Kawasaki 691204 User Manual
COMPONENT
#691204
14" CUT-OFF SAW
INSTRUCTION MANUAL
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
PARA EL SERVICIO
PARA EL CONSUMIDOR
1-800-590-3723
Printed in China
KAWASAKI™IS A TRADEMARK LICENSED BY KAWASAKI™
MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
©COPYRIGHT 2007 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
691204 – 14" Cut-off Saw_Rev. 1/30/07
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS.FAILURE TO DO
SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE
DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION
AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE
A SUGGESTION OR COMMENT, GIVE US A CALL OR EMAIL US AT: INFO@ALLTRADETOOLS.COM.
YOUR FEEDBACK IS VITAL TO US.
87-1904-60957
SSEECCTTIIOONN FFIIVVEE
3 YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-30
CCOONNGGRRAATTUULLAATTIIOONNSS!!
Thanks for choosing this product. At Alltrade, our aim is to provide you with quality
products at an affordable price, and we want you to be totally satisfied with your
product and our Customer Service. If any help and advice is needed, please
contact us at 1-800-590-3723. Properly cared for, this product will give you many
years of satisfaction.
IINNTTEENNDDEEDD UUSSEE
This product is intended for consumer use only. This tool is not designed for professional use. The power cord should only be used in approved electrical outlets as
described in this manual. Failure to use the proper power cords and/or extension
cords may result in fire or possible damage to the bench grinder.
RREECCOOGGNNIIZZEE SSAAFFEETTYY SSYYMMBBOOLLSS,, WWOORRDDSS AANNDD LLAABBEELLSS
RREEAADD AANNDD UUNNDDEERRSSTTAANNDD AALLLL IINNSSTTRRUUCCTTIIOONNSS..
Failure to
follow all instructions in this manual may result severe personal injury or death.
Keep this manual and refer to it for Safety Instructions, Operating Procedures
and Warranty.
The safety instructions provided in this manual are not intended to cover all possible
conditions and practices that may occur when operating, maintaining and cleaning
power equipment.
Always use common sense and pay particular attention to all the
DDAANNGGEERR
,
WWAARRNNIINNGG, CCAAUUTTIIOONN
and
NNOOTTEE
statements of this manual.
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
DDAANNGGEERR
indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
WWAARRNNIINNGG
indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
TTAABBLLEE OOFF CCOONNTTEENNTTSS
CCOONNGGRRAATTUULLAATTIIOONNSS!!
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IINNTTEENNDDEEDD UUSSEE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SSEECCTTIIOONN OONNEE
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . . . . . . . 2-3
IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SSEECCTTIIOONN TTWWOO
GENERAL SAFETY RULES – FOR ALL ELECTRIC POWER TOOLS . . . . 4-5
GROUNDING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
EXTENSION CORD USAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
IMPORTANT SAFETY RULES FOR CUT-OFF SAWS . . . . . . . . . . . . . . . . 7-10
SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SSEECCTTIIOONN TTHHRREEEE
FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-18
UNLOCKING THE CUT-OFF SAW . . . . . . . . . . . . . . . . . . . . . . . . . . 13
REMOVING AND INSTALLING THE ABRASIVE CUTTING WHEEL . 14-15
ADJUSTING THE WORK VISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16
USING THE QUICK LOCK LEVER . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ATTACHING THE VICE HANDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ATTACHING THE REAR SPARK SHIELD . . . . . . . . . . . . . . . . . . . . . 18
OPERATING INSTRUCTIONS FOR THE CUT-OFF SAW . . . . . . . . . . . . . 18-20
SECURING THE TRIGGER SWITCH . . . . . . . . . . . . . . . . . . . . . . . . 18-19
USING THE CUT-OFF SAW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-20
SETTING THE CUT-OFF WHEEL DEPTH GAUGE. . . . . . . . . . . . . . . 20
LASER GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-22
OPERATING THE LASER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
LASER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SSEECCTTIIOONN FFOOUURR
MAINTENANCE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-24
TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS . . . . . . . . . . . . . . 27
1 2
GGEENNEERRAALL SSAAFFEETTYY RRUULLEESS –– FFOORR AALLLL EELLEECCTTRRIICC PPOOWWEERR TTOOOOLLSS
RREEAADD AANNDD UUNNDDEERRSSTTAANNDD AALLLL IINNSSTTRRUUCCTTIIOONNSS..
Failure to follow all instructions listed below may result in electric shock, fire and/or
serious personal injury.
