Kenmore 640-06219874-2, 13934172410 Owner’s Manual

Use & Care Guide Manual de Uso y Cuidado

English / Espafiol

I(enmoreo

Liquid PropaneGas Grill

Parrilla a gas de propane liquido

Model/ModUlo: Item/Arffculo:

139.34172410 - Stainless Steel 640-06219874-2 - Acero Inoxicloble

P/N 3104264

Sears Brands Management Corporation

Hoffman Estates, IL 60179 U.S.A www.kenmore.com www.sears.com

www.kmart.com

If you smell gas:

1.Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department.

1.Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance.

2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any

other appliance.

Installation Safety Precautions

• Use grill, as purchased, only with LP (propane) gas and the regulator/valve assembly supplied. A conversion kit must

be purchased for use with natural gas.

• Grill installation must conform with local codes, or in their absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2, or the Standard for Recreational Vehicles, ANSI A 119.2/NFPA 1192, and CSA Z240 RV Series, Recreational Vehicle Code, as applicable.

• All electrical accessories (such as rotisserie) must be electrically grounded in accordance with local codes, or

National Electrical Code, ANSI / NFPA 70 or Canadian Electrical Code, CSA C22.1. Keep any electrical cords and/or fuel supply hoses away from any hot surfaces.

• This grill is safety certified for use in the United States and/or Canada only. Do not modify for use in any other

location. Modification will result in a safety hazard.

IMPORTANT: This grill is intended for outdoor use and is not

intended to be installed in or on recreational vehicles or boats.

NOTE TO INSTALLER: Leave this Use & Care Guide with the

customer after delivery and/or installation.

Call Grill Service Center For Help And Parts If you have questions or need assistance during assembly,

please call 1-800-482-0131. You will be speaking to a representative of the grill manufacturer and not a Sears employee. To order new parts call Sears at

1-800-4-MY-HOME.

Product Record IMPORTANT: Fill out the product record information

below.

Model Number

Serial Number

See rating label on grill for serial number.

Date Purchased

NOTE TO CONSUMER: Leave this Use & Care Guide in a convenient place for future reference.

Safety Symbols The symbols and boxes shown below explain what each

heading means. Read and follow all of the messages found throughout the manual.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death

or serious injury.

WARNING: Indicates an potentially hazardous situation which, if not avoided, could result in

death or serious injury.

For residential use only. Do not use for

commercial cooking.

CAUTION: Indicates a potentially hazardous situation or unsafe practice which, if not avoided,

may result in minor or moderate inju_.

For Your Safety .................................. 2

Grill Service Center ............................... 2

Product Record Information ........................ 2

Safety Symbols ................................... 2

Installation Safety Precautions ....................... 2

Kenmore Grill Warranty ........................... 3

Use and Care .................................. 4-11

Parts List ....................................... 12-17

Parts Diagram ..................................... 18

Assembly ....................................... 19-28

Troubleshooting ................................. 29-30

Repair Protection Agreements Congratulations on making a smart purchase. Your new

Kenmore @product is designed and manufactured for years of dependable operation. But like all products, it may require

repair from time to time. That's when having a Repair Protection Agreement can save you money and aggravation.

Purchase a Repair Protection Agreement now and protect yourself from unexpected hassle and expense.

Here's what the Repair Protection Agreement includes: m Expert service by our 10,000 professional repair

specialists

m Unlimited service and no charge for parts and labor on

all covered repairs

m Product replacement up to $1500 if your covered

product can't be fixed

m Discount of 25% from regular price of service and

related installed parts not covered by the agreement; also, 25% off regular price of preventive maintenance check

m Fast help by phone - we call it Rapid Resolution -

phone support from a Sears representative. Think of us

as a "talking owner's manual."

Once you purchase the Repair Protection Agreement, a simple phone call is all that it takes for you to schedule service. You

can call anytime day or night, or schedule a service appointment online.

