Jwin JV-DTV23, JV-DTV27, JV-DTV30 User Manual
JV-DTV23 / JV-DTV27 / JV-DTV30
Please read this manual carefully before operating your set. Retain it
for future reference.
See the label attached on the back cover and quote this information to
your dealer when you require service.
JV -DTV 23 / 2 7 / 30 V 10 M 1 0 / E N / F R / GE/ I T / S P 05 11 2 0 05
Installation 3
Remote control handset 4-5
Controls 4
Battery installation 5
Controls of
Front panel 6
Connections of
Back panel 7
Connection to
External equipment 8-11
Basic operation
On and Off 12
Programme selection 12
Volume adjustment 12
On screen language selection (option) 12
On screen menus
Menu selection 13
Picture adjustment 14-15
PSM (Picture Status Memory) 14
Manual Picture Control 14
Picture Format 15
Sound adjustment 16-18
SSM (Sound Status Memory) 16
Balance 17
AVL (Auto Volume Leveler) 17
Stereo/Dual/NICAM reception 18
Setting up TV stations 19-24
Auto programme tuning 19
Manual programme tuning 20-21
Programme edit 22-23
Calling the programme table 24
Time Menu / Other functions 25-26
Clock 25
On/Off Time 25
Auto sleep / Sleep timer 26
CSM (Colour Status Memory) 26
Connection of PC
PC Setup 27
PIP (Picture-In-Picture) Feature 28-29
Watching PIP 28
Moving the PIP 28
Swapping the PIP 29
Selecting a Input Signal Source for the PIP 29
Programme selection for sub picture 29
Programme scan 29
Teletext (option) 30-31
External Control Device Setup 32-39
Displayable Monitor Specification 40
Troubleshooting
Check list 43
Contents
2
Power
This set operates on an AC mains supply, the voltage is as
indicated on the label on the back cover. Never apply DC
power to the set. In the event of thunderstorms or powercuts, please pull out the aerial and mains plugs.
Warning
To prevent fire or shock hazard, do not expose the set to
rain or moisture. Do not rub or strike the Active Matrix LCD
with anything hard as this may scratch, mar, or damage the
Active Matrix LCD permanently.
Service
Never remove the back cover of the set as this can expose
you to very high voltage and other hazards. If the set does
not operate properly, unplug it and call your dealer.
Aerial
Connect the aerial cable to the socket marked +75 Ω on
the back cover. For the best reception an outdoor aerial
should be used.
Location
Position your set so that no bright light or sunlight falls
directly onto the screen. Care should be taken not to
expose the set to any unnecessary vibration, moisture,
dust or heat. Also ensure that the set is placed in a position to allow a free flow of air. Do not cover the ventilation
openings on the back cover.
Cleaning
Unplug the set before cleaning the face of the LCD Screen.
Dust the set by wiping the screen and the cabinet with a
soft, clean cloth. If the screen requires additional cleaning,
use a clean, damp cloth. Do not use liquid cleaners or
aerosol cleaners.
Installation
3
EN
- All the functions can be controlled with the remote control handset.
- Some functions can also be adjusted with the buttons on the front panel of the set.
POWER
switches the set on from standby or off to
standby.
NUMBER BUTTONS
PSM (Picture Status Memory)
recalls your preferred picture setting.
LIST
displays the programme table.
MENU
selects a menu.
EXIT
exits from each mode.
TELETEXT BUTTONS (option)
These buttons are used for teletext.
For further details, see the ‘Teletext’ sec-
tion.
PIP
Switches the sub picture on or off.
PIP PR +/-
Selects a program for the sub picture.
SWAP
Alternates between main and sub picture.
PIP INPUT
Selects the input mode for the sub pic-
ture.
PIP POSITION
relocates the sub picture in clockwise
direction.
STILL
freezes motion of the sub picture.
SCAN
switches on the programme scan mode
through 4/12 sub pictures.
MUTE
switches the sound on or off.
ARC
select your desired picture format.
SSM (Sound Status Memory)
recalls your preferred sound setting.
I/II
selects the language during dual language
broadcast.
selects the sound output (option).
INPUT SELECT
Select TV, AV1, AV2, SAV, COMPONENT,
RGB-DTV, RGB-PC, RGB-DVI mode.
DD/ EE
(Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
FF / GG (Volume Up/Down)
adjusts the volume.
adjusts menu settings.
OK
accepts your selection or displays the
current mode.
PC/DVI
selects COMPONENT, RGB-DTV, RGB-PC,
RGB-DVI mode.
SLEEP
sets the sleep timer.
Q.VIEW
returns to the previously viewed programme.
- COLOURED BUTTONS
These buttons are used for teletext (only
TELETEXT models) or programme edit.
