INSTRUCTION
BOOKLET
KTF840_841_WHT_IB_C18.indd 1 19/6/18 1:42 pm
Suits all KTF840 & KTF841
models
Important
Please retain your instruction
book for future use.
In the event that you need some assistance with your
Kambrook appliance, please contact our Customer Service
Department on 1300 139 798 (Australia) or 0800 2738 45
(New Zealand). Alternatively, visit us on our website at
www.kambrook.com.au or www.kambrook.co.nz
KTF840_841_WHT_IB_C18.indd 2 19/6/18 1:42 pm
Contents
Kambrook Recommends
Safety First
Your Kambrook 87cm or
114cm Touch Control Tower Fan
Quick Start Guide p7
Using Your Tower Fan p8
Care, Cleaning and Storage p13
p4
p6
KTF840_841_WHT_IB_C18.indd 3 19/6/18 1:42 pm
Kambrook Recommends Safety First
IMPORTANT: Please retain your
instruction book for future use.
At Kambrook, we believe that safe performance is the first priority in any
consumer product, so that you, our valued customer can confidently
use and trust our products. We ask that any electrical appliance that
you use be operated in a sensible fashion with due care and attention
placed on the following important operating instructions.
Important Safeguards For Your Kambrook
Arctic Remote Controlled Tower Fan
• Carefully read all instructions before
operating the appliance for the first time and
save for future reference.
• Remove and safely di scard any packa ging
material and promotional labels before using
the appliance for the first time.
• To eliminate a choking hazard for young
children remove and safely discard the
protective cover fitted to the power plug of
this cooling fan.
• When unpacking the tower fan, check to see
you have received all the items listed in the
parts list, before discarding the packa ging.
• Do not place the tower fan near the edge
of a bench or table during operation. Ensure
that the sur face is level, clean and free of
water and other substa nces
• Always ensure the tower fan is properly
assembled before u se. Follow the
instructions provided in this book.
• This tower fan is intended for household u se
only and not for commercial or i ndustrial use.
• To avoid electrical circuit overload, it is
recommended that no other appliances are
plugged into the same circuit as your fan,
when it is in use.
• Di sconnect the power plug before
assembling, dismantling or before cleaning
and when the fan is not in u se.
• Avoid touching mobile parts of the fan.
• Never insert fingers , pencils or any other
objects through the guards whenever the
power plug is connected, in particular while
the tower fan is switched on.
• The tower fan mu st not be used if the base
is not fastened correctly, according to the
instructions provided in this book.
• Do not operate i n the presence of explosives
and/or flammable fumes or liquids.
• Do not leave the tower fan unattended
when in use.
• Do not unplug the tower fan by pulling on
the cord.
• Never carry the tower fan by the cord or yank
to disconnect from an outlet; instead, grasp
the cord a nd pull to disconnect.
• Do not pull the cord around sharp edges or
corners.
• Allow the fan blade to stop completely,
always switch of f at the power outlet, and
then unplug the appliance from the outlet:
- Before leaving it unattended
- Before attem pting to move the appliance
- Before cleaning and maintenance unless
otherwise specified in this booklet
- Immediately af ter use.
• To prevent damage to the fan do not use
alkaline cleaning agents when cleaning,
uses a soft cloth and mild detergent.
• Do not place a nyth ing, on top of the tower
fan when assembled, when in use and when
stored.
4
KTF840_841_WHT_IB_C18.indd 4 19/6/18 1:42 pm
• Switch off the tower fa n and unplug at the
power outlet, prior to assembling , clea ning
and storing the tower fan.
• Do not place a nyth ing, on top of the fan
when assembled, when in use and when
stored.
• Store the unit out of reach of children.
• Keep the tower fan clean. Follow the
cleaning instructions provided in this book.
Important Safeguards For All Electrical
Appliances
• Fully unwind the power cord before use.
• Connect only to a 230V or 240V power outlet.