The Repair Protection Agreement is a risk-free purchase. If you cancel for any reason during the product warranty period, we

will provide a full refund. Or, a prorated refund anytime after the product warranty period expires. Purchase your Repair

Protection Agreement today!

Some limitations and exclusions apply. For prices and additional information call 1-800-827-66SS.

Sears Installation Service For Sears professional installation of home appliances, garage

door openers, water heaters, and other major home items, in the U.S.A. call 1-800-4-MY-HOME®

Kenmore One Year Limited Warranty When installed, operated and maintained according to all

supplied instructions, if this appliance fails due to a defect in material and workmanship within one year from the date of

purchase, call 1-800-4-MY-HOME ® to arrange for free repair or replacement if repair is unavailable.

For five years from the date of purchase, any burner that rusts through will be replaced free of charge. After the first year from the date of purchase, you are responsible for the labor

cost to have it installed. All warranty coverage excludes ignitor batteries and grill part

paint loss, discoloration or surface rusting, which are either expendable parts that can wear out from normal use within the warranty period, or are conditions that can be the result

of normal use, accident or improper maintenance. All warranty coverage is void if this product is ever used while

providing commercial services or if rented to another person.

This warranty covers ONLY defects in material and workmanship. Sears will NOT pay for.

1. Expendable items that can wear out from normal use within the warranty period, including but not limited to batteries,

light bulbs and surface coatings or finishes.

2. A service technician to instruct the user in correct product installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed, operated or maintained according to the all instructions supplied with the product.

5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those

recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

Disclaimer of implied warranties; limitation of remedies Customer's sole and exclusive remedy under this limited

warranty shall be product repair as provided herein. Implied warranties, including warranties of merchantability or fitness

for a particular purpose, are limited to one year or the shortest period allowed by law. Sears shall not be liable for

incidental or consequential damages. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitation on the duration of

implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to you.

This warranty applies only while this appliance is used in the United States.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears Brands Management Corporation, Hoffman Estates, IL

60179

• NEVER store a spare LP cylinder under or near the grill appliance or in an enclosed area.

• Never fill a cylinder beyond 80% full.

• If the information in the two points above is not followed exactly, a fire causing death or serious

injury may occur.

• An over filled or improperly stored cylinder is a hazard due to possible gas release from the

safety relief valve. This could cause an intense fire with risk of property damage, serious injury or death.

• If you see, smell or hear gas escaping, immediately get away from the LPcylinder and grill appliance and call your fire department.

LP Cylinder

• The LP cylinder used with your grill must meet the following requirements:

• Use LP cylinders only with these required measurements: 12" (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) capacity maximum.

• LP cylinders must be constructed and marked in accordance with specifications for LP cylinders of the U.S. Department of

Transportation (DOT) or for Canada, CAN/CSA-B339, cylinders, spheres and tubes for transportation of dangerous

goods. Transport Canada (TC). See LP cylinder collar for marking.

• LP cylinder valve must have:

• Type 1 outlet compatible with regulator or grill.

• Safety relief valve.

• UL listed Overfill Protection Hand Wheel Device (OPD). This OPD safety

feature is identified by a unique triangular hand wheel. Use only LP cylinders equipped with this type of valve.

• LP cylinder must be arranged for vapor withdrawal and include collar to protect LP cylinder valve. Always keep LP

cylinders in upright position during use, transit or storage.

LP Tank Removal, Transport and Storage

• Turn OFF all control knobs and LPtank valve. Turn coupling nut counterclockwise by hand only - do not use tools to

disconnect. Lift LP tank wire upward off of LP tank collar, then lift LPtank up and off of support bracket. Place the dust

cap on cylinder valve outlet whenever the cylinder is not in use.

Only install the type of the dust cap of the cylinder valve outlet

that is provided with the cylinder valve. Other types of caps or

plugs may result in leakage pf propane. Failure to use safety cap as directed may result in

serious personal injury and/or property damage.

