Kenmore 1101820296 Owner’s Manual

24" (61 cm) Wide

LAUNDRY CENTER

Washer - Electric Dryer

ENSEMBLE DE BUANDERIE

de 24" (61 cm) de largeur

Laveuse - S_cheuse _lectrique

Models/Mod61es 11 0.C18202

W10035020 Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8 www.sears.ca

TABLEOF CONTENTS

MAINTENANCE

MAINTENANCE AGREEMENTS .................................................... 2

WARRANTY ..................................................................................... 3

WASHER/DRYER SAFETY ............................................................ 4

INSTALLATION INSTRUCTIONS .................................................. 5

Tools and Parts ............................................................................ 5

Alternate Parts .............................................................................. 5

Location Requirements ................................................................ 6

Drain System ................................................................................ 7

Electrical Requirements ................................................................ 7

Venting Requirements .................................................................. 8

Install Leveling Legs ..................................................................... 9

Remove Foam Packing ................................................................ 9

Connect Drain Hose ..................................................................... 9

Connect Inlet Hoses .................................................................. 10

Secure Drain Hose .................................................................... 11

Plan Vent System ...................................................................... 11

Install Vent System .................................................................... 12

Level Laundry Center ................................................................ 12

Connect Vent ............................................................................. 13

Complete Installation ................................................................. 13

WASHER USE .............................................................................. 14

Starting Your Washer ................................................................ 14

Cycles ........................................................................................ 15

Rinse and Spin .......................................................................... 15

Drain and Spin ........................................................................... 15

Understanding Washer Cycles .................................................. 15

Normal Sounds .......................................................................... 16

LAUNDRY TIPS ............................................................................ 18

Loading ...................................................................................... 16

DRYER USE ................................................................................. 17

Starting Your Dryer .................................................................... 17

Stopping and Restarting ........................................................... 17

Loading ...................................................................................... 17

Drying, Cycle and Temperature Tips ........................................ 18

Cycles ........................................................................................ 18

LAUNDRY CENTER CARE ......................................................... 19

Cleaning the Laundry Center Location ..................................... 19

Cleaning Your Washer ............................................................... 19

Water Inlet Hoses ...................................................................... 19

Cleaning the Lint Screen ........................................................... 19

Cleaning the Dryer Interior ........................................................ 20

Removing Accumulated Lint ..................................................... 20

Vacation, Storage and Moving Care ......................................... 20

TROUBLESHOOTING WASHER ................................................ 21

TROUBLESHOOTING DRYER .................................................... 23

AGREEMENTS

Maintenance Agreements

Your purchase has added value because you can depend on Sears HomeCentraP for service. With over 2,400 Service Technicians and more than a million parts and accessories, we have the tools, parts, knowledge and skills to back our pledge:

We Service What We Sell. Your Kenmore ®product is designed, manufactured and tested to

provide years of dependable operation. But like all products, it may require service from time to time. The Sears Maintenance Agreement offers you an outstanding service program, affordably priced.

The Sears Maintenance Agreement

• Is your way to buy tomorrow's service at today's price

• Eliminates repair bills resulting from normal wear and tear

• Provides phone support from a Sears technician on products requiring in-home repair

• Even if you don't need repairs, provides an annual Preventive Maintenance Check, at your request, to ensure that your product is in proper running condition.

Some limitations apply. For more information about Sears Canada Maintenance Agreements, call 1-800-381-6865.

KENMORE APPLIANCE WARRANTY

ONE YEAR LIMITED WARRANTY

When installed, operated and maintained according to all instructions supplied with the product, if this appliance fails due to a defect in material or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME ®to arrange for free repair.

If this appliance is used for other than private family purposes, this warranty applies for only 90 days from the date of purchase.

THIS WARRANTY COVERS ONLY DEFECTS IN MATERIAL AND WORKMANSHIP. SEARS WILL NOT PAY FOR:

1. Expendable items that can wear out from normal use,

including but not limited to filters, belts, light bulbs, and bags.

2. A service technician to instruct the user in correct product installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed, operated or maintained according to all instructions supplied with the product.

5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

Customer's sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Implied warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law. Sears shall not be liable for incidental or consequential damages. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitations on the duration of implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to you.

This warranty applies only while this appliance is used in the United States and Canada.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co.

Dept. 817WA, Hoffman Estates, IL 60179

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2B8

PRODUCT RECORD

In the space below, record your complete model number, serial number, and purchase date. You can find this information on the model and serial number label located on the product.

