Kenmore 11098752796 Owner’s Manual

24" Wide (61 cm)

LAUNDRY CENTER

Washer - Gas Dryer

CENTRO DE LAVANDERIA

de 24" (61 cm) de ancho

Lavadora - Secadora a gas

Model/Modelo 110.98752

I i

Wt00350t 0 Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com

TABLEOF CONTENTS

KENMORE APPLIANCE

WARRANTY ..................................................................................... 2

WASHER/DRYER SAFETY ............................................................ 3

INSTALLATION INSTRUCTIONS .................................................. 5

Tools and Parts ............................................................................ 5

Alternate Parts .............................................................................. 5

Location Requirements ............................................................... 5

Drain System ................................................................................ 7

Electrical Requirements ................................................................ 7

Gas Supply Requirements ........................................................... 8

Venting Requirements .................................................................. 9

Install Leveling Legs .................................................................. 10

Remove Foam Packing ............................................................. 10

Connect Drain Hose .................................................................. 10

Connect Inlet Hoses .................................................................. 11

Secure Drain Hose .................................................................... 12

Plan Vent System ...................................................................... 12

Install Vent System .................................................................... 13

Level Laundry Center ................................................................ 14

Make Gas Connection ............................................................... 14

Connect Vent ............................................................................. 14

Complete Installation ................................................................. 15

WASHER USE .............................................................................. 16

Starting Your Washer ................................................................ 16

Cycles ........................................................................................ 17

Rinse and Spin .......................................................................... 17

Drain and Spin ........................................................................... 17

Understanding Washer Cycles .................................................. 18

Normal Sounds .......................................................................... 18

LAUNDRY TIPS ............................................................................ 18

Loading ...................................................................................... 18

DRYER USE ................................................................................. 19

Starting Your Dryer .................................................................... 19

Stopping and Restarting ........................................................... 19

Loading ...................................................................................... 19

Drying, Cycle and Temperature Tips ........................................ 20

Cycles ........................................................................................ 20

LAUNDRY CENTER CARE ......................................................... 21

Cleaning the Laundry Center Location ..................................... 21

Cleaning Your Washer ............................................................... 21

Water Inlet Hoses ...................................................................... 21

Cleaning the Lint Screen ........................................................... 21

Cleaning the Dryer Interior ........................................................ 22

Removing Accumulated Lint ..................................................... 22

Vacation, Storage and Moving Care ......................................... 22

TROUBLESHOOTING WASHER ................................................ 23

TROUBLESHOOTING DRYER .................................................... 25

PROTECTION AGREEMENTS .................................................... 26

SERVICE NUMBERS ............................................... BACK COVER

WARRANTY

ONE YEAR LIMITED WARRANTY

When installed, operated and maintained according to all instructions supplied with the product, if this appliance fails due to a defect in material or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME ®to arrange for free repair.

If this appliance is used for other than private family purposes, this warranty applies for only 90 days from the date of purchase.

THIS WARRANTY COVERS ONLY DEFECTS IN MATERIAL AND WORKMANSHIP. SEARS WILL NOT PAY FOR:

1. Expendable items that can wear out from normal use, including but not limited to filters, belts, light bulbs, and bags.

2. A service technician to instruct the user in correct product installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed, operated or maintained according to all instructions supplied with the product.

5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

Customer's sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Implied warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law. Sears shall not be liable for incidental or consequential damages. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitations on the duration of implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to you.

This warranty applies only while this appliance is used in the United States and Canada.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co.

Dept. 817WA, Hoffman Estates, IL 60179

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2B8

PRODUCT RECORD

In the space below, record your complete model number, serial number, and purchase date. You can find this information on the model and serial number label located on the product.

Have this information available to help you obtain assistance or service more quickly whenever you contact Sears concerning your appliance.

Model number

Serial number

Purchase date

Save these instructions and your sales receipt for future reference.

WASHER/DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

I WARNING: For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, or to prevent property damage, personal injury, or death.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Clear the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

In the State of Massachusetts, the following installation instructions apply: i Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

i If using a ball valve, it shall be a T-handle type. i A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer/dryer, follow basic

precautions, including the following:

[] Read all instructions before using the washer/dryer. [] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

[] Do not wash or dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or explode.

[] Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water. These substances give off vapors that could ignite or

explode.