LP Tank Valve

Cap

Retainer Strap

• A disconnected LP tank in storage or being transported must

have a safety cap installed (as shown). Do not store an LP tank in enclosed spaces such as a carport, garage, porch, covered patio or other building. Never leave an LP tank inside

a vehicle which may become overheated by the sun.

• Do not store an LP tank in an area where children play.

LP cylinder in upright position for vapor withdrawal

LP (Liquefied Petroleum Gas)

• LPgas is nontoxic, odorless and colorless when produced. For Your Safety, LP gas has been given an odor (similar to

rotten cabbage) so that it can be smelled.

• LPgas is highly flammable and may ignite unexpectedly

when mixed with air.

LP Cylinder Filling

• Use only licensed and experienced dealers.

• LPdealer must purge new cylinder before filling.

• Dealer should NEVER fill LPcylinder more than 80% of LP cylinder volume. Volume of propane in cylinder will vary by

temperature.

• A frosty regulator indicates gas overfill. Immediately close LP cylinder valve and call local LP gas dealer for assistance.

• Do not release liquid propane (LP) gas into the atmosphere. This is a hazardous practice.

• To remove gas from LP cylinder, contact an LP dealer or call a local fire department for assistance. Check the telephone

directory under "Gas Companies" for nearest certified LP dealers.

LPTankExchange

•Manyretailersthatsellgrillsofferyoutheoptionofreplacing youremptyLPtankthroughanexchangeservice.Useonly

thosereputableexchangecompaniesthatinspect,precision fill,testandcertifytheircylinders.Exchangeyourtankonly

foranOPDsafetyfeature-equippedtankasdescribedin the"LPTank"sectionofthismanual.

•AlwayskeepnewandexchangedLPtanksinuprightposition duringuse,transitorstorage.

•LeaktestnewandexchangedLPtanksBEFORE connectingtogrill.

Connecting Regulator To The LP Tank

1. LPtank must be properly secured onto grill. (Refer to assembly section.)

2. Turn all control knobs to the OFF position.

3. Turn LPtank OFF by turning OPD hand wheel clockwise to a full stop.

4. Remove the protective cap from LP tank valve. Always use cap and strap supplied with valve.

OPD Hand Wheel

LPTankLeakTest Foryoursafety

•LeaktestmustberepeatedeachtimeLPtankisexchanged orrefilled.

•Donotsmokeduringleaktest.

•Donotuseanopenflametocheckforgasleaks.

•Grillmustbeleaktestedoutdoorsinawell-ventilatedarea, awayfromignitionsourcessuchasgasfiredorelectrical

appliances.Duringleaktest,keepgrillawayfromopen flamesorsparks.

•Usea cleanpaintbrushanda50/50 mild soap and water

solution. Brush soapy solution onto areas indicated by arrows in figure below. Leaks are indicated by growing bubbles.

If "growing" bubbles appear do not use or move the LP

tank. Contact an LP gas supplier or your fire department!

_, Do not use household cleaning agents. Damage to gas

train components (valve/hose/regulator) can result.

Type 1 outlet with thread on outside

Safety Relief

Strap and cap

Do not insert a POL transport plug (plastic part with external threads)

into the Type 1 tank valve outlet. It will defeat the Safety Relief Valve

feature.

5. Hold regulator and insert nipple into LP tank valve. Hand-tighten the coupling nut, holding regulator in a straight

line with LP tank valve so as not to crossthread the

connection.

Nipple has to be centered into the LP tank valve.

Hold coupling nut and regulator as shown for proper connection

to LP tank valve.

6. Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal on the back-check feature in the LP

tank valve, resulting in some resistance. An additional one-half to three-quarters turn is required to complete

the connection. Tighten by hand only - do not use tools.

NOTE: If you cannot complete the connection, disconnect regulator

and repeat steps 5 and 6. If you are still unable to complete the connection, do not use this regulator! Call 1-800-482-0131

for assistance.

Leak Testing Valves, Hose and Regulator

1.Turn all grill control knobs to OFF.