Have this information available to help you obtain assistance or service more quickly whenever you contact Sears concerning your appliance.

Model number

Serial number

Purchase date

Save these instructions and your sales receipt for future

reference.

WASHER/DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer/dryer, follow basic

precautions, including the following:

[] Read all instructions before using the washer/dryer. [] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

[] Do not wash or dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or explode.

[] Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

[] Do not allow children to play on or in the washer/dryer.

Close supervision of children is necessary when the washer/dryer is used near children.

[] Before the washer/dryer is removed from service or

discarded, remove the doors to the washer/dryer compartments.

[] Do not reach into the washer/dryer if the tub, agitator or

drum is moving.

[] Do not install or store the washer/dryer where it will be

exposed to the weather. [] Do not tamper with controls. [] Clean dryer lint screen before or after each load.

[] Under certain conditions, hydrogen gas may be produced in

a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water

system has not been used for such a period, before using the washing machine, turn on all hot water faucets and let the water flow from each for several minutes. This will

release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this

time.

[] Do not repair or replace any part of the washer/dryer or

attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair

instructions that you understand and have the skills to carry

out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the machine and dryer exhaust vent should

be cleaned periodically by qualified service personnel.

[] See "Electrical Requirements" section for grounding

instructions.

SAVE THESE INSTRUCTIONS

INSTALLATION INSTRUCTIONS

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

Tools needed:

#2 Phillips and flat-blade screwdriver

Adjustable wrench that opens to 1" (2.5 cm) or 9/16"open-end wrench (for adjusting dryer feet)

1A"nut driver or socket wrench

Tin snips (for new vent installations)

Parts supplied:

Remove parts package from the washer basket. Check that all parts were included.

• Caulking gun and compound (for installing

new exhaust vent)

• Level

• Knife

• Vent clamps

• Pliers

• Scissors

• Wood block (for leveling)

• Ruler or measuring tape

Parts listed are available from your local Sears store or Sears Service Center. For further information, please call

1-800-4-MY-HOME® (1-800-469-4663).

If You Have You Will Need to Buy

Laundry tub or Sump pump system (if not already standpipe taller than available) 96" (2.4 m)

1" (2.5 cm) diameter 2" (5 cm) diameter to 1" (2.5 cm) standpipe diameter standpipe adapter, Part

Number 3363920

Overhead sewer Standard 20 gal. (76 L) 34" (86.4 cm)

tall drain tub or utility sink and sump

pump (available from local plumbing suppliers)

Floor drain Siphon break, Part Number 285320,

additional drain hose, Part Number 285702 and connector kit, Part Number 285442

Drain hose too short Drain hose, Part Number 285664 and

connector kit, Part Number 285442

Lint clogged drain Drain protector, Part Number 367031

B C D

E F

A. Water inlet hoses (2) B. Inlet hose flat washers (4) C. Rear leveling legs D. Front leveling legs (2)

Parts needed:

Check local codes, electrical supply and venting, and read "Electrical Requirements" and "Venting Requirements" before purchasing parts.

Mobile home installations require metal exhaust system hardware available for purchase from your local Sears store or Sears Service Center. For further information, please call 1-800-4-MY-HOME ®(1-800-469-4663}.

E. Plastic strap F Drain hose

G. Yellow, single wire hose clamp H. Silver, double-wire hose clamp

Water faucets 2 longer water fill hoses: beyond reach of fill 6 ft (1.8 m) Part Number 76314, hoses 10 ft (3.0 m) Part Number 350008

ExplosionHazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Failure to do so can result in death, explosion, or fire.

You will need

• A location that allows for proper exhaust installation. See

"Venting Requirements."

• A grounded electrical outlet located within 2 ft (61 cm) of either side of the laundry center. See "Electrical Requirements."

• A sturdy floor to support the laundry center weight (laundry center, water and load) of 500 Ibs (226.8 kg).

A level floor with a maximum slope of 1" (2.5 cm) under entire laundry center. Clothes may not tumble properly and automatic sensor cycles may not operate correctly if laundry center is not level. Installing on carpet is not recommended.

• A water heater set to deliver 120°F (49°C) water to the washer.

• Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 5-100 psi (34.5-689.6 kPa).

The laundry center must not be installed or stored in an area where it will be exposed to water and/or weather.

