Kenmore 11022442100, 11022432100, 11022422100 Owner’s Manual

Owner's Manual and Installation Instructions

One-Speed

AUTOMATIC WASHERS

IMPORTANT:

Read and follow all safety and operating instructions before first use of this product.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. Sears Canada Inc., Toronto, Ontario, Canada MSB 2B8

8526114 PRINTED IN U.S.A. 2/01

www.sears.com

www,sears,ca

BEFORE USING YOUR NEW WASHER 2

KENMORE AUTOMATIC WASHER WARRANTY 3

WASHER SAFETY ............ 4

INSTALLATION REQUIREMENTS 6

INSTALLATION INSTRUCTIONS 10

OPERATING YOUR WASHER ..... 14

LAUNDRY TIPS ........... 20

CARING FOR YOUR WASHER _ _ _ 22

TROUBLESHOOTING ........ 23

SEARS MAINTENANCE AGREEMENT 27

Please read this manual. It will help you install and operate your new

Kenmore washer in the most economical way. For more information about the care and operation of Kenmore appliances,

call your nearest Sears store, You will need the complete model and serial numbers when requesting information.

Your washer's model and serial numbers are located on the Model and Serial

Number Plate.

"tj

ModelandSerial NumberPlato

Use the space below to record the model number and serial number of your new

Kenmore washer.

Model No.

Serial No.

Date of Purchase

Keep this book and your Sears Salescheck (receipt) in a safe place for

futu re reference.

Limited Lifetime Warranty on

White Porcelain Basket

For the lifetime of the washer from the

date of purchase, Sears will replace the white porcelain wash basket if it chips

or rusts due to defective material or workmanship. After the first year, you

will be charged for labor.

Limited 10-Year Warranty on Plastic Tub*

For the second through tenth year from the date of purchase, Sears will replace the plastic tub if it is defective in material or workmanship. After the first

year, you will be charged for labor.

Limited 5-Year Warranty on Gearcase Parts*

For the second through fifth year from the date of purchase, Sears will replace

any gearcase parts that are defective in material or workmanship. After the first

year, you will be charged for labor.

Full 1-Year Warranty on "Spreckle" Porcelain Basket

For one year from the date of

purchase, when this washer is installed and operated according to the instruc- tions that come with it, Sears will replace the "spreckle" (speckled sur- face) porcelain wash basket if it chips

or rusts due to defective material or workmanship.

Full 1-Year Warranty on Mechanical and Electrical parts

For one year from the date of pur_ chase, if this washer is installed and operated according to the instructions that come with it, Sears will repair or replace any of its mechanical or electrical parts if they are defective in material or workmanship.

Warranty Restriction

Ifthis washer is operated for any pur- pose other than private family use, all warranty coverage is restricted to 90 days from the date of purchase.

Warranty Service Warranty service is available by

contacting your nearest Sears Service Center in the United States or Canada.

This warranty applies only while this washer is used in the United States or

Canada.

This warranty gives you specific legal rights and you may also have other rights that vary from state to state or province to province.

Sears, Roebuck and Co., Dept. 817WA,

Hoffman Estates, IL 60179 Sears Canada Inc.,

Toronto, Ontario, Canada M5B 2B8

*In Canada, a different warranty may apply.

In the U.S. for Sears warranty information or to contact a Sears Service Center', call

1-80O4-MY-HQME _ (I-890-469-4663).

In Canada, calI 1-877-533-6937.

Your safety and the safety of others are very important.

We have provided many importantsafety messages in this manual and on your appliance. Always readand obey all safetymessages,

This isthe safety alert symbol,This symbolalertsyou to potentialhazards that can killor hurtyou and others.

Allsafety messages willfollowthe safety alert symbol and eitherthe word"DANGER" or "WARNING."

These words mean:

You can be Idlled or seriously

Injured If you don't Immediately

follow Instructions. You can be Idlled or seriously

Injured If you don't follow instructions.

Allsafety messages willtell you what the potentialhazard is,tell you how to reducethe chance of injury,and tellyou what can happen ifthe

instructionsare not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons

when using your washer, follow basic precautions, including the following:

• Read all instructions before using the washer.

• Do not wash articles that have been previously cleaned in, washed in,

soaked in, or spotted with gasoline, dry-cleaning solvents, other

flammable or explosive substances as they give off vapors that could

ignite or explode.

• Do not add gasoline, dry_cleaning solvents, or other flammable or

explosive substances to the wash water. These substances give off

vapors that could ignite or explode.

• Under certain conditions, hydrogen gas may be produced in a hot water

system that has not been used for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been used for such a period,

before using a washing machine, turn on ell hot water faucets and let the

water flow from each for several minutes. This will release any

accumulated hydrogen gas,As the gas is flammable, do not smoke or

use an open flame during this time.

SAVE THESE INSTRUCTIONS

• Do not allow children to play on or in the washer. Close supervision of chil- dren is necessary when the washer is

used near children.

• Before the washer is removed from service or discarded, remove the door

or lid,

• Do not reach into the washer if the drum, tub or agitator is moving.

