Page 1
12
Kambrook warrants the purchaser against defects in workmanship and material for a period of 12 months
from the date of purchase (3 months commercial use).
Guarantee and purchase receipt for this product are to be retained as proof of purchase and must be
presented if making a claim under the Kambrook guarantee.
Kambrook reserves the right to replace or repair the appliance within the warranty period.
Warranty does not apply to any defect, deterioration, loss, injury or damage occasioned by, or as a result
of the misuse or abuse, negligent handling or if the product has not been used in accordance with the
instructions. The guarantee excludes breakages and consumable items such as kneading blades.
This warrant y is void if there is evidence of the product being tampered with by unauthorised persons.
If the product includes one or a number of accessories only the defective accessory or product will be
replaced. In the event of Kambrook choosing to replace the appliance, the guarantee will expire at the
original date, i.e. 12 months from the original date of purchase.
In Australia, this KAMBROOK Guarantee is additional to the conditions and guarantees which are mandatory
as implied by the Trade Practises Act 1974 and State and Territory legislation.
For service, spare parts or product information in Australia, please call KAMBROOK on the Customer
Service Line; 1300 139 798.
For service, spare parts or product information in New Zealand, please call KAMBROOK on the Customer
Service Line; 0800 273 845 or 09 271 3980.
If claiming this guarantee the product must be returned freight prepaid.
KAMBROOK 12 MONTH REPLACEMENT WARRANTY
YOUR PURCHASE RECORD (Please complete)
DATE OF PURCHASE .......................................................
MODEL NUMBER .............................................................
SERIAL NUMBER .............................................................
PURCHASED FROM .........................................................
Attach a copy of the purchase receipt here.
(Please don’t return purchase record
until you are making a claim)
Due to continual improvement in design or ot herw ise, t he product you purchase may dif fer sligh tly from the illus trat ion in t his book. Issue 1/09
KAMBROOK 12 MONTH REPLACEMENT WARRANTY
Register your warranty at www.kambrook.com.au/service.asp
Kambrook - Australia
Building 2, Port Air Industrial Estate
1A Hale Street
Botany NSW 2019
Australia
Customer Service Line 1300 139 798
Customer Service Fax 1800 621 337
Kambrook - New Zealand
Private Bag 94411
Greenmount, Manukau
Auckland 2141
New Zealand
Customer Service Line/Spare Parts 0800 273 845
or 09 271 3980
Customer Service Fax 0800 288 513
Page 2
CaptivG3Lift
Cyclonic
Bagless Vacuum
KBV220/280
Instruction Booklet
Page 3
2
• Carefully read all instructions before operating the
Kambrook CaptivG3Lift Cyclonic Bagless Vacuum
for the first time and save for future reference.
• To protect against electric shock, do not immerse
the vacuum, cord or plug in water or any other
liquid.
• Ensure that the power source to be used is the
same as the voltage requirements of the product.
• Always switch vacuum cleaner to off, then
switch off at the power outlet, and then unplug
the vacuum cleaner when not in use and prior to
cleaning the dust container or filters.
• Never use the vacuum cleaner without a dust
container and motor protection filter in place.
• Never use the vacuum cleaner to vacuum hot
ashes, broken glass, sharp objects or liquids.
• Never use in the presence of explosive liquids or
vapours.
• Never vacuum up inflammable or poisonous
liquids such as petrol, copier toner or other volatile
substances. Never vacuum up acids, asbestos or
asbestos dust.
• Do not leave the vacuum cleaner unattended
when in use. Young children should be supervised
to ensure that they do not play with the vacuum
cleaner.
• Close supervision is required at all times when
operating the vacuum cleaner near children.
• This vacuum cleaner is suitable for domestic use
only. Do not use this vacuum cleaner for anything
other than its intended use.
• Do not use or store outdoors.
• Fully extend the cord (to the yellow tape mark)
whenever the vacuum cleaner is in use. Please
ensure that the cord is not extended past the red
tape mark.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety.
• Do not leave the appliance unattended when in
use.
