Page 1
FastMig
KM 300, 400, 500
Operating manual
Käyttöohje
Bruksanvisning
Bruksanvisning
Brugsanvisning
Gebrauchsanweisung
Gebruiksaanwijzing
Manuel d’utilisation
Manual de instrucciones
Instrukcja obsługi
Инструкции по эксплуатации
操作手册
Manual de utilização
Manuale d’uso
EN
FI
SV
NO
DA
DE
NL
FR
ES
PL
RU
ZH
PT
IT
Page 2
Page 3
EN
OPERATING MANUAL
English
Page 4
EN
CONTENTS
1. Johdanto ....................................................................................... 3
1.1 Yleistä .......................................................................................................................................... 3
1.2 Laitteen esittely ....................................................................................................................... 4
2. Käyttöönotto ................................................................................5
2.1 Laitteen sijoittaminen ........................................................................................................... 5
2.2 Sähkönjakeluverkko .............................................................................................................. 5
2.3 Liittäminen sähköverkkoon ................................................................................................ 6
2.4 Hitsaus- ja maadoituskaapelit ........................................................................................... 6
3. Laitteen käyttö ............................................................................. 7
3.1 Virtalähteen käynnistäminen ............................................................................................. 7
3.2 Etupaneelin merkkivalot ..................................................................................................... 7
3.3 Ohjauspaneelin käyttö ......................................................................................................... 8
3.3.1 Ohjauspaneelin käynnistäminen ................................................................................... 8
3.3.2 Näytöt .............................................................................................................................. 8
3.3.3 Säätönupit ........................................................................................................................ 8
3.3.4 MIG-dynamiikan säätö (Arc Force) ................................................................................. 8
3.3.5 Kaasunvirtauksen testaus ............................................................................................... 8
3.3.6 Langan kylmäajo (Wire Inch) .......................................................................................... 8
3.3.7 Neste- tai kaasujäähdytteisen MIG-pistoolin valinta..................................................... 8
3.3.8 Weld data -tietojen haku ................................................................................................. 9
3.3.9 Ohjauspaneelin valinta ................................................................................................... 9
3.3.10 MIG-toimintatavan valinta .............................................................................................. 9
3.3.11 Toimintaparametrien asetus ........................................................................................... 9
3.3.12 Langansyöttönopeuden kalibrointi .............................................................................10
4. Vikatilanteet ............................................................................... 11
4.1 Ylikuormitus (keltainen merkkivalo syttyy) ................................................................ 11
4.2 Ohjauskaapeliliitännän sulake ........................................................................................11
4.3 Yli- tai alijännitteinen sähköverkko ...............................................................................11
4.4 Vaiheen puuttuminen sähköverkosta ..........................................................................11
4.5 Laitteen vikakoodit ..............................................................................................................12
5. Huolto ......................................................................................... 13
5.1 Kaapelit ....................................................................................................................................13
5.2 Virtalåhde ................................................................................................................................13
5.3 Määräaikaishuollot ..............................................................................................................13
6. Tuotteen hävittäminen ............................................................. 14
7. Tilausnumerot ............................................................................ 14
8. Tekniset tiedot ........................................................................... 15
FastMig 300, 400, 500
2
Page 5
EN
1. PREFACE
1.1 General
Congratulations on choosing the FastMig™ KM equipment. Used correctly, Kemppi products
can signicantly increase the productivity of your welding, and provide years of
economical service.
This operating manual contains important information on the use, maintenance and safety of
your Kemppi product. The technical specications of the equipment can be found at the end
of the manual.
Please read the manual carefully before using the equipment for the rst time. For your
own safety and that of your working environment, pay particular attention to the safety
instructions in the manual.
For more information on Kemppi products, contact Kemppi Oy, consult an authorised Kemppi
dealer, or visit the Kemppi web site at www.kemppi.com.
The specications presented in this manual are subject to change without prior notice.
Important notes
Items in the manual that require particular attention in order to minimise damage and
personal harm are indicated with the ’NOTE!’ notation. Read these sections carefully and follow
their instructions.
