Karcher K2.19 User Manual

K 2.19
Operating Instructions
Before first use of the unit read these operating instructions and act in accordance with them.
5.961-753.0 (11/07)
Dear Customer,
Please read and comply with
these instructions prior to the in­itial operation of your appliance. Retain these operating instructions for future refer­ence or for subsequent possessors.
Proper Use
This high-pressure cleaner is designed for domestic use only: – to clean machines, vehicles, buildings,
tools, facades, terraces, garden equip­ment etc. using a high-pressure water jet (and detergents if required).
– with accessories, replacement parts
and detergents approved by Kärcher. Observe the instructions provided with these detergents.
Environmental protection
The packaging material can be recy­cled. Please do not place the packag­ing into the ordinary refuse for disposal, but arrange for the proper recycling.
Old appliances contain valuable ma­terials that can be recycled. Please arrange for the proper recycling of old appliances. Please dispose your old appliances using appropriate collec­tion systems
Description of the Appliance
When unpacking the product, make sure that no accessories are missing and that none of the package contents have been damaged. If you detect any transport dam­ages, please contact your dealer.
Illustrations on Page 2
1 Power cord with plug 2 ON/OFF switch for appliance 3 Safety catch 4 High pressure hose 5 Handgun 6 Spray lance with High pressure-nozzle 7 Connection for water supply with filter 8 Coupling unit 9 Detergent suction hose with filter 10 High pressure outlet 11 Connection for detergent suction hose 12 Accessory mount for spray lance
Warranty
The terms of the guarantee applicable in each country have been published by our respective national distributors. We will re­pair possible faults on your unit free of charge within the warranty period, insofar as the faults are caused by material defects or defective workmanship. Guarantee claims should be addressed to your dealer or the nearest authorized customer service centre, and supported by documentary evi­dence of purchase.
English 3
Safety instructions
Danger
Never touch the mains plug and the
socket with wet hands.
The appliance must not be used if the
power cable or important parts of the ap­pliance, e.g. safety devices, high-pres­sure hoses, spray guns, are damaged.
The appliance may not be used in areas
where a risk of explosion is present.
If the appliance is used in hazardous ar-
eas (e.g. filling stations) the correspond­ing safety provisions must be observed.
Check the power cord with mains plug
for damage before every use. If the power cord is damaged, please arrange immediately for the exchange by an au­thorized customer service or a skilled electrician.
High-pressure jets can be
dangerous if improperly used. The jet may not be directed at persons, ani­mals, live electrical equipment or at the appliance itself.
The jet must not be directed at other
persons or directed by the user at him/ herself to clean clothing or footwear.
Never use the appliance to clean ob-
jects containing hazardous substances (e.g. asbestos).
Vehicle tyres or tyre valves are suscep-
tible to damage from the high-pressure jet and may burst. The first indication of this is a discolouration of the tyre. Dam­aged vehicle tyres/tyre valves are high­ly dangerous. Ensure that a distance of at least 30 cm is observed when clean­ing with the jet!
Never draw in fluids containing solvents
or undiluted acids and solvents! This in­cludes petrol, paint thinner and heating oil. The spray mist thus generated is highly inflammable, explosive and poi­sonous. Do not use acetone, undiluted acids and solvents as they are aggres­sive towards the materials from which the appliance is made.
Warning
Check the high-pressure hose for dam-
age before every use. Please arrange for the immediate exchange of a dam­aged high-pressure hose.
High-pressure hoses, fixtures and cou-
plings are important for the safety of the appliance. Only use high-pressure hos­es, fixtures and couplings recommend­ed by the manufacturer.
This appliance was designed to be
used with detergents which are sup­plied or recommended by the manufac­turer. The use of other detergents or chemicals may compromise the safety of the appliance.
Unsuitable extension cables can be
hazardous. Only use extension cables outdoors which have been approved for this purpose and labelled with a suffi­cient cable cross section: 1 - 10 m: 1,5 mm
Note
This device is not intended for use by
persons (including children) with re­duced physical, sensory or mental abil­ities or lacking experience and/or knowledge, unless they are supervised by a person responsible for their safety or are instructed by these persons on the use of the device. Children should be supervised, in order to guarantee that they do not play with the device.
The operator must use the appliance
properly. When working with the appli­ance, he must consider the local condi­tions and pay due care and attention to other persons, in particular children, who are nearby.
Observe a distance of at least 30 cm
when using the jet to clean painted sur­faces to avoid damaging paintwork.
Cleaning operations which produce oily
waste water, e.g. engine washes, un­derbody washes, may only be carried out using washing stations equipped with an oil separator.
2
; 10 - 30 m: 2,5 mm
2
4 English
Wear protective clothing and safety
goggles to protect against back spray containing water or dirt.
