Kenmore 415162320 Owner’s Manual
Assembly Rnstructions/Use and Care Manual
Liquid PropaneGasGrill
Model No.415.t62320
This Grill _sFor
Outdoor Use Only
®
ASSEMBLY
* Read this manua_ before cooking on
gril. FaiJure to follow aH
manufacturer's instructions could
resumt in fire or expmosion which could
cause property damage, persona_
injury or death.
oCombustion by-products produced
when using this product contain
chemicams known to the State of
California to cause cancer, birth
defects, or other reproductive harm.
Read and follow aH Safety
Statements, Assembly hstructions
and Use & Care Directions before
attempting to assemble and cook.
Some parts may contain sharp edges,
6
ob
6
especially as noted in these
instructions. Wear protective g_oves
if necessary.
* Parts
oAssemMy
, Safety Rumes
Assembmy Questions?
Call 1-800-241W548
Parts Ordering:
Call 1-800-4-MY-HOME ®
To mnstaHedAssembmer: Leave
these instructions with
consumer.
To Consumer: Keep this
manuam for future reference.
oUse and Care
* Troubmeshooting
, Espa_o_, p. 33
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
@2005Sears,RoebuckandCo,,AllRightsReserved
Printedin USA
FOR YOUR SAFETY
1. Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
2. An LP tank not connected for use shah
not be stored in the vicinity of this or any
other appliance.
FOR YOUR SAFETY
mfyou smetl gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. if odor continues, immediately call your
gas supplier or your fire department.
Safety Symbols
The symbolsand boxes shown below explain what each heading
means, Read andfollow all of the messages found throughout
the manual,
DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious iniury,
WARNING: Be alert to the possibility ofserious bodily iniury
if the instructions are not followed, Be sureto read and
carefully follow all of the messages,
CAUTmON
Call Grill Service Center For Help And Parts
If you havequestions or need assistance during assembly,
please caEI1o800o241o7548,Youwill be speaking to a
representative ofthe grill manufacturer and nota Sears
employee, Toorder new parts call Sears at Io800o4oMyoNOME®,
Product Record
iMPORTANT:Fillouttheproductrecordinformationbelow.
Model Number
Serial Number
See ratinglabelongrillforserialnumber,
Date Purchased
Ill CAUTmON
CAUTION: Indicatesa potentially hazardous situation which,
if not avoided, may result in minoror moderate iniury,
Installation Safety Precautions
• Usegrill only with LP (propane) gas and the regulator/valve
assembly supplied,
Gril! installation must conformwith localcodes, or in their
absence with National Fuel Gas Code, NFPA 54 / ANSI
Z223.1, Handlingand storage of LP cylinders must conform to
LP Gas Code NFPNANS_ 58. Grill is not for use in or on
recreational vehicles and/or boats,
All electrical accessories (such as rotisserie) must be
electrically grounded in accordancewith local codes, or
National Electrical Code, ANSI / NFPA 70. Keepany
electrical cords and/orfuel supply hoses away from any hot
surfaces,
, This grill is safety certifiedfor outdoor use in the United States
only, Do not modify for use in any other location, Modification
will result in a safety hazard,
For residential use only, Do not use for commercial
cooking.
2_463363506
Repair Protection Agreements
Congratulations on making a sma,,tpurc,Sase,Yournew
Kenmore®product is designed and manufactured for years of
dependable operation. But like all products, it may require repair
from time to time. That's when having a Repair Protection
Agreement can save you money and aggravation.
Purc,_asea Repair ProtectionAgreement now and protect
yourself from unexpectedhassle and expense,
Here's what's included in the Agreement:
[] Expert service by our 12,000 professional repair specialists
[] UnJimited service and no charge for parts and labor on all
covered repairs
[] Product repJacement if your covered product can't be fixed
[] Discount of 10%from regular price of service and service*
related parts not covered by the agreement; also, 10% off
regular price of preventive maintenance check
[] Fast help by phone- phone support from a Sears
technician on products requiring in-home repair,plus
convenient repair scheduling
Once you purchase the Agreement, a simple phone call is all that
it takes for you to schedule service. You can call anytime day or
night, or schedule a service appointment online.
Sears has over 12,000 professional repair specialists, who have
access to over 4.5 million quality parts and accessories. That's
the kind of professionalism you can count on to help prolong the
life of your new purchase for years to come. Purchase your
Repair Protection Agreement today!
