Kenmore 11098752792 Owner’s Manual
®
24-1nch Wide (61 cm)
LAUNDRY CENTER
Washer - Gas Dryer
CENTRO DE LAVANDERIA
de 24 pulg. (61 cm) de ancho
Lavadora - Secadora a gas
J
\
!
L_ "_ "_ "_"L
3979333B Sears Roebuck and Co,, Hoffman Estates, IL 60t 79 U,S,A. www.sears,com
TABLE OF CONTENTS
WARRANTY
WARRANTY ..................................................................................... 2
WASHER/DRYER SAFETY ............................................................ 3
INSTALLATION INSTRUCTIONS .................................................. 5
Tools and Parts ............................................................................ 5
Alternate Parts .............................................................................. 5
Location Requirements ............................................................... 5
Drain System ................................................................................ 7
Electrical Requirements ................................................................ 7
Gas Supply Requirements ........................................................... 8
Venting Requirements .................................................................. 9
Install Leveling Legs ..................................................................... 9
Remove Foam Packing ............................................................. 10
Connect Drain Hose .................................................................. 10
Connect Inlet Hoses .................................................................. 10
Secure Drain Hose .................................................................... 11
Plan Vent System ...................................................................... 11
Install Vent System .................................................................... 13
Level Laundry Center ................................................................ 13
Make Gas Connection ............................................................... 13
Connect Vent ............................................................................. 14
Complete Installation ................................................................. 14
FEATURES AND BENEFITS ....................................................... 14
DUAL-ACTION TM Plus Agitator ................................................. 14
Porcelain Wash Basket ............................................................. 14
4-way Venting ............................................................................ 14
WASHER USE .............................................................................. 15
Starting Your Washer ................................................................ 15
Cycles ........................................................................................ 16
Rinse and Spin .......................................................................... 16
Drain and Spin ........................................................................... 16
Understanding Washer Cycles .................................................. 16
Normal Sounds .......................................................................... 17
LAUNDRY TIPS ............................................................................ 17
Loading ...................................................................................... 17
DRYER USE ................................................................................. 18
Starting Your Dryer .................................................................... 18
Stopping and Restarting ........................................................... 18
Loading ...................................................................................... 19
Drying, Cycle and Temperature Tips ........................................ 19
Cycles ........................................................................................ 19
LAUNDRY CENTER CARE ......................................................... 20
Cleaning the Laundry Center Location ..................................... 20
Cleaning Your Washer ............................................................... 20
Water Inlet Hoses ...................................................................... 20
Cleaning the Lint Screen ........................................................... 20
Cleaning the Dryer Interior ........................................................ 21
Removing Accumulated Lint ..................................................... 21
Vacation, Storage, and Moving Care ........................................ 21
TROUBLESHOOTING WASHER ................................................ 22
TROUBLESHOOTING DRYER .................................................... 24
PROTECTION AGREEMENTS .................................................... 25
SERVICE NUMBERS ............................................... BACK COVER
Full One-Year Warranty on Mechanical and Electrical Parts
For one year from the date of purchase, when this laundry center
is installed and operated according to the instructions provided in
this Use and Care Guide, Sears will repair this laundry center, free
of charge, if defective in material or workmanship.
NOTE: Exhausting your laundry center with a plastic vent can
void this warranty. See "Installation Instructions" for the complete
exhaust requirements for this laundry center.
Limited Five-Year Warranty on Gearcase Parts
For the second through fifth years from the date of purchase,
Sears will replace any gearcase parts that are defective in
material or workmanship. You will be charged for labor after the
first year.
Limited Ten-Year Warranty on Plastic Tub
For the second through tenth years from the date of purchase,
Sears will replace the plastic tub if defective in material or
workmanship. You will be charged for labor after the first year.
Warranty Restriction
If the laundry center is subject to other than private family use,
the above warranty coverage is effective for only 90 days.
Warranty Service
Warranty service is available by contacting the nearest Sears
Service Center. This warranty applies only while the product is in
use in the United States.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
For Sears warranty information or to contact a Sears Service
Center, please reference the service numbers located on the
back page of this manual.
Sears, Roebuck and Co.
D/817WA, Hoffrnan Estates, IL 60179
Product Record
In the space below, record your complete model number, serial
number, and purchase date. You can find this information on the
model and serial number label, located at the top inside dryer
door well.
Have this information available to help you quickly obtain
assistance or service when you contact Sears concerning your
appliance.
Model number
Serial number
Purchase date
Save these instructions and your sales receipt for future
reference.
WASHER/DRYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages inthis manual and on your appliance. Always read and obey all
safety messages.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or
This is the safety alert symbol.
"WARNING." These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
I WARNING: For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, or to prevent property damage, personal injury, or death,
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Clear the room, building, or area of all occupants.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency, or
the gas supplier.
In the State of Massachusetts, the following installation instructions apply:
• Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or
licensed by the State of Massachusetts.
• If using a ball valve, it shall be a T-handle type.