Disclaimer
While every eort has been made to ensure that the information contained in this guide
is accurate and complete, no liability can be accepted for any errors or omissions. Kemppi
reserves the right to change the specication of the product described at any time without
prior notice. Do not copy, record, reproduce or transmit the contents of this guide without
prior permission from Kemppi.
3
© Kemppi Oy / 1152
Page 6
EN
1.2 Introduction
The FastMig KM-series power sources 300, 400, and 500 are MIG power sources designed
for demanding professional use in the three-phase network. The power source has a control
panel that allows ready control of the functions of the power source and the wire feeder.
Overview of the power source
A4
A2
A5
A6
A7
A8
A9
A1
A11
A3
A10
Front view Rear view
A1 Control panel
A2 Main switch
A3 Signal light (I/O)
A4 Thermal warning light
A5 Welding cable connection
A6 Earth connection
A7 Control cable connection
A8 Mains cable input
A9 Fuse for control cable connection (6.3 A slow)
A10 Fan grills
A11 Carrying handles
FastMig 300, 400, 500
4
Page 7
EN
2. INSTALLATION
2.1 Positioning of the machine
Place the machine on a rm, dry and level surface. Where possible, do not allow dust or other
impurities to enter the machines cooling air ow. Preferably site the machine above oor level;
for example on a suitable carriage unit.
Notes for positioning the machine
• The surface inclination should not exceed 15 degrees.
• Ensure the free circulation of the cooling air. There must be at least 20 cm of free space in
front of and behind the machine for cooling air to circulate.
• Protect the machine against heavy rain and direct sunshine.
NOTE! The machine should not be operated in the rain as the protection class of the machine,
IP23S, allows for outside preserving and storage only.
NOTE! Never aim metallic grinding spray/sparks towards the equipment.
2.2 Distribution network
All regular electrical devices without special circuits generate harmonic currents into
distribution network. High rates of harmonic current may cause losses and disturbance to
some equipment.
FastMig KM 500:
This equipment complies with IEC 61000-3-12 provided that the short-circuit power Ssc
is greater than or equal to 4.6 MVA at the interface point between the user's supply and
the public supply network. It is the responsibility of the installer or user of the equipment
to ensure, by consultation with the distribution network operator if necessary, that the
equipment is connected only to a supply with a short-circuit power Ssc greater than or equal
to 4.6 MVA.
FastMig KM 400:
This equipment complies with IEC 61000-3-12 provided that the short-circuit power Ssc
is greater than or equal to 4.7 MVA at the interface point between the user's supply and
the public supply network. It is the responsibility of the installer or user of the equipment
to ensure, by consultation with the distribution network operator if necessary, that the
equipment is connected only to a supply with a short-circuit power Ssc greater than or equal
to 4.7 MVA.
FastMig KM 300:
WARNING: This equipment does not comply with IEC 61000-3-12. If it is connected to a public
low voltage system, it is the responsibility of the installer or user of the equipment to ensure,
by consultation with the distribution network operator if necessary, that the equipment may
be connected.
5
© Kemppi Oy / 1152
Page 8
EN
2.3 Connection to mains
FastMig KM power sources are connected to the 400-V three-phase network using the mains
cable supplied with the machine.
The machine is equipped with a ve-metre mains cable that does not have a plug. Before use,
check the mains cable and install a mains plug. If the cable does not comply with the local
electrical regulations, replace it with a compliant cable. See ’Technical specications’.
NOTE! The mains cable or plug may be installed or replaced by only an electrical contractor or
installer authorised to perform such operations.
Replacement of the mains cable
1. Unscrew the mounting screws on the top and sides of the machine, and remove the case
by lifting it.
2. Disconnect the phase leads from connectors L1, L2, and L3, and disconnect the
protective earth lead.
3. Pass the cable to the machine through the inlet ring at the rear of the machine, and
secure the cable with a cable clamp.