Some limitations and exclusions apply.
For prices and additional information call 1o800o827o6655.
Sears Installation Service
KENMORE GRILL WARRANTY
One Year Full Warranty on Kenmore Grill
If this grill is defective in material or workmanship within one
year from the date of purchase, call 1-800-4-MY HOME®to
have it repaired free of charge.
Additional Limited Warranty on Specific Grill Parts
Forthe time periods listed below, the following specific grill
parts will be replacedfree of charge if they are defective in
material or workmanship. You will be charged for labor.
Lifetimeon Aluminum Top and Bottom Castings.
Two years from purchase date on Stainless Burner
Assembly.
All warranty coverage excludes batteries and any grill part
paint loss or rusting,which are either expendable parts that
can wear outfrom normaluse in less than a year, or are
conditions that can be the result of normal use, accident or
improper maintenance.
AI! warranty coverage is void if this grill is used for
commercial or rental purposes.
This warranty gives you specific lega!rights, and you may
also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA,
Hoffman Estates, tL 60179
For Sears professional installation of home appliances, garage
door openers, water heaters, and other major home items, in the
U.S.A. call 1-800-4-MY-HOME®
463363506,3
• NEVER store a spare LP tank under or near gdli or in
enclosed areas
Never fiH the cylinder beyond 80% full.
An overfilled or improperly stored tank is a hazard due
to possible gas release from the safety relief vane.
This could cause an intense fire with risk of property
damage, serious injury or death.
LP Tank
The LP tank used with your grill must meet the following
requirements:
Use LP tanks only with these required measurements: 12"
(30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 Ib. (9 kg.)
capacity maximum.
LP tanks must be constructed and marked in accordance with
specifications for LP tank of the U.S. Department of
Transportation (DOT). See LP tank collar for marking.
LP tank valve must have:
, Type I outlet compatible with
regulatoror grill.
Safetyrelief valve.
ULlisted Overfill Protection
OPDHand Wheel
Device (OPD). This OPDsafety
feature is identified by a unique triangular hand wheel. Use
only LP tanks equipped with this type of valve.
, LP tank must be arranged for vapor withdrawal and include
collar to protect LP tank valve.
• tf you see, smell or hear escaping gas, immediately get
away from the LPtank/grill and call your fire
department.
LP Tank Removal, Transport And Storage
Turn OFF all control knobs and LP tank valve.Turn coupling
nut counterclockwise by hand only - do not use tools to
disconnect. Lift LP tank wire upward off of LP tank collar, then
lift LP tank up and off of support bracket. Install safety cap onto
LP tank valve. Always use cap and strap supplied with valve.
Failure to use safety cap as directed may result in serious
personal injury and/or property damage.
LPTankValve
SafetyCap
LP (Liquefied Petroleum Gas)
• LP gas is nontoxic, odorless and colorless when produced. For
Your Safety, LP gas has been given an odor (similar to rotten
cabbage) so that it can be smelled.
LP gas is highlyflammable and may ignite unexpectedly when
mixed with air.
LP Tank Filling
Useonly licensed and experienced dealers.
• LP dealer must purge tank beforefilling.
• Dealer should NEVERfill LP tank more than 80% of LP tank
volume. Volume of propane in tank will vary by temperature.
• A frosty regulator indicates gas overfil!. Immediatelyclose LP
tank valve and call local LP gas dealer for assistance.
Do not release liquid propane (LP) gas into the atmosphere.
This is a hazardous practice.
Toremove gas from LP tank, contact an LP dealer or call a
local fire department for assistance. Check the telephone
directory under "Gas Companies"for nearest certified LP
dealers.
Retainer Strap
A disconnected LP tank in storage or being transported must
have a safety cap installed (as shown). Do not store an LP tank
in enclosed spaces such as a carport, garage, porch, covered
patio or other building. Never leavean LP tank inside a vehicle
which may become overheated by the sun.
, Do not store an LP tank in an area where children play.
4,463363506
LP Tank Exchange
Connecting Regulator To The LP Tank
, Many retailers that sell grills offer you the option of replacing
your empty LPtank through an exchange service, Useonly
those reputable exchange companies that inspect, precision fill,
test and certify their cylinders. Exchange your tank onJy for
an OPD safety feature-equipped tank as described in the
"LP Tank" section of this manual.
