Kenmore 1069557682, 1069557652, 1069557611, 1069555983, 1069555953 Owner’s Manual

...

....,] / .....

"" SEARS

.....Kenmore

Refrigerator Safety

Your safety is important to us.

This guide contains safety statements under warning symbols. Please pay special attention to these sym-

bols and follow any instructions given. Here is a brief explanation of the use of the warning symbol.

This symbol alerts you to hazards such

as fire, electrical shock, or other injuries.

IMPORTANT SAFETY INSTRUCTIONS

• Read all instructions before using the refrigerator. =, Child entrapment and suffocation are not

problems of the past. Junked or abandoned refrigerators are still dangerous ... even if they

will "just sit in the garage a few days."

if you are getting rid of your old refrigerator, do

it safely. Please read the enclosed safety booklet

from the Association of Home Appliance Manufac- turers. Help prevent accidents.

- SAVE THESE INSTRUCTIONS -

• Never allow children to operate, play with, or crawl

inside the refrigerator.

• Never clean refrigerator parts with flammable fluids. The fumes can create a fire hazard or explosion_

• FOR YOUR SAFETY •

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE

VICINITY OF THIS OR ANY OTHER APPLIANCE. THE FUMES CAN CREATE A FIRE HAZARD OR

EXPLOSION.

Help us help you

Write down the following information about your

refrigerator to better help you obtain assistance or service if you ever need it. You will need to know your

complete model and serial number. You can find this information on the model and serial number label.

Dealer name Address

Phone number Model number

Serial number

Purchase date (See "Parts and Features" on page 2 for model and serial number label location.)

Keep this book and your sales slip together for future reference.

Parts and Features

This section contains illustrations of your refrigerator. Use them to become familiar with the location of all the parts and features. Page references are included for your convenience.

Li Slide-out Control panel Light switch Refrigerator light (p. 20) (p. 15) (p. 8) (p. 19) Modelnumberandseriallabel

Automatic (on side wall)

ice (p. 1)

(p. 1O) z___

Ice

:(p. 18)

compartment

Dairy

Door

(p. 14)

Light

(p. 20)

Adjustable shelves

(p. t5)

(p. 15)

Freezer baskets

(p. 17) dity

Leveling rollers

(behind base grille) grille Meat drawer Meat drawer (p. 4) (p. 23) air control (p. 15)

(on side wall) (p. 13) Meat drawer

(on some models)

Crisper drawer

Egg bin

Dell drawer

(p. 17)

Door bins

(p. 15)

Crisper light

(p. 19)

Slide-out

crisper cover

(p. 16)

control

(p. 14)

-- cover (p. 15)

NOTE: This manual covers several different models, The model you have purchased may have all or some of the parts and features shown here, and they may not match the illustration exactly.

Installing Your Refrigerator

It is important to prepare your refrigerator for use. This section tells you how to clean it, connect it to a power

source, install it, and level it.

Unpacking your refrigerator

Removing packaging materials

Remove tape and any labels from your refrigerator before using (except permanent instruction labels

and the model and serial number label). To remove any remaining tape or glue, rub the

area briskly with your thumb. Do not use sharp

instruments, rubbing alcohol, flammable fluids, or

abrasive cleaners. These products can damage the

surface of your refrigerator. For more information, see "Important Safety Instructions" on page 1.

Electrical requirements

Fire Hazard

Do not use an extension cord. Doing so can result in death, fire, or

electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded electrical supply is required. It is recom-

mended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension

cord. Refer to the Electrical Requirements and Grounding Instructions Sheet in your Literature

Package for more details.

Cleaning before use

After you remove all of the packaging materials,

clean your refrigerator before using it if

needed. See the cleaning instructions on page 22 for more information.

Electrical Shock Hazard

Plug into a grounded three prong outlet. Do not remove ground prong.

Do not use an adapter. Failure to follow these instructions can

result in death, fire, or electrical shock.

3-prong grounding ._ type wall receptacle _

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn the

Thermostat to OFF and then disconnect the

refrigerator from the electrical source. When you are finished connect the refrigerator to the

electrical source and reset the Thermostat to the desired setting.

Refrigerator

power cord ----_ !

I I 3-prong p_lug _ L._ grounding

Space requirements

To ensure proper ventilation for your refrigerator, allow for a 1/2-inch(1.25 cm) space on each side and at the top. For models that have ice and water

dispensers, make sure you leave some extra space at the back to allow for the water line connections.

NOTE: Do not install the refrigerator near an oven, radiator, or other heat source, nor in a location

where the temperature will fall below 55°F (13°C).

,11,

i / r-_

1/2-inch /

minimum at <,,. top and sides "_

Leveling and door alignment

If the refrigerator is not leveled during installation, the doors may be misaligned and not close or seal

properly, causing cooling, frost, or moisture problems. It is very important for the refrigerator to be level in order to function properly.

Move the refrigerator into its final position. Use a level on top of the refrigerator to check that it is level from side-to-side and front-to-back. If the

refrigerator is not level or the doors are uneven, level the refrigerator using the instructions below.

