VIDEO CD PLAYER
XL-MV777GD/XL-MV757TN
VCD
/
DOLBY
TV
/
SURROUND
V.EFFECT
MPX
KEY CONTROL
V.REPLACE
SLOW
RANDOM PROGRAM CANCEL B.MARK
VIDEO
INTRO HIGHLIGHT B.DIGEST B.SEARCH
REPEAT SUBTITLE
SHIFT TV/VIDEO
ON SCREEN
CD1 CD2 CD3
SELECT
1234
5678
9 10 +10
TV ch TV VOL
RM-SXLMV777U
MULTI BRAND REMOTE CONTROL
ATIME
/
STANDBY/ON
POWER
ON OFF NORMALPBC OFF
DIGITAL ECHO
MIN
MAX
PHONES
STANDBY
VOCAL
EFFECT
DOWN
MIC 1
MIN MAX
VIDEO CDPLAYER
DOLBY
SURROUND
KEY CONTROL
NORMAL
MIC 2
MIN MAX
MPX
UP
MIC 3
MIN MAX
VIDEO INTRO
SUBTITLE
1
PROGRAM
6
2
7
3
8
4
9
5
10
+10
SELECT
DESIGNED BY JVCDESIGNED BY JVC
CD
CD
CD
CD
CD
3
PLAY & EXCHANGE
BOOK DIGEST
RETURN
PREV
CD
CD
BOOKMARK
B.SEARCH
3
2
1
STILL
NEXT
INSTRUCTIONS
'
For Customer Use:
Enter below the Model No. and Serial No.
which are located either on the rear, bottom or
side of the cabinet. Retain this information for
future reference.
Model No.
Serial No.
LVT0194-001B
[U, US]
Warnings, Cautions and Others / Avisos, precauciones y otras notas /
Advertêcias, precauções e outras notas /
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
PRECAUCIÓN
Para reducir riesgos de choques eléctricos, incendio, etc.:
1. No extraiga los tornillos, los cubiertas ni la caja.
2. No exponga este aparato a la lluvia o a la humedad.
ATENÇÃO
Para reduzir riscos de choques eléctricos, incêndio, etc.:
1. Não retire parafusos nem desmonte as tampas ou o
gabinete.
2. Não exponha este aparelho à chuva nem à umidade.
Caution –– POWER switch and STANDBY/ON button!
This apparatus is provided with a POWER switch to be able to minimize power consumption for safe use. Therefore,
1. When doing initial setting, complete all the connections required, connect the mains plug into the wall outlet, and set the POWER switch
to ON. After these, it will be available to operate STANDBY/ON button and so on.
2. When not in use, set the POWER switch to OFF.
3. Disconnect the mains plug to shut the power off completely. The POWER switch and STANDBY/ON button in any position do not
disconnect the mains line.
4. The power can be remote controlled.
Precaución –– Interruptor POWER y botón STANDBY/ON !
Esta unidad dispone de un interruptor POWER que sirve para reducir al mínimo el consumo de alimentación para proporcionar mayor
seguridad operacional. Por lo tanto,
1. Al ejecutar el ajuste inicial, después de completar todas las conexiones requeridas, conectar el cable de alimentación a una toma de pared,
y activar el interruptor POWER. Entonces, será posible ejecutar operaciones tales como la conmutación del estado de alimentación.
2. Desactivar el interruptorPOWER al dejar la unidad fuera de uso.
3. Desconectar el cable de alimentación para desactivar la alimentación totalmente. Cualquier que sea la posición de ajustes del
interruptor POWER y el botón STANDBY/ON , la alimentación no es cortada completamente.
4. La alimentación puede ser controlada remotamente.
Precaução –– Interruptor POWER e botão STANDBY/ON !
Este aparelho dispõe de um interruptor POWER que possibilita reduzir ao mínimo o seu consumo de energia por medida de segurança. Assim,
1. Nos ajustes iniciais, efetue todas as conexões necessárias, ligue o plugue de alimentação à tomada e coloque o interruptor POWER em
ON. Feito isso, será possível operar o botão STANDBY/ON e as diversas funções.
2. Quando não utilizar o aparelho, coloque o interruptor POWER em OFF.
3. Remova o plugue de alimentação da tomada para desligar o aparelho completamente. O interruptor POWER e o botão STANDBY/
ON , em qualquer de suas posições, não desligam a alimentação do aparelho.
4. É possível controlar remotamente a função do interruptor POWER.
G-1
IMPORTANT FOR LASER PRODUCTS / IMPORTANTE PARA PRODUCTOS LÁSER / IMPOTANTE
PARA PRODUTOS LASER /
REPRODUCTION OF LABELS / REPRODUCCIÓN DE ETIQUETAS / REPRODUÇÃO DE ETIQUETAS
/
/
/
1 CLASSIFICATION LABEL, PLACED ON REAR ENCLO-
SURE
1 ETIQUETA DE CLASIFICACIÓN, PEGADA EN LA PARTE
POSTERIOR DE LA CAJA
1 ETIQUETA DE CLASSIFICAÇÃO LOCALIZADA NA PARTE
POSTERIOR DA CAIXA DO APARELHO.
CLASS 1
LASER PRODUCT
1. CLASS 1 LASER PRODUCT
2. DANGER: Invisible laser radiation when open and interlock
failed or defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the top cover. There are no user
serviceable parts inside the Unit; leave all servicing to qualified service personnel.
