Page 1
Instructions for use
PHYSIO Evo/Evo F/One
Always be on the safe side.
Page 2
Distributed by:
KaVo Dental GmbH
Bismarckring 39
D-88400 Biberach
Phone +49 (0) 7351 56-0
Fax +49 (0) 7351 56-1488
Manufacturer:
Kaltenbach & Voigt GmbH
Bismarckring 39
D-88400 Biberach
www.kavo.com
Page 3
Instructions for use PHYSIO Evo/Evo F/One
Table of contents
Table of contents
1 User instructions............................................................................................................................................... 5
1.1 User guide................................................................................................................................................ 5
1.2 Abbreviations............................................................................................................................................ 5
1.3 Symbols.................................................................................................................................................... 5
1.4 Target group ............................................................................................................................................ 5
1.5 Service...................................................................................................................................................... 5
1.6 Terms and conditions of warranty............................................................................................................. 6
1.7 Transportation and storage....................................................................................................................... 6
1.7.1 Currently valid packaging regulations......................................................................................... 6
1.7.2 Damage in transit........................................................................................................................ 6
1.7.3 Information on the packaging: Storage and transportation......................................................... 7
2 Safety............................................................................................................................................................... 9
2.1 Description of safety instructions.............................................................................................................. 9
2.1.1 Warning symbol........................................................................................................................... 9
2.1.2 Structure...................................................................................................................................... 9
2.1.3 Description of hazardous steps................................................................................................... 9
2.2 Safety instructions.................................................................................................................................... 9
3 Description of the Product.............................................................................................................................. 11
3.1 Purpose – Intended use ......................................................................................................................... 11
3.2 Operator stool PHYSIO Evo/Evo F/One................................................................................................. 12
3.3 Rating plates and instruction labels........................................................................................................ 13
3.4 Technical specifications PHYSIO Evo.................................................................................................... 14
3.5 Technical specifications PHYSIO Evo F................................................................................................. 14
3.6 Technical specifications PHYSIO One................................................................................................... 15
4 Installation...................................................................................................................................................... 16
4.1 Packaging............................................................................................................................................... 16
4.1.1 Transportation and storage....................................................................................................... 16
4.1.2 Packed items............................................................................................................................. 16
4.2 Assembly of operator stool PHYSIO Evo/Evo F/One............................................................................. 17
4.2.1 Mounting the castors................................................................................................................. 17
4.2.2 Mounting the upholstery............................................................................................................ 18
4.2.3 Mounting the backrest upholstery............................................................................................. 19
4.2.4 Adjust the gas pressure spring.................................................................................................. 20
4.3 Assembly of operator stool PHYSIO Evo F............................................................................................ 21
4.3.1 Mounting the top part of the chair.............................................................................................. 21
4.3.2 Mounting the upholstery............................................................................................................ 22
4.3.3 Mounting the backrest cushion.................................................................................................. 22
4.3.4 Adjust the gas pressure spring foot control............................................................................... 23
5 Dismantling..................................................................................................................................................... 24
5.1 Dismantling the operator stool PHYSIO Evo/Evo F/One........................................................................ 24
5.2 Removing the intervention protection cover of the gas pressure spring................................................. 24
5.3 Dismantling the gas pressure spring...................................................................................................... 25
5.3.1 Dismantling the gas pressure spring Evo / One........................................................................ 25
5.3.2 Dismantling the gas pressure spring Evo F............................................................................... 27
6 Operation........................................................................................................................................................ 30
3 / 38
Page 4
Instructions for use PHYSIO Evo/Evo F/One
Table of contents
6.1 PHYSIO Evo........................................................................................................................................... 30
6.1.1 Adjust the seat height................................................................................................................ 30
6.1.2 Adjusting the seat...................................................................................................................... 30
6.1.3 Adjust the backrest angle.......................................................................................................... 31
6.2 PHYSIO Evo F........................................................................................................................................ 32
6.2.1 Adjust the seat height................................................................................................................ 32
6.2.2 Adjusting the seat...................................................................................................................... 32
6.2.3 Adjust the backrest angle.......................................................................................................... 33
6.3 PHYSIO One.......................................................................................................................................... 34
6.3.1 Adjust the seat height................................................................................................................ 34
6.3.2 Adjusting the seat and backrest................................................................................................ 34
7 Reprocessing methods according to DIN EN ISO 17664............................................................................... 35
7.1 General care instructions........................................................................................................................ 35
7.2 Cleaning and disinfection........................................................................................................................ 35
8 Troubleshooting.............................................................................................................................................. 36
4 / 38
Page 5
Instructions for use PHYSIO Evo/Evo F/One
1 User instructions | 1.1 User guide
1 User instructions
1.1 User guide
Requirement
Read these instructions before the initial startup to prevent misuse and damage.