Never leave the appliance unattended
when it is in operation.
Make sure that the power cable or ex-
tension cables are not damaged by run­ning over, pinching, dragging or similar. Protect the power cable from heat, oil, and sharp edges.
The connection between the power ca-
ble and extension cable must not lie in water.
All current-conducting parts in the work-
ing area must be protected against jet water.
The appliance may only be connected
to an electrical supply which has been installed in accordance with IEC 60364.
The appliance may only be connected
to alternating current. The voltage must correspond with the type plate on the appliance.
The minimum fuse rating required at the
socket outlet is 13 A (slow-blow).
To avoid accidents due to electrical
faults we recommend the use of sock­ets with a line-side current-limiting cir­cuit breaker (max. 30 mA nominal tripping current).
The plug and coupling of the extension
cable used must be watertight.
Always fully unroll electrical cables from
the cable drum.
Safety Devices
Safety devices serve to protect the user and must not be rendered inoperational or their functions bypassed.
Power switch
The switch prevents unintented starting of the appliance. Stop the appliance during breaks or after operation.
Safety catch
The safety catch on the trigger gun pre­vents the appliance from being switched on unintentionally.
High pressure hose
The high pressure hose is specially con­structed with reinforced walls to handle wa­ter pressure up to 11 MPa (1600 psi) - it is easily damaged and should be stored care­fully.
Do not kink.Do not drive vehicles over the hose.Do not expose the hose to sharp edges
or corners.
Misuse will lead to ballooning or premature failure and will invalidate warranty.
English 5
Commissioning and operation
High pressure operation
Water supply
According to the applicable regula­tions, the appliance must never be used on the drinking water net without a system separator. Use a suitable system separator manufactured by Kärcher; or, as an alternative, a system separator as per EN 12729 Type BA.
Water supply from mains
For connection values, see type plate/tech­nical data. Observe regulations of water supplier. Î Use a fibre-reinforced hose (not includ-
ed) with a standard coupling:
- Minimum diameter, 1/2 inches (13 mm)
- Minimum length, 7.5 m.
Î Screw the coupling unit (supplied) to
the water connection on the appliance.
Î Push the water supply hose onto the
coupling unit, then connect it to the tap.
Caution
Never operate the high-pressure cleaner when the tap is turned off as dry running will damage the High pressure pump. If the water supply is not clean, the Kärcher water filter must be used (special accesso­ry - order No. 4.730-059).
Start up
Î Screw high pressure hose on to high
pressure outlet on appliance.
Î Push the appropriate spray lance on to
the trigger gun and fasten it by turning it to the right through 90°.
Î Open tap. Î Plug in mains plug. Î Set main switch to “I/ON”. Î Press safety catch on the trigger gun to
release it and pull lever.
Risk of injury
The trigger gun is subjected to a recoil force when the water jet is discharged. Make sure that you have a firm footing and are also holding the trigger gun and spray lance firmly.
Spray lance with High pressure nozzle
Î For normal cleaning tasks.
Operation with detergents not possible
Operation with detergent
Note:
Detergent can only be added when the ap­pliance is being operated in low pressure mode. All washing brushes supplied by Kärcher are designed for use with detergents.
Î Detach spray lance from handgun.
Note: A low-pressure jet is generated if the spray lance is not attached to the handgun.
Detergent take-up from container
Î Place the end of the Detergent suction
hose in a container with Detergent solu­tion.
Recommended Cleaning Method
1 Spray a small dose of the detergent on
the dry surface, and allow it to react (make sure the detergent does not dry up).
2 Wash off the loosened dirt using the
high-pressure jet.
Detergents
To ensure a trouble-free operation of the appliance and to match the individual cleaning task, we recommend our Kärcher detergent and maintenance agents. Please ask for our advice, or request information on the products.
6 English
Interrupting operation
Î Release the lever on the trigger gun. Î During breaks, use the safety catch to
secure the trigger gun lever.
Î During longer breaks (more than 5 min-
utes), also turn the appliance off using the ON/OFF switch.
Finish operation
Î If detergent has been added: Suspend
detergent suction hose in a container filled with clear water, switch the appli­ance on for around 1 minute once the spray lance has been removed and rinse until water runs clear.
Î Release the lever on the handgun. Î Switch the appliance switch to "0/OFF“. Î Turn off tap. Î Press the lever on the handgun to re-
lease any remaining pressure in the system.
Î Disconnect the appliance from the wa-
ter supply.
Î Detach spray lance from the handgun. Î Briefly switch the appliance on ("I/ON“),
press the handgun lever until no further water is discharged (approx. 1 min).
Î Switch the appliance switch to "0/OFF“. Î Use the safety catch to secure the
handgun lever.
Î Pull out the mains plug. Î Roll up the power cord and loop it e.g.
round the handle.