• Do not install or store this washer where it will beexposed to the weather.

• Do not tamper with controls.

• Do not repair or replace any part of the washer or attempt any servicing unless

specifically recommended in the Owner's Manual or in published user-

repair instructions that you understand and have the skills to carry out.

• See the "Installation Requirements" section for grounding requirements.

Tools and Parts

Assemble the necessary tools and supplies before beginning the washer

installation. The parts supplied are in the

washer basket.

Tools needed for connecting the drain

hose and water inlet hoses:

• Pliers that open to 1_ in. (3.95 cm)

• Flashlight (optional)

Parts supplied:

oo oo

4 5

1. Drain hose

2 Silve_ double-wire hose clamp

(for the bottom of the drain hose)

3. Yellow, single-wire hose clamp (for the top of the drain hose)

4. Water inlet hoses (2)

5. Flat water inlet hose washers (4)

Tools needed for securing the drain

hose and leveling the washer:

• Open end wrench _ in. (1.43 cm)

• Level

• Wood block

• Ruler or measuring tape Parts supplied:

1 2

1. Shipping strap with fastener

2 Front leveling feet with nuts (2)

Alternate Parts You May Need

Parts listed are available from your local Sears store or Sears Service Center.

Please reference the service numbers located on the back page of this manual.

If you have: You will need to buy: Laundry tub or Sump pump system (if

standpipe not already available) taller than 96

in. (2.4 m)

1 in. (2.5 cm) 2 in. (5 cm) diameter to diameter 1 in. (2.5 cm) diameter standpipe standpipe adapter, Part

No. 3363920

Overhead Standard 20 gal (76 L) sewer 39 in. (99 cm) tall drain

tub or utility sink, sump

pump and connectors (available from local plumbing suppliers)

Floor drain Siphon break, Part

Number 285320; addi-

tional drain hose, Part

Number 3357090 and

connector kit, Part

Number 285442

Water faucets 2 longer water fill hoses: beyond reach 6 ft (1.8 m) Part Number of fill hoses 76314, 10 ft (3.0 m) Part

Number 350008

Drain hose too Drain hose, Part No. short 388423 and hose kit,

Part No. 285442

Drain hose Hose kit, Part No. that is too long 285442

Lint clogged Drain protector, Part No. drain 367031

Location Requirements

Selecting the proper location for your washer improves performance and mini- mizes noise and possible washer "walk."

Your washer can be installed in a base- ment, laundry room, closet, or recessed

area. (See "Drain System.") Proper installation is your responsibility.

You will need:

• A water heater set to deliver 120°F (49°C) water to the washer.

• A grounded electrical outlet located with- in 4 ft (1.2 m) of where the power cord is attached to the back of the washer.

(See "Electrical Requirements.")

• Hot and cold water faucets located with* in 4 ft (1.2 m) of the hot and cold water

fill valves, and water pressure of 5-100 psi (34.5_689.6 kPa). Washers with

triple dispensers require 20-100 psi (138.0-689.6 kPa) for best performance.

• A level floor with a maximum slope of

1 in. (2.5 cm) under entire washer.

Installing the washer on carpeting is not recommended.

• A sturdy floor to support the washer weight (washer, water and load) of 315 Ibs (143 kgs).

Do not store or operate your washer in temperatures at or below 32°F (0°C).

Some water can remain in the washer and can cause damage in low temperatures.

See "Washer Care" for winterizing infor- mation.

Recessed area or closet installation The dimensions shown are for the rec- ommended spacing allowed, except the

closet door ventilation openings. The dimensions shown for the closet door

ventilation openings are the minimum required.

m m

•o"_.f_ _" ,_, '_"4=4"I_,_" _-I4"I_

1 2

41,,=

24 ,,2

1. Front view

2. Side view

& Closet doer with vents

• Additional spacing should be consid-

ered for ease of installation and ser- vicing.

• Additional clearances may be required

for wall, door and floor moldings.

• Additional spacing of 1 in. (2.5 cm) on

all sides of the washer is recommend- ed to reduce noise transfer.

• If a closet door is installed, the mini-

mum air openings in the top and bot-

tom of the door are required. Louvered

doors with air openings in the top and bottom are acceptable.

• Companion appliance spacing should

also be considered.

Drain System

The washer can be installed using the standpipe drain system (floor or wall), the

laundry tub drain system, or the floor

drain system. Select the drain hose instal-

lation method you need. (See "Alternate Parts You May Need.")

I 2

Standpipe drain system - wall or floor (view 1 & 2)

The standpipe drain requires a minimum diameter standpipe of 2 in. (5 cm). The minimum carry-away capacity can be no

less than 17 gal (64 L) per minute. A2 in.

(5 cm) diameter to 1 in. (2.5 cm) diameter standpipe adapter kit is available. (See

"Alternate Parts You May Need.") The top of the standpipe must be at least

39 in. (99 cm) high and no higher than 96

in. (2.4 m) from the bottom of the washer.

