Kenmore 79640441900, 79640448900 Owner’s Manual

Front-Loading Automatic Washer

Use & Care Guide

Lavadora automat|ca de carga frontal

Manual de uso y cuidado

Models/Modelos 796.4044#9##

Designed to use only HE High Efficiency detergent

DiseSado para utilizar solamente

detergente de alta eficacia

Protocol P172

Sanitization Performance of Residential and Commercial, Family Sized Clothes

Washers

Protocolo P172

Ejecucion de Saneamiento en la zona residencial y comercial, lavodoras del uso del hogar

o ° !ll!

MFL62526816

Sears Brands Management Corporation, Hoffman Estates, |L 60t 79

Sears Canada |nc,, Toronto, Ontario, Canada M5B 2B8

www,sears,com

www,sears,ca

SAFETY MESSAGES ........................................................................... 3

IMPORTANT SAFETY INSTRUCTIONS ........................................... 3-5

GROUNDING INSTRUCTIONS ............................................................. 5

FEATURES AND BENEFITS

Key Parts and Components ................................................................ 6

Included Accessories .......................................................................... 6

Optional Accessories .......................................................................... 6

INSTALLATION REQUIREMENTS

Key Dimensions and Specifications .................................................... 7

Choose the Proper Location ............................................................... 7

Flooring ............................................................................................... 7

Clearances .......................................................................................... 7

INSTALLATION INSTRUCTIONS

Unpacking and Removing Shipping Bolts ........................................... 8

Connecting the Water Lines ................................................................ 9

Connecting the Drain Hose ............................................................... t0

Connect to the Power Supply ........................................................... 10

Leveling the Washer ......................................................................... 11

Installation of non-skid pads (optional) ............................................. 11

HOW TO USE

Control Panel Features ..................................................................... 12

Operating the Washer ....................................................................... 13

Cycle Guide ...................................................................................... 14

Sorting Wash Loads .......................................................................... 15

About the Dispenser ......................................................................... t6

Detergent and Dispenser Use ........................................................... 17

Time and Status Display ................................................................... 18

Cycle Modifier Buttons ...................................................................... t9

Steam Cycles and Options ............................................................... 20

ADD STEAM Option ...................................................................... 20

STEAM REFRESH Cycle .............................................................. 20

Cycle Option Buttons ........................................................................ 21

DELAY START .............................................................................. 21

2ndRINSE ....................................................................................... 21

STAIN TREAT ................................................................................ 21

Special Functions .............................................................................. 21

CONTROL LOCK ........................................................................... 21

CLEAN WASHER .......................................................................... 21

CARE AND CLEANING

Regular Cleaning ......................................................................... 22-23

Cleaning the Exterior ..................................................................... 22

Care and Cleaning of the Interior ................................................... 22

Door Seal and Glass Cleaning ....................................................... 22

Removing Mineral Buildup ............................................................. 22

Storing the Washer ........................................................................ 22

Cleaning the Dispenser .................................................................. 23

Maintenance ................................................................................ 24-25

Cleaning the Water Inlet Filters ...................................................... 24

Cleaning the Drain Pump Filter ...................................................... 25

TROUBLESHOOTING GUIDE

Normal Sounds You May Hear ......................................................... 26

Before Calling for Service ............................................................ 26-29

WARRANTY ........................................................................................ 30

In the space below, record the date of purchase, model, and serial number of your product. You will find the model and serial number printed on an identification plate

located inside the washer door. Have these items of information available whenever you contact Sears

concerning your product. Model No.

Date of Purchase Serial No.

Save these instructions and your sales receipt for future reference.

Master Protection Agreements

Congratulations on making a smart purchase. Your new Kenmore ®product is designed and manufactured for

years of dependable operation. But like all products, it

may require preventive maintenance or repair from time to time. That's when having a Master Protection Agreement can save your money and aggravation.

The Master Protection Agreement also helps extend the

life of your new product. Here's what the Agreement*

includes:

• Parts and labor needed to help keep products operating properly under normal use, not just defects.

Our coverage goes well beyond the product

warranty. No deductible, no functional failure excluded from coverage - real protection.

• Expert service by a force of more than 10,000

authorized Sears service technicians, which means someone you can trust will be working on your product.

• Unlimited service calls and nationwide service, as often as you want us, whenever you want us.

• "No=lemon" guarantee - replacement of your covered

product if four or more product failures occur within

twelve months.

• Product replacement if your covered product can't be fixed.

• Annual Preventive Maintenance Check at your

request - no extra charge.

• Fast help by phone - we call it Rapid Resolution.

Phone support from a Sears representative on all products. Think of us as a "talking owner's manual."

• Power surge protection against electrical damage due to power fluctuations.

• $250 food loss protection annually for any food

spoilage that is the result of mechanical failure of any

covered refrigerator or freezer.

• Rental reimbursement if repair of your covered product takes longer than promised.

• 10% discount off the regular price of any non-covered

repair service and related installed parts

Once you purchase the Agreement, a simple phone call

is all that it takes for you to schedule service. You can call

anytime day or night or schedule a service appointment online.

The Master Protection Agreement is a risk-free purchase.

If you cancel for any reason during the product warranty period, we will provide a full refund, or a prorated refund

anytime after the product warranty period expires.

Purchase your Master Protection Agreement todayT

Some limitations and exclusions apply.

For prices and additional information in the U.S.A.

call 1=800=827=6655.

•Coverage in Canada varies on some items. For full details call Sears Canada at 1=800=361=6665.

Sears Installation Service

For Sears professional installation of home appliances,

garage door openers, water heaters, and other major

home items, in the U.S.A. or Canada call 1-800-4-MY-HOM E®.

Wehaveprovidedmanyimportantsafetymessagesinthismanualandonyourappliance.Alwaysreadandobey allsafetymessages.