4. Connect the cable’s phase leads to connectors L1, L2, and L3.
5. Connect the yellow-green protective earth lead to its connector .
NOTE! Do not connect the zero lead if you are using a ve-lead cable.
The table below lists the fuse sizes for 100% load in a 400-V three-phase network with
4 x 10-mm² cable for dierent power source models.
Model Fuse
KM 300 20 A delayed
KM 400 25 A delayed
KM 500 35 A delayed
2.4 Welding and earthing cables
The device has a welding cable connection both in the front and in the rear. The positions of
the welding and earthing cable connections are shown earlier in section ‘Introduction’.
The welding cable type to be used is rubber-insulated copper cable. The recommended crosssections of the cables for dierent power source models are as follows:
Model Cross-section
KM 300 50 – 70 mm²
KM 400 70 – 90 mm²
KM 500 70 – 90 mm²
The table below shows the typical load capacities of the cables when the ambient
temperature is 25 °C and the lead temperature is 85 °C.
Cable Duty cycle (ED) Voltage loss / 10 m
100 % 60 % 35 % 20 %
50 mm² 285 A 316 A 371 A 458 A 0,35 V / 100 A
70 mm² 355 A 403 A 482 A 602 A 0,25 V / 100 A
95 mm² 430 A 498 A 606 A 765 A 0,18 V / 100 A
120 mm² 500 A 587 A 721 A 917 A 0,21 V / 100 A
NOTE! Do not overload the welding cables, as an overload may cause voltage loss and
overheating.
Connect the earth clamp directly to the work piece in such a way as to maximise the contact
surface of the clamp. The point of connection must be unpainted and free of corrosion.
FastMig 300, 400, 500
6
Page 9
EN
3. MACHINE USE
3.1 Starting of the power source
Start the power source by turning the main switch (A2) on the front panel to the ‘I’ position.
The standby indicator (A3) turns on. The control panel and wire feeder are not operational yet,
and the text ‘OFF’ is shown on the control panel display.
NOTE! Always turn the device on and o using the main switch, not via the mains socket.
The cooling fan is started for a moment when the main switch is turned to the ‘I’ position. The
fan turns o after a while and then restarts during welding when the machine has warmed up
suciently. The fan continues running even after up to 10 minutes of welding, depending on
the temperature of the machine.
3.2 Front panel indicators
The following indicators can be found on the front panel of the device:
• When the green indicator, A3, is on, the power source is in standby mode. This indicator
is on when the machine is connected to the mains supply with the main switch in the ‘I’
position.
• When the yellow overheating indicator (A4) is on, the machine has overheated. The fan
then starts. When the indicator turns o, the machine can be used again.
• When indicator A4 blinks, the machine has experienced a failure. Attempt to remedy the
problem according to the instructions in Section 4, ‘Troubleshooting’. If the failure cannot
be eliminated, turn o the machine, and turn it on again. If the failure persists, write
down any fault code that may be shown on the display and contact authorised Kemppi
service agent.
GAS TEST
DYNAMICS
WIRE INCH
weld
data
V
A
m/min
4T
SETUP
2T
KM
W001319
LOCAL
REMOTE
P1 P2
P9P7
P3 P4 P5
P10
P6
P8
7
© Kemppi Oy / 1152
Page 10
EN
3.3 Use of the control panel
The control panel is used for controlling and monitoring the operation of the power source
and the wire feeder. The buttons are used for adjusting functions. The displays and indicators
reect the operating modes of the machine.
3.3.1 Starting of the control panel
• When you start the power source with the main switch (A2), the control panel remains in
OFF mode and the wire feeder is not operational. The display shows the text ‘OFF’.
• When you depress the start button P1 for at least one second, the control panel starts.
The unit is now ready for welding and enters the mode that was active before the power
was cut o.
• You can also start the control panel by quickly pressing the welding gun switch three
times.
3.3.2 Displays
• When you are adjusting the machine settings, the control panel displays show adjustable
operation parameters, their values, and the units of measure.
• During welding, display P2 shows the welding current value that is currently in use, while
display P6 shows the welding voltage.