Floor drain system (view 2)

The floor drain system requires a siphon break that may be purchased separately. (See "Alternate Parts You May Need.")

The siphon break must be a minimum of 28 in. (71 cm) from the bottom of the washer. Additional hoses might be

needed.

Electrical Requirements

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these

instructions can result in death, fire, or electrical shock.

Laundry tub drain system (view 1)

The laundry tub needs a minimum 20 gal (76 L) capacity. The top of the laundry tub

must be at least 39 in. (99 cm) above the floor and no higher than 96 in. (2.4 m)

from the bottom of the washen

• A 120-volt, 60-Hz. AC-only, 15- or 20- ampere, fused electrical supply is required. Time-delay fuse or circuit

breaker is recommended. It is recom- mended that a separate circuit serving

only this appliance be provided.

• This washer is equipped with a power supply cord having a 3 prong ground plug.

• To minimize possible shock hazard, the cord must be plugged into a mating, 3 prong, ground-type outlet, grounded in

accordance with local cedes and ordi- nances. If a mating outlet is not avail-

able, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualified electrician.

• If codes permit and a separate ground wire is used, it is recommended that a

qualified electrician determine that the ground path is adequate.

• Do not ground to a gas pipe.

• Check with a qualified electrician if you are not sure the washer is properly grounded.

• Do not have a fuse in the neutral or ground circuit.

1. 3 prong grounding plug

2. 3 prong grounding-type outlet

3. Ground prong 4 Power supply cord

GROUNDING

INSTRUCTIONS

For a grounded, cord-connected

washer:

This washer must be grounded. In the event of a malfunction or breakdown,

grounding will reduce the risk of electrical shock by providing a path of

least resistance for electric current. This

washer is equipped with a cord having

an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that

is properly installed and grounded in accordance with all local codes and

ordinances.

WARNING: Improper connection of

the equipment-grounding conductor can

result in a risk of electric shock. Check

with a qualified electrician or service-

man ifyou are in doubt as to whether

the appliance is properly grounded. Do not modify the plug provided with

the appliance - if it will not fit the outlet have a proper outlet installed by a

qualified electrician. For a permanently connected

washer:

This washer must be connected to a grounded metal, permanent wiring

system, or an equipment grounding conductor must be run with the circuit

conductors and connected to the equipment-grounding terminal or lead

on the appliance.

Before You Start

• To prevent floor damage, set the washer onto cardboard before moving

across floor.

• Move the washer to within approximate-

ly 3 feet (90 cm) of the final location.

Remove Shipping Strap

Removing the shipping strap is necessary

for smooth operation. If the shipping strap

is not removed, the washer will make excessive noise.

1. Do not cut yellow strap. Pull yellow

strap firmly, until completely removed from washer. Depending on your model, there will be either two or three cotter pins on the end of the shipping strap when it is pulled out of the washer. The electrical plug is attached to this shipping strap.

o o

3, Cut the shipping strap about 16 in,

(40 cm) from plug end, Look for the words "CUT HERE." Discard end with

the cotter pins, Slide remainder of shipping strap from the power

cord. You will use the remainder of the shipping strap later to secure the

drain hose.

Connect Drain Hose

Proper connection of the drain hose will

protect your floors from damage due to water leakage, To prevent the drain hose from coming off or leaking, it must be

installed per the following instructions.

IMPORTANT: To ensure proper installa- tion, this procedure must be followed exactly.

1, Check the drain hose to see if it is

the proper length.

Wet the inside of the straight end of the drain hose with tap water. DO

NOT USE ANY OTHER LUBRI-

CANT.

Squeeze ears of silver, double-wire clamp with pliers to open, Place clamp over the straight end of the

drain hose ¼ in. (6 ram) from the end.

2. Pull firmly to remove the end of the shipping strap that remains pinned to

the back of the washer, This will release the rear self-leveling feet.

_1/4"

(6 mm)

4. Open clamp. Twist hose back and forth while pushing down onto drain

connector at the bottom of the wash- er. Continue until hose contacts the

ribbed stop on the cabinet.

5. Place clamp over area marked "CLAMR" Release clamp.

1/4"

rnm)

1.Drain Hose

2. Clamp

3. Ribbed Stop

4. Cabinet

For standpipe or laundry tub drain

systems:

1. Open yellow, single-wire clamp with pliers and slide over hooked end of

drain hose to secure the rubber and corrugated sections together.

• For floor drain installation, see kit num- ber required under "Alternate Parts You May Need."

Connect the Inlet Hoses

Insert new flat washers (supplied)into each end of the inlet hoses. Firmly

seat the washers in the couplings.

1 2

1. Coupling

2. Washer

Connect the inlet hoses to the water faucets

Make sure the washer basket is empty.

Attach the hose with the red coupling to the hot water faucet. Screw on cou-

pling by hand until seated on the washer,

Attach the hose with the blue coupling to the cold water faucet. Screw on

coupling by hand until seated on the washer,

4. Using pliers, tighten the couplings with

an additional two-thirds turn.