Thisisthesafetyalertsymbol. Thissymbolalertsyoutopotentialhazardsthatcanresultinpropertydamageand/orseriousbodily

harmordeath. AllsafetymessageswillfollowthesafetyalertsymbolandeitherthewordDANGERorWARNING.

Thesewordsmean:

Failuretofollowthesesafetyinstructionsmayresultinpropertydamageand/or seriousbodilyharmordeath.

Allsafetymessageswilltellyouwhatthepotentialhazardis,tellyouhowtoreduce thechanceofinjury,andtellyouwhatcanhappeniftheinstructionsarenotfollowed.

ltii/l

To reduce the risk of fire, electric shock, or injury to

persons when using this appliance, follow basic precautions, including the following.

• Before use_the washer must be properly installed as described in this manual.

• Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.

• Do not add gasoline, dry cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

• Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE.

If the hot water system has not been used for such a period, before using the washer, turn ON all hot water

faucets and let the water flow from each for several

minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.

• Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is

used near children.

• Before the washer is removed from service or discarded, remove the door to prevent children from

climbing inside.

•Do not install or store the washer where it will be exposed to the weather or freezing temperatures.

•Do not tamper with controls.

•Do not repair or replace any part of the washer or attempt any servicing other than as described in this manual. We strongly recommend that any service be performed by a qualified individual.

•See Installation Instructions for grounding requirements.

•ALWAYS follow the fabric care instructions supplied by the garment manufacturer.

•Do not place items exposed to cooking oil in your washer. Items contaminated with cooking oils may

contribute to a chemical reaction that could cause a load to catch fire.

•Use fabric softeners or products to eliminate static only as recommended by the manufacturer.

•This washer is not designed for maritime use or for mobile installations such as in RVs, aircraft, etc.

•Turn OFF the water taps and unplug the washer if the machine is to be left tor an extended period of time, such as during vacations.

•Packaging material can be dangerous for children. There is a risk of suffocation! Keep all packaging from

children.

•Always check the inside of the washer for foreign objects before loading laundry. Keep the door closed

when not in use.

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following.

• Unplug the washer before cleaning to avoid the risk of

electric shock.

•Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer. They will damage the finish.

•Do not put oily or greasy rags or clothing on top of the washer. These substances give off vapors that could ignite

the materials.

•Do not wash items that are soiled with vegetable or cooking oil. These items may contain some oil after

laundering and may catch fire.

•Disconnect this appliance from the power supply

before attempting any user maintenance. Turning the

controls to the OFF position does not disconnect this

appliance from the power supply. Failure to follow this warning can cause serious injury, fire, electrical shock, or

death.

• Do not combine detergents, fabric softeners, and other laundry products from different manufacturers for use in one load unless specified on the label.

• Do not mix chlorine bleach with ammonia or acids such as vinegar. Follow package directions when

using laundry products. Incorrect usage can produce poisonous gas, resulting in serious injury or death.

• Do not reach into the washer while parts are moving. Before loading, unloading, or adding items, push in the

cycle selector knob and allow the drum to coast to a complete stop before reaching inside.

Failure to follow this warning can cause serious injury, fire,

electrical shock, or death.

•Refer to INSTALLATION INSTRUCTIONS for detailed grounding procedures. Installationinstructionsare packed

in the washer for installer's reference. If the washer is moved to a new location, have it checked and reinstalled by

a qualified service person. Failure to follow this warning can

cause serious injury, fire, electrical shock, or death.

•Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Failure to follow this warning can cause serious injury, fire, electrical shock, or death.

•For personal safety, this appliance must be properly grounded. Failure to follow this warning can cause serious

injury, fire, electrical shock, or death.

•The power cord of this appliance is equipped with a 3-

prong (grounding) plug which mates with a standard 3- prong (grounding) wall outlet to minimize the possibility

of electric shock hazard from this appliance.

•This washer must be plugged into a 120VAC, 60Hz grounded outlet. Failure to follow this warning can cause serious injury, fire, electrical shock, or death.

•Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. Failure to follow this warning can cause serious

injury, fire, electrical shock, or death.

•Where a standard 2-prong wall outlet is encountered, it

is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

Failure to follow this warning can cause serious injury, fire, electrical shock, or death.

•Do not install on carpet. Install washer on a solid floor.

Failure to follow this warning can cause serious leak

damage.

•Do not remove grounding prong. Do not use an adapter or extension cord. Plug into a grounded 3-

prong outlet. Failure to follow these warnings can cause

serious injury, fire, electrical shock, or death.

•The washer should always be plugged into its own

individual electrical outlet which has a voltage rating that matches the rating plate. This provides the best

performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated

wires.

• Never unplug your washer by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet. Failure to follow this warning can cause serious injury, fire, electrical shock, or death.

• Immediately repair or replace all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. Consult with a qualified service person. Failure to follow this warning can cause serious injury, fire, electrical shock, or death.

•When installing or moving the washer, be careful not to pinch, crush, or damage the power cord. Failure to follow this warning can cause serious injury, fire, electrical

shock, or death.

•The washer must be installed and electrically grounded by a qualified service person in accordance with Iocalcodes to prevent shock hazard and assure stability during operation.

•Washer is heavy. Two or more people may be needed to install and move the appliance. Failure to do so can result in back or other injury.

•Store and install the washer where it will not be exposed to temperatures below freezing or exposed to

outdoor weather conditions. Failure to follow this warning can cause serious leak damage.

•To reduce the risk of electric shock, do not install the washer in humid spaces. Failure to follow this warning can cause serious injury, fire, electrical shock, or death.

• Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children. As children grow, teach them the proper, safe use of all appliances.

Failure to comply with these warnings could result in

serious personal injuries.

• Destroy the carton, plastic bag, and other packing

materials after the washer is unpacked. Children might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight

chambers. Failure to comply with these warnings could

result in serious personal injuries.