3.3.3 Control knobs
• The left-hand control knob (P8) allows adjustment of the speed of wire feeding. The
selected speed is shown on the display on the left-hand side (P2).
• The control knob on the right-hand side (P9) allows you to adjust the welding voltage.
The selected voltage is shown on the right-hand display (P6).
These adjusters are used also for selecting the values of the machine’s operational parameters,
such as the MIG mode and set-up features. A parameter for adjustment is selected with the
left-hand knob knob (P8), while the value of the parameter is selected with the right-hand
knob (P9).
3.3.4 Adjustment of MIG dynamics (arc force)
When you press button P3, you can adjust the MIG welding dynamics of the machine by
means of the right-hand knob, P9. The welding dynamics setting aects the properties of the
welding arc and the amount of spatter as follows:
• The value 0 is the recommended basic setting.
• Use values -9 … -1 if you want a softer arc and less spatter.
• Use values 1 – 9 if you want a rougher and more stable arc. This setting is useful when
you are using 100% CO₂-shielding gas when welding steel.
3.3.5 Gas test
The gas test button (P4) opens the gas valve without activating the wire feed or power source.
By default, gas ows for 20 seconds. The gas ow time remaining is shown on the display.
The right-hand knob (P9) allows you to set the default gas ow time, between 10 – 60
seconds, and store the new default value in the machine’s memory. To abort the gas test, press
the start button or gun switch.
3.3.6 Wire Inch
When you press the Wire inch button, P5, the wire feeder engine starts but the gas valve does
not open and the power source is not activated. The default wire feed speed is 5 m/min, and
you can adjust the speed with the right-hand knob. When the button is released, the wire
feeding stops. The machine automatically goes back to the normal state after approximately
ve seconds from release of the button or immediately when you press the start button.
FastMig 300, 400, 500
8
Page 11
EN
3.3.7 Selection of liquid- or gas-cooled MIG gun
You can select a MIG gun cooled with liquid or gas by pressing buttons 3 and 5 simultaneously
and holding them down for at least one second.
• When the display reads ‘GAS’, you can use a gas-cooled MIG gun with the equipment.
• When the display reads ‘COOLEr’, you can use a liquid-cooled MIG gun with the
equipment.
You can change the gun selection by pressing buttons P3 and P4 again, as above. With a
liquid-cooled gun selected, the liquid cooling function is started when the power source is
started the next time.
3.3.8 Retrieval of weld data
The weld data function allows you to return to the welding current and voltage used during
the previous session, with the weld data feature. To use the feature, press buttons P4 and P5
simultaneously.
3.3.9 Selection of control panel
Button P10 allows you to switch control between the control panels in the power source and
wire feeder. The indicator shows which of the control panels is in use.
• When the ‘LOCAL’ light is on, the wire feeding speed and welding current are set using
knobs P8 and P9 of the power source control panel.
• When the ‘REMOTE’ light is on, the wire feed speed and welding current are set using the
control panel of the wire feeder. Control knobs of the power source are disabled in this
mode.
3.3.10 Setting of the MIG operating mode
Button P7 allows you to set the MIG welding gun to either two-sequence or four-sequence
mode. The indicator shows the mode selected.
• In two-sequence mode (2T), welding is started by pressing the gun switch and stopped
by releasing the switch.
• In four-sequence mode (4T), the following actions take place:
1. When you press the gun switch, the shielding gas starts to ow.
2. When you release the switch, welding starts.
3. When you press the switch again, welding ends.
4. When you release the switch again, the ow of the shielding gas ends.
3.3.11 Setting of operation parameters
Button P7 also is used for changing welding parameters as follows:
• Depress button P7 for at least ve seconds. The set-up menu appears on display P2.
• Select the parameter to adjust with the left-hand knob (P8) so that the name of the
parameter you want to adjust is shown on display P2.
• Set a value for the parameter by using the right-hand knob (P9) such that the value you
want is shown on display P2. The value you selected is recorded in the control panel
memory.
