Cautions
Precautions
Concerning Compact Discs
Listening Precautions
• Do not play your headphones at a high volume. Hearing experts advise against continuous extended play.
• If you experience a ringing in your ears, reduce volume or discontinue use.
• Do not use while operating a motorized vehicle. It may create a
traffic hazard and is illegal in many areas.
• You should use extreme caution or temporarily discontinue use
in potentially hazardous situations.
• Even if your headphones is an open-air type designed to let you
hear outside sounds, don’t turn up the volume so high that you
can’t hear what’s around you.
Rechargeable batteries
• Rechargeable batteries (not supplied) can be used.
• To use the rechargeable batteries, follow the instruction manual
attached to the rechargeable batteries and charger (not supplied).
Dry cell batteries
To prevent damage to the batteries and electrolyte leakage, heed
the following points.
• Align the , and . polarities properly when inserting the bat-
teries.
• Do not mix different types or makers of batteries or old and
new batteries.
• Remove the batteries if you do not plan to use the unit for a
long period of time.
• Do not throw batteries into a fire, and do not short-circuit, disassemble or subject them to excessive heat.
• Do not attempt to recharge dry cell batteries.
Carrying dry cell batteries around
When putting dry cell batteries in a pocket or bag, ensure that no
other metal objects such as a necklace are placed together with
them. Contact with metal may cause short-circuiting which, in
turn, may cause a fire.
AC adaptor
• Handle the AC adaptor carefully. Improper handling is dangerous.
• Do not touch it with wet hands.
• Do not place heavy objects on top of it.
• Do not forcibly bend it.
• Be sure to connect only the specified AC adaptor with the unit.
• Disconnect the AC adaptor from the power outlet if the unit is
not going to be used for a long time.
Unit
No altering or remodeling
This can cause malfunctioning.
No dropping or strong impacts
This may damage the unit.
Locations to be avoided
Avoid using the unit in the following locations since they can
cause malfunctioning.
1. Bathrooms and other moisture-prone places.
2. Warehouses and other dusty places
3. Very hot places near heating appliances, etc.
Do not leave the unit exposed to direct sunlight for
long periods of time
This may deform or discolor the cabinet and may also cause malfunctioning.
When purchasing AC adaptor
Be absolutely sure to purchase the AC adaptor designed especially for this unit.
AC adaptor: AA-R4515
For details, check with your dealer.
Safety
1. Care of AC adaptor - The cord of the AC adaptor should be
routed so that they are not likely to be walked on or pinched by
items placed upon or against them. Never take hold of the AC
adaptor if your hand is wet, and always grasp the plug when
connecting or disconnecting it.
2. Disconnect when not in use - When not in use, be sure to dis-
connect the AC adaptor from the AC power outlet.
3. Batteries - If the unit is not used for a long period of time or is
used only from an AC power source, remove all the batteries to
prevent potential damage due to battery leakage. Do not mix
(old and new ) batteries or different types of batteries.
Installation
■ Environment
1. Condensation - Moisture may form on the lens in the follow-
ing conditions…
• immediately after a heater has been turned on.
• in a steamy or very humid room.
• when the unit is suddenly moved from a cold environment to
a warm one. If moisture forms inside this unit, it may not operate properly. To correct this problem wait about one hour
for the moisture to evaporate.
■ Placement
1. Foreign Material - Care should be taken so that objects do not
fall into and liquids are not spilled into the unit. Do not subject
this unit to excessive smoke, dust, mechanical vibration, or
shock.
2. Magnetism - The unit should be situated away from equipment
or devices that generate strong magnetic fields.
3. Stacking - Do not place any objects on top of the unit.
Maintenance
(See page 5 for details.)
Clean the cabinet, panel and controls with a soft cloth lightly
moistened with mild detergent solution.
Do not use any type of abrasive pad, scouring powder or solvent
such as alcohol or benzine.