Remote control handset
Controls
Before you use the remote
control handset, please
install the batteries.
4
i
?
REVEAL
MIX
INDEX
TIME
PIP PR+ PIP PR- SWAP
PIP INPUT
PIP
PIP POSITION
STILL
SCAN
UPDATE
MODE
SIZE
HOLD
MENU
INPUT SELECT
SLEEP
VOL
VOL
PR
OK
1
3
4 6
7 9
2
5
8
0
I / II
ARC
LIST
EXIT
PR
TEXT
PC/DVI
Q.VIEW
X
M
PSM
POWER
SSM
EN
- Your remote control handset is powered by two AAAtype batteries.
To insert batteries, turn the remote
control handset over and remove the
battery cover.
Remote control handset
Battery installation
5
1
1
Put the two batteries into the compartment observing battery polarity.
2
2
Replace the cover.
To avoid damage from possible battery leakage, remove the batteries if
you do not plan to use the remote control handset for an extended period
time. Do not use batteries of differing
age or type. Always discard of batteries safely.
3
3
1. MAIN POWER
switches the set on or off.
2.
DD / EE
(Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
3.
FF / GG (Volume Down/Up)
adjusts the volume.
adjusts menu settings.
4. MENU
selects a menu.
5. INPUT SELECT
selects
TV, AV1, AV2, S-Video, Component,
RGB-DTV, RGB-PC, RGB-DVI mode.
switches the set on from standby.
6. POWER (I /
rr )
switches the set on from standby or off to
standby.
7. POWER/STANDBY INDICATOR (rr)
illuminates red in standby mode.
illuminates green when the set is switched on.
8. REMOTE CONTROL SENSOR
(Front panel)
Controls of
Front panel
6
1
4 5 6 7 82 3
1. RGB INPUT / AUDIO INPUT / DVI INPUT SOCKETS
Connect the set output socket of the PERSONAL COM-
PUTER to this socket.
2. RS-232C INPUT(CONTROL/SERVICE) PORT
Connect to the RS-232C port on a PC.
3. AUDIO INPUT / COMPONENT INPUT (480i/480p/720p/
1080i) SOCKETS
4. S-VIDEO INPUT
connect video out from an S-VIDEO VCR to the SVIDEO input.
EURO SCART SOCKET
connect the euro scart socket of the VCR to these sockets.
5. AERIAL SOCKET
6. POWER CORD SOCKET
This set operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the set on DC power.
Connections of
Back panel
7
EN
RGB INP UTRGB INP UT
AUDI O I NPU TAUDI O I NPU T
DVI INP UTDVI INP UT
RS-2 32C IN PUTRS-2 32C IN PUT
(CON TRO L/S ER(CONTR OL/ SERV ICE )VICE)
S-VI DEOS-VI DEO
AAV1V1
AAV2V2
AUDIO INPUTAUDI O INPU T
AUDIOAUD IO
RR TT
COMPON ENT COMPON ENT INPU T INPU T
(480i/4 80p/720 p/1080i )( 480i/48 0p/720p /1080i)
YY PPbbPP
rr
ANTANT. IN. IN
AC I NPU TAC INP UT
1 2 3 4 5 6
- You can connect additional equipment, such as VCRs, camcorders etc. to your set. However please check with your
manufacturers instruction books for specific information. Make sure all connections are made with both your set and
additional appliance unplugged from the mains to avoid damaging your equipment. Here shown may be somewhat different from your set.
Connect the RF out socket of the VCR to
the aerial socket on the back of the set.
Connect the aerial cable to the RF aerial
in socket of the VCR.
Store the VCR channel on a desired programme number using the ‘Manual programme tuning’ section.
Select the programme number where
the VCR channel is stored.
Press the PLAY button on the VCR.
Connect to Aerial socket
- If you connect an S-VIDEO VCR to
the S-VIDEO input, the picture
quality is improved; compared to
connecting a regular VCR to the
Video input.
- To avoid picture noise (interfer-
ence), leave an adequate distance
between the VCR and set.
Use the INPUT SELECT button on the remote control to select
AV1 or AV2.
(If connected to S-VIDEO, select the
S-Video external input source.)
Insert a video tape into the VCR and press the PLAY button on the VCR. (See
VCR owner’s manual)
Watching VCR
Connection to
External equipment
8
S-VIDEOS-VIDEO
AAV2V2
ANTANT. IN. IN
AC INPUTAC INPUT
VCR
S-VIDEO
OUT
IN
(R) AUDIO (L ) VID EO
S-V ID EOS-V ID EO
AAV1V1
AAV2V2
ANTANT. IN. I N
AC IN PUTAC IN PUT
1
1
2
2
< Back panel of the set >
< Back panel of VCR >
EN
Connection to
External equipment
9
- After subscribing for a local cable TV station and installing a converter you can watch cable TV.
