DVD PLAYER
XV-N652S
XV-N650B
INSTRUCTIONS
For Customer Use :
Enter below the Model No. and
Serial No. which are located on
the rear of cabinet. Retain this
information for future reference.
Model No.
Serial No.
LPT1147-001A
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol within
an equilateral triangle is intended to alert the user
to the presence of uninsulated dangerous voltage
within the productʼs enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE AND OBJECTS
FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD
NOT BE PLACED ON THIS APPARATUS.
WARNING: Do not install this equipment in a confined space
such as a bookcase or similar unit.
CAUTION: Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect
it from over heating.
The openings should be never be blocked by placing the
product on a bed, sofa, rug or other similar surface. This
product should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided or
the manufacturer's instruction have been adhered to.
CAUTION:
This product employs a Laser System.
To ensure proper use of this product, please read this
ownerʼs manual carefully and retain it for future reference.
Should the unit require maintenance, contact an authorized
service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser radiation when open. DO NOT
STARE INTO BEAM.
FCC WARNING: This equipment may generate or use
radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the
modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is
made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
CAUTION concerning the Power Cord
Most devices are recommended be placed on a
dedicated circuit;
That is, a single outlet circuit which powers only that
electronic device and has no additional outlets or branch
circuits. Check the specification page of this owner's manual
to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose
or damaged wall outlets, extension cords, frayed power
cords, or damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced
with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse,
such as being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall outlets,
and the point where the cord exits the appliance.
To disconnect power from the mains, pull out the mains cord
plug. When installing the product, ensure that the plug is
easily accessible.
2
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or
fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for
installation, use, and servicing.
This product does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions. - All these safety and
operating instructions should be read before the product
is operated.
2. Keep these instructions. - The safety, operating and
use instructions should be retained for future reference.
3. Heed all warnings. - All warnings on the product and in
the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use
instructions should be followed.
5. Do not use this apparatus near water. - For example:
near a bath tub, wash bowl, kitchen sink, laundry tub, in
a wet basement; or near a swimming pool; and other
areas located near water.
6. Clean only with dry cloth. - Unplug this product from
the wall outlet before cleaning. Do not use liquid
cleaners.
PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNERʼS MANUAL. AND
THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
apparatus. When a cart is used, use caution when
moving the cart/product combination to avoid
injury from tip-over.
Do not block any ventilation openings. Install in
7.
accordance with the manufacturerʼs instructions. -
and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to
protect it from over- heating. The openings should never
be blocked by placing the product on a bed, sofa, rug or
other similar surface. This product should not be placed
in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
manufacturerʼs instructions have been adhered to.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
o not defeat the safety purpose of the polarized or
9. D
grounding-type plug. A polarized plug has two
with one wider than the other. A grounding
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete
outlet.
blades
type plug
Slots
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
Refer all servicing to qualified service personnel.
14.
Servicing is required when the product has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the product has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
3
Contents
Introduction . . . . . . . . . . . . . . . . . . .5-8
About the Symbol Display . . . . . . . . . . . . . .5
Symbol Used in this Manual . . . . . . . . . . . . . . .5
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . .5
Handling Discs . . . . . . . . . . . . . . . . . . . . . . . .5
Storing Discs . . . . . . . . . . . . . . . . . . . . . . . . .5
Cleaning Discs . . . . . . . . . . . . . . . . . . . . . . . .5
Types of Playable Discs . . . . . . . . . . . . . . . . . .6
Regional Code . . . . . . . . . . . . . . . . . . . . . . . . . .6
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . .8
Remote Control operation . . . . . . . . . . . . . . .8
Remote Control Battery installation . . . . . . . .8
Installation and Setup . . . . . . . . .9-15
Setting up the Player . . . . . . . . . . . . . . . . . . . . .9
DVD Player Connections . . . . . . . . . . . . . . .9-10
Video and Audio Connections to Your TV . . .9
Resolution setting . . . . . . . . . . . . . . . . . . . . . .9
HDMI connection . . . . . . . . . . . . . . . . . . . . .10
Audio Connection to Optional Equipment . .11
Displaying Disc Information on-screen . . . . .12
Initial Settings . . . . . . . . . . . . . . . . . . . . . . .12-15
General Operation . . . . . . . . . . . . . . . . . . . .12
LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . .13
• Menu Language . . . . . . . . . . . . . . . . . .13
• Disc Audio / Subtitle / Menu . . . . . . . . .13
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . .13
• TV Aspect . . . . . . . . . . . . . . . . . . . . . . .13
• Display Mode . . . . . . . . . . . . . . . . . . . . .13
AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
• Dolby Digital / DTS / MPEG . . . . . . . . .14
• Sample Freq. (Frequency) . . . . . . . . . .14
• DRC (Dynamic Range Control) . . . . . . .14
• Vocal . . . . . . . . . . . . . . . . . . . . . . . . . . .14
OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . .15
• PBC . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
• B.L.E. (Black Level Expansion) . . . . . . .15
• DivX(R) VOD . . . . . . . . . . . . . . . . . . . . .15
Operations . . . . . . . . . . . . . . . . .16-22
General Features . . . . . . . . . . . . . . . . . . . . . . .16
Additional Features . . . . . . . . . . . . . . . . . . . . .17
Playing an Audio CD or MP3/WMA file . . . . .18
Programmed Playback . . . . . . . . . . . . . . . . . .19
Repeat Programmed Tracks . . . . . . . . . . . .19
Erasing a Track from Program List . . . . . . .19
Erasing the Complete Program List . . . . . . .19
Viewing a JPEG file . . . . . . . . . . . . . . . . . . . . .20
Slide Show . . . . . . . . . . . . . . . . . . . . . . . . . .20
Still Picture . . . . . . . . . . . . . . . . . . . . . . . . . .20
Moving to another file . . . . . . . . . . . . . . . . . .20
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Rotating the picture . . . . . . . . . . . . . . . . . . .20
Listening to MP3 music
while watching picture . . . . . . . . . . . . . . . . .20
Playing a DivX Movie file . . . . . . . . . . . . . . . .21
Playing a DVD VR format Disc . . . . . . . . . . . .22
Reference . . . . . . . . . . . . . . . . . . .23-27
Remote Control Function
Maintenance and Service . . . . . . . . . . . . . . . . .23
Language Codes . . . . . . . . . . . . . . . . . . . . . . . .24
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .25
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Warranty (Only in U.S.A.) . . . . . . . . . . . . . . . . .27
. . . . . . . . . . . . . . . . . . . .
