Keithley DAQ6510, DMM6500 Quick Start Manual

Model DAQ6510 Quick Start Guide

Safety precautions

The following safety precautions should be observed before using this
product and any associated instrumentation. Although some instruments
and accessories would normally be used with nonhazardous voltages, there
are situations where hazardous conditions may be present.

This product is intended for use by personnel who recognize shock hazards
and are familiar with the safety precautions required to avoid possible injury .
Read and follow all installation, operation, and maintenance information
carefully before using the product. Refer to the user documentation for
complete product specifi cations.

If the product is used in a manner not specifi ed, the protection provided by
the product warranty may be impaired.

The types of product users are:

Responsible body

is the individual or group responsible for the use and
maintenance of equipment, for ensuring that the equipment is operated
within its specifi cations and operating limits, and for ensuring that operators
are adequately trained.

Operators

use the product for its intended function. They must be trained in
electrical safety procedures and proper use of the instrument. They must be
protected from electric shock and contact with hazardous live circuits.

Maintenance personnel

perform routine procedures on the product to
keep it operating properly , for example, setting the line voltage or replacing
consumable materials. Maintenance procedures are described in the user
documentation. The procedures explicitly state if the operator may perform
them. Otherwise, they should be performed only by service personnel.

Service personnel

are trained to work on live circuits, perform safe
installations, and repair products. Only properly trained service personnel
may perform installation and service procedures.

Keithley Instruments products are designed for use with electrical signals
that are measurement, control, and data I/O connections, with low transient
overvoltages, and must not be directly connected to mains voltage or to
voltage sources with high transient overvoltages. Measurement Category
II (as referenced in IEC 60664) connections require protection for high
transient overvoltages often associated with local AC mains connections.
Certain Keithley Instruments measuring instruments may be connected to
mains. These instruments will be marked as category II or higher.

Unless explicitly allowed in the specifi cations, operating manual, and
instrument labels, do not connect any instrument to mains.

Exercise extreme caution when a shock hazard is present. Lethal voltage
may be present on cable connector jacks or test fi xtures. The American
National Standards Institute (ANSI) states that a shock hazard exists when
voltage levels greater than 30 V

RMS

, 42.4 V

PEAK

, or 60 VDC are present. A
good safety practice is to expect that hazardous voltage is present in any
unknown circuit before measuring.

Operators of this product must be protected from electric shock at all times.
The responsible body must ensure that operators are prevented access
and/or insulated from every connection point. In some cases, connections
must be exposed to potential human contact. Product operators in these
circumstances must be trained to protect themselves from the risk of
electric shock. If the circuit is capable of operating at or above 1000 V, no
conductive part of the circuit may be exposed.

Do not connect switching cards directly to unlimited power circuits. They
are intended to be used with impedance-limited sources. NEVER connect
switching cards directly to AC mains. When connecting sources to switching
cards, install protective devices to limit fault current and voltage to the card.

Before operating an instrument, ensure that the line cord is connected to
a properly-grounded power receptacle. Inspect the connecting cables, test
leads, and jumpers for possible wear, cracks, or breaks before each use.

When installing equipment where access to the main power cord is
restricted, such as rack mounting, a separate main input power disconnect
device must be provided in close proximity to the equipment and within easy
reach of the operator.

For maximum safety , do not touch the product, test cables, or any other
instruments while power is applied to the circuit under test. ALWAYS remove
power from the entire test system and discharge any capacitors before:
connecting or disconnecting cables or jumpers, installing or removing
switching cards, or making internal changes, such as installing or removing
jumpers.

Do not touch any object that could provide a current path to the common
side of the circuit under test or power line (earth) ground. Always make
measurements with dry hands while standing on a dry , insulated surface
capable of withstanding the voltage being measured.

For safety , instruments and accessories must be used in accordance with
the operating instructions. If the instruments or accessories are used in a
manner not specifi ed in the operating instructions, the protection provided
by the equipment may be impaired.

Do not exceed the maximum signal levels of the instruments and
accessories. Maximum signal levels are defi ned in the specifi cations and
operating information and shown on the instrument panels, test fi xture
panels, and switching cards.

When fuses are used in a product, replace with the same type and rating for
continued protection against fi re hazard.

Chassis connections must only be used as shield connections for
measuring circuits, NOT as protective earth (safety ground) connections.

If you are using a test fi xture, keep the lid closed while power is applied to the
device under test. Safe operation requires the use of a lid interlock.

If a screw is present, connect it to protective earth (safety ground)
using the wire recommended in the user documentation.

The symbol on an instrument means risk of hazard. The user
must refer to the operating instructions located in the user
documentation in all cases where the symbol is marked on
the instrument.

The symbol on an instrument means warning, risk of electric
shock. Use standard safety precautions to avoid personal contact
with these voltages.

The symbol on an instrument shows that the surface may be hot.
Avoid personal contact to prevent burns.