2 WARNING LABEL, PLACED INSIDE THE UNIT
2 ETIQUETA DE ADVERTENCIA, PEGADA EN EL INTE-
RIOR DE LA UNIDAD
2 ETIQUETA DE ADVERTÊNCIA LOCALIZADA NA PARTE
INTERNA DA UNIDADE.
DANGER: Invisible laser
radiation when open and
interlock failed or defeated.
AVOID DIRECT EXPOSURE
TO BEAM. (e)
ADVARSEL: Usynlig laserstråling ved åbning, når
sikkerhedsafbrydere er ude
af funktion. Undgå udsættelse for stråling (d)
VARNING: Osynlig laserstrålning när denna del är
öppnad och spärren är
urkopplad. Betrakta ej
strålen. (s)
VARO: Avattaessa ja suojalukitus ohitettaessa olet
alttiina näkymättömälle
lasersäteilylle. Älä katso
säteeseen. (f)
1. PRODUCTO LÁSER CLASE 1
2. PELIGRO: En el interior hay radiación láser invisible. Evite el
contacto directo con el haz.
3. PRECAUCIÓN: No abra la tapa superior. En el interior de la
unidad no existen piezas reparables por el usuario; deje todo
servicio técnico en manos de personal calificado.
1. PRODUTO LASER CLASSE 1
2. PERIGO: O laser emite uma rediação invisível que é perigosa,
caso o aparelho esteja aberto e a trava inoperante ou
danificada. Evite exposição direta ao feixe dos raios.
3. CUIDADO: Não abra a caixa do aparelho. Não existem
peças reparáveis pelo usuário na parte interna da unidade.
Solicite assistência técnica somente a pessoal técnico
qualificado.
G-2
English
We would like to thank you for purchasing one of our JVC products.
Before connecting this unit to the wall outlet, read the instructions
carefully to ensure that you obtain the best possible performance. If
you have any questions, consult your JVC dealer.
Table of contents
GENERAL INFORMATION ...................................................................... 1
Care and handling of compact discs ......................................................... 1
BEFORE USING FOR THE FIRST TIME ................................................. 2
Basic connections ..................................................................................... 2
Connecting the player to a TV or amplifier/receiver using the Audio
Video cable ....................................................................................... 2
Connecting the player to an amplifier/receiver equipped with the
analog discrete inputs ....................................................................... 2
Video out select ................................................................................... 2
Connecting the AV COMPU LINK cable.............................................. 3
Connecting the power cord.................................................................. 3
Installing batteries ..................................................................................... 3
Putting batteries in the remote control ................................................. 3
OVERVIEW OF CONTROLS ................................................................... 4
Front panel .......................................................................................... 4
Remote control unit ............................................................................. 5
BASIC OPERATIONS .............................................................................. 6
Now you can play a variety of discs!! ........................................................ 6
Overview of the two play modes.......................................................... 6
Triple disc tray usage .......................................................................... 6
Display window .................................................................................... 6
Preparation for playing ........................................................................ 6
Inserting/removing disc(s) ................................................................... 7
Starting to play disc(s) ......................................................................... 7
Using number keys .............................................................................. 7
Stopping play....................................................................................... 8
Pausing play ........................................................................................ 8
Skipping the track ................................................................................ 8
Manual search ..................................................................................... 8
Slow-motion playback on the remote control unit ................................ 9
Using stereo headphones.................................................................... 9
Setting TV TYPE ................................................................................. 9
Selecting the Dolby Surround mode.................................................. 10
To adjust the output balance of speakers.......................................... 10
Using the remote control......................................................................... 11
Presetting the remote control to operate your own TV ...................... 11
Using the SHIFT button on the remote control unit ........................... 11
Preset code table............................................................................... 12
VARIOUS UNIQUE FUNCTIONS........................................................... 13
Various functions to enhance your enjoyment ........................................ 13
Display of operations status .............................................................. 13
Programming the track sequence you want ...................................... 13
Canceling a programmed track ......................................................... 13
Clearing a program ............................................................................ 13
Repeating tracks................................................................................ 14
Randomly playing tracks ................................................................... 14
Playing back a track from the desired time........................................ 14
Playing a multiplex sound CD............................................................ 15
Viewing the VIDEO INTRO................................................................ 15
Programming during VIDEO INTRO.................................................. 15
Viewing the highlights ........................................................................ 16
Playback with the Bookmark function ..................................................... 17
Marking segments for later viewing with the Bookmark function ......... 17
Using the BOOK DIGEST button....................................................... 17
Using the B. SEARCH button ............................................................ 17
Canceling individual bookmarks ........................................................ 18
Canceling all bookmarks on individual discs ..................................... 18
Using a microphone ................................................................................ 19
Using a wired microphone ................................................................. 19
Adjusting music key ........................................................................... 19
Adjusting echo effect ......................................................................... 19
Vocal replace..................................................................................... 20
Vocal effect ........................................................................................ 20
OPERATION OF PLAYBACK CONTROL FUNCTION ......................... 21
Playing Video CDs and SVCDs with Playback Control function ............. 21
Video CDs and SVCDs with Playback Control function .................... 22
RESTRICTING USE OF YOUR DISCS .................................................. 23
Locking a disc with the Read-Protect function ........................................ 23
Locking a disc.................................................................................... 23
Canceling Read-Protect .................................................................... 23
Releasing the Read-Protect temporarily............................................ 23
DIGITAL AUDIO CDs ............................................................................. 24
Playing Digital Audio CDs ....................................................................... 24
Playing Digital Audio CDs.................................................................. 24
Unavailable functions for Audio CDs ................................................. 24
AV COMPU LINK REMOTE CONTROL SYSTEM ................................ 25
AV COMPU LINK remote control system ............................................... 25
Connection and setup........................................................................ 25
Operation ........................................................................................... 25
SPECIFICATIONS .................................................................................. 26
Main specifications.................................................................................. 26
TROUBLESHOOTING ........................................................................... 27
Troubleshooting ...................................................................................... 27
Page 1
GENERAL INFORMATION
Care and handling of
compact discs
English
How to handle CDs
When handling a compact disc, do not touch the surface of the disc
(reflective silver side –– the side without the label).