• Exit the set-up menu by pressing button P7 again and holding for at least ve seconds or
by briey pressing the control panel start button (P1).
9
© Kemppi Oy / 1152
Page 12
EN
The table below lists the operation parameters and their possible values.
Name of
parameter
Name
displayed
Parameter
values
Factory
values
Description
Pre Gas Time
PrG 0.0 – 9.9 s 0.1 s Pre-welding gas time in seconds
Post Gas Time
PoG Aut, 0.1 – 32.0 s Aut Post-welding gas time in seconds or
automatically according to welding
current 1 s / 100 A (Aut)
Creep Start Level
CrE 10 – 170 % 50 % Initial wire feeding speed as a
percentage of the pre-set value:
10% = slowed start
100% = no creep start
170% = rush start
Start power
StA -9 ... +9 0 Strength of initial pulse
Post Current Time
PoC -9 ... +9 0 Post-welding current time
Remote Switch
rS 2t4, Inc 2t4 Selection of wire feed device switch
operation
Calibration Menu
CAL – – –, Ent – – – Wire feed speed calibration (see
instructions in sub-section 3.3.12)
LongSystem
Mode
LSy on, OFF OFF Select ‘ON’ if you are using long (>40
m) connector cables
Restore Factory
Settings
FAC OFF, PAn, All OFF Restore factory settings; exit the
menu by selecting ’All’
Water Cooler
COO on, OFF on Enables water cooler
Wire Inc Stop
Inc on, OFF OFF Safety function. Stops wire inch in
case arc does not ignite.
3.3.12 Calibration of the wire feed speed
When factory settings are used, the wire feed speed can be adjusted to between 4 and 100
without a unit of measurement. Only the LED symbol indicates that wire feed speed is the
parameter to be set.
The unit of the wire feed speed (m/min) is shown once the wire feed speed of the device has
been calibrated. To programmatically calibrate the wire feed speed:
1. To prepare the welding equipment for calibrating, do the following:
• Connect the wire feeder to the power source with the control cable.
• Insert the ller wire in the gun, and run the wire out of the contact tip.
• Adjust the feeder wheels so that they are suciently tight.
• Start the power source and turn on the control panel with the start button, P1.
2. Depress button P7 (SETUP) for at least ve seconds. The set-up menu appears on the
display.
3. Select the calibration menu (CAL) by rotating the left-hand knob, and then select the
value ’Enter’ (Ent) with the right-hand knob. Accept your selection by pressing button
P10 (REMOTE/LOCAL) briey.
4. Use the right-hand knob to select ‘m/min’ as the value of measure for the quantity to be
calibrated, and accept your selection by briey pressing button P10 (REMOTE/LOCAL).
5. Use the left-hand knob to set the lower calibration point to the desired value (e.g., 2.0 m/
min).
6. Cut the ller wire at the contact tip end. Press the trigger, and let the wire run until it
stops automatically. If the wire is not moving when calibrating the lower point, increase
the wire feed speed value, e.g. to 4.0m/min.
7. Measure the length of the loose wire end to an accuracy of 1 cm.
8. Enter the measurement with the right-hand knob, and accept your selection by pressing
button P10 (REMOTE/LOCAL) briey.
9. Use the left-hand knob to set the higher calibration point to an appropriate value (e.g.,
FastMig 300, 400, 500
10
Page 13
EN
18.0 m/min).
10. Repeat steps 6 – 8 for this higher calibration point.
11. The message ‘Suc cES’ appears on the display to indicate that calibration has ended
successfully. At the same time, the device exits calibration mode and returns to basic
operation mode.
12. In order to increase the accuracy of the calibration, calibration process should be done
twice. Therefore, repeat steps 2 – 11 and then device is ready for welding.
4. TROUBLESHOOTING
In the event of a failure of the machine, contact an authorised Kemppi service agent. Before
taking your unit for servicing, check the list below.
4.1 Overload (yellow indicator lit)
Two simultaneously operating fans cool the power source. The machine may, however,
overheat if continuously loaded above the rated values or if the circulation of cooling air is
prevented.