NOTE: If your refrigerator has an automatic ice maker, level it before attaching the ice maker to a

water supply. If you move the refrigerator after the water line has been hooked up you may loosen or disconnect the fittings.

1. Roll out the refrigerator and use a level to check the floor at the back from side-to-side. Use

shims as needed to bring the floor near the wall to level if it is uneven. Roll the refrigerator back

into place with the rear rollers on top of any

shim(s) used so that the rear of the refrigerator is bevel.

2. With the rear already level and the refrigerator in place, use the front leveling screws to level the

refrigerator from side-to-side and front-to-back. Open the refrigerator door and remove the base grille to find the two leveling screws. They are

part of the Front Roller assemblies which are found at the base of the refrigerator on either side.

Right to raise; left to lower

Use a screw- driver to adjust

Front Roller

Leveling screw

NOTE: The leveling screw on the freezer side raises or lowers the freezer door. The leveling screw on the refrigerator side raises or lowers the refrigerator door.

Leveling and door alignment (cont.)

3. To level your refrigerator, you may either turn

the screw clockwise to raise the lower door or turn the screw counterclockwise to lower the

higher door. Place a level on top of the refrig- erator to check adjustments. Use a screw driver

to adjust the leveling screw. (See diagram.)

NOTE: Having someone push against the top of

the refrigerator takes some weight off the

leveling screws and rollers. This makes it easier

to adjust the screws.

4. Open and close doors after each adjustment. Make sure the doors are even. If not, repeat

steps 3 and 4.

5. Reinstall the base grille.

Attaching the ice maker to a water supply

Read all directions carefully before you begin.

Valve selection

Your appliance dealer has a kit available with a

1/4-inchsaddle type shut-off valve, a union, and

copper tubing. Before purchasing, make sure a saddle type valve complies with your local plumb-

ing codes. Do not use a piercing type or ¾8-inch

saddle valve which reduces water flow and clogs more easily.

Electrical Shock Hazard

Unplug the refrigerator before installing ice maker.

Failure to do so can result in death or electrical shock.

INSTALLATION REQUIREMENTS:

• All installations must be in accordance with local plumbing code requirements.

• Use copper tubing only and check for leaks.

• Install ice maker tubing in areas where

temperatures are above freezing.

• It may take up to 24 hours for your ice maker to begin producing ice.

• If operating the refrigerator before installing the water connection, turn ice maker to the OFF

position to prevent operation without water.

Tools needed:

• Standard screwdriver

• 7,46-inchand 1/2-inch#pen-end wrenches or two adjustable wrenShes

• 1/4-inch nut driver

• 1/4-inch drill bit

• Hand drill or electric drill (properly grounded)

Cold water supply

The ice maker water valve contains a flow washer which is used as a water pressure regulator. The

ice maker needs to be connected to a cold water line with water pressure limitations of 20-120 psi.

If a problem occurs, call your utility company or a licensed plumber.

INSTALLATION IS NOT WARRANTED

BY REFRIGERATOR OR ICE MAKER

MANUFACTURER.

Attaching the ice maker to a water supply (cont.)

Connecting to water line

1. Find a 1/?-inch to 11/4-inch vertical COLD water pipe near the refrigerator.

NOTE: Horizontal pipe will work, but the follow-

ing precaution must be taken: Drill on the top

side of the pipe, not the bottom. This will help

keep water away from the drill. This also keeps

normal sediment from collecting in the valve.

2. Measure from connection on rear of refrigerator

to water pipe. Add 7 feet (2.1 m) to allow for moving refrigerator for cleaning. This is the length of 1/4-inchO.D. copper tubing you will

need for the job (length from connection to water pipe PLUS 7 feet [2.1 m]). Be sure both ends of copper tubing are cut square.

3. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

4. Using a grounded drill, drill a 1/4-inch hole on the cold water pipe you have selected.

5. Fasten shut-off valve to cold water pipe with pipe clamp. Be sure outlet end is solidly in the ¼-inch

drilled hole in the water pipe and that washer is under the pipe clamp. Tighten packing nut.

Tighten the pipe clamp screws carefully and

evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing, especially if soft (coiled) copper tubing is used. Now you are ready to connect the copper tubing.

6. Slip compression sleeve and compression nut on copper tubing as shown in diagram. Insert end of

tubing into outlet end squarely as far as it will go.

Screw compression nut onto outlet end with adjustable wrench. Do not overtighten. Turn ON

main water supply and flush out tubing until

water is clear. Turn OFF shut-off valve on the water pipe, Coil copper tubing.

Vertical cold water pipe

Washer

Packing nut

Water shut-off

valve*

Compression Compression sleeve nut

TO REFRIGERATOR --)

* Controls water supply

1/4-inch O,D,

copper tubing

(length from

inleton rear

of refrigerator

to water pipe

plus 7 feet

[2,1 m])

Attaching the ice maker to a water supply (cont.)

Connecting to refrigerator

1. Disconnect the tube clamp on the back of the

product and insert copper tubing through the clamp as shown at the right. Attach the copper

tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Reattach the tube

clamp and tube to the back of the cabinet. Move to step 2.