• A flexible gas connector, when used, must not exceed 3 feet.
iiiiiiiiiii@i;iii
iMPORTANT SAFETY iNSTRUCTiONS
WARNUNG: To reduce the risk of fire, eHectric shock, or injury to persons when using the washer/dryer, follow
basic precautions, incHuding the following:
m Read aHinstructions before using the washer/dryer, m
m Do not pHaceitems exposed to cooking oiHsin
your dryer. Items contaminated with cooking oiHs
may contribute to a chemicaH reaction that couHd
cause a Hoadto catch fire.
m Do not wash or dry articles that have been previousHy
cleaned in, washed in, soaked in, or spotted with
gasoHine, dry-cleaning solvents, other flammable,
or explosive substances as they give off vapors
that could ignite or explode.
Do not add gasoline, dry-cleaning solvents, or other "
flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
,, Do not allow children to play on or in the washer/dryer.
Close supervision of children is necessary when
the washer/dryer is used near children.
,, Before the washer/dryer is removed from service or ,,
discarded, remove the doors to the washer/dryer
compartments.
,, Do not reach into the washer/dryer if the tub, agitator
or drum is moving.
Do not install or store the washer/dryer where it will be
exposed to the weather.
,, Do not tamper with controls.
" Clean dryer lint screen before or after each load.
Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not been
used for such a period, before using the washing
machine, turn on all hot water faucets and let the
water flow from each for several minutes. This will
release any accumulated hydrogen gas. As the gas
is flammable, do not smoke or use an open flame
during this time.
Do not repair or replace any part of the washer/dryer
or attempt any servicing unless specifically recom-
mended in this Use and Care Guide or in published
user-repair instructions that you understand and have
the skills to carry out.
Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of
the fabric softener or product.
Do not use heat to dry articles containing foam rubber
or similarly textured rubber like materials.
Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint,
dust, and dirt.
The interior of the machine and dryer exhaust vent
should be cleaned periodically by qualified service
personnel.
See "Electrical Requirements" for grounding
instructions.
SAVE THESE INSTRUCTmONS
IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National
Fuel Gas Code, ANSI Z223,1/NFPA 54,
The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70,
INSTALLATION
INSTRUCTIONS
Check that you have everything necessary for correct installation.
Proper installation is your responsibility.
Parts listed are available from your local Sears store or
Sears Service Center. For further information, please call
1-800-4-MY- HOM E®(1-800-46g-4663).
If You Have You Will Need to Buy
Laundry tub or Sump pump system (if not already
standpipe taller than available)
96 in. (2.4 m)
Tools needed:.
• 8 in. or 10 in. adjustable • Knife
wrench (for gas
connections) • Safety glasses
• Flat-blade screwdriver • Vent clamps
• Adjustable wrench that • Pipe-joint compound
opens to 1 in. (2.5 cm) or resistant to L.R gas
e/_6in. (14 mm) open-end • Caulking gun and
wrench (for adjusting compound (for installing
dryer feet) new exhaust vent)
• Level • Gloves
• _Ain. nut driver or socket • Pliers
wrench
• Wood block (for leveling) • Tin snips (new vent
Parts supplied:
Remove parts package from the washer basket. Check that all
parts were included.
• Ruler or measuring tape
installation)
o
3 4
1 in. (2.5 cm) 2 in. (5 cm) diameter to 1 in. (2.5 cm)
diameter standpipe diameter standpipe adapter, Part
Number 3363920
Overhead sewer Standard 20 gal. (76 L) 34 in. (86.4 cm)
tall drain tub or utility sink and sump
pump (available from local plumbing
suppliers)
Floor drain Siphon break, Part Number 285320,
additional drain hose, Part Number
285702 and connector kit,
Part Number 285442
Drain hose too short Drain hose, Part Number 285664 and
connector kit, Part Number 285442
Lint clogged drain Drain protector, Part Number 367031
Water faucets 2 longer water fill hoses:
beyond reach of fill 6 ft (1.8 m) Part Number 76314,
hoses 10 ft (3.0 m) Part Number 350008
@@;iii
5 6 7
1. Water inlet hoses (2)
2. Inlet hose flat washers (4)
3. Rear leveling legs (2)
4. Front leveling legs (2)
Parts needed:
Check local codes and with gas supplier, check existing gas
supply, electrical supply and venting, and read "Electrical
Requirements," "Gas Supply Requirements" and "Venting
Requirements" before purchasing parts.
Mobile home installations require special parts (listed following)
available for purchase from your local Sears store or Sears
Service Center. For further information, please call
1-800-4-MY-HOME ® (1-800-469-4663).
• Mobile Home Installation Kit. Ask for Part Number 346764.
• Metal exhaust system hardware.
5. Plastic strap
6. Drain hose
K Yellow, single wire hose clamp
8. Silver, double wire hose clamp
Explosion Hazard
Keep flammaMe materials and vapors, such as
gasoline, away from dryer.
FaiJure to do so can res@t in death, explosion,
or fire.
You will need
• A location that allows for proper exhaust installation. A gas
laundry center must be exhausted to the outdoors. See
"Venting Requirements."
• Agroundedelectricaloutletlocatedwithin2ft(61cm)of
eithersideofthelaundrycenter.See"Electrical
Requirements."