[] Do not allow children to play on or in the washer/dryer.

Close supervision of children is necessary when the washer/dryer is used near children.

[] Before the washer/dryer is removed from service or

discarded, remove the doors to the washer/dryer compartments.

[] Do not reach into the washer/dryer if the tub, agitator or

drum is moving.

[] Do not install or store the washer/dryer where it will be

exposed to the weather.

[] Do not tamper with controls. [] Clean dryer lint screen before or after each load.

SAVE THESE INSTRUCTIONS

[] Under certain conditions, hydrogen gas may be produced

in a hot water system that has not been used for 2 weeks

or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using

the washing machine, turn on all hot water faucets and let the water flow from each for several minutes. This will

release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.

[] Do not repair or replace any part of the washer/dryer or

attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair

instructions that you understand and have the skills to carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust, and dirt.

[] The interior of the machine and dryer exhaust vent should

be cleaned periodically by qualified service personnel.

[] See "Electrical Requirements" for grounding instructions.

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSi Z223.1/NFPA 54.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70.

INSTALLATION INSTRUCTIONS

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

Tools needed:.

8" or 10" adjustable • Knife wrench (for gas

connections) • Vent clamps Flat-blade screwdriver • Pipe-joint compound

resistant to LP gas

Adjustable wrench that opens to 1" (2.5 cm) or • Caulking gun and

9/16"(14 mm) open-end compound (for installing wrench (for adjusting new exhaust vent)

dryer feet) • Pliers Level • Ruler or measuring tape 1A"nut driver or socket • Tin snips (new vent

wrench (recommended) installation)

• Wood block (for leveling)

Parts supplied:

Remove parts package from the washer basket. Check that all parts were included.

Parts listed are available from your local Sears store or Sears Service Center. For further information, please call

1-800-4-MY-HOME® (1-800-469-4663).

If You Have You Will Need to Buy

Laundry tub or Sump pump system (if not already standpipe taller than available) 96" (2.4 m)

1" (2.5 cm) diameter 2" (5 cm) diameter to 1" (2.5 cm) standpipe diameter standpipe adapter, Part

Number 3363920

Overhead sewer Standard 20 gal. (76 L) 34" (86.4 cm)

tall drain tub or utility sink and sump

pump (available from local plumbing suppliers)

Floor drain Siphon break, Part Number 285320,

additional drain hose, Part Number 285702 and connector kit, Part Number 285442

Drain hose too short Drain hose, Part Number 285664 and

connector kit, Part Number 285442

Lint clogged drain Drain protector, Part Number 367031

C D

A. Water inlet hoses (2) B. Inlet hose flat washers (4)

C. Rear leveling legs (2) D. Front leveling legs (2)

Parts needed:

Check local codes and with gas supplier, check existing gas supply, electrical supply and venting, and read "Electrical Requirements," "Gas Supply Requirements" and "Venting Requirements" before purchasing parts.

Mobile home installations require special parts (listed following) available for purchase from your local Sears store or Sears Service Center. For further information, please call 1-800-4-MY-HOME ®(1-800-469-4663).

• Mobile Home Installation Kit. Ask for Part Number 346764.

• Metal exhaust system hardware.

E. Plastic strap F. Drain hose

G. Yellow, single wire hose clamp H. Silver, double wire hose clamp

Water faucets 2 longer water fill hoses: beyond reach of fill 6 ft (1.8 m) Part Number 76314, hoses 10 ft (3.0 m) Part Number 350008

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Failure to do so can result in death, explosion, or fire.

You will need

• A location that allows for proper exhaust installation. A gas laundry center must be exhausted to the outdoors. See "Venting Requirements."

• A grounded electrical outlet located within 2ft (61 cm) of either side of the laundry center. See "Electrical Requirements."

• Asturdyfloortosupportthelaundrycenterweight(laundry center,waterandload)of500Ibs(226.8kg).

Alevelfloorwithamaximumslopeof1"(2.5cm)underentire laundrycenter.Clothesmaynottumbleproperlyand automaticsensorcyclesmaynotoperatecorrectlyiflaundry centerisnotlevel.Installingoncarpetisnotrecommended.

• Awaterheatersettodeliver120°F(49°C)watertothe washer.