2. Turn shut-off valve ON. CHECK FOR LEAKS. TIGHTEN ANY CONNECTIONS (INCLUDING

CONNECTIONS AT THE VALVE) OR NUTS THAT LEAK.

3. The ice maker is equipped with a built-in water

screen. However, for long lasting operation, it is recommended that a filter be installed between

the shut-off valve and the refrigerator. (You can order filter part number 4378411 using the toll-

free number on the back of this manual.)

4. After completing installation, connect the refrigerator to the electrical supply and push it

back into place.

5. Check again to make sure the refrigerator is

level. (See "Leveling and door alignment" on page 4.)

CCCZCD

C:ZZZZC3

CCZCZD CCZZZD

CZCCZD

CZZCD CCCCC)

CZZC:Z) CCCZZD CCCZD CZZZZZ3

CCCC_

copper tubing

nut and sleeve

Use only

1/4-inch

from cold

water line

Tube clamp

1/4-inch com-

pression

Using Your Refrigerator

To obtain the best possible results from your refrigerator, it is important that you operate it properly. This section tells you how to set the controls, remove and adjust the features in your refrigerator, and how to save energy.

Setting the controls

When you first install your refrigerator, set the Thermostat Control at -i- and the Air Balance

Control at -i-. Give your refrigerator time to cool down completely before adding food. It is best to

wait 24 hours before adding food.

How the controls work

There are two controls in your refrigerator

compartment. Knowing how each works will help you set the controls properly for your own house-

hold conditions.

The Thermostat Control adjusts both the refrig-

THERMOSTAT

will not cool when the Thermostat Control is set to OFF.

erator and freezer compartment tem-

peratures. Settings

1-3 make the overall

temperature in both compartments warmer.

Settings 4-6 make the overall temperature in

both compartments colder.

NOTE: Your product

IMPORTANT: If you add food before the refrigerator has cooled completely, your food may spoil. Turning

the Thermostat and Air Balance Controls to a higher than recommended setting will not cool the com-

partments any faster.

The Air Balance Control divides the amount of

AIR BALANCE

cold air entering both compartments. Settings

1 and 2 direct more cold

air into the refrigerator compartment. Settings 3

and 4 direct more cold

air into the freezer compartment.

Hold your hand in front of the top vent (see the diagram "Ensuring proper air circulation" on page 9) and adjust the Air Balance Control to feel the difference in air flow. As you adjust the Air

Balance Control to a lower setting, you will feel more cold air entering the Refrigerator compart-

ment. If you make changes to the control settings, it is best to move the control knob in 1/2step

increments and wait 24 hours in between adjust- ments. This will help prevent you from making your refrigerator warmer or colder than needed.

For further information about air circulation or

temperature, refer to the Troubleshooting

Guide on pages 28-34.

.....i..........................................................................................

Ensuring proper air circulation

In order to ensure proper temperatures, you need to permit air flow between the two compartments. As shown in the illustration, cold air enters the

bottom of the freezer section (A) and moves up.

It then enters the fresh food section through the

top vent (B). Air returns to the freezer through the vent at (C).

Do not block any of these vents with food such as soda, cereal, bread, etc. If the vents

are blocked, air flow will be prevented and the temperature controls will not function properly.

To adjust the air control vent D, see "Adjusting the

Meat Drawer Temperature" on page 13. This

vent directs cold air into the meat drawer so that

it is colder than the rest of the refrigerator com-

partment. NOTE: Because air circulates between both

sections, any odors formed in one section will transfer to the other. You must thoroughly clean

both sections to eliminate odors. To prevent odor transfer from food, wrap or cover foods tightly.

For further information about air circulation or

temperature, refer to the Troubleshooting Guide on pages 28-34.

Using the automatic ice maker

Before you turn the ice maker on, be sure that it is attached to a water supply. Instructions for the ice

maker water supply hookup are on pages 5-7 of this manual.

• The ON/OFF lever is a wire signal arm. Push the arm down to start making ice automatically, and push it up to shut off the ice maker.

• It is normal for the ice to be attached at the corners. It will break apart easily.

• The ice maker will not operate until the freezer is

cold enough to make ice. This can take as long as 24 hours.

REMEMBER:

• The quality of your ice will be only as good as the quality of the water supply that the ice maker is

hooked up to.

• Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as

salt) can damage the ice maker mold and lead to poor quality ice. If a softened water supply

cannot be avoided, make sure the water softener is operating properly and is well maintained.

Signal arm

Ejector arm

Off

Using the ice and water dispensers

Cut Hazard

Use a sturdy glass when dispensing ice or water.

Failure to do so can result in cuts.

Your refrigerator has come equipped with ice and water dispensers. Your model may or may not

have the option of choosing cubed or crushed ice. Some models feature cubed ice only.

The ice dispenser

The ice dispenses from the ice maker storage bin located in the freezer. When you press the dis-

penser bar, a trapdoor opens in a chute between the dispenser and the ice bin. The ice moves from

the bin and falls through the chute. When you release the dispenser bar, a buzzing sound may be

heard for a few seconds as the trapdoor closes.

For crushed ice, cubes are crushed before being dispensed. This may cause a slight delay when dispensing crushed ice. Noise from the ice crusher

is normal, and pieces of ice may vary in size.