23
4
Introduction
To ensure proper use of this product, please read this
ownerʼs manual carefully and retain it for future
reference.
This manual provides information on the operation
and maintenance of your DVD player. Should the unit
require service, contact an authorized service location.
About the Symbol Display
“ ” may appear on your TV display during
operation and indicates that the function explained in
this ownerʼs manual is not available on that specific
DVD video disc.
Symbol Used in this Manual
Note:
Indicates special notes and operating features.
Tip:
Indicates tips and hints for making the task easier.
A section whose title has one of the following symbols is
applicable only to the disc represented by the symbol.
ALL
All discs and file listed below
DVD
DVD and finalized DVD±R/RW
VCD
Video CDs
ACD
Audio CDs
MP3
MP3 files
WMA
DivX
WMA files
DivX files
Notes on Discs
Handling Discs
Do not touch the playback side of the disc. Hold the
disc by the edges so that fingerprints do not get on
the surface. Never stick paper or tape on the disc.
Storing Discs
After playing, store the disc in its case. Do not expose
the disc to direct sunlight or sources of heat and never
leave it in a parked car exposed to direct sunlight.
Cleaning Discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center out.
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
Introduction
Installation and Setup
Operation
5
Reference
Types of Playable Discs
Regional Code
DVD
(8 cm / 12 cm disc)
Video CD (VCD/SVCD)
(8 cm / 12 cm disc)
Audio CD
(8 cm / 12 cm disc)
In addition, this unit plays DVD±R/RW and CD-R/RW,
Dual disc that contains audio titles, DivX, MP3, WMA,
and/or JPEG files.
This indicates a product feature that is
capable of playing DVD-RW discs
recorded with Video Recording format.
Notes:
• Depending on the conditions of the recording
equipment or the CD-R/RW (or DVD±R/RW) disc
itself, some CD-R/RW (or DVD±R/RW) discs
may not be played on the unit.
• Do not use irregularly shaped CDs (e.g., heartshaped or octagonal) since they may result in
malfunctions.
• This DVD player requires discs and recordings to
meet certain technical standards in order to achieve
optimal playback quality. Pre-recorded DVDs are
automatically set to these standards. There are
many different types of recordable disc formats
(including CD-R containing MP3 or WMA files) and
these require certain pre-existing conditions (see
above) to ensure compatible playback.
Customers should note that permission is
required in order to download MP3 / WMA files
and music from the Internet. Our company has
no right to grant such permission. Permission
should always be sought from the copyright
owner.
This unit has a regional code printed on the rear of the
unit. This unit can play only DVD discs labelled as the
same as the rear of the unit or “ALL”.
Notes on Regional Codes
• Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This
number must match your unitʼs regional code or the
disc cannot play.
• If you try to play a DVD with a different regional
code from your player, the message “Check
Regional Code” appears on the TV screen.
Notes on Copyrights:
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent copyrighted
material without permission. This product features the
copy protection function developed by Macrovision.
Copy protection signals are recorded on some discs.
When recording and playing the pictures of these
discs picture noise will appear. This product
incorporates copyright protection technology that is
protected by method claims of certain U.S. patents
and other intellectual property rights owned by
Macrovision Corporation and other rights owners.
The Use of this copyright protection technology must
be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is
prohibited.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE. IN CASE OF 525 PROGRESSIVE SCAN
PICTURE PROBLEMS, IT IS RECOMMENDED THAT
THE USER SWITCH THE CONNECTION TO THE
ʻSTANDARD DEFINITIONʼ OUTPUT. IF THERE ARE
QUESTIONS REGARDING OUR TV SET
COMPATIBILITY WITH THIS MODEL 525p DVD
PLAYER, PLEASE CONTACT OUR CUSTOMER
SERVICE CENTER.
6
Front Panel
ab cdefghij
Introduction
a 1/' STANDBY/ON
Switches the unit ON and OFF.
b Disc Tray
Insert a disc here.
c Display window
Shows the current status of the unit.
d Remote Sensor
Point the remote control here.
e Z (OPEN/CLOSE)
Opens or closes the disc tray.
f OUTPUT STATUS
You can change the resolution depending on your
TV.
g x (STOP)
Stops playback.
h N (PLAY)
Starts playback.
i . (SKIP)
Returns to the beginning of current chapter or
track or go to the previous chapter or track.
j > (SKIP)
Go to the next chapter or track.
Installation and Setup
Operation
7
Reference
Remote Control
STANDBY/ON (1/')
Switches DVD Player ON and OFF.
OPEN/CLOSE (Z)
Opens and closes the disc tray.
PAUSE/STEP ( X )
Pauses playback temporarily/ press
repeatedly for frame-by-frame
playback.
SKIP (. / >)
Go to next chapter or track.
Returns to the beginning of current
chapter or track or go to the
previous chapter or track.
STOP (x)
Stops playback.
SCAN (m / M)
Search backward or forward.
PLAY (N)
Starts playback.
0-9 numerical buttons
Selects numbered items in a menu.
PROGRAM
Enter to program edit mode.
CLEAR
Removes a track number on the
Program List or a mark on the
Marker Search menu
Remote Control operation
Point the remote control at
the remote sensor and press
the buttons.
