CAUTION : To reduce the risk of electrical shock, do not remove
the cover. No user serviceable parts inside. Refer any servicing
to qualied Service personnel.
This symbol indicates that dangerous voltage consisting a risk of electric shock is present within
this unit.
This symbol indicates that there are important operating and maintenance instructions in the
literature accompanying this unit.
Read this manual carefully before using the product. The cautions described below contain important information
about safety, and are categorized into: Danger, Warning and Notice.
The company will not take any responsibility for accidents or damage resulting from careless handling by the user.
Danger
If the user mishandles the product, there is a risk of loss of life or critical injury.
Connect the power cord only to A/C outlets as specied by the user manual or product specication.
If the power code is connected to a non-specied A/C outlet, it could result in re or electric shock.
The product must not be exposed to water or liquid of any sort, or be exposed to drips or splashes.
It could result in re or electric shock.
Do not place heavy objects, including the product itself, on top of the power cord. If it is damaged, it could result in
re or electric shock.
Do not place metal objects on top of the apparatus. If metal objects fall into the apparatus, it could result in re or
electric shock.
Do not repair, disassemble or modify this apparatus yourself. It might cause re or electric shock.
If internal checking or maintenance is needed, please contact your service center or agency.
Do not block or cover any ventilation opening. A re might result from overheating.
Turn o and unplug the power as quickly as possible during electric storms.
Failure to do so could result in re or electric shock.
Remove the antenna’s power plug from the outlet as quickly as possible during electric storms.
Failure to do so could result in re or electric shock.
Do not drop the apparatus (for example by putting it in a place where it may fall) or subject it to impact.
The product might be damaged. If it is damaged, please turn o the power and remove the plug from the power
outlet, or re or electric shock may result.
Never touch the power cord with wet hands. It could result in an electric shock.
ENG - 3
Warning
If the product is mishandled, the user might receive a serious or minor injury.
Damage or loss to the user’s property might also result.
The product must not be exposed to water or liquid. If the apparatus is exposed to drips or splashes, it might cause
a problem that cannot be repaired.
Do not repair, disassemble or modify this apparatus yourself. It might be seriously damaged, possibly beyond repair.
Turn o the power and unplug the power cord as quickly as possible during electric storms.
They might damage the apparatus.
Remove the antenna’s power plug from the outlet as quickly as possible during electric storms, or the apparatus
might be damaged.
Data recorded in the HDD might be lost due to a shock, lightening or electricity failure.
The user must back up his or her own data, and the company does not take any responsibility for failure to do so.
Notice
If the product is mishandled, it might cause minor damage.
If the apparatus becomes marked, clean it gently with a soft cloth or towel. Never use chemical solvents such as
benzene, thinner, acetone or other solvents. The surface of the apparatus might become discolored and the paint
might peel.
Do not place or keep the apparatus in the following situations. Doing so might cause problems.
- Where it is too hot or cold.
- Where there is high humidity.
- Where there are excessive temperatures, for example in front of airconditioners or heating vents.
- Where there is dust or soot.
- In conned areas where the heat cannot be released.
- Where it is exposed to direct sunlight.
Turn the apparatus o or unplug the power cord if it is to remain unused for a long period of time.
Do not place heavy objects on top of this apparatus. It might cause malfunction or damage.
If the apparatus is so seriously damaged that it cannot be repaired, or has stopped working altogether, dispose of it
properly in accordance with the local laws or regulations in your area.
Disposal
Batteries and packaging material do not belong in domestic waste. The batteries must be delivered to a collection
center for old batteries. The separate disposal of packaging materials protects the environment.
Disposal old electrical & electronic equipment
(Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated
as household waste. Instead it shall be handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this product. The recycling
of materials will help to conserve natural resources. For more detailed information about recycling
of this product, please contact your local city oce, your household waste disposal service or the
shop where you purchased the product.
1.2 Front Panel ...........................................................................................................................................................6
1.5 Remote Control .................................................................................................................................................9
2. Setup
2.1 Connecting the Antenna ............................................................................................................................11
2.2 Connecting Your Equipment.....................................................................................................................11
2.3 Turning On and O Your Receiver ...........................................................................................................13
3. Easy installation
3.1 Language ..........................................................................................................................................................14
3.2 TV .......................................................................................................................................................................... 14
3.3 Screen Type ......................................................................................................................................................14
3.5 Time ..................................................................................................................................................................... 15
4.1 Changing the Channel.................................................................................................................................16
4.2 Volume Control ...............................................................................................................................................16
4.6 Sleep Time ........................................................................................................................................................17
4.7 Channel List ...................................................................................................................................................... 17
5.2 Program Guide ................................................................................................................................................ 21
5.3 Edit Channel List ............................................................................................................................................. 22
5.5 System Setting ................................................................................................................................................24
5.6 CA System .........................................................................................................................................................29
6. PVR Guide
6.1 Recorded List ...................................................................................................................................................30
6.2 Progress Bar ...................................................................................................................................................... 31
6.4 Time Shift Recording ....................................................................................................................................34
6.6 Multi Channel Recording ............................................................................................................................34
7.3 Menu Map......................................................................................................................................................... 38
7.4 Remote Control TV Setting ........................................................................................................................39
6 - ENG
1. Introduction
1.1 Package Contents
Make sure that the following accessories are supplied with your receiver.
