prefilter and post filter cartridges and RO mem-

brane.

Note: To prevent spillage, place a container under the

RO assembly, or put the RO assembly in a container to catch the water.

CAUTION: Before disconnecting parts, be sure to close the water supply valve to the RO.

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- CARE OF YOUR REVERSE OSMOSIS SYSTEM -

PREFILTER AND POST FILTER CARTRIDGES

You must replace the pref!lter cartridge often to pro- tect the RO membrane from being destroyed by chlorine,

and/or from plugging with sediments in your water supply. If the water supply contains both chlorine and sediments, replace the prefilter cartridge at least every 6 months of product water use. Replace more

often than 6 months if it begins to plug with sedi- ments.

If the water has sediments only, with no chlorine, you may notice a slower making of product water as the

prefilter collects the sediments. When this occurs, re- place the prefilter cartridge. Also replace the post f!lter

cartridge.

To replace the filter cartridges (see Figure 12):

1. Turn off the water supply and open the RO faucet

to relieve pressure.

2. Remove (turn to the left) both sumps from the filter

heads. Be careful...the sumps are full of water.

3. Remove and discard the inner cartridges in a prop-

er manner. Flush the insides of the sumps with fresh water. Do not lose the large o-ring seals.

4. Insert new cartridges with o-ring* seals towards

the top, and with lubricated* o- rings in place, turn to the right to reattach the sumps.

5. Remove and replace batteries to reset counter and

timer. (monitor models). *Note: Use a lubricant approved for use on a potable

water supply.

prefilter

cartridge (cartridge o- ring seals on

this end)

RO Cartridge

(cartridge o-ring

seals on this end

o-ring seal

Turn sumps in the direction of

the arrow to remove. Turn oppo-

site way to install and tighten.

Figure 12

poetfilter

cartridge

(cartridge o-ring

seals on this end)

sump

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- CARE OF YOUR REVERSE OSMOSIS SYSTEM -

RO MEMBRANE CARTRIDGE

The life of the RO membrane cartridge depends

mostly on the pH of the supply water to the RO sys- tem (see specifications). Cartridge life is shorter with

higher pH. For example, if supply water pH is flom 6.8

to 7.7, the cartridge may last for well over one yea1: How- eve_, cartridge life may be as short as 6 months if the pH

is as high as 8.5 to 10. Higher pH weakens the cartridge

membrane and causes pin-hole leaks. It's time to replace the RO cartridge when the pro-

duction rate and/or quality of product water drops. Product water may begin to taste different or bad, in-

dicating solids and organics are passing through the RO membrane. To be sure it is the RO cartridge, re- place the prefilter and postfilter cartridges first.

To replace the RO cartridge (see Figure 12):

1. Turn off the water supply and open the RO faucet to relieve pressure.

2. Remove (turn to the left) the sump from the filter head. Be careful...the sump is full of water.

3. Remove and discard the RO cartridge in a proper manner. Flush the insides of the sump with fresh wa-

ter. Do not lose the large o-ring seals. Note: Sanitizing is recommended after servicing in-

ner parts of the system (see page 11).

4. Insert new RO cartridges with o-ring seals to- wards the top, and with lubricated o-ring in place, turn to the right to reattach the sump.

5. Remove and replace batteries to reset counter and timer. (monitor models).

6. Pu_ige the RO membrane cartridge following instruc- tions on page 11.

FLOW CONTROL

The flow control is vital for proper operation of the RO membrane cartridge. The control keeps water

flow through the membrane at the needed rate to ob- tain the best quality product water.

Periodically check the flow control to be sure the small hole through it is clean and unrestricted.

o-ring sen

let

col-

drain port

flow (control)

insert

1/4" tubing

DRAIN

Figure 13

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- CARE OF YOUR REVERSE OSMOSIS SYSTEM -

TUBING CONNECTION

(all push- in fitting locations)

This RO system includes push-in fittings for quick tubing connection at most locations. If working with the fittings, do the following.

Connection (Figure 14):

1. Use a sharp cutter or knife to cut the end of tubing square.

2. Inspect the end (about 1") of the tubing to be sure there are no nicks, scratches or other rough spots. If needed, cut the tubing again.

3. Push tubing through the collet and all the way into fitting. Full engagement is 11/16" for 1/4" tubing,

and 3/4" for 3/8" tubing. If using tubing other than tubing supplied with the

system, be sure it is of high quality, exact size and roundness with a smooth surface.