Special accessories
Special accessories expand the possibili­ties of using your appliance. Please contact your Kärcher dealer for further information.
Maintenance and Care
Risk of electric shock
Always switch off the appliance and pull out the mains plug before care and mainte­nance work.
Cleaning
Prior to longer periods of storage, e.g. in the winter: Î Remove filter from suction hose for de-
tergent and clean with running water.
Î Pull out filter in water connection using
flat-nose pliers and clean with running water.
Maintenance
The appliance is maintenance-free.
Spare Parts
Only use original Kärcher spare parts. You will find a list of spare parts at the end of this document.
Storing the Appliance
Risk of frost
Protect the appliance and accessories against frost.
The appliance and its accessories can get destroyed through frost if there are any wa­ter residues in them. To avoid damage to them: Î Store the appliance and the entire ac-
cessories in a frost-safe room.
English 7
Troubleshooting
You can rectify minor faults yourself with the help of the following overview. If in doubt, please consult the authorized customer service.
Risk of electric shock
Always switch off the appliance and pull out the mains plug before care and mainte­nance work.
Warning
Repair works may only be performed by the authorized customer service.
Appliance does not start
Î Check whether the voltage indicated on
the type plate corresponds to the volt­age of the socket.
Î Check the power cable for damage.
Pressure does not build up in the appliance
Î Evacuate air from the appliance: Switch
on the appliance when the high pres­sure hose is not connected and allow it to run until the water which discharges from the high pressure outlet is free of bubbles. Then connect the high pres­sure hose again.
Î Clean the filter in the water supply con-
nection: This can be easily removed us­ing flat-nose pliers.
Î Check all supply lines to the high pres-
sure pump for leaks or blockages.
No detergent infeed
Î Detach the spray lance from the trigger
gun and work without the spray lance.
Î Clean the filter of the detergent suction
hose.
Î Check the detergent suction hose for
kinks.
Strong pressure fluctuations
Î Clean the high-pressure nozzle: Re-
move dirt and debris from the nozzle bore with a needle and rinse through with water towards the front.
Î Check the volume of incoming water.
High pressure pump leaking
Î Slight leakage from the high pressure
pump is normal. If the leakage increas­es contact the authorized customer service.
8 English
Technical specifications
Power connection
Voltage (1~50 Hz) 220-240 V Connected load 1,4 kW Mains fuse (slow-blow) 10 A Protective class II Protection class IP X5
Water connection
Max. feed temperature 40 °C Min. feed volume 8 I/min Feed pressure, 0,2-1,2 MPa
Performance data
Working pressure 8 MPa Max. permissible pressure 10 MPa Water flow rate 5,5 I/min Detergent flow rate 0,4 I/min Recoil force of handgun 12 N Hand-transmitted vibration
(ISO 5349) Sound pressure level
Lpa (EN60704-1) Sound power level
Lwa (2000/14/EG)
Dimensions
Length 390 mm Width 160 mm Height 260 mm Weight 4 kg
0,8 m/s
77 dB(A)
91 dB(A)
CE declaration
We hereby declare that the machine de­scribed below complies with the relevant basic safety and health requirements of the EU Directives, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the machine is modified without our prior approval.
Product: High-pressure cleaner Type: 1.601-xxx Relevant EU Directives
98/37/EC 2006/95/EC 2004/108/EC 2000/14/EC
Applied harmonized standards
EN 60335–1 EN 60335–2–79 EN 55014–1: 2006
2
EN 55014–2: 1997 + A1: 2001 EN 61000–3–2: 2000 + A2: 2005 EN 61000–3–3: 1995 + A1: 2001 + A2: 2005
Applied conformity evaluation method
Appendix V
Sound power level dB(A)
Measured: 90 dB(A) Guaranteed: 91 dB(A)
The undersigned act on behalf and under the power of attorney of the company man­agement.
CEO
Head of Approbation
Alfred Kärcher GmbH Co. KG Alfred Kärcher-Str. 28 - 40 D - 71364 Winnenden Phone: +49 7195 14-0 Fax: +49 7195 14-2212
English 9
Helpline
Karcher (UK) Limited operate a helpline al­lowing customers to discuss any problems experienced with our products. The helpline operates during normal busi­ness hours, if you have difficulty getting through, please understand that there are peak periods during the day when our con­sultants are unable to take all calls coming in. In these circumstances we would ask that you try to contact us again later in the day.
The helpline number is 01295 752200, open from 8.30am to 5.00pm Monday to Friday.
It helps us if you have the model number and data plate details to hand before making your call.
Alternatively you may write or E-mail to the address below:
Karcher (UK) Limited Karcher House Beaumont Road Banbury Oxon, OX16 1TB
E-mail: info@karcher.co.uk
10 English
11
Loading...