2. Be sure regulator is tightly connected to LPtank.

3. Completely open LP tank valve by turning OPD hand wheel counterclockwise. If you hear a rushing sound, turn gas off

immediately. There is a major leak at the connection. Correct before proceeding by calling Sears for

replacement parts at 1-800-4-MY-HOME®.

4. Brush soapy solution onto areas where bubbles are shown in picture below:

A Never remove threaded

orifice at end of valve.

° Do not insert any tool or foreign object into the valve

outlet or safety relief valve. You may damage the valve and cause a leak. Leaking propane may result in explosion, fire, severe personal injury, or death.

° Outdoor gas appliance is not intended to be installed

in or on a boat.

° Outdoor gas appliance is not intended to be installed

in or on an RV.

° Never attempt to attach this grill to the self-contained

LP gas system of a camper trailer or motor home.

° Do not use grill until leak-tested. ° If a leak is detected at any time, STOP and call the

fire department.

° If you cannot stop a gas leak, immediately close

LPcylinder valve and call LP gas supplier or your fire

department!

5. If "growing" bubbles appear, there is a leak. Close LP tank valve immediately and retighten connections. If leaks

cannot be stopped do not try to repair. Call Sears for

replacement parts at 1-800-4-MY-HOME®.

6. Always close LPtank valve after performing leak test by turning hand wheel clockwise.

For Safe Use of Your Grill and to Avoid Serious Injury:

* Do not let children operate or play near grill. * Keep grill area clear and free from materials that

burn.

* Do not block holes in sides or back of grill. * Check burner flames regularly.

" Use grill only in well-ventilated space. NEVER use in

enclosed space such as carport, garage, porch, covered patio, or under an overhead structure of any

kind.

" Do not use charcoal or ceramic briquets in a gas grill.

(Unless briquets are supplied with your grill.)

* Use grill at least 3 ft. from any wall or surface.

Maintain 10 ft. clearance to objects that can catch fire, or to sources of ignition such as pilot lights on water heaters, live electrical appliances, etc.

Safety Tips

slL Before opening LPcylinder valve, check the coupling nut

for tightness.

slk When grill is not in use, turn off all control knobs and LP

cylinder valve.

slL Never move grill while in operation or still hot. slk Use long-handled barbecue utensils and oven mitts to

avoid burns and splatters.

slk Maximum load for side burner and side shelf is 10 Ibs.

The grease tray must be inserted into grill and emptied

slk after each use. Do not remove grease tray until grill has

completely cooled.

slk Clean grill often, preferably after each cookout. If a bristle

brush is used to clean any of the grill cooking surfaces, ensure no loose bristles remain on cooking surfaces prior

to grilling. It is not recommended to clean cooking surfaces while grill is hot.

slk If you notice grease or other hot material dripping from grill

onto valve, hose or regulator, turn off gas supply at once. Determine the cause, correct it, then clean and inspect

valve, hose and regulator before continuing. Perform a leak test.

slL Keep ventilation openings in cylinder enclosure (grill cart)

free and clear of debris.

slL Do not store objects or materials inside the grill cart

enclosure that would block the flow of combustion air to the underside of either the control panel or the firebox bowl.

slL The regulator may make a humming or whistling noise

during operation. This will not affect safety or use of grill.

slk If you have a grill problem see the "Troubleshooting

Section".

silk If the regulator frosts, turn off grill and LPcylinder valve

immediately. This indicates a problem with the cylinder and it should not be used on any product. Return to supplier!

• Apartment Dwellers:

Check with management to learn the requirements and fire codes for using an LP gas grill in your

apartment complex. If allowed, use outside on the ground floor with a three (3) foot clearance from

walls or rails. Do not use on or under balconies.

• NEVER attempt to light burner with lid closed. A

buildup of non-ignited gas inside a closed grill is hazardous.

• Never operate grill with LP cylinder out of correct

position specified in assembly instructions.

• Always close LP cylinder valve and remove

coupling nut before moving LPcylinder from specified operation position.

• Putting out grease fires by closing the lid is not possible. Grills are well ventilated for safety reasons.