CUBEDICE CRUSHED

"1 I

When changing from CRUSHED to CUBED, a few ounces of crushed ice will be dispensed along with

the first cubes.

CUBEDICE CRUSHED

I I

Using the ice and water dispensers (cont.)

The ice dispenser (cont.)

To dispense ice:

• Select CUBED or CRUSHED (if available) by

moving the Ice Selector Switch to the desired setting.

• Press a sturdy glass against the ice dispenser bar. Be sure to hold the glass close to the

dispenser opening so ice does not fall outside of the glass.

• Remove the glass to stop dispensing.

• If you need a large amount of ice, take it directly from the ice bin in the freezer. Do not use the

dispenser. (See "The dispenser arm has been held in too long" on page 31.)

NOTE: The dispenser will not operate when the

freezer door is open. The first few batches of ice

have an off-flavor due to the new plumbing and parts. Throw this ice away.

CUBEDIC_ CRUSHEO

I--t

The water dispenser

The water for the dispenser comes from a tank

behind the meat drawer. It holds approximately 11/2quarts (1.5 L). Dispense enough water every

week to maintain a fresh water supply in the tank.

To start the water dispenser when the refrigerator

is first hooked up, press the water dispenser bar

with a glass or jar until you draw and discard two or three quarts (1.9 to 2.8 L). It will take one to three

minutes for water to begin dispensing. This first

water that you draw and discard will fill the tank and

pipes. Allow several hours to cool a new tankful.

To dispense water, press a sturdy glass against the water dispenser bar. Remove the glass to stop

dispensing.

NOTE: The small tray beneath the dispenser is designed to evaporate small drips. Do not pour water into the tray because there is no drain in it.

Using the

ice and water dispensers (cont.)

The dispenser light

To turn on the night light, slide dispenser LIGHT

switch to the left.

On models without crushed ice, the light switch

isa vertical plunger type. Push up on the switch to

turn the light on, and push up again to turn the

light off.

See page 20 for directions on changing the

dispenser light bulb.

LIGHT ON OFF

Adjusting the meat drawer temperature

The meat drawer is cooled from cold air that flows

in from the freezer

compartment through a vent in the wall of

the refrigerator (See

"Ensuring proper air

circulation" vent D on

page 9.) This helps to keep the meat drawer

colder than the rest of the refrigerator for

better storage of meats.

To adjust the temperature, slide the control from side to side to let more or less cold air into the meat

drawer. Set the control toward Cold for a slightly cooler temperature, or toward Colder for a much

cooler temperature.

NOTE: Putting the control on the coldest setting

may cause freezing or ice crystals, depending on the items you have in the meat drawer.

Adjusting the crisper humidity control

You can control the amount

Humidity Controlled Crisper

_e., o • o,Low

of humidity in the

moisture-sealed crisp-

ers. Adjust the control to any setting between

LOW and HIGH.

* LOW (open) lets moist

air out of the crisper for best storage of fruits and

vegetables with skins.

• HIGH (closed) keeps moist air in the crisper

for best storage of fresh, leafy vegetables.

Removing the door shelf fronts (on some models)

The door shelf fronts may be removed for easier

cleaning. To remove the shelf front, first

remove all items from the shelf. Then push in

slightly and pull out on each inside tab and lift

the shelf front straight out.

To replace the shelf front line up the ends of

the shelf front with the buttons on the sides of

the door liner. Push the shelf front straight back

until it snaps into place.

Removing the door trim (dispenser area) (on some models)

The trim above the dispenser area may be easily

removed for convenient cleaning. To remove

the trim piece, first remove all items from

the Shelf. Then simply pull straight up on each

end of the trim piece.

To replace the trim, line up each end of the trim

above the trim pocket opening in the door liner wall. Then push the trim

straight down on both sides until it stops.

Adjusting the door bins

The door bins are removable for easy cleaning and

adjusting. To remove

the bin, simply lift the

bin up and pull straight out. To replace the

bin, slide it in above the desired support button

and push down until

"'---_ it stops.

Adjusting the refrigerator shelves

The shelves in your refrigerator are adjustable to match the way you use them. Glass shelves are

strong enough to hold bottles, milk, and other heavy food items.

To remove a shelf, first remove all items from the shelf. Then tilt up the front of the shelf and lift it at the back. Pull the shelf straight out.

To replace a shelf, guide the rear shelf hooks into the slots of the shelf supports on the back liner of

the refrigerator. Tilt the front of the shelf up until the rear hooks drop into the slots and then lower

the front of the shelf into position. NOTE: On some models, certain shelves may slide

out to provide an easier reach to items at the back.

Removing the meat drawer and cover

To remove the meat drawer:

• Slide the meat drawer straight out to the stop.

• Lift the front slightly and slide it out the rest of

the way.

• Replace in the reverse order.

To remove the cover:

• Remove the meat drawer and the crisper.

• Lift the front of the cover off of the supports and remove it by pulling up and out.

To replace the cover:

• Fit the back of the cover into the notch supports on the walls of the refrigerator and

lower it into place.

• Replace the meat drawer and crisper.