Since compact discs are made of plastic, they are easily damaged. If
a disc gets dirty, dusty, scratched or warped, the sound will not be
picked up correctly and, in addition, such a disc may cause the CD
player to malfunction.
Care of the label side
Do not damage the label side, stick paper to, or use any adhesive on
its surface.
Storage
Make sure that discs are kept in their cases. If discs are piled one on
top of another without their protective cases, they can be damaged. Do
not put discs in a location where they may be exposed to direct sunlight,
or in a place where the humidity or temperature is high. Avoid leaving
discs in your car!
Maintenance of discs
If there are fingerprints or dirt adhering to a disc, wipe it with a soft dry
cloth, moving from the center outwards.
If a disc is difficult to clean, wipe with a cloth moistened with water.
Never use record cleaners, petrol, alcohol or any anti-static agents.
Which compact discs can be used?
Many types of compact discs are sold for a variety of uses. The player
can play the following compact discs:
• SVCD (Super VCD) discs
*Better video resolution using MPEG2 and VBR
(Variable Bit Rate) technologies.
*Up to four languages can be included as subtitles
or song lyrics.
*Up to four languages can be included as audio.
• Video CD discs both with and without PBC
function
PlayBack
Control
• Audio CD discs
'
Discs you can't play back
Any other discs than listed above (such as CD-ROM, DVD or CD-I
discs) cannot be played. Playing back such discs may generate noise
and damage your speakers.
* Even though a logo listed above is printed on the disc, it may not be
played if it is a non-standard disc.
Using the remote control
The remote control is ready to use when its batteries are installed
properly.
To use it, point its infrared light-emitting window toward the display
window of the player and press a button. The operating range of the
remote control is up to about seven meters in front of the player and
within about 30 degrees to each side –– with nothing between the
remote control and the player interrupting the beam path.
If pressing a button on the remote control does not produce any
response, check to make sure it is pointed correctly and try again. If it
still does not function, check the batteries.
CAUTION
Sometimes during play noise or images may be garbled. This is
sometimes due to the disc. (It may not be up to industry standards.)
These symptom are caused by the discs, not by the malfunction of
the player.
Page 1
BEFORE USING FOR THE FIRST TIME
AV COMPU LINK
RIGHT LEFT
RIGHT LEFT
PAL
NTSC MULTI
VIDEO OUT
SELECT
AUDIO OUT
FRONT
AUDIO OUT
SURROUND
S-VIDEO
OUT
VIDEO OUT
AUDIO OUT
CENTER
(Red) (White)
To input FRONT
jack of the
amplifier/receiver
To input REAR
jack of the
amplifier/receiver
To input CENTER jack of
the amplifier/receiver
Audio cable (optional)
Audio cable
(optional)
(Red)
(White)
Basic connections
The Video CD player must be connected directly to a television set or,
an amplifier or receiver that is connected to a television or monitor.
Select a level, dry location free of dust and vibration, having a
temperature maintained between 5 and 35°C (41 and 95°F).
Connecting the player to a TV or amplifier/receiver using the Audio Video cable
First make the audio and video connections before connecting the AC
power cord. Also, make sure that the equipment (television, amplifier
or receiver) to be connected with the player is turned off.
Firmly insert the yellow pin plug of the Audio Video cable in the yellow
VIDEO OUT jack on the rear panel of the player; the red pin plug in the
red AUDIO OUT FRONT (RIGHT) jack; and the white pin plug in the
white AUDIO OUT FRONT (LEFT) jack. (The RIGHT and LEFT output
jacks are for the right and left audio channels.)
Then firmly insert the pin plugs at the other end of the Audio Video cable
into the matching video and audio INPUT jacks.
If your television set has an S-video input, we recommend you to
connect it with S-VIDEO OUT of the player using the optional S-Video
cable, in addition to the (standard) video connection, to get a better
picture quality.
To input audio jack of
the television/amplifier/
(Red) (White)
receiver
Audio Video cable (supplied)
Connecting the player to an amplifier/
receiver equipped with the analog discrete inputs
Connect the player’s 5-channel outputs (AUDIO OUT FRONT-RIGHT/
LEFT, AUDIO OUT SURROUND-RIGHT/LEFT, and AUDIO OUT
CENTER) to the analog discrete inputs of an amplifier/receiver using
audio cables, while the VIDEO OUT to the television’s video input
terminal using the yellow plugs of the supplied Audio Video cable. Be
sure to connect correctly between corresponding terminals.