Service
1.Damage Requiring Service - The unit should be serviced by
qualified service personnel when:
(a) The AC adaptor is damaged; or
(b) Objects have fallen or liquid has been spilled into the unit; or
(c) The unit has been exposed to rain; or
(d) The unit does not appear to operate normally or exhibits a
marked change in performance; or
(e) The unit has been dropped, or the enclosure damaged.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
Only compact discs bearing this mark can be used with this unit.
However, continued use of irregular shape CDs (heart-shape, octagonal, etc.) can damage
the unit.
CD-R and CD-RW discs recorded with the audio
CD format can be played back, though some may
not be played back because of the disc characteristics or recording condition.
How to remove a disc from its case
How to store the disc in
its case
Label side up
How to hold a disc
If the disk surface is dirty
Wipe it with a damp cloth and then wipe dry.
Wipe from the center toward the outer edge.
Play surface (shiny surface)
If moisture has formed on a disc
When moisture has formed because the
disc was brought suddenly into a warm
room from a cold environment, wipe off
the moisture using a soft dry cloth.
When storing discs
Avoid locations which are
• Exposed to direct sunlight.
• Susceptible to high levels of humidity or
dust.
• Directly exposed to heat from a heating
appliance.
• On top of a car dashboard or near the
rear window.
Handling precautions
• On the label side (the side with writing)
Do not write anything using a pencil,
ball-point pen, etc. Do not use adhesive
paper or labels.
• On the disc (shiny) side
Handle this side carefully to keep it free
from fingerprints or scratches. Do not
use record cleaners, solvents, etc.
• Do not attach labels or stickers to CDs.
Do not use CDs with exposed adhesive
from tape or left over peeled off stickers.
• Do not use scratch-proof protectors or
covers other than those specified for use
with this unit.
PORTABLE CD PLAYER
XL-PG300B
INSTRUCTIONS
Supplied Accessories
Stereo headphones .......................................................................................................................... 1 pc.
Thank you for purchasing this JVC product. Please read these instructions carefully before starting
operation to be sure to obtain optimum performance and a longer service life from the unit.
LVT1178-004A [B]
0304SKMCREORI
©2004 VICTOR COMPANY OF JAPAN, LIMITED
EN
Troubleshooting
Problem
Does not turn on.
Cannot close the lid.
Cannot play discs.
Cannot hear music—too
noisy.
TV picture is distorted.
Radio reception is noisy.
“dISC” or “Er” is displayed
when a disc is in the
player.
If the remedies indicated in the chart do not solve the problem, refer to the directory of Authorized Service Centers (enclosed with this unit) to locate a convenient service center, or consult
your dealer for instructions.
• Is the AC adaptor securely connected?
• Is the HOLD switch set to OFF position?
Is the disc properly secured in place?
• Is the disc properly secured in place?
• Is there moisture condensation on the lens?
(Wait for about an hour and then try again.)
• Is the headphone plug inserted all the way?
• Is the plug dirty? (Wipe away dirt on the plug.)
Are you using the unit too near a TV or tuner? (If the TV or
tuner is connected to a simple indoor antenna, connect it to
an outdoor antenna.)
• Is the disc damaged?
• Is the disc playable on this player?
• Has the disc been inserted upside down?
Check this
Maintenance
Unit
Wipe the unit with a soft cloth. Remove stubborn dirt using a cloth which has been dipped in water or soapy water and wrung out, and then wipe dry.
• If you intend to use a chemically treated cleaning cloth, read its directions first.
• Do not use alcohol or paint thinners.
Lens
Air blower for
camera lens
Lens
CAUTION:
• Do not block the ventilation opening or holes. (If the ventilation openings of holes are blocked by a newspaper or
cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems must
be considered and local rules or laws governing the disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping or
splashing and that no objects filled with liquids, such as vases,
shall be placed on the apparatus.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are
no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation
when open and interlock failed or defeated. Avoid
direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL,
PLACED OUTSIDE THE UNIT.
CAUTION: Visible and invisible
laser radiation when open and
interlock failed or defeated.
AVOID DIRECT EXPOSURE TO
BEAM. (e)
ADVARSEL: Synlig og usynlig
laserstråling når maskinen er
åben eller interlocken fejle.
Undgå direkte eksponering
til stråling. (d)
VARNING: Synlig Och
osynlig laserstrålning när
den öppnas och spärren är
urkopplad. Betrakta ej
strålen. (s)
VARO: Avattaessa ja
Suojalukitus ohitettunatai
viallisena olet alttiina näkyvälle
ja näkymättömälle lasersäteilylle.
Vältä säteen kohdistumista
suoraan itseesi. (f)
Specifications
Portable CD player
Type : Compact disc player
Signal detection system : Non-contact optical pickup (semiconductor laser)
Pickup system : 3 beam laser
Number of channels: : 2 channels (stereo)
Frequency response : 20 Hz to 20 kHz
Wow & flutter : Unmeasurable
Output : Headphones (3.5 mm dia. stereo × 1)
Duration of battery : Approx. 30 hours when using two alkaline batteries (LR6)
(with Anti-Shock
Protection EX OFF)
Power requirements : DC 3 V (“R6” size battery × 2)
Dimensions (W×H ×D) : 133.2 mm × 30.8 mm ×146.8 mm
Mass : 250 g
AC adaptor (not supplied)
Input power source : AC 230 V, 50 Hz
Output voltage : DC 4.5 V, 600 mA
Design and specifications are subject to change without notice.
*
9 mW/ch at 10 % THD/16 Ω matching impedance (16 Ω to 1 kΩ)
DC 2.4V (rechargeable battery × 2)
DC IN 4.5 V
(Excluding buttons and controls)
(with grip band, without batteries)
Put the grip band on your hand
Adjust the grip band to your hand size.
5
6
1
Power Supply Preparations
Basic Play
Other Play Methods
The illustration of the grip band is omitted.
Using the AC adaptor (not supplied)
Using dry-cell batteries
(not supplied)
AC power outlet
Two “R6” (LR6) alkaline batteries.
Caution:
Do not forcibly open the battery lid too wide.
AC adaptor
Battery indicator
Battery indicator
This indicator appears when the batteries are almost out of power.
Power will be cut off a short while later.
Note:
Turning off the Anti-Shock Protection EX will save the battery power
more or less. For details, see “Anti-shock Protection EX” on page 4.
Notes:
• Even if the unit is turned off, small power is consumed as long
as the AC adaptor is connected to the AC power outlet.
• When you want to purchase the AC adaptor, see page 5.
Preventing Accidental Operation (Hold mode)
This function causes the unit to ignore, accidental button presses.
Hold mode prevents the following:
• Powering on the unit accidentally (which can cause the batteries to go dead).
• Play being cut off unexpectedly.
To use the Hold mode
HOLD
OFF
• To prevent the unit from powering on accidentally, set the
HOLD switch to the ON position while the unit is turned off.
• To prevent the unit from unexpected operation during play,
set the HOLD switch to the ON position after you starts playing the disc.
ON
• When the unit is in Hold mode, “HoLd” and “ ” lights as
follows.
Power on : “ ” stays lit.
Power off : “HoLd” and “ ” lights up for a few seconds
Note:
If the HOLD switch is set to the ON position, you cannot turn on
the unit.
when 6 is pressed.
The illustration of the grip band is omitted.
Follow the steps in the numerical order.
3
HOLD
OFF
ON
4
VOLUME
6
VOLUME
Operation
To pause
To stop
To turn off the
unit
Fast forward/
reverse
During play,
During play,
While stopped,
Skip function
During play,
Reverse
Search function
Keep depressed during play.
RL
Button
Press again to restart play.
Forward
Firmly connect
1
2
Display/reference
00 81
07
Total number of tracks
44 84
10
Total playing time
No indication.
• To skip back to the previous track, quickly press 4
twice.
• During Program play, the button is used to fast forward or back through the programmed sequence of
tracks.
• During Random play, the skip button cannot be used
to skip back to tracks that were played previously in
the random sequence.