The yellow indicator (A10) is lit in the event of overheating. You then need to stop welding and
let the machine cool down. The indicator light turns o when welding can be resumed.
4.2 Control cable connector fuse
The rear wall of the power source contains fuse A9, which protects the control cable
connector, A7. Using an incorrect fuse may cause damage to the power source. It is important
that you always use the right kind of fuse. The type and size of the fuse are indicated next to
the fuse socket.
4.3 Electric network overvoltage or undervoltage
If the power source is used in an electric network with insucient voltage (less than 300 V),
the control features of the device are disabled automatically.
The primary circuits of the power source are protected against power spikes. The product’s
mains voltage range is broad enough to prevent overvoltage problems at up to 440 V (see
Section 8, ‘Technical specications’). Make sure that the voltage remains within the allowed
range, especially if the operating power is supplied by a generator set.
4.4 Missing phase in the electric network
If a phase is missing from the mains current, the welding features will be adversely aected or
the machine may have problems starting. Loss of a phase can be caused by a:
• Blown mains fuse.
• Damaged mains cable.
• Poor mains cable connection in the machine’s terminal block or mains socket.
11
© Kemppi Oy / 1152
Page 14
EN
4.5 Machine error codes
The machine always checks its operation automatically during start-up and reports any
failures detected. If failures are detected during start-up, they are shown as error codes on the
control panel display.
Power source error codes
Err3 Power source overvoltage
The machine has stopped the welding because it has detected momentary voltage spikes or
continuous overvoltage dangerous to the machine in the electric network. Check the quality
of the supply network.
Err4 Power source overheating
The power source has overheated. The cause may be one of the following:
1. The power source has been used for a long time at maximum power.
2. The circulation of cooling air to the power source is blocked.
3. The cooling system has experienced a failure.
Remove any obstacle to air circulation, and wait until the power source fan has cooled down
the machine.
Err5 Water unit alarm
The water circulation is blocked. The cause may be one of the following:
1. Congestion or disconnection in the cooling pipeline.
2. Insucient cooling liquid.
3. Excessive cooling liquid temperature.
Check the circulation of the cooling liquid and the air circulation of the water unit.
Err23 Power source overvoltage warning
The power source has detected voltage spikes in the electric network. Short power spikes
can be managed. They do not lead to interruptions in welding but may decrease the welding
quality. Check the quality of the supply network.
Err61 The water unit is not found
The water unit is not connected to the equipment, or the connection has failed.
Set the machine to gas cooling (3.3.7) if you are using a gas-cooled welding gun, or connect a
water unit.
Err154 Overloading of the wire feed motor
The welding has been interrupted because the wire feeding engine power has risen to a high
level. The cause may be congestion in the wire line. Check the wire lead, contact tip, and feed
rollers.
Err155 Warning of the wire feed unit overheating
The voltage level of the wire feeding engine has increased. The cause may be a stained wire
lead or a gun cable that is twisted at a sharp angle. Check the state of the gun, and clean the
wire line if this is necessary.
Err201 Use of PMT gun is prevented
The machine is intended for use with MMT guns. When a PMT gun is used, the gun’s jumpers
must be set to ‘FU’. This error code may appear also if the contacts of the gun trigger are
stained or there are problems with the trigger leads. Check the trigger’s leads.
Other error codes:
The machine can show codes not listed here. In the event of an unlisted code appearing,
contact an authorised Kemppi service agent and report the error code shown.
FastMig 300, 400, 500
12
Page 15
EN
5. MAINTENANCE
The utilisation level of the power source and its working environment should be taken into
consideration in planning the frequency of maintenance of the machine. Appropriate use and
preventive maintenance guarantee the trouble-freest use of the equipment. This allows you to
avoid interruptions in use and increases the productivity of the machine.
5.1 Cables
Check the condition of welding and mains cables daily. Do not use damaged cables. Also
make sure that all extension cables used in the mains connection are in proper condition and
compliant with regulations.
NOTE! The mains cables may be repaired and installed only by electrical contractors and installers
authorised to perform such operations.