AUDIO OUT
AUDIO OUT
SURROUND
VIDEO OUT
Page 2
FRONT
S-VIDEO
OUT
RIGHT LEFT
RIGHT LEFT
VIDEO OUT
SELECT
NTSC MULTI
PAL
AUDIO OUT
(Yellow)
CENTER
AV COMPU LINK
Audio Video cable (supplied)
To input video jack of
the television/amplifier/receiver
To input S-Video jack of
the television/amplifier/receiver
S-Video cable (optional)
Video out select
Set the VIDEO OUT SELECT switch on the rear panel to NTSC, PAL,
or MULTI mode according to your television system.
NTSC .................... for NTSC exclusive TV
PAL ....................... for PAL exclusive TV
MULTI ................... for Multisystem TV
AUDIO OUT
RIGHT LEFT
FRONT
AUDIO OUT
RIGHT LEFT
SURROUND
VIDEO OUT
SELECT
NTSC MULTI
PAL
AUDIO OUT
CENTER
AV COMPU LINK
VIDEO OUT
S-VIDEO
OUT
Note
• Set the switch before turning the power on. If you change the switch
position while the power is on, the new setting does not become
effective until you turn the power to standby and then on.
BEFORE USING FOR THE FIRST TIME
Installing batteries
English
Connecting the AV COMPU LINK cable
Connect with other JVC equipment supporting the AV Compulink by
using the supplied AV COMPU LINK cable to facilitate operations.
See “AV COMPU LINK remote control system” on page 25.
AUDIO OUT
RIGHT LEFT
FRONT
AUDIO OUT
RIGHT LEFT
SURROUND
VIDEO OUT
S-VIDEO
OUT
AUDIO OUT
CENTER
VIDEO OUT
SELECT
NTSC MULTI
PAL
AV COMPU LINK cable
AV COMPU LINK
To AV COMPU LINK jack
of another JVC equipment
Connecting the power cord
IMPORTANT
Check the setting of the VOLTAGE SELECTOR switch on the rear
panel of the player.
Change the setting if the switch is not set for the main voltage
supplied to your home.
Putting batteries in the remote control
The battery compartment is located on the back of the remote control.
1. Insert your finger in the recess under the battery compartment
cover, and pull off the cover.
2. Place the two accessory R6P (SUM-3)/AA (15F) batteries in
the remote control according to the polarity markings (“+” and
“–”) inside the compartment and on the batteries.
After the audio-video connectors had been connected, insert the
female end of the power cord firmly into the AC POWER CORD
socket loceted on the rear panel of the player. Then insert the male
end of the power cord into the wall outlet.
When the power is connected and the POWER ON/OFF button is
depressed (ON), the STANDBY indicator on the left-hand side of
the player’s front panel comes on. See “Overview of Controls” for
a description of the controls on the player.
220V-240V
115V-127V
VOLTAGE SELECTOR
AC power cord
Wall outlet
Ó AC IN
3. Insert the two tabs of the cover in their respective slots, and
snap the cover in place.
The batteries last about one year with normal use. If function of the
remote control become erratic, replace the batteries.
Precautions for the safe use of batteries
Observe the following precautions for the safe use of batteries. Their
life will be shortened, they may burst or their contents may leak if they
are used improperly.
Page 3
OVERVIEW OF CONTROLS
3
2
K
A
The following is an explanation of the basic function of controls on the
front panel of the player and the remote control. The function of some
controls may be restricted in actual use depending on the
VIDEO CD PLAYER
3 4 5
VOCAL
EFFECT
DOWN
MIC 1
MIN MAX
SURROUND
KEY CONTROL
8
MIN MAX
10
12
DOLBY
NORMAL
MIC 2
1
6
/
STANDBY/ON
POWER
ON OFF NORMAL PBC OFF
DIGITAL ECHO
9
MIN
MAX
PHONES
11
STANDBY
2
7
Left front panel of the player
(Controls marked (R) have equivalents on the remote control.)
/
1
(STANDBY/ON) button (R)
Turns the player on or to STANDBY.
2
STANDBY indicator (Red)
Lights when the POWER ON/OFF button is depressed and the
player is in standby mode.
3
VOCAL EFFECT button (R) with indicator (Green)
Selects the vocal effect mode for the microphone inputs (1 through
3). Pressing this button cycles the modes as shown below.
HARMONY → CHORUS → FLANGE → OFF
4
DOLBY SURROUND button (R) with indicator (Green)
Selects the Dolby surround mode. See page 10.
5
MPX button (R) with indicator (Green)
Selects the audio channel(s) of a disc to be monitored. See
“Playing a multiplex sound CD” on page 15.
6
POWER ON/OFF button
Turns the power to standby or completely off.
7
PLAY MODE switch
Switches between the NORMAL and PBC modes. It only affects
Video CD and SVCD discs with PBC function.
NORMAL: Allows use of the Playback Control (PBC) function.
PBC OFF: Inhibits the PBC function.
8
KEY CONTROL buttons (R) with indicator (Green)
Transposes the music key.
DOWN button: used to flatten by a half tone.
NORMAL button: returns to original key.
