Kenmore 10644273600 Owner’s Manual

Side by Side Refrigerator

R_frig_rateur c6te & c6te

[- -q

Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com

2318526 Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8 www.sears.ca

TABLEOF CONTENTS

KENMORE APPLIANCE

WARRANTY ..................................................................................... 2

REFRIGERATOR SAFETY .............................................................. 3

Proper Disposal of Your Old Refrigerator .................................... 3

INSTALLATION INSTRUCTIONS .................................................. 4

Unpack the Refrigerator ............................................................... 4

Location Requirements ................................................................ 4

Electrical Requirements ................................................................ 5

Water Supply Requirements ........................................................ 5

Base Grille .................................................................................... 5

Refrigerator Doors ........................................................................ 6

Adjust the Doors ........................................................................... 7

Connect Water Supply ................................................................. 7

Normal Sounds ............................................................................. 7

REFRIGERATOR USE .................................................................... 8

Ensuring Proper Air Circulation .................................................... 8

Using the Controls ........................................................................ 8

Ice Maker and Storage Bin........................................................... 8

REFRIGERATOR FEATURES ........................................................ 9

Refrigerator Shelves ..................................................................... 9

Dell Drawer ................................................................................... 9

Convertible Vegetable/Meat Drawer, Crisper and Covers .......... 9

Convertible Vegetable/Meat Drawer Temperature Control ...... 10

Crisper Humidity Control ........................................................... 10

Wine Rack .................................................................................. 10

Utility Bin .................................................................................... 10

FREEZER FEATURES ................................................................. 10

Freezer Shelf .............................................................................. 10

Freezer Basket or Bin ................................................................ 11

DOOR FEATURES ....................................................................... 11

Door Rails or Bins ...................................................................... 11

Door Bins ................................................................................... 11

REFRIGERATOR CARE ............................................................... 11

Cleaning ..................................................................................... 11

Changing the Light Bulbs .......................................................... 12

Power Interruptions ................................................................... 13

Vacation and Moving Care ........................................................ 13

TROUBLESHOOTING .................................................................. 13

PROTECTION AGREEMENTS .................................................... 15

In the U.S.A ................................................................................ 15

In Canada .................................................................................. 15

Accessories ............................................................................... 15

SERVICE NUMBERS ............................................... BACK COVER

WARRANTY

ONE YEAR LIMITED WARRANTY

When installed, operated and maintained according to all

instructions supplied with the product, if this appliance fails due

to a defect in material or workmanship within one year from the

date of purchase, call 1-800-4-MY-HOME c_to arrange for free repair.

If this appliance is used for other than private family purposes,

this warranty applies for only 90 days from the date of purchase.

THIS WARRANTY COVERS ONLY DEFECTS IN MATERIAL AND WORKMANSHIP. SEARS WILL NOT PAY FOR:

1. Expendable items that can wear out from normal use, including but not limited to filters, belts, light bulbs, and bags.

2. A service technician to instruct the user in correct product installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed,

operated or maintained according to all instructions supplied with the product.

5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

Customer's sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Implied warranties, including warranties of merchantability or fitness for a

particular purpose, are limited to one year or the shortest period

allowed by law. Sears shall not be liable for incidental or

consequential damages. Some states and provinces do not allow the exclusion or limitation of incidental or consequential

damages, or limitations on the duration of implied warranties of

merchantability or fitness, so these exclusions or limitations may

not apply to you. This warranty applies only while this appliance is used in the

United States and Canada. This warranty gives you specific legal rights, and you may also

have other rights which vary from state to state.

Sears, Roebuck and Co.

Dept. 817WA, Hoffman Estates, IL 60179

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2B8

PRODUCT RECORD

In the space below, record your complete model number, serial

number, and purchase date. You can find this information on the

model and serial number label located on the product.

Have this information available to help you obtain assistance or

service more quickly whenever you contact Sears concerning your appliance.

Model number

Serial number

Purchase date

Save these instructions and your sales receipt for future

reference.

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet. • Use nonflammable cleaner.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all panels before operating.

• Remove doors from your old refrigerator, models).

SAVE THESE INSTRUCTIONS

• Keep flammable materials and vapors, such as gasoline, away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker kit ready models only).

• Use a sturdy glass when dispensing ice or water (on some

Proper Disposal ofYour Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Before you throw away your old refrigerator or freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily climb inside.