1.2 Abbreviations
Abbre‐
viation
IfU Instructions for use
CI Care instructions
AI Assembly instructions
TI Technician's instructions
SC Safety checks
IEC International Electrotechnical Commission
RI Repair instructions
RK Retrofitting kit
AS Assembly set
EP Enclosed parts
EMC Electromagnetic compatibility
PI Processing instructions
Explanation
1.3 Symbols
See the Safety/Warning Symbols section
Important information for users and technicians
Action required
1.4 Target group
This document is for dentists, the dental office personnel, and the service technician.
1.5 Service
KaVo Customer Service:
+49 (0) 7351 56-1000
Service.Einrichtungen@kavo.com
Please refer to the serial number of the product in all inquiries!
For further information, please visit: www.kavo.com
5 / 38
Page 6
Instructions for use PHYSIO Evo/Evo F/One
1 User instructions | 1.6 Terms and conditions of warranty
1.6 Terms and conditions of warranty
KaVo provides the final customer with a warranty that the product cited in the hand‐
over certificate will function properly and guarantees zero defects in the material or
processing for a period of 12 months from the date of purchase, subject to the follow‐
ing conditions:
Upon justified complaints of flaws or a short delivery, KaVo will make good its warran‐
ty by replacing the product free of cost or repairing it according to the customer's wish‐
es. Other claims of any nature whatsoever, in particular with respect to compensation,
are excluded. In the event of default and gross negligence or intent, this shall only ap‐
ply in the absence of mandatory legal regulations to the contrary.
KaVo cannot be held liable for defects and their consequences due to natural wear,
improper cleaning or servicing, non-compliance with operating, servicing or connection
instructions, calcification or corrosion, contaminated air or water supplies or chemical
or electrical factors deemed abnormal or impermissible in accordance with factory
specifications.
The warranty does not usually cover bulbs, glassware, rubber parts and the colour‐
fastness of plastics.
Defects or their consequences that can be attributed to interventions on or changes
made to the product by the customer or a third party are excluded from the warranty.
Claims from this warranty can only be asserted when the transfer form (copy) belong‐
ing to the product has been sent to KaVo, and the original can be presented by the
operator or user.
1.7 Transportation and storage
1.7.1 Currently valid packaging regulations
Note
Only valid for the Federal Republic of Germany.
Dispose of and recycle the sales packaging appropriately in accordance with current
packaging regulations, employing waste management or recycling companies. Com‐
ply with the comprehensive return system. KaVo has had its sales packaging licensed
for this purpose. Please comply with the regional public waste-disposal system.
1.7.2 Damage in transit
In Germany
If the packaging is visibly damaged on delivery, please proceed as follows:
1. The recipient of the package must record the loss or damage on the delivery re‐
ceipt. The recipient and the representative of the shipping company must sign this
delivery receipt.
2. Leave the product and packaging in the condition in which you received it.
3. Do not use the product.
4. Report the damage to the shipping company.
5. Report the damage to KaVo.
6. Consult with KaVo first, before returning a damaged product.
7. Send the signed delivery receipt to KaVo.
6 / 38
Page 7
Instructions for use PHYSIO Evo/Evo F/One
1 User instructions | 1.7 Transportation and storage
If the product is damaged but there was no discernable damage to the packaging
upon delivery, proceed as follows:
1. Report the damage to the shipping company immediately and no later than 7 days
after delivery.
2. Report the damage to KaVo.
3. Leave the product and packaging in the condition in which you received it.
4. Do not use a damaged product.
Note
If the recipient fails to comply with any of the above-mentioned obligations, the
damage will be considered to have arisen after delivery
(in accordance with the General German Freight Forwarders´ Terms and Conditions, Art. 28)
.
Outside Germany
Note
KaVo shall not be held liable for damage arising from transportation.
The shipment must be checked on arrival.