- For further information of cable TV, contact the local cable TV
station.
In using connection 1
Select programme number in programme switch of cable box.
Match the set programme with selected programme of cable box.
Select your desired programme with the remote control for cable
box.
In using connection 2
Use the INPUT SELECT button on the remote control and select
AV1 or AV2.
Tune to cable service provided channels using the cable box.
Cable
TV
(R) AUDIO (L) VIDEO
VCR
RF
DVI INPU TDVI INPU T
RS- 232C INPUTRS- 232C INPUT
(CO NTROL /SER(CO NTROL/S ERVIC E)VIC E)
S-V IDEOS-VID EO
AAV1V1
AAV2V2
AUDIO INP UTAUDIO INP UT
AUDIOAUDIO
RR TT
COMPO NENT COMP ONENT INPUT INPUT
(480i/ 480p/ 720p/ 1080i )(480i/ 480p/ 720p/ 1080i )
YY PPbbPP
rr
ANTA NT. IN. IN
AC INPUTAC INPU T
S-V IDEOS-VID EO
AAV1V1
AAV2V2
ANTA NT. IN. IN
AC INPUTAC INPU T
Cable
TV
(R) AUDIO (L) VIDEO
VCR
RF
Watching Cable TV
3
3
When connecting the set to an external source,
match the colours of AUDIO/VIDEO input jacks on
the set with the output jacks on the audio/video
equipment: Video = yellow, Audio (Left) = white,
Audio (Right) = red.
Use the INPUT SELECT button on the remote control to select
AV1 or AV2.
Operate the corresponding external equipment.
See external equipment operating guide.
R L
AUDIO VIDE O
S-VIDEOS-VIDEO
AAV1V1
AAV2V2
ANTAN T. IN. IN
AC INPUTAC INPUT
Watching external AV source
4
4
For cable TV
< Cable Box >
< Back panel of the set >
< Back panel of the set >
Camcorder
Video game set
< Back panel of the external
equipment >
2
1
• Component Input ports
You can get better picture quality if you connect DVD player with component input ports
as below.
Connection to
External equipment
10
How to connect
Connect DVD video inputs to Y, PB, PR of COMPONENT (DVD INPUT) and audio inputs to Audio sockets of AUDIO
INPUT.
How to use
Turn on the DVD player, and insert a DVD.
Use INPUT SELECT or PC/DVI button on the remote control to select
Component. Refer to the DVD player's man-
ual for operating instructions.
Watching DVD
DVI INPUT
RS-232C INPUT
(CONTROL/SERVICE)
S-VIDEO
AV1
AV2
AUDIO INPUT
AUDIO
R T
COMPONENT INPUT
(480i/480p/720p/1080i)
Y PbP
r
ANT. IN
AC INPUT
RS-232C INPUT
(CONTROL/SERVICE)
AV1
AV2
AUDIO INPUT
AUDIO
R T
COMPONENT INPUT
(480i/480p/720p/1080i)
Y P
b
P
r
B
R
(R) AUDIO (L)
RS-232C INPUT
(CONTROL/SERVICE)
AV1
AV2
AUDIO INPUT
AUDIO
R T
COMPONENT INPUT
(480i/480p/720p/1080i)
Y P
b
P
r
(R) AUDIO (L)
S-VIDEO
5
5
< Back panel of the set >
< Back panel of a DVD player >
or
Component ports of the
set
Y PB
PR
Video output ports
of DVD player
Y
Y
Y
Y
Pb
B-Y
Cb
P
B
Pr
R-Y
Cr
P
R
EN
Connection to
External equipment
11
Connect the signal cable from the monitor output socket of the PERSONAL COMPUTER to the RGB INPUT socket of
the set.
Connect the audio cable from the PC to the AUDIO INPUT sockets of the set.
Press the INPUT SELECT or PC/DVI button to select
RGB.
Switch on the PC, and the PC screen appears on the set.
The set can be operated as the PC monitor.
Connecting PC
RGB INPUTRGB INPUT
AUDIO INPUTAUDIO INPUT
AUDIO INPUTAUDIO INPUT
AUDIOAUDIO
RR TT
6
6
Press the FF / GG button to
adjust the volume.
If you want to switch the
sound off, press the MUTE
button.
You can cancel it by pressing the MUTE,
FF / GG, SSM
or I/II button.
You can select a programme
number with the
DD / EE
or
NUMBER buttons.
Press the main power button to switch the set on.
If the set is in standby mode,
press the POWER,
DD / EE
,
INPUT SELECT, PC/DVI or
NUMBER buttons on the
remote control handset to
switch it on fully.
Press the POWER button
on the remote control handset.
The set reverts to standby
mode.
Press the main power button again to switch the set
off.
Basic operation
12
1
1
On and Off
2
2
Programme selection
3
3
Volume adjustment
Press the MENU button and
then use
DD / EE
button to
select the SPECIAL menu.
Press the
GG button and then
use
DD / EE
button to select
Language.
Press the
GG button and then
use
DD / EE
button to select
your desired language.
All the on screen displays
will appear in the selected
language.
Repeatedly press the MENU
button to return to normal TV
viewing.
4
4
On screen language
selection (option)
EN
- The dialogue between you and your set takes place on screen with an operator menu. The buttons required for the
operating steps are also displayed.
Press the MENU button
and then use
DD / EE
button
to display each menu.
On screen menus
Menu selection
13
1
1
Press the GG button and
then use
DD / EE
button to
select a menu item.
2
2
Press the GG button to dis-
play the sub menu or the
pull-down menu.
3
3
Change the setting of an
item in the sub or pulldown menu with FF / GG or
DD / EE
.
You can move to the higher level menu with
FF button
and to move to the lower
level menu press the
GG
button.
4
4
PICTURE
()OO}{OOOKOOMENU
PSM
Contrast
Brightness
Colour
Sharpness
SOUND
()OO}{OOOKOOMENU
SSM
Balance
AVL
STATION
()OO}{OOOKOOMENU
Auto
Manual
Edit
TIME
()OO}{OOOKOOMENU
Clock
Off Time
On Time
Auto Sleep
SPECIAL
()OO}{OOOKOOMENU
Language
CSM
PC Control
WXGA
Set ID
Picture adjustment
14
Press the MENU
button and then use
DD / EE
button to
select the PICTURE
menu.
Press the GG button
and then use
DD / EE
button to select
PSM.
Press the
GG button
and then use
DD / EE
button to select a
picture setting on
the
PSM pull-down
menu.
1
1
Repeatedly press the MENU button to return to normal TV viewing.
You can also recall a desired picture (
Dynamic, Standard, Mild
or User) with PSM button on the
remote control. The picture
Dynamic, Standard and Mild
are programmed for good picture
reproduction at the factory and
cannot be changed.
PSM (Picture Status Memory)
2
2
Manual Picture Control
PICTURE
()OO}{OOOKOOMENU
PSM
Contrast
Brightness
Colour
Sharpness
PICTURE
()OO}{OOOKOOMENU
PSM
Contrast
Brightness
Colour
Sharpness
PICTURE
()OO}{OOOKOOMENU
Dynamic
Standard
Mild
User
PSM
Contrast
Brightness
Colour
Sharpness
PICTURE
()OO}{OOOKOOMENU
100
PSM
Contrast
Brightness
Colour
Sharpness
Press the MENU
button and then use
DD / EE
button to
select the PICTURE
menu.
Press the
GG button
and then use
DD / EE
button to select the
desired picture option.
Press the GG button and then use
FF / GG button to make appropriate
adjustments.
You can adjust picture contrast,
brightness, colour, sharpness and
tint (NTSC input only) to the levels
you prefer.
Picture adjustment
Picture Format
15
EN
You can watch TV in various picture formats; 16:9, 14:9, 4:3, Zoom, Panorama, Auto.
Repeatedly press the ARC button to select your desired picture format.
1. Press the ARC button to select a desired picture format.
• Each press of ARC button changes the screen display as shown below.
• You can also select
16:9, 14:9, 4:3, Zoom, Panorama, Auto in the SCREEN menu.
3
3
Picture format
16 : 9
Auto
14 : 9
4 : 3
Panorama
Zoom
Sound adjustment
16
SOUND
()OO}{OOOKOOMENU
SSM
Balance
AVL
SOUND
()OO}{OOOKOOMENU
Flat
Speech
Movie
Music
User
Press the MENU button and then
use
DD / EE
button to select the
SOUND menu.
Press the GG button and then use
DD / EE
button to select SSM.
Press the
GG button and then use
DD
/
EE
button to select a sound setting on
the
SSM pull-down menu.
Repeatedly press the MENU button to return to normal TV viewing.
1
1
Sound Frequency Adjustment
a. Press the GG button in User.
b. Select a sound band by pressing the
FF / GG button.
c. Make appropriate sound level with
the
DD / EE button.
d. Press the OK button to store it for the
sound
User.
The display Stored will appear.
You can also recall a desired sound
(
Flat, Speech, Movie, Music or
User) with SSM button on the remote
control. The sound
Flat, Speech,
Movie and Music are programmed for
good sound reproduction at the factory
and cannot be changed.
SSM (Sound Status Memory)
SSM
Balance
AVL
()OO}{OOOKOOMENU
0.1 0.5 1.0 5.0 10kHz
Sound adjustment
17
EN
Press the MENU button
and then use
DD / EE
button
to select the SOUND
menu.
Press the
GG button and
then use
DD / EE
button to
select
AVL.
Press the GG button and
then use
DD / EE
button to
select
On or Off.
3
3
Repeatedly press the
MENU button to return to
normal TV viewing.
This feature maintains an
equal volume level; even if
you change channels.
AVL (Auto Volume Leveler)
SOUND
()OO}{OOOKOOMENU
SSM
Balance
AVL
Press the MENU button and
then use
DD / EE
button to
select the SOUND menu.
Press the
GG button and then
use
DD / EE
button to select the
desired sound item.
Press the
GG button and then
use
FF / GG button to make
appropriate adjustments.
2
2
Repeatedly press the
MENU button to return to
normal TV viewing.
Balance
SOUND
()OO}{OOOKOOMENU
0SSM
Balance
AVL
SOUND
()OO}{OOOKOOMENU
SSM
Balance
AVL
SOUND
()OO}{OOOKOOMENU
Off
On
SSM
Balance
AVL
Sound adjustment
18
Language selection for dual language broadcast
If a programme received in two languages (dual language),
you can switch to
DUAL I, DUAL II or DUAL I+II by press-
ing the I/II button repeatedly.
DUAL I sends the primary broadcast language to the loud-
speakers.
DUAL II sends the secondary broadcast language to the
loudspeakers.
DUAL I+II sends a separate language to each loudspeaker.
If your set is equipped with the receiver for NICAM reception, the high quality NICAM (Near Instantaneous
Companding Audio Multiplex) digital sound can be
received.
Sound output can be selected according to the type of
received broadcast as follows by pressing the I/II button
repeatedly.
When NICAM mono is received, you can select
NICAM
MONO
or FM MONO.
When NICAM stereo is received, you can select NICAM
STEREO
or FM MONO. If the stereo signal is weak, switch
to FM mono.
When NICAM dual is received, you can select
NICAM
DUAL I
, NICAM DUAL II or NICAM DUAL I+II or
MONO. When FM mono is selected the display MONO
appears on the screen.
Mono sound selection
In stereo reception if the
stereo signal is weak, you
can switch to mono by
pressing the I/II button twice.
In mono reception the depth
of sound is improved. To
switch back to stereo, press
the I/II button twice again.
In AV mode, you can select
output sound for the left
and right loudspeakers.
Repeatedly press the I/II
button to select the sound
output.
L+R :Audio signal from
audio L input is sent to left
loud-speaker and audio
signal from audio R input is
sent to right loudspeaker.
L+L : Audio signal from
audio L input is sent to left
and right loudspeakers.
R+R : Audio signal from
audio R input is sent to left
and right loud-speakers.
4
4
Stereo/Dual/NICAM reception
STATION
Setting up TV stations
Auto programme tuning
19
EN
- Up to 100 TV stations can be stored by programme numbers (0 to 99). Once you have preset the stations, you will be
able to use the
DD / EE
or NUMBER buttons to scan the stations you programmed.
Stations can be tuned using automatic or manual modes.
- All stations that can be received are stored by this method. It is recommended that you use auto programme during
installation of this set.
Press the MENU
button and then use
DD / EE
button to
select the STATION
menu.
1
1
Press the GG button and then use
DD / EE
button
to select
Auto.
Press the GG button to display the Auto menu.
Press the GG button. Select a TV system with the
FF / GG button on the System pull-down menu;
L : SECAM L/L’ (France)
BG : PAL B/G, SECAM B/G (Europe/East
Europe)
I : PAL I/II (U.K./Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
Press the
DD / EE
button to select Storage.
Select the beginning programme number with
the
FF / GG button on the Storage pull-down
menu.
2
2
Press the
DD / EE
button to select Start.
Press the GG button to begin auto program-
ming.
All receivable stations are stored.
The station name is stored for stations which
broadcast VPS (Video Programme Service),
PDC (Programme Delivery Control) or TELETEXT data. If no station name can be
assigned to a station, the channel number is
assigned and stored as C (V/UHF 01-69) or S
(Cable 01-47), followed by a number.
To stop auto programming, press the MENU
button.
When auto programming is completed, the
edit menu appears on the screen. See the
‘Programme edit’section to edit the stored programme.
Repeatedly press the MENU button to return
to normal TV viewing.
3
3
STATION
()OO}{OOOKOOMENU
Auto
Manual
Edit
STATION
STOP : MENU
()OO}{OOOKOOMENU
Auto
Manual
Edit
System
FF
DK
GG
Storage From 7
Start
GGGGGG
Auto
Manual
Edit
System
FF
DK
GG
Storage From 7
Start
GGGGGG
7 14%
Setting up TV stations
Manual programme tuning
20
- Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can assign
a station name with five characters to each programme number.
Press the MENU
button and then use
DD / EE
button to
select the STATION
menu.
Press the GG button and then use
DD / EE
button
to select
Manual.
Press the GG button to display the Manual
menu.
Press the
DD / EE
button to select Storage.
Press the
FF / GG button to select the pro-
gramme number.
1
1
2
2
Press the
DD / EE
button to select System.
Select a TV system with the FF / GG button on the
System pull-down menu;
L : SECAM L/L’ (France)
BG : PAL B/G, SECAM B/G (Europe/East
Europe)
I : PAL I/II (U.K./Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
Press the
DD / EE
button to select Channel.
Press the
FF / GG button to select V/UHF or
Cable on the Channel pull-down menu.
3
3
STATION
()OO}{OOOKOOMENU
Auto
Manual
Edit
STATION
()OO}{OOOKOOMENU
Auto
Manual
Edit
Storage 4
System
FF
DK
GG
Channel V/UHF 33
Fine
GGGGGG
Search
GGGGGG
Name C 33
STATION
()OO}{OOOKOOMENU
Auto
Manual
Edit
Storage 4
System
FF
DK
GG
Channel V/UHF 33
Fine
GGGGGG
Search
GGGGGG
Name C 33
Setting up TV stations
Manual programme tuning
21
EN
Press the
DD / EE
button to select Fine.
Press the
FF / GG button to fine tune for the best picture and
sound.
Normally fine tuning is only necessary if reception is poor.
Press the
DD / EE
button to select Search.
Press the
FF / GG button to commence searching on the
Search pull-down menu. If a station is found the search
will stop.
If this station is the one required, press the OK button to
store it.
4
4
Press the
DD / EE
button to select Name.
Press the
GG button on the Name pull-down menu.
Press the
DD
button. You can use a blank, +, -, the
numeric
0 to 9 and the alphabet A to Z.
With the
EE
button you can select in the opposite direc-
tion.
Select the position by pressing the
FF / GG button and
then take your choice of the second character, and so
on.
Press the OK button.
Repeatedly press the MENU button to return to normal
TV viewing.
5
5
STATION
()OO}{OOOKOOMENU
Auto
Manual
Edit
Storage 4
System
FF
DK
GG
Channel V/UHF 33
Fine
GGGGGG
Search
GGGGGG
Name C 33
STATION
()OO}{OOOKOOMENU
Auto
Manual
Edit
Storage 4
System
FF
DK
GG
Channel V/UHF 33
Fine
GGGGGG
Search
GGGGGG
Name C 33
Setting up TV stations
Programme edit
22
- This function enables you to delete or skip the stored programmes. Also you can move some stations to other programme numbers or insert a blank station data into the selected programme number.
Press the MENU
button and then use
DD / EE
button to
select the STATION
menu.
1
1
Press the GG button and then
use
DD / EE
button to select
edit.
Press the
GG button to display
the edit menu.
Select a programme to be
deleted with the
DD / EE
or FF / GG
button.
Press the RED button twice.
The selected programme is
deleted, all the following programmes are shifted up one
position.
2
2
3
3
Deleting a programme
Select a programme to be
copied with the
DD / EE
or FF / GG
button.
Press the GREEN button.
All the following programmes
are shifted down one position.
4
4
Copying a programme
STATION
()OO}{OOOKOOMENU
Auto
Manual
Edit
GGGGGG
()OO}{OOOKOOMENU
0 C 04 5 - - - - 1 S 03 6 - - - - 2 S 04 7 - - - - 3 C 06 8 - - - - 4 C 33 9 - - - - -
Delete Copy
Move Skip
STATION
()OO}{OOOKOOMENU
Auto
Manual
Edit
Setting up TV stations
Programme edit
23
EN
Select a programme to be
moved with the
DD / EE
or FF / GG
button.
Press the YELLOW button.
Move the programme to the
desired programme number
with the
DD / EE
or FF / GG but-
ton.
Press the YELLOW button
again to release this function.
5
5
Moving a programme
Select a programme number to be skipped with the
DD / EE
or FF / GG button.
Press the BLUE button. The skipped programme turns
to blue.
Press the BLUE button again to release the skipped
programme.
When a programme number is skipped it means that
you will be unable to select it using the
DD / EE
button
during normal TV viewing. If you want to select the
skipped programme, directly enter the programme
number with the NUMBER buttons or select it in the
programme edit or table menu.
6
6
Skipping a programme number
7
7
Repeatedly press the MENU
button to return to normal TV
viewing.
Setting up TV stations
Calling the programme table
24
Press the LIST button to display the
Programme table menu.
The programme table appears on the
screen. One programme table contains ten programmes as below.
You may find some blue programmes. They have been set up to
be skipped by auto programming or
in the programme edit mode.
Some programmes with the channel
number shown in the programme
table indicate there is no station
name assigned.
1
1
Displaying programme table
Select a programme with the
DD / EE
or FF / GG button.
Then press the OK button.
The set switches to the chosen programme number.
2
2
Selecting a programme in the programme table
There are 10 programme table pages
which contain 100 programmes.
Pressing the
DD / EE
or FF / GG button
repeatedly turns the pages.
Repeatedly press the MENU button
to return to normal TV viewing.
3
3
Paging through a programme table
- You can check the programmes stored in the memory by displaying the programme table.
()OO}{OOOKOOMENU
0 - - - - - 5 - - - - 1 S 03 6 - - - - 2 C 33 7 - - - - 3 C 18 8 - - - - 4 9 - - - - -
Time Menu
25
EN
Clock
You must set the time correctly before
using on/off time function.
Press the MENU button and then
DD / EE
button to select the TIME menu.
Press the
GG
button and then
DD / EE
but-
ton to select
Clock.
Press the
GG
button and then
DD / EE
but-
ton to adjust the hour.
Press the
GG
button and then
DD / EE
but-
ton to adjust the minute.
Press the MENU or OK button to save.
The off timer automatically switches the set to standby at the preset time.
Press the MENU button and then
DD / EE
button to select the TIME menu.
Press the
GG
button and then
DD / EE
button to select Off Time or On Time.
Press the
GG
button and then
DD / EE
button to select On.
To cancel
Off/On Time function, press the
DD / EE
button to select Off.
Press the
GG
button and then
DD / EE
button to adjust the hour.
Press the
GG
button and then
DD / EE
button to adjust the minute.
Only On time function; Press the
GG
button and then
DD / EE
button to adjust
volume level and programe number.
Press the MENU or OK to save.
Note :
a.In the event of power interruption (disconnection or power failure), the clock
must be reset.
b.Two hours after the set is switched on by the on time function it will auto-
matically switch back to standby mode unless a button has been pressed.
c.Once the on or off time is set, these functions operate daily at the preset
time.
d.Off Timer function overrides On Timer function if they are set to the same
time.
e.The set must be in standby mode for the On Timer to work.
1
1
On/Off Time
2
2
TIME
()OO}{OOOKOOMENU
Clock
Off Time
On Time
Auto Sleep
TIME
()OO}{OOOKOOMENU
--:-- AM
TIME
()OO}{OOOKOOMENU
06:59 AM
PR. 7
VOL. 46
On
Clock
Off Time
On Time
Auto Sleep
Clock
Off Time
On Time
Auto Sleep
To initialize values (reset to
default settings), select the
Normal option.
Press the MENU button and
then
DD / EE
button to select
the SPECIAL menu.
Press the
GG button and then
DD / EE
button to select CSM.
Press the
GG button and then
DD / EE
button to select the
desired colour temperature.
Press the MENU button to
save.
CSM (Colour Status
Memory)
Time Menu /
Other functions
26
Auto sleep
If you select On on the Auto
Sleep
menu, the set will automatically switch itself to standby
mode approximately ten minutes
after a TV station stops broadcasting.
Press the MENU button and then
DD / EE
button to select the TIME
menu.
Press the
GG button and then
DD /
EE
button to select Auto Sleep.
Press the GG button and then
DD /
EE
button to select On or Off.
Press the MENU
or OK
button to
save.
You don’t have to remember to switch the set
off before you go to sleep. The sleep timer
automatically switches the set to standby
after the preset time has elapsed.
Press the SLEEP button to select the number
of minutes. The display ‘ ’ will appear
on the screen, followed by
10, 20, 30, 60, 90,
120, 180
and 240. The timer begins to count
down from the number of minutes selected.
Note :
a.To view the remaining sleep time, press the
SLEEP button once.
b.To cancel the sleep time, repeatedly press
the SLEEP button until the display Ô ’Õ
appears.
c.When you switch the set off, the set releas-
es the preset sleep time.
3
3
Sleep timer
4
4
TIME
()OO}{OOOKOOMENU
On
Off
Clock
Off Time
On Time
Auto Sleep
SPECIAL
()OO}{OOOKOOMENU
Cool
Normal
Warm
Language
CSM
PC Control
WXGA
Set ID
rr - - -
rr - - -
SPECIAL
()OO}{OOOKOOMENU
Language
CSM
PC Control
WXGA
Set ID
27
EN
Connection of PC
You can adjust horizontal/vertical position, clock, phase, and auto-configure, reset as you prefer.
Press the MENU button and then
DD / EE
button to select the Special menu.
Press the
GG button and then
DD / EE
button to select the desired picture item.
Press the
FF / GG button to make appropriate adjustments.
H-Position / V-Position
This function is to adjust picture to left/right and up/down as you prefer.
Clock
This function is to minimize any vertical bars or stripes visible on the screen background. And the horizontal screen size
will also change.
Phase
This function allows you to remove any horizontal noise and clear or sharpen the image of characters.
Auto-configure
This function is for the automatic adjustment of the screen position, clock and phase. The displayed image will disappear
for a few seconds while the Auto-configuration is in progress.
Reset
This function allows you to return to the good picture reproduction programmed at the factory and cannot be changed.
Note : Some signal from some graphics boards may not function properly. If the results are unsatisfactory, adjust your
monitorÕs position, clock and phase manually.
Press the OK button to store it for the PC monitor picture.
Press the EXIT button to return to PC mode.
PC Setup
To see a normal picture, match the resolution of RGB mode and selection of XGA mode.
WXGA
SPECIAL
()OO}{OOOKOOMENU
H-Pos. 0
V-Pos. 0
Clock 10
Phase 15
Auto
Reset
Language
CSM
PC Control
WXGA
Set ID
28
PIP (Picture-In-Picture) Feature
Press the PIP button to show the sub picture.
• Each press of PIP button changes the screen display as shown below.
1
1
Watching PIP
Press the PIP POSITION button.
Press the PIP POSITION button
repeatedly until desired position is
achieved. The sub pictures move
clockwise.
2
2
Moving the PIP
- PIP lets you view 2 different inputs (sources) on your monitor screen at the same time. One source will be large, and
the other source will show a smaller inset image.
29
EN
PIP (Picture-In-Picture) Feature
Press the SWAP button to exchange
the main and sub pictures.
3
3
Swapping the PIP
Use the PIP INPUT button to
select the input source for the sub
picture.
4
4
Selecting a Input Signal
Source for the PIP
This function enables you to search all
the stored stations on 4 or 12 sub pictures and see your favourite station by
exchanging the main and sub pictures.
Press the SCAN button repeatedly to
select POP4/POP12.
The selected sub or main pictures
search all the stored stations.
Press the EXIT button to switch off
sub or main pictures.
6
6
Programme scan
Press the PIP PR +/- button. The
selected programme number is
displayed just below the programme number of main picture.
5
5
Programme selection for
sub picture
Main Picture Sub Picture
30
Teletext (or TOP text) is an optional function, therefore only
a set with the teletext system can receive the teletext
broadcast.
Teletext is a free service broadcast by most TV stations
which gives up-to-the-minute information on news, weather, television programmes, share prices and many other
topics.
The teletext decoder of this TV can support the SIMPLE,
TOP and FASTEXT systems. SIMPLE (standard teletext)
consists of a number of pages which are selected by
directly entering the corresponding page number. TOPand
FASTEXT are more modern methods allowing quick and
easy selection of teletext information.
Switch on/off
Press the TEXT button to switch to teletext.
The initial page or last page appears on the screen.
Two page numbers, TV station name, date and time are
displayed on the screen headline. The first page number
indicates your selection, while the second shows the current page displayed.
Press the TEXT button to switch off teletext. The previous
mode reappears.
SIMPLE text
Page selection
1. Enter the desired page number as a three digit number
with the NUMBER buttons. If during selection you
press a wrong number, you must complete the three
digit number and then re-enter the correct page number.
2. The
DD / EE
button can be used to select the preced-
ing or following page.
Programming a colour button in LIST mode
If the TV is in SIMPLE text, TOP text or FASTEXT mode,
press the button to switch to LIST mode.
Four teletext page numbers of your choice can be colour
coded and easily selected by pressing the corresponding
coloured button on the remote control handset.
1. Press a coloured button.
2. Using the NUMBER buttons, select the page you wish
to programme.
3. Press the OK button. The selected page is stored as
the selected page number, blinking once to confirm
this. From now on, you can select this page with the
same coloured button.
4. The three other coloured buttons are programmed in
this way.
TOP text (option)
The user guide displays four fields-red, green, yellow and
blue at the bottom of the screen. The yellow field denotes
the next group and the blue field indicates the next block.
Block / group / page selection
1. With the blue button you can progress from block to
block.
2. Use the yellow button to proceed to the next group with
automatic overflow to the next block.
3. With the green button you can proceed to the next
existing page with automatic overflow to the next
group.
Alternatively the
DD
button can be used.
4. The red button permits to return to previous selection.
Alternatively the
EE
button can be used.
Direct page selection
Corresponding to the SIMPLE teletext mode, you can
select a page by entering it as a three digit number using
the NUMBER buttons in TOP mode.
Teletext (option)
Loading...