•Keep laundry products out of children's reach. To

prevent personal injury, observe all warnings on

product labels. Failure to comply with these warnings could result in serious personal injuries.

•Remove the door to the washing compartment to avoid the danger of children or small animals getting trapped inside before your washer is

removed from service or discarded. Failure to do so can result in serious personal injury or death.

IMPORTANT: Please read carefully.

TO CONNECT ELECTRICITY

Improper connection of the equipment-grounding

conductor can result in risk of electric shock. Check with a qualified electrician or serviceman if you are in

doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the

appliance. If it does not fit the outlet, have a proper outlet installed by a qualified electrician. Failure to follow these warnings can cause serious injury, fire,

electrical shock, or death.

3-prong grounding type

Ensure proper ground exists

before use.

3-prong grounding

plug

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with

all local codes and ordinances.

KEY PARTS AND COMPONENTS

Q DETERGENT DISPENSER

There are four compartments, one each for prewash (not

used on this model) main wash, liquid bleach, and liquid

fabric softener.

O CONTROL PANEL WITH LED DISPLAY

The easy-to-read LED display shows cycle options, settings, cycle status, and estimated time remaining during operation.

NOTE: Sensors in the washer automatically detect the size of the wash load to optimize washing time, based on the selected cycle and options.

DIRECT-DRIVE MOTOR The direct-drive motor provides improved performance

and reliability while increasing energy efficiency.

(Motor is not visible.)

LARGE-CAPACITY STAINLESS STEEL DRUM The ultra-large stainless steel drum offers extreme

durability and is tilted to improve efficiency and allow easier access for large items.

i_) EASY-ACCESS LOCKING DOOR

The extra-large door locks during operation and has a delay feature to prevent the door from being opened until

it is safe to do so.

Hot and Cold

Water Inlets

Power

Cord

il_ FILTER ACCESS PANEL

Provides easy access to the drain pump filter, which allows you to clean the filter or retrieve lost items without

a service call.

(_ LEVELING FEET

Four leveling feet (two in the front and two in the back) adjust to improve washer stability on uneven floors. Feet are adjusted and locked in place using the adjusting

wrench included with the washer.

HIGH-EFFICIENCY STEAM CYCLES

During unique high-efficiency STEAM cycles, the steam

nozzle injects fabrics with hot steam to gently remove tough stains.

Hot and Cold Water Hoses

Included Accessories

Non-skid pads

Caps (4)

(for covering

shipping bolt holes)

Drain

Shipping Bolts/Retainers (4) NOTE: Bolts/retainers MUST be removed prior

to operation. Keep for future use. See page 8.

Optional Accessories

Drain Hose Extension

Rear of Washer

Stacking kit (For dryer)

Wrench (for removing

shipping bolts and

adjusting and

,locking leveling feet)

Tie Strap

(for securing

drain hose

Elbow Bracket

(for securing

drain hose j

P/N 5215ER2002K

D26 17002 (White) D26 17008 (Ginger) D26 17009 (Chili Pepper)

KEY DIMENSIONS AND SPECIFICATIONS

Description Front-Loading Washer Rated Voltage/Frequency 120 VAC @ 60 Hz. Dimensions 27" (W) X 293/4'' (D) X 3811/16'' (H), 511/8'' (D, door open)

68.6 cm (W) X 75.6 cm(D) X 98.3 cm(H), 129.8 cm (D, door open)

Net Weight 190.7 lb. (86.5 kg)

CHOOSE THE PROPER LOCATION

WARNING

• Washer is heavy! Two or more people are required

when moving and unpacking the washer. Failure to do so

may result in damage to property or serious bodily harm.

•Store and install the washer where it will not be

exposed to temperatures below freezing or exposed to outdoor weather conditions. Failure to follow this warning

can cause serious injury, fire, electrical shock, or death.

•Properly ground washer to conform with all governing codes and ordinances. Failure to follow this warning can cause serious injury, fire, electrical shock, or death.

•To reduce the risk of electric shock, do not install the washer in humid spaces. Failure to follow this warningcan cause serious injury, fire, electrical shock, or death.

•The base opening must not be obstructed by carpeting when the washer is installed on acarpeted floor.

•Do not remove ground prong. Do not use an adapter or

extension cord. Plug into a grounded 3-prong outlet.

Failure to follow this warning can cause serious injury, fire, electrical shock, or death.

Power Outlet

•The power outlet must be within 60 in. (1.5 m) of either side of the washer.

•The appliance and outlet must be positioned so that the plug is easily accessible.

•Do not overload the outlet with more than one appliance.

•The outlet must be grounded in accordance with current wiring codes and regulations.

•Time-delay fuse or circuit breaker is recommended,

NOTE: It is the personal responsibility and obligation of the product owner to have a proper outlet installed by a qualified service person.

CLEARANCES

t/3" _'_

(54.2cm)

I_ 293/4" _ I_'1_4"

(75.6 cm) (10cm)

51t/8"

(129.8cm)

To ensure sufficient clearance for water lines and airflow, allow minimum clearances of at least 1 in. (2.5 cm) at the sides and 4 in. (10 cm) behind the unit. Be sure to allow for wall, door, or floor moldings that may increase the required

clearances.

27.

(2.5 cm) (68.6 cm)

1,,

(2.5cm)

FLOORING

•To minimize noise and vibration, the washer MUST be installed on a solidly constructed floor. See the NOTE at

right.

•Allowable slope under the entire washer is a maximum 1" difference from side to side or from front to back.

•Carpeting and soft tile surfaces are not recommended.

•Never install the washer on a platform or weakly supported structure.

Allow at least 211/4in. (54cm) in front of the washer to open the door.