1.Hooked end

2. Drain hose

2. Put hooked end of drain hose into laundry tub or standpipe. Rotate

hook to eliminate kinks.

To prevent drain water from going

back into the washer:

• Do not straighten hooked end of drain

hose. Do not force excess drain hose into standpipe. Hose should be

secure, but loose enough to provide a gap of ain

• Do not lay excess drain hose in bot-

tom of laundry tub.

NOTE: Do not overtighten, Damage to the valves can result.

Clear the water lines

5. Run water through both faucets and

inlet hoses, into a bucket or laundry

tub, to get rid of particles in the water

lines that might clog the inlet valve

screens.

Connect the inlet hoses to the washer

6. Attach the hose with the red coupling

to the HOT (bottom) inlet valve. Attaching the red coupling first makes

it easier to tighten connection with

pliers. Screw on coupling by hand until seated on the washer, Using pli- ers, tighten the couplings with an

additional two-thirds turn. NOTE: Do not overtighten, Damage

to the valves can result.

1. Cold water inlet valve (blue)

2. Hot water inlet valve (red)

NOTE: The inlet valve may be on the right or the left side of the washer, depending on your model.

7. Attach the hose with the blue cou- pling to the COLD water (top) inlet

valve. Screw on coupling by hand until seated on the washer. Using pli- ers, tighten the couplings with an

additional two-thirds turn.

NOTE: Do not overtighten. Damage to the valves can result.

Check for leaks

8. Turn on the water faucets and check

for leaks. A small amount of water might enter the washer. You will drain

this later.

NOTE: Replace inlet hoses after 5

years of use to reduce the risk of hose failure. Record hose installation or

replacement dates for future reference.

• If you only connect one water hose, you must cap off the remain- ing water inlet port.

• Periodically inspect and replace hoses if bulges, kinks, cuts, wear,

or leaks are found.

Secure the Drain Hose

Drape the power cord over the console.

Remove any cardboard used to move washer.

Locate the remaining piece of ship- ping strap (not the end with the cotter pins) from step 3 of "Remove Shipping Strap," Use it to wrap the drain hose together with the laundry tub or standpipe. Push fastener into the nearest hole in the shipping strap.

Remaining portion of Shipping Strap

4. Wrap the drain hose to the laundry tub leg or standpipe with the tie strap. (See illustration.)

If the washer faucets and the drain standpipe are recessed, put the

hooked end of the drain hose in the standpipe. Tightly wrap the tie strap

around the water inlet hoses and the drain hose.

Level the Washer

Properly leveling your washer prevents

excessive noise and vibration.

Install the front leveling feet 1, Prop up the front of the washer about

4 in, (10.2 cm) with a wood block or similar object, The block needs to support the weight of the washer.

2, Screw the lock nut onto each foot to

within 1 in. (2.5 cm) of the base.

(2.5 cm)

3. Screw the feet into the correct holes at the front corner of the washer until

the nuts touch the washer.

NOTE: Do not tighten the nuts until the washer is level.

4, Tiltthewasherbackandremovethe 3,

woodblock.Gentlylowerthewasher tothefloor. 4,

,5. Slide to final location. 6, Check the levelness of the washer

by placing a level on the top edges of the washer; first side-to-side, then front-to-back.

If the washer is not level, move the

washer out slightly, tip back, prop up the front of the washer with the wood

block and adjust the feet up or down

as necessary. Repeat this step until washer is level.

7. After the washer is in the final loca- tion and level, use a _6in. (1.43 cm)

opemend wrench to turn the nuts on the feet tightly against the washer

cabinet.

If the nuts are not tight against the

washer cabinet, the washer may vibrate.

8. Tilt the washer forward until the rear of the washer is at least 4 in. (10.2

cm) off the floor. You may hear the self-adjusting rear feet click into

place. Lower the washer to the floor.

Complete Installation

1. Check the electrical requirements. Be sure that you have the correct electri- cal supply and the recommended grounding method. (See "Electrical

Requirements.")

2. Check to be sure all parts are now

installed. If there is an extra part, go back through the steps to see which

step was skipped.

10,

11.

Check to be sure you have all of

your tools.

Check to be sure that the yellow

shipping strap was removed from the

back of the washer and used to

secure the drain hose,

Dispose/recycle all packaging materials.

Check to be sure the water faucets

are on.

Check for leaks around faucets and inlet hoses.

Electrical Shock Hazard

Plug into a grounded

3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these

instructions can result in death, fire, or electrical shock.

Plug into a grounded 3 prong outlet. Remove the protective film on the

console and any tape remaining on the washer.

Read "Operating Your Washer."

To test your washer, measure half of the normal recommended amount of

powdered or liquid detergent and

pour it into the washer basket or detergent dispenser (on some mod- els). Close the lid, Select any cycle, and then press START. Allow it to complete one whole cycle.

To get the maximum cleaning and fabric care from your washer, please

read and follow these instructions.

NOTE: The drawings in this section show the basic features of all models covered

by this manual, Refer to the supplied "Feature Sheet" for your washer's particu-

lar features.