Tubing correctly cut and connected

cut tubing s_uare

I I

collet ...__

end of tubing round and

smooth, with no cuts,

nicks or fiat spots

_ 11/16" (1/4" tubing) ' engagement

_ 3/4" (3/8" tubing)

! m 1

I CAUTION I I DO NOT USE VINEGAR OR OTtIER ACID BASED I

I CLEANEI_,SON THIS F,OSYSTEM.THEYWILL I I r)EGRADESOMEI_,OSYSTEMPAP,TS.ALWAYS I

I USE SOAP AN[)WATER. I

! m m.I

This reverse osmosis system contains a replaceable treatment component critical to the efficiency of the

system. Replacement of the reverse osmosis compo- I

I nent should be with one of identical specifications,

as defined by the manufacturer; to assure the same I efficiency and contaminant reduction performance.

! _ m.I

AUTOMATIC SHUTOFF SERVICE

If the shutoff assembly requires service, be sure to reassemble parts exactly as shown in Figure 16.

screw (4)

SHUTOFF ASSEMBLY

diaphragm

Figure 14

To Disconnect Tubing (Figure 15): Push the collet in- ward and hold with a finger while pulling the tubing

out.

Changing Collet and O-ring (Figure 15):

1. With a small screwdriver remove the collet and o-

ring from the fitting. Be careful not to scratch the in- ternal walls of the collet port.

2. Be sure the port is clean, then lubricate and insert the o-ring seal to the bottom of the port.

3. Push the collet inward until it locks in place.

Replacing collet and

o-ring seal

collet (depress to remove tubing)

tubi_/_

Push o-ring seal into bottom of port, then

follow with collet.

_--_fitting

collet

plunger

spacer ring

diaphragm

o-ring

spring

ball

valve

check

Figure 15 Figure 16

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- CARE OF YOUR REVERSE OSMOSIS SYSTEM -

REVERSE OSMOSIS SYSTEM CARE GUIDE

MODEL NOs. 625.385700 & 625.385720

1. AT LEAST every 6 months, replace the prefilter and postfilter cartridges or when red LED flashes,

2. Replace the RO membrane cartridge when the percent rejection of total dissolved solids (TDS) is less than shown in the specifications (see B, below).

3. Replace the battery once per year.

If any of the following occur before the 6 months, replace as directed.

A. Slow Making of Product Water: Replace the prefilter cartridge. C. Chlorine Tasteand/or Odor: Replace the prefilter, post filter and tfthe production rate does not improve, replace the post filter car- RO membrane cartridges.

tridge and RO membrane cartridge. B. High Total Dissolved Solids (TDS) in Product Water: You can

get a free TDS test through some Sears retail stores or service departments, tfthe store or service department does not have a TDS meter, you can send treated and untreated water samples to a water analysis lab for testing. It is important to test both the treated and untreated water to determine system performance. If the TDS is not within the system's performance guidelines, replace the prefilter, post filter and RO membrane cartridges.

OTHER TROUBLESHOOTING

PROBLEM

Chlorine taste and/or odor in the RO product

water

Other taste and/or odor

System makes product Increase water pressure, precondition the water, etc., as needed water too slowly to conform before doing maintenance on the RO system.

System makes lower Open RO faucet and drain tank until flow slows to a drip. Keep

amount of product water faucet open and check tank pressure. If low, pressurize to 6 psi.

than usual Close faucet to refill the tank. High total dissolved sol- Water supply to the RO system not within Increase water pressure, precondition the water, etc., as needed

ids (TDS) in product wa- specifications, to conform before doing maintenance on the RO system, ter RO membrane cartridge expended. Replace the prefilter, postfilter and RO membrane cartridges,

Water leaking from fau- Drain side of faucet airgap (3/8" tubing) Inspect and eliminate restriction or plug. Refer to installation cet airgap hole plugged, restricted, or incorrectly con- instructions for proper drain connection.

Continual water flow to Check valve or automatic shutoff assem- Clean, repair or replace as needed. drain bly plugged, restricted or parts worn

Faucet LED indicator Batteries dead. Replace with new batteries. light does not function af-

ter battery change Batteries installed incorrectly. Install batteries correctly. Continual water flow to Missing flow restrictor in red drain tube or Replace flow restrictor.

drain and no product wa- its corresponding port. ter

Faucet LED indicator Filters needreplacing. Change filters. light flashing red

The ppm of chlorine in your water supply exceeds maximum limits, and has de-

stroyed the RO membrane. The prefilter is no longer removing chlo-

rine from the water supply. Post filter expended.