Always keep newand exchanged LP tanks in upright position
during use, transit or storage.
. Leak test new and exchanged LP tanks BEFORE
connecting to grit1.
LP Tank Leak Test
For your safety
Leak test must be repeated each time LP tank is exchanged or
refilled.
Do not smoke during leak test.
• Do not use an open flame to check for gas leaks.
Grill must be leak tested outdoors in a well*ventilated area,
away from ignition sources such as gas fired or electrical
appliances. During leak test, keep grill away from open flames
or sparks.
. Usea dean paintbrush and a 50/50 mild soap and water
solution. Brush soapy solution onto areas indicated by arrows
in figure below. Leaks are indicated by growing bubbles.
1, LP tank must be properly secured onto grill. (Refer to
assembly section.)
2. Turnall control knobs to the OFF position.
3. Turn LP tank OFF by turning OPD hand wheel clockwise to a
full stop.
4. Remove the protective cap from LP tank valve. Always use
cap and strap supplied with valve.
'_----_---- OPDHandWheel
Type1outlet with
threadon outside
SafetyReliefValve
Strapand Cap
Do not use a POL transport plug
(plastic part with external threads)!
It will defeat the safety feature of
the valve.
If "growing" bubbles appear do not use or move the LP tank.
Contact an LP gas supplier or your fire department!
A Do not use household cleaning agents. Damageto gas
train components can result.
5. Hold regulator and insert nipple into LP
tank valve. Hand-tightenthe coupling
nut, holding regulator in a straight line
with LPtank valve so as not to cross*
thread the connection.
Nipple has to be centered
into the LP tank valve.
463363506.5
Holdcoupling nut and regulator
asshown for proper connection
to LP tank valve.
Leak Testing Valves, Hose and Regulator
1, TurnaHgrilJcontrol knobs to OFF.
,
Be sure regulator istightly connected to LP tank.
3.
Completely open LP tank valve by turning OPD hand wheel
counterclockwise, if you hear a rushing sound, turn gas off
immediately.There is a major leak at the connection. Correct
before proceeding by calling Sears for replacement parts at
1-800-4-MY-HOME®.
4, Brush soapy solution onto areas where bubbles are shown in
picture below:
A Neverremovethreaded
orifice atend of valve.
6. Turnthe coupling nut clockwise and tighten to a full stop. The
regulatorwill seal on the back*checkfeature in the LP tank
valve, resulting in some resistance. An additional one-half to
three-quarters turn is required to complete the
connection. Tighten by hand only - do not use tools.
NOTE:
if you cannot complete the connection, disconnect regulator and
repeat steps 5 and 6. if you are still unable to complete the
connection, do not use this regulator!
. Donot insert any tool or foreign obiects into the valve outlet
or safety reliefvalve. You may damage the valve and cause
a leak. Leaking propane may result in explosion, fire, severe
personal injury,or death..
If a leak isdetected at any time, STOPand call the fire
department.
If you cannot stop a gas leak, immediatety dose LPtank
valve and call LP gas supplier or yourfire department!
\
5. If "growing" bubblesappear, there is a leak. Close LP tank
valve immediately and retighten connections. If leaks cannot
be stopped do not try to repair. Call Searsfor replacement
parts at 1-800-4-MY-HOME®,
6. Always close LPtank valve after performing leak test by
turning hand wheel clockwise.
. Never attempt to attach this grill to the self-contained LP gas
system of a camper trailer or motor home.
. Donot use grill until leak-tested.
6,463363506
For Safe Use Of Your Grill And To Avoid Serious
Injury:
Donot letchildren operate or play near grill.
Keep grill area clear and free from materials that burn.
Donot block holes in bottom or back of grill.
Check burnerflames regularly.
Use grill only in well*ventilated space. NEVER use in
enclosed space such as carport, garage, porch, covered
patio, or under an overhead structure of any kind.
Donot usecharcoal or ceramic briquets in a gas grill.
(Unlessbriquets are supplied wib your gn_tt,)
Use grill at Jeast 3 ft. from any wall or surface. Maintain
10ft. clearance toobjects that can catch fire or sources of
ignitionsuch as pilot lights on water heaters, live electrical
appliances, etc.