Caution:
Do not mix old and new
batteries and never mix
different types of batteries
such as standard, alkaline,
etc.
.
Remote Control Battery
installation
Detach the battery
cover on the rear
AAA
of the remote
AAA
control, and insert
two batteries (size
AAA) with 3 and
# aligned
correctly.
DISPLAY
Accesses On-Screen Display.
DVD MENU
Accesses menu on a DVD disc.
b / B / v / V (left/right/up/down)
Selects an item in the menu.
ENTER ( )
Confirms menu selection.
SETUP
Accesses or removes Setup menu.
RETURN (O)
Displays the menu of a video CD
with PBC.
AUDIO ( )
Selects an audio language or an
audio channel.
SUBTITLE ( )
Selects a subtitle language.
ANGLE ( )
Selects a DVD camera angle,
if available.
ZOOM
Enlarges video image.
MARKER
Marks any point during playback.
SEARCH
Displays MARKER SEARCH menu.
TITLE
Displays title menu, if available.
REPEAT
Repeats chapter, track, title or all.
RANDOM
Plays tracks in random order.
A-B
Repeats sequence from point A to
point B.
8
Installation and Setup
Setting up the Player
The picture and sound of a nearby TV, VCR, or radio
may be distorted during playback. If this occurs,
position the player away from the TV, VCR, or radio,
or turn off the unit after removing the disc.
DVD Player Connections
Depending on your TV and other equipment there are
various ways you can connect the player. Please refer
to the manuals of your TV, stereo system or other
devices as necessary for additional connection
information.
Rear of TV
Rear of
DVD Player
Video and Audio Connections
to Your TV
Make sure the DVD player is connected directly to the
TV and not to a VCR, otherwise the DVD image could
be distorted by the copy protection system.
S-Video – Connect the S-VIDEO OUT jack on the
DVD Player to the S-Video in jack on the TV using
the S-Video cable (S).
Video – Connect the VIDEO OUT jack on the
DVD player to the video in jack on the TV using
the video cable (V).
Audio – Connect the left and right AUDIO OUT
jacks of the DVD Player to the audio left and right
IN jacks on the TV using the audio cables (A).
Do not connect the DVD Playerʼs AUDIO OUT jack
to the phone in jack (record deck) of your audio
system.
Component Video – Connect the COMPONENT /
PROGRESSIVE SCAN jacks on the DVD Player
to the corresponding jacks on the TV using an Y
B PR cable (C).
P
Progressive Scan
• If your television is a high-definition or “digital
ready” television, you may take advantage of
the DVD playerʼs progressive scan output for
the highest possible video resolution.
• Progressive scan does not work with the
analog video connections (yellow VIDEO OUT
jack and S-VIDEO OUT jack).
• The 720p and 480p resolutions are the
progressive scan applied resolution.
Resolution setting
1. Before you set the resolution, this unit must be in
stop mode. Press STOP (x) to stop playback.
2. Press OUTPUT STATUS once. The current
resolution setting will be appears in the display
window.
3. Press OUTPUT STATUS repeatedly to change the
resolution you want.
The available resolution according to the connections
are as shown below.
OUTPUT CONNECTION
HDMI
VIDEO OUT
COMPONENT
VIDEO OUT
VIDEO OUT
S-VIDEO
Notes:
• For Video and S-VIDEO connections, resolution
must be set to 480i or 480p by pressing OUTPUT
STATUS button, however Video OUT and S-Video
OUT is always at 480i standard resolution.
• If your TV does not accept your resolution setting,
abnormal picture appears on the screen.
Please read TVʼs ownerʼs manual then set the
resolution that your TV can accept.
• For 720p and 1080i resolution on the component
video out, only non-copy protected discs can be
played back. If the disc is copy protected, it will be
displayed at the 480p resolution without HDMI
cable connection. With HDMI cable connection, the
picture may not be displayed properly.
Available Resolution
1920 x 1080i
1280 x 720p
720 x 480p
720 x 480i
1920 x 1080i
1280 x 720p
720 x 480p
720 x 480i
720 x 480i
720 x 480i
Introduction
Installation and Setup
Operation
Reference
9
HDMI connection
If you have an HDMI TV or a monitor, you can
connect it to this player using an HDMI cable.
1. Set the TVʼs source to HDMI (refer to TV Ownerʼs
manual).
2. Connect the HDMI OUT jack on the unit to the
HDMI jack on a HDMI compatible TV or
monitor (H).
3. Press OUTPUT STATUS repeatedly to select the
desired resolution.
HDMI compatible TV
Notes:
• Both PCM and Bitstream Audio out is available
when the sample frequency is set to 48kHz in HDMI
connection.
• If Audio setup is set to bitstream and your TV does
not support Bitstream Audio out in HDMI
connection, audio sound may not be outputted or
distorted.
• When the no sound or noisy sound are outputted
with HDMI connection, set the Audio option [Dolby
Digital, DTS or MPEG] in SETUP menu to PCM or
Off.
• The arrow on the cable connector body should face
up for correct alignment with the connector on the
player.
• If there is noise or lines on the screen, please
check the HDMI cable.
• Not all HDCP-compatible DVI devices will work with
this unit.
• If your HDMI TV does not support HDCP,
the blue screen appears on the screen.
• If the abnormal picture appears on the TV screen,
turn off the unit and then turn the unit on again.
Rear of DVD player
About HDMI
HDMI (High Definition Multimedia Interface) supports
both video and audio on a single digital connection for
use with DVD Players, Set-Top Boxes, and other AV
devices.
HDMI was developed to provide the technologies of
HDCP (High-bandwidth Digital Content Protection).
HDCP is used to protect digital content transmitted
and received.
HDMI has the capability to support standard,
enhanced or high-definition video plus standard to
multi-channel surround-sound audio, HDMI features
include uncompressed digital video, a bandwidth of up
to 5 gigabytes per second, one connector (instead of
several cables and connectors), and communication
between the AV source and AV devices such as
DTVs.
HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI licensing LLC.
Tips:
• When you use HDMI connection, you can change
the resolution (480i, 480p, 720p, 1080i) for the
HDMI output.
• The HDMI will be outputted at 480p resolution, even
if you set the resolution to 480i on the HDMI
connection.
10
Audio Connection to Optional
Equipment
Connect the DVD player to your optional equipment
for audio output.
Rear of DVD Player
Amplifier (Receiver)
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and
the double-D symbol are trademarks of
Dolby Laboratories.
DTS and DTS Digital Out are trademarks
of Digital Theater Systems, Inc.
Amplifier equipped with 2-channel analog stereo
or Dolby Pro Logic ll / Pro Logic: Connect the left
and right AUDIO OUT jacks on the DVD player to the
audio left and right IN jacks on your amplifier,
receiver, or stereo system, using the audio cables (A).
Amplifier equipped with 2-channel digital stereo
(PCM) or audio / video receiver equipped with a
multi-channel decoder (Dolby Digital™, MPEG 2,
or DTS):
Connect one of the DVD Playerʼs DIGITAL AUDIO
OUT jacks (OPTICAL O or COAXIAL X) to the
corresponding jack on your amplifier. Use an optional
digital (OPTICAL O or COAXIAL X) audio cable.
Digital Multi-channel sound
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel audio
/ video receiver that supports one or more of the
audio formats supported by your DVD player such as
MPEG 2, Dolby Digital and DTS. Check the receiver
manual and the logos on the front of the receiver.
Notes:
• If the audio format of the digital output does not
match the capabilities of your receiver, the receiver
produces a strong, distorted sound or no sound at
all.
• Six Channel Digital Surround Sound via a digital
connection can only be obtained if your receiver is
equipped with a Digital Multi-channel decoder.
Introduction
Installation and Setup
Operation
Reference
11
Displaying Disc Information
on-screen
You can display various information about the disc
loaded on-screen.
1. Press DISPLAY to show various playback
information.
The displayed items differ depending on the disc
type or playing status.
Initial Settings
By using the Setup menu, you can make various
adjustments to items such as picture and sound.
You can also set a language for the subtitles and the
Setup menu, among other things. For details on each
Setup menu item, see pages 13 to 15.
To display and exit the Menu:
Press SETUP to display the menu. A second press of
SETUP will take you back to initial screen.
To go to the next level:
Press B on the remote control.
To go back to the previous level:
Press b on the remote control.
General Operation
1. Press SETUP.
The Setup menu appears.
2. You can select an item by pressing v / V and
change or select the setting by pressing b / B.
• Title (Track) – Current title (or track).
number/total number of titles (or tracks).
• Chapter – Current chapter number/total number
of chapters.
• Time – Elapsed playing time.
• Audio – Selected audio language or channel.
• Subtitle – Selected subtitle.
• Angle – Selected angle/total number of angles.
Note:
If any button is not pressed for a few seconds, the onscreen display disappears.
2. Use v / V to select the desired option then press
B to move to the second level. The screen shows
the current setting for the selected item, as well as
alternate setting(s).
3. Use v / V to select the second desired option and
then press B to move to the third level.
4. Use v / V to select the desired setting then press
ENTER to confirm your selection.
Some items require additional steps.
5. Press SETUP or PLAY (N) to exit the Setup
menu.
12
LANGUAGE
DISPLAY
Introduction
Menu Language
Select a language for the Setup menu and then
on-screen display.
Disc Audio / Subtitle / Menu
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
Original – Refers to the original language in which
the disc was recorded.
Other – To select another language, press
numeric buttons and then ENTER to enter the
corresponding 4-digit number according to the
language code list on the page 24. If you enter the
wrong language code, press CLEAR.
Off (for Disc Subtitle) – Turn off Subtitle.
TV Aspect
4:3 – Select when a standard 4:3 TV is connected.
16:9 – Select when a 16:9 wide TV is connected.
Display Mode
The Display Mode setting works only when the TV
Aspect mode is set to 4:3.
Letterbox – Displays a wide picture with bands on
the upper and lower portions of the screen.
Panscan – Automatically displays the wide picture
on the entire screen and cuts off the portions that
do not fit.
Installation and Setup
Operation
Reference
13
AUDIO
Each DVD disc has a variety of audio output options.
Set the playerʼs AUDIO options according to the type
of audio system you use.
Dolby Digital / DTS / MPEG
Bitstream – Select “Bitstream” if you connect this
unitʼs DIGITAL OUT jack to an amplifier or other
equipment with a Dolby Digital, DTS or MPEG
decoder.
PCM (for Dolby Digital / MPEG) – Select when
connected to a two-channel digital stereo amplifier.
DVDs encoded in Dolby Digital, MPEG will be
automatically downmixed to two-channel PCM
audio.
Off (for DTS) – If you select “Off”, the DTS signal
is not output through the DIGITAL OUT jack.
DRC (Dynamic Range Control)
With the DVD format, you can hear a programʼs
soundtrack in the most accurate and realistic
presentation. However, you may wish to compress the
dynamic range of the audio output (the difference
between the loudest sounds and the quietest ones).
This allows you to listen to a movie at a lower volume
without losing clarity of sound.
Set DRC to On for this effect.
Vocal
Set to On only when a multi-channel karaoke DVD is
playing. The karaoke channels on the disc mix into
normal stereo sound.
Sample Freq. (Frequency)
If your receiver or amplifier is NOT capable of
handling 96 kHz signals, select 48 kHz. When this
choice is made, this unit automatically converts any
96 kHz signals to 48 kHz so your system can decode
them.
If your receiver or amplifier is capable of handling 96
kHz signals, select 96 kHz.
Check the documentation for your amplifier to verify
its capabilities.
14
OTHERS
PBC
Set Playback Control (PBC) to On or Off.
On: Video CDs with PBC are played according to
the PBC.