5.2 Power source
Before cleaning the interior of the machine, you need to remove the case by unscrewing the
mounting screws at the top and sides of the machine.
NOTE! To prevent damage, wait approximately two minutes after disconnecting the mains cable
before removing the machine’s case.
Perform the following cleaning and maintenance at least every six months:
1. Clean the interior of the machine and the fan grill’s net of any dust and stains – for
example, with a soft brush and vacuum cleaner.
• Do not use pressurised air. The stain may become compressed into the grooves of the
coolers.
• Do not use a pressure-washing device.
2. Check the electrical connections of the machine. Clean any oxidised connections, and
tighten the loosened ones.
• Check for the right tension before you start repairing the connections.
NOTE! Remember that the machine may be repaired only by an electrical contractor or installer
authorised to perform such operations.
5.3 Regular maintenance
Authorised Kemppi service agents perform regular maintenance by agreement.
Tasks included in regular maintenance:
• Cleaning of equipment.
• Inspection and maintenance of the welding gun.
• Checking of connectors, switches, and control knobs.
• Checking of electrical connections.
• Checking of the mains cable and plug.
• Replacement of damaged or worn parts.
• Calibration testing, with adjustment of the functions and operational values of the
machine, if necessary.
13
© Kemppi Oy / 1152
Page 16
EN
6. DISPOSAL OF THE MACHINE
Do not dispose of electrical equipment with normal waste!
In observance of European Directive 2002/96/EC on waste electrical and electronic
equipment, and its implementation in accordance with national law, electrical equipment
that has reached the end of its life must be collected separately and taken to an appropriate
environmentally responsible recycling facility.
The owner of the equipment is obliged to deliver a decommissioned unit to a regional
collection centre, per the instructions of local authorities or a Kemppi representative. By
applying this European Directive you will improve the environment and human health.
7. ORDERING NUMBERS
Item Size Part number
FastMig™ KM 300 6033000
FastMig™ KM 400 6034000
FastMig™ KM 500 6035000
Earthing cable 5 m, 50 mm² 6184511
Earthing cable 5 m, 70 mm² 6184711
Cooling unit Fastcool 10 6068100
Transport unit PM500 6185291
Gun holder GH 30 6256030
8. TECHNICAL SPECIFICATIONS
FastMig 300, 400, 500
14
Page 17
EN
FastMig™ KM 300 KM 400 KM 500
Connection voltage, 3~50/60 Hz
400 V, -15 ... +20% 400 V, -15 ... +20% 400 V, -15 ... +20%
Rated power
60 % ED - - 25.9 kVA
80 % ED - 18.5 kVA -
100% ED 12.9 kVA 16.9 kVA 20.1 kVA
Connection cable
HO7RN-F 4G6 (5 m) HO7RN-F 4G6 (5 m) HO7RN-F 4G6 (5 m)
Fuse (delayed)
25 A 35 A 35 A
Output 40 °C
60 % ED - - 500 A
80 % ED - 400 A -
100% ED 300 A 380 A 430 A
Max. welding voltage
48 V 48 V 48 V
Open circuit voltage
65 V 65 V 65 V
Idle power
25 W 25 W 25 W
Efficiency at max. current
87 % 87 % 87 %
Power factor at max. current
0.9 0.9 0.9
Storage temperature range
-40 ... +60 °C -40 ... +60 °C -40 ... +60 °C
Operating temperature range
-20 ... 40 °C -20 ... 40 °C -20 ... 40 °C
Degree of protection
IP23S IP23S IP23S
EMC class
A A A
Minimun short circuit power Ssc of supply
network*
- 4.7 MVA 4.6 MVA
External dimensions
Length 590 mm 590 mm 590 mm
Width 230 mm 230 mm 230 mm
Height 430 mm 430 mm 430 mm
Weight
34 kg 35 kg 36 kg
Operating voltage
400 V, -15 ... +20% 400 V, -1 ... +20% 400 V, -15 ... +20%
Voltage supply for cooling unit
1~ 400 V AC 1~ 400 V AC 1~ 400 V AC
* See paragraph 2.2.