• Asturdyfloortosupportthelaundrycenterweight(laundry
center,waterandload)of500Ibs(226.8kg).
Alevelfloorwithamaximumslopeof1in.(2.5cm)under
entirelaundrycenter.Clothesmaynottumbleproperlyand
automaticsensorcyclesmaynotoperatecorrectlyifdryeris
notlevel.Installingoncarpetisnotrecommended.
• Awaterheatersettodeliver120°F(49°C)watertothe
washer.
• Hotandcoldwaterfaucetslocatedwithin4ft(1.2m)ofthe
hotandcoldwaterfillvalves,andwaterpressureof5-100psi
(34.5-689.6kPa).
Thelaundrycentermustnotbeinstalledorstoredinanarea
whereitwillbeexposedtowaterand/orweather.
Donotoperateyourwasherintemperaturesatorbelow32°F
(0°C).Somewatercanremaininthewasherandcancause
damageinlowtemperatures.See"Vacation,Storage,and
MovingCare"forwinterizinginformation.
Donotoperateyourdryerattemperaturesbelow45°F(7°C).At
lowertemperatures,thedryermightnotshutoffattheendofan
automaticcycle.Thiscanresultinlongerdryingtimes.
Checkcoderequirements.Somecodeslimit,ordonotpermit,
installationofthelaundrycenteringarages,closets,mobile
homes,orsleepingquarters.Contactyourlocalbuilding
inspector.
NOTE:Nootherfuel-burningappliancecanbeinstalledinthe
sameclosetasadryer.
Installation Clearances
The location must be large enough to fully open the dryer door.
Laundry Center Dimensions
Minimum installation spacing for recessed area or closet
installation
The following dimensions shown are for the minimum spacings
allowed.
• Additional spacing should be considered for ease of
installation and servicing.
• Additional clearances might be required for wall, door and
floor moldings.
• Additional spacing of 1 in. (2.5 cm) on all sides of the dryer is
recommended to reduce noise transfer.
For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
• Rear clearance may be 0 in. when house exhaust system is
lined up directly with dryer exhaust.
3" (7 6 cm)
(310 crn_)
o oa a o
24 m!
(155cm_)'
3" (7.6 cm)
--7
(0 cm) (60.64 cm) (0 era) (14 cm)
Mobile Home - Additional Installation Requirements
This laundry center is suitable for mobile home installations.
The installation must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280).
Mobile home installations require:
• Metal exhaust system hardware which is available for
purchase from your local Sears store or Sears Service Center.
• Mobile Home Installation Kit Part Number 346764. See "Tools
and Parts" section for ordering information.
Special provisions must be made in mobile homes to
introduce outside air into the dryer. The opening (such as a
nearby window) should be at least twice as large as the dryer
exhaust opening.
(Z5 crn) (69.22 cm)
!. Recessed area
2. Side view - closet or confined area
3. Closet door with vents
*Most installations require a minimum 51/2in. (14 cm) clearance
behind the dryer for the exhaust vent with elbow. See "Venting
Requirements."
Thelaundrycentercanbeinstalledusingthestandpipedrain
system(floororwall),thelaundrytubdrainsystem,orthefloor
drainsystem.Selectthedrainhoseinstallationmethodyouneed.
See"AlternateParts."
Standpipe drain system - wall or floor (view I & 2)
The standpipe drain requires a minimum diameter standpipe of
2 in. (5 cm). The minimum carry-away capacity can be no less
than 17 gal. (64 L) per minute. A 2 in. (5 cm) diameter to 1 in.
(2.5 cm) diameter standpipe adapter kit is available. See
"Alternate Parts."
The top of the standpipe must be at least 39 in. (99 cm) high and
no higher than 96 in. (2.4 m) from the bottom of the washer.
2
Laundry tub drain system (view 3}
The laundry tub needs a minimum 20 gal. (76 L)capacity. The top
of the laundry tub must be at least 34 in. (86.4 cm) above the floor
and no higher than 96 in. (2.4 m) from the bottom of the washer.
Floor drain system (view 4)
The floor drain system requires a siphon break that may be
purchased separately. See "Alternate Parts."
The siphon break must be a minimum of 28 in. (71 cm) from the
bottom of the washer. Additional hoses might be needed.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
A 120-volt, 60-Hz., AC-only, 15- or 20-ampere, fused
electrical supply is required. Time-delay fuse or circuit
breaker is recommended. It is also recommended that a
separate circuit serving only this appliance be provided.
To minimize possible shock hazard, the cord must be
plugged into a mating, 3 prong, ground-type outlet, grounded
in accordance with local codes and ordinances. If a mating i
outlet is not available, it is the personal responsibility and :
obligation of the customer to have the properly grounded
outlet installed by a qualified electrician
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
Do not ground to a gas pipe.
Check with a qualified electrician if you are not sure the
washer is properly grounded.
• Do not have a fuse in the neutral or ground circuit.