• Do not let the power cord hang over the
edge of a bench or table, touch hot surfaces
or become knotted.
• To protect against electric shock, do not
immerse the power cord, power pl ug or
appliance in water or any other liquid or
allow moisture to come in contact with
the part, unless it is recommend ed in the
cleaning instructions.
• The appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience a nd knowledge,
unless they have been given super vision or
instruction concerning use of the appliance
by a person responsible for their safety.
• Children should be supervised to ensure that
they do not play with the appliance.
• It is recommended to regularly inspect the
appliance. To avoid a hazard, do not use
the applia nce if power cord, power plug or
appliance becomes damaged i n any way.
Return the entire appliance to the nearest
authorized Kambrook service centre for
examination and / or repair.
• Any maintenance other than cleaning
should be performed at an authorised
Kambrook Service Centre
• This appliance is for household use on ly.
Do not use this a ppliance for anything other
than its intended use. Do not use in moving
vehicles or boats. Do not use outdoors.
Misuse may cause injury.
• The insta llation of a residual current device
(safety switch) is recommended to provide
additional safety protection when using
electrical appliances. It is advisabl e
that a safety switch with a rated res idual
operating current not exceeding 30mA be
installed in the electrical circuit supplying
the applia nce. See your electrician for
professional advice.
• Always turn the appliance to the OFF
position, switch off at the power outlet
and unplug at the power outlet when the
appliance is not in u se.
• Before clea ning, always turn the appliance
to the OFF position, switch of f at the power
outlet, unplug at the power outlet and
remove the power cord, if detachable, from
the applia nce and allow a ll parts to cool.
• Do not place this appliance on or near
a heat source, such as hot p late, oven or
heaters.
• Pos ition the appliance at a minimum
distance of 20cm away from walls, curtains
and other heat or steam sensitive materials
and provide adequate space above and on
all sides for air circulation.
5
KTF840_841_WHT_IB_C18.indd 5 19/6/18 1:42 pm
Your Kambrook Tower Fan
1. Touch control panel featuring:
• POWER On/Off button
• Fan SPEED button
(Includes 3 speed settings;
low, medium and high)
• MODE button (includes 3
cooling modes; nature and
reduction mode)
• TIMER button (up to 7 hours)
• OSC button to set oscillation
2. Tower fan body
3. Remote control signal receiver
4. Oscillating platform
5. - KTF840WHT - 1 piece base stand
- KTF841WHT - 2 piece base stand
a and b
6. Remote control with soft
touch buttons
7. Carry handle
8. Remote control storage
9. Detachable filter cover
10. Detachable filter
Not Shown
• 3 screws to secure the base
to the unit
KTF840WHT
base stand
6
6
KTF840_841_WHT_IB_C18.indd 6 19/6/18 1:42 pm
KT F 841WHT
base stand
7
8
9
10
Model KTF841 shown
MODE
OSC
4h
MODE
OSC
4h
MODE
OSC
4h
MODE
OSC
4h
MODE
OSC
4h
Quick Start Guide
Turning the tower fan on
Plug the power cord into a
230V or 240V power point and
switch on.
2h
1h
TIMER
SPEED
POWER
To start the tower fan, turn the
tower fan on by pressing the
‘POWER’ button once.
2h
1h
The unit will be in NORMAL fan
mode, at LOW speed setting.
TIMER
SPEED
POWER
Setting the fan speed
2h
1h
TIMER
SPEED
POWER
Pressing the ‘SPEED’ button
once will set the tower fan into
MEDIUM speed setting.
2h
1h
Pressing the ‘SPEED’ button
twice will set the tower fan into
HIGH speed setting.
TIMER
SPEED
POWER
2h
1h
TIMER
SPEED
POWER
Pressing the ‘SPEED’ button
three times will set the tower fan
into LOW speed setting.
Setting the fan mode Setting the oscillation
OSC
4h
2h
MODE
TIMER
Once the tower fan is switched
on and the ‘POWER’ button
is selected; the unit will be in
NORMAL fan mode.