• Children should be supervised to ensure that they
don’t play with the appliance.
• Regularly inspect the supply cord, plug and
actual appliance for any damage. If damage is
found in any way, immediately cease use of the
appliance and return the entire appliance to your
nearest authorised Kambrook service centre for
examination, replacement or repair.
• The installation of a residual current device (safety
switch) is recommended to provide additional
safety protection when using electrical appliances.
It is advisable that a safety switch with a rated
residual operating current not exceeding 30mA
be installed in the electrical circuit supplying the
appliance. See you electrician for professional
advice.
KAMBROOK RECOMMENDS SAFETY FIRST
At Kambrook, we believe that safe performance is the first priority in any consumer product,
so that you, our valued customer can confidently use and trust our products. We ask that any
electrical appliance that you use be operated in a sensible fashion with due care and attention
placed on the following important operating instructions.
IMPORTANT SAFEGUARDS FOR YOUR KAMBROOK CAPTIVG3LIFT CYCLONIC BAGLESS VACUUM
Page 4
3
• Fully unwind the power cord before use.
• Do not let the power cord hang over the edge of
a bench or table, touch hot surfaces or become
knotted.
• The appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of
the appliance by a person responsible for their
safety.
• Children should be supervised to ensure that they
do not play with the appliance.
• It is recommended to regularly inspect the
appliance. To avoid a hazard do not use the
appliance if power cord, power plug or appliance
becomes damaged in any way. Return the entire
appliance to the nearest authorised Kambrook
Service Centre for examination and/or repair.
• Any maintenance other than cleaning should be
performed at an authorised Kambrook Service
Centre.
• This appliance is for household use only. Do not
use this appliance for anything other than its
intended use. Do not use in moving vehicles or
boats. Do not use outdoors. Misuse may cause
injury.
• The installation of a residual current device (safety
switch is recommended to provide additional
safety protection when using electrical appliances.
It is advisable that a safety switch with a rated
residual operating current not exceeding 30mA
be installed in the electrical circuit supplying the
appliance. See your electrician for professional
advice.
IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES
Page 5
4
KNOW YOUR KAMBROOK CAPTIVG3LIFT CYCLONIC BAGLESS VACUUM
1
Bagless convenience, for easy removal of dirt
and dust with no need for replacement bags
2
Variable power control
3
1500 watt motor for superior suction, fast and
effective cleaning
4
Dust level indicator
5
Quality multi-terrain floor tool ideal for carpet
and hard floors
6
Hard floor tool for improved pick up on hard
floors (KBV280 only)
7
Telescopic chrome steel wand is easily
extendable or retractable for varying height
requirements
8
Cyclonic cone helps separate particles from
the air before filtering begins
9
Two washable HEPA filters included
10
Auto cord rewind
11
Convenient carry handle
12
Cord length 5m
13
Small brush
14
Upholstery tool
15
Crevice tool
1
7
3
5
2
10
11
12
8
13
14
15
6
9
4
Page 6
5
OPERATING INSTRUCTIONS
BEFORE FIRST USE
Remove any promotional material from the vacuum
cleaner.
When unpacking the vacuum cleaner check to see
you have received all the required components,
such as the hose and other accessories before
discarding the packaging.
TO OPERATE THE VACUUM CLEANER
Locate the crush proof hose and push the
connection point into the hose inlet connection on
the front side of the vacuum, until a “click” sound
is heard.
Connect the wide end of the metal wand to the
hose end, and push together firmly.
Fit the floor tool to the narrow end of the wand and
push together firmly.
Fully extend the power cord by pulling the power
plug out from the rear of the vacuum, until the
yellow tape on the cord is showing.
NOTE: Ensure that you do not over extend the
power cord – do not extend past the red warning
tape on the cord.
Plug into a 230/240V power point and switch the
power on at the power point.
To commence vacuuming, push down on the on/off
button
up
down
on the top of the vacuum cleaner.