• Hotandcoldwaterfaucetslocatedwithin4ft(1.2m)of thehotandcoldwaterfillvalves,andwaterpressureof 5-100psi(34.5-689.6kPa).

Thelaundrycentermustnotbeinstalledorstoredinanarea whereitwillbeexposedtowaterand/orweather.

Donotoperateyourwasherintemperaturesatorbelow 32°F(0°C).Somewatercanremaininthewasherandcan causedamageinlowtemperatures.See"Vacation,Storage,and MovingCare"forwinterizinginformation.

Donotoperateyourdryerattemperaturesbelow45°F(7°C).At lowertemperatures,thedryermightnotshutoffattheendofan automaticcycle.Thiscanresultinlongerdryingtimes.

Checkcoderequirements.Somecodeslimit,ordonotpermit, installationofthelaundrycenteringarages,closets,mobile homes,orsleepingquarters.Contactyourlocalbuilding inspector.

NOTE:Nootherfuel-burningappliancecanbeinstalledinthe sameclosetasadryer.

Installation Clearances

The location must be large enough to allow the dryer door to open fully.

Laundry Center Dimensions

15%"

(39.05 crn)

71 3/4"

(192.25 cm)

Minimum installation spacing for recessed area or closet installation

The following dimensions shown are for the minimum spacings

allowed.

• Additional spacing should be considered for ease of installation and servicing.

• Additional clearances might be required for wall, door and floor moldings.

For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

• Rear clearance may be 1" (2.5 cm) when house exhaust system is lined up directly with dryer exhaust.

3__ 1" ,_ ,_ (2.5cm) ---

48in? -

(610cm2} -_-i ' (7'6cm)

24in? _ ,_

(196om2)_

-- _' (7.6cm)

61/2'

(14era)

A. Recessed area B. Side view - closet or confined area C. Closet door with vents

Mobile Home - Additional Installation Requirements

This laundry center is suitable for mobile home installations. The installation must conform to the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280).

Mobile home installations require:

• Metal exhaust system hardware which is available for purchase from your local Sears store or Sears Service Center.

• Mobile Home Installation Kit Part Number 346764. See "Tools and Parts" section for ordering information.

Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.

*271/4"

(69.22 cm)

*Most installations require a minimum 51/2'' (14 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting Requirements."

_ "_i¸ _"_

Thelaundrycentercanbeinstalledusingthestandpipedrain system(floororwall),thelaundrytubdrainsystem,orthefloor drainsystem.Selectthedrainhoseinstallationmethodyouneed.

See"AlternateParts."

Standpipe drain system - wall or floor (views A & 13} The standpipe drain requires a minimum diameter standpipe of

2" (5 cm). The minimum carry-away capacity can be no less than 17 gal. (64 L) per minute. A 2" (5 cm) diameter to 1" (2.5 cm) diameter standpipe adapter kit is available. See "Alternate Parts."

The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (2.4 m) from the bottom of the washer.

A B

Laundry tub drain system (view C) The laundry tub needs a minimum 20 gal. (76 L) capacity. The top

of the laundry tub must be at least 34" (86.4 cm) above the floor and no higher than 96" (2.4 m) from the bottom of the washer.

Floor drain system (view D) The floor drain system requires a siphon break that may be

purchased separately. See "Alternate Parts." The siphon break must be a minimum of 28" (71 cm) from the

bottom of the washer. Additional hoses might be needed.

E ect ca R< s 'sments

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is also recommended that a separate circuit serving only this appliance be provided.

To minimize possible shock hazard, the cord must be plugged into a mating, 3 prong, ground-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualified electrician.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

Do not ground to a gas pipe. Check with a qualified electrician if you are not sure the

washer is properly grounded.

• Do not have a fuse in the neutral or ground circuit.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected washer/dryer: This washer/dryer must be grounded. In the event of

malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This washer/dryer is equipped with a cord

having an equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with

all local codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or

personnel if you are in doubt as to whether the washer/dryer

is properly grounded. Do not modify the plug provided with the washer/dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

_ S ____,_ °_ o

...._c_,_,_U_ _s"__ _

Explosion Hazard

Use a new CSA international approved gas supply line.

install a shut-off valve,

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 13" (33 cm) water

column,

Examples of a qualified person include: licensed heating personnel,

authorized gas company personnel, and authorized service personnel. •

Failure to de so can result in death, explosion, or fire. •

Gas type

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54.