Safety Tips
,& Beforeopening LP tank valve, check the coupling nut for
tightness.
,& When grill is not in use, turn offall control knobs and LP tank
valve.
,& Never move grill while in operation or still hot.
,& Use long*handled barbecue utensils and oven mittsto avoid
burnsand splatters.
,& Maximum load for shelves is 10 Ibs.
,& The grease cup must beattached to grease tray and emptied
after each use. Do not remove grease cup until grill has
completely cooled.
,& If you notice grease or other hot material dripping from grill
onto valve, hose or regulator, turn off gas supply at once.
Determinethe cause, correct it, then dean and inspect valve,
hoseand regulator before continuing. Perform a leaktest.
,& The regulator may make a humming or whistling noiseduring
operation. This will not affect safety or use of grill.
,& If you have a grill problem see the "TroubleshootingSection".
• Apartment Dwellers:
Checkwith management to learn the requirements and fire
codes for using an LP gas grill in your apartment complex. If
al!owed, use outside on the ground floor with a three (3) foot
clearance from walls or rails. Do not use on or under
balconies.
• NEVERattempt to light burner with lid closed. A buildup
of non-ignited gas inside a closed grill is hazardous.
Never operate grill with LP tank out of correct position
specified in assembly instructions.
Always close LPtank valve and remove coupling nut
before moving LP tank from specified operation
position.
If the regulator frosts, turn off grill and LP tank valve
immediately. This indicates a problem with the tank and it
should not be used on any product. Return to supplier!
463363506,7
• Do not Jeavegrill unattended while preheating or
burning off food residue on high. If grill has not been
reguJafiy deaned, a grease fire can occur that may
damage the product. Follow instructions on General
Grill Cleaning and Cleaning The Burner Assembly to
prevent grease fires.
Ignitor Lighting
,& Do not lean over grill while lighting.
Match°Lighting
,& Do not lean over grill while lighting.
1, Open lid. Turnon gas at LP tank,
2. Place lit match into match lighting hole from outside of grill
bottom (as shown),
3. Push in and turn right knob to_ preheat position, Be sure
burner lights and stays lit,
4. Light left burner by pushing left knob in and turning to
preheat position.
After Lighting: Turn knobs to HI for warm-up.
1. Open lid. Turnon gas at LP tank.
2. Turn left knob to _ preheat to light.
3. Push ignitor button rapidly (up to 5 times) to light.Be sure
burner lights and stays lit.
4, if burner does not light, turn knobs to OFF, wait 5 minutes, try
again.
5. Once left burner is lit, turn right knob to _ preheat to light.
6. if ignitordoes not work, wait 5 minutes, then follow match
lighting instructions.
After Lighting: Turn knobs to HIGH position for warm-up. Do
notwarm up grill with knobs in _ preheat position. Knobs and
handle will become uncomfortably hot if left in preheat
position.
CAUTmON
If burner does not light, turn knobs to OFF,wait 5
minutes, and try again. Always close valve during the 5
minute waiting period. If the burner does not ignite with
the valve open, gas will continue to flow out of the burner
and could accidentally ignite with risk of injury.
y Matchlightinghole
Hose Check
• Beforeeach use, check to see if hoses are cut, worn or kinked.
Replace damaged hoses before using grill. Use only
valve/hose/regulator specified in the Parts List.
Normal Kinked
Hose Hose
Before Your First Cookout
. Light burners, check to make sure they are lit, dose the lid and
warm up grill on HIGH for 15 minutes. This curing of paint and
parts will produce an odor only on first lighting.
Burner Flame Check
, Light burner, rotate knobs from HI to LO, Youshould see a
smaller flame in LO position than seen on HI, Always check
flame prior to each use, If only lowflame is seen refer to
"Sudden drop or low flame" in the TroubteshootingSection,
8,463363506
Turning Grill Off
. Turn all knobs to OFF position. Turn LP tank off by turning
OPD hand wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP tank. Pressand hold ignitor button. "Click"
should be heard and spark seen each time between collector
box or burner and electrodes. See "Troubleshooting"if no click
or spark.
Valve Check
• Important: Make sure gas is off at LP tank before checking
valves. Knobslock in OFF position. Tocheck valves, first
push in knobs and release, knobs should spring back. If knobs
do not spring back, replace valve assembly before using grill.
