Kenmore 15223151910 Owner’s Manual

Use & Care Guide Manual de Uso y Cuidado

4 Burner LP Gas Grill with Side Cart

Parrilla a gas LP con 4 quemadores y carro lateral

Model/Modelo: 152.23151910

Sears Brands Management Corporation

Homan Estates, IL 60179 U.S.A. www.kenmore.com

These instructions are for your safety. Read them thoroughly before use and retain them for future reference.

WARNING:

Do not store or use gasoline or other

ammable vapors and liquids in the vicinity of this or any other appliance. An LP-cylinder not connected for use shall not be stored in the vicinity of any other appliance.

WARNING:

For Outdoor Use Only!

WARNING:

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read the installation, operating and

maintenance instructions thoroughly

before installing or servicing this equipment.

DANGER:

If you smell gas:

1. Shut o gas to the appliance.

2. Extinguish any open ame.

3. Open lid.

4. If odor continues, keep away from

the appliance and immediately call

your gas supplier or re department.

Table of Contents

Parts Supplied 4 Hardware and Before You Start 5

Diagram and Part List 6 Assembly Steps 7 Leak Testing 23 Safety Instructions 24 User Instructions 25 Care and Maintenance 26 Grill Specications and Troubleshooting Warranty 30 Service Number Back Cover

Parts Supplied

Ref Description Illustration Qty Ref Description Illustration Qty

Cabinet Base

Left + Right

Brace Plate

Front Panel

Side Wall

Cabinet

Cross Bar

Fold-down

Side Shelf

Vaporising

Bar

Cooking

Grate

Searing

Grate

Warming

Rack

Axle

Assembly

Locking

Caster

Wheel

Cylinder

Supports

Firebox

Grease

Tray

Grease Cup

Bracket

Grease

Cup

Cart Wheel

Bracket

Left Cart

Frame

Cart

Wheel

Parts Supplied

Hardware Supplied

Ref Description Illustration Qty

Right Cart

Frame

Cart Shelf

Cart Rail

Side Cart

Handle

Ref Description Illustration Qty

M6 x 12

Bolt

M4 x 10

Bolt

M6 x 45

Bolt

Hardware items are not shown at actual

size.

Side Cart

Tabletop

Utility Bin

Chopping

Board

Before You Start

Check the contents of the box and make sure you have all the parts and ttings listed. If not, call 1-844-553-6667. When you are ready to start, make sure that you have the right tools at hand, plenty of space and a clean dry area for assembly.

Assembly

Lay out all nuts and bolts and check lengths before assembly. It is recommended that the

carton is cut open and spread out on the

oor and used as a protective surface during assembly. Refer to the assembly diagrams as necessary.

CAUTION: While every precaution has been made in the manufacture of this product, care must be taken during assembly in case sharp edges are present.

Diagram

A01

A02

A03

A04 A05

A06

A07

A08

A09

A10

A11

A18

A19

A20

A21

A22

A12

A13

A14

A15

A16

A17

Part List

Key Description Qty Part Number

A01 A02 A03 A04 A05 A06 A07 A08 A09 A10 A11 A12 A13

Lid

Temperature Gauge

Logo

Lid Handle Bezel

Lid Handle

Firebox

Rotate Rod

Left Back Side Shelf Bracket

Left Front Side Shelf Bracket

Right Back Side Bracket

Right Front Side Bracket

Bottle Opener

Bezel Control Dial

506 A01

506 A02

506 A03

506 A04

506 A05

506 A06

506 A07

506 A08

506 A09

506 A10

506 A11

506 A12

506 A13

A23 A24

A25

A26

Key Description Qty Part Number

A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26

Control Dial

Grease Tray

Grease Cup Bracket

Grease Cup

Warming Rack

Cooking Grate

Searing Grate

Vaporising Bar

Burner

Gas Valve

Manifold

Gas Hose

Regulator

506 A14

506 A15

506 A16

506 A17

506 A18

506 A19

506 A20

506 A21

506 A22

506 A23

506 A24

506 A25

506 A26

Assembly Step 1

Cabinet Base

Fit left and right side walls to the cabinet base as shown below using 8 of the M6 x 12 bolts.

Note: The right side wall has a hole in the top corner.

This is a view from the back.

Right Side Wall Left Side Wall

Left + Right Side Wall

M6 x 12 Bolt

Assembly Step 2

Cabinet Brace Plate (x2)

Fit the two cabinet brace plates to the cabinet base and side wall assembly using 8 of the M6 x 12 bolts as shown below.

