Kenmore 10686399310, 10686393310, 10686392310, 10676393410, 10676392410 Owner’s Manual

...

Use & Care Guide Manual de uso y cuidado

Guide d'utilisation et d'entretien

English / Espafiol / Fran_ais

Model/Modelo/Mod_le: 106.8639 _

I<enmore

Mount

= color number_ n@nero de colo_ le num@o de la couleur

P/N W10609153A Sears Brands Management Corporation

Hoffman Estates, IL, U.S.A. 60179 www.kenmore.com www.sears.com

Sears Canada Inc. Toronto, Ontario, Canada M5B 2C3

www.sears.ca

TABLEOF CONTENTS

PROTECTION AGREEMENTS ................................................... 2

WARRANTY ............................................................................. 3

REFRIGERATOR SAFETY......................................................... 4

Proper Disposal of Your Old Refrigerator ....................................5

INSTALLATION INSTRUCTIONS .............................................. 5

Unpack the Refrigerator ..................................................................5

Location Requirements ..................................................................... 7

Electrical Requirements ................................................................... 7

Water Supply Requirements .......................................................... 7

Connect the Water Supply ..............................................................8

Refrigerator Doors .............................................................................9

Leveling and Door Adjustment ......................................................12

Normal Sounds .................................................................................12

REFRIGERATOR USE.............................................................. 12

Ensuring Proper Air Circulation .....................................................12

Using the Controls ........................................................................... 13

Ice Maker ..........................................................................................14

REFRIGERATOR FEATURES.................................................... 14

Refrigerator Shelves ........................................................................14

Meat Drawer ....................................................................................14

Crisper ................................................................................................15

Utility or Egg Bin..............................................................................16

FREEZER FEATURES................................................................ 16

Freezer Shelf .................................................................................... 16

DOOR FEATURES.................................................................... 16

Door Rails or Trivets........................................................................ 16

Can Racks and Door Bins.............................................................. 17

REFRIGERATOR CARE ........................................................... 17

Cleaning ............................................................................................ 17

Changing the Light Bulbs ............................................................... 17

Power Interruptions ......................................................................... 18

Vacation and Moving Care .......................................................... 18

TROUBLESHOOTING .............................................................. 19

Refrigerator Operation .................................................................. 19

Temperature and Moisture ........................................................... 20

Ice and Water ................................................................................ 20

ACCESSORI ES......................................................................... 21

SERVICE NUMBERS ............................................. BACK COVER

JNDICE ................................................................................... 22

TABLE DESMATIERES ............................................................ 43

PROTECTION AGREEMENTS

Master Protection Agreements

Congratulations on making a smart purchase. Your new

Kenmore ® product is designed and manufactured for years of dependable operation. But like all products, it may require preventive maintenance or repair from time to time. That's when

having a Master Protection Agreement can save you money and aggravation.

The Master Protection Agreement also helps extend the life of your new product. Here's what the Agreement* includes:

1/Parts and labor needed to help keep products operating

properly under normal use, not just defects. Our coverage goes well beyond the product warranty. No deductibles, no

functional failure excluded from coverage--real protection.

1/Expert service by a force of more than 10,000 authorized

Sears service technicians, which means someone you can trust will be working on your product.

1/ Unlimited service calls and nationwide service, as often as

you want us, whenever you want us.

1/"No-lemon" guarantee- replacement of your covered

product if four or more product failures occur within twelve months.

1/Product replacement if your covered product can't be fixed. 1/Annual Preventive Maintenance Check at your request - no

extra charge.

I/' Fast help by phone - we call it Rapid Resolution - phone

support from a Sears representative on all products. Think of us as a "talking owner's manual."

1/Power surge protection against electrical damage due to

power fluctuations.

I/$250 Food Loss Protection annually for any food spoilage

that is the result of mechanical failure of any covered refrigerator or freezer.

I/Rental reimbursement if repair of your covered product takes

longer than promised.

1/10% discount off the regular price of any non-covered repair

service and related installed parts.

Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime

day or night, or schedule a service appointment online. The Master Protection Agreement is a risk free purchase. If you

cancel for any reason during the product warranty period, we will provide a full refund. Or, a prorated refund anytime after

the product warranty period expires. Purchase your Master Protection Agreement today!

Some limitations and exclusions apply. For prices and additional information in the U.S.A. call 1-800-827-6655.

*Coverage in Canada varies on some items. For full details call

Sears Canada at 1-800-361-6665.

Sears Installation Service

For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in the

U.S.A. or Canada call 1-800-4-MY-HOME ®.

KENMORE APPLIANCE WARRANTY

ONE YEAR LIMITED WARRANTY

When installed, operated and maintained according to all supplied instructions, if this appliance fails due to a defect in

material and workmanship within one year from the date of purchase, call 1-800-4-MY-HOME _ (1-800-469-4663) to

arrange for free repair. If this appliance is ever used for other than private family

purposes, this warranty applies for only 90 days from the date of purchase.

Thiswarranty covers only defects in material and workmanship. Sears will NOT pay for.

1. Expendable items that can wear out from normal use,

including but not limited to filters, belts, incandescent light bulbs, and bags.

2. A service technician to instruct the user in correct product installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed, operated or maintained according to all instructions

supplied with the product.

5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product caused by the useof detergents, cleaners, chemicals or utensils other than those

recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

Disclaimer of implied warranties; limitation of remedies Customer's sole and exclusive remedy under this limited

warranty shall be product repair as provided herein. Implied warranties, including warranties of merchantability or fitness for

a particular purpose, are limited to one year or the shortest period allowed by law. Sears shall not be liable for incidental or

consequential damages. Some states and provinces do not allow the exclusion or limitation of incidental or consequential

damages, or limitations on the duration of implied warranties of merchantability or fitness, so these exclusions or limitations may

not apply to you. This warranty applies only while this appliance is used in the

United States or Canada _. This warranty gives you specific legal rights, and you may also

have other rights which vary from state to state.

In Canada, in-home repair service is not available in all

areas, nor will this warranty cover user or servicer travel and transportation expenses if this product is located in a remote

area (as defined by Sears Canada Inc.) where an authorized servicer is not available.

Sears Brands Management Corporation

Hoffman Estates, IL 60179

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2C3

PRODUCT RECORD

Record your complete model number, serial number, and purchase date. You can find this information on the model and

serial number label located on the product. Have this information available to help you obtain assistance or

service more quickly whenever you contact Sears concerning your appliance.

Model number

Serial number

Purchase date

Save these instructions and your sales receipt for future reference.

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:To reduce the risk of fire, electric shock, or injury to persons when using the refrigerator, follow basic precautions,

including the following:

[] Plug into a grounded 3 prong outlet. [] Do not remove ground prong. [] Do not use an adapter.

[] Do not use an extension cord. [] Disconnect power before servicing.

[] Replace all parts and panels before operating. [] Remove doors from your old refrigerator.

SAVETNESEINSTRUCTIONS

[] Use nonflammable cleaner. [] Keep flammable materials and vapors, such as gasoline,

away from refrigerator. [] Use two or more people to move and install refrigerator. [] Disconnect power before installing ice maker (on ice maker

kit ready models only).

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

ProperDisposalof YourOld Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.

IMPORTANT= Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are

still dangerous - even if they will sit for "just a few days." If you are getting rid of your old refrigerator, please follow these

instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer..

• Take off the doors.

• Leave the shelves in place so that children may not easily climb inside.

important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

IMPORTANT: Do not remove the white foam air return insert from behind the control panel on the ceiling of the refrigerator.

If the insert is removed, ice may migrate down from the freezer and cause icicles to form.

e H_ _e_"<se

Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Rinse with warm water and dry with a soft cloth.

NOTE= Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or

glue. These products can damage the surface of your refrigerator. For more information see "Refrigerator Safety."

When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.

Install Levelers

IMPORTANT: Lay down the refrigerator ONLY to your left-hand side (as you are looking at the front of the refrigerator), to avoid

damaging the refrigerator.

1. Locate the levelers. They are enclosed in a plastic bag inside the crisper drawer.

Using two or more people, access the bottom of the refrigerator either by tilting it first to one side and then the

other, OR by laying it down on the floor to your left-hand side, as shown.

• Tilt the refrigerator to the side enough to access the

bottom. Using a 3/8"hex driver, remove the two screws attaching the wooden runner to the bottom of the

refrigerator. Then install a leveler to the front corner. Repeat for the opposite side.

NOTE: The refrigerator cabinet should not touch the floor without a leveler installed.

• Using the packaging corner posts (left-hand side, front and back) as a cushion, lay the refrigerator down on the

floor (to your left-hand side only), as shown in the following graphic.

NOTE: Using the packaging as a cushion will help avoid

denting or scratching the refrigerator.

• Using a 3/8" hex driver, remove the two screws attaching each wooden runner to the bottom of the refrigerator.

Install a leveler to each of the front corners.

A B

A. Remove runner.

B. /nsta// /eveler.

C. Packaging corner post

Clean Before Using

A B

A. Remove runner.

B. /nsta// /eve/er.

After you remove all of the package materials, clean the inside of your refrigerator before using it. See the cleaning instructions

in "Refrigerator Care."

important information to know about glass shelves

an_ covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT= This refrigerator is designed for indoor, household use only.

To ensure proper ventilation for your refrigerator, allow 1/2" (1.25 cm) of space on each side, and between the top of the

refrigerator and overhead cabinets. Allow 2" (5 cm) of space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections.

When installing your refrigerator next to a fixed wall, leave a 31/8"(8 cm) minimum space on the hinge side to allow the door

to swing open. NOTE= This refrigerator is intended for use in a location where

the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature

range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C)

and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.

Electrical Shock Hazard

Plug intoa grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not usean extension cord. Failureto follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical

connection. Recommended Grounding Method

A 115volt, 60 Hz, AC only, 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an

extension cord. NOTE= Before performing any type of installation or cleaning, or

removing a light bulb, turn cooling off or turn the control (Thermostat, Refrigerator or Freezer Control depending on the

model) to OFF, and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the

refrigerator to the electrical source and turn cooling on or reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting. See "Using the Controls" in the User Instructions, User Guide, or Use & Care

Guide.

3%" (8 cm)

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

IMPORTANT:

• If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain

above freezing.

TOOLS NEEDED= Flat-blade screwdriver, 7_,, and _/_"open-end wrenches or two adjustable wrenches, %" nut driver and drill bit,

cordless drill.

NOTE:Yourrefrigeratordealerhasakitavailablewitha1/4" (6.35mm)saddle-typeshutoffvalve,aunion,andcopper

tubing.Beforepurchasing,makesureasaddle-typevalve complieswithyourlocalplumbingcodes.Donotuseapiercing-

typeor3A6"(4.76mm)saddlevalvewhichreduceswaterflow andclogsmoreeasily.

Water Pressure

Using a cordless drill, drill a 1/4" hole in the cold water pipe you have selected.

A cold water supply with water pressure of between 30 and 120 psi (207 and 827 kPa) is required to operate ice maker. If

you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and

827 kPa). If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa).

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If you have questions about your water pressure, call a licensed, qualified plumber.

Ce } ' ec }'he ............

A. CoM wotor pipo E. Comprossion sloovo

B. Pipe clomp E Shutoff volvo

C. Copper tubing G. Pecking nut D. Compression nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4"drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so washer makes a watertight seal. Do not overtighten.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not

overtighten.

8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water

is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

NOTE: On kit models, assemble water valve to refrigerator according to kit instructions.

Read all directions before you begin. IMPORTANT: If you turn the refrigerator on before the water

line is connected, turn the ice maker OFF to avoid excessive noise or damage to the water valve.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a 1/2"to 11/4'' (1.27 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

Make sure it is a cold water pipe. Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the

valve.

Determine the length of copper tubing you will need. Measure from the connection on lower left rear of

refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"(6.35 mm) O.D. (outside diameter) copper

tubing. Be sure both ends of copper tubing are cut square.

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the

compression nut. Do not overtighten.

3. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

............ A

A. Tube clomp

B. Tube clomp screw

C. Copper tubing

D. Compression nut

E. Volvo inlet

The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install

it in the 1/4" (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

Style 2

1. Unplug refrigerator or disconnect power.

2. Disconnect the tube clamp on the back of the product and insert the copper tubing through the clamp as shown.

3. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown.

4. Tighten the compression nut. Do not overtighten. Reattach the tube clamp and tube to the back of the cabinet.

TOOLS NEEDED: _t" hex-head socket wrench, #2 Phillips screwdriver, flat-blade screwdriver, s/%,,open-end wrench, flat

2" putty knife. IMPORTANT:

• Before you begin, turn the refrigerator control OFF. Unplug refrigerator or disconnect power.

• Remove food and adjustable door or utility bins from doors.

• If you are only removing and replacing the doors, see the "Remove Doors and Hinges" and "Replace Doors and

Hinges" sections.

A. Tube clamp

B. Copper tubing

Turn shutoff valve ON. Check for leaks. Tighten any

C. Compression nut

connections (including connections at the valve) or nuts that leak.

The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the 1/4" (6.35 mm) water line at either tube connection.

Obtain a water strainer from your nearest appliance dealer.

Complete the Installation

Remove Doors and Hinges

%6 "Hex-Heod Hinge Screw

Unplug refrigerator or disconnect power.

Close the refrigerator door and keep both doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide support between the freezer and refrigerator doors while the hinges are being moved. Do not depend on

the door magnets to hold the doors in place while you are working.

Remove the parts for the top hinge as shown in Top Hinge graphic. Lift the freezer door free from the cabinet.

Remove the parts for the center hinge as shown in the Center Hinge graphic.

NOTE: Provide support between the refrigerator door and the floor while the hinges are being moved. Do not depend

on the door magnets to hold the door in place while you are working.

Lift the refrigerator door free from the cabinet.

Remove the four screws (two on the bottom and two on the front) attaching the Bottom hinge to the cabinet. See Bottom

Hinge graphic.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet. NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely fill ice container.

Reverse Doors (optional)

Final Steps

IMPORTANT: If you want to reverse your doors so that they open in the opposite direction, follow these steps. If you are not

reversing the doors, see "Replace Doors and Hinges." Graphics follow these instructions.

Door Hinge

Hole Plug

Cabinet Hinge

Hole Plug

Cabinet

From the top of the cabinet, remove the hinge hole plugs, move them to the opposite side, and insert the hole plugs

into the holes from where you removed the hinge screws. See Graphic 1-2.

2. Remove the screws filling the holes to be used for the Center Hinge and install them on the opposite side.

3. Move the leveler from the bottom of the refrigerator and install it on the opposite side.

4. Move the parts of the top hinge, center hinge and bottom hinge to the opposite side.

Doors

1. Remove door hinge hole plug from top of freezer door. Move to opposite side as shown. See Graphic 2.

2. Remove the door stop from the bottoms of both the freezer and refrigerator doors and install them on the opposite side. See graphics 3 and 4.

Check all holes to make sure that hole plugs and screws are in place.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

2. Plug into a grounded 3 prong outlet.

3. Reset the controls. See "Using the Control(s)."

4. Return all removable door parts to doors and food to refrigerator.

Replace Doorsand Hinges

NOTES:

Graphic may be reversed if door swing is reversed.

Provide additional support for the doors while the hinges are being reinstalled. Do not depend on the door magnets to

hold the doors in place while you are working.

1. Replace the parts for the bottom hinge as shown. Tighten screws. Replace the refrigerator door.

2. Assemble the parts for the center hinge as shown and tighten all screws. See Center Hinge graphic. Replace the

freezer door.

3. Assemble the parts for the top hinge as shown. See Top Hinge graphic. Do not tighten screws completely.

4. Align the doors so that the bottom of the freezer door is even with the top of the refrigerator door. Tighten all screws.

Top Hinge

A, _/_" Hex-Head Hinge Screws B. Top Hinge C. Spacer

Center Hinge

A. Center Hinge

B. %,_"Hex*Head Hinge Screws

Bottom Hinge

A. Cabinet Hinge Hole Plugs

A, Door H#_ge Hole Plug

Removal of Door Stops

A. Bottom Hh_ge

B. _X,,,"Hex.Head Hinge Screws C. Leveler

A. Door Step

B, Door Slop Screw

Reinstaltation of Door Stops

A.Door Stop B,Door StopScrew

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Your refrigerator has two adjustable levelers, one on each side, at the base of the refrigerator. If your refrigerator seems

unsteady or if you want the doors to close more easily, adjust the level and tilt of the refrigerator.

1. Turn the leveler to the left to raise that side of the refrigerator or to the right to lower that side. It may take

several turns to level the refrigerator. NOTE= Having someone push against the top of the

refrigerator takes some weight off the levelers. This makes it easier to turn the levelers.

2. Once the refrigerator is level from side to side, raise the front levelers so that the refrigerator is tilted slightly (approximately 1/2") downward to the rear. The doors will

close more easily and the freezer door will remain closed whenever you close the refrigerator door.

3. Open both doors again to make sure that they close as easily as you like. If not, tilt the refrigerator slightly more to

the rear by turning both levelers to the right. It may take several more turns.

NOTE= To keep the refrigerator level, make the same adjustment to each side.

Using a level, make sure the refrigerator is still level from side to side. Readjust if necessary.

• Your refrigerator is designed to run more efficiently to keep your food items at the desired temperatures and to minimize

energy usage. The high efficiency compressor and fans may cause your refrigerator to run longer than your old one. You may also hear a pulsating or high-pitched sound from the

compressor or fans adjusting to optimize performance.

• You may hear the evaporator fan motor circulating air through the refrigerator and freezer compartments. The fan

speed may increase as you open the doors or add warm food.

• Rattling noises may come from the flow of refrigerant, the water line, or items stored on top of the refrigerator.

• Water dripping on the defrost heater during a defrost cycle may cause a sizzling sound.

• As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your refrigerator.

• Contraction and expansion of the inside walls may cause a popping noise.

• You may hear air being forced over the condenser by the condenser fan.

You may hear water running into the drain pan during the defrost cycle.

REFRIGERATORUSE

In order to ensure proper temperatures, you need to permit

airflow between the refrigerator and freezer sections. As shown in the illustration, cool air enters through the bottom of the

freezer section and moves up. Most of the air then flows through the freezer section vents and recirculates under the freezer floor.

The rest of the air enters the refrigerator section through the top vent.

NOTE= Depending on your model, the refrigerator may have either a Normal flow or Multiflow air system.

Your new refrigerator may make sounds that your old one didn't make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard surfaces, such as the floor, walls, and cabinets, can make

the sounds seem louder. The following describes the kinds of sounds and what may be making them.

• If your refrigerator is equipped with an ice maker, you will hear a buzzing sound when the water valve opens to fill the ice maker for each cycle.

Do not block any of these vents with food packages. If the vents are blocked, airflow will be restricted and temperature and

moisture problems may occur. IMPORTANT= Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. Toavoid odor

transfer and drying out of food, wrap or cover foods tightly.

Temperature Control

When you plug in the refrigerator for the first time, set the Temperature Control to Recommended Setting (middle dot).

Recommended Setting

"OFF

IMPORTANT.

Turning the Temperature Control to OFF stops cooling in the refrigerator and freezer compartments, but it does not disconnect the refrigerator from the power supply.

The Temperature Control regulates the temperature in both the refrigerator and freezer compartments. Settings to the

left of the Recommended setting make the temperature less cold. Settings to the right of the Recommended setting make

the temperature colder. Wait 24 hours before you put food into your refrigerator. If

you add food before the refrigerator has cooled completely, your food may spoil.

NOTE: Adjusting the Temperature Control to a higher (colder) setting will not cool the compartments any faster.

The recommended setting should be correct for normal household usage. The controls are set correctly when milk or

juice is as cold as you like and when ice cream is firm.

If the temperature is too warm or too cold in the refrigerator

or freezer, before adjusting the controls, first make sure the air vents are not blocked.

When you plug in the refrigerator for the first time, turn the Freezer control to Recommended Setting.

Freezer Control

COLDEST Recommended

COLD

Adjust the Freezer Control

If you want to temporarily increase the cold air flow to a

specific compartment, adjust the control. IMPORTANT: Once the performance is achieved, return the

Freezer control to the Recommended setting to keep the refrigerator operating at optimum efficiency.

CONDITION/REASON: ADJUSTMENT:

Heavy ice use Max Freezer

Hot room temperature Max Freezer - To maintain

ice making production rate

Large quantity of groceries Max Refrigerator - To

quickly chill food and beverages

Crisper Humidity Control (on some models)

You control the amount of humidity in the moisture-sealed crisper. Depending on the produce you are storing, select the

desired Humidity Level. Humidity Level - Low Setting

Adju# the Temperature Control NOTE: Wait at least 24 hours between adjustments and then recheck the temperatures.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm Temperature Control

one setting higher

FREEZERtoo warm/too little ice Temperature Control

one setting higher

REFRIGERATOR too cold Temperature Control

one setting lower

FREEZERtoo cold Temperature Control

one setting lower

Freezer Control

The Freezer control is located on the back wall of the freezer. It regulates the amount of air flowing between the freezer and the

refrigerator compartments.

LOW-- HIGH-- MEDIUM

Humidity Control

LOW (open) lets moist air out of the crisper for best storage of fruits and vegetables with skins.

• Fruit. Wash, let dry and store in refrigerator in plastic bag or crisper. Do not wash or hull berries until they are ready to

use. Sort and keep berries in original container in crisper, or store in a loosely closed paper bag on a refrigerator shelf.

• Vegetables with skins: Place in plastic bag or plastic container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of fresh, leafy vegetables.

Leafy vegetables: Wash in cold water, drain and trim or tear off bruised and discolored areas. Place in plastic bag or plastic

container and store in crisper.

/on some modes _,,_,s_,,c_,_,o_'_'_ ...........,j;,s

Turning the Ice Maker On/Off

NOTE: Do not force the wire shutoff arm up or down.

• To turn the ice maker on, simply lower the wire shutoff arm. NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shutoff arm to the OFF (arm up)

position. To manually turn off the ice maker, lift the wire shutoff arm

to the OFF (arm up) position and listen for the click to make sure the ice maker will not continue to operate.

NOTE =Turn off the ice maker before removing the ice storage bin to serve ice or to clean the bin. This will keep the ice cubes

from dropping out of the ice maker and into the freezer compartment. After replacing the ice storage bin, turn on the ice

maker.

Ice Production Rate

In normal operation, the ice maker should produce approximately 8 to 12 batches of ice in a 24-hour period.

If ice is not being made fast enough, adjust the controls.

• Freezer Control - Turn the control dial to COLDEST.

• Temperature Control - Turnthe control dial gradually toward COLDEST, waiting 24 hours between each increase.

REFRIGERATOR FEATURES

Your model may have some or all of these features.

important information to know about glass shelves

and covers:

The shelves in your refrigerator are adjustable to match your individual storage needs.

Storing similar food items together in your refrigerator and adjusting the shelves to fit different heights of items will make

finding the exact item you want easier. It will also reduce the amount of time the refrigerator door is open, and save energy.

Shelves and Glass Shelves (on some models)

To remove and replace a shelf:

1. Remove items from the shelf.

2. Slide the shelf straight out to the stop.

3. Depending on your model, lift back or front of the shelf past the stop. Slide shelf out the rest of the way.

4. Replace the shelf by sliding the back of the shelf into the track in the wall of the cabinet.

5. Guide the front of the shelf into the shelf track. Be sure to slide the shelf in all the way.

Remember

Allow 24 hours to produce the first batch of ice. Allow 3 days to completely fill the ice storage bin. Discard the first

three batches of ice produced. The quality of your ice will be only as good as the quality of

the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener

chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply

cannot be avoided, make sure the water softener is operating properly and is well maintained.

Do not store anything on top of the ice maker or in the ice storage bin.

(©;'ss<:,m®models)

To remove and replace the meat drawer:

1. Slide meat drawer out to the stop.

2. Lift front of meat drawer with one hand while supporting bottom of drawer with other hand. Slide drawer out the rest

of the way.

3. Replace the drawer by sliding it back in fully past the drawer stop.

MeatDrawer Cover (on some models) Crisper Cover

To remove and replace the meat drawer cover:

Remove the meat drawer..

Push the cover back to release the rear clips from the shelf. Tilt the cover up at the front, and pull it forward.

Replace the meat drawer cover by fitting the notches and clips on the cover over the rear and center crossbars on the

shelf.

Lower cover into place and pull the cover forward to secure the rear clips onto the shelf.

Replace the meat drawer. NOTE: In some models the meat pan moves sideways on the

shelf to allow for flexible positioning.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following

chart for storage times. When storing meat longer than the times given, freeze the meat.

Fresh fish or shellfish .......................... use same day as purchased

Chicken, ground beef, variety meats (liver) ..................... 1-2 days

Cold cuts, steaks/roasts ..................................................... 3-5 days

Cured meats ....................................................................... 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or plastic containers with tight lids.

Style 1 - Plastic Cover

To remove and replace the crisper cover.

1. Remove the crisper(s).

2. Lift the front of the cover to remove the cover support. Then lift the cover up and slide it out.

3. Replace the cover by fitting the cover tabs into lowest cabinet slots and pushing them in. Lower the front retainers

into place.

Insert cover support (with the long tab toward the front) into

the groove on the underside of the cover. NOTE: If the support needs adjustment, turn the base of the

support clockwise to raise or counterclockwise to lower.

Crisper Drawers

To remove and replace the crisper drawer:

1. Slide the crisper drawer straight out to the stop. Lift the front

and slide the drawer out the rest of the way.

2. Replace the drawer by sliding the drawer in fully past the stop.

Style 2 - Glass Cover To remove and replace the crisper cover:

1. Pull the glass straight out.

2. Replace the glass by pushing it straight in.

Lllilby °

= .... ]]i161;!

S/¾

(on soss_ modes)

Depending on your model, you may have a one, two or three piece bin. Eggs may be stored in the egg tray or loose in the bin.

NOTE= Store eggs in a covered container for long-term storage. If your model does not have an egg storage bin, store eggs in

their original container on an interior shelf.

FREEZERFEATURES

Frozen Food Storage Guide

Storage times will vary according to the quality and type of food, the type of packaging or wrap used (should be airtight

and moisture-proof), and the storage temperature. Seal the package or container securely to avoid taste and odor transfer

throughout the product. Ice crystals inside a sealed package are normal. This simply means that moisture in the food and air

inside the package have condensed, creating ice crystals. Put no more unfrozen food into the freezer than will freeze within 24 hours (no more than 2 to 3 Ibs of food per cubic foot

[907 to 1,350 g per L] of freezer space). Leave enough space in the freezer for air to circulate around packages. The freezer door must close tightly.

NOTE: For more information on preparing food for freezing, check a freezer guide or reliable cookbook.

Your model may have some or all of these features.

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

(e_ s®me me@As}

To remove and replace the freezer shelf=

1. Remove items from the shelf.

2. Lift back of shelf over stop and slide shelf straight out.

3. Replace the shelf by sliding the back of the shelf into the tracks on walls of cabinet.

4. Be sure to slide the shelf in all the way.

DOOR FEATURES

Your model may have some or all of these features.

Doo or vets

The door rails or trivets may be removed for easier cleaning.

Snap on Door Rails or Trivets (on some models)

To remove and replace the rails or trivets=

1. Depending on your model, remove the rails or trivets by pushing in slightly on the front of the bracket while pulling out on the inside tab. Repeat these steps for the other end.

2. Replace the rails or trivets by aligning the ends of the brackets with the buttons on the sides of the door liner.

Firmly snap bracket and assembly onto the tabs above the shelf as shown.

Style 1 - Door Rails

Style 2 - Trivets

Drop-inDoorRails(onsomemodels)

To remove and replace the rails:

1. Remove the rails by pulling straight up on each end of the rail.

2. Replace the rails by sliding the shelf rail into the slots on the door and pushing the rail straight down until it stops.

(R;m Rc cks {}oo Bi 'ss

NOTE= Can racks may be purchased as an Accessory for some models.

To remove and replace the racks/bins:

1. Remove the rack/bin by lifting it and pulling it straight out.

2. Replace the rack/bin by sliding it in above the desired support and pushing it down until it stops.

To Clean Your Refrigerator:

NOTE= Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh cleaning materials.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean sponge or soft cloth and a mild detergent in warm

water. Dry thoroughly with a soft cloth. NOTE= To keep your stainless steel refrigerator looking like

new and to remove minor scuffs or marks, it is suggested that you use the manufacturer's approved Stainless Steel

Cleaner and Polish. To order the cleaner, see the "Accessories" section.

IMPORTANT= This cleaner is for stainless steel parts only! Do not allow the Stainless Steel Cleaner and Polish to come

into contact with any plastic parts such as the trim pieces, dispenser covers or door gaskets. If unintentional contact

does occur, clean plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft cloth.

4. Plug in refrigerator or reconnect power.

REFRIGERATORCARE

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to keep odors

from building up. Wipe up spills immediately. IMPORTANT= Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

NOTE= Not all bulbs will fit your refrigerator. Be sure to replace the bulb with an appliance bulb of the same size, shape, and wattage.

1. Unplug refrigerator or disconnect power.

2. Remove the upper shelf to access the light shield.

3. Press the side of the light shield to release it from the catch

and pull the shield away from the light assembly.

4. Remove the light bulb and replace it with a new 25-watt appliance bulb. Replace the light shield.

5. Plug in refrigerator or reconnect power.

Moving

If the power will be out for 24 hours or less, keep the door or doors closed (depending on your model) to help food stay cold

and frozen.

If the power will be out for more than 24 hours, do one of the following:

• Remove all frozen food and store it in a frozen food locker.

Place 2 Ibs (907 g) of dry ice in the freezer for every cubic foot (28 L) of freezer space. This will keep the food frozen for 2 to 4 days.

If neither a food locker nor dry ice is available, consume or

can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled one. A freezer full of meat stays cold longer than a freezer

full of baked goods. If you see that food contains ice crystals, it may be refrozen, although the quality and flavor may be

affected. If the condition of the food is poor, dispose of it.

Vacations

If You Choose to Leave the Refrigerator On While You're Away.. I. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker, and is connected to the household water supply, turn off the water

supply to the refrigerator. Property damage can occur if the water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker. NOTE: Depending on your model, raise the wire shutoff arm

to OFF (up) position, or press the switch to OFF.

4. Empty the ice bin.

When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day ahead of time.

• Disconnect the water line from the back of the

refrigerator.

• When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or press the switch to OFF,

depending on your model.

2. Remove all food from the refrigerator and pack all frozen food in dry ice.

3. Empty the ice bin.

4. Turn off the Temperature control(s). See "Using the Control(s)."

5. Unplug refrigerator.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them together so they don't shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator so it rolls more easily OR raise the leveling screws so they don't scrape the floor. See "Leveling and Door Adjustment"

or "Door Closing and Door Alignment."

9. Tape the doors closed and tape the power cord to the back of the refrigerator.

When you get to your new home, put everything back and refer to the "Installation Instructions" section for preparation

instructions. Also, if your refrigerator has an automatic ice maker, remember to reconnect the water supply to the

refrigerator.

If You Choose to Turn Off the Refrigerator Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day ahead of time.

• When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or press the switch to OFF,

depending on your model.

Turn off the Temperature control(s). See "Using the Control(s)."

Clean refrigerator, wipe it, and dry well.

Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor

and mold from building up.

TROUBLESHOOTING

Try the solutionssuggestedhere firstbefore calling for assistance.

. _+,>= i = _i.? '_" _"i.

The refrigerator will not operate The refrigerator seems noisy

Refrigerator noise has been reduced over the years. Due to this reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below are listed some normal sounds with explanations.

• Pulsating - fans/compressor adjusting to optimize performance.

• Hissing/Rattling - flow of refrigerant, movement of water

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Power cord unplugged? Plug into a grounded 3 prong outlet.

Is outlet working? Plug in a lamp to see if the outlet is working.

Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker. If the problem continues, call an electrician.

Control(s) on? Make sure the refrigerator control is on. See "Using the Control(s)."

Is the refrigerator defrosting? Recheck to see whether the refrigerator is operating in 30 minutes. Your refrigerator will

regularly run an automatic defrost cycle.

New installation? Allow 24 hours following installation for the refrigerator to cool completely.

NOTE" Adjusting the temperature control(s) to coldest setting will not cool the refrigerator more quickly.

The motor seems to run too much

lines, or from items placed on top of the refrigerator.

• Popping - contraction/expansion of inside walls, especially during initial cool-down.

• Water running/dripping/sizzling - may be heard when ice melts during defrosting and water runs into the drain pan.

Water dripping onto the piping can be heard for a few minutes after the refrigerator stops running.

• Soft murmur/buzzing - the fan and air moving.

• Beeping - Door Ajar alarm (on some models) - If the door(s) are left open for more than 2 minutes, the Door Ajar alarm

will start beeping and will continue to beep until the door(s) are closed.

The door will not closecompletely

Door blocked open? Move food packages away from door.

Bin or shelf inthe way? Push bin or shelf back in the correct position.

Crisper cover in the way? Make sure the crisper cover is fully pushed in, so that the back rests on the supports.

Does the refrigerator wobble or seem unstable? Level the refrigerator. See "Leveling and Door Adjustment."

Were the doors removed during product installation and not properly replaced? Remove and replace the doors

according to "Refrigerator Doors," or call a qualified service technician.

Your new refrigerator may run longer than your old one due to its high-efficiency compressor and fans. The unit may run even

longer if the room is warm, a large food load is added, the door is opened often, or if the door has been left open.

The door isdifficult to open There isinterior moisture buildup

NOTE" Some moisture buildup is normal.

Humid room? Contributes to moisture buildup.

Door opened often or left open? Allows humid air to enter refrigerator. Minimize door openings and keep door fully

closed.

Control(s) setcorrectly for the surrounding conditions?Adjust

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

• Gaskets dirty or sticky? Clean gaskets and contact surfaces with mild soap and warm water. Rinse and dry with soft

cloth.

The lights do not work

the control(s) a setting colder. Check temperature in 24 hours. See "Using the Control(s)."

Are the air vents blocked in either compartment? This obstructs cold air movement between the compartments.

Remove any objects from in front of the air vents. See "Ensuring Proper Air Circulation" for the location of air

vents. Was a self-defrost cycle completed? It is normal for

droplets to form on the back wall after the refrigerator self- defrosts.

• is a light bulb loose in the socket or burned out? See "Changing the Light Bulbs."

Temperature is too warm

New installation? Allow 24 hours following installation for the refrigerator to cool completely.

Are the air vents blocked in either compartment? This obstructs cold air movement between the compartments.

Remove any objects from in front of the air vents. See "Ensuring Proper Air Circulation" for the location of air

vents. Door opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep door fully closed.

Large load of food added? Allow several hours for refrigerator to return to normal temperature.

Control(s) setcorrectly for the surrounding conditions? Adjust the control(s) a setting colder. Check temperature in 24 hours. See "Using the Control(s)."

The divider between the two compartments is warm

Internal heaters are used to reduce excess exterior moisture. If

still concerned, call for service.

There is water in the defrost drain pan

Is the refrigerator defrosting? The water will evaporate. It is normal for water to drip into the defrost pan.

Is it more humid than normal? Expect that the water in the defrost pan will take longer to evaporate. This is normal

when it is hot or humid.

_,Wc_te_

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce water flow. Straighten the water source line.

• Ice maker turned on? Make sure wire shutoff arm or switch (depending on model) is in the ON position.

• New installation? Wait 24 hours after ice maker installation for ice production to begin. Wait 72 hours for full ice

production.

• Large amount of ice recently removed? Allow 24 hours for ice maker to produce more ice.

• Ice cube jammed in the ice maker ejector arm? Remove ice from the ejector arm with a plastic utensil.

• Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure. See

"Water Supply Requirements."

+ 44 hidden pages