Turn knobs to LO position then turn back to OFF position.
Valves should turn smoothly.
General Grill Cleaning
. Keep the outside of your grill looking new by cleaning it once a
month with warm soap and water or a non-abrasive cleaner. If
you don't havea grill cover, wipe off dust and grime before
starting your grill.
. Coating the cooking grids with spray-on cooking oil will keep the
food from sticking and make clean up easier.After cooking,
scrape the grates with a long handled, brass wire bristle brush.
Repainting Your Grill
. After extended useand exposure to weather, paint on grill may
deteriorate or become spotted. Although this detracts from
grill's appearance, it will not impair its performance.
Torefinish your grill brushoutside of gril! lid and bottom with
wire brush and lightly sand with fine grit sandpaper. Sanding
allows new paint to adhere moreeasily. Wash grill lid and
bottom with soap and water to remove dust and grease. Do not
use a grill cleaner on outside of grill. Wipe with vinegar.
Refinishoutside with heat-resistant paint. Do not paint inside
of grill.
NATURAL HAZARD ,, SPmDI=R$
FACT: Sometimesspiders and other small insects climb into
the burner tubes attached to the burners. The spiders spin
webs, build nests and lay eggs. Thewebs or nests can be
very small, but they are very strong and can block the flow of
gas. Clean burners prior to useafter storing, at the beginning
of grilling season or after a period of one month not being
used.
. Check inside the grill bottom for grease build up and clean
often, especially afLercookingfatty meat.
. Do not mistake brown or black accumulation of grease and
smoke for paint. Interiorsof gas grills are not painted at the
factory (and should never be painted). Apply a strong solution
of detergent and water or usea gril!cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry. Do not apply a caustic grill/oven cleaner to painted
surfaces.
• Plated wire grates: Washgrates and V-bar with concentrated
gril! cleaner or use soap and water solution. Dry thoroughly and
store indoors between cookouts.
. PJastic parts: Wash with warm soapy water and wipe dry.
A Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
• Porcelain grates: Becauseof glass*like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use non-abrasive scouring
powder for stubborn stains.
Typical spider webs inside burner.
Spider guards are on the air intakes in an effort to reduce this
problem, but itwill not eliminate it! An obstruction can result
in a "flashback" (afire in the burner tubes). The gril! may still
light, but the obstruction does notallow full gas flow to the
burners.
IF YOU EXPERIENCE THE FOLLOWING:
1. Smell gas.
2. Burner(s) will not light.
3. A small yellow flame from burner (should be blue).
4. Firecoming from around or behind control knob.
STOP!
Immediately turn off gas at LPtank!
,A After a burner tube fire, you must inspect the hose and
do a"Leak Test" to assure no damage has occured to
the parts.
SOLUTION:
Wait for grill to cool.
Follow the "Cleaning The BumerAssembly" instructions.
Clean burnersoften. Use a 12" pipe cleaner to dean out the
burner tubes. You may also force a stream of water from a
hose nozzle through burner tubes to dean them.
4¢3363506.9
C_eaning The Burner Assembly
Follow these instructions to dean and/or replace parts of burner
assemNy or if you have trouNe igniting the grill,
1, Turn gas off at control knobs and LP tank.
2, Removecooking grids and vaporizer tents,
3, Removetwo pal nuts, carry-over tube and burners,
4, Undergrill remove grease pan and tray, Qean with soap and water,
5, Underconsole disengage ignitor wire,
6, Wipe ceramic electrode with rubbing alcohol and cloth,
7, Qean carry-over tube and burners exterior with soap and water, Lay
burners on fiat surface, insert garden hose (preferaNy with nozzle),
into burner tubes forcing water through tubes, Make sure water
comes out of every porthole, Open dogged portholeswith a thin
wire, Shake out excess water and examine porthole, Dueto
normalwear and corrosion some portholes may become enlarged,
if so replace burner, If any horizontal cracks appear from porthole to
porthole or large holes (other than portholes) are found replace
burner,
8, Ifgri!l is to be stored, coat burners lightly with cooking oil, Wrap in
protective cover to keep insects out, If not storing use following
steps,
VERY IMPORTANT:
Burner tubes must engage valve openings as shown (A). Do not
leave separated as shown in Figure B.