RO membrane cartridge expended.

Contamination in product water storage. Water supply to the RO system not within

specifications.

Prefilter or RO membrane cartridges plugged with sediments.

Storage tank air-charge less than 5 - 7

psi.

nected to drain point.

CORRECTIONCAUSE

tfthe water supply contains more than 2.0 ppm of chlorine, addi- tional filtering of the water supply to the RO is needed. Correct this condition before doing maintenance on the RO system.

Replace the prefilter, post filter and RO membrane cartridges.

Replace the post filter cartridge. If taste and odor persists, re- place the prefilter cartridge and RO membrane cartridge.

Use sanitizing procedures. Replace the post filter cartridge.

Replace the prefilter cartridge. Ifrate does not increase, replace the postfilter cartridge and RO membrane cartridge.

flow control, and screen.

Note: Sanitizing is recommended after servicing inner parts of the system(see page 11).

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- DIMENSIONS and SPECIFICATIONS -

11"

Supply water pressure limits ........................ 40 - 100 psi

Supply water temperature limits ..................... 40 - 100 °F

Maximum total dissolved solids (TDS) ............... 2000 ppm

Maximum water hardness @ 6.9 pH ................. 10 gpg

Maximum iron, manganese, hydrogen sulfide ......... 0

Chlorine in water supply (max. ppm) ................ 2.0

13"

Metric

280 - 690 kPa

5 - 40°C

Supply water pH limits (pH) ........................ 4 - 10

Product (quality) water, 24 hours ................. 14 gal.

Waste water per gallon of product water ........... 5 gal.

Percent rejection of TDS, minimum (new membrane) _ 90 - 95

Storage tank capacity (max.) ....................... 2.3 gal.

Automatic shutoff control ........................... yes

Efficiency 12 ...................................... 8 %

Recovery 13....................................... 16 %

This system conforms to NSF/ANSI 58 for the specific performance claims as verified and sub- stantiated by test data.

Feed water supply at 50 psi, 77°F, and 750 TDS - Quality water production, amount of waste

water and percent rejection all vary with changes in pressure, temperature and total dissolved solids.

12 Efficiency rating means the percentage of the influent water to the system that is available to the user as reverse osmosis treated water under operating conditions that approximate typical

daily usage. 13 Recovery rating means the percentage of the inftuent water to the membrane portion of the

system that is available to the user as reverse osmosis treated water when the system is operated without a storage tank or when the storage tank is bypassed.

53 liters

18.9 liters

8.7 liters

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- REMOTE INSTALLATION LOCATIONS -

Possible remote locations for the RO nearby the kitchen or bathroom sink include; (1) a basement area

underneath the sink, and (2) an adjacent room or closet. Longer lengths of tubing (see parts list on

page 20) may be needed. You can run the drain tubing directly to one of several

REMOTE RO INSTALLATION

(storage tank not shown)

water faucet

suitable open drain points, as shown below, bypas- sing the faucet airgap and p-trap drain. This type of drain is the preferred over the p-trap drain adapter. Check your local codes. Always be sure to provide an

air gap between the end of the hose and the drain point.

Note: Tubing colors as

supplied with RO system.

1/4" green tubing

3/8" blue tubing /

STANDPIPE

Figure 17

OPTIONAL DRAIN POINTS FOR REJECT WATER

1/4" red

[

airgap I

LAUNDRY

TUB

FLOOR

DRAIN

, \\ [ oo.o

1/4"red _ I X @ _V_TpE_

yellow _ .... _J

storage

tank

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- REPAIR PARTS -

Kenmore Reverse Osmosis Drinking Water System,

Model Nos. 625.385700 & 625.385720

Manifold Housing

PUSH - IN FITTINGS

1/4" _213/8"

o- ring seal

eollet

19_i....... •

1/4" Tubing

14 13

-....

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- REPAIR PARTS -

Kenmore Reverse Osmosis Drinking Water System, Model Nos. 625.385700 & 625.385720

Key Part Description of Part

No. Number

1 7221128 Sump (3 req.) 2 7223633 O-Ring, 2-1/4" x 2-1/2" (3 req.) 3 9006062 Screw (2 req.) 4 9041700 Hanger Washer (2 req.) 5 7234317 Check BalIAssembty 6 7229451 Screw (4 req.)