KKEEEEPP GGUUAARRDDSS IINN PPLLAACCEE AANNDD IINN WWOORRKKIINNGG OORRDDEERR..
RREEMMOOVVEE AADDJJUUSSTTIINNGG K
KEEYYSS AANNDD WWRREENNCCHHEESS..
Form a habit of checking to see
that keys and adjusting wrenches are removed from the tool before turning it on.
KKEEEEPP WWOORRKK AARREEAA CCLLEEAANN..
Cluttered areas and benches invite accidents.
DDOO NNOOTT UUSSEE TTOOOOLL IINN AA DDAANNGGEERROOUUSS EENNVVIIRROONNMMEENNTT..
Do not use power tools
in damp or wet locations, or expose them to rain. Keep work area well lit.
KKEEEEPP CCHHIILLDDR
REENN AAWWAAYY..
All visitors should be kept a safe distance from the
work area.
MMAAKKEE YYOOUURR WWOORRKKSSHHOOPP CCHHIILLDD PPRROOOOFF,, WWIITTHH PPAADDLLOOCCKKSS,, MMAASSTTEERR
SSWWIITTCCHHEESS,, OORR BBYY RREEMMOOVVIINNGG SSTTAARRTTEERR KKE
EYYSS..
DDOO NNOOTT FFOORRCCEE TTOOOOLL..
The correct tool will do the job better and safer at the
rate for which it is designed.
UUSSEE TTHHEE CCOORRRREECCTT TTOOOOLL FFOORR YYOOUURR AAPPPPLLIICCAATTIIOONN..
Do not force tool or
attachment to do a job for which it was not designed.
AALLWWAAYYSS UUSSEE SSAAFFEETTYY GGLLAASSSSEESS..
Also use a face mask or dusk mask if cutting
operation is dusty. Everyday eyeglasses only have impact lenses, they are
NN
OOTT
safety glasses.
WWEEAARR PPRROOPPEERR AAPPPPAARREELL..
Do not wear loose clothing, gloves, neckties, rings,
bracelets, or other jewelry which may get caught in moving parts. Nonslip
footwear is recommended. Wear protective hair covering to contain long hair.
SSEECCUURREE WWOORRKK..
Use clamps or other practical ways to secure and support the
workpiece to a stable platform. Holding the work by hand or against your body
is unstable and may lead to loss of control.
DDOO NNOOTT OOVVEERRRREEAACCHH..
Keep proper footing and balance at all times. Proper
footing and balance enables better control of the power tool in unexpected situations.
MMAAIINNTTAAIINN TTOOOOLLSS WWIITTHH CCAARREE..
Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing accessories.
DDIISSCCOONNNNEECCTT
TTOOOOLLSS BBEEFFOORREE SSEERRVVIICCIINNGG AANNDD WWHHEENN CCHHAANNGGIINNGG AACCCCEESS--
SSOORRIIEESS,, SSUUCCHH AASS BBLLAADDEESS,, BBIITTSS,, CCUUTTTTEERRSS AANNDD TTHHEE LLIIKKEE..
R
REEDDUUCCEE TTHHEE RRIISSKK OOFF UUNNIINNTTEENNTTIIOONNAALL SSTTAARRTTIINNGG..
Be sure switch is in the
“OFF” position before plugging in.
43
CCAAUUTTIIOONN
indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
CCAAUUTTIIOONN
used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
NNOOTTEE
provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
IIMMPPOORRTTAANNTT SSAAFFEEGGUUAARRDDSS
PPeeooppllee wwiitthh eelleeccttrroonniicc ddeevviicceess,, ssuucchh aass ppaacceemmaakkeerrss,, sshhoouulldd ccoonnssuulltt tthheeiirr
pphhyyssiicciiaann((ss)) bbeeffoorree uussiinngg tth
hiiss pprroodduucctt.. OOppeerraattiioonn ooff eelleeccttrriiccaall eeqquuiippmmeenntt iinn
cclloossee pprrooxxiimmiittyy ttoo aa hheeaarrtt ppaacceemmaakkeerr ccoouulldd ccaauussee iin
ntteerrffeerreennccee oorr ffaaiilluurree ooff
tthhee ppaacceemmaakkeerr..
WWAARRNNIINNGG::
Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
WWAARRNNIINNGG::
Handling the power cord on corded products may expose you to
lead, a chemical known to the State of California to cause cancer and birth
defects or other reproductive harm.
WWaasshh hhaannddss aafftteerr hhaannddlliinngg..
SSAAVVEE TTHHEESSEE IINNSSTTRRUUCCTTIIOONNSS FFOORR FFUUTTUURREE RREEFFEERREENNCCEE..