GROUNDING INSTRUCTIONS
[] For a grounded, cord-connected washer/dryer:
This washeddryer must be grounded. In the event of mal-
function or breakdown, grounding wilI reduce the risk of
electric shock by providing a path of least resistance for
electric current. This washer/dryer is equipped with a cord
having an equipment-grounding conductor and a grounding
plug. The plug must be plugged into an appropriate outlet
that is properly installed and grounded in accordance with
all local codes and ordinances.
WARNING: improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative or
personnel if you are in doubt as to whether the washer/dryer
is properly grounded. Do not modify the plug provided with
the washer/dryer: if itwill not fit the outlet, have a proper
outlet installed by a quaNfied electrician.
SAVE THESE INSTRUCTIONS
E×ptosion Hazard
Use a new AGA or CSA approved gas supply tine.
install a shut-off vaJve.
Securely tighten aH gas connections.
if connected to LP, have a qualified person make
sure gas pressure does not exceed 13" (33 cm)
water column.
E×ampJes of a qualified person inctude:
ticensed heating pereonneJ,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, e×plosion,
or fire.
Gas Type
Natural Gas:
This laundry center is equipped for use with NATURAL GAS. It is
design-certified by CSA International for L.R (propane or butane)
gases with appropriate conversion.
• Your laundry center must have the correct burner for the type
of gas in your home. Burner information is located on the
rating plate in the door well of your dryer. If this information
does not agree with the type of gas available, contact your
local Sears store or Sears Service Center.
LP. gas conversion:
Conversion must be made by a qualified technician.
No attempt shall be made to convert the appliance from the gas
specified on the model/serial rating plate for use with a different
gas without consulting the serving gas supplier.
Gas Supply Line
• 1/2in. IPS pipe is recommended
• 3/8in. approved tubing is acceptable for lengths under 20 ft
(6.1 m) if local codes and gas supplier permit.
• Lengths over 20 ft (6.1 m) should use larger tubing.
• Must include 1/8in. NPT plugged tapping accessible for test
gauge connection, immediately upstream of the gas supply
connection to the dryer (see illustration).
• Gas supply line coupling must be 34 in. (86.4 cm) to 37 in.
(94 cm) from the floor.
Must include a shutoff valve:
An individual shutoff valve must be installed within six (6) feet
(1.8 m) of the laundry center in accordance with the National
Fuel Gas Code, ANSI Z223.1. The location should be easy to
reach for opening and closing.
......... 1
............................2
..................................3
1. Gas shutoff valve
2. V8in. NPT plugged tapping
3. Y; in. NPT gas supply line
4. Gas supply line coupling 34 in. (86.4 cm) min.
to 37in. (94 cm) max. from floor
If you are using natural gas, do not use copper tubing.
If your laundry center has been converted to use L.R gas,
% in. L.R compatible copper tubing can be used. If the total
length of the supply line is more than 20 ft (6.1 m), use larger
tubing.
NOTE: Pipe joint compounds that resist the action of L.R gas
must be used. Do not use TEFLON °t tape.
Dryer Gas Connection
• This laundry center is equipped with its own permanent,
flexible gas connector, design-certified by CSA International,
for connecting the laundry center to the gas supply line.
\
Flexible gas connector
Burner Input Requirements:
Elevations up to 10,000 feet (3,048 meters):
• The design of this laundry center is certified by CSA
International for use at altitudes up to 10,000 ft (3,048 m)
above sea level at the B.T.U. rating indicated on the model/
serial number plate. Burner input adjustments are not
required when the dryer is operated up to this elevation.
Elevations above 10,000 feet (3,048 meters):
• When installed above 10,000 ft (3,048 m) a 4% reduction of
the burner B.T.U. rating shown on the model/serial number
plate is required for each 1,000 ft (305 m) increase in
elevation.
Gas Supply Pressure Testing
• The laundry center must be disconnected from the gas
supply piping system during any pressure testing.
1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company
Exhaust hood must be at least 12 in. (30.5 cm) from the ground or
any object that may be in the path of the exhaust (such as
flowers, rocks or bushes, etc.).
If using an existing vent system, clean lint from the entire length
of the system and make sure exhaust hood is not plugged with
lint. Replace any plastic or metal foil vent with rigid metal or
flexible metal vent.
'sts .... Legs
Fire Hazard
Use a heavy metaJ vent.
Do not use a pJaetic vent.
Do not use a metaJ foil vent.
Failure to follow these instructions can result in
death or fire.
WARNING: To reduce the risk of fire, this laundry center
MUST BE EXHAUSTED OUTDOORS.
4 in. (10.2 cm) heavy metal exhaust vent and clamps must be
used. DURASAFE TM venting products are recommended and are
available from your local Sears store or Sears Service Center.
DURASAFE TMvent products can be purchased from your dealer.
For further information, please call 1-800-4-MY-HOME ®
(1-800-469-4663} or visit our Internet site at www.sears.com
• The dryer exhaust must not be connected into any gas vent,
chimney, wall, ceiling, or a concealed space of a building.
• Do not use an exhaust hood with a magnetic latch.
• Do not install flexible metal vent in enclosed walls, ceilings or
floors.
Use clamps to seal all joints. Exhaust vent must not be
connected or secured with screws or other fastening devices
which extend into the interior of the duct. Do not use duct
tape.