Removing the crisper and crisper cover

The crisper and its cover are designed for easy

removal and cleaning. To remove the crisper, slide it straight out to the

stop and lift the front. Then slide it out the rest of the way.

Replace the crisper in the reverse order.

To remove the cover, hold it firmly with both hands, lift the front out of the supports and pull it

up and out. To replace the cover, fit the back of the cover into

the notch supports on the walls of the refrigerator and lower the front into place.

Removing the crisper cover extension

In order to prevent food items from falling behind your crisper, some models have a crisper cover extension that covers the gap between the back wall and the back side of the crisper. You may

want to remove the extension when cleaning. To remove the crisper cover extension, simply

lift up on the front of the extension and pull it off of the supports.

To reinstall the crisper cover extension, fit it back onto the supports on the side walls and rest the front on the crisper cover.

Removing the deli drawer

The deli drawer provides a convenient place to

store raisins, nuts, spreads, and other small items at normal refrigerator temperatures.

To remove the deli drawer, slide the deli drawer straight out to the stop, lift the front, and slide the

drawer out the rest of the way.

Replace the deli drawer in the reverse order.

Pull out to the

stop, lift the front,

and pull again

Removing the freezer basket (plastic bin on some models)

The freezer basket can be used to store bags of frozen fruits and vegetables that can slide off freezer shelves.

For easy removal of the freezer basket, slide it out

to the stop, lift the front, and slide it out the rest of the way.

To replace the basket, position it on the slides,

making sure that the wire stops clear the front of the slides, and

slide it in all the way.

Removing the freezer shelf

The freezer shelf is removable for easy cleaning, or to create more open space in the freezer compart-

ment for storage of large or bulk items.

To remove the shelf, lift the shelf off of the sup-

__ orts and slide out of

Removing the ice maker storage bin

3. Lift up the front of the storage bin and pull it out.There are several reasons why you may need to re-

move, empty, and clean the ice maker storage bin.

• The ice dispenser has not, or will not, be used for a week or more.

• A power failure causes the ice in the bin to melt

and freeze together.

• The ice dispenser is not used regularly.

• Ice tastes off-flavored. (See Troubleshooting guide

on page 33.)

If any of these conditions apply to you, follow the instructions on removing the ice bin.

To remove the ice bin:

1. Pull the covering panel out from the bottom and then slide it back

toward the rear.

4. Empty the ice bin. Use warm water to melt the ice if necessary. Never use anything sharp to break

up the ice in the bin. This can cause damage to the bin and the dispenser mechanism.

5. Wash with a mild detergent and rinse well. Do not use harsh or abrasive cleaners or solvents.

the shelf support holes. Replace in the reverse

_li order.

2. Lift the signal arm so it clicks into the OFF (up) dispensed, but no more

i position. Ice can still be

can be made.

When you replace the bin, make sure it is pushed

in all the way or the dispenser will not work. Then push the signal arm down to the ON position to

restart ice production. Make sure the door is closed tightly.

Changing the light bulbs

Electrical Shock Hazard

Unplug the refrigerator before removing a

light bulb.

Failure to do so can result in death or

electrical shock.

Your refrigerator has several light bulbs. This sec- tion shows you where they are located and tells you

how to change them if they burn out. Before you change any light bulb in your refrigerator, be sure to

turn the Thermostat Control to OFF and unplug the

refrigerator. After you have replaced the bulb, plug the refrigerator in and reset the Thermostat Control

to the desired setting.

NOTE; Not all commercial appliance bulbs will fit

your refrigerator. Be sure to replace the bulb with

one of the same size and shape.

Refrigerator light

1. Reach behind the Control Panel and remove the bulb.

2. Replace the bulb with a 40-watt appliance bulb.

Crisper light

(on some models)

1. Pull the top of the light shield forward until

it snaps free and lower until the light bulb is visible.

2. Replace the bulb with a 40-watt appliance bulb.

3. Pull the top of the light shield up over the bulb

and snap it onto the side wall supports.

NOTE: To remove light shield for cleaning, remove

the crisper and the crisper cover. Then release the

bottom of the shield from the lower side wall supports. Pull the light shield out and wash it with warm water and a liquid detergent. Dry the cover

and replace it in the reverse order.

_ __erator light

_-__ Crisper light

Changing the light bulbs (cont.)

Light below the ice bin

1. Push in the sides of the light shield and pull down until the shield snaps free,

2. Replace the bulb with a 40-watt appliance bulb.

3. Replace the light shield.

Upper freezer light

(on some models)

1. Remove the light shield by grasping the top

center of the shield and pulling forward while

turning it slightly to one side.

2. Replace the bulb with a 40-watt appliance bulb.

3. To replace the light shield:

• Grasp the top center of the shield and insert

the tabs on one end into the slotted holes in the freezer liner.

• Carefully bend the shield at the center to insert the tabs on the other end.

Lower

freezer

light

I I

Upper freezer light

Dispenser area light

1. Reach through the dispenser area to remove the bulb.

2. Replace the bulb with a heavy-duty lO-watt bulb, which can be purchased from your

Kenmore dealer.