15
© Kemppi Oy / 1152
Page 18
www.kemppi.com
KEMPPI OY
Kempinkatu 1
PL 13
FIN-15801 LAHTI
FINLAND
Tel +358 3 899 11
Telefax +358 3 899 428
export@kemppi.com
www.kemppi.com
Kotimaan myynti:
Tel +358 3 899 11
Telefax +358 3 734 8398
myynti.@kemppi.com
KEMPPI SVERIGE AB
Box 717
S-194 27 UPPLANDS VÄSBY
SVERIGE
Tel +46 8 590 783 00
Telefax +46 8 590 823 94
sales.se@kemppi.com
KEMPPI NORGE A/S
Postboks 2151, Postterminalen
N-3103 TØNSBERG
NORGE
Tel +47 33 346000
Telefax +47 33 346010
sales.no@kemppi.com
KEMPPI DANMARK A/S
Literbuen 11
DK-2740 SKOVLUNDE
DANMARK
Tel +45 4494 1677
Telefax +45 4494 1536
sales.dk@kemppi.com
KEMPPI BENELUX B.V.
Postbus 5603
NL-4801 EA BREDA
NEDERLAND
Tel +31 765717750
Telefax +31 765716345
sales.nl@kemppi.com
KEMPPI (UK) Ltd
Martti Kemppi Building
Fraser Road
Priory Business Park
BEDFORD, MK44 3WH
UNITED KINGDOM
Tel +44 (0)845 6444201
Telefax +44 (0)845 6444202
sales.uk@kemppi.com
KEMPPI FRANCE S.A.S.
65 Avenue de la Couronne des Prés
78681 EPONE CEDEX
FRANCE
Tel +33 1 30 90 04 40
Telefax +33 1 30 90 04 45
sales.fr@kemppi.com
KEMPPI GmbH
Otto-Hahn-Straße 14
D-35510 BUTZBACH
DEUTSCHLAND
Tel +49 6033 88 020
Telefax +49 6033 72 528
sales.de@kemppi.com
KEMPPI SPÓŁKA Z O.O.
Ul. Borzymowska 32
03-565 WARSZAWA
POLAND
Tel +48 22 7816162
Telefax +48 22 7816505
info.pl@kemppi.com
KEMPPI AUSTRALIA PTY LTD.
13 Cullen Place
P.O. Box 5256, Greystanes NSW 2145
SMITHFIELD NSW 2164
AUSTRALIA
Tel. +61 2 9605 9500
Telefax +61 2 9605 5999
info.au@kemppi.com
OOO KEMPPI
Polkovaya str. 1, Building 6
127018 MOSCOW
RUSSIA
Tel +7 495 739 4304
Telefax +7 495 739 4305
info.ru@kemppi.com
ООО КЕМППИ
ул. Полковая 1, строение 6
127018 Москва
Tel +7 495 739 4304
Telefax +7 495 739 4305
info.ru@kemppi.com
KEMPPI, TRADING (BEIJING) COMPANY,
LIMITED
Room 420, 3 Zone, Building B,
No.12 Hongda North Street,
Beijing Economic Development Zone,
100176 Beijing
CHINA
Tel +86-10-6787 6064
+86-10-6787 1282
Telefax +86-10-6787 5259
sales.cn@kemppi.com
肯倍贸易（北京）有限公司
中国北京经济技术开发区宏达北路12号
创新大厦B座三区420室 (100176)
电话： +86-10-6787 6064
+86-10-6787 1282
传真： +86-10-6787 5259
sales.cn@kemppi.com
KEMPPI INDIA PVT LTD
LAKSHMI TOWERS
New No. 2/770,
First Main Road,
Kazura Garden,
Neelankarai,
CHENNAI - 600 041
TAMIL NADU
Tel +91-44-4567 1200
Telefax +91-44-4567 1234
sales.india@kemppi.com
1903310
1152
Loading...