IMPORTANT: Observe all governing codes and ordinances.
Excessive Weight Hazard
Use two or more people to move and install
washer/dryer.
Failure to do so can result in back or other injury.
To protect the floor, use a large flat piece of cardboard from the
shipping carton. Gently place the laundry center on its side, on
the cardboard.
Install the rear leveling legs
1. Push legs into holes in rear corners until they snap into place.
@@;iii
2. Check adjustability of rear legs by pushing in one leg. The
other leg should come out. Check both legs. If they do not
move freely, repeat step 1.
Install the front leveling legs
1. Examine the front leveling legs. Find the diamond marking.
2. Screw front legs by hand, into the holes in the triangular
braces in the front corners. Use wrench to finish turning the
legs until the diamond marking is no longer visible.
Improper venting can cause moisture and mintto collect
indoors, which may reeumt in:
[] Moisture damage to woodwork, furniture, paint, waN-
paper, carpets, etc.
[] Housecleaning problems and health problems.
Use a heavy metal vent. Do not use plastic or metal foil vent.
Rigid metal vent is recommended to prevent crushing and
kinking.
Flexible metal vent must be fully extended and supported when
the laundry center is in its final position. Remove excess flexible
metal vent to avoid sagging and kinking that may result in
reduced airflow.
An exhaust hood should cap the vent to prevent rodents and
insects from entering the home.
3. Carefully stand the laundry center upright.
For mobile home use
Laundry centers with gas dryers must be securely fastened to the
floor.
Mobile home installations require a Mobile Home Installation Kit.
See "Tools and Parts" section for ordering information.
Remove sck 9
1. Open the washer lid. The latch under the dryer will keep the
lid open.
2. Pull the foam packing ring out of the washer.
NOTE: Keep the foam ring and use it when transporting your
laundry center. This packing material is used to keep the washer
tub stable during transport.
Proper connection of the drain hose protects your floors from
damage due to water leakage. To prevent the drain hose from
coming off or leaking, it must be installed per the following
instructions:
IMPORTANT: To ensure proper installation, this procedure must
be followed exactly.
1. Check the drain hose to see whether it is the proper length.
2. Wet the inside of the straight end of the drain hose with tap
water. DO NOT USE ANY OTHER LUBRICANT.
3. Squeeze ears of the silver, double-wire clamp with pliers to
open. Place clamp over the straight end of the drain hose
_Ain. (6.4 mm) from the end.
For laundry tub or standpipe drain systems
1. Open the yellow, single-wire clamp and slide over the hooked
end of the drain hose to secure the rubber and corrugated
sections together.
1. Hooked end
2. Drain hose
2. Put the hooked end of drain hose into laundry tub or
standpipe. Rotate hook to eliminate kinks.
To prevent drain water from going back into the washer:
• Do not straighten hooked end of the drain hose and force
excess drain hose into standpipe. Hose should be secure but
loose enough to provide a gap for air.
• Do not lay excess hose on the bottom of the laundry tub.
For use with floor drain
Remove the drain hose hook from the corrugated drain hose. You
may need additional parts. See "Floor Drain" under "Alternate
Parts."
1. Insert a new flat washer (supplied) into each end of the inlet
hoses. Firmly seat the washers in the couplings.
4. Open clamp. Twist hose back and forth while pushing onto
drain connector on the side of the laundry center. Continue
until hose contacts the ribbed stops on the cabinet.
\
\
\
\
\
5. Place clamp over the area marked "CLAMR" Release clamp,
1 2
1. Coupling
2. Washer
Connect the inlet hoses to the water faucets
Make sure the washer basket is empty.
2. Attach the hose with the red coupling to the hot water faucet.
Screw on coupling by hand until seated on the washer.
3. Attach the hose with the blue coupling to the cold water
faucet. Screw on coupling by hand until seated on the
washer.
4. Using pliers, tighten the couplings with an additional two-
thirds turn.
J
d
NOTE: Do not overtighten. Damage to the valves can result.
10
Clear the water lines
5. Run water through both faucets and inlet hoses, into a bucket
or laundry tub, to get rid of particles in the water lines that
might clog the inlet valve screens.
Connect the inlet hoses to the washer
6. Attach the hose with the blue coupling to the cold (top) inlet
valve. Screw on coupling by hand until seated on the washer.
Using pliers, tighten the couplings with an additional two-
thirds turn.
NOTE: Do not overtighten. Damage to the valves can result.
1. Cold water inlet valve (blue)
2. Hot water inlet valve (red)
7. Attach the hose with the red coupling to the hot water
(bottom) inlet valve. Screw on coupling by hand until seated
on the washer. Using pliers, tighten the couplings with an
additional two-thirds turn.
NOTE: Do not overtighten. Damage to the valves can result.
If you are working in a closet or recessed area
Move the laundry center into its final position and remove
cardboard from under laundry center. Remove the access panel
by removing 3 Phillips-head screws and one bumper, located at
the top of the access panel. Set panel, screws, and bumper
aside. Complete hookup of water hoses and (on gas models) the
flexible gas connector through the access area.