• Do not use water on a grease fire. Personal injury may result. If a grease fire develops, turn knobs and LP

cylinder off.

• Do not leave grill unattended while preheating or burning off food residue on HI. If grill has not been regularly cleaned, a grease fire can occur that may

damage the product.

Ignitor Lighting the Grill

1.Open lid during lighting.

2. Open LPcylinder valve or natural gas valve.

3. Push any burner control knob in and turn the knob to the left to "HI" position. You will hear a clicking sound from all the

burners. Keep pressing the knob until the burner is lit.

4. If ignition does not occur in 5 seconds, turn the burner control off, wait 5 minutes for gas to clear away, and repeat

step 3.

5. To light other burners, repeat step 3.

NOTE: If ignitor does not work, follow Match Lighting

instructions.

Turn controls and gas source or tank OFF when

not in use.

Burner Flame Check

•Remove cooking grates and heat diffusers. Light burners, rotate knobs from HIGH to LOW. You should see a smaller

flame in LOW position than seen on HIGH. Perform burner flame check on side burner, also. Always check flame prior to

each use.

Turning Grill Off

•Turn all knobs to position. Turn LPcylinder off by turning hand-wheel clockwise to a full stop.

Ignitor Check

If ignition does not occur in 5 seconds, turn the burner control off, wait 5 minutes, and repeat the lighting

procedure. DO NOT leave burner control knob in ON position if burner does not light. If the burner does not

ignite with the valve open, gas will continue to flow out of the burner and could accidently ignite with risk of

injury.

Match-Lighting

sl_ Do not lean over grill while lighting.

1. Open lid during lighting.

2. Place match into match holder (hanging from side of cart). Light match, place into the firebox.

3. Push in and turn right knob to HIGH position. Be sure burner lights and stays lit.

4. Light other burners by pushing knob in and turning to HI position.

•Turn gas off at LP cylinder. Pushthe control knob in and turn the knob to the left to "HI" position." Clicking" should be

heard and spark seen each time between collector box or burner and electrode. See "Troubleshooting" if no click or spark.

Valve Check

•Important: Make sure gas is off at LPcylinder before checking valves. Knobs lock in OFF position. To check

valves, first push in knobs and release, knobs should spring

back. If knobs do not spring back, replace valve assembly before using grill. Turn knobs to LOW position then turn back

to OFF position. Valves should turn smoothly.

Hose Check

•Before each use, check to see if hoses are cut or worn. Replace damaged hoses before using grill. Use only identical

replacement part valve/hose/regulator as specified in the Parts List of this Use and Care Guide.

General Grill Cleaning

•Do not mistake brown or black accumulation of grease and smoke for paint. Interiors of gas grills are not painted at the

factory (and should never be painted). Apply a strong solution of detergent and water or use a grill cleaner with scrub brush on insides of grill lid and bottom. Rinse and allow

to completely air dry. Do not apply a caustic grill/oven cleaner to painted surfaces.

• Plastic parts: Wash with warm soapy water and wipe dry.

Donotusecitrisol,abrasivecleaners,degreasersora concentratedgrillcleaneronplasticparts.Damagetoand

failureofpartscanresult.

•Porcelainsurfaces:Becauseofglass-likecomposition,most residuecanbewipedawaywithbakingsoda/watersolution

orspeciallyformulatedcleaner.Usenonabrasivescouring

powderforstubbornstains.

•Paintedsurfaces:Washwithmilddetergentornonabrasive

cleanerandwarmsoapywater.Wipedrywitha soft

nonabrasivecloth.

•Stainlesssteelsurfaces:Tomaintainyourgrill'shighquality

appearance,washwithmilddetergentandwarmsoapy waterandwipedrywitha softclothaftereachuse.Baked-

ongreasedepositsmayrequiretheuseofanabrasiveplastic cleaningpad.Useonlyindirectionofbrushedfinishtoavoid

damage.Donotuseabrasivepadonareaswithgraphics.