INSTALLATION INSTRUCTIONS

(,J a_S(.,_{ k@ ¢ s_cSk.._;;:.,./

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging Materials

Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information see "Refrigerator Safety."

When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.

Clean Before Using

After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in "Refrigerator Care."

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for W'

(1.25 cm) space on each side and at the top. When installing your refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum on each side (depending on your model) to allow for the door to swing open. If your refrigerator has an ice maker, allow extra space at the back for the water line connections.

NOTE: Do not install the refrigerator near an oven, radiator, or other heat source, nor in a location where the temperature will fall below 55°F (13°C).

V2" (1.25 cm)_

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when removing them to avoid impact from dropping.

2" 15.08cm)/

ElectricalShockHazard

Plugintoa grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15 or 20 amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an

extension cord. NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.

Water Pressure

A cold water supply with water pressure of between 30 and 120 psi (207-827 kPa) is required to operate ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).

If the ice maker is still not operating properly:

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If you have questions about your water pressure, call a licensed, qualified plumber.

Remove the Base Grille:

1. Open both doors.

2. Place hands along the ends of the grille. Push in on the top of the base grille and pull up on the bottom.

NOTE: Be sure to refasten the Tech Sheet behind the base grille after cleaning.

Read all directions carefully before you begin. IMPORTANT:

• If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

TOOLS NEEDED: Flat-blade screwdriver, 7/1611and 1/211open-end wrenches or two adjustable wrenches, 1/4"nut driver and drill bit, hand drill or electric drill (properly grounded).

NOTE: Your refrigerator dealer has a kit available with a 1/4" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or 3/16" (4.76 mm) saddle valve which reduces water flow and clogs more easily.

Replace the Base Grille:

1. Open both doors.

2. Line up the grille support tabs with the metal clips.

3. Push the grille firmly to snap it into place.

TOOLSNEEDED:1/4",1_,,,and%6"hex-headsocketwrenches,aflat-headscrewdriverandaPhillipsscrewdriver. IMPORTANT:Beforeyoubegin,turntherefrigeratorcontrolOFEUnplugrefrigeratorordisconnectpower.Removefoodandany

adjustabledoororutilitybinsfromdoors. NOTE:Itmayonlybenecessarytoremoveeitherthedoorhandleorthedoorstogetyourproductthroughthedoorwayofyour

residence.Measurethedooropeningtodeterminewhethertoremovetherefrigeratorhandlesorthedoors,

Door Removal

Top Left Hinge

A. Do Not Remove Screw

Top Right Hinge

Handle Removal

(Optional)

A. Do Not Remove Screw

Bottom Hinge

A. Do Not Remove Screw

Door Alignment

Handle Removal (optional)

1. Apply firm pressure with your hand on the face of trim, Slide top trim up and bottom trim down away from handle, Lift trim pieces off shoulder screws. See Graphic 1.

2. Remove handle screws and handles.

3. Move refrigerator into place. Replace handles as shown. See Graphic 1.

Door Removal

1. Unplug refrigerator or disconnect power.

2. Open both refrigerator doors. Remove the base grille by pulling up on the bottom outside corners. See Graphic 2,

Close both doors and keep them closed until you are ready to lift them free from the cabinet.

Remove top left hinge cover and screws as shown. See Graphic 3. Do not remove screw A.

Carefully lift freezer door straight up off bottom hinge. See Graphic 4.

Remove top right hinge cover and screws as shown. See Graphic 5. Do not remove screw A.

A. Leveling Screw

Carefully lift refrigerator door straight up off bottom hinge. See Graphic 4.

It may not be necessary to remove the bottom hinge to move the refrigerator through a doorway, Both bottom hinges have

similar construction,

• Disassemble the hinges as shown, See Graphic 6. Do not remove screw A.

Door and Hinge Replacement

1. Replace both bottom hinges, if removed. Tighten screws.

2. Replace the freezer door by carefully lifting the door onto the bottom left hinge,

NOTE: Provide additional support for the doors while the top hinges are being replaced. Do not depend on the door magnets

to hold the doors in place while you are working.

3. Align and replace the top left hinge as shown. See Graphic 3. Tighten screws.

4. Replace left hinge cover.

5. Replace the refrigerator door by carefully lifting the door onto the bottom right hinge.

6. Align and replace the top right hinge as shown. See Graphic 5. Tighten screws.

7. Replacehingecover.

8. Plugintoagrounded3prongoutlet.

Door Closing

Your refrigerator has two front adjustable rollers -- one on the right and one on the left. If your refrigerator seems unsteady or if you want the doors to close more easily, adjust the refrigerator's tilt using the instructions below:

1. Move the refrigerator into its final location.

2. The two leveling screws are part of the front roller assemblies which are at the base of the refrigerator on either side. See Graphic 7.