Remote controlAAA Batteries (2 EA)User’s manual
1.2 Front Panel
3218
479
56
/ Channel (Programme)Press to change the channel or select a menu item.
1
/ Volume
OKPress to select a menu, or conrm the selected operation.
2 STOPPress to stop a recording or playback.
3 STANDBY (Power)Press to turn the receiver power on or o.
4 RECPress to record a programme.
5 MENU
6 EXITPress to exit and return to the previous menu and screen.
7 Display windowDisplays the current state such as channel, time, and massage.
8 ResetPress to restart the receiver.
9 Smartcard SlotSlot for Smartcard.
Press to adjust the volume or select a menu item.
Press to display the main menu on the screen or return to the previous
menu.
B The front of the product is subject to change without notice.
ENG - 7
1.3 Smartcard
Caution
Please do not plug in the main power supply cord until you have nished all of the connections!
Inserting a Smart card
A Smart card looks similar to a credit card and entitles you to view and listen
to all the channels you choose to subscribe to.
The Smart card slot on the receiver can be used for Smart cards only.
1. Open the right-hand cover on the front panel of the receiver.
2. Hold the Smart card horizontally with the electronic chip
(small square-shaped, gold in colour) facing upwards.
3. Insert the Smart card into the top slot.
Smartcard
8 - ENG
1.4 Rear Panel
317
2
1 ANT INConnect a CATV signals.
2 LOOP OUTConnect to other receiver.
3 VCR (SCART) Connect to the VCR with SCART cable.
4 TV (SCART)Connect to the TV with SCART cable.
5 S/PDIF (OPTICAL) Connect a digital amplier output
6 HDMI
7 RJ45Connect the LAN cable.
8 USBConnect the USB memory with USB cable.
9 ON/OFF (Power switch)Turn on and o the receiver.
10 Power supply90~250V AC, 50/60Hz
4568
Use the HDMI cable to connect this jack to the HDMI jack on
your TV for the best quality picture.
B The rear of the product is subject to change without notice.
910
ENG - 9
1.5 Remote Control
All the functions can be controlled with the remote control.
Some function can also be adjusted with the buttons on the front panel of the receiver.
Before you use the remote control, please install the batteries.
Basic functions
1. STANDBY Press to switch between operation and
standby mode.
1
211
3
4
5
6
7
8
9
10
2. SUB-T Press to enable or disable subtitle.
3. TV/STB Press to switch between TV and Receiver
mode.
4. TEXT Press to see the teletext by OSD.
5. TV/RADIO Press to switch between TV and Radio.
6. GUIDE Press to display the TV/Radio program
12
13
14
15
16
17
guide.
7. VOL (+/
8. MENU Press to display the main menu on the
9. Color buttons
Green(SORT): Press to sort channel list.Yellow: Press to perform functions in "PVR", “ Program
Blue(INFO): Press to display the information box
10. Numeric buttons Press to select the channel and
11. AUDIO Press to select the audio language or the
12. PRE-CH Press to return to the previous channel.
13. SLEEP Press to select a present time interval for
14. Mute Press to enable or disable audio temporarily.
15. /// (Arrow buttons) Press to move the
16. CH (+/-) Press to change channel up and down.
17. EXIT Press to return the normal viewing mode from
-
) Press to increase or decrease the volume.
screen or return to the previous menu.
Red: Press to perform functions in "PVR", “ Program
Guide” or “Edit Channel List” menu.
Guide” or “Edit Channel List” menu.
on the screen, or to perform functions in “Program
Guide” or “Edit Channel List” menu.
enter the PIN code.
sound mode. (Mono, Left, Right, Stereo).
automatic shut o.
cursor to the up, down, left or right menu option.
OK Press to selects a menu, or conrms the
selected operation.
a menu.
10 - ENG
1
2
7
8
9
10
1415
11
12
13
TV Control Buttons
1. TV STANDBY Press to turn on and o your TV.
2. TV Volume Press to increase or decrease the TV
3
4
5
volume.
3. TV MUTE Press to enable or disable the TV audio
temporarily.
4. INPUT Press to check the TV’s external connection
status and select an external device.
5. TV Channel Press to change the current TV
channel.
PVR Functions
6. Progress bar Press to display the progress bar
6
during playback or Time Shift.
7. Record Press to record the current channel to the
HDD.
8. Pause Press to pause.
9. Fast rewind Press to rewind at high speed. Each
time you press this button the rewind speed is
increased.
10. Play Press to play at normal speed or resumes.
11. Recorded List Press to display the recording list.
12. Stop Press to stop a recording or playback.
13. Fast forward Press to fast forward at high speed.
Each time you press this button the fast forward
speed is increased.
14. Instant replay Press to jump back and plays from
that location.
15. Commercial Skip Press to jump ahead in a
recording.
