Kenmore 23352159002, 23352154002, 23352153002, 23352152002, 23352059002 Owner’s Manual

...

ood

Use & Care / installation Manual

cocina

Manual de uso y cuidado /instalaci6n

Models Modelos

233.52052002 (30" wide - White)

233.52053002 (30" wide - Stainless)

233.52054002 (30" wide - Bisque)

233.52059002 (30" wide - Black)

233.52152002 (36" wide - White)

233.52153002 (36" wide - Stainless)

233.52154002 (36" wide - Bisque)

233.52159002 (36" wide - Black)

99043037H Sears, Roebuck and Co,, Hoffman Estates, UL60179 U,S,A, www,sears,com

SECTION ..................................................................... PAGE

Warranty .............................................................................. 2

Safety Instructions ............................................................... 2

Operation ............................................................................. 3

Cleaning .............................................................................. 3

Parts Included With Hood ................................................... 4

Parts Not Included With Hood ............................................ 4

Tools Needed ...................................................................... 4

Equivalent Duct Length Chart ............................................ 5

Prepare The Hood Location ............................................... 6

Prepare The Hood .......................................................... 7, 8

Connect The Wiring ............................................................ 9

Install The Hood ................................................................ 10

Service Parts ..................................................................... 11

Master Protection Agreements ......................................... 11

A iNTENDED FOR DOMESTIC COOKING ONLY.

If within 1 year from the date of installation, any part of this range hood fails to function properly due to a defect in mate-

rial or workmanship, Sears will repair the part or furnish and install a new part, free of charge.

FULL 30-DAY WARRANTY ON F_N_SHON PAINTED OR BRIGHT METAL PARTS

Ifwithin 30 days from the date of installation, the finish on any painted or bright metal parts of this range hood is defective in

material or workmanship, Sears will furnish and install a new 0art, free of charge.

WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS SEWCE CENTER/DEPART_'IENT

IN THE UNITED STATES.

This warranty applies only while this product is in use in the

United States. This warranty gives you specific legal rights

and you may have other rights which vary from state to state. Sears, Roebuck and Co,, Dept 817WA, Hoffman Estates,

IL 60179

WARNING ,_ A

TO REDUCE THE R_SK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufac- turer. If you have questions, contact the manufacturer at

the address listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the

service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the

service panel.

3. Installation work and electrical wiring must be done by a qualified person(s)in accordance with all applicable codes

and standards, including fire-rated codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting, re!low the heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), and the American Society

for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

5. When cutting or drilling into watl or ceiling, do not damage electrical wiring and other hidden utilities.

6. To reduce the risk of fire or electric shock, do not use this

range hood with an additional speed controi device.

7. Ducted fans must always be vented to the outdoors.

8. To reduce the risk of fire, use only metal ductwork.

9. This unit must be grounded.

TO REDUCE THE R_SK OF A RANGE TOP GREASE RRE:

1. Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when cooking flaming foods.

3. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for the size of the surface element. 2

WARNmNG _

TO REDUCE THE R_SK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UPA FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels

- a violent steam explosion will result.

4. Use an extinguisher ONLY if: A. You know you have a Class ABC extinguisher and you

already know how to operate it.

B. The fire is small and contained in the area where it

started. C. The fire department is being called. D. You can fight the fire with your back to an exit.

* Based on "Kitchen Firesafety Tips" published by NFPA.

CAUTION

1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction

dust, etc. off power unit.

3. For best capture of cooking impurities, your range hood should be mounted so that the top of the hood is 24-30"

above the cooking surface.

4. Use only with range hood cord-connection kits that have been investigated and found acceptable for use with this

model range hood.

5. Please read specification label on product for further information and requirements.

_fhood is to be installed NonoDucted:

e Purchase a non_ducted filter from your toccatadistributor

or retaimer and attach them to the aluminum mesh fimter.

NIGHT

LIGHT

Fan

The 4-position switch (on the left) controls the fan. The fan is OFF when the switch is rotated fully counterclockwise. Rotate

the switch clockwise to turn the fan ON to HiGH speed, to MEDIUM speed, and to LOW speed.

_ WARNING: To reduce the risk of electric shock,

disconnect from power supply before clean- rag.

)

Aluminum mesh filter Clean frequently using hot water and a mild detergent or in

your dishwasher. The aluminum mesh filter should be washed approximately every month depending on the amount of us-

age. Wash more often if your cooking style generates greater grease - like frying foods or wok cooking.