When vacuuming is complete, push down on the
‘on/off’ button to switch off. Turn the power off at
the outlet and then remove the power cord from
the power outlet. When removing the plug from the
power outlet, grasp the plug not the cord.
To retract the cord push down on the ‘cord rewind’
button
up
down
on top of the vacuum cleaner.
IMPORTANT: HOLD THE PLUG END AND GUIDE THE CORD
INTO THE VACUUM DURING RETRACTION TO PREVENT IT FROM
STRIKING YOU OR THE VACUUM.
CAUTION: ALWAYS ENSURE THAT THE DUST CONTAINER
AND THE MOTOR PROTECTION FILTER ARE CORRECTLY FITTED.
NEVER OPERATE WITHOUT THE DUST CONTAINER OR FILTERS
IN PLACE.
VARIABLE POWER CONTROL
The power booster lever on the vacuum can be
used for variable power control. Slide the lever
toward the MAX marking for vacuuming hard floor
and carpet surfaces. Slide the lever toward the
MIN marking when using the crevice, upholstery
and brush tools.
Page 7
6
CREVICE AND BRUSH TOOL
ACCESSORIES
The crevice tool is ideal for vacuuming hard to
reach places such as the edges along skirting
boards.
The brush and upholstery tools can be used to
vacuum delicate surfaces and areas such as
shelves and venetian blinds.
Set the variable speed control between minimum
and medium power when using the tool
accessories.
Turn off the vacuum cleaner when changing any
attachments.
HARD FLOOR TOOL (KBV280 ONLY)
The hard floor tool is ideal for vacuuming hard
floors, with improved pick-up.
Simply fit the hard floor tool to the narrow end of
the wand and push together firmly.
Turn off the vacuum cleaner when changing any
tools. Follow the ‘TO OPERATE THE VACUUM
CLEANER’ instructions to commence vacuuming.
CARE AND MAINTENANCE
Check all filters and replace them regularly. It is
recommended to clean the filters after every use.
For normal household vacuuming the filters should
be replaced at least twice a year.
If you encounter reduced vacuum cleaner
performance, check:
• Dust capacity in dust container
• All filters, including dust, motor and exhaust. Any
clogging in the filters will reduce the efficiency of
your vacuum cleaner
To clean the outside of the unit, wipe the exterior
with a soft, damp cloth. Never use an abrasive
cleaner.
EMPTYING THE DUST CONTAINER
Always switch the vacuum off, then switch off
at the power outlet and unplug prior to replacing
filters or emptying the dust container.
For optimum use, the dust container should be
emptied after every use. When the dust container
Page 8
7
reaches the capacity mark ‘MAX’, it is essential to
thoroughly clean both the dust container and filters.
To remove the dust container, ensure the vacuum
is down on its wheels; remove the dust container
by pressing down on the button on top of the dust
container. Once released carefully lift the container
upwards.
To empty the dust container simply place it over
the rubbish bin, ensuring the opening of the bin is
larger than the dust container. Press the “PUSH”
button located beneath the hose inlet connection
on the front of the dust container. The bottom of the
container will release and the dust and compiled
dirt will be dispensed.
NOTE: Dependant upon the amount and type of dirt
collected in the dust container, it may be necessary
to agitate the dirt inside the dust container for
easier dispensing.
IMPORTANT: DO NOT USE THE UNIT WITHOUT A DUST
CONTAINER IN PLACE.
CLEANING AND REPLACING FILTERS
To assist you with the regular care of your vacuum,
a second HEPA filter is supplied for convenient use,
ideal for when a dirty filter is being cleaned.
Dirty and clogged filters may result in reduced
suction performance. It is recommended that filters
are cleaned after every use and replaced regularly
to ensure maximum efficiency from your vacuum.
If filters are left uncleaned, it may result in a
reduction of suction power. Should this occur, the
following procedure should be followed every
couple of months.
PROCEDURE TO REPLACE FILTERS
Always switch the vacuum off, then switch off at
the power outlet and unplug prior to cleaning or
replacing the filters. Before replacing the filters
ensure all dirt and dust is first emptied from the
dust container. Refer to the ‘EMPTYING THE DUST
CONTAINER’ section.