This Cut-off saw is equipped with a grounded 3-wire power cord with a 3-prong
plug. If the power cord will not fit into the wall plug, an approved adapter can be
used as long as it is connected to the center screw in the wall plate. See Figure 1
and the steps below to use an AC grounding adapter:
1.Remove the cover plate mounting screw.
2.Insert the AC grounding adapter into the bottom receptacle so the green
grounding lug fits over the screw hole.
3.Install the mounting screw back into the cover plate securely affixing the
adapter to the receptacle.
NNeevveerr mmooddiiffyy tthhee eelleeccttrriiccaall aaddaapptteerr bbyy ccuuttttiinngg ooffff tthhee
ggrroouunnddiinngg pprroonngg ssoo iitt wwiillll ffiitt iinnttoo uunna
apppprroovveedd,, uunn--ggrroouunnddeedd eelleeccttrriiccaall rreecceepp--
ttaacclleess.. FFaaiilluurree ttoo ffoollllooww tthhiiss pprroocceedduurree ccoouulldd rreessuulltt iinn bbuurrn
nss,, sseevveerree eelleeccttrrii--
ccaall sshhoocckk,, oorr eevveenn ddeeaatthh..
If you have questions about connecting the Cut-off saw, contact a certified
electrician to install the proper circuitry needed for this and other power tools
you use. Repair or replace any damaged electrical wiring
IIMMMMEEDDIIAATTEELLYY..
EEXXTTEENNSSIIOONN CCOORRDD UUSSAAGGEE
Extension cords are not recommended for use with this saw. Extension cords, if
used, must be properly grounded with a 3-prong plug on one and a 3-hole receptacle on the other.
DDOO NNOOTT uussee ggrroouunnddiinngg aaddaapptteerrss wwiitthh aann eexxtteennssiioonn ccoorrdd..
Extension cords must be UL listed and use a minimum of 18 A.W.G. wiring.
Extension cords should never exceed 25 feet in length. Extension cords, that are too
long, cause a voltage drop over the extra distance causing the saw motor to run
slower with the possibility of causing damage to the motor. Using extension cords
with smaller than the recommended wire gauge run the risk of getting too hot, melting, and/or causing fires. See table, “Extension Cord Specifications”, on page 26.
UUSSEE RREECCOOMMMMEENNDDEEDD AACCCCEESSSSOORRIIEESS..
Consult the owners manual for recommend-
ed accessories. The use of improper accessories may cause cause risk of injury.
NNEEVVEERR SSTTAANNDD OONN TTOOOOLL..
Serious injury could occur if the tool is tipped or if
the cutting tool is unintentionally contacted.
CCHHEECCKK DDAAMMAAGGEEDD PPAARRTTSS..
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to determine that it will operate
properly and perform its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged
should be properly repaired or replaced.
DDIIRREECCTTIIOONN OOFF FFEEEEDD..
Only feed work into a blade or cutter against the direc-
tion of rotation of the blade or cutter.
GGRROOUUNNDDIINNGG IINNSSTTRRUUCCTTIIOONNSS
NNEEVVEERR uussee aapppplliiaanncceess oorr eeqquuiippmmeenntt tthhaatt hhaavvee mmoottoorrss
wwiitthh aauuttoommaattiicc rreesseett oovveerrllooaadd pprrootteeccttiivvee ddeevviicceess..
TThheessee pprrootteeccttiivvee ddeevviicceess
ccaann ccaauussee uunneexxppeecctteedd ssttaarrttuuppss tthhaatt ccaann ccaauussee pprrooppeerrttyy ddaammaaggee,, sseevveerree ppeerr--
ss
oonnaall iinnjjuurryy,, oorr ddeeaatthh..
The electrical power source for this Cut-off saw
MMUUSSTT
be grounded in order to
prevent possible electric shock or even death should the tool malfunction or break
down. Grounding provides a path of least resistance for electric current thus reducing the risk of electrical shock. The power source must also use a minimum 20A
service. Multiple power tools should never be used on the same circuit at the same
time.
FFaaiilluurree ttoo pprrooppeerrllyy ggrroouunndd tthhiiss CCuutt--ooffff ssaaww ccoouulldd rreessuulltt iinn
bbuurrnnss,, sseevve
erree eelleeccttrriiccaall sshhoocckk,, aanndd eevveenn ddeeaatthh.. TThhiiss iiss eessppeecciiaallllyy ttrruuee iiff uusseedd iinn
ddaammpp oorr wweett llooccaattiioonnss oorr nneea
arr mmeettaalllliicc pplluummbbiinngg.. TThhee rreeaaccttiioonn ffrroomm eelleeccttrriiccaall
sshhoocckk ccoouulldd ppoossssiibbllyy ccaauussee yyoouurr hhaannddss ttoo mmaakkee ccoonnt
taacctt wwiitthh tthhee ccuuttttiinngg ttoooollss..