Never place items in the washer

Fire Hazard

that are dampened with gasoline or other flammable fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on it (including

cooking oils). Doing so can result in death,

explosion, or fire.

LID INSTRUCTIONS

These instructions are found under the lid of your washer.

Add measured detergent to the washer basket.

1. SELECT & ADJUST- Make theselections for these washer controls:

• WATER LEVEL Adjust to load size.

• WASH I RINSE TEMP ...... Selection is based on type of fabric and soil.

2. SELECT CYCLE Choose more time for heavily soiled loads and less time for lightly soiled loads.

3. PULL TIMER TO START ..... Lid must be closed to complete cycle.

PUSH TIMER TO STOR

Antiperspirants, Deodorants

Treat with a paste of ammonia and color_ safe bleach. Let stand for 30 minutes.

Wash in hottest water safe for fabric.

Blood

Rinse immediately or soak in cold water with detergent for 30 minutes. Rinse. Rub detergent into any remaining stains. Rinse thoroughly. Wash.

Milk, Ice Cream

Sponge immediately or apply a prewash soil and stain remover. Rinse. Wash.

Repeat if necessary. If stain remains, apply a few drops of liquid detergent. Rinse. If

stain remains, soak. Wash.

Grass

Use an enzyme presoak or rub enzyme detergent on the stain. Launder with deter- gent and bleach appropriate for the fabric.

Ketchup, Tomato Products

Sponge immediately or apply a prewash soil and stain remover. Rinse. Wash. If

stain remains, apply a liquid detergent to stain or soak in warm water with detergent.

Rewash.

Mud

Brush off the dry mud. Rinse under cold water. Pretreat with a paste of detergent and water. Launder using detergent and

bleach safe for the fabric.

STARTING YOUR WASHER

STEP 1, Add measured detergent

directly into washer basket. Then place a load of sorted clothes in the washer.

STEP 2. Close washer lid. STEP 3. Set WATER LEVEL Control

based on the size of your wash load.

STEP 4. Push the Cycle Selector Control (Timer) knob _) in and turn to the right.

Set cycle and time according to the type of fabric in the load.

STEP 5. Pull the Cycle Selector Control (Timer) knob O out. The dial will rotate as

the cycle progresses. The knob will

not rotate.

STOPPING/RESTARTING

WA'i_ R LEVEL WAIER _M_PERAllJRE

mNSE

_uua

M0mr

YOUR WASHER

• To stop the washer at any time, push the Cycle Selector Control (Timer)

knob _) in.

• Pull the knob out to restart.

SET WATER LEVEL CONTROL

WASH/RINSE WATER

TEMPERATURE

_i'_,J_iFm_l ;Iq i[q I]4

Your wash/rinse water temperature control is part of the Cycle Selector Control

This control gives you the flexibility to save water when washing small loads.

Your washer lets you select a water setting based on the size of your

wash load.

• For normal loads, start with a medium

(Timer) knob. All rinses are cold to save energy.

• For a HOT water wash, select SUPER.

• For a WARM water wash, select REGULAR.

• For a COLD water wash, select SHORT.

load. Adjust up or down depending on your load, Clothes should move freely and roll toward the agitator,

• To change to a higher water level setting after the washer has started to agitate, turn the knob to the desired new setting.

To select a different wash temperature and cycle (time):

STEP 1. Push in the Cycle Selector Control (Timer) knob and turn clockwise to the desired water temperature.

STEP 2. Pull out the Timer knob and allow

SMALL I L_qee the washer to fill.

STEP 3. When the washer has filled, push in the Timer knob and turn to the desired

cycle (time). STEP 4. Pull out the Timer knob.

SELECTING WATER TEMPERATURES

Wash Water Temperature Suggested Fabrics Comments

HOT • Work clothes • Best cleaning for heaviIy soiled items

111°F(44°C) • Sturdy whites/ • Removes oils, perspiration, greasy soils

or above colorfast pastels and stains

WARM • Dark/non-colorfast colors • Best for moderately soiied to tightly soiled items 90°-I 10°F • Permanent press items • Safe for most fabric finishes (32°-43°C) • Nylon, polyester, acrylics, • Less fading and dye bleeding

COLD* • Extra-sensitive colors • Best for very lightly soiled items 70°-90°F • Non-colorfast items • Saves hot water

(21°-32°C) • Hand washabies

• in wash water terr ,eratures colder than 70°F (21°0), detergents do not dissolve well. Also, soils may be difficult to remove and some fabrics may retain wear wrinkles and have

increased pilfing - the formation of small lint-like balls on the surface of garments. Pilling is

the natural result of wearing and washing of garments.

• Diapers • Prevents graying or yellowing

silks,woolens • Reduces wfinkfing

• Knits/delicate fabrics

SETTING YOUR CYCLE SELECTOR (TIMER) CONTROL

• For sturdy or heavily soiled loads, use SUPER.

• For moderately soiled loads, use REGULAR.