Do not operate your washer in temperatures at or below • 32°F (0°C). Some water can remain in the washer and can cause

damage in low temperatures. See "Vacation, Storage and Moving • Care" for winterizing information.

Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times. •

Check code requirements. Some codes limit, or do not permit, installation of the laundry center in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.

Installation Clearances

The location must be large enough to allow the dryer door to open fully.

Laundry Center Dimensions

15%"

(39.05 cm)

71 ¾"

(192.25 cm)

32%"

81.6 cm)

23 T/8

(60.64 cm)

*Most installations require a minimum 51/2'' (14 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting Requirements."

Minimum installation spacing for recessed area or closet installation

The following dimensions shown are for the minimum spacings allowed.

• Additional spacing should be considered for ease of installation and servicing.

Additional clearances might be required for wall, door and floor moldings.

For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

Rear clearance may be 1" (2.5 cm) when house exhaust system is lined up directly with dryer exhaust.

__ 1"

_. (2.5cm)i

48in.z

(3100rn2)I

"NNN-t

3" (7.6crn)

1" _,,-)_- 23%"-_-1" -_ 1" _e 27Y_"-_,-

(2.5cm) (60.64cm) 2.5cm 2,5cm (69.22cm)

A B

A. Recessed area B. Side view - closet or confined area C. Closet door with vents

24inY

(155cm=)I

_- 5½"

(14¢rn)

__' (7.6cm)

Mobile Home - Additional Installation Requirements

This laundry center is suitable for mobile home installations. The installation must conform to the Canadian Manufactured

Home Standard, CAN/CSA-Z240 MH. Mobile home installations require:

• Metal exhaust system hardware, which is available for purchase from your local Sears store or Sears Service Center.

Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.

The laundry center can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need.

See "Alternate Parts."

Standpipe drain system - wall or floor (views A & B)

The standpipe drain requires a minimum diameter standpipe of • 2" (5 cm). The minimum carry-away capacity can be no less than

17 gal. (64 L) per minute. A 2" (5 cm) diameter to 1" (2.5 cm) diameter standpipe adapter kit is available. See "Alternate Parts."

The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (2.4 m) from the bottom of the washer. •

E ect ca R< s 'sme sts

Electrical Shock Hazard

Plug into a grounded 4 prong outlet. Failure to do so can result in death or electrical shock.

Itis your responsibility

• Tocontact a qualified electrical installer.

To be sure that the electrical connection is adequate and in conformance with the Canadian Electrical Code, C22.1 -latest edition and local codes. A copy of the above codes standard may be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

To supply the required 4 wire, single phase, 115/230 volt, 60 Hz., AC only electrical supply on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or

circuit breaker is recommended. Connect to an individual branch circuit.

This dryer is equipped with a CSA International Certified Power Cord intended to be plugged into a standard 14-30R wall receptacle. The cord is 5 ft (1.52 m) in length. Be sure wall receptacle is within reach of dryer's final location.

Laundry tub drain system (view C) The laundry tub needs a minimum 20 gal. (76 L) capacity. The top

of the laundry tub must be at least 34" (86.4 cm) above the floor and no higher than 96" (2.4 m) from the bottom of the washer.

Floor drain system (view D)

The floor drain system requires a siphon break that may be purchased separately. See "Alternate Parts."

The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer. Additional hoses might be needed.

C D

4-wire receptacle 14-30R

• Do not use an extension cord. If using a replacement power supply cord, it is recommended

that you use Power Supply Cord Replacement Part Number

9831317. For further information, please call 1-800-4-MY-HOME ®

(1-800-469-4663).

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected washer/dryer: This washer/dryer must be grounded. In the event of

malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for

electric current. This washer/dryer is equipped with a cord having an equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with

all local codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the washer/dryer is properly grounded. Do not modify the plug provided with the washer/dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

Fire Hazard

Use a heavy metal vent. Do not use a plastic vent.

Do not use a metal foil vent. Failure to follow these instructions can result in death

or fire.

• Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor performance.

• Do not install flexible metal vent in enclosed walls, ceilings or floors.

Elbows

45° elbows provide better airflow than 90° elbows.

Good Better

WARNING: To reduce the risk of fire, this laundry center

MUST BE EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances,

The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling or a concealed space of a building.

If using an existing vent system

• Clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint,

• Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.

• Review Vent system chart. Modify existing vent system if necessary to achieve the best drying performance.

