Kenmore 23352549590, 23352545590, 23352544590, 23352540590, 23352449590 Owner’s Manual

...

ood

Use & Care / installation Manual

cocina

Manual de uso y cuidado /instalaci6n

Models Modelos

233.52340590 (3o" wide - Stainless)

233.52344590 (30" wide - Bisque)

233.52345590 (3o" wide - White)

233.52349590 (30" wide - Black)

233.52440590 (36" wide - Stainless)

233.52444590 (36" wide - Bisque)

233.52445590 (36" wide - White)

233.52449590 (36" wide - Black)

233.52540590 (42" wide - Stainless)

233.52544590 (42" wide - Bisque)

233.52545590 (42" wide - White)

233.52549590 (42" wide - Black)

99043206C Sears, Roebuck and Co,, Hoffman Estates, UL60179 U,S,A, www,sears,com

SECTION ..................................................................... PAGE

Warranty .............................................................................. 2

Safety instructions ............................................................... 2

Operation ............................................................................. 3

Cleaning .............................................................................. 3

Parts included With Hood ................................................... 4

Parts Not included With Hood ............................................ 4

Tools Needed ...................................................................... 4

Equivalent Duct Length Chart ............................................ 5

Prepare The Hood Location ............................................... 6

Prepare The Hood (All installations) .................................. 7

Prepare The Hood (Ducted installations) ...................... 8, 9

Prepare The Hood (Non-Ducted installations) .......... 10, 11

Connect The Wiring .......................................................... 12

install The Hood ................................................................ 13

Service Parts ............................................................... 14, 15

A iNTENDED FOR DOMESTIC COOKING ONLY.

if within 1 year from the date of installation, any part of this range hood fails to function properly due to a defect in mate-

rial or workmanship, Sears will repair the part or furnish and install a new part, free of charge.

FULL 30-DAY WARRANTY ON FINISH ON PAINTED OR BRIGHT METAL PARTS

if within 30 days from the date of installation, the finish on any painted or bright metal parts of this range hood is defective in

material or workmanship, Sears will furnish and install a new 0art, free of charge.

WARRANTY SERVICE iS AVAILABLE BY CONTACTING THE NEAREST SEARS SEWCE CENTER/DEPARTMENT

IN THE UNITED STATES.

This warranty applies only while this product is in use in the

United States. This warranty gives you specific legal rights

and you may have other rights which vary from state to state. Sears, Roebuck and Co,, Dept 817WA, Hoffman Estates,

IL 60179

WARNING _ A

TO REDUCE THE RiSK OF FIRE, ELECTRIC SHOCK, OR iNJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufac- turer. If you have questions, contact the manufacturer at the address listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified person(s)in accordance with all applicable codes and standards, including fire-rated codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), and the American Society

for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

6. To reduce the risk of fire or electric shock, do not use this

range hood with an additional speed control device.

7. Ducted fans must always be vented to the outdoors.

8. To reduce the risk of fire, use only metal ductwork.

9. Use with approved cord-connection kit only.

10.This unit must be grounded.

TO REDUCE THE RiSK OF A RANGE TOP GREASE F_RE:

1. Never leave surface units unattended at high settings.

Believers cause smoking and greasy spillovers that may ignite. Neat oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when cooking flaming foods.

3. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for the size of the surface element. 2

WARNING _,

TO REDUCE THE RiSK OF iNJURY TO PERSONS iN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UPA FLAMING PAN -You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels

- a violent steam explosion will result.

4. Use an extinguisher ONLY if: A. You know you have a Class ABC extinguisher and you

already know how to operate it.

B. The fire is small and contained in the area where it

started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

* Based on "Kitchen Firesafety Tips" published by NFPA.

CAUTION A

1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction

dust, etc. off power unit.

3. For best capture of cooking impurities, your range hood

should be mounted so that the top of the hood is 24-30" above the cooking surface.

4. Use only with range hood cord-connection kits that have been investigated and found acceptable for use with this

model range hood.

5. Please read specification label on product for further information and requirements.

tf hood is to be installed Non-Ducted: o Purchase a non-ducted filter from your local

distributor or retailer and install it beneath the aluminum mesh filter.

[_ON BLOWER

['HLO _] ON UGHT

A WARNING: To reduce the risk of electric shock,

Aluminum mesh filters Clean frequently using hot water and a mild detergent or in

your dishwasher. The aluminum mesh filters should be washed approximately every month depending on the amount of us-

age. Wash more often if your cooking style generates greater grease - like frying foods or wok cooking.

disconnect from power supply before cleaning.

Speed Infinite speed slide control controls blower speed.

Slower Turns the blower "ON" and "OFF"'.

When the blower is turned "OFF", the speed control remains at the preset speed. When the b!ower is turned on again, it will

return to the previously chosen setting.

Light Turns the light "ON" and "OFF".

First position turns on both bulbs for normal lighting. Second position turns off the left side bulb. Ifyou want a night-

light feature, combine a 75 Watt bulb (on the left) and a 25 Watt bulb (on the right).