UP # button: used to sharpen by a half tone.
9
DIGITAL ECHO knob
Adjusts the degree of the echo effect for the microphone (1 through
3) voice.
10
MIC 1 to MIC 3 knobs
Adjusts volume of the microphone corresponding to MIC number.
11
PHONE jack
Used for connecting stereo headphones. The volume is set to a
predetermined level and is not adjustable.
12
MIC jacks (1 through 3)
Used for connecting microphones (1 through 3). The jacks correspond to MIC 1 to 3 volume knobs located above.
on-going operations. The remote control has fourteen unique function buttons in addition to those on the player.
MPX
UP
MIC 3
MIN MAX
CD
CD
CD
VIDEO INTRO
14
SUBTITLE
15
13
Center front panel of the player
CD1 to CD3 trays
13
Used to load discs. To insert/remove discs, press the 0 (OPEN/
CLOSE) button located at the right of the tray corresponding to disc
number.
14
VIDEO INTRO button (R)
Applies to Video CD and SVCD discs only. The introductory
several seconds of tracks on a disc are displayed on the television
screen in order to present the contents of the disc.
SUBTITLE button (R)
15
Effective only when playing back an SVCD disc. SVCD discs may
have up to four subtitles which you can select to see on the TV
screen (as an optional feature). Pressing this button cycles the
subtitles as shown below.
Subtitle 1 → Subtitle 2 → Subtitle 3 → Subtitle 4 → OFF
Display window
16
Shows information about the status of operation.
BOOK DIGEST button (R)
17
Displays video segments you marked with the Bookmark function.
See page 17.
Right front panel of the player
0 (OPEN/CLOSE) buttons (CD number 1 to 3)
18
Used to open and close disc trays 1 to 3 respectively. When, after
opening the CD1 tray, another 0 (OPEN/CLOSE) button is pressed,
the CD1 tray is first closed, then the other CD tray selected is
opened.
CD1 through CD3 buttons (R) with indicators (Green)
19
Plays the disc of the number indicated on the button. As soon as
the disc begins playing, the indicator blinks.
RETURN button (R)
20
Utilized for operation with the PBC function. This button is used to
return to a menu screen during play.
8 (PAUSE)/STILL button (R)
21
Temporarily suspends playing. Video motion freezes and audio
reproduction stops. Pressing the button repeatedly advances the
picture frame-by-frame. (Video CD and SVCD only)
22
BOOKMARK button (R) with indicator (Green)
Places a “bookmark” at video segments you want to find later for
almost instant replay. See page 17.
23
B. SEARCH button (R) with indicator (Green)
Retrieves video segments which you marked with a bookmark.
See page 17.
CD
3
PLAY & EXCHANGE
BOOK DIGEST
1716
Page 4
The controls with identical names on the player and on the remote
control have the same function and are used in the same manner.
18 19
CD
3
CD
2
CD
1
RETURN
20 21
BOOKMARK
B.SEARCH
PREV
4 / ¢ PREV / NEXT buttons (R)
24
During operation with the Playback Control function
Invokes previous or next screen.
During operation without the Playback Control function
Used to skip track(s) forward or backward from the current track
being played, or to shift the playing location backward or forward
quickly.
25
Jog/Shuttle dial
Used to play forward or backward quickly.
Number keys (1 to 10) (R)
26
Used to specify a track number for playing or programming.
To select a number between 1 and 10, press the corresponding
key for the number. To select a number higher than 10, use the +10
key. The maximum number you can specify is 99.
See “Using number keys” on page 7 for the examples.
These keys are also used to select a menu item number. See also
“Operation of Playback Control function” on page 21.
27
PROGRAM button (R)
Any desired sequence of tracks can be programmed with the
number keys and the +10 button. (On the remote control use +10)
The program button cannot be used while the Playback Control
function is activated.
+10 button (R)
28
Used when specifying a number which is higher than 11. See
“26Number keys” above and “Operation of Playback Control
function” on page 21.
7 (STOP) button (R)
29
Stops play.
3 (PLAY)/SELECT button (R)
30
Starts to play the disc.
Remote control unit
31
VCD / /TV / button
Turns the player on and to STANDBY.
When pressed after you hold down the SHIFT button, turns the TV
on or off.
32
V.REPLACE button
Activates the vocal replace function, inserting your voice in place
of the disc vocals.
33
ON SCREEN button
Controls whether or not control and operation status are displayed
on the television screen or monitor.
OVERVIEW OF CONTROLS
English
VCD
TV
ON SCREEN
ATIME
/
/
31
33
35
37
39
43
44
DOLBY
SURROUND
V.EFFECT
MPX
KEY CONTROL
32
1
2
3
4
STILL
22
23
25
NEXT
24
5
PROGRAM
29 30
6
7
8
26
9
10
27 28
+10
SELECT
DESIGNED BY JVC
34
36
38
40
41
42
34
SLOW button
V.REPLACE
CD1 CD2 CD3
SLOW
RANDOM PROGRAM CANCEL B.MARK
VIDEO
INTRO HIGHLIGHT B.DIGEST B.SEARCH
SELECT
1234
5678
9 10 +10
REPEAT SUBTITLE
SHIFT TV/VIDEO
TV ch TV VOL
RM-SXLMV777U
MULTI BRAND REMOTE CONTROL
Starts slow-motion playback.