NOTE: Please note that the floor must be strong and rigid enough to support the weight of the washer, when fully loaded, without flexing or bouncing, If your floor has too much flex in it, you may need to reinforce it to make it more rigid. A floor that is adequate for a top-loading washer may not be rigid enough for a front loading washer, due to the difference in the spin speed and direction. If the floor is not solid, your washer may vibrate and you may hear and feel the vibration throughout your house.

UNPACKING AND REMOVING SHIPPING BOLTS

When removing the washer from the carton base, be sure to remove the foam tub support in the middle of the carton base. See drawing below.

If you must lay the washer down to remove the base packaging materials, always protect the side of the washer and lay it carefully on its side. DO NOT lay the washer on its

front or back. To prevent internal damage during transport, the washer is

equipped with 4 shipping bolts and plastic retainers.

IMPORTANT:

•These shipping bolts and retainers MUST NOT be

removed until just before moving the washer into its final position.

•These bolts and retainers MUST be removed before operating the washer.

•Failure to remove shipping bolts and retainers may cause severe vibration and noise, which can lead to permanent damage to the washer.

NOTE: The cord is secured to the back of the washer with a shipping bolt to help prevent operation with shipping bolts in

place.

Shipping Bolts

Power

Cord

1. Starting with the bottom 2 shipping bolts, use the included wrench to fully loosen the 4 shipping bolts by turning them

counterclockwise.

Foam Tub Support

Carton Base

Bolt

Assembly

HoleCap ,

2. Remove the bolt assemblies by wiggling them slightly while pulling.

3. Locate the four hole caps included in the accessory pack and install them in the shipping bolt holes.

NOTE: Save the bolt assemblies for future use. To prevent

damage to internal components, the bolt assemblies must be installed when transporting the washer.

CONNECTING THE WATER LINES

• IMPORTANT: Use new hoses when installing the washer.

Do NOT reuse old hoses.

•IMPORTANT: Use ONLY the inlet hoses provided with this laundry product. Aftermarket hoses are not guaranteed to fit or function correctly. Other hoses may not tighten correctly and could cause leaks. Subsequent damage to product or property will not be covered under the terms of the product warranty.

•Water supply pressure must be between 14.5 PSI and 116 PSI (100~800 kPa). If the water supply pressure is more than 116 PSI, a pressure reducing valve must be installed.

•Periodically check the hose for cracks, leaks, and wear, and replace the hose if necessary.

•Make sure that the water lines are not stretched, pinched, crushed, or kinked.

•The washer should never be installed or stored in a location subject to freezing temperatures. Damage to the

water lines and internal mechanisms of the washer can result. If the washer was exposed to freezing temperatures

prior to installation, allow it to stand at room temperature for several hours before use and check for leaks prior to

operation.

Water Hose

(towaterinlet

on washer) X

RubberSeal

For cold water For hot water

War

2. Attach the red, hot water line to the hot water inlet on the back of the washer. Attach the blue, cold water line to the cold water inlet on the back of the washer. Tighten the fittings securely.

NOTE: Be careful not to cross-thread the hose fittings since this will damage the valve and could result in property damage from leaks.

WaterTap

ilii liiiiiiiiHiiii

Rubber Seal

1. Inspect the threaded fitting on each hose and make sure there is a rubber seal in place in both ends.

Water Hose

(totap)

3. Connect the water supply hoses to the HOT and COLD water faucets tightly by hand and then tighten another 2/3 turn with pliers. Turn ON the water faucets and check

for leaks.

CONNECTING THE DRAIN HOSE

•The drain hose should always be properly secured.

Failure to properly secure the drain hose can result in

flooding and property damage.

•Do not install the end of the drain hose higher than 96 in. (244.8 cm) above the bottom of the washer.

•The drain must be installed in accordance with any applicable local codes and regulations.

•Make sure that the drain hose is not stretched, pinched,

crushed, or kinked.

NOTE: A drain hose extension kit is available if the drain hose is not

long enough. Do not extend drain hose more that 6feet, as

this will cause poor draining

f _DrainHose Extension 1

(_ P/N5215ER2002K

resulting in poor wash and spin performance.

Option 1" Standpipe

Elbow Bracket

Option 2: Laundry Tub

Ilii

The elbow bracket should be installed near the end of the drain hose. Hang the end of the drain hose over the side of

the laundry tub. Use tie strap to secure the drain hose in place.

Elbow Bracket

Tie Strap

Drain Hose

Option 3: Floor Drain

Drain Hose

The elbow bracket should be installed near the end of the drain hose. Insert the end of the drain hose into the

standpipe. Use tie strap to secure the drain hose in place. NOTE:

•Total height of the hose end should not exceed 96 in. (244.8 cm) from the bottom of the washer.

•The drain hose should be inserted no more than 8-12 inches into the standpipe.

NOTE: If the drain hose is extended more than 4 inches beyond the end of the end of the elbow bracket, mold, or

microorganisms could spread to the inside of the washer.

-_ IIII

DrainHose

FloorDrain

Insert the end of the drain hose into the floor drain.

Secure the hose to prevent it from moving.

CONNECT TO THE POWER SUPPLY

Washer should be plugged into a 120-VAC, 60-Hz. grounded 3-prong outlet.

Plug in the washer.

_ J

LEVELING THE WASHER

The drum of your new washerspins at very high speeds. To minimize vibration, noise, and unwanted movement, the floor must be a level, solid surface.

NOTE: Adjust the leveling feet only as far as necessary to level the washer. Extending the leveling feet more than necessary

can cause the washer to vibrate.

sure the floor is clean, dry and free of dust, NOTE: Before installing the washer, make o __@

dirt, water and oils so the washer feet can

not slide easily. Leveling feet that can move

or slide on the floor can contribute to excess ,_....................

vibration and noise due to poor contact with the floor. See INSTALLATION OF

NON-SKID PADS below for more information.