Natural Gas: This laundry center is equipped for use with Natural gas, It is

design-certified by CSA International for LP (propane or butane) gases with appropriate conversion.

• Your laundry center must have the correct burner for the type of gas in your home. Burner information is located on the rating plate in the door well of your dryer. If this information does not agree with the type of gas available, contact your

local Sears store or Sears Service Center.

LP gas conversion: Conversion must be made by a qualified technician. No attempt shall be made to convert the appliance from the gas

specified on the model/serial rating plate for use with a different gas without consulting your gas company,

Gas supply line

• 1/2"IPS pipe is recommended,

• 3/8"approved tubing is acceptable for lengths under 20 ft (6,1 m) if local codes and gas supplier permit.

• Lengths over 20 ft (6,1 m) should use larger tubing.

• Must include W' NPT minimum plugged tapping accessible for test gauge connection, immediately upstream of the gas

supply connection to the dryer (see illustration).

• Gas supply line coupling must be 34" (86.4 cm) to 37" (94 cm) from the floor.

Must include a shutoff valve: An individual shutoff valve must be installed within six (6)feet

(1.8 m) of the laundry center in accordance with the National Fuel Gas Code, ANSI Z223.1. The location should be easy to reach for opening and closing.

--A

_-- B

--C

A. Gas shutoff valve B. Vs" NPT minimum plugged tapping

C. Y/' NPT gas supply line D. Gas supply line coupling 34" (86.4 cm) min.

to 37" (94 cm) max. from floor

If you are using Natural gas, do not use copper tubing. If your laundry center has been converted to use LP gas,

%" LP compatible copper tubing can be used. If the total length of the supply line is more than 20 ft (6.1 m), use larger tubing.

Pipe joint compounds that resist the action of LP gas must be used. Do not use TEFLON °t tape.

Dryer gas connection

• This laundry center is equipped with its own permanent, flexible gas connector, design-certified by CSA International,

for connecting the laundry center to the gas supply line.

Flexiblegas connector

Burner input requirements

Elevations up to 10,000 ft (3,048 meters):

• The design of this laundry center is certified by CSA International for use at altitudes up to 10,000 ft (3,048 m) above sea level at the B.T.U. rating indicated on the model/ serial number plate. Burner input adjustments are not required when the dryer is operated up to this elevation.

Elevations above 10,000 ft (3,048 meters):

• When installed above 10,000 ft (3,048 m) a 4% reduction of the burner B.T.U. rating shown on the model/serial number plate is required for each 1,000 ft (305 m) increase in

elevation.

t®TEFLON is a registered trademark of EJ. Du Pont De Nemours and Company.

Gas Supply Pressure Testing

• The laundry center must be disconnected from the gas supply piping system during pressure testing at pressures

greater than 1/2psi.

Fire Hazard

Use a heavy metal vent. Do not use a plastic vent.

Do not use a metal foil vent. Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this laundry center

MUST BE EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, or a concealed space of a building.

If using an existing vent system

• Rigid metal vent is recommended to avoid crushing and kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for cleaning.

• Flexible metal vent must be fully extended and supported when the laundry center is in its final position.

• Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor performance.

• Do not install flexible metal vent in enclosed walls, ceilings or floors.

Elbows

45° elbows provide better airflow than 90° elbows.

Good Bet_r

Clamps

• Use clamps to seal all joints.

• Exhaust vent must not be connected or secured with screws or other fastening devices that extend into the interior of the

duct. Do not use duct tape.

• Clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint.

• Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.

• Review Vent system chart. Modify existing vent system if necessary to achieve the best drying performance.

If this is a new vent system

Vent material

• Use a heavy metal vent. Do not use plastic or metal foil vent.

• 4" (10.2 cm) heavy metal exhaust vent and clamps must be used. DURASAFF Mventing products are recommended.

4" (10.2cm)heavymetal exhaust vent

DURASAFE TMvent products can be purchased from your dealer. For further information, please call

1-800-4-MY-HOME ®(1-800-469-4663) or visit our website at www.sears.com.

Rigid metal vent

• For best drying performance, rigid metal vents are recommended.

Clamp

Exhaust

Recommended hood styles are shown here.