1. Move the laundry center to its final location and remove any
cardboard used to move the laundry center.
2. Locate the plastic strap included in the parts package.
Beaded tie strap
3. Wrap the drain hose to the laundry tub leg or standpipe with
the plastic strap (1 or 2 below) and secure.
If the water faucets and the drain standpipe are recessed, put
the hooked end of the drain hose in the standpipe. Tightly
wrap the plastic strap around the water inlet hoses and the
drain hose (3 above).
::iiiii
Typical exhaust installations
Typical installations vent the dryer from rear of the laundry center.
Other installations are possible.
4
1 ......................!
Check for leaks
8. Turn on the water faucets and check for leaks. A small
amount of water might enter the washer. You will drain this
later.
NOTE: Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Record hose installation or replacement dates for
future reference.
• If you connect only one water hose, you must cap off the
remaining water inlet port.
• Periodically inspect and replace hoses if bulges, kinks, cuts,
wear, or leaks are found.
ix;;i !;x;xI
3 ........
1. Dryer 5. Elbow
2. Rigid metal or 6. Clamps
flexible metal vent 7. Elbow
3. Clamps 8. Exhaust hood
4. Wall
Optional exhaust installations
This laundry center can be converted to exhaust out the right or
left side. To convert the laundry center, use Side Exhaust Kit
Part Number 279823. If your laundry center was previously
exhausted from the right or left side, it can be converted to rear
exhaust by using standard offset connections. To cover the hole
in the side, one of the following plugs can be added:
692790 (white)
3979370 (graphite)
3977784 (biscuit)
11
Follow the instructions in the kit to install. Kits are available from
your local Sears store or Sears Service Center.
1. Standard rear offset exhaust installation
2. Rear exhaust for offset close clearance connection
3. Left or right side exhaust installation
Alternate installations for close clearances
Venting systems come in many varieties. Select the type best for
your installation. Three close-clearance installations are shown.
Refer to the manufacturer's instructions provided with the vent
system.
Special provisions for mobile home installations
The exhaust vent must be securely fastened to a noncombustible
portion of the mobile home structure and must not terminate
beneath the mobile home. Terminate the exhaust vent outside.
Determine Vent Length
1. Select the route that will provide the straightest and most
direct path outdoors. Plan the installation to use the fewest
number of elbows and turns. When using elbows or making
turns, allow as much room as possible. Bend vent gradually
to avoid kinking. Avoid 90° turns.
._-'r ........
(
k I
"\ ( ......
1 2
1.Loop system with standard elbows
2. Loop system with one offset & one standard elbow
3. Vent system with one periscope (2 in. [5 cm] clearance)
NOTE: The following kits for close clearance alternate
installations are available for purchase. For further information,
please call 1-800-4-MY-HOME ®(1-800-469-4663).
• Over the top Installation:
Part Number 26-49900
• Periscope Installation (For use with dryer vent to wall vent
mismatch):
Part Number 26-49901 - Less than 5 in. (12.7 cm) mismatch
Part Number 26-49908 - 5 in. (12.7 cm)to 18 in. (45.7 cm)
mismatch
Part Number 26-49904 - 18 in. (45.7 cm) to 29 in. (73.7 cm)
mismatch
Part Number 26-49905 - 29 in. (73.7 cm) to 50 in. (127 cm)
mismatch
bett__
2. Determine vent length.
The maximum length of the exhaust system depends upon:
• The type of vent (rigid metal or flexible metal).
• The number of elbows used.
• Type of hood.
Recommended hood styles are shown here.
2
(10.2 cm)
1.Louvered hood style
2. Box hood style
The angled hood style (shown following) is acceptable.
See the exhaust vent length chart that matches your hood
type for the maximum vent lengths you can use.
Exhaust systems longer than specified will:
• Shorten the life of the dryer.
• Reduce performance, resulting in longer drying times and
increased energy usage.
12
3. Determine the number of elbows you will need.
IMPORTANT: Do not use vent runs longer than those
specified in the Vent Length Chart.
The following Vent Length Chart helps you determine your
maximum vent length based on the number of 90° turns or
elbows you will need and the type of vent (rigid metal or
flexible metal) and hood that you will use.
Vent Length Chart
Number Type of Vent Box or Angled
of Louvered hoods
90° turns hoods
or elbows
0 Rigid metal 34 ft (12.2 m) 29 ft (10.7 m)
Flexible metal 21 ft (7.6 m) 16 ft (6.1 m)
1 Rigid metal 24 ft (9.7 m) 20 ft (8.2 m)
Flexible metal 15 ft (6.4 m) 10 ft (4.9 m)
if_ttli@ _,,_4:;;;_,OOIll leoIloIl
1.
Remove the red cap from the flexible gas connector.
2.
Remove the 1/2in. NPT adapter from the flexible gas
connector (it will be necessary to use two adjustable
wrenches).
Install the adapter on the 1/2in. rigid gas supply pipe using
pipe-joint compound.