1 / ¡ MANUAL SEARCH button
35
Shifts the playing location backward and forward quickly. Holding
down the button causes it to go much faster.
36
RANDOM button
Changes the disc track program to a random sequence from disc
1 through 3 respectively.
37
CANCEL button
Cancels the latest track you have programmed. The latest programmed track is canceled whenever you press this button. Also
used to cancel a bookmark.
38
HIGHLIGHT button
Applies to a video CD and SVCD discs to see highlights of a track.
Displays the several seconds seconds of each of nine equal-time
segments of the track.
39
ATIME button
Used to play back a disc track from the desired time. See page 14.
REPEAT button
40
Repeats a track or inserted discs from 1 to 3.
41
SHIFT button
Used together with other keys for various functions. See page 11.
TV/VIDEO button
42
Sets the input mode of the TV. Also used to preset the remote
control unit, to control some functions on your TV set. See page 11.
43
TV ch – / TV ch + keys
Changes the television channel.
44
TV VOL + / TV VOL – keys
Turns the TV volume up or down.
Page 5
BASIC OPERATIONS
Now you can play a
variety of discs!!
Overview of the two play modes
The player has two play modes for Video CD and SVCD discs. These
are selected by the PLAY MODE switch on the left side of the front
panel.
NORMAL PBC OFF
NORMAL: Allows use of the Playback Control (PBC) function.
PBC OFF: Inhibits the PBC function.
It only affects Video CD and SVCD discs with PBC function.
Triple disc tray usage
Up to three discs can be loaded in the player. You may insert a disc into
any of the disc trays 1 through 3.
If you want to play only a specified disc, press the corresponding CD
1, 2 or 3 button located to the right of the 0 (OPEN/CLOSE) button.
When three discs are inserted, basic order of playing is as follows.
• Pressing CD 1: CD 1 → CD 2 → CD 3 → STOP
• Pressing CD 2: CD 2 → CD 3 → CD 1 → STOP
• Pressing CD 3: CD 3 → CD 1 → CD 2 → STOP
CD
CD
CD
CD
CD
3
PLAY & EXCHANGE
3
CD
2
CD
1
Display window
The display window indicates many aspects of control and operation
status.
1 52 3
1
Shows the disc number being played.
2
Shows mainly the total number of tracks and the track number being
4
played.
3
Mainly shows the cumulative time (minutes and seconds) of the
track when the player is playing. It also shows the total time of the
disc for about ten seconds after the player stops playback, or
finishes reading the disc information when a disc has been inserted.
4
Shows the type of disc being played.
5
Each indicator in this area lights when the corresponding function
is activated.
Preparation for playing
Turn on the television set, amplifier or receiver to which the player
is connected. Then set the channel and modes properly to accept
the player’s output signal.
CAUTION
Set the sound volume of the television set, amplifier or receiver
to which the player is connected to a reasonable level before
starting playback.
Page 6
Press the POWER ON/OFF button.
POWER
ON OFF
Press the / button on the front panel or the VCD / (TV /) button
on remote control. The STANDBY indicator goes out.
VCD
/
TV
/
/
or
STANDBY /ON
(Remote control)
The display window shows the initial information as shown below.
BASIC OPERATIONS
1234
5678
9 10 +10
English
Inserting/removing disc(s)
Press the 0 (OPEN/CLOSE) button (1 through 3) to open the disc
tray. Then place the disc in the round recess of the tray with label
side up. To close the tray, press the 0 (OPEN/CLOSE) button
again.
If you press the 0 (OPEN/CLOSE) button of the disc which is playing,
the player stops and then opens the tray.
If you press the 0 (OPEN/CLOSE) button of a disc that is not being
played, you can change discs without stopping play.
CD
3
CD
2
CD
1
Note
• When loading a disc in the disc tray, be sure to position the disc
inside the recess. Otherwise, the disc will be damaged when the
disc tray is closed, and the disc cannot be removed from the unit.
CD
If the PBC function is activated, the display window shows "Pb"
and the menu is displayed on the television screen. See page 21
for the "operation of PBC function".
If the PBC function is not activated, the player starts playback from the
first track of the disc.
• For individual track selection, use the number keys (see the
explanation below) or the 4 / ¢ buttons.
• During playback, the display window shows the disc number and
the track number being played.
• When you press 3 button during play, the disc will restart from the
beginning of the track.
Using number keys
If the PBC function is not activated, you can select a track number
by using the numeric keys.
On the player .................... 1 to 10 and +10 key
Example: For number 5, press 5. For number 15, press +10, then 5.
For number 20, press +10, then 10. For number 32, press +10 three
times, then 2.
1
2
3
4
5
6
7
8
9
10
Tray
CORRECT
Starting to play disc(s)
Press the 3 (PLAY)/SELECT button. The player starts to play
from the disc indicated in the display window.
Or, press one of the CD 1 through 3 buttons to start to play the
corresponding disc.
SELECT
+10
INCORRECT
On the remote control ..... 1 to 10 and +10 key
Select numbers as described above.
Note
or
• When you select the track using the number keys, the track will start
playing without pressing 3 (PLAY)/SELECT button.