Pressing the ‘MODE’ button
once will set the tower fan
4h
2h
Pressing the ‘MODE’ button
twice will set the tower fan into
REDUCTION mode. To set the
tower fan back to NORMAL
mode, press the ‘MODE’ button
again.
OSC
MODE
TIMER
OSC
4h
MODE
Pressing the ‘OSC’ button
will allow the tower fan to
oscillate side to side. To stop
the oscillation, press the ‘OSC’
button again.
into NATURE mode.
KTF840_841_WHT_IB_C18.indd 7 19/6/18 1:42 pm
7
Using Your Kambrook Tower Fan
Before first use
Remove your tower fan from its carton
and associated protective wrapping.
Unwind the cord to its full length and
remove any protective cardboard
or foam that may have been used
to minimise transportation damage.
Once assembled by following the
directions below, place the tower
fan on a firm, level surface in a stable
upright position. Visually inspect the air
inlet and outlets to ensure no foreign
material is blocking these areas.
WARNING: When
Unpacking the fan, check
to see you have received
all the items listed in
the parts list, before
discarding the packaging.
Assembling Your Tower Fan
To assemble the KTF840WHT
base stand (1 piece):
1. The tower fan base stand comes
as one piece.
2. To assemble the base stand,
place the tower fan body on
its side. Remove the 3 fastening
screws from underneath the
tower fan section of the fan and
set aside. (See Fig.1).
3. Hold the base stand piece with
the curved side facing towards
the bottom part of the tower fan
body, thread the power cord
through the circle cord opening
located in the base stand piece.
(See Fig.2).
Fig. 2
4. Position base stand piece over
the corresponding screw holes
located underneath the tower
fan body. Press power cord into
the cord clip to keep it secure
(See Fig.3).
Fig. 3
5. Secure base stand piece with 3 of
the fastening screws. (See Fig.4).
Fig. 4
Fig. 1
8
KTF840_841_WHT_IB_C18.indd 8 19/6/18 1:42 pm
6. Return the tower fan to its upright
position; Its now ready for use.
Using Your Kambrook Tower Fan continued
To assemble the KTF841WHT
base stand (2 pieces):
1. The tower fan base stand comes
in two separate pieces that
connect with one another.
2. To assemble the base stand,
place the tower fan body on
its side. Remove the 3 fastening
screws from underneath the
tower fan section of the fan and
set aside. (See Fig. 5).
Fig. 5
3. Holding base stand piece (a)
with the curved side facing
towards the bottom part of the
tower fan body, position base
stand piece (a) screw hole over
the corresponding screw hole
located underneath the tower
fan body. (See Fig 6). Secure
base stand piece (a) with 1 of the
fastening screws. (See Fig. 7.).
a
Fig. 6
a
4. Position base stand piece (b) with
the curved side facing towards
the bottom part of the tower fan
body, onto base stand piece (a)
by interlocking the six locating
posts located along the straight
edge of each of the base stand
pieces and by aligning the two
remaining screw holes located
underneath the tower fan body
with the corresponding screw
holes on base stand piece (b).
Firmly push down base stand
piece (b) until it is secured into
place with base stand piece (a)
(See Fig. 8). Secure base stand
piece (b) with the 2 remaining
fastening screws. (See Fig. 9).
b
a
Fig. 7
Fig. 8
9
KTF840_841_WHT_IB_C18.indd 9 19/6/18 1:42 pm
Using Your Kambrook Tower Fan continued
NOTE: To avoid infrared
interference that may trigger
the operation of the cooling
fan, ensure the fan is positioned
away from other infrared remote
controlled appliances.
Fig. 9
Thread the power cord through the
circle cord opening located in the
base stand piece, pressing into the
cord clip to keep it secure. (See Fig.
10).
WARNING: Make sure the
power cord is not trapped
between the base stand
pieces and tower fan body.