If the packaging is visibly damaged on delivery, please proceed as follows:
1. The recipient of the package must record the loss or damage on the delivery re‐
ceipt. The recipient and the representative of the shipping company must sign this
delivery receipt.
Without this evidence, the recipient will not be able to assert a claim for damages
against the shipping company.
2. Leave the product and packaging in the condition in which you received it.
3. Do not use the product.
If the product is damaged but there was no discernable damage to the packaging
upon delivery, proceed as follows:
1. Report any damage to the shipping company either immediately or no later than 7
days after delivery.
2. Leave the product and packaging in the condition in which you received it.
3. Do not use a damaged product.
Note
If the recipient fails to comply with any of the above-mentioned obligations, the
damage will be considered to have arisen after delivery
(in accordance with CMR law, Chapter 5, Art. 30).
1.7.3 Information on the packaging: Storage and transportation
Note
Please keep the packaging in case you need to return the product for servicing or
repair.
The symbols printed on the outside are for transportation and storage, and have the
following meaning:
Transport upright with the arrows pointing upwards!
Fragile - protect against impact!
7 / 38
Page 8
Instructions for use PHYSIO Evo/Evo F/One
1 User instructions | 1.7 Transportation and storage
Protect from moisture!
Permissible stacking load
Temperature range
Humidity
Air pressure
8 / 38
Page 9
Instructions for use PHYSIO Evo/Evo F/One
2 Safety | 2.1 Description of safety instructions
2 Safety
2.1 Description of safety instructions
2.1.1 Warning symbol
Warning symbol
2.1.2 Structure
DANGER
The introduction describes the type and source of the hazard.
This section describes potential consequences of non-compliance.
▶ The optional step includes necessary measures for hazard prevention.
2.1.3 Description of hazardous steps
Safety instructions distinguishing between three hazard levels are used in this docu‐
ment to prevent personal and property damage.
CAUTION
CAUTION
indicates a hazardous situation that can cause damage to property or mild to moder‐
ate injuries.
WARNING
WARNING
indicates a hazardous situation that can lead to serious or fatal injury.
DANGER
DANGER
indicates a maximal hazard due to a situation that can directly cause death or fatal
injury.
2.2 Safety instructions
CAUTION
Damage from unsuitable accessories.
The use of accessories, other components, and cables other than those specified
(with the exception of components and cables sold by KaVo as spare parts for inter‐
nal components) can increase emissions or reduce the electromagnetic immunity of
the product.
▶ Use accessories recommended by KaVo only!
9 / 38
Page 10
Instructions for use PHYSIO Evo/Evo F/One
2 Safety | 2.2 Safety instructions
Damage due to working on the pressure vessel.
Forceful opening of the pressure vessel or extensive heat exposure can lead to injury
and damage.
▶ Only instructed specialists may work on or exchange parts in the vicinity of the
seat height adjusting element.
Screws are pre-tensioned.
Inappropriate loosening of screws on the support plate beneath the seat upholstery
can lead to injury and damage.
▶ Only instructed specialists may dismantle screws from the support plate.
CAUTION
CAUTION
10 / 38
Page 11
Instructions for use PHYSIO Evo/Evo F/One
3 Description of the Product | 3.1 Purpose – Intended use
3 Description of the Product
3.1 Purpose – Intended use
The PHYSIO Evo/Evo F/One is an operator stool for dentists in a dental practice in
accordance with DIN EN ISO 7493.
All versions of the PHYSIO Evo/Evo F/One operator stool are tested and approved in
accordance with the currently applicable guidelines.
All versions of the PHYSIO Evo/Evo F/One operator stool are compliant with DIN EN
1335 - 2 and 3, DIN 4550 and DIN EN ISO 7493.
Intended use also comprises the observation of all indications in the instructions for
used as well as adherence to prescribed inspections and maintenance.
Application of and compliance with the general guidelines and/or national laws, nation‐
al regulations, and the rules of technology applicable to this product for start-up and
use of the KaVo product for the intended purpose are to be applied and complied with.
The user must ensure that the unit works properly and is in satisfactory condition be‐
fore each use.
The applicable national legal regulations must be observed during the use of the de‐
vice, in particular the following:
▪ Current occupational safety regulations
▪ Current accident prevention regulations
Users have a duty to:
▪ Only use equipment that is operating correctly
▪ to protect himself, the patient and third parties from danger.