Nonoducted filter (Clean Cooking hoods onmy)

(available separately - see page 4)

Clean filter surfaces frequently with a damp ctoth and a mJId detergent. DO NOT immerse fiIter in water or put in dish-

washer. The speciaJ "Clean Sense" feature indicates when the filter is to be repIaced. The biue and yel!ow strips will bIend to

green when it is time to change the filter. The "CIean Sense" feature works best when facing toward the cooking surface.

Light

The 3-position switch (on the right) controJs the light. The Iight is OFF when the switch is rotated fully counterclockwise. Ro-

tate the switch clockwise to turn the light ON for normal light- ing, and to use as a night light.

Painted hood surfaces Wiping reguIarly with mild soap/detergent and warm water

should protect painted hood surfaces. Be cautious about us- ing "New and improved" cleaning agents. Your hood is installed

over hot cooking equipment. Most chemicaIs found in clean- ing agents react with heat to loosen paint.

StainJess eteemhood surfaces StainJess steel hoods should be washed regularly with a clean

cloth, warm water and mild soap or dish detergent. Clean in the direction of the polish Iines. Rinse well with clear water

and wipe dry immediately. You may wish to apply light oil used for furniture polishing to emphasize it's bright finish.

Fan aseembBy Fan bIade can be cJeaned with a damp cJoth and mild deter-

gent. Use care when cteaning fan blade - it must not become bent or misa[igned. DO NOTALLOW WATER TO ENTER MO- TOR. Make sure alI surfaces are completely dry before re-

installing filters and restoring power. Motor is permanentJy Jubricated. Do not oJJor disassembJe

motor.

O_ q_

Aluminum Grease Fimter

3%" x 10" Damper/Duct Connector

Parts Bag (4 hood mounting screws inside)

Light Bulbs (75 W Maximum)

(2 per hood) Purchase locally.

OPTmONAL PARTS (purchase separately)

Clean Cooking Filter

(Non-ducted hoods only) (1 per hood)

Sears Part No. 99010317

(For use with 7-inch Round Duct) 7oinch Round Damper

Sears Part No. 59183

Spmashp_ate Sears Part Nos.

58120 30" Black/Bisque 58128 30" White/Almond 58129 30" Stainless

58130 36" Black/Bisque

58138 36" White/Almond 58139 36" Stainless

Sacrewdriver

t & Phillips)

Saw

Cord Kit (Allows hood to be plugged into a

standard 120 VAC wall outlet)

Sears Part No, 233,22HCK44D

Ducting Accessories (See "Equivalent Duct Length Chart" on page 5 for Ducting

Accessory Model Nos.)

"Parts Not Included With Hood" available by calling m

Sears at t-800_4-MY_HOME _

t_ TapeMeasure

_N 1/4"

Duct Tape

4_S wire

utdriver

tripper

KenmorerangehoodsaredesignedtoperformefficientlywhenattachedtoIongrunsofduct.Asapointofreference,thishood wiIIfunctionatapproximately80%ofitsratedairftowwhen200equivalentfeetof7"roundductworkisattached.Usethischart

tocalculatetheequivalent duct length of your system.

Broan Modem 401

Straight Duct

3¼=in, × lO-in, × 2=ft, mong

Equivalent length

2ft.

( 0

Broan Modem406

Straight Duct

64n. round × 2-ft, long

Equivalent length

2 ft.

( 0

Broan Modem407

Straight Duct

7-in. round × 2-ft. long

Equivalent length

2 ft.

64n, Round Elbow

Broan Modem419

Equivalent length

8 ft.

Broan Model 428

3¼-in° × lO=in.

Right=angBe Embow

Equivalent Iength

8.5 ft.

3¼-in. × lO-ino

Right-angle Fiat Elbow

Broan _'1odel 429

Equivalent length

24 ft.

Broan Model 430

3¼-in. × lO-ino

Right-angme

Short

Eave E{bow

quivalent length

15 ft.

Broan Model 431

3¼-in, × lO-ino

Right-angle

Long

Eave Elbow

quivalent length

15 ft.

8=in° Round

Wall Cap

(_ Sears Modem59691

Equivalent length

34 ft.

(6-ft= w/o damper)

74n. Round

WaR Cap

(_ Broan Modem047

Equivalent length

34 ft.

(6-ft= w/o damper)

Sears Model

59391

3¼-in. x

lO-in,

WaR Cap

Equivalent

length

45 ft.

(7tit= w/o damper)

Model 59091

Roof Cap

(accepts 74n. round

or 3¼-in. × lO-in, duct}

Equivalent Iength

30 ft. (7-fL W/Odamper)

7-in, Round Elbow

Broan Modem415

Equivalent length

8 ft.