•Cookingsurfaces:Ifa bristlebrushisusedtocleananyof

thegrillcookingsurfaces,ensurenoloosebristlesremainon cookingsurfacespriortogrilling.Itisnotrecommendedto

cleancookingsurfaceswhilegrillishot.

StoringYourGrill

•Cleancookinggrates.

•Storeindrylocation.

•WhenLPcylinderisconnectedtogrill,storeoutdoorsina wellventilatedspaceandoutofreachofchildren.

•Covergrillif storedoutdoors.Choosefroma varietyofgrill coversofferedbymanufacturer.

•StoregrillindoorsONLYifLPcylinderisturnedoffand disconnected,removedfromgrillandstoredoutdoors.

•Whenremovinggrillfromstorage,follow"CleaningtheBurner Assembly"instructionsbeforestartinggrill.

CleaningtheBurnerAssembly Followtheseinstructionstocleanand/orreplacepartsof

burnerassemblyorif youhavetroubleignitinggrill.

1.TurngasoffatcontrolknobsandLPcylinder.

2.Removecookinggratesandheatdiffusers.

3.Removecotterpinsfromrearofburners.

4. Carefully lift each burner up and away from valve openings.

SPIDER ALERT!

If you notice that your grill is getting hard to light or that The flame isn't as strong as it should be, fake the time to

check and clean the burner tubes.

Spiders or small insects have been known to create "flashback" problems. The spiders spin webs, build nests

and lay eggs in the grill's burner tubes obstructing the flow of gas to the burner. The backed-up gas can ignite

in the burner tube behind the control panel. This is known as a flashback and it can damage your grill and even

cause injury.

To prevent flashbacks and ensure good performance the burner and burner tube assembly should be removed

from the grill and cleaned before use whenever the grill has been idle for an extended period.

We suggest three ways to clean the burner tubes. Use the one easiest for you.

(A) Bend a stiff wire (a light weight coat hanger works well) into a small hook. Run the hook through each burner

tube several times.

(B) Use a narrow bottle brush with a flexible handle (do not use a brass wire brush), run the brush through each

burner tube several times.

the burner tube and out the burner ports. Check each

port to make sure air comes out each hole.

5. Wire brush entire outer surface of burner to remove food

residue and dirt.

6. Clean any blocked ports with a stiff wire such as an open

paper clip.

7. Check burner for damage, due to normal wear and corrosion

some holes may become enlarged. If any large cracks or

holes are found replace burner.

_ii_i_i_iil;_iil;iiil;iiil;i'_il;iiiiil;iiiillI;¸¸II;IIIIII;¸III;'_¸'_....

Correct burner-to-valve engagement

Indirect Cooking Poultry and large cuts of meat cook slowly to perfection on the

grill by indirect heat. Place food over unlit burner(s); the heat from lit burners circulates gently throughout the grill, cooking

meat or poultry without the touch of a direct flame. This method greatly reduces flare-ups when cooking extra fatty

cuts because there is no direct flame to ignite the fats and juices that drip during cooking.

Indirect Cooking Instructions

• Always cook with the lid closed.

• Due to weather conditions, cooking times may vary. During cold and windy conditions the temperature setting may need to be increased to insure sufficient cooking

temperatures.

• Place food over unlit burner(s)

Food Safety

Food safety is a very important part of enjoying the outdoor cooking experience. To keep food safe from harmful bacteria, follow these four basic steps:

Clean: Wash hands, utensils, and surfaces with hot soapy water before and after handling raw meat and poultry.

Separate: Separate raw meats and poultry from ready-to-eat foods to avoid cross contamination. Use a clean platter and

utensils when removing cooked foods.

Cook: Cook meat and poultry thoroughly to kill bacteria. Use a thermometer to ensure proper internal food temperatures.

Chill: Refrigerate prepared foods and leftovers promptly.

For more information call: USDA Meat and Poultry Hotline at 1-800-535-4555 (In Washington, DC (202) 720-3333, 10:00

am-4:00 pm EST).