▪ to avoid contamination from the product
11 / 38
Page 12
Instructions for use PHYSIO Evo/Evo F/One
3 Description of the Product | 3.2 Operator stool PHYSIO Evo/Evo F/One
3.2 Operator stool PHYSIO Evo/Evo F/One
KaVo PHYSIO Evo/Evo F/One
The operator stool PHYSIO Evo/Evo F/One is equipped with soft castors Mat. no.
1.010.3896 for hard flooring upon delivery. The running surface and housing of the
castors are bi-chrome.
Hard castors for soft flooring, e.g. fitted carpet are available as a kit Mat. no.
1.010.3827. The running surface and housing of the castors are monochrome.
Note
Use the castors that are appropriate for the flooring.
Only use soft castors for hard flooring. Only use hard castors for soft flooring.
12 / 38
Page 13
Instructions for use PHYSIO Evo/Evo F/One
3
2
1
4
3
2
1
4
6
7
5
89
3
2
1
4
6
7
5
89
6
7
5
89
Acht ung : Aust ausch und Arbeite n im Bereich
des Sitzhöh enve rste lleleme nt es nu r durch
gesc hultes Personal!
Att en tion : Exchang e and work in the area of
th e gas spring only by tra ined pe rsonn el!
3 Description of the Product | 3.3 Rating plates and instruction labels
3.3 Rating plates and instruction labels
The rating plates are located underneath the stool.
KaVo PHYSIO Evo/Evo F/One rating plate
KaVo Logo
①
GS mark of conformity
③
HIBC Code
②
Read and take note of the content of
④
accompanying documents
GOST R certification
⑤
Year of manufacture - month - serial
⑦
Manufacturer
⑥
Material number
⑧
number
Device type
⑨
The information label is located beneath the stool, on the left beside the rating plate.
Information label PHYSIO Evo/Evo F/One
13 / 38
Page 14
Instructions for use PHYSIO Evo/Evo F/One
3 Description of the Product | 3.4 Technical specifications PHYSIO Evo
3.4 Technical specifications PHYSIO Evo
Lowest seat height, with load 465 mm
Highest seat height, without load 660 mm
Lowest seat height, loaded 460 mm
Highest seat height, loaded 630 mm
Seat height adjustment
range, without load
Seat width max. 400 mm
Seat depth 380 mm
Adjustment range of the
backrest inclination
Seat inclination 15 °
Height 1,000 mm
Width 600 mm
Weight 12.5 kg
Permissible load 150 kg
195 mm
30 °
3.5 Technical specifications PHYSIO Evo F
Lowest seat height, with load 475 mm
Highest seat height, without load 660 mm
Lowest seat height, loaded 470 mm
Highest seat height, loaded 630 mm
Seat height adjustment
range, without load
Seat width max. 400 mm
Seat depth 380 mm
Adjustment range of the
backrest inclination
Seat inclination 15 °
Height 1,000 mm
Width 600 mm
Weight 13 kg
Permissible load 150 kg
185 mm
30 °
14 / 38
Page 15
Instructions for use PHYSIO Evo/Evo F/One
3 Description of the Product | 3.6 Technical specifications PHYSIO One
3.6 Technical specifications PHYSIO One
Lowest seat height, with load 465 mm
Highest seat height, without load 660 mm
Lowest seat height, loaded 460 mm
Highest seat height, loaded 630 mm
Seat height adjustment
195 mm
range, without load
Seat width max. 400 mm
Seat depth 380 mm
Adjustment range of the
15 °
backrest inclination
Seat inclination 15 °
Height 1,000 mm
Width 600 mm
Weight 12 kg
Permissible load 150 kg
15 / 38
Page 16
Instructions for use PHYSIO Evo/Evo F/One
4 Installation | 4.1 Packaging
4 Installation
4.1 Packaging
4.1.1 Transportation and storage
The packaging consists of styrofoam and is itself packaged in Superwell cardboard.
The instructions printed on the outside are for transportation and storage, and have
the following meaning:
1. Transport upright; the arrows point upward
2. Protect from impact
3. Protect from moisture
4. Temperature -20 °C to + 55 °C
5. 5% to 95% non-condensating
6. Air pressure 700 hPa to 1060 hPa
4.1.2 Packed items
The operator stool PHYSIO Evo/Evo F/One is packed in a special carton. Besides the
operator stool, the packaging contains further modules according to the order.