M6 x 12 Bolt

Cabinet Brace Plate

M6 x 12 Bolt

Assembly Step 3

Cabinet Front Panel

Note: Flip cabinet assembly over so that the left side wall is on the oor.

Fit cabinet front panel to base and side wall assembly as shown below using 6 of the M6 x 12 bolts. Note: An extra person will be needed to hold the door in position while tightening the bolts.

M6 x 12 Bolt

Cabinet Front Panel

Assembly Step 4

Cross Bar

Fit the cross bar using 4 of the M4x10 bolts.

Secure chain to cabinet front panel using the pre-tted M6 x 12 bolt and washer.

Cross Bar

M4 x 10 Bolts

Assembly Step 5

Axle Assembly Locking Caster

Wheel (x2)

Turn the cabinet assembly over and t axle assembly and two locking caster wheels to the underside of the

cabinet base using 16 of the M6 x 12 bolts.

Note: Axle side with cutout goes to back side of cart. Note: Once grill is assembled and rolled into position, press caster levers down to lock casters in place.

Always detach side cart from grill when moving grill.

Axle Assembly

Cabinet Base

M6 x 12 Bolt

Locking Caster

Wheel

Assembly Step 6

Cylinder Supports

Turn the cabinet assembly over and t the two cylinder supports to the cabinet base using 6 of the M6 x 12

bolts.

Cylinder Support

M6 x 12 Bolt

Assembly Step 7

Firebox

Cut the zip ties securing regulator and hose to underside of rebox. Allow hose to hang straight down when lowering rebox onto cart. Position rebox onto cabinet. Open hood and use 4 of the M6 x 12 bolts to secure rebox into position. Be sure that edges of rebox are even with edges of cart before tightening bolts.

Note: Attachment holes are located on inside of rebox (2 on each side). Note: Two people are required to lift rebox into position.

M6 x 12 Bolt

Assembly Step 8

Fold-down Side Shelf

Remove the pre-tted R-clips and pins from brackets on side of rebox. Insert the shelf brackets into the rebox brackets and align the holes. Reinsert pins and clips through the

holes to secure the shelf in place.

To raise the shelf to use position, lift shelf up and hold it against side of rebox with one hand. Use other hand to reach below shelf to lift up long bar and insert it into rebox bracket hooks. To fold shelf down,

reach below shelf to lift up long bar with one hand, and gently lower shelf with other hand.

Long bar

R-clip and pin

Assembly Step 9

Vaporising Bar (x4) Cooking Grate (x3) Searing Grate Warming Rack

1. Fit vaporising bars (x4) into position as shown.

2. Fit cooking grates (x3) and searing grate into position as shown.

3. Fit warming rack into position as shown.

Note: As a convenience feature, there is a bottle opener on the left side of the rebox.

Note: The Searing Grate must be positioned over the Searing Burner. For searing purposes the Searing Burner

(14000 BTU) is hotter than the other three burners (11700 BTU). The Searing Grate design is also dierent than the

other three grates. Its diamond check pattern will sear into the surface of the meat.

Warming Rack

Assembly Step 10

Grease Tray Grease Cup Bracket

Attach grease cup bracket to grease tray using one of the M6 x 12 bolts and then slide tray into the back of the grill as shown below. Open the front panel door and slide grease cup into the grease cup bracket as shown. Note: Access the grease cup to remove for cleaning by lowering the front panel door. Also, as a convenience feature, there are three beverage container holder recesses on the inside of the door.

Grease Cup

Grease Cup Bracket

Grease Cup

M6 x 12 Bolt

Grease Tray

Assembly Step 11

Cart Wheel (x2)Cart Wheel Bracket (x2) Left Cart Frame

1. Fit cart wheel brackets to left cart frame as shown below using 8 of the M6 x 12 bolts.

2. Fit the 2 cart wheels to the cart wheel brackets using pretted bolt and washer attached to the tip of the

wheel axles.

M6 x 12 Bolt

Assembly Step 12

Right Cart Frame

Lay the left cart frame down and attach the middle cart shelf rst using 2 of the M6 x 12 bolts. Then attach the bottom cart shelf using 3 of the M6 x 12 bolts (Ref A). Then attach the right cart frame to the assembled shelves using 5 of the M6 x 12 bolts (Ref A).

Note: There are 3 height options for the shelves.

Cart Shelves (x2)

M6 x 12 Bolt

Note: Bolt attachment points are located underneath the cart shelves.

+ 42 hidden pages