Track number in play
02 35
01
5
Elapsed playing time of
each track
• Play stops automatically
when all the tracks have
been played.
Label side
For your reference:
“dISC”
This indication appears if 3/8 is pressed when no disc is loaded
or if the disc is not properly seated.
“– –”
Preparation period before playing the track
Flashes for several seconds after pressing 3/8 to play.
“OPEn”
This indication appears when the lid is open.
Removing discs
Turn off the unit and, after the disc has stopped rotating, remove
the disc as shown below:
Auto power off
If the unit is left in stop mode for 30 seconds, the unit turns
itself off automatically to prevent the batteries from running
down.
Disc rotation noise
The portable CD player uses a power-saving operation method
so that disc rotation noise will intermittently be emitted. But, it
is not a failure.
Intro play
You can successively play the first 10 seconds of every track.
1 While stopped,
INTRO
MODE
(Repeatedly)
2
To cancel
Press MODE repeatedly until “INTRO” goes out.
Notes:
• You can also select Intro play during playback.
In this case, Intro play will start from the next track after the
current track has finished.
• You can also select Intro play during Program play mode.
Random play
During playback,
RANDOM
MODE
(Repeatedly)
After playing all tracks, the unit stops.
To cancel
Press MODE until “RANDOM” goes out, or press 7 to stop the
disc.
Notes:
• You can also select Random play in stop mode.
• During Program play, you can not select Random play.
Program play
You can program up to 32 tracks in any desired order including
the same tracks.
1 While stopped,
PROG
01
PROGRAM
Track number to be programmed
00: Not programmed yet.
00
Program sequence
number
2 Select the desired track.
PROG
01
03
e.g. Track number 3
3
PROG
02
PROGRAM
Next program sequence number
The track is registered.
4
Repeat steps 2 and 3.
When you program exceeding 32 tracks, the program sequence number returns to “01” and will overwrite the previous setting.
00
5
• To confirm the program
While stopped, press PROGRAM repeatedly. At this time, you
can change the program, if required.
• To delete the entire program
Turn off the unit.
Repeat play
You can repeat one track or all tracks.
During playback,
MODE
(Repeatedly)
To cancel
Press MODE repeatedly until the repeat indicator goes out.
Notes:
• You can also select Repeat play during Program play.
• You can also select Repeat play while stopped.
I
ALL
Hyper-Bass Sound effect
You can enjoy powerful bass sound.
HBS
OFF 21
HBS
Anti-Shock Protection EX
This function achieves excellent performance against sound interruption caused by vibrations. You will be able to enjoy listening
to music during (not vigorous) jogging.
By utilizing the high-performance servo circuit, audio data will be
stored in the memory ahead of time (up to 45 seconds worth).
Normally, this function is in effect.
ANTI
SHOCK
As the audio data is gradually stored, the indicator changes as follows:
To cancel
A.S.P
The “ANTI SHOCK” indicator goes out.
To activate again
Press the ASP button.
Notes:
• During this operation, the disc rotates at a higher rate than usual
in order to collect extra audio data. This may cause the batteries
to run out faster and could result in a slight increase in disc rotation noise.
• This function can be switched ON and OFF during playback.
However, this may cause a slight interruption in the sound because the disc’s rotational speed changes.
ANTI SHOCK
indicator
[Fully stored]
432
WAARSCHUWING!
IN DIT APPARAAT WORDT EEN LASER GEBRUIKT. HET GEBRUIK VAN REGELAARS EN HET
MAKEN VAN AFSTELLINGEN OF BEDIENINGEN
DIE NIET IN DEZE GEBRUIKSAANWIJZING
STAAN BESCHREVEN, KAN LEIDEN TOT BLOOTSTELLING AAN GEVAARLIJKE STRALING.
MAAK HET APPARAAT NIET OPEN EN GA NIET
ZELF REPAREREN. LAAT HET ONDERHOUD
AAN ERKENDE VAKMENSEN OVER.