9, Attach ignitor wire to electrode,
10, Repositioncooking grids and vaporizer tents, Place clean grease
tray and pan intogrill bottom,
11, Before cooking again on grill, perform a "Leak Test"and "Burner
Flame Check",
,& Do not use ceramic briquets or charcoal in your grill,
Cleaning the Grease Tray
Your grill is equipped with a removaNe grease tray,Although grease
will drain from the grease tray to the grease cup provided, food particles
and debris may accumulate in the bottom and should be removed after
cooking 5 to 10times, This can easily be done bysliding the grease tray
out of the rear of the unit, Make sure in replacingthe tray to push it all the
way forward,
Correctly assembledburner tube and valve.
10,463363506
Storing Your Grill
, Clean cooking grates,
, Store in dry location,
, When LP tank is connected to grill, store outdoors in well-
ventilated space and out of reachof children,
, Cover grill if stored outdoors,
, Store grill indoors ONLY if LP tank is turned off and
disconnected, removed from grill and stored outdoors,
, When removing grill from storage follow "CleaningBurner
Assembly" instructions before starting grill,
Food Safety
Food safety is a very important part of enjoying the outdoor
cooking experience, To keep food safe from harmful bacteria,
follow these four basic steps:
Ctean: Wash hands, utensils, and surfaces with hot soapy water
before and after handling raw meat and poultry,
Separate: Separate raw meats and poultry from ready*to-eat
foods to avoid cross contamination, Usea dean platter and
utensils when removing cooked foods,
Cook: Cook meat and poultry thoroughly to kill bacteria, Use a
thermometer to ensure proper internal food temperatures,
Chill: Refrigerate prepared foods and leftovers promptly,
For more information call: USDA Meat and Poultry Hotline at
1o800o535o4555in Washington, DC (202) 720-3333, 10:00 amo
4:00 pm EST.
How To Tell If Meat JsGrilled ThorougMy
• Meat and poultry cooked on a grill often browns very fast onthe
outside, Use a meat thermometer to be sure food has reached
a safe internal temperature, and cut into food to check for
visual signs of doneness,
• Whole poultry should reach 180° F; breasts, 170° F,Juices
should run dear and flesh should not be pink,
• Hamburgersmade of any ground meat or poultry should reach
160° F,and be brown in the middle with no pinkiuices, Beef,
veal and lamb steaks, roasts and chops can be cooked to 145°
F,All cuts of pork should reach 160° R
• NEVER partially gri!l meat or poultry and finish cooking later,
Cook food completely to destroy harmful bacteria,
• When reheating takeout foods or fully cooked meats like hot
dogs, grill to 165° F,or until steaming hot,
4633¢3506.11
Key_
1
Description Part#
2
LegAssembly................... 7000621
26
Description Part#
1
GroundWire Connector........... 7000360
2
3
4
5
6
7
8
9
10
11
12
13
1
BottomShelf.................... 7000612
25
#10-16xl/2' Self-TapScrew ........ 7000999STD611005
2
LegExtender.................... 7000320
3
"U"Nut 1/4-20................... 7000185
1
1/4-20x6" TankThumbscrew....... 7000355
1
1/4-20FlangedHexNut........... 7000394
2
FlatWasher..................... 4080413
1
HitchPin....................... 4080062
1
AxleRod....................... 7001149
2
Wheel......................... 7000262
4
Rail........................... 7000286
HeatShield..................... 7000388
27
28
29
3O
31
32
33
34
35
36
37
38
2
Shelves........................ 7000351
TopCasting..................... 7000615
BezelTemperatureGauge......... 4157169
1
TemperatureGauge .............. 7000361
1
LogoPlateAssembly............. 4157167
2
ShoulderBolt ................... 7000186
3
ControlKnob.................... 7000312
CondimentBasket................ 7000348
Grill@Night"MHandle ............. 4154619
1
LeftLampAssembly.............. 4159060
1
RightLampAssembly............. 4159059
2
#10-24x3/4"Thumbscrew.......... 4080132
14
15
16
17
18
19
2O
21
22
23
24
25
FrontPanel..................... 7000640
PushFastener................... 4080112
GrillBottom..................... 7000844
Carry-OverTube................. 7000278
2
PalNut ........................ 7000132
2
CastingBumper................. 7000184
3
Burner......................... 7000083
4
#10-1"Self-TapScrew ............ 4080716
Electrodew/WingNut............. 7000378
ControlPanel ................... 7001354
Valve/Hose/RegulatorAssembly..... 7000335
IgnitorModule................... 7000944
39
40
41
42
43
44
45
46
47
48
49
4
Bulb,T3.25..................... 4157175
2
BulbHolder..................... 4154614
4
#8xi/2' Screw................... 4080130
C-SizeBatteries(6-pack).......... 4153238
BatteryDoor.................... 4154612
3
VaporizerTents.................. 7000045
3
CookingGrid,8"x15".............. 7000027
Button......................... 7000161
SwingAway..................... 7000182
GreaseTray .................... 7000042
GreasePan..................... 7000046
12_463363506
47
45
45
45
_4_J.f 3
3"
13
3
\
,,,,
23
3
33
49
°_3
34
10
15
463363506.13
Cart Assembly
Placebottom shelf on tableor grill shipping carton.