NNoott aallll oouuttlleettss aarree pprrooppeerrllyy ggrroouunnddeedd,, rreeggaarrddlleessss ooff tthhee
ttyyppee ooff rreecceepptta
accllee tthheeyy hhaavvee.. IIff yyoouu aarree nnoott ssuurree iiff tthhee rreecceeppttaaccllee iiss pprrooppeerrllyy
ggrroouunnddeedd oorr nnoott,, ccoonnssuulltt aa cceerrttiiffiie
edd eelleeccttrriicciiaann.. TThhee AACC rreecceeppttaaccllee mmuusstt bbee
pprrootteecctteedd bbyy aa dduuaall eelleemmeenntt ttiimmee ddeellaayy oorr aa cciirrccuuiitt bbrreeaakkeer
r..
5
UNGROUNDED AC RECEPTACLE
GROUNDED RECEPTACLE
GROUNDING ADAPTER
CUT-OFF SAW POWER CORD
CUT-OFF SAW POWER CORD
COVERPLATE
MOUNTING SCREW
FIGURE 1. CONNECTING THE CUT-OFF SAW TO THE AC POWER RECEPTACLE
MMAAIINNTTAAIINN AA PPRROOPPEERR WWOORRKK EENNVVIIRROONNMMEENNTT..
Do not operate the Cut-off saw
in damp or wet locations or expose it to rain. Water can cause the electrical
components to malfunction resulting in damage to the Cut-off saw and/or serious injury or death to the operator.
DDOO NNOOTT PPEERRFFOORRMM AANNYY OOPPEERRAATTIIOONN FFRREEEEHHAANNDD..
AALLWWAAYYSS UUSSEE AAPPPPRROOVVEEDD TTAABBLLEE CCLLAAMMPPSS AANNDD VVIICCEESS
to clamp workpieces to
the Cut-off saw table to prevent breakage, damage to the Cut-off saw, the workpiece, and possible severe injury to the operator. Contact Alltrade Customer
Service at 1-800-590-3723 (toll free) for authorized accessories.
UUSSEE OONNLLYY AABBRRAASSIIVVEE CCUUTTTTIINNGG WWHHEEEELLSS
that are designed for the various
speeds of this Cut-off saw. The abrasive cutting wheels should have an arbor
size 5/8” OR SMALLER. Unsuitable cutting wheels can break without warning
throwing fragments outward at high speeds possibly causing severe injuries.
Contact Alltrade Customer Service at 1-800-590-3723 (toll free) for authorized
abrasive wheel specifications.
DDOONN’’TT FFOORRCCEE TTHHEE TTOOOOLL..
The Cut-off saw will do a better job and be safer if
cutting operations are performed at the proper speeds as expressed in this
manual.
AALLWWAAYYSS EEAASSEE TTHHEE CCUUT
TTTIINNGG WWHHEEEELL AAGGAAIINNSSTT TTHHEE WWOORRKKPPIIEECCEE
when starting a cutting operation. A sudden impact can cause the abrasive wheel to break
sending fragments flying away from the Cut-off saw at high speeds resulting in
possible severe injury to the operator.
DDOO NNOOTT UUSSEE AANN AABBRRAASSIIVVEE WWHHEEEELL TTHHAATT WWOOBBBBLLEESS OORR VVIIBBRRAATTEESS..
Visually
inspect the abrasive wheels before they contact the workpiece ensuring there
are no side-to-side movements. Should the abrasive wheel wobble from sideto-side or if the tip appears broken, replace them immediately. If the vibration
still exists, check the bearings and the motor shaft and repair or replace them
as soon as possible. EXCESSIVE VIBRATION can cause severe damage to both
the workpiece and the Cut-off saw.
AADDJJUUSSTT T
THHEE TTOOOOLL TTAABBLLEE BBEEFFOORREE EEAACCHH UUSSEE..
The tool table should be tightened and placed at the proper angle for the cutting job before the Cut-off saw
is put into use. If not properly adjusted, the workpiece can unexpectedly move
causing the abrasive wheel to seize resulting in damage to it or possible severe
injury to the operator.