(Remote control)
CD
3
CD
2
CD
1
CD1 CD2 CD3
or
(Remote control)
Page 7
BASIC OPERATIONS
Stopping play
Press the 7 (STOP) button to stop play at any time.
or
(Remote control)
Pausing play
Press the 8 (PAUSE)/STILL button to temporarily suspend play.
STILL
or
(Remote control)
Notes
• When the 8 (PAUSE)/STILL button is pressed once, “PAUSE”
appears on the television screen, the video motion freezes and the
sound is turned off. The still picture advances frame-by-frame each
time the 8 (PAUSE)/STILL button is pressed. This frame-by-frame
function is available only for Video CDs and SVCDs.
• To release the pause, press the 3 (PLAY)/SELECT or blinking CD
1 through 3 button.
• During “PAUSE” the time counter on the display will blink.
Manual search
During play, you can search the disc position by using the shuttle
dial, or 4 / ¢ buttons on the player or 4 / ¢ buttons on the
remote control unit.
Rotating the shuttle dial to the right causes the disc to play
forward quickly. Rotating it to the left causes it to play backward
quickly.
BOOKMARK
B.SEARCH
Holding down the 4 / ¢ buttons on the player or the 1 / ¡
buttons on the remote control unit causes the disc to play forward
or backward quickly.
Continuing to hold down the buttons causes it to search much
faster.
(Remote control)
2-1
B 3 3 – – – E M.SEARCH
1:30
Skipping the track
If the PBC function is not activated, you can skip track(s) by using
the 4 / ¢ buttons during play.
Pressing the 4 button skips the current track backward, while
pressing ¢ skips forward.
PREV NEXT
or
(Remote control)
(Television screen)
Notes
• In some circumstances, this function is not available when the PBC
function is activated.
• The angle at which you hold the shuttle dial determines the manual
search speed.
Page 8
BASIC OPERATIONS
English
Slow-motion playback on the remote
control unit
Press the SLOW button to play in slow-motion. By pressing the
SLOW button consecutively, the playback speeds are cycled as
shown below.
SLOW
(Remote control)
1/4 1/8 1/16 Normal
Note
• This function can only be used when playing a video CD or SVCD.
Using stereo headphones
Connecting stereo headphones
Connect stereo headphones to the PHONES jack at the lower-left of
the front panel. The volume level is fixed and cannot be adjusted.
PHONES
Setting TV TYPE
To playback SVCD discs which are recorded for wide-screen televisions correctly, select the TV TYPE to match your television.
Operation
1. While the player is in stop mode, press and hold the
RETURN button until the following display appears on the
television screen.
RETURN
2. If your television is a normal television, press the 3 (PLAY)/
SELECT button of the player to select NORMAL.
If your television is a wide-screen television, press the 7
(STOP) button of the player to select WIDE.
The following display appears.
TV TYPE
PLAY. OK
STOP.
CANCEL
TV TYPE
PLAY. NORMAL
STOP.
WIDE
3. Press the 3 (PLAY)/SELECT button to complete the setting.
Pressing the 7 (STOP) button returns to the previous display
for selection.
Notes
• The TV TYPE setting is effective for SVCD discs recorded for widescreen television.
• The initial setting is NORMAL.
• Once the TV TYPE is set and memorized, it does not disappear by
turning the player to standby mode or completely off.
Page 9
BASIC OPERATIONS
Front-left
(L CH)
Center
(C CH)
Front-right
(R CH)
Rear
(S CH)
Selecting the Dolby Surround mode
You can enjoy the surround sound with discs bearing the mark
Preparation
• If your system is ready for the Dolby Pro Logic, make the connection
between the player and your amplifier/receiver correctly according
to “Basic connections” on page 2.
• Even if your audio system is for a normal stereo reproduction,
including a stereo amplifier/receiver and two speakers, you can
enjoy the pseudo-surround sound with 3D Phonic mode.
Operation
To select the Dolby Surround mode, use the DOLBY SURROUND
button. Pressing this button cycles the modes as shown below.
NORMAL
(Pro Logic)
OFF 3D Phonic 3 STEREO
When any mode but OFF is selected, the DOLBY SURROUND
button lights.
Select the mode depending on your system configuration.
NORMAL (Pro Logic):
Select this mode when the center speaker cannot reproduce the
bass better than the front speakers. The bass portions of the
center channel signals are output through the front speakers.
WIDE (Pro Logic):
Select this mode when the center speaker can reproduce the
bass better than the front speakers. All signals of the center
channel are output through the center speaker.
PHANTOM (Pro Logic):
Select this mode when you do not use a center speaker. The
center speaker channel signals are output through the front
speakers.
3 STEREO:
Select this mode when a center speaker is connected without
rear speakers.
.
WIDE
(Pro Logic)
PHANTOM
(Pro Logic)
To adjust the output balance of speakers
1. Set the Dolby Surround mode to any one of NORMAL, WIDE,
PHANTOM and 3 STEREO.
2. In stop mode, press the SUBTITLE button on the player
repeatedly until the following display apears on the television
screen.
PROGRAMMED SONGS
CENTER / SURROUND CH
LEVEL ADJUSTMENT
TEST TONE
CENTER
SURROND
(Television screen)
L
CH
CH
0
CH
0
The test tone is output from speakers in the following order.
See whether you hear the test tone from each speaker in the
same level at the listening position.
3. If any adjustment is necessary, press the DOLBY SURROUND
button to select the channel (CENTER or SURROUND) to be
adjusted.