• For delicate or lightly soiled loads, use SHORT.

HEAVY DUTY

Use this cycle to get up to 14 minutes of wash time. Wash combines fast speed agitation and fast spin speeds.

HEAVY DUTY

PERMANENT PRESS

II''j'+++'j_'+'m"-I_lm[:__d

The PERMANENT PRESS cycle includes a load cooling process that reduces

wrinkling compared to other cycles.

Use this cycle to get up to 10 minutes of wash time. Wash combines fast speed agitation and fast spin speeds.

NOTE: When the timer reaches PAUSE, the washer will drain and pause for no

more than two minutes while some of the wash water is replaced with rinse

water.

PERMANENT

: PRESS

110 $1JPER

HOTIC_O

| RIGULAR

WArM I COLD

SHOAT

COLO i C_I_

_4m+

RINSE AND SPIN

When using extra detergent for heavily soiled clothes, or washing special-care items, you may find an extra rinse and spin is needed.

STEP 1. Set WATER LEVEL Control. STEP 2. Set the Cycle Selector Control

(Timer) knob to the RINSE setting. STEP 3. Pull Cycle Selector Control

(Timer) knob out to start washer.

SPIN ONLY

A drain and spin may help shorten drying times for some heavy fabrics or special-

care items by removing excess water,

STEP 1. Set the Cycle Selector Control

(Timer) knob to the SPIN setting,

STEP 2. Pull the Cycle Selector Control

(Timer) knob out to start washer.

UNDERSTANDING WHAT HAPPENS DURING THE WASHER CYCLE

HEAVY DUTY

selected level

Fill to

Wash

selected time

no spin Drain -

Spin

selected level

Fill to

Rinse

no spin Drain -

Spin

PERMANENT PRESS

selected level

Fill to

Wash

selected time

Partial

Drain

Pause

cool down

Fill for

Wash

no spin Drain -

Spin

Off

r_ Drain -

selected level

Fill to

Rinse

no spin

Spin

Off

STRAIGHT VANE AGITATOR

This agitator is found in Kenmore

large capacity

washers. Its design

is well-suited to handle

your everyday loads.

DUAL ACTION ®AGITATOR (On some models)

Kenmore's DUAL ACTION ® Agitator

gives you flexible fabric care for even your largest loads.

The best cleaning action in your

washer takes

place at the bot-

tom where the agitator vanes

move back and

forth to flex the fabric, loosening

the soil. To get all your clothes down

to the bottom of the washer, the

upper portion of

the agitator has

uniquely designed, spiral vanes to help push the clothes that are on top down to

the bottom. This spiraling action dis-

places the clothes that are on the bot-

tom with a "roll-over" motion.

UNDERSTANDING NORMAL

WASHER SOUNDS

Your new washer may make sounds that your old one didn't. Because the

sounds are unfamiliar, you may be concerned about them,

The following describes some of the normal sounds you may hear and what

causes them.

During Drain

The rate that water is drained from your

washer depends on your installation, If water is drained quickly from the washer,

you may hear air being pulled through the

pump. This happens during the end of draining.

After Drain and Before Spin When the cycle changes from draining

to spinning, you may hear a noise as the

gearcase shifts.

PREPARING CLOTHES FOR WASHING

Follow these recommendations

to help you prolong the life of your garments.

• Close zippers, snaps, and hooks to avoid snagging other items. Remove pins, buckles, and other hard objects

to avoid scratching the washer interior.

Remove non-washable trim and ornaments.

• Empty pockets and turn them inside out.

• Turn down cuffs, brush away lint and dirt.

• Turn synthetic knits inside out to avoid pilling.

• Tie strings and sashes so they will not tangle.

• Mend tears, loose hems, and seams.

• Treat spots and stains.

• Stained or wet garments should be

washed promptly for best results.

SORTING

• Separate heavily soiled items from lightly soiled ones, even if they

would normally be washed together. Separate lint givers (towels, chenille) from lint takers (corduroy, synthetics,

permanent press). When possible,

turn lint givers inside out.

• Separate dark colors from light colors,

colorfast items from non-colorfast items.

• Sort by fabric and construction (sturdy cottons, knits, delicate items).

rj ' TF41

Proper loading of your washer contributes to proper cleaning and

fabric care and reduces machine noise.

• Drop items into washer loosely. Fill to the top of the basket (top row of

holes). Do not wrap items around the agitator, Items should move easily through wash water for best cleaning

and wrinklefree results. Items should sink and reappear later.

• Load washer properly and select correct water level setting, Overloading or

packing the machine, and selecting a

setting too small for the wash load can:

cause poor cleaning increase wrinkling

create excessive lint wear out items faster

(because of pilling)

• Load by the amount of space items take up, not by their weight.

• Mix large and small items in each load,

Load evenly to maintain washer balance.

An off-balance load can make the washer vibrate during spin,

• Use a higher water level setting to

reduce wrinkling with permanent press

clothes and some synthetic knits, These

items should have more room to move in

the water than heavy items (towels,

jeans).