NOTE: If a drip pan must be used, take extra care to follow the instructions provided with the drip pan and make sure the leveling feet are adjusted for firm and even contact with the pan. Use of drip pans and failure to properly level the machine may result in increased vibration and noise during operation.

•All four leveling feet must rest solidly on the floor. Attempt to rock the washer from corner to corner to make sure that all

four leveling feet are in firm contact with the floor.

3. Once the washer is level from side to side and front to back, use the adjusting wrench to tighten all four lock nuts

securely to prevent the legs from getting out of adjustment during operation. Make sure that all 4 leveling feet are in firm contact with

the floor.

NOTE: To make sure that the washer is properly level, run

the washer with a test load: place a medium-sized load of

laundry in the machine. Then press POWER, select RINSE

& SPIN, and then press the START/PAUSE button. See the following sections for additional information on cycle selection and operation. Verify that the washer does not

rock or vibrate excessively during the spin cycle. If the washer vibrates or shakes, adjust the leveling feet, while the washer is spinning, until the vibrations are reduced to a

minimum.

ilii lii:iiiiiHiiii

Leveling

Feet

Leveling Feet

1. Position the washer in the final location, taking specialcare to not pinch, strain, or crush the water and drain lines. Place a level across the top of the washer.

¢22

. Raise Lower ,,

2. Loosen locknuts using the wrench on all 4 leveling feet until you can turn the feet with the included wrench. Turning the leveling foot clockwise lowers the foot and raises the washer;

turning the foot counterclockwise raises the foot and lowers

the washer. Raise or lower the leveling feet until the washer is level from side to side and front to back. Make sure that all

4 leveling feet are in firm contact with the floor. Use a level when adjusting the feet to make sure the washer is level.

NOTE: If you are installing the washer on the optional pedestal, the washer leveling feet should be fully retracted. Use the leveling feet on the pedestal to level the washer.

INSTALLATION OF NON-SKID PADS (optional)

Some floor surfaces are too slippery to prevent the washer

from moving on the floor during heavily unbalanced loads. While it is normal for an occasional load to be out of

balance, excess noise and vibration can result from the

washer moving out of position. If these conditions are

encountered, follow the instructions below for installation of

the non-skid pads. These pads will help prevent the washer from moving during heavy out of balance conditions thereby

reducing noise and vibration.

Non-skid pads

This side up

Stick adhesive side to floor

emove backing

:8 Place the pads under both front feet.

WARNING: To reduce the risk of fire, electric shock, or injury to persons, read and follow this

entire manual, including the Important Safety Instructions, before operating this washer.

CONTROL PANEL FEATURES

; Sfeam • Vibration Guard

START/PAUSE

@ POWER (ON/OFF) BUTTON @

Press to turn the washer ON. Press again to turn the washer OFF.

NOTE: Pressing the POWER button during a cycle will cancel that cycle and any load settings will be lost.

The door will unlock after a brief pause unless the water level or temperature is too high.

g CYCLE SELECTOR KNOB

Turn this knob to select the desired cycle. Once the desired cycle has been selected, the standard presets will be shown in the display. These settings can be adjusted using the cycle setting buttons anytime before starting the cycle. (See the cycle guide on page 14 for allowable settings. To protect your fabrics, not all settings are allowed in all cycles.)

START/PAUSE BUTTON

Press this button to start the selected cycle. If the washer is running, use this button to pause the cycle without losing the current settings.

NOTE : If you do not press the START/PAUSE button within 4 minutes of selecting a cycle, the washer automatically turns OFF.

SPECIAL CYCLE AND OPTION BUTTONS

These buttons are used to activate special cycles or options. See page 21 for details.

TIME AND STATUS DISPLAY The display shows the estimated time remaining, cycle

status, and door lock status. See page 18 for a

complete description.

ADD STEAM BUTTON

Press the ADD STEAM button to add steam to the selected cycle for added cleaning power.

NOTE: Steam can only be added to the following

cycles :Steam Refresh, Normal/Casual,

Bulky/Bedding, Kids Wear, Heavy Duty and Whitest

Whites. See page 20 for details.

DISPENSER

Dispenser drawer. This drawer contains the

compartments for detergent and additives.

See pages 16 -17 for complete information.

CYCLE MODIFIER BUTTONS

Use these buttons to adjust the desired cycle options for the selected cycle. The lights above the buttons show the current selection. See page 19 for a complete description.

NOTE : Not all settings are available on all cycle selections. See chart on page 14 for details.

OPERATING THE WASHER

O SORT LAUNDRY AND LOAD WASHER

Refer to page 15.

ADD DETERGENT AND OTHER PRODUCTS

Open the dispenser drawer and add _detergent to the main wash compartment in the dispenser drawer. Add bleach and fabric softener as

desired. See pages 16 and 17 for important information on detergents and dispenser use.

O TURN ON THE WASHER i_l

Press the POWER button to turn ON the washer. The lights around the Cycle I_iiii.

Selector Knob will illuminate and a chime will sound, if turned ON. Refer to

..... POWER page 12. i_ill

O SELECT A CYCLE

Turn the Cycle Selector Knob either direction to select the desired cycle. The preset Wash/Rinse Temperature, Spin Speed, Soil Level, and Option settings for that cycle will be shown. Refer to page 12.

O SELECT CYCLE MODIFIERS

Default settings for the selected cycle can now be changed if desired. This can be done using the cycle modifier buttons as shown on page 19 (Wash/Rinse, Spin Speed, Soil Level, and Chime). NOTE: To protect your fabrics, not all modifiers are available on all cycles.

(

Add Steam

CleanWasher

START/PAUSE

SELECT CYCLE OPTIONS

Cycle options can also be added using the options buttons as shown on page 20 and 21 (Stain Treat, 2ndRinse, Control Lock, Add Steam, Clean Washer and Delay Start). NOTE: Not all options are available on all cycles.