(10.2 cm)

A. Louvered hood style

B. Box hood style

The angled hood style (shown here) is acceptable.

(10.2 cm)__

An exhaust hood should cap the vent to keep rodents and insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.).

• Do not use an exhaust hood with a magnetic latch.

Improper venting can cause moisture and lint to collect indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint,

wallpaper, carpets, etc.

[] Housecleaning problems and health problems.

Excessive Weight Hazard

Use two or more people to move and install washer/dryer.

Failure to do so can result in back or other injury.

To protect the floor, use a large flat piece of cardboard from the shipping carton. Gently place the laundry center on its side, on

the cardboard.

Install the rear leveling legs

1. Push legs into holes in rear corners until they snap into place.

2. Check adjustability of rear legs by pushing in one leg. The other leg should come out. Check both legs. If they do not move freely, repeat Step 1.

Install the front leveling legs

1. Examine the front leveling legs. Find the diamond marking.

2. Screw front legs by hand, into the holes in the triangular braces in the front corners. Use wrench to finish turning the legs until the diamond marking is no longer visible.

For mobile home use Laundry centers with gas dryers must be securely fastened to the

floor.

Mobile home installations require a Mobile Home Installation Kit. See "Tools and Parts" section for ordering information.

1. Open the washer lid. The latch under the dryer will keep the lid open.

2. Pull the foam packing ring out of the washer.

NOTE: Keep the foam ring and use it when transporting your laundry center. This packing material is used to keep the washer

tub stable during transport.

C_ _ D_

Proper connection of the drain hose protects your floors from damage due to water leakage. To keep the drain hose from

coming off or leaking, it must be installed according to the

following instructions:

IMPORTANT: To ensure proper installation, this procedure must be followed exactly.

1. Check the drain hose to see whether it is the proper length.

2. Wet the inside of the straight end of the drain hose with tap wate£

IMPORTANT: Do not use any lubricant other than water.

3. Squeeze ears of the silver, double-wire clamp with pliers to open. Place clamp over the straight end of the drain hose

1A"(6.4 mm) from the end.

3. Stand the laundry center upright.

(6.4 turn)

Open clamp. Twist hose back and forth while pushing onto drain connector on the side of the laundry center. Continue until hose contacts the ribbed stops on the cabinet.

5. Place clamp over the area marked "CLAMR" Release clamp.

For laundry tub or standpipe drain systems

1. Open the yellow, single-wire clamp and slide over the hooked

end of the drain hose to secure the rubber and corrugated sections together.

A. Hooked end B. Drain hose

Using pliers, tighten the couplings with an additional two- thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

Clear the water lines

• Run water through both faucets and inlet hoses, into a laundry tub, drainpipe or bucket to get rid of particles in the water lines that might clog the inlet valve screens.

• Check the temperature of the water to make sure that the hot water hose is connected to the hot water faucet and that the

cold water hose is connected to the cold water faucet.

Connect the inlet hoses to the washer

1. Attach the hot water hose to the bottom inlet valve. Attaching the hot water hose first makes it easier to tighten connection

with pliers.

2. Screw on coupling by hand until it is seated on the washer.

3. Using pliers, tighten the couplings with an additional two- thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

2. Put the hooked end of drain hose into laundry tub or standpipe. Rotate hook to eliminate kinks.

To keep drain water from going back into the washer:

• Do not straighten hooked end of the drain hose and force excess drain hose into standpipe. Hose should be secure but loose enough to provide a gap for air.

• Do not lay excess hose on the bottom of the laundry tub.

For use with floor drain Remove the drain hose hook from the corrugated drain hose. You

may need additional parts. See Floor drain under "Alternate Parts."

Insert a new flat washer (supplied) into each end of the inlet hoses. Firmly seat the washers in the couplings.

A B

A. Coupling

B. Washer

Connect the inlet hoses to the water faucets

Make sure the washer basket is empty.

2. Attach the hose labeled hot to the hot water faucet. Screw on coupling by hand until it is seated on the washer.

3. Attach the hose labeled cold to the cold water faucet. Screw on coupling by hand until it is seated on the washer.

A. Cold water inlet valve (top)

B. Hot water inlet valve (bottom)

1. Attach the cold water hose to the top inlet valve.

2. Screw on coupling by hand until it is seated on the washer.

3. Using pliers, tighten the couplings with an additional two- thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

If you are working in a closet or recessed area Move the laundry center into its final position and remove

cardboard from under laundry center. Remove the access panel by removing 3 Phillips-head screws and one bumper, located at

the top of the access panel. Set panel, screws, and bumper aside. Complete hookup of water hoses and (on gas models) the

flexible gas connector through the access area. Replace access panel upon completion of laundry center installation.

Check for leaks

4. Turn on the water faucets and check for leaks. A small amount of water might enter the washer. You will drain this

later.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement dates for

future reference.

• If you connect only one water hose, you must cap off the remaining water inlet port.

• Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.

• The apparatus must be connected to the water faucets using the new hoses. Do not use old hoses.

Move the laundry center to its final location and remove any cardboard used to move the laundry center.

Locate the plastic strap included in the parts package.

Beaded tie strap

Wrap the drain hose to the laundry tub leg or standpipe with the plastic strap (A or B below) and secure.

Choose your exhaust installation type

Recommended exhaust installations

Typical installations vent the dryer fromthe rear of the washer/

dryer. Other installations are possible.

A I ......D

............... H

A. Dryer E. Elbow B. Rigid metal or flexible metal E Clamps

vent G. Elbow

C. Clamps H. Exhaust hood D. Waft

Ifthe water faucets and the drain standpipe are recessed, put the hooked end of the drain hose in the standpipe. Tightly wrap the plastic strap around the water inlet hoses and the drain hose (C above).

Optional exhaust installations

This laundry center can be converted to exhaust out the right or

left side. To convert the laundry center, use Side Exhaust Kit Part Number 279823. If your laundry center was previously exhausted

from the right or left side, it can be converted to rear exhaust by

using standard offset connections. To cover the hole in the side, one of the following plugs can be added:

692790 (white) 3979370 (graphite) 3977784 (biscuit)

Follow the instructions in the kit to install. Kits are available from

your local Sears store or Sears Service Center.

A B C

A. Standard rear offset exhaust installation

B.Rear exhaust for offset close clearanceconnection C.Left or right side exhaust installation

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for your installation. Three close-clearance installations are shown.

Refer to the manufacturer's instructions provided with the vent system.

A. Loop system with standard elbows B. Loop system with one offset and one standard elbow C. Vent system with one periscope (2" [5 cm] clearance)

NOTE: The following kits for close clearance alternate installations are available for purchase. To order, please call

1-800-4-MY-HOME ®(1-800-469-4663).

• Over-the-Top Installation: Part Number 26-49900

• Periscope Installation (For use with dryer vent to wall vent mismatch):

Part Number 26-49901 - Less than 5" (12.7 cm) mismatch Part Number 26-49908 - 5" (12.7 cm) to 18" (45.7 cm)

mismatch Part Number 26-49904 - 18" (45.7 cm) to 29" (73.7 cm)

mismatch Part Number 26-49905 - 29" (73.7 cm) to 50" (127 cm)

mismatch

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate

beneath the mobile home. Terminate the exhaust vent outside.

Determine vent path

• Select the route that will provide the straightest and most direct path outdoors.

• Plan the installation to use the fewest number of elbows and turns.

• When using elbows or making turns, allow as much room as possible.

• Bend vent gradually to avoid kinking.

• Use the fewest 90 ° turns possible.

Determine vent length and elbows needed for best drying performance

• Use the Vent system chart below to determine type of vent material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust systems longer than those

specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and

increased energy usage.

The Vent system chart provides venting requirements that will help to achieve the best drying performance.

Vent system chart NOTE: Side exhaust adds a 90° turn inside the laundry center. To

determine maximum exhaust length, add one 90° turn to the chart.

Number of Type of Vent Box or Angled 90° turns Louvered hoods

or elbows hoods

0 Rigid metal 43 ft (13.1 m) 36 ft (11.0 m)

Flexible metal 30 ft (9.1 m) 24 ft (7.3 m)

1 Rigid metal 33 ft (10.1 m) 26 ft (7.9 m)

Flexible metal 24 ft (7.3 m) 18 ft (5.5 m)

2 Rigid metal 24 ft (7.3 m) 16 ft (4.9 m)

Flexible metal 16 ft (4.9 m) 10 ft (3.0 m)

1. Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

3. Run vent to dryer location. Use the straightest path possible. See "Determine vent path" in "Plan Vent System." Avoid 90°

turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the interior

of the vent to secure vent.