__enser

light

Understanding the sounds you may hear

Your new refrigerator may make sounds that your old one didn't make. Because the sounds are new

t6 you, you might be concerned about them. Most

of the new sounds are normal due to new product designs. Hard surfaces, like the floor, walls, and cabinets can make the sounds seem louder than

they actually are. The following describes the kinds of sounds that you might hear, and what may be

U ,

making them.

• Your refrigerator is designed to run more effi- ciently to keep your food items at the desired

temperature. The high efficiency compressor may cause your new refrigerator to run longer

than your old one, and you may hear a pulsating

_orhigh pitched sound.

• Water dripping on the defrost heater during a

defrost cycle may cause a sizzling sound.

Saving energy

There are ways that you can help your refrigerator • run more efficiently.

• Check the door gaskets for a tight seal. Leveling the cabinet will ensure a proper seal.

• Clean the condenser coils regularly. A coil cleaning brush is available for purchase. •

• Open the door as few times as possible.

• ,iDon't block the air vents in the freezer and

refrigerator so that cold air cannot flow freely. (See page 9.)

• If your product is equipped with an ice maker, you will hear a buzzing sound when the water valve opens to fill the ice maker for each cycle.

• You may hear the evaporator fan motor circulat-

ing the air through the refrigerator and freezer compartments.

• When the compressor stops, you may hear a

gurgling sound due to the refrigerant equalizing in your refr!gerator.

• The defrost timer will click when the automatic

defrost cycle begins and ends.

• The Thermostat Control, will click when cycling on and off.

• Rattling noises may come from the flow of

refrigerant, the waterline, or items stored on top of the refrigerator.

• Contraction and expansion of the inside walls

may cause a popping noise.

Do not set your refrigerator and freezer at a colder setting than is needed. Keep the Thermostat

Control at the lowest number setting that keeps

your ice cream firm and your drinks as cold as you like.

Do not put your refrigerator next to a heat source,

such as a range, water heater, furnace, radiator, or

in direct sunlight.

Caring for Your Refrigerator

Your refrigerator is built to give you many years of dependable service. However, there are a few things you can do to help extend its product life. This section tells you how to clean your refrigerator and what to do when going

on vacation, moving, or during a power outage.

Cleaning your refrigerator

Both the refrigerator and freezer sections defrost

automatically. However, clean both about once a month to help prevent

odors from building up. Wipe up spills right away.

To clean your refrigerator, turn the Thermostat Control to OFF, unplug it, take out all removable parts and food, and clean the refrigera-

tor according to the following directions. Be sure to use a sponge or cloth with mild detergent and warm water for cleaning your refrigerator.

Do not touch refrigeration tubes near defrost pan.

Doing so can result in burns.

Burn Hazard

PART HOW TO CLEAN Removable parts " Hand wash, rinse, and dry thoroughly.

(shelves, crisper, etc.)

Outside

Inside walls (allow freezer to warm up so cloth won't stick)

Door liners

and gaskets

Plastic parts

(covers and panels)

Defrost pan

Condenser coils

Wash outside of cabinet. Do not use abrasive or harsh cleaners.

• Wipe thoroughly.

• Wax painted, metal surfaces at least twice a year. Apply a good appliance or auto paste wax with a clean, soft cloth. Waxing exterior

painted, metal surfaces helps provide rust protection. Do not get

wax on plastic parts or gaskets.

• Wash with mixture of warm water and:

- mild detergent, or

- baking soda (2 tbs to I qt [about 25 g to 1L] of water).

• Wipe thoroughly.

• Wash and wipe thoroughly.

DO NOT USE cleaning waxes, concentrated detergents, bleaches, or cleaners containing petroleum on plastic parts or gaskets.

• Wash and wipe thoroughly.

DO NOT USE paper towels, window sprays, scouring cleansers, or

flammable fluids. These can scratch or damage plastic parts. See "Important Safety Instructions" on page 1.

• Remove base grille. (See page 23.)

• Reach into small opening at left edge and remove the defrost pan.

• Wash, rinse, and dry thoroughly.

• Replace defrost pan. Make sure to push it completely into the opening.

• Replace base grille.

• Remove base grille.

• Vacuum coils when dusty or dirty. Coils may need to be cleaned as often as every other month.

• Replace base grille.

Removing the base grille

You will need to remove the base grille to clean the

defrost pan or the condenser coils (see above), or to level the refrigerator.

To remove the base grille:

1. Open both doors.

2. Place hands along the ends of the grille, with your thumbs along the top. Push in with your

thumbs and pull up on the bottom.

NOTE: Be sure to replace the Tech Sheet that is

fastened behind the grille if it has been removed for cleaning.

To replace the grille:

1. Line up the grille support tabs with the metal clips.

2. Push the grille firmly to snap it into place and close the doors.

Removing Doors

Metal clips

Defrost pan

Support tabs

Condenser coils

Base grille

Electrical Shock Hazard

Unplug the refrigerator from electrical

supply before removing doors. Failure to do so can result in death or

electrical shock.

NOTE: Before removing doors, open both doors

and remove base grille (see above).

TOOLS NEEDED:

Phillips screwdriver, 1/4"hex-head socket wrench,

%6" hex-head socket wrench.