• Reduce wash time by using a lower water level setting, Loads with only a few

small items need less wash time.

LOADING SUGGESTIONS

For these suggested full-sized loads, set the WATER LEVEL selector to the

highest water level setting.

SUPER CAPACITY WASHERS

Heavy Work Clothes

4 jeans 4 workpants

4 workshirts 2 sweatshirt

2 sweatpants

Towels 10 bath towels

10 hand towels 14 wash cloths

Mixed Load

3 sheets

(I king, 2 twin)

4 pillowcases 3 shirts

3 blouses 9 T-shirts

9 shorts

10 handkerchiefs

'On some models)

EXTRA LARGE CAPACITY PLUS

WASHERS

Heavy Work Clothes

3jeans

3 workpants 2 workshJrts

1 sweatshirt 1 sweatpants

Towels

7 bath towels 8 hand towels

9 wash cloths

Mixed Load

2 sheets (1 king, 1 twin)

2 pillowcases 2 shirts

2 blouses 6 T-shirts

5 shorts 6 handkerchiefs

CLEANING YOUR WASHER

Exterior Wipe up detergent, bleach, and other spills

with a soft, damp cloth or sponge as they occur. Occasionally wipe the outside of the washer to keep it looking like new.

Do not put sharp or metal objects in your washer. They can damage the finish. Check all pockets for pins, clips, money, bolts, nuts, etc, Do not lay these objects on your washer after emptying pockets.

Interior

Clean interior with 1 cup (250 mL) of chlorine bleach mixed with 2 cups (500 mL) of detergent. Run washer through a complete cycle using hot water. Repeat process if necessary,

NOTE: Remove hard water deposits using only cleaners labeled as washer safe.

WATER INLET HOSES

Replace inlet hoses after five years

of use to reduce the risk of hose failure. Periodically inspect and

replace inlet hoses if bulges, kinks, cuts, wear, or leaks are found, When

replacing your inlet hoses, mark the date of replacement on the label with a permanent marker.

WINTER STORAGE

OR MOVING CARE Install and store your washer where

it will not freeze, Because some water may stay in the hoses, freezing can

damage your washer, If storing or moving your washer during freezing

weather, winterize it,

To winterize washer:

1. Shut off both water faucets,

2. Disconnect and drain water inlet hoses.

3. Put 1 qt (1 L) of R.V.-type antifreeze in the basket,

4. Run washer on a SPIN setting for about 30 seconds to mix the antifreeze

and water. Some of the mixture will pump out while the washer spins.

5. Unplug washer or disconnect power. To use washer again:

1. Flush water pipes and hoses,

2. Reconnect water inlet hoses.

3. Turn on both water faucets,

4. Plug in washer or reconnect power,

5. Run the washer through a complete cycle with 1 cup (250 mL) of detergent

to clean out antifreeze.

NON-USE OR VACATION CARE Operate your washer only when you are

at home, If you will be on vacation or not using your washer for an extended period of time, you should:

• Unplug washer or disconnect power.

• Turn off the water supply to the washer.

This helps avoid accidental flooding

(due to a water pressure surge) while

you are away.

Most laundering problems are easily solved if you understand the cause. Check these lists for common laundry and washer problems. If you need further assis- tance, see service and assistance information on back cover.

Problem Possible Cause Solution

Washer Leaks Household plumbing is leaking. Repair plumbing.

Inlet hoses not tight. Tighten hoses (see "Installation

Instructions").

Inlet hose washers not Reseat washers (see"Installation

properly seated. Instructions"). Drain hose not propedy Clamp drain hose (see "Installation

clamped or is off. Instructions"). Drain is clogged. Remove drain clogs. Sink, standpipe,

or floor drain must be able to handle

17 gaI (64 L) of water per minute.

Tub moved forward during Ensure tub is centered before unloading, causingwater starting washer. to deflect off tub ring.

Unit not level causing water Ensure front feet are installed and to deflect off tub ring. nuts are tightened. Levelwasher.

Reset rear legs (see "Installation

Instructions").

Load is unbalanced. Spray Redistribute the load. rinses are deflecting off load.

Washer is overloaded. Fills Reduce load size. or spray rinses are deflecting

off load.

Won't Drain/ Drain hose is kinked or Straighten or unplug hose (see Won't Spin/ clogged. "Installation Instructions").

Wet Loads

Correct operation of After awash or rinse, the washer will neutral drain, drainwithout spinning. After draining,

the spinning begins. Lid is open. Close the Iid. Drain hose is more than Lower drain hose (see "Installation

96 in. (2,4 m) above the floor. Requirements"), Too much detergent - Use Isss detergent.

excessive sudsing. Low voltage or using an Check electrical source or call

extension cord. electrician. Do not use extension

cords. Cold rinses. Cold rinses leave loads wetter than

warm rinses. This is normal.