If this is a new vent system

Vent material

• Use a heavy metal vent. Do not use plastic or metal foil vent.

• 4" (10.2 cm) heavy metal exhaust vent and clamps must be used. DURASAFE TM venting products are recommended.

Clamps

• Use clamps to seal all joints.

• Exhaust vent must not be connected or secured with screws or other fastening devices that extend into the interior of the

duct. Do not use duct tape.

Clamp

Exhaust

Recommended hood styles are shown here.

(10.2 cm)

A.Louvered hood style B.Box hood style

The angled hood style (shown here) is acceptable.

4" (!0.2 cm) heavymetal exhaust vent

DURASAFE TM vent products can be purchased from your dealer. For further information, please call

1-800-4-MY-HOME (1-800-469-4663) orvisit our website at

www.sears.ca.

Rigid metal vent

• For best drying performance, rigid metal vents are recommended.

• Rigid metal vent is recommended to avoid crushing and kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for cleaning.

• Flexible metal vent must be fully extended and supported when the laundry center is in its final position.

An exhaust hood should cap the vent to keep rodents and insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.).

• Do not use an exhaust hood with a magnetic latch.

Improper venting can cause moisture and lint to collect indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint,

wallpaper, carpets, etc.

[] Housecleaning problems and health problems.

Excessive Weight Hazard

Use two or more people to move and install washer/dryer.

Failure to do so can result in back or other injury.

To protect the floor, use a large flat piece of cardboard from the shipping carton. Gently place the laundry center on its side, on

the cardboard.

Install the rear leveling legs

1. Push legs into holes in rear corners until they snap into place.

2. Check adjustability of rear legs by pushing in one leg. The other leg should come out. Check both legs. If they do not move freely, repeat Step 1.

Install the front leveling legs

1. Examine the front leveling legs. Find the diamond marking.

2. Screw front legs by hand, into the holes in the triangular braces in the front corners. Use wrench to finish turning the legs until the diamond marking is no longer visible.

Proper connection of the drain hose protects your floors from damage due to water leakage, To keep the drain hose from coming off or leaking, it must be installed according to the following instructions:

IMPORTANT: To ensure proper installation, this procedure must be followed exactly.

1. Check the drain hose to see whether it is the proper length.

2. Wet the inside of the straight end of the drain hose with tap water.

IMPORTANT: Do not use any lubricant other than water.

3. Squeeze ears of the silver, double-wire clamp with pliers to open. Place clamp over the straight end of the drain hose _A"(6.4 mm) from the end.

Open clamp. Twist hose back and forth while pushing onto drain connector on the side of the laundry center. Continue until hose contacts the ribbed stops on the cabinet.

3. Stand the laundry center upright.

1. Open the washer lid. The latch under the dryer will keep the lid open.

2. Pull the foam packing ring out of the washer.

NOTE: Keep the foam ring and use it when transporting your laundry center. This packing material is used to keep the washer tub stable during transport.

5. Place clamp over the area marked "CLAMR" Release clamp.

For laundry tub or standpipe drain systems

1. Open the yellow, single-wire clamp and slide over the hooked

end of the drain hose to secure the rubber and corrugated sections together.

A. Hooked end B. Drain hose

2. Put the hooked end of drain hose into laundry tub or standpipe. Rotate hook to eliminate kinks.

To keep drain water from going back into the washer:

• Do not straighten hooked end of the drain hose and force excess drain hose into standpipe. Hose should be secure but loose enough to provide a gap for air.

• Do not lay excess hose on the bottom of the laundry tub.

3. Using pliers, tighten the couplings with an additional two- thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

For use with floor drain Remove the drain hose hook from the corrugated drain hose. You

may need additional parts. See Floor drain under "Alternate Parts."

Insert a new flat washer (supplied) into each end of the inlet

hoses. Firmly seat the washers in the couplings.

A B

A. Coupling

B.Washer

Connect the inlet hoses to the water faucets Make sure the washer basket is empty.