How To Tell If Meat Is Grilled Thoroughly

• Meat and poultry cooked on a grill often browns very fast on the outside. Use a meat thermometer to be sure food has

reached a safe internal temperature, and cut into food to check for visual signs of doneness.

• Whole poultry should reach 180 ° F; breasts, 170 ° F. Juices should run clear and flesh should not be pink.

• Hamburgers made of any ground meat or poultry should reach 160 ° F, and be brown in the middle with no pink juices.

Beef, veal and lamb steaks, roasts and chops can be cooked to 145°F. All cuts of pork should reach 160 ° F.

• NEVER partially grill meat or poultry and finish cooking later. Cook food completely to destroy harmful bacteria.

• When reheating takeout foods or fully cooked meats like hot dogs, grill to 165° F, or until steaming hot.

1Burner Cooking Cook with direct or indirect heat.

Best for smaller meals or foods. Consumes less fuel.

WARNING: To ensure that it is safe to eat, food must be cooked to the minimum internal temperatures listed in the table

below.

USDA _ Recommended Safe Minimum Internal Temperatures

Beef, Veal, Lamb and Pork - Whole Cuts_ 145° F Fish 145° F

Beef, Veal, Lamb and Pork - Ground 160° F Egg Dishes 160° F

Turkey, Chicken & Duck - Whole, Pieces & Ground 165° F

United States Department of Agriculture

_AIIow meat to rest three minutes before carving or consuming.

GasRequirements LPGas

IfyourgrillisforLPGas,theregulatorsuppliedissetfor an11-in.watercolumn(WC)andisforusewithLPgas

only.Thefactory-suppliedregulatorandhosemustbe usedwitha20-lb.LPgastank.

ExcessFlowControlandLowHeat Thepropaneregulatorassemblyincorporatesanexcess

flowdevicedesignedtosupplythegrillwithsufficientgas flowundernormalconditionsyetcontrolexcessgasflow.

Rapidchangesinpressurecantriggertheexcessflow deviceprovidingalowflameandlowtemperature.Ifthe

tankvalveisturnedopentoallowgasflowwhilea burner valveisopen,thesurgeofpressurewillcausethedevice

toactivate.Thedevicewillremaincloseduntilthe pressureisequalized.Thisshouldoccurwithin5

seconds. To ensure this does not cause difficulty in lighting the grill,

follow these instructions:

1. Make sure all burner valves are "OFF".

2. Open the tank valve and wait 5 seconds.

3. Light the burners one at a time following the lighting instructions.

Care and Maintenance Time Table Chart

Frequency Based

Grill Item Painted surface

Stainless surface

All grates

Stainless grates

Porcelain grates

Burner heat tents Burners

Burner box interior

on Normal Use

Twice yearly Twice yearly

After each use

15 days

30 days 90 days

120 days

CALIFORNIA PROPOSITION 65

Cleaning Method Car wax

Stainless cleaner Burn off and wipe

Wire brush/ Dishwasher safe

Scrub pad soapy water/Dishwasher

safe Wire brush

Wire brush

Interior grill cleaning products (available at

sears)

Helpful Care and Maintenance Hints

Before grilling, pre-heat grill for 15 minutes on "HI" with hood down. To avoid uncontrolled flare-ups or grease fires, grill meats with hood open. Close hood if meats are

thick or weather is cold, or if you are using a rotisserie or indirect cooking.

Always protect your hand with a pot holder or cooking glove when coming into contact with a hot surface.

Hood up when grilling meats, especially chicken. Hood down when indirect or rotisserie cooking.

NEVER leave your grill unattended while cooking.

After use, close hood, turn burners to HI for 15 min. for self-cleaning, grease burn off.

1. Combustion by-products produced when using this product contain chemicals known to State of

California to cause cancer, birth defects and other reproductive harm.

2. This product contains chemicals, including lead and lead compounds, known to State of

California to cause cancer, birth defects or other reproductive harm.

Wash your hands after using this product.