7 7229532 Automatic Shut-off Cover 8 7250876 Diaphragm Kit

9 7234325 Plunger & Spacer Ring Kit

• 7095030 Cone Screen 10 7265766 Flow (Control) Insert 11 42-38476 Filter, Carbon Block (2 pack)

12 7267962 RO Membrane Cartridge 13 7208544 Connector, 1/4" x 1/4"

14 7208560 Connector, 1/4" x 3/8" 15 7205326 Storage Tank

16 7251034 Connector, 1/4 NPT x 3/8 Tube 17 7208489 Drain Adaptor

Key Part Description of Part

No. Number

18 7227310 Tee, Feed Adaptor 19 7271327 Faucet, Model 625.385700

7266584 Faucet, Model 625.385720

20 7234333 Cover 21 7209566 Push-in Fitting Kit, 1/4" A•

7209574 Push-in Fitting Kit, 3/8" O•

22 7255101 Manifold, incl. key nos. 5 thru 9

• 7266568 Owner's Manual

• - Faucet Battery, Model 625.385720 only, purchase locally, DuraceII

DL2032 or Eveready ECR2032

Optional Accessories and Tubing

• 7161823 Tubing, 1/4"x20'-white [_•

• 7161784 Tubing, 1/4" x 100' - white [_•

• 7157280 Tubing, 3/8" x 20' - white [_•

• 7161750 Tubing, 3/8" x 100' - white _•

• 7122798 Optional Drain Adaptor •

• 42-34707 Suppl. Storage Tank, 3.2 gallon •

• 7123613 Grease for O-Rings •

[] Tubing for remote installations (not included) see page 19, also direct replacement for colored lengths of tub-

ing.

AO See page 20 for use locations - No_e: This o-ring and collet are for replacement in the manifold housing only. They do not fit the other push-in fittings, key nos. 13, 14, 15, 17, 18 and 19.

• not included

• not illustrated

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- NOTES-

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

- NOTES-

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

OWNER'S

MANUAL

MODEL NO.

UltraFilter 150

625.385700

UltraFilter 350

625.385720

The model number of your reverse osmosis

system is found on the rating decal. This decal is

on the back of the R. O. sump.

When requesting service or ordering parts, always provide the following in-

formation:

Reverse Osmosis Drinking Water System

iiiiiiiiiiiii iiiiiiiiiiii

For repair-in your home-of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

.O matter who made it, no matter who sold it!

For the replacement parts_accessories and

owoer'smooua_stb°tt'ooooedtodo-_t-yoorse_.

For Sears professional instaflation of home appliances

,,,,,,,,,,,, HHHHHH

and items like garage door openers and water heaters

1-800-4-MY-HOME _ (1_8004694663}

co,,oo_,mo,0ayor_,g,,<,,.__andc,0°oa_

www.sea_.som www,sears.ca

For repair of carry,-initems tike vacuums, lawn equipment,

and electronics, call or go omline for the location of your nearest

Sears Parts & Repair Center.

ca,,°o_t,_o.,°yo,.o,_,,<usaoo,y_

........................................................._,,._,,,:o0'o..............................................................................

iiiiiiiiiiii_

TOpurchase a protection agreement (U.S.A.)

or maintenance agreement (Canada) on a product serviced by Sears:

1_800-827_6655 (U.S.A,) 1-800_361-6665 (Canada}

Your Home

Our Home

1.8o0488.t===

_I, Product Type _I, Model Number

_I, Part Number _I, Part Description

www.Ken moreWater.com

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Pare pedir sewicio de _eparacie_ Au Canada pour service en francis:

adomicilio,y pareordenarpiezas: 1.80O.LE.FOYER,_,

(1-888W84-6427) v_, sears, ca

_i_ _lqI_e _ ¢ott_Iti_ I¸mi__rqu_ _I_i!_ dt_ _I_ _i)_b_ _n_f CO _I *_:;a_; RO¢*b rA alibi CI

Kenmore ULTRAFILTER 150 625.385700, ULTRAFILTER 350 625.385720, ULTRAFILTER 150, 625.385700, ULTRAFILTER 350 Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual