JVC SP-THF3W, SP-THF3F, XV-THF3, LVT1833-001B User Manual
DVD DIGITAL THEATER SYSTEM
TH-F3
Consists of XV-THF3, SP-THF3F and SP-THF3W
English
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT1833-001B
[J, C]
Warnings, cautions and others
(For U.S.A.)
(For U.S.A.)
(For U.S.A.)
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.
(For U.S.A.)
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
G-1
For Canada/pour le Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS
FROM DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING EQUIPMENT STANDARD
ENTITLED “DIGITAL APPARATUS”, ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS NUMIRIQUES DE CLASSE B PRESCRITES DANS LA NORME SUR LE MATERIEL BROUILLEUR: “APPAREILS NUMERIQUES”, NMB-003 EDICTEE PAR LE MINISTRE DES
COMMUNICATIONS.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
CAUTION — F button!
Disconnect the mains plug to shut the power off completely (the STANDBY lamp goes off). When installing the apparatus, ensure that the plug is easily accessible.
The F button in any position does not disconnect the mains line.
• When the system is on standby, the STANDBY lamp lights red.
• When the system is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
ATTENTION — Touche F!
Déconnectez la fiche secteur pour mettre l’appareil complètement hors tension (le témoin STANDBY
s’éteint). Lors de l’installation de l’appareil, assurez-vous que la fiche soit facilement accessible.
La touche F, dans n’importe quelle position, ne déconnecte pas le système du secteur.
• Quand le système est en attente, le témoin STANDBY est allumé en rouge.
• Quand le système est sous tension, le témoin STANDBY s’éteint.
L’alimentation peut être télécommandée.
CAUTION
• Excessive sound pressure from earphones or headphones can cause hearing loss.
ATTENTION:
• Une pression acoustique excessive des écouteurs ou du casque d’écoute peut entraîner une perte auditive.
G-2
Warnings, cautions and others (continued)
IMPORTANT FOR LASER PRODUCTS /
IMPORTANT POUR PRODUITS LASER
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet. There are no user serviceable parts inside the unit;
leave all servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with
optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.
1. PRODUIT LASER CLASSE 1
2. ATTENTION: N’ouvrez pas le couvercle supérieur ni le coffret de l’appareil. Il n’y a aucune pièce répa-
rable par l’utilisateur à l’intérieur de l’appareil; confiez toute réparation à un personnel qualifié.
3. ATTENTION: Rayonnement laser visible et/ou invisible de classe 1M une fois ouvert. Ne pas regarder
directement dans le faisceau avec des instruments optiques.
4. REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE DE PRÉCAUTION PLACÉE À L’INTERIEUR DE
L’APPAREIL.
CAUTION
• Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able
to get out.)
• Do not place any naked flame sources, such as lighted candles, on the apparatus.
• When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
ATTENTION
• Ne bloquez pas les orifices ou les trous de ventilation.
(Si les orifices ou les trous de ventilation sont bloqués par un journal un tissu, etc., la chaleur peut ne
pas être évacuée correctement de l’appareil.)
• Ne placez aucune source de flamme nue, telle qu’une bougie, sur l’appareil.
• Lors de la mise au rebut des piles, veuillez prendre en considération les problèmes de l’environnement
et suivre strictement les règles et les lois locales sur la mise au rebut des piles.
• N’exposez pas cet appareil à la pluie, à l’humidité, à un égouttement ou à des éclaboussures et ne
placez pas des objets remplis de liquide, tels qu’un vase, sur l’appareil.
G-3
CAUTION — Proper Ventilation
To avoid risk of electric shock and fire and to protect from damage, locate the apparatus as follows:
Top/Front/Back/Sides: No obstructions should be placed in the areas shown by the dimensions below.
Bottom: Place on the level surface. Maintain adequate air path for ventilation by placing on
a stand with a height of 10 cm more.
In addition, maintain the best possible air circulation.
Attention: Ventilation correcte
Pour éviter tout risque d’électrocution et d’incendie, et pour ne pas endommager les appareils, placez-les
de la façon suivante:
Faces supérieure /avant / arrière / côtés : Aucune obstruction ne doit se trouver dans les zones
indiquées par les dimensions ci-dessous.
Bas : Placez l’appareil sur une surface plane. Maintenez une entrée
d’air adéquate pour la ventilation en plaçant l’appareil sur un
support avec une hauteur d’au moins 10 cm.
De plus, maintenez la meilleure circulation d’air possible.
Front view of the main unit and speakers (XV-THF3 and SP-THF3F)
Vue avant de l’unité principale et des haut-parleurs (XV-THF3 et SP-THF3F)
15cm
15
(5 ″)
16
5cm
(2″)
15cm
(5 ″)
5cm
(2″)
15
16
15cm
15
(5 ″)
16
10cm
15
(3 ″)
16
Side view of the main unit (XV-THF3)
Vue latérale de l’unité principale (XV-THF3)
15cm
15
Front
(5 ″)
16
Avant
Wall or obstructions
Mur, ou obstruction
CAUTION
• Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
PRECAUTION
• Les piles ne doivent en aucun cas être exposées à une chaleur excessive (lumière du solei, feu, etc.).
[European Union only]
[Union européenne seulement]
G-4
Table of contents
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain
the best possible performance from the unit.
Introduction
Introduction
Part description .............................3
Using the remote control ..............4
Inserting the batteries into the remote
control...........................................................4
Operating the system from the remote
control...........................................................4
Preparation
Preparation.....................................5
Connecting the antennas ................................ 5
Connecting the speakers and subwoofer........ 6
Connecting the docking station for iPod .........7
Connecting a TV .............................................8
Connecting external digital audio devices....... 9
Connecting external analog audio devices .....9
Connecting the power cable ...........................9
Selecting the video signal type .....................10
Basic operations
Basic operations..........................11
Using the number buttons.............................11
Turning on/off the main unit ..........................11
Adjusting the volume.....................................12
Turning off the sound temporarily .................12
Adjusting the treble/bass...............................12
Adjusting the volume level for surround/
subwoofer sound ........................................12
Selecting the surround mode........................12
Selecting the headphone surround mode .....13
Sharpening the voice sound .........................13
Selecting the surround volume level.............13
Using the sleep timer ....................................14
Changing the brightness of the display
window........................................................14
Locking disc ejection.....................................14
Playing back sources from
external devices
Playing back sources from
external devices...........................17
Playing back sources from external
devices........................................................17
Selecting the signal gain ...............................17
Basic operations of disc/file
playback
Basic operations of disc/file
playback .......................................18
Playing back a disc .......................................18
Playing back a file .........................................19
Display window on the main unit for disc/file
types ...........................................................20
Stopping playback.........................................25
Resuming playback.......................................25
Pausing playback..........................................25
Advancing the picture frame by frame ..........25
Fast reverse/fast forward search ..................26
Playing back from a position 10 seconds
before..........................................................26
Slow motion playback ...................................26
Skipping to the beginning of a
chapter/track/file .........................................27
Selecting a chapter/track using the number
buttons........................................................27
Skipping at approximately 5 minute
intervals ......................................................27
Selecting a chapter/track from the
menu screen...............................................28
Listening to radio broadcasts
Listening to radio broadcasts ....15
Selecting a radio station................................15
Tuning in to a preset radio station.................16
1
Convenient functions of
disc/file playback
Basic operations of HDMI
CEC
Convenient functions of disc/file
playback .......................................29
Playing back a disc/file in the desired order
(Program playback) ....................................29
Playing back a disc/file in a random order
(Random playback) ....................................31
Playing back a disc/file repeatedly
(Repeat playback) ......................................31
Selecting the audio language and subtitle
language.....................................................32
Magnifying the picture...................................32
Adjusting the picture quality (VFP)................33
Playing back the bonus group.......................34
Using the status bar and
the menu bar ................................35
Playing back a specified part repeatedly
(A-B repeat playback).................................37
Designating the time (Time search) .............. 37
Changing the initial settings with
the preference screen .................38
Basic operations ...........................................38
LANGUAGE.................................................. 38
PICTURE ......................................................39
AUDIO...........................................................40
OTHERS.......................................................40
Language codes ..........................42
Basic operations of HDMI CEC...50
Introduction
Reference
Notes on operation ......................51
Suitable locations for the main unit ...............51
Condensation................................................51
Cleaning the main unit ..................................51
Notes on handling .........................................51
License and trademark .................................52
Notes on discs/files .....................53
Playable disc/file types..................................53
Data hierarchy...............................................56
Handling discs............................................... 56
Troubleshooting...........................57
Specifications ..............................61
Main unit (XV-THF3) .....................................61
Speaker (SP-THF3F) ....................................61
Subwoofer (SP-THF3W) ...............................61
Supplied accessories ....................................61
Playing back sound from an
iPod
Playing back sound from
an iPod..........................................43
Playing back sound from an iPod .................43
Operating the iPod using the
remote control.............................................44
Changing the time when the backlight
turns on.......................................................45
Charging the battery of the connected
iPod ............................................................45
Notes on an iPod ..........................................45
Operating external devices
using the remote control
Operating external devices using
the remote control .......................46
Operating a TV using the remote control ...... 46
Operating a DBS using the remote control ...47
Operating a VCR using the remote control ... 48
How to read this manual
• This manual explains the operations assuming that you will use the remote control.
Some buttons on the main unit are the same
as those on the remote control. You can use
either button in this case.
• Some diagrams in this manual are simplified
or exaggerated for the purpose of explanation.
• You can operate some functions differently
from the explanation given in this manual.
• Depending on the disc/file, you may not
obtain the explained result even after following the operation in this manual.
• The following marks refer to the usable
discs/files for the explained function.
2
Part description
The numbers refer to the pages in which the parts are explained.
Front view
Introduction
Refer to “Display window” shown below.
Remote control sensor
Rear view
Display window
3
Cooling fan
Using the remote control
The numbers refer to the pages in which the parts
are explained.
Inserting the batteries into the remote control
Insert the batteries into the remote control by
matching the polarity (+ and −) correctly.
R03 (UM-4)/AAA
(24F) type dry-cell
batteries (supplied)
• If the range or effectiveness of the remote control decreases, replace both batteries.
Operating the system from the remote control
Point the remote control directly at the
front of the main unit.
• Do not block the remote control sensor on the
main unit.
Introduction
4
Preparation
Do not connect the power cable until all other connections have been made.
Connecting the antennas
FM antenna (supplied)
AM loop antenna (supplied)
Preparation
Setting up the AM loop antenna
If insulation covers the tips of the
antenna cable, twist and pull off
the insulation.
NOTE
• Keep the AM loop antenna cable wrapped
around the AM loop antenna frame, otherwise
the effectiveness and sensitivity of the AM loop
antenna may be reduced.
Connecting the AM loop antenna
Main unit (rear view)
Main unit (rear view)
When radio reception with the supplied FM
antenna is poor, or when using a communal
antenna
Main unit (rear view)
Antenna cable
(not supplied)
or
Converter (not supplied: compatible
with 300
Depending on the radio reception
conditions, an FM feeder
antenna (not supplied: compatible with 300 C) can be used. In
this case, a converter (not supplied) is required.
C
FM antenna
Stretch out the FM
antenna to the best
position for radio
reception.
Communal
antenna terminal
Outdoor FM
antenna
(not supplied)
Coaxial cable
/75 C)
(not supplied)
Turn the AM loop antenna to find the best position
for radio reception.
NOTE
• Make sure that the antenna conductors do not
touch any other terminals. This could cause poor
reception.
• When using an antenna other than those supplied with this system, refer to the operation
manuals for the antenna and converter for
details of connection.
• When positioning the antennas, find the best
position for reception while listening to an actual
radio program (refer to “Listening to radio broadcasts” on page 15).
• You cannot receive an FM/AM radio broadcast
without the antenna connection.
5
Connecting the speakers and subwoofer
Connect the speakers to the main unit by connecting the colored connectors to the same color terminals on
the rear of the main unit.
Red
Main unit (rear view)
White
Speaker cableSpeaker cable
Preparation
Right speaker
(rear view)
■ IMPORTANT
• Improper speaker cable connection reduces the
stereo effect and sound quality.
• The supplied left/right speakers are magnetically
shielded, but color irregularity may occur on the
TV depending on some conditions. To prevent
color irregularity, set up the speakers following
the instructions below.
(The subwoofer is not magnetically shielded.)
1. Turn off the main power of the TV before
setting up the speakers.
2. Place the speakers enough distance from the
TV so that they do not cause color irregularity
on the TV.
3. Wait for approximately 30 minutes before
turning on the main power of the TV again.
Gray
Subwoofer
(rear view)
Speaker cable
Blue
Purple
CAUTION
• The supplied speakers are manufactured exclusively for use with the supplied main unit as
parts of this system. Do not connect the supplied
speakers to devices other than the supplied
main unit. Doing so may damage the speakers.
• Do not connect external speakers together with
the supplied speakers. The change in impedance may damage the main unit and the speakers.
Left speaker
(rear view)
6
Preparation (continued) Do not connect the power cable until all other connections have been made.
Using the speakers with commercially
available speaker stands
The left and right speakers can be fitted onto commercially available speaker stands. Before fitting
Preparation
the speakers onto commercially available speaker
stands, remove the speaker cables from the tabs
and slots on the speakers.
Remove the cable from
the shorter tab first.
Longer tabBottom view
Speaker layout
This system is designed to provide virtual surround
sound by positioning the 3 speakers in front. (The
set of the left and right speakers and the subwoofer refers to 2.1 channel.) The front surround
function processes input signals to create a realistic sound field.
Main unit
Subwoofer
Left speaker
Right speaker
Connecting the docking station for iPod
CAUTION
• The left and right speakers can be installed on a
wall.
• When installing the speakers on a wall, be sure
to have the speakers installed by qualified personnel.
• DO NOT install the speakers on the wall by yourself to avoid unexpected damage from them falling off the wall due to incorrect installation or
weakness in wall structure.
• Care must be taken in selecting a location for
speaker installation on a wall. Injury to personnel
or damage to devices may result if the installed
speakers interfere with daily activities.
Connect the plug with
the arrow facing up.
Main unit
(rear view)
Docking station for iPod (supplied)
CAUTION
• Do not touch the pins of the [iPod] terminal on
the rear of the main unit or the pins of the docking station for iPod.
• Do not carry the main unit with the docking station for iPod connected. You may drop them and
damage the connector part.
7
Connecting a TV
After connecting a TV, follow the instructions on
page 10.
■ IMPORTANT
• Connect the main unit directly to a TV (or a monitor) without routing through a video cassette
recorder (VCR). Otherwise picture distortion
may occur during playback. (Routing the connection through a VCR, however, does not affect
the audio quality.)
Main unit
TV (or monitor)VCR
Connecting a TV with the
[COMPONENT] terminals
TV
Preparation
Main unit
(rear view)
To component
input terminals
Direct connection
• Connecting the main unit to a VCR-built-in-TV
may also cause picture distortion during playback.
Connecting a TV with the [VIDEO]
terminal
TV
Main unit
(rear view)
To a video input terminal
Composite video cable (supplied)
Component video cable (not supplied)
Connecting a TV with the [HDMI
MONITOR OUT] terminal
This system can output uncompressed digital
video signals to a TV compatible with HDMI (High
Definition Multimedia Interface).
Main unit
(rear view)
To an HDMI input terminal
HDMI cable (not supplied)
NOTE
• The HDMI video signal type can be checked with
the “HDMI” indicator in the display window.
(Refer to “Selecting the video signal type” on
page 10.)
• If the picture is distorted while an HDMI TV is
connected, turn off the main unit and turn it on
again.
• A TV compatible with HDCP (High-Bandwidth
Digital Content Protection) can also be connected to the [HDMI MONITOR OUT] terminal,
so that the uncompressed HD video signal type
can be output as well.
• This system is compatible with some basic functions of HDMI CEC. (Refer to page 50.)
8
Preparation (continued) Do not connect the power cable until all other connections have been made.
Connecting external digital audio devices
Preparation
Output MD player or
satellite receiver
To an optical digital
output terminal
Optical digital cable
(not supplied)
Main unit
(rear view)
Input Output
Connecting external analog audio devices
Output
Input
Main unit
(rear view)
Analog audio
device
Audio cable
(not supplied)
Optical digital cable
(not supplied)
To an optical digital
input terminal
Input
NOTE
• You can output the audio signal from the
[DIGITAL OUT] terminal when “DVD”, “USB” or
“DGTL IN” is selected as the source in the display window.
• When “DGTL IN” is selected as the source in the
display window, digital audio from the
[DIGITAL OUT] terminal is decoded to a linear
PCM signal.
AV amplifier with
a built-in decoder
Connecting the power cable
AC outlet
Main unit
(rear view)
• Connect the power cable after you complete the
other connections.
F
• The [STANDBY
up.
] lamp on the main unit lights
9
Selecting the video signal type
To view an image on the TV screen, select the
video signal type correctly according to the TV
after connecting the main unit to the TV.
Remote control
mode selector
2/3 (cursor)/
ENTER
■ IMPORTANT
• Slide the remote control mode
selector to [SHIFT].
4 Press 2 or 3 (cursor) to select the
video signal type suitable for the
TV.
• When the TV is connected to the [VIDEO]
terminal, select “480I”.
• When the TV is connected to the [COMPONENT] terminals, select “480P”. (If the TV is
not compatible with a progressive video signal, select “480I”.)
• When the TV is connected to the [HDMI
MONITOR OUT] terminal, the video signal
type can be selected as instructed below.
- Select “AUTO” for normal usage. (the ini-
tial setting)
- Select “480P”, “720P”, “1080I” or “1080P”
as needed. (The selectable settings differ
according to the resolution of the connected TV.)
• You can also select the video signal type by
repeatedly pressing [SCAN MODE].
NOTE
• “480”, “720” and “1080” refer to the number of
the scanning lines. Generally, the larger the
number, the better picture that can be obtained.
• “I” refers to the interlaced format. “P” refers to
the progressive format. A better picture can be
obtained in the progressive format than in the
interlaced format.
• When an HDMI video signal is output, the
“HDMI” indicator lights up in the display window.
• When an HD video signal is output, the “HD”
indicator lights up.
• When “480P”, “720P” or “1080P” is selected, the
“PROGRESSIVE” indicator lights up in the display window.
5 Press [ENTER].
Preparation
1 Turn on the main unit.
• Refer to “Turning on/off the main unit” on
page 11.
2 Press [DVD 3] or [USB 3].
• When a disc is loaded or a USB device is
connected, press 7 to stop playback.
3 Press [SCAN MODE].
• The current video signal type appears.
Example: When “480I” is selected as the
video signal
NOTE
• It is recommended that you slide the remote
control mode selector to [AUDIO] after selecting
the video signal type. Most of the other functions
can be used when the remote control mode
selector is at [AUDIO].
• To check the compatibility of your TV, contact
your local JVC customer service center.
• Even if the main unit is turned off, the video signal type setting is stored.
10
Basic operations
Number
Basic operations
buttons
*
Using the number buttons
Examples:
5: [5]
15: [ 10] →
150: [ 10] → [ 10] → [1] → [5] → [0]
[1] → [5]
■ IMPORTANT
• Slide the remote control mode
selector to [AUDIO].
Remote control
mode selector
Turning on/off the main unit
F
Press [AUDIO
] (or [STANDBY F]
on the main unit).
• The power of the main unit turns on and the
[STANDBY
turns off.
• Press [AUDIO
main unit) again to turn off the power of the main
unit. (The main unit enters the standby mode.)
• With the power off, pressing any of the following
buttons also turns on the main unit.
- [DVD 3], [USB 3], [iPod 3], [FM/AM],
[AUDIO IN/DIGITAL IN], 3 (playback) or 0 on
the remote control
- s3 (playback) or 0 on the main unit
The function assigned to the pressed button
starts working at the same time. (When 3 (playback) is pressed, “DVD” is selected as the
source in the display window.)
• An internal cooling fan turns on when the main
unit turns on. This is to prevent overheating of
the main unit. The cooling fan produces noise
during operation. This is not a malfunction.
F
] lamp (button) on the main unit
F
] (or [STANDBYF] on the
11
Adjusting the volume
Press [VOL +] or [VOL –] repeatedly.
• You can also adjust the volume by turning the
[VOLUME] control on the main unit.
Turning off the sound temporarily
Press [MUTING].
• Press [MUTING] again or [VOL +] or [VOL –], or
turn the [VOLUME] control on the main unit to
restore the sound. The sound is also restored
when the main unit is turned off once and turned
on.
Adjusting the treble/bass
1 Press [TREBLE/BASS] repeatedly
to select “TRE” or “BASS” in the
display window.
Adjusting the volume level for surround/subwoofer sound
You can adjust the volume level for the left and
right surround sound and the subwoofer sound
respectively.
1 Press [SPK LEVEL] repeatedly to
select “SURR” or “SUBWFR” in
the display window.
• “SURR” refers to the left and right surround
sound.
• “SUBWFR” refers to the subwoofer sound.
2 Press [LEVEL +] or [LEVEL
repeatedly to adjust the volume
level.
• The adjustable volume range is from -6 to +6.
Selecting the surround mode
–
]
Basic operations
2 Press [LEVEL +] or [LEVEL –]
repeatedly to adjust the sound
quality.
• Adjustable sound quality is from -10 to +10.
Press [SURROUND].
• Each time you press [SURROUND], the display
changes in the display window as follows.
-“AUTO SUR”
When a multi-channel signal is input, surround
sound is automatically produced.
- “MOVIE”
Surround sound suitable for a movie or multichannel signal is produced.
- “WIDE/2CH”
When a 2ch signal is input, surround sound is
produced. The sound is broader than the one
with “MOVIE”.
-“SUPER W”
Surround sound broader than the one with the
“WIDE/2CH” is produced.
NOTE
• Depending on the signal type, surround sound
may not be produced as the surround mode setting.
• During playback, when you change the surround
mode setting, sound from the [DIGITAL OUT]
terminal may be intermittent. Before recording
sound to an external device, select the desired
surround mode setting.
• This function does not work for a JPEG/ASF/
DivX/MPEG1/MPEG2 file.
12
Basic operations (continued)
Selecting the headphone surround mode
You can listen to surround sound via headphones
connected to the [PHONES] terminal.
■ When headphones are connected to the
Basic operations
[PHONES] terminal
Press [SURROUND].
• Each time you press [SURROUND], the setting
toggles between “H.P. SURR” and “H.PHONE”
in the display window.
NOTE
• The [PHONES] terminal is for connecting a pair
of headphones equipped with a stereo mini plug
(not supplied). When headphones are connected, no sound is output from the speakers.
• This function does not work for a JPEG/ASF/
DivX/MPEG1/MPEG2 file.
Sharpening the voice sound
This function allows you to easily understand dialog recorded on the disc/file even with the volume
down low. This function is useful when you are
watching a movie.
Selecting the surround volume level
You can increase the surround volume level.
This function is effective for the following conditions:
(1) When the surround mode is set to an item
other than “AUTO SUR” (Refer to page 12.)
(2) When the surround mode is set to “AUTO
SUR” and a DVD VIDEO, DVD AUDIO or DVD
VR is played back (Refer to page 18.)
(3) When the surround mode is set to “AUTO
SUR” and the source is set to “DGTL IN”
(Refer to page 17.)
1 Press [SETTING] repeatedly to
select “SURR VOL” in the display
window.
2 Press [LEVEL +] or [LEVEL –]
repeatedly to select the desired
setting in the display window.
• Each time you press [LEVEL +] or [LEVEL –],
the surround volume level display changes to
one of three levels. The surround volume
level increases in the order of “SURR:
NRML”, “SURR: MID” and “SURR: HIGH”.
• Select the surround volume level while listening to the actual sound to confirm the difference.
1 Press [SETTING] repeatedly to
select “CLR VOIC” in the display
window.
• “CLR VOIC” refers to a clear voice.
2 Press [LEVEL +] or [LEVEL –]
repeatedly to select “CLR: ON” in
the display window.
This indicator lights up when the
clear voice function is activated.
• Each time you press [LEVEL +] or [LEVEL –],
the clear voice function turns on and off.
• When you want to deactivate the clear voice
function, select “CLR: OFF”.
NOTE
• This function does not affect the sound with the
headphone surround mode.
13
For the locations of the remote
control buttons, refer to page 11.
Using the sleep timer
When the time you specify elapses, the main unit
automatically turns off.
Press [SLEEP].
• Each time you press [SLEEP], the time indicated in
the display window changes. You can set the time
to 10, 20, 30, 60, 90, 120, 150 or 180 minutes.
Example: Display when the sleep timer is
set to 60 minutes
Changing the remaining time
Press [SLEEP] repeatedly to select the
time again.
Confirming the remaining time
Press [SLEEP] once.
Canceling the sleep timer
Press [SLEEP] repeatedly until
“SLEEP --” appears.
Turning off the main unit cancels the sleep timer.
Changing the brightness of the display window
■ When the main unit is turned on
Press [DIMMER] repeatedly.
• Each time you press [DIMMER], the brightness
changes in 3 levels.
Locking disc ejection
You can lock the disc tray to prevent the disc from
being ejected.
Setting the disc ejection lock
■ When the main unit is turned off
Hold down 0 on the main unit for one
or more seconds while holding down
7 on the main unit.
Basic operations
If you attempt to open the disc tray by pressing 0,
the disc tray does not open and “LOCKED”
appears in the display window.
To cancel the disc ejection lock, press 0 on the
main unit while holding down 7 on the main unit
again. “UNLOCKED” is displayed in the display
window.
14
Listening to radio broadcasts
1 Press [FM/AM] to select “FM” or
Number
buttons
*
Remote control
mode selector
Listening to radio broadcasts
Selecting a radio station
“AM” in the display window.
• Pressing [FM/AM] selects a radio broadcast
as the sound source.
• Repeatedly pressing [SOURCE] on the
main unit can also select a radio broadcast
as the source.
• Each time you press [FM/AM], the band toggles between “FM” and “AM”.
Example: When an FM radio broadcast is
received
Stereo indicator
For the number button usage, refer to “Using the
*
number buttons” on page 11.
■ IMPORTANT
• Slide the remote control mode
selector to [AUDIO].
Preset number
(Refer to page 16.)
Frequency
2 Press [TUNING ] or [TUNING ]
repeatedly to select a radio station
(frequency).
• When the main unit has received an FM stereo broadcast, the “ST” (stereo) indicator
lights up in the display window.
■ Automatic tuning:
You can also select a radio station using automatic tuning.
Hold down [TUNING ] or [TUNING ] until
the frequency starts changing, and then
release the button.
• When the main unit has received a broadcast, the frequency automatically stops
changing.
• You can select a specific radio station while
searching for a broadcast. Press [TUNING ] or [TUNING ] to stop automatic
tuning when the desired frequency appears
in the display window.
NOTE
• If an FM stereo broadcast is difficult to hear
because of noise, you may be able to hear the
broadcast more easily by pressing [FM MODE]
to switch the sound to monaural reception. In
this case, the “MONO” (monaural) indicator
lights up in the display window. To return the
sound to stereo reception, press [FM MODE]
again. “AUTO” is displayed and the “ST” (stereo)
indicator lights up in the display window.
15
Tuning in to a preset radio station
Presetting radio stations in the main unit allows
you to easily tune in to a radio station.
Presetting radio stations
You can store up to 30 FM radio stations and up to
15 AM radio stations.
1 Select a radio station you want to
store.
• Refer to “Selecting a radio station” on page
15.
2 Press [ENTER].
•“--” flashes in the display window for
approximately 5 seconds.
3 While “
number buttons to select the preset number you want to assign.
• You can also select the preset number by
pressing [PRESET ] or [PRESET ].
--
” is flashing, press the
Listening to radio broadcasts
4 Press [ENTER] while the selected
number is flashing.
• “STORED” appears and the selected radio
station is stored.
NOTE
• When you store a radio station to a preset number to which another radio station has previously
been stored, the newly set radio station replaces
the previously stored radio station.
Tuning in to a preset radio station
■ When an FM or AM radio broadcast is
selected as the source
Press the number buttons to select
the preset number of the radio station
to which you want to tune in.
• You can also select the preset number by pressing [PRESET ] or [PRESET ].
16
Loading...