Properly leveling your laundry center averts excessive noise and vibration.

1. Check the levelness of the laundry center by placing a level on the top edge of the washer, first side to side, then front to

back.

Ifthe laundry center is not level, prop up the front with a wood block and adjust the feet up or down as necessary. Remove wood block and lower laundry center. Repeat this step until the laundry center is level.

Remove the red cap from the flexible gas connector.

Remove the V2"NPT adapter from the flexible gas connector. (It will be necessary to use two adjustable wrenches.)

Install the adapter on the V2" rigid gas supply pipe using pipe-joint compound.

6. Open the shutoff valve in the supply line. The valve is open when the handle is parallel to the gas pipe.

A.Closed valve B.Open valve

Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in laundry center. If connecting to existing vent, make sure the

vent is clean. The vent must fit over the exhaust outlet and inside the exhaust hood. Make sure the vent is secured to

exhaust hood with a 4" (10.2 cm) clamp.

2. Move laundry center into its final position. Do not crush or kink vent. Make sure laundry center is level.

3. Check to be sure there are no kinks in the flexible gas line.

A B _

E .................._

A. _2"rigid gas supply pipe

B.Usepipe-joint compound. C. _*"NPTadapter D. Do not usepipe-joint compound.

E.Flexiblegas connector

NOTE: For LP gas connections, you must use pipe-joint compound resistant to the action of LP gas. Do not use TEFLON ®tape.

Attach the flexible gas connector to the V2" NPT adapter. Do not use pipe-joint compound for this connection.

There should be a natural loop in the flexible gas connector. The flexible gas connector must not be twisted, kinked or attached with any sharp bends.

CORRECT

5. All connections must be wrench tightened.

1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials. Keep the plastic foam for use if the laundry center should be transported.

4. Check the laundry center's final location. Be sure the vent is not crushed or kinked.

5. Check that the laundry center is level and front leveling feet are tight. See "Level Laundry Center."

6. Plug into a grounded 3 prong outlet. Turn power on.

7. Check that the water faucets are on.

8. Check for leaks around faucets and inlet hoses.

9. Remove the blue protective film on the console and any tape remaining on the laundry center.

10. Read "Washer Use" and "Dryer Use."

11. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.

12. To test the washer, measure 1/2the normal recommended amount of detergent and pour it into the washer. Close the lid.

Select HEAVY DUTY and pull out the Cycle Control knob. Allow the washer to complete one whole cycle.

13. To test the dryer, set the dryer on a full heat cycle (not an air cycle) for 20 minutes and start the dryer.

If the dryer will not start, check the following:

• Laundry Center is plugged into a grounded 3 prong

outlet.

• Start button has been firmly pushed.

• Electrical supply is connected.

• House fuse is intact and tight, or circuit breaker has not

tripped.

• Dryer door is closed.

14. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you do not feel heat, turn the

dryer off and check to see whether the gas supply line shutoff valve is open.

• If the gas supply line shutoff valve is closed, open it, then

repeat the 5-minute test as outlined above.

• If the gas supply line shutoff valve is open, contact a

qualified technician.

WASHER USE

HEAVY DUTY SHORT

SPIN 10 REGULAR

GENTLE WATERTEMP WATERLEVEL

RINSE PERMANENT MEOIUM

PRESS COLD WARM SMALL LARGE

SHORT O--

REGULAR10 SPiN

SUPER 12

KN|T/DELJCATE

RINSE

SOAK_

Fire Hazard

Never place items in the washer that are dampened with gasoline or other flammable fluids.

No washer can completely remove oil. Do not dry anything that has ever had any type of oil on

it (including cooking oils). Doing so can result in death, explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

The following is a guide to starting your washer. Periodic references to other sections of this manual provide more detailed information.

1. Pour measured powdered or liquid detergent into the washer. Ifdesired, add powdered or liquid color safe bleach.

2. Place a load of sorted clothes in the washer.

• Load evenly to maintain washer balance. Mix large and small items. See "Loading."

• Items should move easily through the wash water. Overloading can cause poor cleaning.