5. Return the tower fan to its upright
position; it is now ready for use.
WARNING: Do not operate
the tower fan without the
base stand fitted.
Fig. 10
Turning Your Tower Fan On
To operate the tower fan, plug the
power cord into a 230V or 240V
electrical outlet and switch the outlet
on. Be sure the plug fits tightly as a
loose fit will cause overheating and
damage the plug.
Once the power outlet is switched
on, the fan is in ‘Standby’. In Standby,
the fan is not turned on and the LED
display will not illuminate.
To turn the tower fan on, press the
‘POWER’ button once; the unit will
be in NORMAL fan mode at LOW
speed setting.
Setting the Fan Speed
The tower fan has three fan speed
settings; LOW
HIGH
Pressing the ‘SPEED’ button once
will set the tower fan into LOW
speed setting.
Pressing the ‘SPEED’ button
twice will set the tower fan into
Medium
Pressing the ‘SPEED’ button three
times will set the tower fan into
HIGH
To turn the tower fan OFF, press the
‘POWER’ button and turn off at the
power outlet and remove the plug
from the power outlet.
.
speed setting.
, MEDIUM and
speed setting.
10
KTF840_841_WHT_IB_C18.indd 10 19/6/18 1:42 pm
Using Your Kambrook Tower Fan continued
Setting the Nature and
Reduction Mode
Your tower fan has a NATURE
and REDUCTION
Both the NATURE
REDUCTION
used on any fan speed. The LED
screen will indicate what mode
the fan has been set in.
setting.
and
modes can be
Nature Mode
The NATURE mode simulates the
natural rise and fall of the wind
over time, with speed settings
automatically cycling between low,
medium and high.
At any fan speed setting, pressing the
MODE button once will turn the tower
fan into NATURE
To turn the NATURE
the MODE button twice, the fan will
now be in NORMAL operation mode.
mode.
mode OFF, press
Reduction mode
The REDUCTION mode allows you to
pre-select a variation in speed which
automatically decreases the fan
speed over time.
The REDUCTION
speed settings.
Once the fan speed is selected, press
the MODE button twice will turn the
tower fan into REDUCTION
To turn the REDUCTION
press the MODE button once, the
fan will now be in NORMAL
operation mode.
mode applies in all
mode.
mode off,
NOTE: When the NATURE mode
setting is selected, the tower fan is
programmed to
self-regulate through the various
fan speeds. The NATURE
independent from the fan speed
settings while the LED screen will
still display the last selected fan
speed setting.
mode is
Setting the Oscillation
This function will work in any mode.
Pressing the ‘OSC’ button will allow
the tower fan to oscillate from side to
side. To stop the unit oscillating, press
the ‘OSC’ button once more.
Setting the Auto-Off Timer
The timer function works in all
operating modes, and switches
the unit into standby mode after a
pre-set number of hours.
• Press the ‘TIMER’ button to
activate the timer settings.
• Press the ‘TIMER’ button to cycle
through the one hour increments,
up to 7 hours.
• The tower fan will then switch itself
to standby mode after the selected
number of hours has passed.
• The TIMER can be set on any of
the settings.
11
KTF840_841_WHT_IB_C18.indd 11 19/6/18 1:42 pm
Using the Remote Control
Before using the remote control,
remove the battery isolating slip
by pulling the slip away from the
remote control. The remote control
buttons operate in the same way
as those on the tower fan control
panel. Your remote control includes
1 x CR2025 3V Lithium battery, and
can be conveniently stored in the
compartment at the rear housing of
the unit.
To replace the battery open up the
battery compartment at the back of
the remote by forming a good grip of
the remote, pushing the small arched
groove to the right and simultaneously
pushing out the battery compartment
cover by pushing the rectangular
groove outwards (See Fig.1a).
Insert the battery paying attention
to the polarity (+ and -). Reinsert the
battery compartment into the remote
control ensuring that the + symbol is
facing upwards when inserted
(See Fig.1b). Make sure the battery
compartment is correctly secured.