Part list detail with graphic:

No QTY Description Picture

Bottom Panel Assembly

Caster

Caster With Lock

i i

Cart Left Side Panel Assembly

Cart Right Side Panel Assembly

Cart Rear Panel

Cart Beam

Triangle Strengthening Wedge

Drip Tray Left Bracket

Drip Tray Right Bracket

Door Assembly

Door Handle Assembly

Hood Handle Assembly

Hood Handle Bezel

iii,,_,,_I,

Grill Head

Regulator Hose Clip

Side Shelf Left Support

Side Shelf Right Support

Left Side Shelf Assembly

Right Side Shelf Assembly

8o 90 ° 80 °

Control Knob

Electronic Igniter Box

Flame Tamer

Cast Iron Cooking Grate

Warming Rack

Drip tray Assembly

Drip Cup

Hardware Pack

Hardware list:

AA. M6_12 Screw QTY."54 pcs

BB. M6 Washer

QTY: 17 pcs

CC.M6 Stretchy Washer

DD. M5_40 Screw

QTY: 2pcs

EE.Washer

18_6.4_1.5, QTY: 4 pcs

QTY: 25 pcs

ili!!i!Jiiii[ i!i!ii!iiilii

FF. M6_30 Screw

QTY: 2 pcs

GG. Shoulder screw QTY:4 pcs

HH. M6_5 Nut

QTY: 4 pcs

II. AA Battery

QTY:I pcs

If you are missing hardware or have damaged parts after unpacking grill, call 1-800-482-0131 for replacement. To order replacement parts after using grill, call 1-800-4-MY-HOME®

' /

',\

_. • ¸....I

NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from those on your particular grill model. However, the method of assembly remains the same

Product parts list:

No Description

1 Hood Rotation Shaft

2 Hood Assembly

Hood handle bezel

4 Hood Handle Assembly

5 Thermometer 6 Hood Plastic Cushion

Cast iron Cooking

Grate

8 Flame Tamer

9 R Pin

10 Main Burner

11 Main Burner Ignition Pin 12 Warming Rack

13 Grill Head

14 Heat shield

Main Gas Tube& Valve

Assembly

16 Control Panel 17 Control Knob Bezel

18 Control Knob

19 Regulator

20 Micro Switch Cable

21 Ignition Wire Long 22 Ignition Wire short

23 Spring Latch

24 Door Handle Assembly

Part. No.

CH3017302

CH3017381

CH3017382 CH3017383

CH3017304 CH3017306

CH3017384

CH3017318

CH3017311

CH30173114

CH3017313 CH3017385

CH3017386 CH3017387

CH3017388

CH3017389

CH3017351 CH3017353

CH3017390

CH3017391 CH3017392

CH3017393

CH3017394

CH3017395

QTY

1 1

2 2

1 1

2 2

29 3O

32 33

42 43 44

45 46 47

Description

Door Assembly Puerta Cart (Left) Side Panel

Assembly

Triangle Strengthening Wedge Caster With Lock

Caster (Without Lock) Ignition Pin Assembly

Drip Tray Assembly Drip Cup

Drip Tray Left Bracket Drip Tray Right Bracket Electronic Igniter Box

Cart Right Side Panel

Assembly

Cart Rear Panel Door Beam(Cart Beam)

Magnet Bottom Panel

Regulator Hose Clip Cylinder (Lock) Screw

Weight Side Shelf Left Support Side Shelf Right

Support Screw

Side Shelf Top Panel

Assembly

Side Shelf Fascia

Assembly

Part. No.

CH3017396

CH3017397

CH3017365 CH3017372

CH3017373 CH3017378

CH3017398 CH3017364

CH3017399

CH30173100

CH30173101

CH30173102 CH30173103

CH30173104 CH30173105

CH30173106 CH30173107

CH3017377

CH30173108 CH30173109

CH30173110

CH30173111

CH30173112

CH30173113

QTY

1 1

2 2

1 1

Part Diagram

j .......................................................

+ 42 hidden pages