3. Close the washer lid.

4. Turn the WATER LEVEL selector knob to the correct setting for your wash load and the type of fabric being washed.

WATER LEVEL

MEDIUM

[0A0

SMALL LARGE

_ESET

LOA_LOAOo O

WARM WARM LOAD

e o LOAD LOAD

COLD HOT o ®

C0L0 C0LO

• Choose a load size that allows the load to move freely for best fabric care. See "Loading."

• You may change the load size selection after the washer has started filling by turning the selector to a different setting.

Set the WATER TEMP selector to the correct setting for the type of fabric and soils being washed.

Use the warmest water safe for the fabric. Follow garment label instructions.

Water Temp Use For

Hot Whites and pastels

Warm Bright colors

Cold Colors that bleed or fade

NOTE: In wash water temperatures colder than 60°F (15.6°C), detergents do not dissolve well. Soils can be difficult to

remove. Some fabrics can retain wear wrinkles and have increased pilling (the formation of small lint-like balls on the

surface of garments).

Push in the Cycle Control knob and turn it clockwise to the wash cycle you want. Pull out the Cycle Control knob to start

the washer.

To stop or restart your washer:

• To stop the washer at any time, push in the Cycle Control knob.

• To restart the washer, close the lid (if open) and pull out the Cycle Control knob.

RESET

WATER TEMP

WARM WARM

COLD WARM

COLD e • ffOT

COLic C_LD

Heavy soils

Moderate to light soils

Light soils

This section describes the available wash cycles and will help you make the best cycle selections for your wash loads. Each cycle is designed for different types of fabric and soil levels.

• The washer pauses briefly throughout each cycle. These pauses are normal. Refer to "Normal Sounds" for sounds you may hear during a wash cycle.

• Refer to "Understanding Washer Cycles" to learn what happens during a wash cycle.

HEAVY DUTY

RINSE

SPIN 10 REGULAR

8 GENTLE

PERMANENT PRESS

RINSE

KNIT/DELICATE

SOAK

Heavy Duty

Use this cycle for sturdy or heavily soiled loads. Wash combines fast-speed agitation and fast-spin speeds.

• Use the Super or Regular settings for heavily soiled and sturdy fabrics.

• Use the Short setting for light soil and sturdy fabrics.

Permanent Press

The Permanent Press Cycle includes a load-cooling process that reduces wrinkling. Wash combines fast and slow-speed agitation and slow spin speeds.

When the timer reaches Pause, the washer will drain and pause for approximately 2 minutes while some of the wash water is drained and replaced with rinse water.

Knit/Delicate

Use this cycle for lingerie and loosely knit items. Partway through the cycle the washer pauses and soaks the load for more gentle care of lightly soiled delicate items. Wash combines slow-speed agitation for gentle soil removal and slow spin speeds to reduce wrinkling.

Soak The Soak cycle features 4 minutes of agitation followed by an

unlimited soak time to help remove heavy soils and stains that need pretreatment. You will need to reset the washer to a SPIN setting to remove water.

• The Soak cycle should be followed by the Heavy Duty or Permanent Press or Prewash cycle with additional detergent.

NOTE: Hot water is not recommended for soaking. It may set some stains.

Prewash

Use this cycle to get up to 4 minutes of agitation to help remove heavy soils and stains that need pretreatment.

• The Prewash cycle should be followed by the Heavy Duty or Permanent Press cycle with additional detergent.

When using extra detergent for heavily soiled clothes, or washing special-care items, you may find an extra rinse and spin is

needed.

1. Push in the Cycle Control knob and turn it clockwise to any of the RINSE settings.

• For fast agitation and spin, use the Heavy Duty cycle.

• For slow agitation and spin, use the Permanent Press

cycle.

2. Set the WATER LEVEL and WATER TEMP controls to the desired setting.

3. Pull out the Cycle Control knob. The washer fills to the selected load size, agitates, drains, and spins.

A drain and spin may help shorten drying times for some heavy fabrics or special-care items by removing excess water.

1. Push in the Cycle Control knob and turn it clockwise to any of the SPIN settings.

• For a fast spin, use the Heavy Duty cycle.

• For a slow spin, use the Permanent Press cycle.

2. Pull out the Cycle Control knob. The washer drains, then spins.

+ 39 hidden pages