Installing Batteries in the Remote Control
When inserting batteries, make sure that the polarity
(+/-) is correct.
B The design of the remote control may be changed
without any notice in advance.
ENG - 11
2. Setup
There are several ways of connecting the receiver to your TV and VCR. Consult your local supplier for assistance in
setting-up your system that is best suited to your requirements.
2.1 Connecting the Antenna
Connect the antenna cable (RF cable) from cable system to the ANT IN jack of the receiver.
Connect a Loop through cable between the LOOP OUT and the ANT IN. (If not connected, you can not record.)
Cable system
HD PVR receiver
2.2 Connecting Your Equipment
2.2.1 Connecting a TV (SCART/AV jack)
Connect the receiver to a TV with SCART.
SCART cable
HD PVR receiver
TV
12 - ENG
2.2.2 Connecting a TV (HDMI jack)
Connect the receiver to a TV with HDMI jack, if your TV is equipped for it.
HD PVR receiver
HDMI cable
TV
B HDMI, or high-definition multimedia interface, is a next-generation interface that enables the transmission of
digital audio and video signals using a single cable without compression. “Multimedia interface” is a more accurate
name for it especially because it allows multiple channels of digital audio (5.1 channels). When connecting via
HDMI, you do not need to connect Audio Cables.
2.2.3 Connecting a VCR
Connect the receiver to a VCR with SCART.
SCART cable
VCR
HD PVR receiver
2.2.4 Loop Though
If you have another digital receiver and you wish to use the same antenna cable, then you can connect it via the
loop through. Connect one end of the coaxial cable to the Loop Through on the receiver and connect the other
end of the cable to the ANT IN jack on your second receiver.
ENG - 13
2.3 Turning On and O Your Receiver
Power On
1. Connect the power cord of the receiver to a wall outlet.
2. Turn on the power switch located at the back of the receiver.
3. Press the STANDBY button on the front of the receiver or on the remote control.
12
Power O
Press the STANDBY button again.
The receiver will display “O”.
3
3
3. Easy installation
Before you watch the television or radio program, you must perform the installation procedure rst.
Therefore you will see only “Easy Installation” menu at rst when you plug into your system.
The Easy Installation gives you the convenience of selecting various languages, adjusting the time and channel search.
3.1 Language
The rst option in “Easy Installation” is to select the desired language of
the Menu, Audio, or Subtitle.
Press the / button to select desired language and press the OK
button to change the language.
The Language of the Menu, Audio, or Subtitle will be changed to the
selected language.
3.2 TV
You can set the aspect ratio of your TV.
Press the / button to select desired option and press the OK button.
If you have a TV set with 4:3 picture format, select 4:3 TV and if you
have a TV set with 16:9 picture format, select 16:9 TV.
3.3 Screen Type
You can select the display format according to the TV screen ratio.
Press the / button to select desired option and press the OK button.
4:3 TVAuto, Letterbox, Center cut
16:9 TVAuto, Pillarbox, Pan and scan
ENG - 14
15 - ENG
3.4 Resolution
The receiver supports various video resolutions (576p, 720p, and 1080i).
Press the / button to select desired option and press the OK button.
3.5 Time
You can set your local time according to your location.
When “Auto” is selected
Press the / buttons to select desired country and press the OK button.
When “Manual” is selected
1. Press the / button to select the current time zone from standard time
and then press the OK button. When you press the / button, the time
zone will move by 30 minutes.
2. If you want to turn the Day Light Saving on, press the / button to
select “On” and press the OK button.
3.6 Search
You can search the channels according to the automatic or manual mode.
Please wait until the channel search is complete.
1. Press the / button to select "Homing", "Auto", "Manual", or
"NetworkID".
2. Press the /button to select the desired option and then press the
//Numeric button to set it as you want.
B For more information, refer to 5.4 Installation.
ENG - 16
4. Basic Functions
4.1 Changing the Channel
After the television channels have been programmed, you will see programme information for a few seconds each
time you change the channels.
You can change the current channel using one of the following methods.
You can change the channel using the CH +/
desired channel by entering its channel number with the Numeric (0-9)
buttons.
Press the PRE-CH button to return to the previous channel.
Press the TV/RADIO button to switch between TV channels and radio
channels.
You can change channel by using the channel banner, simple channel list,
or program guide.
4.2 Volume Control
Press the VOL +/- buttons to adjust the volume level.
Volume level bar is displayed.
Press the Mute button to temporarily stop the volume.
To cancel mute, press the Mute button again or press the VOL +/
buttons.
-
button and change to
-
4.3 Audio
If the current programme is available in multiple audio languages, you can
select the language that you wish to listen to.
1. Press the AUDIO button to display the audio menu.
2. Press the / button to select the required audio language and press the OK button.
3. Press the / button to select audio output (Mono, Left, Right, or
Stereo).
B You can change a default audio language in the system setting menu mode.
17 - ENG
4.4 Subtitle
4.5 Teletext
4.6 Sleep Time
If the current programme provides subtitle information, you can select the
language for the subtitle.
