Kenmore 11098752793 Owner’s Manual
®
24-1nch Wide
LAUNDRY CENTER
Washer - Gas Dryer
f
CENTRO DE LAVANDERIA
de 24 pulg. (61 cm) de ancho
Lavadora - Secadora a gas
\
3979333A Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com
TABLE OF CONTENTS
WARRANTY
WARRANTY .................................................................................... 2
WASHER/DRYER SAFETY ............................................................ 3
INSTALLATION INSTRUCTIONS .................................................. 5
Tools and Parts ............................................................................ 5
Alternate Parts.............................................................................. 5
Location Requirements ............................................................... 5
DrainSystem ................................................................................ 7
Electrical Requirements ............................................................... 7
Gas Supply Requirements ........................................................... 8
Venting Requirements .................................................................. 9
Install Leveling Legs ..................................................................... 9
Remove Foam Packing .............................................................. 10
Connect Drain Hose ................................................................... 10
Connect Inlet Hoses ................................................................... 10
Secure the Drain Hose ............................................................... 11
Plan Vent System ....................................................................... 11
Install Vent System ..................................................................... 13
Level Laundry Center ................................................................. 13
Make Gas Connection ............................................................... 13
Connect Vent.............................................................................. 14
Complete Installation ................................................................. 14
FEATURES AND BENEFITS ........................................................ 14
DUAL-ACTION TMPlus Agitator .................................................. 14
Porcelain Wash Basket .............................................................. 14
4-way Venting ............................................................................ 14
WASHER USE ............................................................................... 15
Starting Your Washer ................................................................. 15
Cycles ......................................................................................... 16
Rinse and Spin ........................................................................... 16
Drain and Spin............................................................................ 16
Understanding Washer Cycles .................................................. 16
Normal Sounds .......................................................................... 17
LAUNDRY TIPS ............................................................................ 17
Loading ....................................................................................... 17
DRYER USE .................................................................................. 18
Starting Your Dryer..................................................................... 18
Stopping and Restarting ............................................................ 18
Loading ....................................................................................... 19
Drying, Cycle and Temperature Tips ......................................... 19
Cycles ......................................................................................... 19
LAUNDRY CENTER CARE .......................................................... 20
Cleaning Your Washer ............................................................... 20
Water Inlet Hoses ....................................................................... 20
Cleaning the Lint Screen ............................................................ 20
Cleaning the Dryer Interior ......................................................... 21
Removing Accumulated Lint ...................................................... 21
Vacation, Storage, and Moving Care ......................................... 21
TROUBLESHOOTING WASHER ................................................. 22
TROUBLESHOOTING DRYER .................................................... 24
WE SERVICE WHAT WE SELL .................................................... 25
Full One-Year Warranty on mechanical and electrical parts
For one year from the date of purchase, when this laundry center
is installed and operated according to the instructions provided in
this Use and Care Guide, Sears will repair this laundry center, free
of charge, if defective in material or workmanship.
NOTE: Exhausting your laundry center with a plastic vent can
void this warranty. See "Installation Instructions" for the complete
exhaust requirements for this laundry center.
Limited Five-Year Warranty on Gearcase Parts
For the second through fifth years from the date of purchase,
Sears will replace any gearcase parts that are defective in
material or workmanship. You will be charged for labor after the
first year.
Limited Ten-Year Warranty on Plastic Tub
For the second through tenth years from the date of purchase,
Sears will replace the plastic tub if defective in material or
workmanship. You will be charged for labor after the first year.
Warranty Restriction
If the laundry center is subject to other than private family use,
the above warranty coverage is effective for only 90 days.
Warranty Service
Warranty service is available by contacting the nearest Sears
Service Center. This warranty applies only while the product is in
use in the United States.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
For Sears warranty information or to contact a Sears Service
Center, please reference the service numbers located on the
back page of this manual.
Sears, Roebuck and Co.
D/817WA, Hoffman Estates, IL 60179
Product Record
In the space below, record your complete model number, serial
number, and purchase date. You can find this information on the
model and serial number label, located at the top inside dryer
door well.
Have this information available to help you quickly obtain
assistance or service when you contact Sears concerning your
appliance.
Model number
Serial number
Purchase date
Save these instructions and your sales receipt for future
reference.
2
WASHER/DRYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or
This is the safety alert symbol.