O BEGIN CYCLE

Press the START/PAUSE button to begin the cycle. Once the cycle has been started, pressing the START/PAUSE again will pause the washer and retain the existing settings for up to 4 minutes.

CYCLE GUIDE

The cycle guide below shows the default settings, available options and recommended fabric types for each cycle. Allowable modifier adjustments are shown below the default setting for each cycle.

= Available option

= Default setting

Steam Refresh

Normal/ Casual

Bulky/ Bedding

Kidswear

HeavyDuty

Cycle

Dressshirts,Blouses (Loadupto 5 garments)

Cotton,linen,towels, shirts,sheets,jeans,

mixedloads

Largeitemssuchas blanketsandcomforters

KidsWear

HeavysoiledCotton Fabrics

50-59

91-97

74-80

)

Warm/Warm

Hot/Cold

Cold/Cold

Warm/Warm

Hot/Cold

Cold/Cold

Warm/Cold

Warm/Warm

Hot/Cold

Cold/Cold

Modifiers

ExtraHigh

NoSpin

Low

Medium

Medium NoSpin

ExtraHigh

NoSpin

Low

Medium

NoSpin

Low

Medium

High

Heavy

Light

Heavy

Light

Normal

Light

Normal

Options

Whitest Whites

Express Wash

ColdClean

Sanitize

Delicates

WhiteFabrics

Lightlysoiledclothingand smallloads

Smallloadsofcotton,linen, towels,shirts,sheets,

jeans,mixedloads

Heavilysoileditems,such asworkclothes,diapers,

etc.

Dressshirts/blouses nylons,sheerorlacy

garments

69-75

57-63

101-107

Cold/Cold

Warm/Cold

Warm/Warm

Cold/Cold

Warm/Cold

Warm/Warm

)

Warm/Cold NoSpin Heavy

Warm/Warm Low Light

ExtraHigh

NoSpin

Low

Medium

NoSpin

Low

Medium

High

ExtraHigh

NoSpin

Low

Medium

ExtraHigh

NoSpin

Low

Medium

Heavy

Light

Normal

Heavy

Light

Heavy

Light

NOTE:To protectyour garments,not every wash/rinsetemperature, spin speed, soil level,or option is availablewith every cycle.

0 NOTE: These cycles usevarious wash motions to enhancecleaning and/orfabric careperformance.

These wash motions may sound different at different stagesofthe washcycle. This isnormal.

NOTE:The washerautomaticallyadjuststhe wash time for the amountof laundry,water pressure,water heatingtime and

other operatingcondition.

SORTING WASH LOADS

Fabric Care Labels

Many articles of clothing include a fabric care label. Using the chart below, adjust the cycle and options selections to care for your clothing according to the manufacturer's

recommendations.

Fabric Care Labels

Machine

wash cycle

Normal Permanent press/ Gentle/

wrinkle resustant delicate

H h Donot wash Doeat wring

Water @@ @ @@ @

temperature Not Warm Cold/coo,

(50°0/120°F) (40°0/105°F) (30°C/85°F)

Bleach

Any bleach Only non-chlorine bleach Donot bleach

(when needed) (when needed)

Grouping Similar Items

For the best washing results and to reduce the possibility of damage to the clothing, care should be taken to sort the clothing into loads that are made up of similar items. Mixing

different fabric types and/or soil levels can poor wash performance, color transfer or discoloration, fabric damage or

lilting. Fabrics should be sorted into groups as described below.

Colors

Sort articles by color. Wash dark clothes together in a separate load from light colors or whites. Mixing dark clothes with light clothes can result in dye transfer or discoloration of the lighter clothes.

Soil Level

Wash heavily soiled clothes together. Washing lightly soiled clothes in the same load with heavily soiled clothes could result in poor wash performance for the lightly soiled clothing.

Fabric Type Delicate articles should not be mixed with heavier or sturdier

fabric types. Washing delicates in a load with heavy fabrics can result in damage to the more delicate fabrics. Washing heavier fabrics in a delicate load can result in poor wash

performance for the heavier fabrics and possible damage to the delicates.

Lint Type Some fabrics attract and bind lint to them while others give off

lint in the laundry process. Avoid mixing these lint collectors and lint producers in the same load. Mixing these fabrics will result in pilling and lilting on the lint collectors. (For example, lint collector - knit sweater; lint producer - terrycloth towels)

Loading the Washer

• Check all pockets to make sure that they are empty.

Items such as clips, matehes, pens, coins, and keys can

damage both your washer and your clothes.

•Close zippers, hooks, and drawstrings to prevent these items from snagging or tangling on other clothes.

• Pretreat heavily stained areas for best results.

•Combine large and small items in a load. Load large items first.

•Large items should not be more than half of the total wash load.

•The washer can be fully loaded, but the drum should not be tightly packed with items. The door of the washer should close easily.

•To prevent an out-of-balance load, do not wash single items. Add one or two similar items to the load. Large, bulky items, such as a blanket, comforter, or bedspread, should be washed individually.

•Do not wash or spin waterproof items, such as rain coats, sleeping bags, etc.

•When unloading the washer, check under the door seal for small items.

NOTE: Make sure the door seal area is clear when closing the door. Overloading the washer can cause items to get caught between the door and the seal. This can damage both

the items and the seal.

DO NOT OVERLOAD THE DRUM

MAKE SURE CLOTHING IS NOT

CAUGHT IN THE DOOR GASKET

by Colors by Soil Whites Heavy

f Sort Laundiy...

Lights Normal Darks Light

by Fabric

Delicates Easy Care

Study

by Lint Lint Producer

Lint Collector

ABOUT THE DISPENSER

The automatic dispenser consists of four compartments which hold:

•Liquid chlorine bleach.