1. Press the SUB-T button to display the subtitle menu.
2. Press the / button to select the required subtitle language and press the OK button.
The subtitles will be displayed on the screen.
If the current programme provides teletext, you can watch teletext.
Press the TELETEXT button.
The teletext is displayed on the screen.
You can select a time period of between 10 and 90 minutes after which the
receiver automatically switches to standby mode.
Press the SLEEP button to select the preset time interval (O~90) for staying
on.
4.7 Channel List
1. When you press the OK button during receiving service stream, you can
view simple channel list.
2. Press the / button to select the required channel and then press the
OK button.
3. Press the TV/RADIO button to switch between TV channels and radio
channels.
To get the channel sort list
1. Press the Green button to display the channel sort list.
2. Press the / button to select the sort list you want and then press the
OK button to get it.
ENG - 18
4.8 Channel Banner
When you press the Blue button during receiving service stream, you can view channel banner.
Press the / button to select the channel and then press the OK button.
Press the / button to view to previous or next programme information.
Press the Blue button to view to the programme information.
1
5 6
1Programme name
2Programme broadcasting time
3Detailed programme infromation
4Icons
Displayed when the programme is recording.
Displayed when the channel provides HD programmes.
Displays the resolution of the current programmes.
Displayed when the programme is broadcast in Dolby Digital.
Displayed when the programme is broadcast in AAC Audio.
Displayed when the programme is broadcast in subtitle language.
Displayed when the programme is broadcast in teletext.
Displayed when the channel is a locked channel.
Displayed when the channel is a scrambled channel.
Indicates the minimum level of age for viewing the programme.
5Current channel number
6Current programme broadcasting time
7Next programme information
8Current channel name
9Current time
10Current programme progress bar
2
78
34
09
19 - ENG
5. Menu Guide
5.1 PVR
5.1.1 File List
File List manages the les and directories in the built-in HDD.
1. Press the / button to select “File List” on the PVR menu and press the
OK button.
2. Press the / button to select “AV”, “ MP3”, or “Photo” and press the OK
button. The les and directories saved in the HDD will appear.
3. Press the / button to select “AV”, “ MP3”, or “Photo” and press the OK
button.
AVDirectory that saves recorded les.
MP3Directory that saves MP3 les.
PhotoDirectory that saves photo image les.
Editing the File/Folder Lists
1. Press the Yellow button to display the edit menu on the File List menu.
2. Press the / button to select the desired option and press the OK
button.
3. Use the ////OK button to edit the selected le/folder list.
New DirectoryTo create a new directory in the current directory.
RenameTo change le or directory names. Characters such
DeleteTo delete a le or directory.
MoveTo change the position of the les.
CopyTo copy the le to built-in HDD or USB memory.
as 0~9, a~z, and A~Z can be used.
Using the / button, select the les you want to
move and press the OK button.
Using the / button, select the les you want to
move and press the OK button.
Sorting the File/Folder Lists
1. Press the Green button on the File List screen.
The le sort menu will appear.
2. Press the / button to select the arrangement method and press
the OK button.
TitleTo arrange les in le name order.
DateTo arrange les in date order.
ENG - 20
5.1.2 Reservation
You can set reserved recording functions including adding, changing and deleting reserved recordings.
1. Press the / button to select “PVR” in the main menu and press the OK
button.
2. Press the / button to select “Reservation” and press the OK button.
Reservation screen is displayed.
Adding
1. Press the Red button to display the add screen.
2. Press the / button on the add screen to select the items for setting.
ChannelTo select the channel you want to record.
ModeTo select the interval for the reserved recording.
DateTo set the date for the reserved recording.
StartTo set the time the reserved recording starts.
EndTo set the time the reserved recording ends.
3. Press the Red button to save.
Changing
1. Press the / button to select a reserved recording to be change and press the Yellow button.
2. When the edit screen appears, change the reserved recording in the same
way as you did with adding.
Deleting
Pressing the Green button on the edit screen deletes the selected
recording list only.
To delete all reserved recording lists, press the Green button on the
Reservation screen and then press the OK button.
You can choose to record once, daily or weekly.
If end time is passed, the reserved recording will stop.
B If you skip a reserved channel, or delete it, the reserved settings are canceled.
5.1.3 PVR Setting
You can use the PVR functions eectively by setting the following PVR options.
1. Press the / button to select “PVR” in the main menu and press the OK
button.
2. Press the / button to select “PVR Setting” and press the OK button.
The PVR Setting option is displayed.
3. Select the desired option and set it as you want.
Guard Time Start
Guard Time End
Default Record
Duration
Instant ReplayTo set the interval of instant replay time.
Commercial Skip To set the interval of skip time.
To set the guard time start of the reserved recording.
To set the guard time end of the reserved recording.
To set the default record duration.
21 - ENG
5.2 Program Guide
The program guide displays programme information about each channel, based on the date and time.
You can also reserve a recording by pressing the ● (Record) button.
5.2.1 Viewing the Program Guide Information
1. Press the / button to select “Program Guide” on the main menu and press the OK button.
You can access program guide simply by pressing the GUIDE button
on the remote control.
