Kenmore 15817520, 15813180 Owner’s Manual

1_8.t7S20

STRAIGHt STITCH ATTACHMENT ZIGZAGBITE FOOT CONTROL

POSITION DIMENSION

CI_NTER LOW BAR 5.8 6813

n n ham

L,

PRESSERFOOTHEIGHT

LOWBARTYPE

ti.li MM

HIGH OARTYPE SUPERHIGH OARTYPE

_t

li.S MM

MINIMUM

5,2 MM

t

NEEDLE PL:TE SURFACE

MINIMUM

S.2 MM

Oimibuti,n ,f Noodle Swing

Dean| the noodle to its lowest pcaLtlon by turnln4;

the bsndwheol. At this neeole position, t-tu.nthe

ar[ItchwtdtheomrolfromOtoms.-.Imum and back

to O. and oote the _latamce needle travel= from

its center poaxtlon towa, r_ one slde.

•rum the haadwhae! Onecomplete turn, an4br/nl[
the naedJa to lie ]owens poaltlon q[;u_. ,_ow thla
ttme, the needle travele to the oppoeite side trom
Its center posLtton, _ you tux_ the stitch width

€0atrol from 0 to maxizoum, autdb:pek*.oO. Yots

ebe _a.*-ce needZe tz,..4yeIL

the Wee,no trAvolJ unev_'A dtJt_mcen from Its

€lmtsr position, loosen set screw (I), _mdadJust
pooP.fen of follower rocker pi.nby tu,'n_m4_eooen..

aria pin (2), until you obtain an oven dlstrtt'i'._tton

the needle _ M LU,atr-_ted (3), Tfpsen

the set screws se¢_rel), attar a_e_..

5.2 MM

FRONTFACINGSHUTTLE

t

SIDE FACINGSHUTTLE

SUPERHIGH BAR LOW BAR HIGH BAR LOW BAR

Dropfeed dog Pressdownpressureregulator to the mexvmumpressure Lowerpressurefootlever Loosenthumbscrewandbe
sure presser foot vs seated properly T,ghten thumb screw

If adlustment _snecessary,raesepresserfootfeverand loosenscrewson presserbar holder Adlustthe he,ghtof presserfoot
from needleplate as specd,ed Confvrmthe hevghtof presserfoot by o completeturn of the handwheel Ttohtenthe screws

securelyafter adlustment

F T.GURE C-6

FIGURE A-F

P km

FeedOegHeight

:OR _O'IT ;AC;'4GSHUTTL-Z_ODELG, _LACE ;AUGE _ )OS..........., tS ,._ S-RATE2

.liT.THE :1g-GO-SIDEOF ,_ =_uo: _ACI'_ T'_E";[Z3L-_L;_TE..I,E_,._rE_.:_:

FOOT. '.,H;LETUR,r,I._G"HE .A;,CWHEELSLJWLf BY "_.ID,'-E _._,,:_aOSL] :_
'_OVE3_Y THE F_EDDOG " _

PLACE THE GAbGE Um-SIDE-DO'_N"ITH T_E _O-S,DE FAC",_ ?.E '4EL5LEmLAT_.
REPEAT THE S_4E PROCEDURE. THE GAUGE SHOULD NOT BE '.IOVE_.IF THE GAUGE

IS HOVED, THE FEEDDOG TE_H ARE IOO HIGH.
IN CHART FORM IT LOOKS LIKE THIS:

Feed Dog Height GO-el-de(Facing No-Go-side (Facing .o No._os,o{
Gauge Needle Plate). Needle Plate) /

Correct [iotMoving Moving _-_'_
Low Not Moving riotMoving "_'-'_"-"_
High Moving (1ovlng _ ,,o_

IF ADJUST':EtlTS_RE 'iECkSSARY,LCOSE_4SCRE',iI) or4DROP FE:.3_E'_ER "_LGCK

A:IDADJ,JS:"THE F{EDDOG HEIGHT AS SPECIFIED. T,G_ ,E,;T_E SORE^ SEC'_REL,
AFTER ADJUS_(ENT.

.'AUTIG_I:_CR SID#.FAC;'(GSHUTTLE MOOEL BE SURE "HE GAUGE

IS _LACED OilTHE SURF:CE OF NEEDLE PLATE. BE

SURE Or4EEr;D,.'__'iOTRESTI'4GON THE HAHDHOLE

COVER _L:TE.

,E., . ;F 21OT,FEZDD{_ T_.---'._ _RE CO ..,;.TvE',

T

FIGURE D-t

--- ........

----- °

i

c_

I

\

T

FI(,URE _-].