"WARNING." These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
WARNING: For your safety, the information in this manual must be followed to minimize I
the risk of fire or explosion, or to prevent property damage, personal injury, or death. I
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Clear the room, building, or area of all occupants.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency, or
the gas supplier.
IM PORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer/dryer, follow
basic precautions, including the following:
Read all instructions before using the washer/dryer.
Do not place items exposed to cooking oils in
your dryer. Items contaminated with cooking oils
may contribute to a chemical reaction that could
cause a load to catch fire.
Do not wash or dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, other flammable,
or explosive substances as they give off vapors
that could ignite or explode.
Do not add gasoline, dry-cleaning solvents, or other
flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
• Do not allow children to play on or in the washer/dryer. •
Close supervision of children is necessary when
the washer/dryer is used near children.
• Before the washer/dryer is removed from service or •
discarded, remove the doors to the washer/dryer
compartments.
• Do not reach into the washer/dryer if the tub, agitator
or drum is moving.
• Do not install or store the washer/dryer where it will be
exposed to the weather.
• Do not tamper with controls.
• Clean dryer lint screen before or after each load.
Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for 2 weeks or more. HYDROGEN GAS iS
EXPLOSIVE. If the hot water system has not been
used for such a period, before using the washing
machine, turn on all hot water faucets and let the
water flow from each for several minutes. This will
release any accumulated hydrogen gas. As the gas
is flammable, do not smoke or use an open flame
during this time.
Do not repair or replace any part of the washer/dryer
or attempt any servicing unless specifically recom-
mended in this Use and Care Guide or in published
user-repair instructions that you understand and have
the skills to carry out.
Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of
the fabric softener or product.
Do not use heat to dry articles containing foam rubber
or similarly textured rubberqike materials.
Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint,
dust, and dirt.
• The interior of the machine and dryer exhaust vent
should be cleaned periodically by qualified service
personnel.
• See "Electrical Requirements" for grounding
instructions.
SAVE THESE INSTRUCTIONS
IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National
Fuel Gas Code, ANSI Z223.1/NFPA 54.
The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70.
4
INSTALLATION
INSTRUCTIONS
Check that you have everything necessary for correct installation.
Proper installation is your responsibility.
Parts listed are available from your local Sears store or Sears
Service Center. Please reference the service numbers located on
the back page of this manual.
If You Have You Will Need to Buy
Laundry tub or Sump pump system (if not already
standpipe taller than available)
96 in. (2.4 m)
Tools needed:
• 8in. or lOin. adjustable • Knife
wrench (for gas
connections) • Safety glasses
• Flat-blade screwdriver • Duct tape
• Adjustable wrench that • Pipe-Joint compound
opens to 1 in. (2.5 cm) or resistant to L.R gas
9/16in. open-end wrench • Caulking gun and
(for adjusting dryer feet) compound (for installing
• Level new exhaust vent)
• ¼ in. nut driver or socket • Gloves
wrench • Pliers
• Wood block (for leveling) • Ruler or measuring tape
• Tin snips(new vent
installation)
Parts supplied
Remove parts package from the washer basket. Check that all
parts were included.
1 in. (2.5 cm) 2 in. (5 cm) diameter to 1 in. (2.5 cm)
diameter standpipe diameter standpipe adapter, Part
Number 3363920
Overhead sewer Standard 20 gal. (76 L) 34 in. (86.4 cm)
tall drain tub or utility sink and sump
pump (available from local plumbing
suppliers)
Floor drain Siphon break, Part Number 285320,
additional drain hose, Part Number
285702 and connector kit,
Part Number 285442
Drain hose too short Drain hose, Part Number 285664 and
connector kit, Part Number 285442
Lint clogged drain Drain protector, Part Number 367031
Water faucets 2 longer water fill hoses:
beyond reach of fill 6 ft (1.8 m) Part Number 76314,
hoses 10 ft (3.0 m) Part Number 350008
L }cst ©_'1_,@(;_,, y@'_sx?yl1:,s
5
1. Water inlet hoses (2)
2. Inlet hose flat washers (4)
3. Rear leveling legs (2)
4. Front leveling legs (2)
Parts needed:
Check local codes and with gas supplier, check existing gas
supply, electrical supply and venting, and read "Electrical
Requirements," "Gas Supply Requirements" and "Venting
Requirements" before purchasing paris.