2. Press the EXIT or GUIDE button to exit the program guide screen.
///
OKTo switch the selected channel.
RedTo check the program guide on the desired date.
GreenTo sort the channel lists.
BlueIn case detailed info content is too long to check, you can
RecordTo reserve recording of the channel.
To move the cursor to the up, down, left, or right.
(among the currently serviced programs)
check its information as a long lists form, and resize its
lists by pressing Blue button.
B The Program Guide information might not be supported by the service
providers.
5.2.2 Recording Reservation by Program guide
You can set a programme to be record at a specic time by program guide.
1. Press the /// button to select to the programme to be record
and press the Record button.
The reservation icon is displayed.
2. Press the /// button to select the programme reserved and press
the Record button again.
3. Select the desired option and set it as you want.
4. Press the Red button to save.
You can check the reserved recording list by using the "PVR" >
“Reservation” menu.
You can also delete or edit the reserved recording list.
B For more information about recording reservation, refer to 5.1.2 Reservation.
ENG - 22
5.3 Edit Channel List
You can create favorite lists, lock, delete, or skip channel.
1. Press the / button to select “Edit Channel List” in the main menu and
press the OK button.
Enter the PIN code using the Numeric (0~9) button.
2. Press the / button to select the desired option and press the OK
button.
3. Among the all channel lists, the selected channel can be moved to the
right folder of “Lock, Delete, or Skip, Favorite (1~16)”.
To add from edit list at right folder, press the OK button.
To remove the channel list from edit list at right folder, press the OK
button.
To sort the channels, press the Green button. Select the desired
arrangement and press the OK button.
If you want to include all the channels in the channel list, press the Red
button.
To rename the favorite, press the Blue button.
4. To conrm the channel list, press the MENU button or EXIT button and
press the OK button to save.
B The PIN code preset to 0000 from the factory.
Lock
You can lock channels in any of the list in order to prevent e.g. your children
from watching.
1. Press the / button to select the channel you want to lock and press
the OK button.
2. Repeat the procedure for each channel you want to lock.
When you lock a channel in any list, the channel will be locked
automatically in all other lists.
Skip
You can skip the TV or Radio channel from the current list.
Press the / button to select the channel you want to skip and press the OK button.
To recover the skipped channel, press the OK button from edit list.
Favorite (Favorite 1~16)
You can edit favorite TV and Radio list. This enables you to create the 16
favorite TV and Radio lists.
Press the / button to select the channel you want to edit on the favorite
list and press the OK button.
23 - ENG
5.4 Installation
You can search the channels according to the automatic or manual mode. Please wait until the channel search is
complete.
Automatic Search
1. Press the Numeric buttons to set the Start Frequency, End Frequency,
and Symbol Rate of the cable signal.
2. Press the / button to select the constellation (“Auto, 16, 32, 64, 128,
or 256 QAM”).
3. Press the OK button and searching will start.
4. When searching is nished, press the OK button to save the channel list.
Manual Search
1. Press the Numeric buttons to set the Start Frequency and Symbol Rate of
the cable signal.
2. Press the / button to select the constellation (“Auto, 16, 32, 64, 128,
or 256 QAM”).
3. Press the / button to select the spectral invert (“Auto, O, or On”).
4. Press the / button to select for the network search (“O, or On”).
When you select “On”, you can nd more services using the home
network.
5. Press the OK button and searching will start.
6. When searching is nished, press the OK button to save the channel list.
Network ID
1. Press the Numeric buttons to set the Start Frequency and Symbol Rate of
the cable signal.
2. Press the / button to select the constellation (“Auto, 16, 32, 64, 128,
or 256 QAM”).
3. Press the / button to select the spectral invert (“Auto, O, or On”).
4. Press the Numeric buttons to set the Network ID.
5. Press the OK button and searching will start.
6. When searching is nished, press the OK button to save the channel list.
ENG - 24
5.5 System Setting
If you want to customize the system to suit you better, you can specify some settings from the submenus in the
“System Setting” menu.
1. Select “System Setting” in the main menu with the / buttons and
press the OK button.
2. Press the / button to select the sub menu and press the OK button.
5.5.1 Language
You can select the desired language of the Menu, Audio, or Subtitle.
Menu Language
You can select in which language the menus will be shown.
Press the / button to move to the language you want and press the OK
button.
First audio language/Second audio language
You can change default language for audio when changing services.
Press the / button to move to the language you want and press the OK
button.
B
Select the audio language between the first and second audio language.
If the first audio language is not selected, then the second audio language is
selected by default. (If both the first and second audio language are not available,
the audio language is set to the first audio language the selected channel supports
for.)
First subtitle language/Second subtitle language
You can change default language for subtitle when changing services.
Press the / button to move to the language you want and press the OK
button.
B
If you cancel the subtitle function, select the off.
Select the subtitle language between the first and second subtitle language.
If the first subtitle language is not selected, then the second subtitle language is
selected by default. (If both the first and second subtitle language are not available,
the subtitle language is set to the first subtitle language the selected channel supports for.)