Fig. 1a
Fig. 1b
NOTE: To avoid infrared
interference that may trigger
the operation of the cooling
fan, ensure the fan is positioned
away from other infrared remote
controlled appliances.
WARNING - KEEP
BATTERIES OUT OF
REACH OF CHILDREN
Swallowing may lead to serious
injury in as little as 2 hours or
death, due to chemical burns
and potential perforation of the
oesophagus.
If you suspect your child has
swallowed or inserted a button
battery immediately call the
24-hour Poisons Information
Centre on 13 11 26 for fast,
expert advice.
Examine devices and make
sure the battery compartment
is correctly secured, e.g. that
the screw or other mechanical
fastener is tightened. Do not use
if compartment is not secure.
Dispose of used button batteries
immediately and safely. Flat
batteries can still be dangerous.
Tell others about the risk
associated with button batteries
and how to keep their children
safe.
12
KTF840_841_WHT_IB_C18.indd 12 19/6/18 1:42 pm
Care, Cleaning and Storage
1. Ensure that the tower fan is
switched OFF and disconnected
from the power outlet
before cleaning.
2. Use a clean, dry cloth to clean
the external surfaces of the tower
fan. If the tower fan has collected
dirt inside the unit, have the unit
cleaned by a qualified service
agent. Do not operate the tower
fan in this condition.
3. Do not attempt to open the
case of the tower fan at any
time as there are no customer
serviceable parts inside.
4. When not in use, store the tower
fan (preferably in its original box)
in a cool, clean and dry location.
WARNING: Do not operate
the tower fan without the
filter, filter cover and base
stand fitted
WARNING: When
unpacking the fan, check
to see you have received
all the items listed in the
Parts List, before discarding
the packaging.
WARNING: Do not operate
the tower fan without the
base stand fitted
WARNING: Never insert
fingers, pencils or any
other objects through
the guards whenever the
power plug is connected,
in particular while the fan
is switched on.
13
KTF840_841_WHT_IB_C18.indd 13 19/6/18 1:42 pm
Care, Cleaning and Storage
Cleaning the Filter
The filter is located behind the rear
cover of the fan.
To clean the filter:
1. Ensure that the tower fan is
switched OFF and disconnected
from the power outlet before
cleaning.
2. Gently unsnap the rear filter cover
from the tower fan (See Fig. 11)
and remove the filter (See Fig.12).
3. Run the filter under cool water
and gently rub to remove the
accumulation of particles.
4. Once filter has been cleaned let
it dry completely before placing
back onto the tower fan.
5. Once the filter is completely dry,
replace the filter and firmly snap
rear filter cover back in place
(See Fig 13.)
NOTE: remember to clean the
filter regularly.
Fi g . 11 Fig. 12
Fi g. 13
WARNING: Do not put
the filter in a dishwasher,
washing machine, tumble
dryer, oven, microwave or
near a naked flame.
14
KTF840_841_WHT_IB_C18.indd 14 19/6/18 1:42 pm
Notes
15
KTF840_841_WHT_IB_C18.indd 15 19/6/18 1:42 pm
Kambrook - Australia
Ground Floor, Suite 2, 170-180 Bourke Rd
Alexandria NSW 2015, Australia
Kambrook - New Zealand
Private Bag 94411
Botany, Manukau
Auckland 2163
Locked Bag 2000
Botany NSW 1455
Customer Service Line 1300 139 798
Customer Service Fax 1800 621 337
www.kambrook.com.au
Due to continual improvement in design or otherwise, the product you
purchase may differ slightly from the illustration in this book. Issue C18
KTF840_841_WHT_IB_C18.indd 16 19/6/18 1:42 pm
New Zealand
Customer Service Line/
Spare Parts 0800 273 845
Customer Service Fax 0800 288 513
www.kambrook.co.nz
Loading...