KAM KWM1960 V2 Instruction Manual

MADE IN CHINA

UHF receiver Handheld microphone transmitters

16 UHF frequencies from 863.0 to 865.0 MHz Steel metal grille
Balanced output sockets (3-pin XLR) Transmitter power: 10mW
Unbalanced 6.3mm jack for mixed audio output Modulation type: FM
Twin adjustable antenna system Max deviation: ±25KHz
Frequency stabilisation: <±30ppm Spurious emission: >40dB
Dynamic range: >90dB Mic battery voltage: 3V (2 x 1.5V AA batteries)
Total harmonic distortion: <0.5% Continuous usage: 5 hours
Frequency response: 40Hz-15KHz ±3dB Working distance: 50m
S/N ratio: >90dB Dimensions: 55 x 55 x 260mm (WxDxH)
Image and spurious rejection: >80dB Bodypack transmitters
Border upon channel rejection: >80dB Easy access on/off switch / battery indicator
Receiving sensivity: 5dBuV Illuminated display
De-emphasis: 75uS Mic battery voltage: 3V (2 x 1.5V AA batteries)
Receiver power supply DC 17V 300mA Continuous usage: 5 hours
Power consumption: 5W Working distance: 50m
Dimensions: 210 x 185 x 45mm (WxDxH) Dimensions: 160 x 35 x 65mm (WxDxH)

MANUAL VERSION 1.0

10- 01- 16

Due to continuous product development, please ensure that you have downloaded

the latest instruction manual for this product from the Kam website:

www.kam.co.uk

Kam products are manufactured by: Lamba plc, Unit 1, Southfields Road, Dunstable, Bedfordshire, United Kingdom LU6 3EJ

Telephone: (+44) (0)1582 690600 • Fax: (+44) (0)1582 690400 • Email: [e-mail] • Web: www.lambaplc.com

Due to continuous product development, specifications and appearance are subject to change. © Copyright Lamba plc. E&OE.

KWM1960 V2

UHF wireless microphone / bodypack systems

Thank you for purchasing this Kam product, we are sure that it will serve you for many years to come.

To optimise the performance of this product, please read these operating instructions carefully to familiarise yourself
with the basic operations of this unit. Please retain them for future reference.This unit has been tested at the factory
before being shipped to you.

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. To prevent a fire
hazard, do not expose the unit to any naked flame sources. Unplug this apparatus during lightning storms or if it is
unlikely to be used for long periods of time. When installing the unit, please ensure you leave enough space around
the unit for ventilation. Slots and openings in the unit are provided for ventilation to ensure reliable operation of the
product and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered.

The unit is mains powered, always handle the power cable by the plug. Never pull out the plug by pulling on the
cable. Never touch the power cable when your hands are wet as this could cause an electric shock. Do not tie a knot
in the cable. The power cable should be placed such that it is not likely to be stepped on. A damaged power cable
can cause a fire or give you an electrical shock. Check the power cord periodicaly, if you ever find that it is
damaged, replace it before using the unit again. Contact your retailer for a replacement.

The voltage of the available power supply differs according to country or region. Be sure that the power supply
voltage of the area where this unit is to be used meets the required written on the unit.

The lightning flash symbol inside a triangle is to alert the user to the presence high voltage within the unit’s
enclosure that may be of sufficient power to constitute a risk of electrical shock to persons.
Caution: to prevent the risk of electric shock, do not attempt to open the unit. No user-serviceable parts
inside. Refer all servicing to qualified service personnel.
The exclamation mark inside a triangle is intended to alert the user to the presence of important operating
and maintenance instructions in the literature accompanying the appliance.

Select the installation location of your unit carefully. Avoid placing it in direct sunlight or locations subject to vibration
and excessive dust. Do not use the unit where there are extremes in temperature (below 41ºF / 5ºC or exceeding
95ºF / 35ºC).

Unpacking and safety Please unpack your new product carefully. Your new product should reach you in perfect
condition. Please check that no damage has occurred during transit. If any damage is found, do not operate your
unit. Please contact the retailer you purchased it from immediately. If there is any damage to the mains cable do not
use the device. Always disconnect the unit from the mains supply when carrying out any cleaning of the unit.

Manufacturer declarations

In compliance with the following requirements: RoHS Directive (2002/95/EU) and WEEE Directive (2002/96/EU),
and Battery Directive (2006/66/EU). If this product is ever no longer functional please take it to a recycling plant for
environmentally friendly disposal. Any supplied batteries can also be recycled.

CE declaration of conformity

R&TTE Directive (1999/5/EU), EMC Directive (2004/108/EU),Low Voltage Directive (2006/95/EU).
The declarations are available on application from [e-mail]

Before putting device into operation, please observe the respective country-specific regulations.

IMPORTANT
Kam KWM1960 V2 systems use 16 UHF frequencies from 863.0 to 865.0 MHz.

Systems are available with handheld microphones or bodypacks (including headset mic, lavalier/lapel mic and
guitar/instrument lead). If you have purchased the optional Kam BP1960 V2 Kit, you will also need a Kam
KWM1960 V2 receiver (not included in the BP1960 V2 Kit) to operate and receive signals from your bodypack.