25 - ENG
5.5.2 Time
You can set the Local time, Wakeup time, and Sleep time.
Time
You can set your local time according to your location.
When “Auto” is selected
Press the / buttons to select desired country and press the OK button.
When “Manual” is selected
1. Press the / button to select the current time zone from standard time,
then and press the OK button. When you press the / button, the time
zone will move by 30 minutes.
2. If you want to turn the Day Light Saving on, press the / button to
select “On” and press the OK button.
Wakeup Time/Sleep Time
You can set the On/O timers so that the receiver will switch on or o
automatically at the time you select.
1. Press the / button to select the desired option (“O”, “ Once”, “ Daily”,
“Weekly”, or “Weekday”).
2. Use the Colour//// button to select the year, month, and day
and then press the OK button.
3. Press the / button to move the cursor and then use the Numeric
(0~9) button enter the hour and minute.
ENG - 26
5.5.3 Lock Control
Channel Lock
When you change “Channel Lock” t o “ On” or “O”, service channel can get or
not from that set values.
If you select “On”, you need PIN code every time you select the lock
channel program as you set in the channel control.
If you select “O”, you can see all channels without PIN code.
Parental Rating Lock
Parental Rating Lock enables you to place certain restrictions on the
viewers by setting age limits. The password is required to view the blocked
programmes.
Press the / button to select to the desired option and press the OK
button.
Menu Lock
If the Menu Lock is set to “On”, the PIN code is needed to set the Edit Channel
List, Installation, Format HDD and System Setting.
Change PIN Code
You can change the PIN code from the standard 0000.
DO NOT FORGET IT! Without it, you are not able to access to any of the
functions where the code is required.
You can change password for Channel Lock and Menu Lock simultaneously.
1. Enter the current PIN code using Numeric (0~9) button on the remote
control.
2. In the selected New PIN code, enter a new PIN code.
3. To verify the new PIN code, re-enter a new PIN code in the selected
conrm PIN code.
If the PIN code is correct, the message “Success” will be displayed on
the screen.
B If you forget the PIN code, press the Colour button in sequence:
Red Green Yellow Blue.
The PIN code will be changed to “0000”.
27 - ENG
5.5.4 AV Setting
You can set various options related to input/output signals.
TV
You can set the aspect ratio of your TV.
Press the / button to select desired option and press the OK button.
If you have a TV set with 4:3 picture format, select 4:3 TV and if you have a
TV set with 16:9 picture format, select 16:9 TV.
Display Format
You can select the display format according to the TV screen ratio.
Press the / button to select desired option and press the OK button.
4:3 TVAuto, Letterbox, Center cut
16:9 TVAuto, Pillarbox, Pan and scan
Resolution
The receiver supports various video resolutions (576p, 720p, and 1080i).
Press the / button to select desired option and press the OK button.
SCART Output
If your SCART supports RGB control, select “SCART-RGB”.
Otherwise select “SCART-CVBS”.
ENG - 28
5.5.5 OSD Setting
You can adjust the on-screen transparency and set the banner time.
Menu/Teletext/Subtitle Transparency
From 20% to 100% will give the variable transparency on Video and OSD
screen.
Press the / button to select the desired transparency and then press the OK button.
The transparency will be applied on the screen.
Banner Time
When you switch channels, an information banner will be shown for a few
seconds. You can select for how long the banner will be shown.
Press the / button to select the banner time (1~10sec) you want and
then press the OK button.
Each selectable time items has meaning of the interval time during a
channel banner stays on changed channel screens.
Slideshow Time
Press the / button to select the slideshow time (1~10sec) you want and
then press the OK button.
5.5.6 Software Upgrade
Software can be downloaded through OTA (Over The Air) or USB connection.
OTA Upgrade
It is possible to set up OTA upgrade manually.
Please check if there is new software as pressing the OK button after
entering Frequency.
Updated software will be downloaded.
USB Upgrade
You can upgrade the software using theUSB jack of the receiver.
1. Press the / button to select “USB Upgrade” and press the OK button.
2. Press the / button to select the upgrade le and press the OK
button. The software upgrade will begin.
29 - ENG
5.5.7 Factory Reset
Use this option only if you have to start the complete installation procedure from scratch.
If you perform the Factory Reset, all your previous settings and all channels will be cleared! The default data will be loaded.
1. Press the / button to select “Factory Reset” and then press the OK
button.
2. If you want to reset, press the OK button, or press the EXIT button to exit
this menu.
5.5.8 System Information
Displays the system information: Model name, S/W, H/W, Loader version.
Press the / button on the Setup list to select “System Information”.
5.6 CA System
The menus are provided by the CA module and its smart card.
Your receiver is equipped with 1 slot of smart card.
Plug in the appropriate a valid smart card.
You will then have access to the respective scrambled and Pay-Per-View
services provided.
Insert the smart card into the slot. The smart card determines the programs
that can be de-scrambled. The smart card contains your subscription details
so that you can view your entitlement.
If you do not insert the smart card, you will see the message “No smart
card”.