2. Attach the hose labeled hot to the hot water faucet. Screw on coupling by hand until it is seated on the washer.

3. Attach the hose labeled cold to the cold water faucet. Screw on coupling by hand until it is seated on the washer.

4. Using pliers, tighten the couplings with an additional two- thirds turn.

i ....A

A. Cold water inlet valve (top) B. Hot water inlet valve (bottom)

4. Attach the cold water hose to the top inlet valve.

5. Screw on coupling by hand until it is seated on the washer.

6. Using pliers, tighten the couplings with an additional two- thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

If you are working in a closet or recessed area Move the laundry center into its final position and remove

cardboard from under laundry center. Remove the access panel by removing 3 Phillips-head screws and one bumper, located at the top of the access panel. Set panel, screws and bumper aside. Complete hookup of water hoses and (on gas models) the flexible gas connector through the access area. Replace access panel upon completion of laundry center installation.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

Clear the water lines

• Run water through both faucets and inlet hoses, into a laundry tub, drainpipe or bucket to get rid of particles in the water lines that might clog the inlet valve screens.

• Check the temperature of the water to make sure that the hot water hose is connected to the hot water faucet and that the

cold water hose is connected to the cold water faucet.

Connect the inlet hoses to the washer

1. Attach the hot water hose to the bottom inlet valve. Attaching

the hot water hose first makes it easier to tighten connection with pliers.

2. Screw on coupling by hand until it is seated on the washer.

Check for leaks

7. Turn on the water faucets and check for leaks. A small amount of water might enter the washer. You will drain this

later.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement dates for

future reference.

• If you connect only one water hose, you must cap off the remaining water inlet port.

• Periodically inspect and replace hoses if bulges, kinks, cuts, wear or leaks are found.

• The apparatus must be connected to the water faucets using the new hoses. Do not use old hoses.

Move the laundry center to its final location and remove any cardboard used to move the laundry center.

Locate the plastic strap included in the parts package.

(22

Beaded tiestrap

Wrap the drain hose to the laundry tub leg or standpipe with the plastic strap (A or B below) and secure.

A B C

If the water faucets and the drain standpipe are recessed, put the hooked end of the drain hose in the standpipe. Tightly wrap the plastic strap around the water inlet hoses and the drain hose (C above).

Optional exhaust installations

This laundry center can be converted to exhaust out the right or left side. To convert the laundry center, use Side Exhaust Kit Part Number 279823. If your laundry center was previously exhausted from the right or left side, it can be converted to rear exhaust by using standard offset connections. To cover the hole in the side, one of the following plugs can be added:

692790 (white) 3979370 (graphite) 3977784 (biscuit)

Follow the instructions in the kit to install. Kits are available from your local Sears store or Sears Service Center.

•T•LT i

B C

A. Standard rear offset exhaust installation B. Rear exhaust for offset close clearance connection

C. Left or right side exhaust installation

Choose your exhaust installation type

Recommended exhaust installations

Typicalinstallations vent the dryer from the rearof the washer/ dryer. Other installations arepossible.

A _ ..................b

,KLN:r: E

A. Dryer

B. Rigid metal or flexible metal vent

C. Clamps

D. Wall

E. Elbow

F. Clamps

G. Elbow H. Exhaust hood

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for your installation. Three close-clearance installations are shown. Refer to the manufacturer's instructions provided with the vent system.

....L-R_-IN--- ....[--A:A- -'

.........

", i ",. i

,,j......... ,,,..........

A B C

A. Loop system with standard elbows B. Loop system with one offset and one standard elbow

C. Vent system with one periscope (2" [5 cm] clearance)

NOTE: The following kits for close clearance alternate installations are available for purchase. To order, please call

1-800-4-MY-HOME ®(1-800-469-4663}.

Over-the-Top Installation: Part Number 26-49900

Periscope Installation (For use with dryer vent to wall vent mismatch):

Part Number 26-49901 - Less than 5" (12.7 cm) mismatch Part Number 26-49908 - 5" (12.7 cm) to 18" (45.7 cm)

mismatch Part Number 26-49904 - 18" (45.7 cm) to 29" (73.7 cm)

mismatch Part Number 26-49905 - 29" (73.7 cm) to 50" (127 cm)

mismatch

Special provisions for mobile home installations The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside.

Determine vent path

• Select the route that will provide the straightest and most direct path outdoors.

• Plan the installation to use the fewest number of elbows and turns.

• When using elbows or making turns, allow as much room as possible.

• Bend vent gradually to avoid kinking.

• Use the fewest 90 °turns possible.

• Reduce performance, resulting in longer drying times and increased energy usage.

The Vent system chart provides venting requirements that will help to achieve the best drying performance.

Vent system chart NOTE: Side exhaust installations add a 90° turn inside the

laundry center. To determine maximum exhaust length, add one 90° turn to the chart.