3. Use a hex-head socket wrench to adjust the leveling screws. Turn the leveling screw to the right to raise that side of the refrigerator or turn the leveling screw to the left to lower that side. It may take several turns of the leveling screws to adjust the tilt of the refrigerator. See Graphic 7.

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws and rollers. This makes it easier to adjust the screws.

4. Open both doors again and check to make sure that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns, and you should turn both leveling screws the same amount.

5. Replace the base grille. NOTE: Be sure to refasten the Tech Sheet behind the base

grille.

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the _/4"drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

1. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help prevent damage to the tubing when the refrigerator is pushed back against the wall.

2. Turn shutoff valve ON.

3. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a V2"to lY4" (1.25 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use _/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a grounded drill, drill a V4"hole in the cold water pipe you have selected.

_ ........A

G, .........C

A. Cold Water Pipe M Compression Sleeve B.Pipe Clamp F Shutoff Valve C. Copper Tubing G.Packing Nut D.Compression Nut

A. Tube Clamp B. Copper Tubing

4. The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the V4"(6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

5. Plug in refrigerator or reconnect power.

Your new refrigerator may make sounds that your old one didn't make. Because the sounds are new to you, you might be concerned about them. Most of the new sounds are normal. Hard

surfaces, such as the floor, walls, and cabinets, can make the sounds seem louder. The following describes the kinds of sounds

and what may be making them.

• If your product is equipped with an ice maker, you will hear a buzzing sound when the water valve opens to fill the ice maker for each cycle.

Your refrigerator is designed to run more efficiently to keep your food items at the desired temperatures and to minimize

energy usage. The high efficiency compressor and fans may cause your refrigerator to run longer than your old one. You

may also hear a pulsating or high-pitched sound from the compressor or fans adjusting to optimize performance.

• You may hear the evaporator fan motor circulating air through the refrigerator and freezer compartments. The fan speed

may increase as you open the doors or add warm food.

• Rattling noises may come from the flow of refrigerant, the water line, or items stored on top of the refrigerator.

C. Compression Nut D. Valve Inlet

Waterdrippingonthedefrostheaterduringadefrostcycle maycauseasizzlingsound.

Aseachcycleends,youmayhearagurglingsounddueto therefrigerantflowinginyourrefrigerator.

Contractionandexpansionoftheinsidewallsmaycausea poppingnoise.

Youmayhearairbeingforcedoverthecondenserbythe condenserfan.

Youmayhearwaterrunningintothedrainpanduringthe defrostcycle.

REFRIGERATOR USE

In order to ensure proper temperatures, you need to permit air to flow between the two sections. Cold air enters the bottom of the

freezer section and moves up. It then enters the refrigerator section through the top vent. Air then returns to the freezer as

shown.

Do not block any of these vents with food such as soda, cereal, bread, etc. Ifthe vents are blocked, airflow will be prevented and the temperature controls will not function properly.

IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent odor transfer from food, wrap or cover foods tightly.

Your model may have Rotary Controls or Slide Controls IMPORTANT:

• Your refrigerator will not cool when the Refrigerator Control is set to OFE

The Refrigerator Control adjusts the refrigerator compartment temperature. The Freezer Control adjusts the freezer compartment temperature. Higher numbered settings make the compartment colder. Lower numbered settings make the temperature less cold.

• Wait 24 hours before you put food into the refrigerator. If you add food before the refrigerator has cooled completely, your food may spoil.

NOTE: Adjusting the Refrigerator and Freezer Controls to a higher (colder) setting will not cool the compartments any

faster.

• The preset settings should be correct for normal household usage. The controls are set correctly when milk or juice is as

cold as you like and when ice cream is firm.

• If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.

For your convenience, your controls are preset at the factory. When installing your refrigerator, make sure that the controls are still preset to the "mid-settings" as shown.

Rotary Controls

FREEZER REFRIGERATOR

I'_ _'_ 2 5

COLD COLDER COLD 1 6 COLDER

Slide Controls

Freezer Refrigerator

C, )

cold 1 2 = 3 4 colder off I 2 A 3 4 colder

Adjusting Controls

NOTE: Wait at least 24 hours between adjustments and then

recheck the temperatures. If you need to adjust temperatures, adjust the refrigerator

temperature first.