•Liquid fabric softener.

•Liquid or powdered detergent for prewash. (This compartment is not used on this model.)

•Liquid or powdered detergent and color-safe bleach for main wash.

Pre-Wash Detergent Compartment

The dispenser drawer has a compartment that is labeled "Prewash". However, this model does not include a prewash option. Do not put detergent in this compartment. Detergent

in this compartment will not be dispensed and will need to be manually cleaned out.

Main Wash Detergent Compartment

This compartment holds laundry detergent for the main wash cycle; this detergent is added to the load at the beginning of the cycle. Always use HE (High-Efficiency) detergent with your washing machine. Either powdered or liquid detergent

may be used. Never exceed the manufacturer's recommendations when

adding detergent. Using too much detergent can result in detergent buildup in clothing and the washer.

NOTE: Liquid or powdered color-safe bleach may be added

to the main wash compartment with detergent of the same type. DO NOT add liquid or powdered color-safe bleach to

the bleach dispenser. DO NOT mix liquid and powdered cleaning agents within the same compartment.

MainWash Compartment

Compartment (This compartment is not used on this model.)

Liquid Bleach Compartment

This compartment holds liquid chlorine bleach, which will be dispensed automatically at the proper time during the wash cycle.

•Do not add powdered or liquid color-safe bleach to this compartment. The bleach compartment is designed to dispense liquid chlorine bleach only. Powdered or liquid color-safe bleach will not dispense properly.

•Always follow the manufacturer's recommendations when

adding bleach. Do not exceed the maximum fill line since this can cause the bleach to be dispensed immediately causing damage to fabrics. Using too much bleach can damage fabrics.

•Never pour undiluted liquid chlorine bleach directly onto the load or into the drum. Fabric damage can occur.

Fabric Softener Compartment

This compartment holds liquid fabric softener, which will be automatically dispensed during the final rinse cycle.

Never exceed the manufacturer's recommendations when adding softener. Using too much fabric softener can result in

buildup in clothing and the washer. Either powdered or liquid fabric softener may be used.

•Always follow the manufacturer's recommendations when adding fabric softener. Do not exceed the maximum fill line. Using too much fabric softener may stain clothes.

•Dilute concentrated fabric softeners with warm water. Do not exceed the maximum fill line.

•Never pour fabric softener directly onto the load or into the

drum.

Liquid Chlorine Bleach

Compartment

uid Fabric

Softener Compartment

DETERGENT AND DISPENSER USE

A Word About Detergents

HE detergents produce fewer suds, dissolve more efficiently

to improve washing and rinsing performance, and help to

keep the interior of your washer clean. Using non-HE detergent may cause oversudsing and

unsatisfactory performance which could result in error codes,

cycle failure, and machine damage.

_-- MAXIMUM _°--

LIQUID POWDERED

DETERGENT DETERGENT

detergent using the measure provided with the detergent

I For proper wash performance, always measure the

by the manufacturer.

The normal amount needed for average loads is less than

1/2 of the recommended maximum. Use less detergent for soft water, light soil or smaller loads. Never use more than the maximum amount recommended by the detergent

manufacturer.

Normal load amount L_____J

Filling the Dispenser

To add detergent, bleach, and fabric softener to the automatic dispenser:

O Open the dispenser lid.

O Load laundry products appropriate

O Close the lid before the

NOTE: It is normal for a small amount of water to remain in the bleach and softener oompartments at the end of the

cycle. IMPORTANT: Do not place or store laundry products, such

as detergent, bleach, or liquid fabric softener, on top of your washer or dryer. Wipe up any spills immediately. These products can damage the finish and controls.

NOTE: Do not put detergent or other laundry products in the

Prewash compartment. This compartment is not used on this

model

the into the

compartments.

starting cycle.

Designed to use only HE (High-Efficiency) detergent

IMPORTANT: Your washing machine is designed for use with only High-Efficiency (HE) detergents. HE detergents are formulated specifically for front-load washers and contain suds-reducing agents. Always look for the HE symbol when purchasing detergent.

IMPORTANT: Not all detergents are the same. Careful attention must be paid to the amount of detergent used to avoid overusing, poor rinsing and detergent buildup in clothing, and residue buildup that can contribute to odors in

the machine. NEVER use a cup or scoop other than that supplied by the manufacturer of the detergent you are using.

Never use more than the maximum amount recommended by the manufacturer of the detergent.

While HE detergents are designed for this type of washing machine, care must be used when measuring the detergent.

For most normal loads, no more than 1/2 to 3/4 of a cup or scoop of HE detergent should be used.

NOTE: Extra care must be exercised when using 2X and 3X concentrated detergents because even a little bit extra can contribute to the problems mentioned above.

NOTE: Detergents designated as HE-COMPATIBLE may not provide optimal results.

TIME AND STATUS DISPLAY

The time and status display shows the estimated time remaining, cycle progress, and door lock status.

O ESTIMATED TIME REMAINING

When the START/PAUSE is pressed, the washer automatically detects the wash load (weight) and

optimizes the washing time, based on the selected cycle and options. The display will then indicate the estimated time remaining for the selected wash cycle.

NOTE:

•The time shown is estimated. For example, the time displayed may pause for a period of time while the

machine is heating the water or balancing the load, Under certain conditions, the machine can pause for

extended periods of time,

•Estimated time is based on normal operating conditions.

Several external factors (room temperature, incoming

water temperature, etc.) also affect the length of

estimated time vs. actual time.

O LOAD-SENSING INDICATOR

This light will illuminate at the beginning of the cycle while the control measures the size of the load. Once the size

has been determined, the control will adjust the cycle for optimum performance. Estimated time remaining will not be displayed until the load size has been determined and may be different for each load.