Third position turns both bulbs "OFF". Maximum bulb rating is 75 Watts. Do not install bulbs rated

higher than 75 Watts.

Non=ducted filters (Clean Cooking hoods only)

(available separately - see page 4)

Clean filter surfaces frequently with a damp cloth and a mild detergent. DO NOT immerse filters in water or put in dish-

washer. With normal hood use, replace the non-ducted filters approximately every 6 months. Replace filters more often as

hood use increases.

Painted hood surfaces Wiping regularly with mild soap/detergent and warm water

should protect painted hood surfaces. Be cautious about us- ing "New and Improved" cleaning agents. Your hood is in-

stalled over hot cooking equipment. Most chemicals found in cleaning agents react with heat to loosen paint.

Stainmess steel hood surfaces Stainless steel hoods should be washed regularly with a clean

cloth, warm water and mild soap or dish detergent. Clean in the direction of the polish lines. Rinse well with clear water

and wipe dry immediately. You may wish to apply light oil used for furniture polishing to emphasize its bright finish.

Slower assembly Blower assembly can be cleaned with a damp cloth and mild

detergent. Use care when cleaning blower wheels - they must not become bent or misaligned. DO NOTALLOW WATER TO

ENTER MOTOR= Make sure all surfaces are completely dry before re-installing filters and restoring power=

Motor is permanently lubricated. Do not oil or disassemble motor.

O_ q_

Amuminum Grease Fimters

Damper / Duct Connector (For use with 3¼" x 10" duct)

(f_) Light Bulbs

(75 W Maximum) (2 per hood)

Purchase locally.

OPTmONAL PARTS (purchase separateJy)

NonoDucted Filter Kit (Clean Cooking Fiiter)

(2 per hood) Sears Part No. 50185

Parts Bag (4 hood mounting screws inside)

Spmashpmate Sears Part Nos,

58120 30" Black/Bisque 58128 30" White/Almond

58129 30" Stainless 58130 36" Black/Bisque

58138 36" White/Almond 58139 36" Stainless

58140 42" Black/Bisque 58148 42" White/Almond

58149 42" Stainless

Cord Kit (Allows hood to be plugged into a

standard 120 VAC waII outlet)

Sears Part No. 233.22HCK44D

Ducting Accessories (See "Equivalent Duct Length Chart" on page 5 for Ducting

Accessory Model Nos.

I'Parts Not tncmuded With Hood" available by calling Sear_

at 1-800o4oMY-HOME _ !

Saw

'°le

Tape

asure

Duct

Tape

_N !/4"

utdriver

_S wire

tripper

KenmorerangehoodsaredesignedtoperformefficientlywhenattachedtoIongrunsofduct.Asapointofreference,thishood wiIIfunctionatapproximately80%ofitsratedairftowwhen200equivalentfeetof7"roundductworkisattached.Usethischart

tocalculatetheequivalent duct length of your system.

Broan Modem401

Straight Duct

3¼qn. × 10qn. x 2-ft, long

Equivalent length

2ft.

Broan Modem408

Straight Duct

8=in. round x 2-ft. long

Equivalent length

2ft°

Broan Modem407

Straight Duct

7qn. round × 2-ft° long

EquivaIent length

2ft°

6qn. Round Elbow

Broan Modem419

EquivaIent length

8 ft.

Broan Model 428

3¼-in, × 10-in,

Right-angme Embow

Equivalent length

8.5 ft.

3¼oin, × 10-in.

Right=angle Fiat Elbow

Broan _lodel 429

Equivalent Iength

24 ft.

Broan Model 430

3¼=in, × 1Oqn,

Right=angle

Short

Eave Embow

quivalent Iength

15ft.

Broan Model 431

3¼qn. × 10=in,

Right-angle

Long

Eave Elbow

quivaIent length

15 ft.

64n= Round

Wall Cap

_ Sears Modem 59691

Equivalent length

34 ft.

(6-fL w/o damper)

7=in°Round

Wall Cap

Equivalent length

Broan ModeB 847

34 ft.

(6-fL w/o damper)

Sears Modem

59391

3¼4n° ×

10-in,

WammCap

Equivalent

length

45 ft.

(7-ft= w/o damper)

_,lodel 59091

Roof Cap

(accepts 7-in° round

or 3¼qn° × !0-in, duct)

Equivalent length

30 ft. (7-ft=w/o damper)

7qn° Round Elbow

Broan Modem4!5

EquivaIent length

8 ft.

Sears Model 59581

3¼=in. × 10=in° to

6qn. Round Transition

Equivalent Iength

5.5 ft.

Broan Model 412H

3¼=in, × 10-in. to

7=in. Round

Transition

Equivalent Iength

5.5 ft.

Sears Modem"Ducting Accessories" available by calling:

Sears at 1-800=4=MY=HOME_

Broan Model "Ducting Accessories" avaHabme by calling:

1=800=558=1711°

1. Determine whether hood will discharge vertically, hori- zontally, or non-ducted.

For vertical or horizontal discharge, run ductwork between

the hood location and a roof cap or wall cap.

For best results, use a minimum number of transitions and

elbows.