Rotary Controls

Turn the control right (clockwise) to make the compartment

colder. Turn the control left (counterclockwise) to make it less cold.

Slide Controls

Slide the control one setting to the right to make the compartment colder. Slide the control one setting to the left to

make it less cold.

CONDITION/REASON: SETTING

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR

- Not set correctly for your Control one setting conditions lower

REFRIGERATOR too warm REFRIGERATOR

- Door opened often, large amount Control one setting of food added or room temperature higher

very warm FREEZER too cold FREEZER Control one

- Not set correctly for your setting lower conditions

FREEZER too warm/too little ice FREEZER Control one

- Door opened often, or large setting higher amount of food added or very cold

room temperature (can't cycle often enough) or heavy ice usage

{<'t so _s÷_'_oce s ,,Accesso y

Turning the Ice Maker On/Off

NOTE: Do not force the wire shutoff arm up or down.

The on/off switch for the ice maker is a wire shutoff arm located

on the side of the ice maker.

1. To turn the ice maker on, simply lower the wire shutoff arm.

NOTE:Youricemakerhasanautomaticshutoff.Asiceis made,theicecubeswillfilltheicestoragebinandtheice

cubeswillraisethewireshutoffarmtotheOFF(armup) position.

Tomanuallyturntheicemakeroff,liftthewireshutoffarmto theOFF(armup)positionandlistenfortheclicktomakesure theicemakerwillnotcontinuetooperate.

Increasing Ice Production Rate

The ice maker should produce approximately 7 to 9 batches of ice in a 24-hour period. If ice is not being made fast enough, turn

the Freezer Control toward a higher (colder) number in half number steps. (For example, if the control is at 3, move it to

between 3 and 4.) Wait 24 hours between each increase.

Remember

• Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

• Do not store anything on top of the ice maker or in the ice storage bin.

Shelves and Shelf Frames

To remove and replace a shelf/frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into the shelf supports. Tilt the front of the shelf up until rear shelf hooks drop into the shelf supports. Check to make sure that the shelf is securely in position.

{o/s so_e _'_sodeB>}

The dell drawer stores raisins, nuts, spreads, and other small items at normal refrigerator temperatures.

To Remove and Replace the Dell Drawer:

1. Remove the dell drawer by sliding it straight out to the stop. Lift the front and slide the drawer out the rest of the way.

2. Replace the dell drawer by sliding it back past the stop.

REFRIGERATOR FEATURES

Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please call the toll-free number on the cover or in the "Accessories"

section.

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when removing them to avoid impact from dropping.

Your model may have glass or wire shelves. Store similar foods together and adjust the shelves to fit different heights. This reduces the time the refrigerator door is open and saves energy.

Crisper and Convertible Vegetable Meat Drawers

To Remove and Replace Drawers:

1. Slide crisper or meat drawer straight out to the stop. Lift the front of drawer with one hand while supporting the bottom of

drawer with other hand and slide the drawer out the rest of the way.

2. Replace the crisper or meat drawer by sliding it back in fully past the drawer stop.

Crisper or Vegetable/Meat Drawer Covers

To Remove and Replace Covers:

1. Remove the crisper and meat drawer. Press up in center of crisper glass insert until it rises above the plastic frame. Holding the crisper glass firmly, carefully slide the glass insert

forward to remove.

2. Lift crisper cover frame and remove. Repeat steps to remove the meat drawer cover.

3. Replacebackofmeatdrawercoverframeintosupportsor slidesonsidewallsoftherefrigeratorandlowerorslidethe frontofthecoverframeintoplace.

4. Sliderearofglassinsertintocoverframeandlowerfrontinto place.Repeatstepstoreplacethecrispercover.

T )mpe@tu s Co stro

The convertible vegetable/meat drawer can be adjusted to properly chill meats or vegetables. The air inside the pan is cooled to prevent "spot" freezing and can be set to keep meats at the National Livestock and Meat Board recommended storage temperatures of 28°- 32°F (-2°- 0°C).

IMPORTANT: To extend freshness, wrap meats in airtight, moisture-proof materials before storing. Always store meat as

recommended.