_ CYCLE STATUS INDICATOR

These status LEDs illuminate to indicate which portion of the cycle is currently running. A blinking light indicates the

active portion of the cycle. When that portion is complete,

the light will remain steady.

_DOOR LOCK INDICATOR

Indicates that the door is locked. The washer door will lock

while the washer is operating, The door can be unlocked

by pressing the START/PAUSE to pause the washer. NOTE:

• If the temperature in the washer is too high, the door cannot be unlocked until the washer has cooled.

• If the water level is too high, the door will not unlock. To drain the water, press POWER, then press the SPIN SPEED button without selecting a cycle, Press

START/PAUSE and the water will be drained and the clothes will be spun out. Do not try to force the door

open, as it will damage the door.

CYCLE MODIFIER BUTTONS

Each cycle has default settings that are selected automatically. You may also customize these settings using the cycle modifier buttons. Press the button for the desired modifier until the indicator light for the desired value is lit. The washer automatically adjusts the water level for the type

and size of wash load for best results and maximum efficiency. Due to the high-efficiency nature of this product,

water levels may be much lower than expected. This is normal operation and cleaning/rinsing performance will not be compromised.

ExtraHot/Cold

Hot/Cold

Warm/Warm

Warm/Cold

Co,dicO,d

Wash/Rinse Spin

Extra High

High

Medium

Low

No Spin

NOTE: To protect your garments, not every wash/rinse temperature, spin speed, soil level, or option is available with every cycle. See the Cycle Guide on page 14 for details.

Heavy

Normal

Light

Soil Level

Loud

Soft

Off

O WASH/RINSE

Selects the wash and rinse temperature combination for the selected cycle. Press the WASH/RINSE button until

the indicator light for the desired setting is lit.

•Your washer features a heating element to boost the hot water temperature for Extra Hot settings. This provides improved wash performance at normal

water heater settings.

•Select the water temperature suitable for the type of load you are washing. Follow the garment fabric care labels

for best results.

•Warm rinses are regulated at approximately 86°F (30°C).

•Warm rinses leave the clothes drier than cold rinses, but will result in increased energy consumption and greater

wrinkling of clothes.

•Cold rinses use less energy. The actual rinse temperature depends on the temperature of the cold

water at the faucet.

g SPIN SPEED

This extracts more water from clothes, reducing drying time and saving energy.

Press the SPIN SPEED button until the indicator light for the desired setting is lit. Some fabrics, such as delicates,

require a slower spin speed. The Drain & Spin cycle:

1. Press the POWER button to turn ON the washer.

2. Press the SPIN SPEED button to select the desired spin speed. For drain only, select the NO SPIN option.

3. Press the START/PAUSE button. The water will be drained and the clothes will be tumbled before the

spin routine begins.

(_ SOIL LEVEL

Adjusts the selected cycle to allow more time for heavily soiled clothes or less time for lightly soiled clothes.

Press the SOIL LEVEL button until the indicator light for the desired setting is lit.

_) CHIME

Press repeatedly to adjust the volume of the chime. You may turn the end-of-cycle chime and keypad tones

on or off with the CHIME button.

STEAM CYCLES AND OPTIONS

ADD STEAM Option

Steam cycles include the Steam Refresh, Normal/Casual, Bulky/Bedding, Kids Wear,

..... Heavy Duty and Whitest Whites. Adding

Add Steam steam to these cycles provides superior

cleaning performance while reducing

energy and water consumption. By using a hot steam spray from above and cooler water

below, fabrics get the cleaning benefits of asuper hot wash, without the energy usage or potential damage to fabrics.

To ADD STEAM to a cycle:

O Turn on the washer and turn the cycle selector knob to

select a cycle that allows the steam option.

t_ Press the ADD STEAM button. The washer will

automatically adjust the cycle settings. O Set any other desired options. O Press the START/PAUSE button to start the cycle.

CAUTION:

The door may become quite warm during steam cycles. This is normal.

Do not attempt to override the door lock mechanism or reach into the washer during a steam cycle. Steam can cause

severe burns. IMPORTANT NOTES ABOUT STEAM CYCLES:

•Steam may not be visible during the steam cycles. This is normal.

•Do not use steam with delicate fabrics such as wool, silk, or easily discolored fabrics.

Using the STEAM REFRESH Cycle

STEAM REFRESH uses the power of steam alone to quickly

reduce wrinkles and odor in fabrics. It brings new life to

wrinkled clothes that have been stored for an extended time and makes heavily wrinkled clothes easier to iron. STEAM

REFRESH can also be used to help reduce odors in fabrics.

To use the STEAM REFRESH cycle:

Turn on the washer and turn the cycle selector knob to select the STEAM REFRESH cycle.

Load up to 5 items and close the door.

NOTE: If there is any moisture inside the drum, such as from a previous wash cycle, wipe the drum dry with a towel before adding clothes.

Press the ADD STEAM button until the correct number

O of items is shown in the display.

No other options need to be set. The cycle is designed to refresh from 1 to 5 garments.

O Press the START/PAUSE button to start the

After the STEAM REFRESH cycle is complete, the washer will tumble the clothes for up to 30 minutes to prevent clothes from becoming wrinkled again.

After removing clothes from the STEAM REFRESH cycle, they may feel slightly damp. If desired, hang clothes on a

hanger for a few minutes before wearing.

•The STEAM REFRESH cycle is not recommended for use with 100% cotton clothing. Best results can be obtained with 70/30 cotton/poly blend fabrics.

• Remove stains from clothing before using the STEAM

REFRESH cycle; the high heat could cause stains to set

permanently.

• Do not use STEAM REFRESH with the following items:wool, blankets, leather jackets, silk, wet clothes, lingerie, foam products, or electric blankets.

• Best results are achieved when articles are of similar size and fabric type. Do not overload.

cycle.

+ 44 hidden pages