DDOO NNOOTT SSTTAANNDD DDIIRREECCTTLLYY IINN FFRROONNTT OOFF TTHHEE CCUUTT--OOFFFF SSAAWW
when it is first
turned on. Loose fragments could fly off at high speeds possibly causing injury.
8
IIMMPPOORRTTAANNTT SSAAFFEETTYY RRUULLEESS FFOORR CCUUTT--OOFFFF SSAAWWSS
AAVVOOIIDD PPRROOLLOONNGGEEDD CCOONNTTAACCTT WWIITTHH DDUUSSTT ccrreeaatteedd bbyy tthhee aabbrraassiivvee CCuutt--ooffff
ssaaww.. AAlllloowwiinngg tthhee dduusstt ttoo ggeett iinnttoo
yyoouurr mmoouutthh,, eeyyeess,, oorr llaayy oonn yyoouurr sskkiinn pprroo--
mmootteess tthhee aabbssoorrppttiioonn ooff hhaarrmmffuull cchheemmiiccaallss iinnttoo yyoouurr bbooddyy.
.
RREEAADD AANNDD UUNNDDEERRSSTTAANNDD AALLLL IINNSSTTRRUUCCTTIIOONNSS.. IIff tthheerree aarree iinnssttrruuccttiioonnss iinn
tthhiiss mmaannuuaall tthhaatt aarree nnoott ccoommpplleet
teellyy uunnddeerrssttoooodd,, sseeeekk tthhee aaddvviiccee ooff aa ttrraaiinneedd
pprrooffeessssiioonnaall oorr ccoonnttaacctt AAllllttrraaddee CCuussttoommeerr SSeerrvviiccee aatt 11-
-880000--559900--33772233 bbeeffoorree
aatttteemmppttiinngg ttoo ppeerrffoorrmm tthhee pprroocceedduurreess.. FFaaiilluurree ttoo ffoollllooww aallll iinnssttrruuccttiioonnss lliisstt--
ee
dd iinn tthhiiss mmaannuuaall mmaayy rreessuulltt iinn pprrooppeerrttyy ddaammaaggee,, ddaammaaggee ttoo tthhee ttooooll,, oorr
sseerriioouuss ppeerrssoonnaall iinnjjuurryy oorr eev
veenn ddeeaatthh..
UUNNPPAACCKK TTHHEE CCUUTT--OOFFFF SSAAWW CCOOMMPPLLEETTEELLYY FFRROOMM IITTSS CCAARRTTOONN..
Inspect the
saw and accessories and ensure they are free from defects or breakage due to
shipping.
DDOO NNOOTT OOPPEERRAATTEE TTHHIISS CCUUTT--OOFFFF SSAAWW
until it is completely assembled according to the instructions in this manual. Failure to adhere to these instructions
could result in serious and/or permanent injury to the operator.
MMAAK
KEE SSUURREE AAPPPPRROOVVEEDD EEYYEE PPRROOTTEECCTTIIOONN IISS BBEEIINNGG WWOORRNN
and properly
adjusted and secured at all times the Cut-off saw is in use. Everyday
eyeglasses only have impact resistant lenses and ARE NOT safety glasses.
Safety glasses must conform to ANSI Z87.1 requirements. Approved safety
glasses and goggles will have Z87 printed or stamped on them.
FFOOLLLLOOWW AALLLL WWIIRRIINNGG CCOODDEESS..
Use only properly grounded three-hole grounded receptacles. DO NOT cut the third prong off the power cord. When using an
extension cord, use only UL Listed extension cords with minimum 16 AWG
wiring and a maximum length of 25 feet. See ELECTRICAL SAFETY section in
this manual.
KKEEEEPP BBYYSSTTAANNDDEERRSS,, CCHHIILLDDRREENN,
, AANNDD VVIISSIITTOORRSS
at a safe distance from the
Cut-off saw while it is in operation. Distractions can cause inadvertent misuse
resulting in possible injury to the bystanders or to the operator.
WWEEAARR PPRROOPPEERR AAPPPPAARREELL..
Do not wear loose clothing, gloves, neckties, rings,
bracelets, or other apparel that could possibly become caught in the moving
parts of the Cut-off saw. When working in a shop environment around power
tools, wear nonslip footwear. Use protective hair covering to contain long hair.
KKEEEEPP TTHHEE WWOORRKK AARREEAA CCLLEEAANN AATT AALLLL TTIIMMEESS..
Cluttered areas around the Cutoff saw can cause unexpected accidents if the debris comes in contact with the
moving parts of the Cut-off saw.
7
Loading...