Adjusting the Control

The convertible control comes preset at the lowest meat setting. To change a control setting: Move the control to the right

(colder) or to the left (less cold) as desired. To store vegetables: Set the control to VEG (all the way to the

left) to store vegetables at their optimal storage temperatures (which need to be warmer than those for meat).

HIGH (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

• Leafy vegetables: Wash in cold water, drain and trim or tear off bruised and discolored areas. Place in plastic bag or plastic container and store in crisper.

Humidity Control Location:

• Humidity Control on crisper drawer.

Wi ,e Rack

{on some _'_sode/s ,,.A_;x::ssorT}

To Remove and Replace the Wine Rack:

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the wall of the refrigerator.

IMPORTANT: Iffood starts to freeze, move the control to the left (less cold). Remember to wait 24 hours between adjustments. Doing so gives the temperature of the food time to change.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following chart for storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish ......................... use same day as purchased

Chicken, ground beef, variety meat (liver, etc.) ................ 1-2 days

Cold cuts, steaks/roasts ................................................... 3-5 days

Cured meats ................................................................... 7-10 days Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

=.,_.......i._,..,.. 111Jll Ol[y *JOYI_, _. I

You can control the amount of humidity in the moisture-sealed crisper. Adjust the control to any setting between LOW and

HIGH. LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

• Fruit: Wash, let dry and store in refrigerator in plastic bag or crisper. Do not wash or hull berries until they are ready to use. Sort and keep berries in original container in crisper, or store in a loosely closed paper bag on a refrigerator shelf.

• Vegetables with skins: Place in plastic bag or plastic container and store in crisper.

NOTE: For long-term storage, place eggs in a covered container or in their original carton on an interior shelf.

FREEZER FEATURES

Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word "Accessory." Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Accessories" section.

@umbe_ c,_'shelves vs'_Aes with mode_}

To Remove and Replace the Shelf:

1. Lift the shelf off of the supports.

2. Slide it out of the shelf support holes.

3. Replace shelf in the reverse order.

Frozen Food Storage Guide

Drop-in Door Rails

Storage times will vary according to the quality and type of food, the type of packaging or wrap used (should be airtight and moisture-proof), and the storage temperature. Ice crystals inside a sealed package are normal. This simply means that moisture in the food and air inside the package have condensed, creating ice crystals.

Put no more unfrozen food into the freezer than will freeze within 24 hours (no more than 2 to 3 Ibs. of food per cubic foot

[907-1,360 g per 28 L] of freezer space). Leave enough space in the freezer for air to circulate around packages. Be careful to leave enough room for the door to close tightly.

For more information on preparing food for freezing, check a freezer guide or reliable cookbook.

_:_a£!_c bn on so_,sse_'Ts©des

The freezer basket or bin can be used to store bags of frozen fruits and vegetables that may slide off freezer shelves.

To Remove and Replace the Freezer Basket or Bin:

1. Remove basket or bin by sliding it out to the stop.

2. Lift the front of the basket or bin and slide it out the rest of the way.

To Remove and Replace the Rails:

1. Remove the rails by pulling straight up on each end of the rail.

2. Replace the rails by sliding the shelf rail into the slots on the door and pushing the rail straight down until it stops.

To Remove and Replace the Bins:

1. Remove the bin by lifting it and pulling it straight out.

2. Replace the bin by sliding it in above the desired support and pushing it down until it stops.

REFRIGERATOR CARE

3. Replace the basket or bin by positioning it on the side wall

guide rails. Lift the basket or bin front slightly while pushing it past the guide rail stops and slide basket or bin in the rest of

the way.

DOOR FEATURES

call the toll-free number on the cover or in the "Accessories" section.

©oo Ras or Bns

The door rails may be removed for easier cleaning.

Snap-on Door Rails or Bins

To Remove and Replace the Rails or Bins:

1. Remove the rails by pushing in slightly on the front of the

bracket while pulling out on the inside tab. Repeat these steps for the other end of the rail.

2. Replace the rails by aligning the ends of the brackets with the buttons on the sides of the door liner. Firmly snap bracket and rail assembly onto the tabs above the shelf as shown.

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to prevent odors from building up. Wipe up spills immediately.

To Clean Your Refrigerator:

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves, crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools. These can scratch or damage materials.

• To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs. to 1 qt. [26 g to 0.95 L] of water).

Determine whether your refrigerator exterior is painted metal, brushed aluminum or stainless steel and choose the

appropriate cleaning method. Painted metal: Wash exteriors with a clean sponge or soft

cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth. For additional protection against damage to painted metal exteriors, apply appliance wax (or auto paste wax) with a clean, soft cloth. Do not wax plastic parts.