1. Remove the dust container from the vacuum
by pressing down on the button on top of the
dust container. Once released, carefully lift the
container upwards.
2. To remove the HEPA filter from the back (flat
side) of the dust container, press the tab and
pull out the HEPA filter, followed by the foam
filter.
Page 9
8
3. Shake and tap the HEPA filter until all the fine
dust particles are removed. After approximately
6 months the HEPA filter should be replaced.
This period is dependant upon the frequency
of use and type of dirt being subjected to the
vacuum.
The HEPA filter can also be hand washed in
warm water.
NOTE: Do not use any detergents or boiling water
to wash the filter, do not wash the filter in a
dishwasher or washing machine.
It is advised to let the filter dry completely for at
least a minimum of 24 hours before use.
NOTE: Do not dry in a tumble dryer, microwave,
oven or near a naked flame. The filter and filter case
must be completely dry before replacing into the
vacuum. Failure to allow the filter to completely dry
may result in damage to the vacuum motor.
NOTE: A second hepa filter is supplied for
convenience, ideal for when a used filter is being
cleaned.
4. To place the filter back in the dust container,
ensure that the filter is completely dry before
use. Close the bottom of the container.
5. Simply place the foam filter into the back of the
HEPA filter and then click the filter assembly
into the back of the dust container.
6. To remove and clean the CaptivG3 cone from
inside the dust container, firstly ensure the
dust container has been emptied. Follow
the ‘EMPTYING THE DUST CONTAINER’
instructions.
Press the ‘PUSH’ button located beneath the
hose inlet connection on the front of the dust
container. The bottom of the container will
release. Grip the two pockets at the base of the
cone with two fingers, twist anti-clockwise to
‘OPEN’ and pull to remove the cone.
Shake and tap the cone until all the fine dust
particles are removed. The cone can also be
hand washed. Allow the cone to completely air
dry before re-assembling.
To replace the cone into the dust container, grip
the two pockets at the base of the cone with
two fingers, slide the cone into the allocated
bracket inside the dust container and twist
clockwise to ‘CLOSE’ until resistance is felt.
Page 10
9
7. Place the dust container back in the vacuum
cleaner for next use.
ExHAUST FILTER
The exhaust filter should be cleaned every six
months. Simply unclip the grill on the top of the
vacuum cleaner towards the rear, shake and tap
the filter to remove any dust accumulated. Then
relocate the filter and reattach the grill.
CARE AND MAINTENANCE
Always switch the vacuum off, then switch off at
the power outlet and unplug the appliance prior to
cleaning or replacing either filter.
To clean the outside of the unit, wipe the exterior
with a soft, damp cloth. Never use an abrasive
cleaner.
IMPORTANT: CHECK AND REPLACE bOTH THE MOTOR
PROTECTION AND HEPA FILTERS APPROxIMATELY TWICE A
YEAR OR WHEN VISIbLY CLOGGED.
Page 11
10
TROUBLE SHOOTING GUIDE
PROBLEM POSSIBLE CAUSES WHAT TO DO
Vacuum cleaner is not working
• The unit may not be plugged
into power outlet
• Ensure the power plug is
securely plugged
Vacuum cleaner is not picking
up dirt
• Dust container is full
• Filter is clogged
• Dust container is not fitted
correctly
• Empty and clean the dust
container
• Refer to ‘Cleaning and
Replacing Filters’, page 7
• Check dust container
replacement
Dust escaping from vacuum
• Dust container is not fitted
correctly
• Hose is not fitted correctly
• Dust container is full
• Check dust container
installation
• Check hose installation
• Empty and clean the dust
container
SPARE PARTS
To order spare parts for your Kambrook CaptivG3Lift Cyclonic Bagless Vacuum
please contact Customer Service on:
1300 139 789 (Australia)
and 0800 253 007 (New Zealand)
Page 12
11
NOTES
Loading...