WAARSCHUWING:
TENEINDE HET GEVAAR VOOR BRAND OF
ELEKTRISCHE SCHOKKEN TE VERKLEINEN,
MAG DIT APPARAAT NIET WORDEN BLOOTGESTELD AAN REGEN OF VOCHT.
CAUTION:
• Do not block the ventilation opening or holes. (If the ventilation openings of holes are blocked by a newspaper or
cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems must
be considered and local rules or laws governing the disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping or
splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
PRECAUCIÓN:
• No obstruya las rendijas o los orificios de ventilación.
(Si las rendijas o los orificios de ventilación quedan tapados con
un periódico, un trozo de tela, etc., no se podrá disipar el calor).
• No ponga sobre el aparato ninguna llama al descubierto, como
velas encendidas.
• Cuando tenga que descartar las pilas, tenga en cuenta los problemas ambientales y observe estrictamente los reglamentos o las
leyes locales sobre disposición de las pilas.
• No exponga este aparato a la lluvia, humedad, goteos o
salpicaduras. Tampoco ponga recipientes conteniendo líquidos,
como floreros, encima del aparato.
VOORZICHTIG:
• Zorg dat u de ventilatieopeningen en -gaten niet afsluit.
(Als de ventilatieopeningen en -gaten worden afgesloten door
bijvoorbeeld papier of een doek, kan er hitte in het apparaat worden opgebouwd.)
• Zet geen bronnen met open vuur, zoals brandende kaarsen, op
het apparaat.
• Wees milieubewust en gooi lege batterijen niet bij het huishoudelijk afval. Lege batterijen dient u in te leveren met het KCA of
bij een innamepunt voor batterijen.
• Stel dit apparaat niet bloot aan regen, vocht, drupwater of spatwater en plaats geen enkel voorwerp waarin zich een vloeistof
bevindt, zoals een vaas, op het apparaat.
G-2
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are
no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation
when open and interlock failed or defeated. Avoid
direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL,
PLACED OUTSIDE THE UNIT.
BELANGRIJK VOOR LASERPRODUKTEN
1. KLASSE 1 LASERPRODUKT
2. VOORZICHTIG: Open de bovenste afdekking niet.
Er zijn geen door de gebruiker te repareren onderdelen in het toestel; laat onderhoud en reparatie
over aan erkend onderhoudspersoneel.
3. VOORZICHTIG: Zichtbare en onzichtbare laser-
straling indien open en interlock defect of buiten
werking gesteld. Voorkom directe blootstelling aan
de straal.
4. REPRODUCTIE VAN LABEL: WAARSCHUWINGSLABEL IN TOESTEL AANGEBRACHT.
G-3
IMPORTANTE PARA PRODUCTOS LÁSER
1. PRODUCTO LÁSER CLASE 1
2. PRECAUCIÓN: No abra la tapa superior. En el in-
terior de la unidad no hay piezas que pueda reparar el usuario; encargue el servicio a personal
técnico cualificado.
3. PRECAUCIÓN: Radiación láser visible e invisible
en caso de apertura o con interbloqueo averiado o
defectuoso. Evite la exposición directa a los haces.
4. REPRODUCCIÓN DE LA ETIQUETA: ETIQUETA
DE PRECAUCIÓN, COLOCADA EN EL INTERIOR DE LA UNIDAD.
CAUTION: Visible and invisible
laser radiation when open and
interlock failed or defeated.
AVOID DIRECT EXPOSURE TO
BEAM. (e)
ADVARSEL: Synlig og usynlig
laserstråling når maskinen er
åben eller interlocken fejle.
Undgå direkte eksponering
til stråling. (d)
VARNING: Synlig Och
osynlig laserstrålning när
den öppnas och spärren är
urkopplad. Betrakta ej
strålen. (s)
VARO: Avattaessa ja
Suojalukitus ohitettunatai
viallisena olet alttiina näkyvälle
ja näkymättömälle lasersäteilylle.
Vältä säteen kohdistumista
suoraan itseesi. (f)