Brushed aluminum: Wash with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth.

Stainless steel finish: Wash with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners. Dry thoroughly with a soft cloth.

To keep your stainless steel refrigerator looking like new and to remove minor scuffs or marks, it is suggested that you use the manufacturer's approved Stainless Steel

Cleaner & Polish.

IMPORTANT: This cleaner is for stainless steel parts only! Do not allow the Stainless Steel Cleaner & Polish to come into

contact with any plastic parts such as the trim pieces, dispenser covers or door gaskets. If accidental contact does occur, clean plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft cloth. To order the cleaner, see the "Accessories" section.

There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.

Ifyou need to clean the condenser:

• Remove the base grille. See "Base Grille" graphic or "Base Grille" section.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

Refrigerator Control Panel Light

Reach behind the refrigerator control panel to remove and replace light bulb.

Crisper Lights

• If necessary, remove the top crisper drawer to access the crisper light shield. Remove the light shield by lifting the ends

out of the brackets as shown.

• Replace the light shield by inserting the ends into the brackets. If necessary, replace the top crisper drawer.

Upper Freezer Light (on some models)

Style 1

• Remove light shield by grasping the top center of the shield and pulling forward while turning it slightly to one side. If

necessary, remove top crisper drawer to gain access to the crisper light shield.

Replace the light shield by inserting the tabs on one end into the slotted holes in the refrigerator or freezer liner. Then, carefully bend the shield at the center to insert the tabs on

the other end.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to replace the bulb with one of the same size and shape. All lights require a 40-watt appliance bulb. Replacement bulbs are available from your dealer.

1. Unplug refrigerator or disconnect power.

2. Remove light shield when applicable as shown. NOTE: To clean the light shield, wash it with warm water and

liquid detergent. Rinse and dry the shield well.

3. Remove light bulb and replace with one of the same size, shape and wattage.

4. Replace light shield when applicable as shown.

5. Plug in refrigerator or reconnect power.

Style 2

• Remove the light shield by squeezing the sides of the light shield in toward the center while pulling the shield forward as shown.

• Replace the light shield by fitting the tabs into the slotted holes in the freezer liner. Push in the shield until it snaps into

place.

If the power will be out for 24 hours or less, keep the door or doors closed (depending on your model) to help food stay cold

and frozen. If the power will be out for more than 24 hours, do one of the

following:

• Remove all frozen food and store it in a frozen food locker.

• Place 2 Ibs (907 g) of dry ice in the freezer for every cubic foot (28 L) of freezer space. This will keep the food frozen for 2 to 4 days.

• If neither a food locker nor dry ice is available, consume or can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled one. A freezer full of meat stays cold longer than a freezer full of baked goods. If you see that food contains ice crystals, it may be refrozen, although the quality and flavor may be affected. If the condition of the food is poor, dispose of it.

Vacations

If You Choose to Leave the Refrigerator On While You're Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

• Raise wire shutoff arm to OFF (up) position or move the

switch to the OFF (right) setting.

• Shut off water supply to the ice maker.

3. Empty the ice bin.

If You Choose to Turn the Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF (right) setting.

3. Depending on the model, turn the Thermostat Control or Refrigerator Control to OFE See the "Using the Control(s)"

section.

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and mold from building up.

Moving

When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• Disconnect the water line from the back of the

refrigerator.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF (right) setting.

2. Remove all food from the refrigerator and pack all frozen food in dry ice.

3. Empty the ice bin.

4. Depending on the model, turn the Thermostat Control or Refrigerator Control to OFE See the "Using the Control(s)"

section.

5. Unplug refrigerator.

6. Empty water from the defrost pan.

7. Clean, wipe, and dry thoroughly.

8. Take out all removable parts, wrap them well, and tape them together so they don't shift and rattle during the move.

9. Depending on the model, raise the front of the refrigerator so it rolls more easily OR screw in the leveling legs so they don't scrape the floor. See the "Adjust the Doors" section.

f0. Tape the doors closed and tape the power cord to the

refrigerator cabinet.

When you get to your new home, put everything back and refer to the "Installation Instructions" section for preparation instructions. Also, if your refrigerator has an automatic ice maker, remember to reconnect the water supply to the refrigerator.

TROUBLESHOOTING

Trythe solutions suggested here first in order to avoid the cost of an unnecessary service call.