insert tabs on leg assembliesinto left and right sides of bottom shelf.
Attach legassemblieswith two screws (3)on each leg.
LegAssembly
3
Qty:8
Bottom Shelf
/
/
/
14_463363506
Correctlyassembledlegs
LegExtenders,AxleRod,WheelsandTankThumbscrew
Turncart upside down.
insert leg extenders. Checkto makesure leg extenderis all theway into the leg.
Attach u-nut(5}to tab. Seeenlargementof u-nut for correct position.
Threadtankthumbscrew (6)into hole and u-nut. Screwflanged hexnut (7}onto end of tank thumbscrew. Do nottighten
further.
Slidewheel on axlerod. Insertaxle rod into large bole in bottom shelf. Attach otherwheel with
Twowashers (8)and a bitch pin (9}.
5 6 _j/ Qty:1 8
Qty:1 Qty:1 7
Nottoscale Nottoscale Qty:1 Qty:2
8
\\ \
LegExtender
\
\
Wheel
flangedhexnut
Hubon wheelfaces
intogrillbottom
Stand cart upright and remove
cardboard sleeves
463363506.15
RailAssembly
Overlap rails (all identical} and hook tabs into slots. Pull rails to latch.
Attach one screw (3)in center of each rail.
Attach rail to legswith two screws in eachcorner.
HINT:
Firmly push rail down into leg notches.Attach lower screwfirst.
3
Qty:10
\
\
Rail
16,463363506
Front Panel
Position front panelbetweenfront legs.insert tabs on front panel into slots in bottom sheff.
Seeinsetbelow.
Securetop of paneRto legsusing push fasteners (15}.
Inserttabsinto slots
15
Qty:2
3
Qty:2
Front __-J
Panel
HoseHeatShield
Attach hose heatshield to right sideof cart
with two screws (3}.
Rightsideof cart _ ....
3
HeatShield
4¢3363506,17
Grill Bottom Assembly
Angle grill bottom assembly around and under therails.
Makesure ribs on each sideofbottom casting are nestled into notches on
castingseat.
Attach four screws (21}inside grill bottom and into casting seat.
Placeu-nut (5}as shown into indenton left and right side ofgrill bottom.
ent
5
Qty:2
Nottoscale
21
Qty:4
', Close up of rightside
',, of griUUbottom.
J
J
21
GrillBottom
jl
j_
18,463363506
Electrodewith Wing Nut or Nut
inside bottom casting insert electrode and attach
with wing nut or nut.
Viewof electrodeattachedandaligned
withaportholeinthe burner.
Electrode
..... WingNutOr Nut
Fingertighten only
Front
463363506,19
Console Assembly
Holdcontrol panel close to bottom casting. Feedthe
valve/hose/regulatorassembly over the front panelso that it
hangsinside thecart.
Attach short ignitor wire toelectrode.
Position valves into burner tubes (see burner-valveview). Rotate
control panelup and rest flangeover rail.
Attach control panel to legswith two screws (3}on right side,
onescrew in top hole on left side.
\
N
Be surevalves are insertedfully into tubes.
3
Qty:3
BurnerTubes
ControlPanel
Note:
Consolemayhaveunusedholes
forfeaturesinothergrillmodels.
20,463363506
Valve/Nose
RegulatorAss
Loading...