The symbol indicates a connection terminal to the equipment
frame.

If this symbol is on a product, it indicates that mercury is present
in the display lamp. Please note that the lamp must be properly
disposed of according to federal, state, and local laws.

The WARNING heading explains hazards that may
result in injury , damage, or death.

Such damage

may invalidate the warranty.

The CAUTION heading explains hazards that may
cause minor injury or damage to the instrument.
Such damage may invalidate the warranty .

The CAUTION heading explains hazards that
may damage the instrument. Such damage may

invalidate the warranty .
Instrumentation and accessories shall not be connected to humans.
Before performing any maintenance, disconnect the line cord and all test

cables.
To maintain protection from electric shock and fi re, replacement

components in mains circuits—including the power transformer, test leads,
and input jacks—must be purchased from Keithley Instruments. Standard
fuses with applicable national safety approvals may be used if the rating
and type are the same. The detachable mains power cord provided with
the instrument may only be replaced with a similarly rated power cord.
Other components that are not safety-related may be purchased from
other suppliers as long as they are equivalent to the original component
(note that selected parts should be purchased only through Keithley
Instruments to maintain accuracy and functionality of the product). If you
are unsure about the applicability of a replacement component, call a
Keithley Instruments offi ce for information.

Unless otherwise noted in product-specifi c literature, Keithley Instruments
are designed to operate indoors only , in the following environment: Altitude

at or below 2,000 m (6,562 ft); temperature 0 °C to 50 °C (32 °F to 122 °F) ;
and pollution degree 1 or 2.

To clean an instrument, use a cloth dampened with deionized water or mild,
water-based cleaner. Clean the exterior of the instrument only. Do not apply
cleaner directly to the instrument or allow liquids to enter or spill on the
instrument. Products that consist of a circuit board with no case or chassis
(e.g., a data acquisition board for installation into a computer) should never
require cleaning if handled according to instructions. If the board becomes
contaminated and operation is affected, the board should be returned to the
factory for proper cleaning/servicing.

Safety precaution revision as of June 2017.

Power and envrionmental specifi cations

For indoor use only .

Power supply

100 V

RMS

to 240 V

RMS

, 50 Hz to 60 Hz

Maximum VA

50 V A

Operating altitude

Maximum 2000 m (6562 ft) above sea level

Operating
temperature

0 °C to 50 °C, 80% relative humidity at 35 °C

Storage temperature

-40 °C to 70 °C

Pollution degree

2

Contact information

If you have any questions after you review the information in
this documentation, please contact your local Keithley
Instruments offi ce, sales partner, or distributor. You can also
call the corporate headquarters of Keithley Instruments (toll-free
inside the U.S. and Canada only) at 1-800-935-5595, or from
outside the U.S. at [phone]. For worldwide contact
numbers, visit

www.tek.com/keithley.

Introduction

Thank you for choosing a Keithley Instruments product. The
DAQ6510 is a 6½ digit graphical sampling data-acquisition
system that provides high-speed digitizing and a large graphical
color touchscreen display. This DAQ offers a broad range of
measurement capabilities, including 15 measurement functions.
In addition to industry-leading DC accuracies, functions such
as capacitance, and 16-bit current and voltage digitizing are
included. Tying all these features together is a large 5-inch
color touchscreen display that brings users an unprecedented
combination of data visualization and interaction, enabling users
to gain deeper insight into their measurements.

The DAQ6510 provides superior measurement accuracy and the
speed necessary for a broad range of applications, from system
applications and production testing to benchtop applications.
The DAQ6510 meets application requirements for production
engineers, research and development engineers, test engineers,
and scientists.

This guide provides quick steps to set up and use the DAQ6510.

To change the fuse orientation:

1. Make sure the POWER is off.

2. Remove all test leads connected to the instrument.

3. Remove the power cord.

4. Squeeze the tabs on the fuse case and remove the fuse case

from the power module.

5. Remove the fuse from the fuse case.

6. Rotate the fuse so the proper voltage on the fuse shows in

the fuse case when installed.

7. Install the fuse case in the power module.

Unpack and inspect the instrument

To unpack and inspect the instrument:

1. Inspect the box for damage.

2. Open the box.

3. Remove the bag that contains the documentation,

standard accessories, and optional accessories.

4. Remove the DAQ6510 from the box.

5. Remove the packaging insert.

6. Inspect the instrument for any obvious signs of

physical damage. Report any damage to the shipping
agent immediately.

You should have received the DAQ6510 with:

• Software and Documentation Downloads insert

• Power line cord

• USB Type B cable

• 1757 Standard Test Lead Kit

• Calibration certifi cate

Refer to the packing list for additional items that might have
shipped with your instrument.

Check fuse settings

The fuse is set at the factory. Check the power module on the
back of the instrument. The correct voltage setting should be
displayed.