Your refrigerator will not operate

• Is the power supply cord unplugged? Plug into a grounded 3 prong outlet.

• Has a household fuse blown or circuit breaker tripped? Replace the fuse or reset the circuit breaker.

• Is the refrigerator or freezer control turned to the OFF position? See the "Using the Controls."

• Is the refrigerator defrosting? Recheck to see if the refrigerator is operating in 30 minutes. Your refrigerator will regularly run an automatic defrost cycle.

The lights do not work

• Is the power supply cord unplugged? Plug into a grounded 3 prong outlet.

• Is a light bulb loose in the socket or burned out? See "Changing the Light Bulb(s)."

There is water in the defrost drain pan

• Is the refrigerator defrosting? The water will evaporate. It is normal for water to drip into the defrost pan.

• Is it more humid than normal? When it is humid, expect that the water in the defrost pan will take longer to evaporate.

Themotorseemstoruntoomuch

Off-taste, odor or gray color in the ice

Is the room temperature hotter than normal? The motor

will run longer under warm conditions. At normal room temperatures, expect your motor to run about 40% to 80% of the time, Under warmer conditions, it will run even more,

Has a large amount of food just been added to the refrigerator? Adding a large amount of food warms the

refrigerator. The motor normally will run longer to cool the refrigerator back down.

Are the doors opened often? The motor will run longer when this occurs. Conserve energy by getting all items out at one time, keeping food organized, and closing the door as soon as possible.

Are the controls not set correctly for the surrounding conditions? See" Using the Controls."

Are the doors not closed completely? Close the doors

firmly. If they do not close completely, see "The doors will not close completely" later in this section.

Are the condenser coils dirty? This prevents air transfer and makes the motor work harder. Clean the condenser coils, See

"Cleaning," Are the door gaskets not sealed all the way around?

Contact atechnician or other qualified person. NOTE: Your new refrigerator will run longer than your old one

due to its high efficiency motor.

The refrigerator seems to make too much noise

• The sounds may be normal for your refrigerator. See "Normal Sounds."

The ice maker is not producing ice or not enough ice

• Has the ice maker just been installed? Wait 72 hours for full ice production to begin. Once your refrigerator is cooled, the

ice maker should produce 70 to 120 cubes every 24 hours,

Is the ice maker wire shutoff arm in the OFF (wire shutoff arm up) position (on some models)? Lower wire shutoff arm

to the ON (wire shutoff arm down) position. See "Ice Maker and Storage Bin."

Is the water line shutoff valve to the refrigerator not turned on? Turn on the water valve. See "Connect Water

Supply." Is an ice cube jammed in the ice maker ejector arm?

Remove the ice from the ejector arm with a plastic utensil. See "Ice Maker and Storage Bin,"

Does the ice maker mold have water in it or has no ice been produced? Make sure your refrigerator has been

connected to a water supply and the supply shutoff valve is turned on, See "Connect Water Supply."

Has a large amount of ice just been removed? Allow 24 hours for ice maker to produce more ice.

Are the controls set correctly? See the "Using the Controls,"

NOTE: If not due to any of the above, there may be a problem with the water line. Call for service.

• Are the plumbing connections new, causing discolored or off-flavored ice? Discard the first few batches of ice.

• Have the ice cubes been stored too long? Throw old ice away and make a new supply.

• Does the freezer and ice bin or bucket need to be cleaned? See the "Cleaning" or "Ice Maker and Storage Bin."

• Has food in the freezer or refrigerator been wrapped properly? Use airtight, moisture-proof packaging to help prevent odor transfer to stored food.

• Does the water contain minerals (such as sulfur)? A filter may need to be installed to remove the minerals.

The divider between the two compartments is warm

The warmth is probably due to normal operation of the automatic exterior moisture control. If still concerned, call for service.

Temperature is too warm

Are the air vents blocked in either compartment? This

prevents the movement of cold air from the freezer to the refrigerator. Remove any objects from in front of the air vents, See "Ensuring Proper Air Circulation" for the location of air

vents, Are the door(s) opened often? The refrigerator will warm

when this occurs. Keep the refrigerator cool by getting all items out at one time, keeping food organized, and closing

the door as soon as possible.