Off: Video CDs with PBC are played in the same
way as Audio CDs.
B.L.E. (Black Level Expansion)
To select the black level of playback pictures.
Set your preference and monitorʼs ability.
On: Expanded grey scale. (0 IRE cut off)
Off: Standard grey scale. (7.5 IRE cut off)
Introduction
Installation and Setup
DivX(R) VOD
®
We provide you the DivX
registration code that allows you to rent and purchase
videos based on the DivX
information, visit www.divx.com/vod.
1. Select “DivX(R) VOD” option and then press B.
2. Press ENTER while “Select” is selected and the
registration code will appear.
Use the registration code to purchase or rent the
videos from DivX
www.divx.com/vod. Follow the instructions and
download the video onto a disc for playback on
this unit.
3. Press ENTER to exit.
Note:
All the downloaded videos from DivX
be played back on this unit.
VOD (Video On Demand)
®
VOD service. For more
®
VOD service at
®
VOD can only
Operation
Reference
15
Operations
General Features
Buttons Operations
OPEN/CLOSE (Z) Opens or closes the disc tray.
PAUSE/STEP (X) During playback, press PAUSE/STEP (X) to pause
playback.
Press PAUSE/STEP (X) repeatedly to play Frame-byFrame.
SKIP (. / >) During playback, press SKIP (. or >) to go to the
next chapter/track or to return to the beginning of the
current chapter/track.
Press SKIP (.) twice briefly to step back to the
previous chapter/track.
SCAN (m / M) During playback, press SCAN (m or M) repeatedly to
select the required scan speed.
DVD, DivX disc; 4 steps
Video CD, MP3, Audio CD ; 3 steps
While the playback is paused, press SCAN (M)
repeatedly to play in slow motion (4 steps, forward only).
REPEAT During playback, press REPEAT repeatedly to select a
desired repeat mode.
DVD Video discs: Chapter/Title/Off
Video CD, Audio CD, DivX/MP3/WMA discs: Track/All/Off
A-B Press the A-B button one at a time to select a point A and
point B and repeats a sequence from point A (Starting
point) to point B (End point).
ZOOM During playback or pause mode, press ZOOM to enlarge
the video image (3 steps).
You can move through the zoomed picture using
b / B / v / V buttons. Press CLEAR to exit.
RANDOM During playback or in stop mode, press RANDOM for
random playback.
TITLE If the current DVD title has a menu, the title menu
appears on the screen. Otherwise, the disc menu may
appears.
DVD MENU The disc menu appears on the screen.
ANGLE ( ) During playback of DVD disc that contains scenes
recorded at different camera angles, press ANGLE ( )
repeatedly to select a desired angle.
SUBTITLE ( ) During playback, press SUBTITLE ( ) r epeatedly to
select a desired subtitle language.
Discs
ALL
ALL
DVD VCD
ALL
DVD VCD
ACD MP3
DVD
ALL
DVD VCD
DivX
DVD VCD
ACD MP3
DVD
DVD
DVD
DVD
DivX
DivX
DivXVCD
ACD
DivX
WMA
DivX
AUDIO ( ) During playback, press AUDIO ( ) repeatedly to hear
a different audio language, audio channel or encording
method.
16
DVD
DivX
VCD
Notes on general features:
• On a Video CD with PBC, you must set PBC to Off
on the setup menu to use the repeat function (See
“PBC” on page 15).
• If you press SKIP (>) once during Repeat Chapter
(Track) playback, the repeat playback cancels.
• Zoom may not work on some DVDs.
• When you are playing a DVD disc that contains
scenes recorded at different camera angles, the
angle indicator will be displayed on the TV screen
during the operations as an indication that angle
switching is possible.
• The A-B repeat function is available only in the
current track of the Audio CD.
Additional Features
Last Scene Memory
This player memorizes last scene from the last disc
that is viewed. The last scene remains in memory
even if you remove the disc from the player or switch
off the player. If you load a disc that has the scene
memorized, the scene is automatically recalled.
Note:
This player does not memorize the scene of a disc if
you switch off the player before commencing to play
the disc.
Screen Saver / Auto Power Off
The screen saver appears when you leave the DVD
player in Stop mode for about five minutes. If the
Screen Saver is displayed for five minutes, the DVD
Player automatically turns itself off.
ACDVCDDVD
Time Search
To start playing at any chosen time on the disc:
1. Press DISPLAY during playback.
2. Press v / V to select the time clock icon and
“--:--:--” appears.
3. Input the required start time in hours, minutes, and
seconds from left to right. If you enter the wrong
numbers, press CLEAR to remove the numbers
you entered. Then input the correct numbers.
4. Press ENTER to confirm.
Playback starts from the selected time.
Marker Search
To enter a Marker
You can start playback from up to nine memorized
points. To enter a marker, press MARKER at the
desired point on the disc. The Marker icon appears on
the TV screen briefly. Repeat to enter up to nine
markers.
To Recall or Clear a Marked Scene
1. During disc playback, press SEARCH. The marker
search menu appears on the screen.
2. Within 9 seconds, press b / B to select a marker
number that you want to recall or clear.
3. Press ENTER and playback starts from the marked
scene. Or, Press CLEAR and the marker number is
erased from the list.
4. You can play any marker by inputting its number on
the marker search menu.
DivXVCDDVD
DivXVCDDVD
Operation
17
Playing an Audio CD or
MP3/WMA file
This unit can play Audio CDs or MP3/WMA files.
MP3/ WMA/ Audio CD
Once you insert an MP3/WMA files recorded media or
Audio CD, a menu appears on the TV screen.
Use v / V to select a track/file and then press
PLAY (N) or ENTER and playback starts.
You can use variable playback functions.
Refer to page 16-17.
ID3 TAG
When playing a file containing information such as
track titles, you can see the information by pressing
DISPLAY. [ Song, Artist, Album, Comment, Genre ]
Tips:
• Press DVD MENU to move to the next page.
• On a DISC with MP3/WMA, JPEG and MOVIE file,
you can switch MUSIC, PHOTO and MOVIE menu.
Press TITLE, and MUSIC, PHOTO or MOVIE word
on top of the menu is highlighted.
MP3 / WMA disc compatibility with this player is
limited as follows:
• Sampling frequency: within 8 - 48 kHz (MP3),
within 32 - 48kHz (WMA)
• Bit rate: within 8 - 320kbps (MP3),
32 - 384 kbps (WMA)
• The player cannot read an MP3/WMA file that has
a file extension as non than “.mp3” / “.wma”.
• CD-R physical format should be ISO 9660
• If you record MP3 / WMA files using software that
cannot create a file system (eg. Direct-CD) it is
impossible to playback MP3 / WMA files.
We recommend that you use Easy-CD Creator,
which creates an ISO 9660 file system.
• File names should have a maximum of 8 letters
and must incorporate an .mp3 or .wma extension.
• They should not contain special letters such as / ?
* : “ < > l etc.
• The total number of files in a folder should be less
than 1012 files.
18
Programmed Playback
The program function enables you to store your
favorite tracks from any disc in the player memory.
A program can contain 30 tracks.
1. Insert an Audio CD or MP3/WMA files recorded
media. AUDIO CD or MUSIC menu appears.
2. Press PROGRAM and the mark will appear.
Note:
Press PROGRAM again to exit the program edit
mode, then the mark will disappear.
E
3. Select a track on the “List” and then press ENTER
to place the selected track on the “Program” list.
Repeat to place additional tracks on the list.
4. Use b / B / v / V to select the track you want to
start playing on the “Program” list.
5. Press PLAY (N) or ENTER to start.
Playback begins in the order in which you
programmed the tracks. Playback stops after all of
the tracks on the “Program” list have played once.
6. To resume normal playback from programmed
playback, select a track on the list and then press
PLAY (N).
E
Repeat Programmed Tracks
Press REPEAT to select a desired repeat mode.
• Track: Repeats the current track.
• All: Repeats all the tracks on programmed list.
• Off(No display): Does not play repeatedly.
Note:
If you press SKIP (>) once during Repeat Track
playback, the repeat playback cancels.
Erasing a Track from Program List
1. During stop mode, press PROGRAM and the
E
mark will appear
2. Use b / B / v / V to select the track that you wish
to erase from the Program list.
3. Press CLEAR. Repeat step 1-3 to erase additional
tracks on the list.
Erasing the Complete Program List
1. During stop mode, press PROGRAM and the
E
mark will appear
2. Use b / B / v / V to select “Clear All” and then
press ENTER.
Note:
The programs are also cleared when the power is
off or the disc is removed.
Operation
19
Viewing a JPEG file
This unit can play JPEG files.
1. Insert a JPEG files recording media.
The PHOTO menu appears on the TV screen.
2. Press v / V to select a folder, and press ENTER.
A list of files in the folder appears.
3. If you want to view a particular file, press v / V to
highlight a file and press ENTER or PLAY (N).
4. To return to the PHOTO menu while watching
pictures, press STOP (x).
Tips:
• If you are in a file list and want to return to the
previous Folder list, use v / V buttons to highlight
and press ENTER.
• Press DVD MENU to move to the next page.
• There are three Slide Speed options:
>>> (Fast), >> (Normal) and > (Slow).
Use b / B / v / V to highlight . Then, use b / B
to select the option you want to use.
• On a DISC with MP3/WMA, JPEG and MOVIE file,
you can switch MUSIC, PHOTO and MOVIE menu.
Press TITLE, and MUSIC, PHOTO or MOVIE word
on top of the menu is highlighted.
• While watching a picture, press RETURN (O) to
hide the help menu.
• When viewing a JPEG file, the help menu will not
be displayed on the TV screen if the resolution is
set to 720p or 1080i.
Slide Show
Use b / B / v / V to highlight the (Slide Show)
then press ENTER.
Still Picture
1. Press PAUSE/STEP (X) during slide show.
The player will now go into pause mode.
2. To return to the slide show, press PLAY (N) or
press PAUSE/STEP (X) again.
Moving to another file
Press SKIP (. or >) or cursor (b or B) once
during viewing a picture to advance to the next or
previous file.
Zoom
During watching pictures, press ZOOM to enlarge the
video image (3 steps). You can move through the
zoomed picture using b / B / v / V buttons.
Note:
When the resolution is set to 720p or 1080i, this
function is not available.
Rotating the picture
Press v / V during showing a picture to rotate the
picture clockwise or counter clockwise.
Listening to MP3 music while watching picture
1. Insert the disc containing the two types of file in
the player.
2. Press TITLE to display the PHOTO menu.
3. Press v / V to select a photo file.
4. Use B to select icon then press ENTER.
Playback starts.
5. To return to the PHOTO menu while watching
pictures, press STOP (x).
Note:
When the resolution is set to 720p or 1080i, this
function is not available.
Tip:
To listen to only the desired music while watching
picture, program the desired files from the “MUSIC”
menu and then proceed as above.
JPEG disc compatibility with this player is
limited as follows:
• Depending upon the size and the number of
JPEG files, it could take a long time for the DVD
player to read the discʼs contents. If you do not
see an on-screen display after several minutes,
some of the files may be too large — reduce the
resolution of the JPEG files to less than 5 million
pixels and burn another disc.
• The total number of files in a folder should be less
than 1012 files.
• Some discs may be incompatible due to a
different recording format or the condition of disc.
• Ensure that all the selected files have the “.jpg”
extensions when copying into the CD layout.
• If the files have “.jpe” or “.jpeg” extensions, please
rename them as “.jpg” file.
• File names without “.jpg” extension will not be
able to be read by this unit. Even though the files
are shown as JPEG image files in Windows
Explorer.
20
Playing a DivX Movie file
Using this DVD Player you can play DivX file.
1. Insert a DivX file recording media.
The MOVIE menu appears on the TV screen.
2. Press v / V to select a folder, and press
ENTER. A list of files in the folder appears.
3. If you want to view a particular file, press v / V to
highlight a file and press ENTER or PLAY (N).
You can use variable playback functions.
Refer to page 16-17.
4. Press STOP (x) to stop the playback.
The MOVIE menu appears.
Tips:
• If you are in a file list and want to return to the
previous Folder list, use the v / V buttons on the
remote to highlight and press ENTER.
• Press DVD MENU to move to the next page.
• On a CD with MP3/WMA, JPEG and MOVIE file,
you can switch MUSIC, PHOTO and MOVIE menu.
Press TITLE, and MUSIC, PHOTO or MOVIE word
on top of the menu is highlighted.
• The disc subtitle may not be displayed properly, if a
DivX subtitle is downloaded through the internet.
• If the Disc Subtitle setup menu does not have the
DivX subtitle language you are going to play, the
subtitle may not be displayed properly.
Notice for displaying the DivX subtitle
If the subtitle does not display properly, please follow
the steps below.
1. Press and hold SUBTITLE ( ) for about
3 seconds. The language code will appear.
2. Press b / B to select another language code until
the subtitle is displayed properly.
3. Press ENTER.
Note:
The DivX subtitle file name has to be identified with
the DivX file name to display by this unit.
DivX disc compatibility with this player is limited
as follows:
• Available resolution size of the DivX file is under
720x576 (W x H) pixel.
• The file name of the DivX subtitle is available by
56 characters.
• If there is impossible code to express in the DivX
file, it may be displayed as “ _ ” mark on the
display.
• If the number of the screen frame is over 30
per 1 second, this unit may not operate
normally.
• If the video and audio structure of recorded
file is not interleaved, either video or audio is
outputted.
• If the file is recorded with GMC, the unit
supports only 1-point of the record level.
GMC?
*
GMC is the acronym for Global Motion
Compensation. It is an encoding tool specified in
MPEG4 standard. Some MPEG4 encoders, like
DivX have this option.
There are different levels of GMC encoding,
usually called 1-point, 2-point, or 3-point GMC.
Playable DivX file
.avi, .mpg, .mpeg
Playable Subtitle format
SubRip(*.srt/*.txt)
SAMI(*.smi)
SubStation Alpha(*.ssa/*.txt)
MicroDVD(*.sub/*.txt)
SubViewer 1.0(*.sub)
SubViewer 2.0(*.sub/*.txt)
TMPlayer(*.txt)
Playable Codec format
“DIVX3.xx”, “DIVX4.xx”, “DIVX5.xx”, “MP43”, “3IVX”.
Playable Audio format
“Dolby Digital”, “DTS”, “PCM”, “MP3”, “WMA”.
• Sampling frequency: within 8 - 48 kHz (MP3),
within 32 - 48kHz (WMA)
• Bit rate: within 8 - 320kbps (MP3),
32 - 384kbps (WMA)
• Not all the WMA Audio format is compatible with
this unit.
Operation
21
Playing a DVD VR format Disc
This unit will play DVD-RW disc that is recorded
using the Video Recording (VR) format.
1. Insert a disc and close the tray.
It start playing automatically.
2. The DVD-VR menu appears on the TV screen
when you press DVD MENU buttons while playing.
3. Press v / V to select a track then press
PLAY (N) or ENTER and playback starts.
4. Press DVD MENU to move to the list menu.
Notes:
• The slow motion function is not available.
• This unit will play DVD-R/RW disc that is recorded
using the DVD-Video format that have been
finalized using a DVD-recorder. Unfinalized DVDR/RW discs cannot be played in this player.
• Some DVD-VR disc are made with CPRM data by
DVD RECORDER. Player does not support these
kinds of discs
What is CPRM?
CPRM is a copy protection system (with scramble
system) only allowing the recording of ʻcopy onceʼ
broadcast programs. CPRM stands for Content
Protection for Recordable Media.
.
22
Reference
Remote Control Function
Remote Control C1/C2/C3 Code Switching
This unit is initially set to C3 code (JVC DVD
PLAYER code). You can easily change the
Remote Control code to C1 (JVC VCR code), C2
(JVC DVD RECORDER code) or C3 as shown
below.
STANDBY/ON
ENTER
1-3
• Keep pressing ENTER down during step 1.
1. Press the number Key “1” for C1, “2” for C2 or
“3” for C3 to change the remote control code.
2. Press STANDBY/ON (
x
3. Press
unit is turned on. The code currently set appears
on the front display panel.
4. Press ENTER on the remote control to change the
unit's code. The code currently set on the remote
control is displayed on the front display panel for
approximately 5 seconds, and is applied to the
unit.
Note:
If you change the batteries of the Remote Control with
C1 or C2 code, the remote control code is set to C3
automatically. In this case, you should reset the
remote control code described above.
on the unit for over 5 seconds while the
1/\) to turn on the unit.
x
Maintenance and Service
Refer to the information in this chapter before
contacting a service technician.
Handling the Unit
When shipping the unit
Please save the original shipping carton and packing
materials. If you need to ship the unit, for maximum
protection, re-pack the unit as it was originally packed
at the factory.
Keeping the exterior surfaces clean
• Do not use volatile liquids such as insecticide spray
near the unit.
• Do not leave rubber or plastic products in contact
with the unit for a long period of time. since they
leave marks on the surface.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution.
Do not use strong solvents such as alcohol, benzine,
or thinner, as these might damage the surface of the
unit.
Maintaining the Unit
The unit is a high-tech, precision device. If the optical
pick-up lens and disc drive parts are dirty or worn, the
picture quality could be diminished.
Depending on the operating environment, regular
inspection and maintenance are recommended after
every 1,000 hours of use.
For details, please contact your nearest authorized
service center.