1, If you have a dispenser (ice or water), discon-

nect water line.

• Remove hose from clip (A).

• Disconnect union nut (B) and slide it back onto tube.

• Remove metal insert (C) from tube.

• Remove union nut (B) and spring (D).

2 j

Removing Doors (cont.)

2. Left top hinge

• Remove hinge cover (A) and screws (B).

• Disconnect wiring plug (D) and both ground wires (C).

Carefully lift door up off bottom hinge. Make sure you protect water line from damage.

DO NOT REMOVE SCREW (E) [not on all models]

3. Disassemble right top hinge.

• Pry off hinge cover (A).

• Remove screws (B).

Lift door up off bottom hinge. DO NOT REMOVE SCREW (C)

[not on all models]

4. Bottom hinge, remove if necessary. Similar construction on both bottom hinges, NOTE: It may not be necessary to remove

bottom hinge to move refrigerator through a

doorway.

DO NOT REMOVE SCREW (A) [not on all models]

Vacation and moving care

Short vacations

If you will be away for less than four weeks, there is no need to turn off your refrigerator. Use these tips

to prepare your refrigerator before you leave.

1.' Use up any perishables and freeze other items.

2. Raise ice maker signal arm to the OFF (up) position and shut off the water supply.

3. Empty the ice bin.

Long vacations

If you will be gone for a month or more, follow these steps to prepare your refrigerator.

1.'Turn off the water supply to the ice maker at least

one day ahead of time.

2. When the last load of ice drops, turn off the ice maker and make sure all ice is dispensed out of

the ice maker mechanism.

3. Remove all food from your refrigerator.

4.'Turn the Thermostat Control to OFF.

5. Unplug the refrigerator.

6. Remove water that may be in the defrost pan. (See page 22.)

7. Clean it, wipe it, and dry well.

8.i_To keep the doors propped open far enough for air to get in, tape rubber or wooden blocks to the

tops of both doors. This will stop odor and mold

i from building up.

Moving

When you are moving your refrigerator to a new

home, follow these steps to prepare it for the move.

1. Turn off the water supply to the ice maker at least one day ahead of time.

2. Disconnect the water line from the back of the refrigerator,

3. When the last load of ice drops, lift the signal

arm to the OFF (up) position.

4. Remove all food from the refrigerator and pack

all frozen food in dry ice.

5. Turn the Thermostat Control to OFF.

6. Unplug the refrigerator.

7. Empty water from the defrost pan.

8. Clean, wipe, and dry the entire product well.

9. Take out all removable parts, wrap them well, and tape them together so they don't shift and rattle during the move.

10. Screw in the leveling rollers.

11. Tape the doors shut and the power cord to the refrigerator cabi net.

When you get to your new home, put everything back and see page 3 for installation instructions.

Also, if your refrigerator has an automatic ice maker, remember to reconnect the home water

source to the refrigerator.

Power interruptions

If the electricity in your house goes off, call the power company and ask how long it will be off.

1. If the power will be out for 24 hours or less, .ikeep both doors closed to help foods stay

cold and frozen.

2. If the power will be out for more than 24 hours: (a) Remove all frozen food and store it in a

frozen food locker.

(b) Place 2 lb. (900 g) of dry ice in the freezer

for every cubic foot (liter) of freezer space. This

will keep the food frozen for two to four days.

While handling dry ice, wear gloves to protect

your hands from ice burns.

IMPORTANT: A full freezer stays cold longer than a partly filled one. A freezer full of meat stays cold longer than a freezer full of baked goods. If food

contains ice crystals, it may be safely refrozen, although the quality and flavor may be affected. If

the condition of the food is poor, or if you feel it is unsafe, dispose of it.

Food Storage Guide

There is a correct way to package and store refrigerated or frozen food. To keep food fresher, longer, take the time to study these recommended steps.

Storing fresh food

Wrap or store food in the refrigerator in airtight and moisture-proof material unless otherwise noted.

This prevents food odor and taste transfer through- out the refrigerator. For dated products, check code date to ensure freshness.

Leafy vegetables

Remove store wrapping and trim or tear off bruised and discolored areas. Wash in cold water and drain.

Place in plastic bag or plastic container and store in crisper.

Vegetables with skins

(carrots, peppers)

Store in crisper, plastic bags, or plastic container.

Fruit

Wash, let dry, and store in refrigerator in plastic

bags or crisper. Do not wash or hull berries until

they are ready to use. Sort and keep berries in original container in a crisper, or store in a loosely closed paper bag on a refrigerator shelf.

Eggs

Store without washing in original carton on

interior shelf or in the egg bin, if provided with

your model.

Milk

Wipe milk cartons. For best storage, place milk on

interior shelf.

Butter or margarine

Keep opened butter in covered dish or closed

compartment. When storing an extra supply, wrap

in freezer packaging and freeze.

Cheese

Store in the original wrapping until you are ready to

use it. Once opened, rewrap tightly in plastic wrap or

aluminum foil.

Leftovers

Cover leftovers with plastic wrap or aluminum foil.

Plastic containers with tight lids can also be used.

Meat

Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following for storage times. When storing

meat longer than the times given, freeze the meat.