Has a large amount of food just been added to the refrigerator or freezer? Adding a large amount of food

warms the refrigerator. It can take several hours for the refrigerator to return to the normal temperature,

Are the controls set correctly for the surrounding conditions? See the "Using the Controls,"

There is interior moisture build-up

• Are the air vents blocked in the refrigerator? Remove any objects from in front of the air vents. See "Ensuring Proper Air

Circulation" for the location of air vents.

• Are the door(s) opened often? Avoid humidity build-up by getting all items out at one time, keeping food organized, and closing the door as soon as possible.

• Is the room humid? It is normal for moisture to build up inside the refrigerator when the room air is humid,

• Is the food packaged correctly? Check that all food is securely wrapped. Wipe off damp food containers before placing in the refrigerator.

• Are the controls set correctly for the surrounding conditions? See the "Using the Controls."

• Was a self-defrost cycle completed? It is normal for droplets to form after the refrigerator self-defrosts.

The doors will not close completely

• Are food packages blocking the door open? Rearrange containers so that they fit more tightly and take up less

space. Is the ice bin or ice bucket out of position? Push the ice

bin in all the way, If the ice bin does not go in all the way, it may not be put in straight. Pull it out and try again, See the "Ice Maker and Storage Bin."

Are the pans, shelves, bins, or baskets out of position? Put the crisper cover and all pans, shelves, bins, and baskets back into their correct positions. See "Crisper and Crisper

Covers."

PROTECTION AGREEMENTS

Master Protection Agreements

Congratulations on making a smart purchase. Your new Kenmore ®product is designed and manufactured for years of dependable operation. But like all products, it may require preventive maintenance or repair from time to time. That's when having a Master Protection Agreement can save you money and aggravation.

Purchase a Master Protection Agreement now and protect

yourself from unexpected hassle and expense.

The Master Protection Agreement also helps extend the life of your new product. Here's what's included in the Agreement:

v' Expert service by our 12,000 professional repair specialists v' Unlimited service and no charge for parts and labor on all

covered repairs "No-lemon" guarantee - replacement of your covered

product if four or more product failures occur within twelve months

v' Product replacement if your covered product can't be fixed v' Annual Preventive Maintenance Check at your request - no

extra charge

v' Fast help by phone - phone support from a Sears technician

on products requiring in-home repair, plus convenient repair scheduling

v' Power surge protection against electrical damage due to

power fluctuations

v' Rental reimbursement if repair of your covered product takes

longer than promised

Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night, or schedule a service appointment online.

Sears has over 12,000 professional repair specialists, who have access to over 4.5 million quality parts and accessories. That's the kind of professionalism you can count on to help prolong the life of your new purchase for years to come. Purchase your Master Protection Agreement today!

Some limitations and exclusions apply. For prices and additional information, call 1-800-827-6655.

• Are the gaskets sticking? Clean gaskets according to the directions in the "Cleaning" section,

• Does the refrigerator wobble or seem unstable? Level the refrigerator. See "Door Closing" or "Leveling Refrigerator," depending on your model.

Were the doors removed during product installation and not properly replaced? Remove and replace the doors according to the "Refrigerator Door" section on some models, or call a qualified service technician.

The doors are difficult to open

• Are the gaskets dirty or sticky? Clean gaskets according to the directions in the "Cleaning" section.

Sears Installation Service For Sears professional installation of home appliances, garage

door openers, water heaters, and other major home items, in the U.S.A. call 1-800-4-MY-HOME ®.

Maintenance Agreements

Your purchase has added value because you can depend on Sears HomeCentral ®for service. With over 2,400 Service

Technicians and more than a million parts and accessories, we have the tools, parts, knowledge and skills to back our pledge:

We Service What We Sell. Your Kenmore ®product is designed, manufactured and tested to

provide years of dependable operation. But like all products, it may require service from time to time, The Sears Maintenance Agreement offers you an outstanding service program, affordably priced.

The Sears Maintenance Agreement

• Is your way to buy tomorrow's service at today's price

• Eliminates repair bills resulting from normal wear and tear

• Provides phone support from a Sears technician on products requiring in-home repair

• Even if you don't need repairs, provides an annual Preventive Maintenance Check, at your request, to ensure that your product is in proper running condition.

Some limitations apply. For more information about Sears

Canada Maintenance Agreements, call 1-800-361-6665.

Replacement Parts

To order stainless steel cleaner, please call 1-800-4-MY-HOME ® and ask for the appropriate part number listed below, or contact

your authorized Kenmore dealer. Stainless Steel Cleaner & Polish:

Order Part #D22 M40083 R

+ 33 hidden pages