Number of Type of Vent Box or Angled

90° turns Louvered hoods or elbows hoods

0 Rigid metal 43 ft (13.1 m) 36 ft (11.0 m)

Flexible metal 30 ft (9.1 m) 24 ft (7.3 m)

1 Rigid metal 33 ft (10.1 m) 26 ft (7.9 m)

Flexible metal 24 ft (7.3 m) 18 ft (5.5 m)

2 Rigid metal 24 ft (7.3 m) 16 ft (4.9 m)

Flexible metal 16 ft (4.9 m) 10 ft (3.0 m)

Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.

Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

Run vent to dryer location. Use the straightest path possible. See "Determine vent path" in "Plan Vent System." Avoid 90° turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the interior

of the vent to secure vent.

Lew? b%,}"K Oet "tel

Properly leveling your laundry center averts excessive noise and vibration.

1. Check the levelness of the laundry center by placing a level on the top edge of the washer, first side to side, then front to

back.

Determine vent length and elbows needed for best

drying performance

• Use the Vent system chart below to determine type of vent material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust systems longer than those

specified will:

• Shorten the life of the dryer.

If the laundry center is not level, prop up the front with a wood block and adjust the feet up or down as necessary. Remove wood block and lower laundry center. Repeat this step until the laundry center is level.

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in laundry center. If connecting to existing vent, make sure the

vent is clean. The vent must fit over the exhaust outlet and inside the exhaust hood. Make sure the vent is secured to

exhaust hood with a 4" (10.2 cm) clamp.

2. Move laundry center into its final position. Do not crush or kink vent. Make sure laundry center is level.

1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped,

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials, Keep the plastic foam for use if the laundry center should be transported.

4. Check the laundry center's final location. Be sure the vent is not crushed or kinked,

5. Check that the laundry center is level and front leveling feet are tight. See "Level Laundry Center."

6. Plug into a grounded 4 prong outlet. Turn on power.

7. Check that the water faucets are on.

8. Check for leaks around faucets and inlet hoses.

9. Remove the blue protective film on the console and any tape remaining on the laundry center.

10. Read "Washer Use" and "Dryer Use."

11. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.

12. To test the washer, measure _/2the normal recommended amount of detergent and pour it into the washer. Close the lid. Select HEAVY DUTY and pull out the Cycle Control knob. Allow the washer to complete one whole cycle.

13. To test the dryer, set the dryer on a full heat cycle (not an air cycle) for 20 minutes and start the dryer.

If the dryer will not start, check the following:

• Controls are set in a running or "On" position.

• Start button has been firmly pushed.

• Laundry center is plugged into a grounded outlet.

• Electrical supply is connected.

• Household fuse is intact and tight, or circuit breaker has

not tripped.

• Dryer door is closed.

14.

When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you feel heat, cancel cycle and

close the door.

If you do not feel heat, turn off the dryer and check the following:

• There may be 2 household fuses or circuit breakers for

the dryer. Check to make sure both fuses are intact and tight, or that both circuit breakers have not tripped. If there is still no heat, contact a qualified technician.

NOTE: You may notice a burning odor when dryer is first heated. This odor is common when the heating element is first used. The odor will go away.

WASHER USE

HEAVY DUTY SHORT

SPIN .........................................................................10 REGULAR

GENTLE WATERTEMP WATERLEVEL

RINSE PERMANENT MEDIUM

PRESS COLDWARM LL_

SHORT 8

REGULAR10- SPIN

SUPER 12 -

KNiT/DELiCATE

RINSE

SOAK_

Fire Hazard

Never place items in the washer that are dampened with gasoline or other flammable fluids.

No washer can completely remove oil. Do not dry anything that has ever had any type of oil on

it (including cooking oils). Doing so can result in death, explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

The following is a guide to starting your washer. Periodic references to other sections of this manual provide more detailed

information.

1. Pour measured powdered or liquid detergent into the washer. Ifdesired, add powdered or liquid color safe bleach.

2. Place a load of sorted clothes in the washer.

• Load evenly to maintain washer balance. Mix large and small items. See "Loading."

• Items should move easily through the wash water. Overloading can cause poor cleaning.

Close the washer lid.

Turn the WATER LEVEL selector knob to the correct setting for your wash load and the type of fabric being washed.

WATER LEVEL

M_OlUM

LOA_

SMALL LA_E

_SF

LOA_UlA_O o

WARM WARM LOAD

e RESET

COLD __e • HOT LOAD_ LOAD

COLD__COLD

SMALL LARGE

• Choose a load size that allows the load to move freely for best fabric care. See "Loading."

