Kenmore 158220, 15812260, 15812250, 158121, 15812020 Owner’s Manual

158.120

158.12000

158.12020

15g.121

158.12250

158.12260

158.220

STRAIGHTSTITCH ATTACHMENT ZIGZAG BITE FOOTCONTROL

POSITION DIMENSION

CF._TER HIGH BAR 6.8 6811

PRESSERFOOTHEIGHT

d Sw l

BKIf:G THE ZIGZAG CAN GUIDE (l) TO ITS r,XTRE/tE LEFT L_D POSITION
bY TURNING THE HAND'EEL* AT THIS POSITION OF ZIGZAC C_M GUIDE,

MOVE THE STITCH WIDTH CON._ROL FROH O TO 4, AND THEN FROH _ TO O,

CHECKING TO(. SEE IF THE NEEDLE SW][NGS. THE NEEDLE SHOULD NOT

SWING. IF ADJUSTHENT IS NECESSARY, LOOSEN SET SCREW (2) AND
ADJUST POSITION OF THE BASE, OR BASE STOPPER (3), REPEATING THE

ABOVE PROCEDURE. TIGHTEN THE SCREW SECUItELY AFTER ADJ_STHENT.

LOW|ARTYPE

..__._13 6 MM

MINIMUM

52 MM

NEEDLE PLATE SURFACE MINIMUM

HIGH BARTYPE

62 MM

FRONTFACINGSHUTTLE

SUPER HIGH lIAR TYPE (

MINIMUM

5.2 MM

SlOE FACINGSHU'i'rLE

FI €,_RF C-I

SUPERHIGH BAR LOW BAR HIGH BAR LOW BAR

Drop feed dog Pressdownpressureregulatortothe max;mum pressureLowerpressorPfootlever LoosenIhumb soew andbe
sure presser foot os seated properly Taghtenthumb screw

If adluslmenl asnecessary,raise presserloot lever and loosenscrewson pressor bar holder Adlustthe hefght of p_es_effoot
from needle plate as specdled Conformthe height of presser toot by a complete turn of the handwheel T_ghtenthe sc|ews

securelyafter adjustment

i158.18010

158.120

158.12000

158.12020

158.121
1 58.12250

158.12260
1 58.220

Feed 0cO Height

:OR FRO_ITFA,_,I:_GSHUTTLE '_g&ELS,-_LzC_;_US[ _T ;OS:TIOI__,S;LL.STR'.'ZC
._ITHTHE _IO-GO-SI_EOF THE SALSE F':,C:_S"_E ':Z=SL__L_TE. LO'.IER_R[_.._ZR
FOOT. WHILE TL'RNI:,GT_F 4A:|G'._HEELSLOWL¢ 3v _';D, ÷uE SALGE GHOUL] SE

'4OVE3BY THE FEEDCOG TEETH. ;F :40T, :EE_DOG TF.F'T_._RE "00 LO._._HE'_
PLACE THE GAUGE UP-SIDE-DOW_J'rITHT._ESO-SIDE FACI',GT#[ ',EEDLEPLATE.
REPEAT THE SM'IEPROCEDURE. THE GAUGE SHOULD ;.'OTBE '_OVED. I_ THE GAUGE

IS ,_IOVED,THE FEEDDOG TEETH ARE TOO HIGH.
IN CHART FORM IT LOOKS LIKE THIS:

NeedlePmdtle.

Set thestitch width control at maximum Turnlni
the handwheel,cheek and see If the nero goes

throuEh the needle slot at points of equal diltanee

from each end of the needle slot.

If not, loosen the set screws on the bracket of vertical
rocker shaft, and adjust as illustrated. T_hten the

set screws securely after adjustment.

FIGURE D-I

Feed Dog Height Go-Side (FacingI r|o-Go-Si_ (Facing l ,,oNo_ossos

COrrect Hot Moving I Moving _._-------_/

Low Hot Moving lHot Moving

Gauge Needle Plate} I Needle P_ate) i '"
High _ovlng J Moving

IF ADJUST)IE'ITSARE :IEOESSARY,LODGE';SCRE:(',ll0_IDROP ,€':'-.=-_'I'[_"_LD_Kr'

&:(DADJUST T#E FEEDDOG HEIGHT AS SPECIFIED. TIGHTE_ T_[ SCI[',.;S[;.JREL'_
AFTER ADJUS,_,<E'4T.

CAUTION: FOR SIDE FACI2;GSHUT'L[ _ODEL BE SURE T_E )AUGE

IS _LACED ON THE SJRFACE OF :|EEDLEPLATE. B_.

SURE ONE E'¢OIS 'lOTRESTING ON .'HEHANDHGLE
COVER PLATE.

I

• _ • o ,

158.18010

/

. _,_;-

I

\