Kenmore 790.75747991, 790.75748991, 790.75742991, 790.75741992, 790.75742992 Installation Instructions Manual

For Models with 2 Standard and 2 Large Sealed Surface Burners

INSTALLATION AND SERVICE MUST BE PERFORMED BY

A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

THIS CONVERSION KIT MUST BE INSTALLED BY A QUALIFIED SERVICE TECHNICIAN

IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS AND ALLAPPLICABLE CODES AND
REQUIREM ENTS OF TH E AUTHORITY HAVING JU RISDICTION. FAILURE TO FOLLOW INSTRUCTIONS

MAY RESULT IN FIRE, EXPLOSION OR PRODUCTION OF CARBON MONOXIDE CAUSING PROPERTY
DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. THE QUALIFIED SERVICE AGENCY IS RESPONSIBLE

FOR THE PROPER INSTALLATION OF THIS KIT. THE INSTALLATION IS NOT PROPER AND COMPLETE
UNTIL THE OPERATION OF THE CONVERTED APPLIANCE IS CHECKED AS SPECIFIED IN THE

MANUFACTURER'S INSTRUCTIONS SUPPLIED WITH THE KIT.

BEFORE PROCEEDING WITH THE CONVERSION, SHUT OFF THE GAS SUPPLY BEFORE

DISCONNECTING ELECTRICAL POWER TO THE RANGE. BE SURE BOTH POWER SUPPLIES ARE OFF
BEFORE INSTALLING THE CONVERSION KIT. FAILURE TO DO SO COULD CAUSE SERIOUS BODILY

INJURY.

This kit contains the following:

Quantity Description Part Number

1

2

2
2

2

Surface Burner Orifice Marked 0.89 mm (7,500 BTU*) 316010802
Surface Burner Orifice Marked 1.00 mm (10,000 BTU*) Green 316010803
*For operation at elevations above 2000 ft., appliance rating shall be reduced at the rate of 4 percent for each

1000 ft. abovesealevel.
installation Instructions
Restrictor-Burner

Screw-Restrictor

Choke-Burner: Small (7,500 BTU) Surface Burners
Choke-Burner: Large (10,000 BTU) Surface Burners

316105826
316011600

316064200
316056700

316O863O0

Tools Required:

#1 Phillips Head Screwdriver (small)

5/8" Open End Wrench ___j w_mmm_

1/8" Wide Flat Blade Screwdriver
7mm Nutdriver

J

J

Espa_ol - P,_ginas 7-12

P/N 316105826 (0001)

1

How to Convert the Range for use

with LP/Propane Gas

1. Convert the Pressure Regulator

To access the regulator, remove the kick panel, storage

drawer or warmer drawer. If equipped with a broiler
drawer, open drawer completely. For models equipped

with warmer drawer, follow the instructions below to

remove warmer drawer.

a, _ Electrical Shock Hazard can occur and

result in serious injury or death, Disconnect electrical
power to the range before removing the warmer

drawer for servicing.
b. Open the drawer to the fully opened position.
c, Locate glide lever on each side of drawer, pull up on the

left glide lever and push down on the right glide lever

(see figure 1).
d. Pull the drawer away from the range.

Pullup withfinger

Left Glide

RightGlide

.....[]Lever

Pus_

FIGURE 1

Front Access

to Regulator:

Remove Kick Panel,

StorageDrawer, or

Warmer Drawer.

(See Owner's Guide

for Instructions).

If Equipped with

Broiler Drawer,

pen Broiler Drawer.

FIGURE 2

Pressure

Regulator

location at

rear of

range

e. Do not remove the Pressure Regulator or allow it to

rotate or turn, Remove the dust protector from the

cap. Using a 5/8" wrench, unscrew the cap from the

pressure regulator. Do not remove the spring from

the regulator. Do not pull on spring.

f. Turn the cap over so the hollow end faces outward.

Place the solid end of the cap into the loop end of the
dust protector as shown in illustration below.

g. Replace the cap on the regulator. The letters LPshould

be visible on the exposed end of the cap, Snap the dust
protector over the regulator cap.

Dust

Protector

Hollow End Solid End

Towards Towards

Regulator Regulator

for Natural Gas for LP/Propane Gas

FIGURE 3