• You may change the load size selection after the washer has started filling by turning the selector to a different setting.

Set the WATER TEMP selector to the correct setting for the type of fabric and soils being washed.

Use the warmest water safe for the fabric. Follow garment label instructions.

Water Temp Use For

Hot Whites and pastels

Warm Bright colors

Cold Colors that bleed or fade

NOTE: In wash water temperatures colder than 60°F (15.6°C), detergents do not dissolve well. Soils can be difficult to

remove. Some fabrics can retain wear wrinkles and have increased pilling (the formation of small lint-like balls on the

surface of garments).

Push in the Cycle Control knob and turn it clockwise to the wash cycle you want. Pull out the Cycle Control knob to start

the washer.

To stop or restart your washer:

• To stop the washer at any time, push in the Cycle Control knob.

• To restart the washer, close the lid (if open) and pull out the Cycle Control knob.

WATER TEMP

WARM WARM

C0LI} WARM

COLD e • HOT

COLDe CO_;LD

Heavy soils

Moderate to light soils

Light soils

This section describes the available wash cycles and will help you make the best cycle selections for your wash loads. Each cycle is designed for different types of fabric and soil levels.

• The washer pauses briefly throughout each cycle. These pauses are normal. Refer to "Normal Sounds" for sounds you may hear during a wash cycle.

• Refer to "Understanding Washer Cycles" to learn what happens during a wash cycle.

.....................................................................................10 REGULAR

HEAVY DUTY

RINSE

SPIN

PERMANENT PRESS

RINSE

Soak The Soak cycle features 4 minutes of agitation followed by an

unlimited soak time to help remove heavy soils and stains that need pretreatment. You will need to reset the washer to a SPIN setting to remove water.

• The Soak cycle should be followed by the Heavy Duty or Permanent Press or Prewash cycle with additional detergent.

NOTE: Hot water is not recommended for soaking. It may set some stains.

Prewash

Use this cycle to get up to 4 minutes of agitation to help remove heavy soils and stains that need pretreatment.

• The Prewash cycle should be followed by the Heavy Duty or Permanent Press cycle with additional detergent.

SPIN

KNIT/DEL(CATE

SOAK

Heavy Duty

Use this cycle for sturdy or heavily soiled loads. Wash combines fast-speed agitation and fast-spin speeds.

• Use the Super or Regular settings for heavily soiled and sturdy fabrics.

• Use the Short setting for light soil and sturdy fabrics.

Permanent Press

The Permanent Press Cycle includes a load-cooling process that reduces wrinkling. Wash combines fast and slow-speed agitation and slow spin speeds.

When the timer reaches Pause, the washer will drain and pause for approximately 2 minutes while some of the wash water is drained and replaced with rinse water.

Knit/Delicate Use this cycle for lingerie and loosely knit items. Partway through

the cycle, the washer pauses and soaks the load for gentler care of lightly soiled delicate items. Wash combines slow-speed agitation for gentle soil removal and slow spin speeds to reduce wrinkling.

When using extra detergent for heavily soiled clothes, or washing special-care items, you may find an extra rinse and spin is

needed.

1. Push in the Cycle Control knob and turn it clockwise to any of the RINSE settings.

• For fast agitation and spin, use the Heavy Duty cycle.

• For slow agitation and spin, use the Permanent Press

cycle.

2. Set the WATER LEVEL and WATER TEMP controls to the desired setting.

3. Pull out the Cycle Control knob. The washer fills to the selected load size, agitates, drains, and spins.

A drain and spin may help shorten drying times for some heavy fabrics or special-care items by removing excess water.

1. Push in the Cycle Control knob and turn it clockwise to any of the SPIN settings.

• For a fast spin, use the Heavy Duty cycle.

• For a slow spin, use the Permanent Press cycle.

2. Pull out the Cycle Control knob. The washer drains, then spins.

When the Cycle Control knob is set to a cycle and pulled out, the washer fills (to the selected load size) before agitation and timing start. The washer begins agitating immediately after filling; agitation occurs with the washer lid down.

During agitation, the agitator creates a continuous reliever action that provides a thorough cleaning of the wash load.

After agitation starts, the Cycle Control knob turns clockwise until it points to an Off area and the cycle ends.

+ 33 hidden pages