Chicken ............ 1-2 days Bacon .............. 5-7 days

Ground beef ..... 1-2 days Cold cuts ......... 3-5 days

Steaks/roasts ... 3-5 days Variety meats ... 1-2 days Cured meats ._ 7-10 days

Fish

Use fresh fish and shellfish the same day

as purchased.

Storing frozen food

The freezer section is designed for storage of commercially frozen food and for freezing food

at home. NOTE: For further information about preparing

fo6d for freezing or food storage times, check a freezer guide or reliable cookbook.

Packaging

The secret of successful freezing is in the packag-

ing. The way you close and seal the package must not allow air or moisture in or out. Packaging done

in 'any other way could cause food odor and taste

transfer throughout the refrigerator and drying of frozen food.

Packaging recommended for use:

• Rigid plastic containers with tight-fitting lids

• Straight-sided canning/freezing jars

• Heavy-duty aluminum foil

• Plastic-coated paper

• _lon-permeable plastic wraps (made from

saran film)

• Specified freezer self-sealing plastic bags

Follow package or container instructions for proper freezing methods.

Do not use:

• Bread wrappers

• Non-polyethylene plastic containers

• Containers without tight lids

• Wax paper

• Wax-coated freezer wrap

• Thin, semi-permeable wrap

The use of these wrappings could cause food odor, taste transfer, and drying of frozen food.

Freezing

Do not expect your freezer to quick-freeze any large

quantity of food. Put no more unfrozen food into the freezer than will freeze within 24 hours. Leave enough

space for air to circulate around packages. Be careful to leave enough room at the front so the door can

close tightly.

Storage times will vary according to the quality

and type of the food, the type of packaging or wrap

used, (airtight and moisture-proof), and the storage

temperature.

Ice crystals inside a sealed package are normal.

This simply means that moisture in the food and air inside the package has condensed, creating

ice crystals.

Troubleshooting Guide

You can solve many common refrigerator problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve your problem without outside help.

Your refrigerator will not operate

Check if ,,. The power supply cord is unplugged.

A household fuse has blown or circuit breaker has tripped.

The Thermostat Control is turned to the

"OFF" position.

The refrigerator is defrosting.

Then ..,

Firmly plug the cord into a live outlet with proper voltage.

Replace the fuse or reset the circuit.

See "Setting the controls" on page 8.

Recheck to see if the refrigerator is operating in 30 minutes. Your refrigerator will regularly run an

automatic defrost cycle. If it is still not running after checking the above

items, call for service.

The lights do not work

Check if ... Then ...

The power supply cord is unplugged. Firmly plug the cord into a live outlet with

proper voltage.

A household fuse or circuit breaker has tripped. Replace the fuse or reset the circuit, A light bulb is loose in the socket. Turn the Thermostat Control to OFF.

Disconnect the refrigerator from the electrical supply. Gently remove the bulb and reinsert. Then reconnect

the refrigerator to the electrical supply and reset the Thermostat Control.

A light bulb has burned out. Replace with an appliance bulb of the same wattage,

size, and shape. See "Changing the light bulbs" on page 19.

Ice crystals in the meat drawer

Check if ... Then ...

The meat drawer temperature control is set to the Set the meat drawer temperature control to a lower

highest setting, setting.

There is water in the defrost drain pan

Check if ... Then ... The refrigerator is defrosting. The water will evaporate. It is normal for water to drip

into the defrost pan.

It is more humid than normal. Expect that the water in the defrost pan will take longer

to evaporate. This is normal when it is hot or hur_id.

Water in the defrost pan is overflowing. Check to make sure your refrigerator is level. (See

"Leveling and door alignment" on page 4.) If it is still

overflowing there is probably something wrong with the refrigerator. Call for service.

The motor seems to run too much

Check if ... Then ...

The room temperature is hotter than normal. Expect the motor to run longer under warm conditions.

At normal room temperatures, expect your motor to

run about 40% to 80% of the time. Under warmer conditions, expect it to run even more of the time.

A Jarge amount of food has just been added to Adding a large amount of food warms the refrigerator. the refrigerator. It is normal for the motor to run longer in order to

cool the refrigerator back down. See "Food Storage Guide" on page 26.

Tl_e door is opened often. Expect the motor to run longer when this occurs. In

order to conserve energy, try to get everything you need out of the refrigerator at once, keep food orga-

nized so it is easy to find, and close the door as soon as the food is removed.

The controls are not set correctly for the See "Setting the controls" on page'8. surrounding conditions.

The doors are not closed completely. Push the doors firmly shut. If they will not shut alt the

way, see "The doors will not close completely," on page 34.

The doors are misatigned. See "Leveling and door alignment" on page 4 or call

The base grille is dirty or blocked. This prevents air circulation and makes the motor

The condenser coils are dirty. This prevents air transfer and makes the motor work

for service

work harder. Remove the grille and clean. See "Removing the base grille" on page 23.

harder. Clean the condenser coils. See "Cleaning your refrigerator" on page 22.

If the problem is not due to any of the above, remember that your new refrigerator will run longer

than your old one due to its high efficiency motor.

+ 91 hidden pages