The upholstery for the seat and backrest are packaged separately and must be moun‐
ted to the operator stool.
Weight: 15 kg
16 / 38
Page 17
Instructions for use PHYSIO Evo/Evo F/One
4 Installation | 4.2 Assembly of operator stool PHYSIO Evo/Evo F/One
4.2 Assembly of operator stool PHYSIO Evo/Evo F/One
Note
The PHYSIO Evo/One operator stool is delivered in the lowest seat height and with
the backrest folded forwards.
Note
Only specially trained personnel may work on or exchange parts of the seat adjust‐
ment element.
4.2.1 Mounting the castors
Note
Use the castors that are appropriate for the flooring.
Only use soft castors for hard flooring. Only use hard castors for soft flooring.
▶ Insert the castors into the stool base and press until the castors engage.
▶ Pull the castors lightly to ensure that they have securely engaged.
17 / 38
Page 18
Instructions for use PHYSIO Evo/Evo F/One
4 Installation | 4.2 Assembly of operator stool PHYSIO Evo/Evo F/One
4.2.2 Mounting the upholstery
▶ Engage the seat upholstery at the 4 ball pins.
18 / 38
Page 19
Instructions for use PHYSIO Evo/Evo F/One
4 Installation | 4.2 Assembly of operator stool PHYSIO Evo/Evo F/One
4.2.3 Mounting the backrest upholstery
▶ Engage the backrest upholstery at the 4 ball pins.
19 / 38
Page 20
Instructions for use PHYSIO Evo/Evo F/One
4 Installation | 4.2 Assembly of operator stool PHYSIO Evo/Evo F/One
4.2.4 Adjust the gas pressure spring
Note
The pressure point of the gas pressure spring is set at the factory. If the seat height
of the operator stool PHYSIO Evo/Evo F/One cannot be adjusted securely, the
pressure point of the gas pressure spring must be adapted.
See also:
2 6.1.1 Adjusting the seat height, Page 30
▶ Incline the seat forwards and remove the upholstery.
▶ Adjust the pressure point as described below using a Phillips screwdriver:
Screw in the screw, the gas pressure spring is unlocked earlier.
Loosen the screw, the gas pressure spring is unlocked later.
▶ Remount the seat upholstery.
20 / 38
Page 21
Instructions for use PHYSIO Evo/Evo F/One
1
2
3
4 Installation | 4.3 Assembly of operator stool PHYSIO Evo F
4.3 Assembly of operator stool PHYSIO Evo F
Note
The chair is equipped with soft castors for hard floors as a standard.
Use the castors that are appropriate for the flooring.
Only use soft castors for hard flooring. Only use hard castors for soft flooring.
4.3.1 Mounting the top part of the chair
▶ Mount the intervention protection cover ① to the top part of the chair, slide them
together and guide over gas pressure spring ②.
▶ Place the top part of the chair ③ on the gas pressure spring ②.
21 / 38
Page 22
Instructions for use PHYSIO Evo/Evo F/One
4 Installation | 4.3 Assembly of operator stool PHYSIO Evo F
4.3.2 Mounting the upholstery
▶ Engage the seat upholstery at the 4 ball pins.
4.3.3 Mounting the backrest cushion
▶ Engage the backrest upholstery at the 4 ball pins.
22 / 38
Page 23
Instructions for use PHYSIO Evo/Evo F/One
4 Installation | 4.3 Assembly of operator stool PHYSIO Evo F
4.3.4 Adjust the gas pressure spring foot control
▶ Use an Allen key to adjust the pressure point as follows:
Screw in the threaded pin, the gas pressure spring is unlocked earlier.
Loosen the threaded pin, the gas pressure spring is unlocked later.
23 / 38
Page 24
Instructions for use PHYSIO Evo/Evo F/One
1
2
3
5 Dismantling | 5.1 Dismantling the operator stool PHYSIO Evo/Evo F/One
5 Dismantling
Note
Only specially trained personnel may work on or exchange parts of the seat adjust‐
ment element.
5.1 Dismantling the operator stool PHYSIO Evo/Evo F/One
▶ Remove the backrest and seat upholstery to prevent damage.