Problem Possible Cause Solution

Continues Drain hose is less than Raise the drain hose (see

to Fill/ 39 in.(99 cm) above floor. "Installation Requirements"),

Continues

to Drain/ Drain hose fits tightly into Adjust drain hose for loose fit (see

Cycle Stuck standpipe. "Installation Instructions"),

Drain hose taped into Do not seal off drain hose with tape. standpipe. The drain hose needs an air gap.

Washer Makes Load is unbalanced. Redistribute load. Noise

Washer is not level. Level washer. Reset rear legs (see Rear leveling legs not set. "Installation Instructions"),

Nuts on front feet not tight. Tighten nuts (see "Installation

Instructions").

Yellowshipping strapwith Remove strap with cotter pins cotter pins not completely (see "Installation Instructions"),

removed. Floor not strong enough Relocate washer (see "Installation

to support washer. Requirements"), Gears engaging after drain This is normal.

and before spin. Upper part of agitator clicks This is normal.

during wash,

Won't Water inlet valve Clean screens.

Fill/Won't screens are plugged. Rinse/Won't

Agitate/ Water is turned off. Turn on water. Wrong Hot and cold hoses are Reverse hoses (see "Installation

Temperature reversed, Instructions"),

Inlet hose is kinked. Straighten hoses.

Timer diaI is not lined up. Turn timer knob to the right slightly

and pull to start. Power cord not plugged in, Plug into a grounded 3 prong outlet.

Problem Possible Cause Solution Machine Power cord not plugged in. Plug into a grounded 3 prong outlet.

Stops

No power at plug. Check electrical source or call

eIectrician. Fuse blown or circuit Replace fuse or reset circuit breaker.

breaker open. Ifproblem continues, calI electrician. Using an extension cord. Do not use extension cords. Timer is not lined up. Turn timer to the right slightly

and pull to start. Timer knob not pulled out. Set and pullout knob.

Machine is overloaded. Wash smaller Ioads.

Agitator Not The top of the agitator moves This is normal. Working only in one direction.

The top of the agitator is loose. This is normal.

Water Level The top of the agitator is much This is normal. Too Low/Not higher than the highestwater Completely level. This creates a perception

Filling of the washer not beingfuIl.

Tub is Tub pulled forward when Ensure tub is centered before Crooked unloading, starting washer.

Tub moves. This is normal. Unit not level. Ensure front feet are installed and

nuts are tightened. Levelwasher.

Reset rear legs (see "Installation

Instructions").

Lint on Load Improper sorting. Sort lint givers from lint takers

and by color. Overloading. Lint can be trapped in load if

overloaded. Wash smaller loads, Paper or tissue in pockets. Clean out pockets before washing,

Not enough detergent. Use enough detergent to

hold lint in water. Detergent not dissolving. Use wash water warmer than

Watertemperaturelowerthan 70°F (21°C). 70°F (21°C).

Problem Possible Cause Solution

Tearing Overloading. improper Loads should movefreely during

use of washer, wash. Wash smaller loads.

Improper use of chlorine Do not pour chlorine bleach directly bIeach. Undiluted bleach on load.Wipe up bleach spills. will damage fabrics.

Sharp items not removed Cleanout pockets before washing. from pockets;fasteners Zip zippers before washing.

not fastened.

Itemsdamaged before Mend rips and broken threads in washing, seams before washing.

Stains on Improper use of fabric Dilute fabric softener and add to

Load softener in washer or dryer, deep rinseonly.

Iron in water (rust). InstaIIan iron filter. Under use of detergent causing Use enough detergent to remove

soiIto be redeposited, soil and hold it in suspension. Dye transfer due to not Sort dark clothing from whites

sorting Ioadsproperly, and lights. Dye transfer due to not Unload the washer as soon as

unloading washer promptly, it stops.

Load is Not removing load promptly. Unload the washer as soon as it stops.

Wrinkled

Overloading. Loads should move freely during

wash. Wash smaller loads.

Hoses reversed. Reverse hoses (see "Installation

Instructions").

Load is Overloading. Loads should move freely during

Tangled/ wash. Wash smaller loads. Twisted

Clothes wrapped around Do not wrap items around agitator agitator, when loading the washer.

WE SERVICE WHAT WE SELL

Your purchase has added value because you can depend on Sears Home CentraP, for service. With over 12,000 trained repair specialists and access to over 4.2

million parts and accessories, we have the tools, parts, knowledge and skills to

ensure our pledge: We Service What We Sell.

Sears Maintenance Agreements

Your Kenmore appliance is designed, manufactured and tested to provide years of dependable operation. Yet any major appliance may require service from time to time, The Sears Maintenance Agreement offers you an outstanding service program, affordably priced.

The Sears Maintenance Agreement

• Is your way to buy tomorrow's service at today's price.

• Eliminates repair bills resulting from normal wear and tear.

• Provides for non-technical and instructional assistance.

• Even if you don't need repairs, provides an annual Preventive Maintenance Check, at your request, to ensure that your appliance is in proper running

condition.

Some limitations apply. For more information, call 1-800-827-6655.

For information concerning Sears Canada Maintenance Agreements,

call 1-800-361-6665

+ 61 hidden pages