2 Rigid metal 14 ft (7.3 m) 12 ft (5.8 m)
Flexible metal 7 ft (4.6 m) 2 ft (3.0 m)
NOTE: Side exhaust adds a 90° turn inside the laundry center. To
determine maximum exhaust length, add one 90° turn to the
chart.
1. (Optional) Put on safety glasses and gloves.
2. Install exhaust hood. Use caulking compound to seal exterior
wall opening around exhaust hood.
3. Connect vent to exhaust hood. Vent must fit inside exhaust
hood. Secure vent to exhaust hood with 4 in. (10.2 cm)
clamp.
4. Run vent to dryer location. Use the straightest path possible.
See "Determine Vent Length." Avoid 90° turns. Use clamps to
seal all joints. Do not use duct tape, screws or other fastening
devices that extend into the interior of the vent to secure
vent.
Properly leveling your laundry center prevents excessive noise
and vibration.
1. Check the levelness of the laundry center by placing a level
on the top edge of the washer, first side to side, then front to
back.
1. _2in. rigid gas supply pipe
2. Use pipe-joint compound
3. _2in. NPTadapter
4. Do not use pipe-joint compound
5. Flexible gas connector
NOTE: For L.R gas connections, you must use pipe joint
compound resistant to the action of L.R gas. Do not use
TEFLON _ tape.
Attach the flexible gas connector to the 1/=in. NPT adapter.
Do not use pipe-joint compound for this connection.
There should bea natural loop in the flexible gas connector.
The flexible gas connector must not be twisted, kinked or
attached with any sharp bends.
I /;.', "°oooo.o,
5. All connections must be wrench tightened.
6. Open the shutoff valve in the supply. The valve is open when
the handle is parallel to the gas pipe.
If the laundry center is not level, prop up the front with a
wood block and adjust the feet up or down as necessary.
Remove wood block and lower laundry center. Repeat this
step until the laundry center is level.
1. Closed valve
2. Open valve
Test all connections by brushing on an approved
noncorrosive leak-detection solution. Bubbles will show a
leak. Correct any leak found.
13
1. Using a 4 in. (10.2 cm) clamp, connect vent to exhaust outlet
in laundry center. If connecting to existing vent, make sure
the vent is clean. The vent must fit over the exhaust outlet
and inside the exhaust hood. Make sure the vent is secured
to exhaust hood with a 4 in. (10.2 cm) clamp.
2. Move laundry center into final position. Do not crush or kink
vent. Make sure laundry center is level.
3. (On gas models) Check to be sure there are no kinks in the
flexible gas line.
1. Check to be sure all parts are now installed. If there is an
extra part, go back through the steps to see which step was
skipped.
2. Check to be sure you have all of your tools.
3. Dispose/recycle all packaging materials. Keep the plastic
foam for use if the laundry center should be transported.
4. Check the laundry center's final location. Be sure the vent is
not crushed or kinked.
5. Check to be sure the laundry center is level and front leveling
feet are tight. See "Level Laundry Center."
6. Plug into a grounded 3 prong outlet. Turn power on.
7. Check to be sure the water faucets are on.
8. Check for leaks around faucets and inlet hoses.
9. Remove the blue protective film on the console and any tape
remaining on the laundry center.
10. Read "Washer Use" and "Dryer Use."
11. Wipe the dryer drum interior thoroughly with a damp cloth to
remove any dust.
12. To test the washer, measure 1/2the normal recommended
amount of detergent and pour it into the washer. Close the lid.
Select HEAVY DUTY and pull out the Cycle Control knob.
Allow the washer to complete one whole cycle.
13. To test the dryer, set the dryer on a full heat cycle (not an air
cycle) for 20 minutes and start the dryer.
If the dryer will not start, check the following:
• Laundry Center is plugged into a grounded 3 prong
outlet.
• Start button has been firmly pushed.
• Electrical supply is connected.
• House fuse is intact and tight, or circuit breaker has not
tripped.
• Dryer door is closed.
14. When the dryer has been running for 5 minutes, open the
dryer door and feel for heat. If you do not feel heat, turn the
dryer off and check to see whether the gas supply line shutoff
valve is open.
• If the gas supply line shutoff valve is closed, open it, then
repeat the 5-minute test as outlined above.
• If the gas supply line shutoff valve is open, contact a
qualified technician.
FEATURES AND
BENEFITS
The DUAL-ACTION TM PlusAgitatorisa uniquelydesigned
agitator that helps push clothes that are on top down to the
bottom of the washer where the best cleaning action takes place.
..... .....
Durable finish resists scratching, staining and odors for long-
lasting quality. Fabrics are protected by the smooth wash basket.
This laundry center features 4 different ways to vent your dryer. A
properly exhausted laundry center will give you the shortest
drying time, lower your utility bill and extend the life of the laundry
center.
14
WASHER USE
HEAVY DUTY WATERTEMP WATER LEVEL
SPIN REGULAR
RINSE PERMANENT MEQ,USI
PRESS c0L0 WARM SMALL lARgE
SHORT 8
REGUL_[_10 I
SUPEN 12 ....
KNiT/DEL|CATE
SOAK'
Fire Hazard
Never place items in the washer that are
dampened with gasoline or other flammable
fluids.