▶ Position the operator stool at the highest position.
▶ Incline the seat forwards.
5.2 Removing the intervention protection cover of the gas pressure
spring
▶ Press the lugs of the interference protection outwards through the opening in the
underside of the stool ①. Turn the cover of the gas pressure spring ② until all
lugs have been pressed out ③.
24 / 38
Page 25
Instructions for use PHYSIO Evo/Evo F/One
5 Dismantling | 5.3 Dismantling the gas pressure spring
Note
If necessary, the upholstery must be removed and the interference protection must
be pressed downwards out of the seat cover using a screwdriver.
5.3 Dismantling the gas pressure spring
5.3.1 Dismantling the gas pressure spring Evo / One
Note
If the gas pressure spring is knocked out of the stool base too violently, this could
lead to damage to the paintwork of the PHYSIO Evo/One operator stool. To prevent
damage to the paintwork, you can place a piece of wood between the gas pressure
spring and the hammer.
▶ To prevent damage to the paintwork of the operator stool, carefully hammer the
gas pressure spring out of the stool base using a large rubber hammer. You can
place a piece of wood between the gas pressure spring and the hammer.
25 / 38
Page 26
Instructions for use PHYSIO Evo/Evo F/One
5 Dismantling | 5.3 Dismantling the gas pressure spring
▶ Hammer the gas pressure spring out of the stool base as far as the stool support.
26 / 38
Page 27
Instructions for use PHYSIO Evo/Evo F/One
5 Dismantling | 5.3 Dismantling the gas pressure spring
5.3.2 Dismantling the gas pressure spring Evo F.
▶ Dismantle the intervention protection cover of the gas pressure spring on the top
part of the chair.
See also:
2 5.2 Removing the intervention protection cover of the gas pressure spring, Page
24
▶ Hammer the gas pressure spring out of the stool base.
▶ Remove the intervention protection cover of the gas pressure spring.
27 / 38
Page 28
Instructions for use PHYSIO Evo/Evo F/One
5 Dismantling | 5.3 Dismantling the gas pressure spring
▶ Dismantle the actuator plate.
▶ Unscrew 3 countersunk screws.
28 / 38
Page 29
Instructions for use PHYSIO Evo/Evo F/One
5 Dismantling | 5.3 Dismantling the gas pressure spring
▶ Dismantle the spring mechanism from the standpipe.
▶ Use the soft hammer and an appropriate pipe, e.g. larger-sized socket wrench, to
drive the gas pressure spring out of the base.
▶ To mount the new gas pressure spring, proceed in reverse order.
29 / 38
Page 30
Instructions for use PHYSIO Evo/Evo F/One
3
1
2
6 Operation | 6.1 PHYSIO Evo
6 Operation
6.1 PHYSIO Evo
PHYSIO Evo
Adjust the seat height
①
Adjust the backrest angle
③
Adjust the seat angle
②
6.1.1 Adjust the seat height
▶ Activate the lever ① on the left forwards.
▶ Load or unload the seat according to the required height.
▶ Release the front lever ① on the left to fix the required seat height.
6.1.2 Adjusting the seat
Note
The seat angle is adjusted individually to the operator as a rule.
▶ Loading the seat and backrest.
▶ Press the rear lever ② on the right downwards until the lever ② engages.
▶ Incline the seat as you wish.
▶ release the rear lever ② on the right to fix the position of the seat.
30 / 38
Page 31
Instructions for use PHYSIO Evo/Evo F/One
6 Operation | 6.1 PHYSIO Evo
6.1.3 Adjust the backrest angle
Note
There are two methods to adjust the backrest:
- Freely selectable inclination with lock
- Freely moveable backrest for active support of the back muscles
▶ Loading the seat and backrest.
▶ Press the rear lever ③ on the left downwards until the lever ③ engages.
▶ Incline the backrest as you wish.
▶ Release the rear lever ③ on the left to fix the position of the backrest.
or
▶ Let the rear lever ③ on the left engage.
ð The backrest is freely moveable and allows active support for the back muscles.
31 / 38
Page 32
Instructions for use PHYSIO Evo/Evo F/One
1
3
2
6 Operation | 6.2 PHYSIO Evo F
6.2 PHYSIO Evo F
PHYSIO Evo F
Foot actuator plate for adjustment of
①
Adjust the seat angle
②
the seat height
Adjust the backrest angle
③
6.2.1 Adjust the seat height
▶ Actuate the foot actuator plate ① by foot.