Mobile home installations require:
• Mobile Home Installation Kit. To order, call your local Sears
store or Sears Service Center. For further information, please
reference the service numbers located on the back page of
this manual. Ask for Part Number 346764.
• Metal exhaust system hardware available for purchase from
your local Sears store or Sears Service Center.
7
5. Plastic strap
6. Drain hose
7. Yellow, single wire hose clamp
8. Silver, double-wire hose clamp
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Failure to do so can result in death, explosion,
or fire.
You will need
• A location that allows for proper exhaust installation. A gas
laundry center must be exhausted to the outdoors. See
"Venting Requirements."
• Agroundedelectricaloutletlocatedwithin2ft (61cm)of Minimum installation spacing for recessed area or closet
either side of the laundry center. See "Electrical installation
Requirements."
• A sturdy floor to support the laundry center weight (laundry
center, water and load) of 500 Ibs (226.8 kg).
• A level floor with a maximum slope of 1 in. (2.5 cm) under
entire laundry center. Clothes may not tumble properly and
automatic sensor cycles may not operate correctly if dryer is
not level. Installing on carpet is not recommended.
• A water heater set to deliver 120°F (49°C) water to the
washer.
• Hot and cold water faucets located within 4 f_ (1.2 m) of the
hot and cold water fill valves, and water pressure of 5-100 psi
(34.5-689.6 kPa).
Install the laundry center where it is protected from water and/or
weather.
Do not operate your washer in temperatures at or below 32°F
(O°C). Some water can remain in the washer and can cause
damage in low temperatures. See "Vacation, Storage, and
Moving Care" for winterizing information.
Do not operate your dryer at temperatures below 45°F (7°C). At
lower temperatures, the dryer might not shut off at the end of an
automatic cycle. This can result in longer drying times.
Check code requirements. Some codes limit, or do not permit,
installation of the laundry center in garages, closets, mobile
homes, or sleeping quarters. Contact your local building
inspector.
NOTE: No other fuel-burning appliance can be installed in the
same closet as a dryer.
Installation Clearances
The location must be large enough to fully open the dryer door.
Laundry Center Dimensions
The following dimensions shown are for the minimum spacings
allowed.
• Additional spacing should be considered for ease of
installation and servicing.
Additional clearances might be required for wall, door and
floor moldings.
Additional spacing of 1 in. (2.5 cm) on all sides of the dryer is
recommended to reduce noise transfer.
For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
Rear clearance may be 0 in. when house exhaust system is
lined up directly with dryer exhaust.
(1_1 _ _t
a' _.eml
1 2
1. Recessed Area
2. Side view - closet or confined area
3. Closet door with vents
Mobile Home-Additional Installation Requirements
This laundry center is suitable for mobile home installations.
The installation must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280).
Mobile home installations require:
• Metal exhaust system hardware which is available for
purchase from your local Sears store or Sears Service Center.
• Mobile Home Installation Kit Part Number 346764. See "Tools
and Parts" section for ordering information.
• Special provisions must be made in mobile homes to
introduce outside air into the dryer. The opening (such as a
nearby window) should be at least twice as large as the dryer
exhaust opening.
* Most installations require a minimum 51/2in. (14 cm) clearance
behind the dryer for the exhaust vent with elbow. See "Venting
Requirements."
6
The laundry center can be installed using the standpipe drain
system (floor or wall), the laundry tub drain system, or the floor
drain system. Select the drain hose installation method you need
(see "Alternate Parts").
Standpipe drain system - wall or floor (view 1 & 2)
The standpipe drain requires a minimum diameter standpipe of 2
in. (5 cm). The minimum carry-away capacity can be no less than
17 gal. (64 L) per minute. A 2 in. (5 cm) diameter to 1 in. (2.5 cm)
diameter standpipe adapter kit is available. See "Alternate Parts."
The top of the standpipe must be at least 39 in. (99 cm) high and
no higher than 96 in. (2.4 m) from the bottom of the washer.
1 2
Laundry tub drain system (view 3)
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top
of the laundry tub must be at least 34 in. (86.4 cm) above the floor
and no higher than 96 in. (2.4 m) from the bottom of the washer.
Floor drain system (view 4)
The floor drain system requires a siphon break that may be
purchased separately. (See "Alternate Parts.")