If you insert the smart card into the slot then you can watch your selected
channel.
ENG - 30
6. PVR Guide
6.1 Recorded List
You can check the recorded programme on “File List”.
6.1.1 Recorded List screen
Press the Recorded List button on the remote control to display the recorded list. The recorded list displays as the
following. Also you can view the recorded list in the "PVR" > "File List" menu.
1
2
3
4
5
1Path of present folder
2
3
4
5
6
7
8
9
Recorded programme list
MP3 le list
Photo le list
Thumbnail of recording
Folder icon
File Icon
File name, time, date, duration
Button help
6
7
8
9
0
10
Used size of HDD
B When a USB memory is connected to the USB jack, the USB icon is displayed on left of File List screen.
31 - ENG
6.1.2 Play Option
6.2 Progress Bar
1. Press the Recorded List button on the remote control.
The recorded list will appear.
2. Press the / button to select the desired programme and press the
press the OK button.
BeginTo play the programme from the beginning.
ContinueTo continue to play from the previous stop
point.
DescrambleTo descramble le and store it again.
CancelTo cancel playback.
3. Press the / button to select “Begin” or “Continue” and press the press the OK button.
The selected programme is played back.
When press the Progress bar button on the remote control, progress
bar is displayed on the screen.
To display the help box, press the Blue button while the progress bar
appears on the screen.
Press the Progress bar button while watching a recorded programme to
display the progress bar. Progress bar displays the current play status, the
recorded time, and elapsed time.
6.3 Playback
The programme can be played in various ways.
6.3.1 Fast-Forward/Rewind
The Fast-Forward and Rewind functions enable the user to view the forward, backward or any desired part of the
programme.
To view forward parts press the
previous parts press the
Each time you press the button, the speed increases. (x2, x4, x8, x16, x32)
Press the (Play) button at the desired place to play at the recorded
speed.
(Fast Forward) button and to view
(Fast Rewind) button on the remote control.
ENG - 32
6.3.2 Slow motion
6.3.3 Instant Replay
6.3.4 Commercial Skip
Press the (Pause) button during playback, and press the (Fast
rewind) /
motion.
Each time you press the button, the prograqmme plays at 2x, 4x, 8x, 16x,
and 32x speed.
Press the (Play) button to play at the recorded speed.
Press the (Replay) button to jump back and play from that location.
When the replay is completed the programme will play from the current
point.
You can set the replay time interval by using the PVR setting menu.
Press the (Skip) button to jump forward and play from that location.
When the skip is completed the programme will play from the current
point.
You can set the skip time interval by using the PVR setting menu.
(Fast forward) button to play backward/forward as slow
6.3.5 Direct jump
1. Press the Progress bar button on the currently playing screen.
The progress bar will appear.
2. Press and hold the / button to move the location icon to a time point
and release the / button to play the programme from the specied
time point.
33 - ENG
6.3.6 Repeat A-B
You can set a specic block within a recorded programme and play it back repeatedly.
Press the Yellow button once at the start position and press the Yellow button again at the end position.
The programme is played back the selected block repeatedly.
To stop repeat mode
1. Press the OK button.
2. Press the / button to select “O repetition” and press the OK button. Alternatively you can use the Yellow button.
6.3.7 Bookmark
Use bookmarks to search positions quickly and conveniently.
1. Press the Progress bar button on the currently playing screen.
The progress bar will appear.
2. Press the Red button at a certain position to set a bookmark.
3. Press the Green button to display bookmark list and press the /
button to select the location you want to view.
4. To delete a bookmark, select the location you want to delete and press
the Red button.
ENG - 34
6.4 Time Shift Recording
The receiver automatically saves the programme in the built-in hard disk
drive temporarily, so that users can pause, play, fast rewind, fast forward,
replay, etc. even while watching the currently broadcasting TV programme.
When you press the
will be start.
6.5 Instant Recording
You can record a programme using the built-in hard disk drive without an
external media device.
Press the ● (Record) button to record the current programme instantly.
The record icon and default record time is displayed.
6.6 Multi Channel Recording
You can record two channels simultaneously.
(Fast Rewind) or (Pause) button, the time shift
6.7 Stop Recording
1. Press the ∎ (Stop) button.
The stop list is displayed.
2. Press the / button to select the recording list to be stop and press
the ∎ (Stop) button.
35 - ENG
6.8 MP3/Photo
You can play MP3 or photo les stored on built-in hard disk drive, USB memory.
Use a USB cable to connect the USB memory to the receiver.
6.8.1 Connecting the USB Memory
1. Save MP3 and image les into USB memory from your PC.
2. Connect the USB memory to USB jack on the receiver.
6.8.2 Playing back the Files
1. Press the / button to select “PVR” in the main menu and press the OK
button.
2. Press the / button to select “File List” and press the OK button.
3. Press the / button to select “MP3” or “Photo” and press the OK
button.
The MP3 or Photo les are displayed.
4. Press the / button to select the desired le and press the press the
OK button.
The selected le is played back.
ENG - 36
7. Supplement
7.1 Troubleshooting
ProblemSolution
No display LED on the front panel.