2. Use these diagrams for proper placement of ductwork and electrical cutout in cabinet or wall.

For a nomducted installation, DO NOT cut a duct access hole.

ROOF CAP

3W' X 10" DUCT

(For vertical discharge)

HOUSE WIRING

or Back of hood)

CAP

3W' X 10" DUCT (For horizontal discharge)

HOOD MOUNTING SCREWS (4) VERTICAL DUCTING

1 315/16" (30" hood) 1 315/16" (30" hood)

1615/ 6" 36" hood _ _15/ ,, ....

1_ . _ ! t3 16 [_lb" nooo)

19 °/16 (42" hood) _ 1915/16" (42" hood/

l 3_A" X 10"

3. Run house wiring between service panel and hood loca- tion.

WOOD SliMS

(recessed-bottom CENTER (in cabinet bottom)

cabinets only)

t ELECTRmCAL

L|NE

ACCESS HOLE

WOOD SHIMS 3!4" X 10"

(recessed-bottom HORIZONTAL DUCTING

cabinets only)

l HORIZONTAL DUCT

CABINET- ACCESS HOLE

CAB|NET FRONT

BOTTOM -- 61A

1315/16" (30" hood)

_,..._16 5/16 ( (30"

1 915/16 '* (42" hood) 1 616/16" (36" hood)

HOOD _ 1916/16"(42"hood)

MOUNTING CENTER ELECTRmCAL

ACCESS HOLE

SCREWS (4) L|NE (inwalm)

1. Removeanddiscard:_ fromnoseofhood,

Protective Plastic from light lens, and Cardboard FHler

from bottom of hood.

Remove and set aside: Damper / Duct Connecter.

2. Remove Bottom Cover from hood. Set cover and mount- ing screws aside.

PROTECTIVE

PLASTIC --_ /

SHiPPiNG

TAPE

DAMPER/DUCT

CONNECTOR

CARDBOARD

FILLER

3. Remove Wiring Cover from hood. Set cover and mounting

screw aside.

4. Remove either top or back Wirinq Knockout and install

approved Electricam Cabme Cmam_.

BOTTOM

COVER

¢b

COVER

WiRiNG

KNOCKOUT

ELECTRICAL

CABLE CLAMP

{b q_

1. ChoosethecorrectblowerpositionforyourinstaIlation. Forverticaldischarge:MakesurethattheBmower Dis-

chargA lines up with the Duct Opening in the top of the

hood. Lift up the blower, slip the b!ower mounting rods into brackets on blower and tighten knurled nuts securely. Plug

in blower.

For horizontal discharge: Make sure that the Blower Dis-

charg#_ lines up with the Duct Openin_ in the top of the

hood. Lift up the blower, slip the Bmower Mounting Rods into brackets on blower and tighten knurled nuts securely.

Plug in blower.

-d_ DUCT

_\ I_ MOUNTING

DISCHARGE J \ I ROD

Vertical discharge - blower position

BLOWER

DISCHARGE

DUCT

OPENING

BLOWER

MOUNTING

ROD

Horizontal discharge =bmowerposition

2. RemoveappropriateDuct Knockout(s_ from top or back

of hood.

TOP RECTANGULAR

DUCT KNOCKOUT

(Remove for 3¼" x 10"

vertical dJsc,#arge)

REAR RECTANGULAR

DUCT KNOCKOUT

(Remove for 3X" x 10"

horizenta! discharge)

3= Attach 31A" × 10" Damper/Duct Connector over knockout

opening. Make sure damper Pivot is nearest to Top/Rack

of hood. Remove any shipping tape from damper

flap.

TOP/BACK

EDGE

3X" x 10"

DAMPER/DUCT

CONNECTOR

SHiPPiNG

TAPE

¢e :S

PIVOT

1. Re@osition the btower for non-ducted discharge. Move the Blower Mountin_ Rods to the Front Holes in

the hood support channels. Position the blower so that it

lines up with the Louvered Opening on the hood front.

Slip the blower mounting rods into brackets on blower and tighten knurbd nuts securely. Plug in blower.

FRONT BLOWER

HARGE

il ._"_ x_/ I LOUVERED

BLOWER 1,// //-_-_,' i _ OPENING

MOUNTING lit. / ./_ y'_ c-_N 1

ROD It-

y'_.?'--_/ ! h

Non-ducted discharge - bmower position

2. Carefully pry off Louver Cover with a screwdriver or knife. Discard damper/duct connector, 1/4" black sheet metal

screws, and louver cover.

3. Purchase a Non-Ducted Kit, containing 2 Clean Cook- ing Filters.

See page 4 for Non-Ducted Kit information.

Non-Ducted Kit availab{e by calling Sears

at 1-800-4-MY-HOME _

4. Snap Aluminum Filter (provided with hood) into front

of Clean Cooking Filter. Make sure that Tab on alumi-

num filter lines up with Finaer Pull on Clean Cooking Filter.

FINGER

PULL

/ I _" LOUVER

COVER

CLEAN

COOKING

FILTER"--

TAB

ALUMINUM

FILTER

(from hood)

+ 22 hidden pages