3¼-ino × 104n° to

6=in. Round Transition

Sears Model 59501

Equivalent Iength

5.5 ft.

3¼4no × lO=in, to

7=in°Round

Broan Model 412R

Transition

Equivalent Iength

5.5 ft.

Sears Modet "Ducting Accessories" avaimabmeby caring:

Sears at 1-800=4=[v]Y=HOME®

Broan Modet "Ducting Accessories" availabme by caring:

1_800=558=1711°

1. Determine whether hood will discharge vertically (3¼" x 10" or 7" Round), horizontally (3V4"x 10" only) ornon-ducted.

For vertical or horizontal discharge, run ductwork between

the hood location and a roof cap or wall cap.

For best results, use a minimum number of transitions and

elbows.

ROOF CAP

SOFFIT

CABINET -._..

24" -30" ABOVE COOKINGSURFACE

3W'X 10" or 7" ROUND DUCT

(For vertical discharge)

HOUSE WIRING

or Back of hood)

CAP

3W' X 10" DUCT (For horizontal discharge)

2. Use these diagrams for proper placement of ductwork and

electrical cutout in cabinet or wall.

For a non-ducted installation, DO NOT cut a duct access hole.

3. Run house wiring between service panel and hood location.

I 7" ROUND ]

HOOD MOUNTING SCREWS (4)

VERTICAL DUCTING

3W'X 10"

HOOD MOUNTING SCREWS (4)|VERT CAL DUCT NG

CABmNET]BOTTOM ]

q-C-, m vEm,o*Louo,7,k ,*"

5" _' m ACCESSHOLE m k_-__

ELECTRICAL

WOOD SHIMS CENTER

(recessed-bottom LINE (in cabinet bottom)

cabinets only)

WOODSHIMS [ 31A'X10" 1

(recessed-bottom HORIZONTAL DUCTING

cabinets only)

CABmNETFRONT

ACCESS HOLE

WOOD SHIMS _ ELECTRmCAL

(recessed-bottom CENTER (in cabinet bottom)

cabinets onmy) LiNE

ACCESS HOLE

1615/16" (36" hood)

HOOD

MOUNTING

SCREWS (4)

1615/16" (36" hood) !

CENTER

LINE (in wall)

ELECTRICAL

ACCESS HOLE

1. Remove_ fromnoseofhood.

2.Remove ,Aluminum Mesh Filter and

31A"× 10" Duct Connector from inside the hood. Set filter and duct connector aside.

3. Remove WiringCover from inside the hood. Set cover and mounting screw aside.

SHIPHNG

TAPE

3¼"X10"

DUCT

CONNECTOR

ALUMINUM

MESH

FILTER

WIRING COVER

4. Remove either top or back Wiring Knockout and install approved Electricam Cabme Cmamp,

ELECTRICAL

CABLE CLAMP

WIRING

KNOCKOUT

5.Removethe7oinch Round Adapter Pmatefrom the top of 7-iNCH ROUND

the hood. ADAPTER PLATE

tf hood is to be installed Non-Ducted:

o Purchase Clear Cooking Filter. e Install the Clean Cooking Filter behind the aluminum

mesh filter.

e Skip to "CONNECT THE WIRING"o

See page 4 for Clean Cooking FHter information,

CmeanCooking FHter available by calling Sears

6. Remove appropriate Duct Knockout S(LS)from top or back of hood.

at 1-800o4oMY_HOME _

TOP SEMFCIRCULAR DUCT KNOCKOUT

(Remove for 7" round vertica/ discharge)

tf using 7" round ductwork:

Remove both the Rectangular

Duct Knockout and the SemF circular Duct Knockout from the top of hood.

7. if using 31/4'' x 10" rectangular ductwork: Attach 31A'' x 10" Damper/Duct Connector over

knockout opening. Make sure damper Pivot is nearest to W/Back Edge_ of hood. Remove any shipping tape

from damper flap. tf using 7" round ductwork:

Re-install the 7qnch Round Adapter Plate removed in

Step 5.

Purchase a 7" Round Damper.

See page 4 for 7" Round Damper information,

7" Round Damper is avaHabme by calling Sears

at 1-800-4_MY_HOME _

TOP RECTANGULAR

DUCT KNOCKOUT

(Remove for 3¼" x 10"

& 7" round vertical

discharge)

REAR RECTANGULAR

DUCT KNOCKOUT

(Remove for 3¼" x 10"

horizom'al discharge)

3V4"x 10"

DAMPER/DUCT

CONNECTOR

PIVOT TOP/BACK

EDGE

8. Install Vent Cover into slot, behind louvers at the front of hood.

+ 16 hidden pages