No power supply.
No picture.
Poor picture quality.
No sound.
Remote control does not operate.
Service is not running or scrambled.
You have forgotten your secret PIN
code.
Power cord plug in correctly.
Ensure that the receiver is switched on.
Check connection and correct.
Check channel and video output and correct.
Check the signal level, if it is low.
Check that the RF cable is properly connected.
Check the volume level of the TV and receiver.
Check the mute status of the TV and receiver.
Point remote control directly towards the receiver.
Check and replace batteries.
Check that nothing blocks the front panel.
Check that the smart card is appropriate for the selected service.
Refer to change PIN code of this user’s manual.
37 - ENG
7.2 Technical Specication
System Resources
Flash Memory
Program DRAM
EEPROM
MPEG TS A/V DECODING
Transport stream
MPEG Prole/level
Input bit rate
Video aspect ratio
Video formats
Video outputs
Audio decoding
Audio modes
Sampling rate
DATA INPUT/OUTPUT
Output connectors
Descrambling & Access control
Standard
Number of smart card slots
Location
Standard
Power Supply(Internal)
Input Voltage
Power Consumption
Protection
Type
Hard disk
Interface
Capacity
Physical Specication
Operation Temperature
Storage Temperature
Size (W*H*D)
Net weight
32Mbytes
256Mbytes
32KBytes
MPEG-4/H.264 HP@L4.0 1920x1080 interface@50Hz
MPEG-2 MP@HL, MPEG-4/AVC MP@L4
Max. 81,0 Mbit/Sec.
4:3, 16:9, Letter Box
576p, 720p, 1080i
SD output: PAL
HD Resolution: 1080i, 720P, 576P
Dolby AAC, AC-3, MPEG-1 layers 1,2 and 3 (MP3)
Single Mono, Dual mono, Stereo, Joint stereo
32,0, 44,1 and 48,0 kHz
SCART TV and SCART VCR
SPDIF(OPTICAL),
HDMI, RJ45, USB2.0
DVB common Scrambling algorithm (ETR 289)
ONE slot
(One smartcard slot is included in the front panel.)
Front panel
Connector on bottom side of smartcard
ISO 7816 Part 3
AC 90-250V, 50/60Hz
40W
Separate Internal Fuse
SMPS
SATA
250~500 Gbytes
0˚ ~ 50˚C
-20˚ ~ 60˚C
370*60*280 mm
3.0Kg
ENG - 38
7.3 Menu Map
PVRFile ListAV
Program Guide
Edit Channel List
MP3
Photo
Reservation
PVR SettingGuard Time Start
Guard Time End
Default Record Duration
Instant Replay
Commercial Skip
InstallationAutomatic Search
System Setting
CA SYSTEM
Manual Search
Network ID
LanguageMenu Language
First audio language
Second audio language
First subtitle language
Second subtitle language
TimeTime
Wakeup Time
Sleep Time
Lock ControlChannel Lcok
Parental Rating Lock
Menu Lock
Change PIN Code
AV SettingTV
Display Format
Resolution
SCART Output
OSD SettingMenu Transparency
Teletext Transparency
Subtitle Transparency
Banner Time
Slideshow Time
Software UpgradeOTA Upgrade
USB Upgrade
Factory Reset
System Information
39 - ENG
7.4 Remote Control TV Setting
7.4.1 Checking the Set-Up Code
1. Press the TV STANDBY button with OK button on the remote control for 2 seconds to covert to Setting Mode.
It will convert to the Setting Mode after the LED is on.
2. Press the INFO button.
Set-up code will blink in oder as number of 100 digits, 10 digits, 1 digits. (Only 0 is blink 10 times.)
7.4.2 Using the Three Digit Code
1. Press the TV STANDBY with OK button on the remote control for 2 seconds to convert to Setting Mode.
It will convert to the Setting Mode after the LED is on.
B Setting mode will be exited if no input is made for more than 20 seconds.
2. Point the remote control toward the TV.
3. Find the 3-digit code for your manufacturer on the list below, and enter the code by using the number buttons.
The LED will blink once each time you enter the number.
4. Press the OK button to nish.
The LED will blink 2 times and becomes "O" status.
B Some buttons may not work.
7.4.3 Using the Auto Search (TV CH+/-)
1. Press the TV STANDBY with OK button on the remote control for 2 seconds to convert to Setting Mode.
It will convert to the Setting Mode after the LED is on.
B Setting mode will be exited if no input is made for more than 20 seconds.
2. Point the remote control toward the TV.
3. Press the TV CH + or - button.
The LED will blink once each time you press the button.
4. Press the OK button to nish.
The LED will blink 2 times and becomes "O" status.
B Some buttons may not work.
7.4.4 Resetting the TV to the Factory Defaults
Press the TV STANDBY with (Record) button on the remote control for 5 seconds.
After the LED blinks 5 times, resets all settings to the default values.
ENG - 40
7.4.5 TV Code Lists
Manufacturer/Brand Set-Up Code NumberManufacturer/Brand Set-Up Code Number