The siphon break must be a minimum of 28 in. (71 cm) from the
bottom of the washer. Additional hoses might be needed.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
A 120-volt, 60-Hz., AC-only, 15- or 20-ampere, fused
electrical supply is required. Time-delay fuse or circuit
breaker is recommended. It is also recommended that a
separate circuit serving only this appliance be provided.
To minimize possible shock hazard, the cord must be
plugged into a mating, 3 prong, ground-type outlet, grounded
in accordance with local codes and ordinances. If a mating
outlet is not available, it is the personal responsibility and
obligation of the customer to have the properly grounded
outlet installed by a qualified electrician.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
Do not ground to a gas pipe.
Check with a qualified electrician if you are not sure the
washer is properly grounded.
Do not have a fuse in the neutral or ground circuit.
GROUNDING INSTRUCTIONS
• For a grounded, cord-connected washer/dryer:
This washer/dryer must be grounded. In the event of mal-
function or breakdown, grounding will reduce the risk of
electric shock by providing a path of least resistance for
electric current. This washer/dryer is equipped with a cord
having an equipment-grounding conductor and a grounding
4
plug. The plug must be plugged into an appropriate outlet
that is properly installed and grounded in accordance with
all local codes and ordinances.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative or
personnel if you are in doubt as to whether the washer/dryer
is properly grounded. De not modify the plug provided with
the washer/dryer: if it will not fit the outlet, have a proper
outlet installed by a qualified electrician.
SAVE THESE INSTRUCTIONS
Explosion Hazard
Use a new AGA or CSA approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make
sure gas pressure does not exceed 13" (33 cm)
water column=
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion,
or fire.
Gas Type
Natural Gas:
This laundry center is equipped for use with NATURAL GAS. It is
design-certified by CSA International for L.R (propane or butane)
gases with appropriate conversion.
• Your laundry center must have the correct burner for the type
of gas in your home. Burner information is located on the
rating plate in the door well of your dryer. If this information
does not agree with the type of gas available, contact your
local Sears store or Sears Service Center.
L.P=gas conversion:
Conversion must be made by a qualified technician.
No attempt shall be made to convert the appliance from the gas
specified on the model/serial rating plate for use with a different
gas without consulting the serving gas supplier.
Gas Supply Line
• _/2in. IPS pipe is recommended
• 3/8in. approved tubing is acceptable for lengths under 20 ft
(6.1 m) if local codes and gas supplier permit.
• Lengths over 20 ft (6.1 m) should use larger tubing.
• Must include _/8in. NPT plugged tapping, immediately
upstream of the gas supply connection to the dryer
(see illustration).
• Gas supply line coupling must be 34 in. (86.4 cm) to 37 in.
(94 cm) from the floor.
Must include a shutoff valve:
An individual shutoff valve must be installed within six (6) feet
(1.8 m) of the laundry center in accordance with the National
Fuel Gas Code, ANSI Z223.1. The location should be easy to
reach for opening and closing.
1
2
3
1. Gas shutoff valve
2. V8in. NPT plugged tapping
3. _/2in. NPT gas supply line
4. Gas supply line coupling 34 in, (86,4 cm) min.
to 37 in, (94 cm) max. from floor
If you are using natural gas, do not use copper tubing.
If your laundry center has been converted to use L.R gas, %
in. L.R compatible copper tubing can be used. If the total
length of the supply line is more than 20 ft (6.1 m), use larger
tubing.
NOTE: Pipe joint compounds that resist the action of L.R gas
must be used. Do not use TEFLON _ tape.
Dryer Gas Connection
• This laundry center is equipped with its own permanent,
flexible gas connector, design-certified by CSA International,
for connecting the laundry center to the gas supply line.
uu_
Flexible gas connector
Burner Input Requirements:
Elevations up to 10000 feet (3,048 meters):
• The design of this laundry center is certified by CSA
International for use at altitudes up to 16,000 ft (3,048 m)
above sea level at the B.T.U. rating indicated on the model/
serial number plate. Burner input adjustments are not
required when the dryer is operated up to this elevation.
Elevations above 10,000 feet (3,048 meters):
• When installed above 1O,OO0ft (3,048 m) a 4% reduction of
the burner B.T.U. rating shown on the model/serial number
plate is required for each 1,000 ft (365 m) increase in
elevation.
8
Loading...