Reference
23
Language Codes
Use this list to input your desired language for the following initial settings:
Disc Audio, Disc Subtitle, Disc Menu.
Language Code
Abkhazian 6566
Afar 6565
Afrikaans 6570
Albanian 8381
Ameharic 6577
Arabic 6582
Armenian 7289
Assamese 6583
Aymara 6588
Azerbaijani 6590
Bashkir 6665
Basque 6985
Bengali; Bangla 6678
Bhutani 6890
Bihari 6672
Breton 6682
Language Code
Fiji 7074
Finnish 7073
French 7082
Frisian 7089
Galician 7176
Georgian 7565
German 6869
Greek 6976
Greenlandic 7576
Guarani 7178
Gujarati 7185
Hausa 7265
Hebrew 7387
Hindi 7273
Hungarian 7285
Icelandic 7383
Language Code
Lingala 7678
Lithuanian 7684
Macedonian 7775
Malagasy 7771
Malay 7783
Malayalam 7776
Maltese 7784
Maori 7773
Marathi 7782
Moldavian 7779
Mongolian 7778
Nauru 7865
Nepali 7869
Norwegian 7879
Oriya 7982
Panjabi 8065
Language Code
Singhalese 8373
Slovak 8375
Slovenian 8376
Somali 8379
Spanish 6983
Sudanese 8385
Swahili 8387
Swedish 8386
Tagalog 8476
Tajik 8471
Tamil 8465
Tatar 8484
Telugu 8469
Thai 8472
Tibetan 6679
Tigrinya 8473
Bulgarian 6671
Burmese 7789
Byelorussian 6669
Cambodian 7577
Catalan 6765
Chinese 9072
Corsican 6779
Croatian 7282
Czech 6783
Danish 6865
Dutch 7876
English 6978
Esperanto 6979
Estonian 6984
Faroese 7079
Indonesian 7378
Interlingua 7365
Irish 7165
Italian 7384
Japanese 7465
Javanese 7487
Kannada 7578
Kashmiri 7583
Kazakh 7575
Kirghiz 7589
Korean 7579
Kurdish 7585
Laothian 7679
Latin 7665
Latvian, Lettish 7686
Pashto, Pushto 8083
Persian 7065
Polish 8076
Portuguese 8084
Quechua 8185
Rhaeto-Romance 8277
Rumanian 8279
Russian 8285
Samoan 8377
Sanskrit 8365
Scots Gaelic 7168
Serbian 8382
Serbo-Croatian 8372
Shona 8378
Sindhi 8368
Tonga 8479
Turkish 8482
Turkmen 8475
Twi 8487
Ukrainian 8575
Urdu 8582
Uzbek 8590
Vietnamese 8673
Volapük 8679
Welsh 6789
Wolof 8779
Xhosa 8872
Yiddish 7473
Yoruba 8979
Zulu 9085
24
Troubleshooting
Symptom
No power.
The power is on, but
the DVD player does
not work.
No picture.
No sound.
The DVD player does
not start playback.
Possible Cause
• The power cord is disconnected.
• No disc is inserted.
• The TV is not set to receive DVD
signal output.
• The video cable is not connected
securely.
• The equipment connected with the
audio cable is not set to receive DVD
signal output.
• The power of the equipment
connected with the audio cable is
turned off.
• The AUDIO options are set to the
wrong position.
• An unplayable disc is inserted.
Correction
• Plug the power cord into the wall outlet
securely.
• Insert a disc. (Check the disc indicator
in the display window is lit.)
• Select the appropriate video input
mode on the TV.
• Connect the video cable securely.
• Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD player.
• Turn on the equipment connected with
the audio cable.
• Set the AUDIO option to the correct
position, then turn on the DVD player
again by pressing STANDBY/ON.
• Insert a playable disc. (Check the disc
type and regional code.)
The remote control
does not work properly.
• The remote control is not pointed at
the remote sensor on the DVD player.
• The remote control is too far from the
DVD player.
• The current remote control code does
not match the unit.
• Point the remote control at the remote
sensor of the DVD player.
• Operate the remote control closer to
the DVD player.
• Identify the remote control code with
the code of unit. (See page 23).
Reference
25
Specifications
General
Power requirements: AC 120 V, 60 Hz
Power consumption: 8 W
Dimensions (Approx.): 430 x 35 x 201 mm (17 x 1.4 x 7.9 inches) (W x H x D) without foot
Net weight (Approx.): 1.6 kg (3.5 lbs)
Operating temperature: 5 °C to 35 °C (41 °F to 95 °F)
Operating humidity: 5 % to 90 %
Outputs
VIDEO OUT: 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
S-VIDEO OUT: (Y) 1.0 V (p-p), 75 Ω, negative sync, Mini DIN 4-pin x 1
(C) 0.3 V (p-p) 75 Ω
COMPONENT VIDEO OUT: (Y) 1.0 V (p-p), 75 Ω,negative sync, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2
AUDIO OUT: 2.0 Vrms (1 KHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
DIGITAL OUT (COAXIAL): 0.5 V (p-p), 75 Ω, RCA jack x 1
DIGITAL OUT (OPTICAL): 3 V (p-p), Optical jack x 1
System
Laser: Semiconductor laser, wavelength 650 nm
Signal system: NTSC
Frequency response: DVD (PCM 96 kHz): 8 Hz to 44 kHz
DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz
Signal-to-noise ratio: More than 90 dB (ANALOG OUT connectors only)
Harmonic distortion: Less than 0.02%
Dynamic range: More than 95 dB (DVD/CD)
Accessories
Video cable (1), Audio cable (1), Remote control (1), Batteries (2)
Note: Design and specifications are subject to change without prior notice.
26
Warranty (Only in U.S.A.)
Reference
27
XV-N652S / XV-N650B
Printed in Indonesia
US
0207MNH-0T-0T
P/N: MFL38257001
Loading...