▶ Load or unload the seat according to the required height.
▶ Release the foot actuator plate ① to fix the seat height as desired.
6.2.2 Adjusting the seat
Note
The seat angle is adjusted individually to the operator as a rule.
▶ Loading the seat and backrest.
▶ Press the rear lever ② on the right downwards until the lever ② engages.
▶ Incline the seat as you wish.
▶ release the rear lever ② on the right to fix the position of the seat.
32 / 38
Page 33
Instructions for use PHYSIO Evo/Evo F/One
6 Operation | 6.2 PHYSIO Evo F
6.2.3 Adjust the backrest angle
Note
There are two methods to adjust the backrest:
- Freely selectable inclination with lock
- Freely moveable backrest for active support of the back muscles
▶ Loading the seat and backrest.
▶ Press the rear lever ③ on the left downwards until the lever ③ engages.
▶ Incline the backrest as you wish.
▶ Release the rear lever ③ on the left to fix the position of the backrest.
or
▶ Let the rear lever ③ on the left engage.
ð The backrest is freely moveable and allows active support for the back muscles.
33 / 38
Page 34
Instructions for use PHYSIO Evo/Evo F/One
1
2
6 Operation | 6.3 PHYSIO One
6.3 PHYSIO One
PHYSIO One
Adjust the seat height
①
Adjust the backrest / seat angle
②
6.3.1 Adjust the seat height
▶ Activate the lever ① on the left forwards.
▶ Load or unload the seat according to the required height.
▶ Release the front lever ① on the left to fix the required seat height.
6.3.2 Adjusting the seat and backrest
Note
The seat and backrest of the PHYSIO One operator stool are firmly connected.
▶ Loading the seat and backrest.
▶ Press the rear lever ② on the right downwards until the lever ② engages.
▶ Incline the seat and backrest as you wish.
▶ Release the rear lever ② on the right to fix the seat and backrest.
34 / 38
Page 35
Instructions for use PHYSIO Evo/Evo F/One
7 Reprocessing methods according to DIN EN ISO 17664 | 7.1 General care instructions
7 Reprocessing methods according to DIN EN ISO 17664
7.1 General care instructions
CAUTION
Product damage due to improper disinfection.
Malfunctions.
▶ Use disinfectant in accordance with the manufacturer's instructions!
▶ Only disinfect by wiping!
▶ Do not immerse product or product parts in liquids!
Damage to the paint surfaces as well as plastics can arise from the wide variety of
medicines and chemicals used in the dentist's office.
Tests have shown that there is no surface protection available that works with all com‐
mercially available agents.
As damage to the surface by these agents is very much dependent on the exposure
time, it is essential to wipe the affected areas using a moist cloth.
Any residue arising from disinfectants can be cleaned to a certain degree on painted
and plastic surfaces using neutral, nonabrasive rinses and cleansers.
New painted surfaces that still cause water to bead can be cleaned with water and
nonabrasive, mild cleansers.
7.2 Cleaning and disinfection
▶ Use disinfectants according to the manufacturer's instructions for use.
▶ Observe the safety data sheet of the manufacturer of the relevant disinfectant.
▶ Clean all surfaces with a soft cloth and an approved disinfectant.
Approved disinfectants:
▪ Mikrozid AF (liquid or cloths); manufacturer: Schülke & Mayr
▪ FD 322; manufacturer: DÜRR Dental GmbH
▪ Incidin Liquid; manufacturer: Ecolab
▪ CaviCide; manufacturer: Metrex
35 / 38
Page 36
Instructions for use PHYSIO Evo/Evo F/One
8 Troubleshooting | 7.2 Cleaning and disinfection
8 Troubleshooting
Note
The pressure point of the gas pressure spring is set at the factory. If the seat height
of the operator stool PHYSIO Evo/Evo F/One cannot be adjusted securely, the
pressure point of the gas pressure spring must be adapted.
See also:
2 4.2.4 Adjust the gas pressure spring, Page 20
See also:
2 4.3.4 Adjust the gas pressure spring foot control, Page 23
36 / 38
Page 37
Page 38
1.010.1992 · Fk · 20141205 - 5 · en
Loading...