No washer can completely remove oH.
Do not dry anything that has ever had any type of
oit on it (including cooking oits).
Doing so can resutt in death, explosion, or fire.
WARM WARM LeAD
CSLB HOT ® e
@ LOA8 LOAB
Turn the WATER LEVEL selector knob to the correct setting
for your wash load and the type of fabric being washed.
• Choose a load size that allows the load to move freely for
best fabric care. See "Loading." i
• You may change the load size selection after the washer
has started filling by turning the selector to a different
setting
Set the WATER TEMP selector to the correct setting for the
type of fabric and soils being washed.
RESET
WATER LEVEL
WATER TEMP
WARM WARM
CQLB WARN
MEBHUM
LgA#
® e
WARNING: To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
The following is a guide to starting your washer. Periodic
references to other sections of this manual provide more detailed
information.
1. Pour measured powdered or liquid detergent into the washer.
If desired, add powdered or liquid color safe bleach.
2. Place a load of sorted clothes in the washer.
• Load evenly to maintain washer balance. Mix large and
small items. See "Loading."
• Items should move easily through the wash water.
Overloading can cause poor cleaning.
3. Close the washer lid.
Use the warmest water safe for the fabric. Follow garment
label instructions.
Water Temp Use For
Hot Whites and pastels
Heavy soils
Warm Bright colors
Moderate to light soils
Cold Colors that bleed or fade
Light soils
NOTE: In wash water temperatures colder than 70°F
(21°C), detergents de not dissolve well. Soils can be difficult
to remove. Some fabrics can retain wear wrinkles and have
increased pilling (the formation of small lint-like bails on the
surface of garments).
15
6.
Push in the Cycle Control knob and turn it clockwise to the
wash cycle you want. Pull out the Cycle Control knob to start
the washer.
To stop or restart your washer:
• To stop the washer at any time, push in the Cycle Control
knob.
• To restart the washer, close the lid (if open) and pull out
the Cycle Control knob.
This section describes the available wash cycles and will help
you make the best cycle selections for your wash loads. Each
cycle is designed for different types of fabric and soil levels.
• The washer pauses briefly throughout each cycle. These
pauses are normal. Refer to "Normal Sounds" for sounds you
may hear during a wash cycle.
• Refer to "Understanding Washer Cycles" to learn what
happens during a wash cycle.
RINSE
SPIN
KN|T/DEL|CATE
SOAK
_INSE
Soak
The Soak cycle features 4 minutes of agitation followed by an
unlimited soak time to help remove heavy soils and stains that
need pretreatment. You will need to reset the washer to a SPIN
setting to remove water.
• The Soak cycle should be followed by the Heaw Duty or
Permanent Press or Prewash cycle with additional detergent.
NOTE: Hot water is not recommended for soaking. It may set
some stains.
Prewash
Use this cycle to get up to 4 minutes of agitation to help remove
heavy soils and stains that need pretreatment.
• The Prewash cycle should be followed by the Heavy Duty or
Permanent Press cycle with additional detergent.
When using extra detergent for heavily soiled clothes, or washing
special-care items, you may find an extra rinse and spin is
needed.
1. Push in the Cycle Control knob and turn it clockwise to any of
the RINSE settings.
• For fast agitation and spin, use the Heavy Duty cycle.
• For slow agitation and spin, use the Permanent Press
cycle.
2. Set the WATER LEVEL and WATER TEMP controls to the
desired setting.
3. Pull out the Cycle Control knob. The washer fills to the
selected load size, agitates, drains, and spins.
Heavy Duty
Use this cycle for sturdy or heavily soiled loads. Wash combines
fast speed agitation and fast spin speeds.
• Use the Super or Regular settings for heavily soiled and
sturdy fabrics.
• Use the Short setting for light soil and delicate fabrics.
Permanent Press
The Permanent Press Cycle includes a load cooling process that
reduces wrinkling. Wash combines fast and slow speed agitation
and slow spin speeds.
When the timer reaches Pause, the washer will drain and pause
for approximately 2 minutes while some of the wash water is
drained and replaced with rinse water.
Knit/Delicate
Use this cycle for lingerie and loosely knit items. Partway through
the cycle the washer pauses and soaks the load for more gentle
care of lightly soiled delicate items. Wash combines slow speed
agitation for gentle soil removal and slow spin speeds to reduce
wrinkling.
A drain and spin may help shorten drying times for some heavy
fabrics or special-care items by removing excess water.
1. Push in the Cycle Control knob and turn it clockwise to any of
the SPIN settings.
• For a fast spin, use the Heavy Duty cycle.
• For a slow spin, use the Permanent Press cycle.
2. Pull out the Cycle Control knob. The washer drains, then
spins.
When the Cycle Control knob is set to a number and pulled out,
the washer fills (to the selected load size) before agitation and
timing start. The washer begins agitating immediately after filling;
agitation occurs with the washer lid up or down.
During agitation, the agitator creates a continuous rollover action
that provides a thorough cleaning of the wash load.
After agitation starts, the Cycle Control knob turns clockwise until
it points to an Off area and the cycle ends.
16
Loading...