The selected channel turns yellow.
4. Each press of the UP ( # ) button on the player or remote control
unit increases the output level up to +10 dB.
Each press of the DOWN ( ) button on the player or remote
control unit decreases the output level up to -10 dB.
5. Pressing the SUBTITLE button on the player or remote control
unit completes the adjustment.
The setting is memorized and will not disappear even if the player turns
to the standby mode or completely off.
When setting the Dolby Surround mode to PHANTOM, CENTER
cannot be adjusted.
When setting the Dolby Surround mode to 3 STEREO, SURROUND
cannot be adjusted.
The channel from which the
test tone is output
Output level
3D Phonic:
Select this mode when reproducing the surround sound with
only two front speakers. It gives you very realistic surround
effect as if the sound is reproduced through the Dolby Surround decoder.
This mode is the result of research on sound localization
technology carried out at JVC for many years and make it
possible to reproduce the surround sound with only two front
speakers.
* Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic",
and the double-D symbol are trademarks of Dolby Laboratories.
Page 10
Using the remote control
BASIC OPERATIONS
English
Presetting the remote control to operate
your own TV
You can use the player’s remote control unit to control some functions
on your TV set (e.g., turning the TV on and off, adjusting volume, or
selecting channels). First, though, you must preset the remote control
to make it compatible with your TV.
Operation
1. Check the Preset Code Table (page 12) to determine the twodigit brand code number for your TV.
2. While holding down the TV/VIDEO button on the remote control, press the number keys to insert the two-digit brand code
number. (For example, if the code number is "28", press the
number key 2, then 8. If the first digit is a "0", press 10. Thus,
if the code number is "09", press the number key 10, then 9. If
the code number is "10", press the number key 1, then 10. If
it is "20", press the number key 2, then 10.)
Notes
• Before the remote control unit leaves the factory, the brand code
number is set as No. 01 (JVC).
• Depending on your television set’s age and other factors, brand
code numbers may be different from those shown in the table. In
such a case, try out other codes until you find one that corresponds
to your television.
3. While still holding down the TV/VIDEO button, press the 7
(STOP) button on the remote control.
TV/VIDEO
+
Using the SHIFT button on the remote
control unit
You can control other functions with the remote control, simply by
pressing a button while holding down the SHIFT button. Some of these
functions are useful for Karaoke and Video CD playing, others for
controlling the TV.
7 SHIFT button functions to control the TV
SHIFT + VCD / ⇒ Turns the TV on and off
SHIFT + A TIME ⇒ TV MUTE (Mute the TV sound)
SHIFT + 1 ⇒ TV Channel 1
SHIFT + 2 ⇒ TV Channel 2
•
•
•
SHIFT + 10 ⇒ TV Channel 0*
SHIFT + REPEAT ⇒ 1 - (The first digit of a TV Channel number 10
to 19. Push a number key to insert the second digit.)*
SHIFT + SUBTITLE ⇒ 2 - (The first digit of a TV Channel number
20 to 29. Push a number key to insert the second digit.)*
SHIFT + +10 ⇒ -/- - (To change a one - digit or to change a two digit TV channel number, using a number key.)*
SHIFT
4. The TV is turned off if the code number is correct. Repeat the
procedure from the beginning if you weren’t successful the
first time.
SHIFT + B. SEARCH ⇒ ENTER (Push after choosing a channel.
This function registers the channel you have chosen.)*
Note
• The asterisk * indicates that these operations do not work for some
manufacturers’ television sets.
Page 11
BASIC OPERATIONS
Preset code table
No.
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Television manufacturer
JVC
PANASONIC
SONY
SHARP
TOSHIBA/BEIJING/CHANGHONG
MITSUBISHI/CHANGHONG
HITACHI
SANYO
FUNAI
AIWA
DAEWOO
SAMSUNG
LG (GOLDSTAR)
THOMSON
FERGUSON
16
17
18
19
20
21
22
23
24
25
26
27
28
Page 12
PHILIPS/TCL/CHANGHONG
GRUNDIG
ITT
MIVER
FINLUX
NOKIA
NEC
JINXING/PEONY1
PEONY2
PEONY3/CHANGHONG
KONKA
PEIJIN/NOBLEX
TCL
VARIOUS UNIQUE FUNCTIONS
Various functions to
enhance your enjoyment
English
Display of operations status
Preparation
This function is controlled by the remote control.
Operation
Press the ON SCREEN button on the remote control. By pressing
the ON SCREEN button, the following information may be easily
and quickly displayed or removed from the television screen.
Time, Echo effect, Key control, Program, Repeat, Random, Multiplexing, Vocal effect, DOLBY SURROUND, Vocal replace, Bookmark, etc.
PROGRAMMED SONGS
2-1 1:30
ON SCREEN
(Remote control)
(Television screen)
Programming the track sequence you want
Preparation
It is not possible to enter programming mode during play. If playing,
stop the player with the 7 (STOP) button.
Operation
1. Press the PROGRAM button to enter the programming mode.
PROGRAM is displayed in the display window.
PROGRAM
or
PROGRAM
To stop the program playback, press the 7 (STOP) button. Pressing the 3 (PLAY)/SELECT button again causes the player to start
playing from the next programmed track.
or
(Remote control)
Canceling a programmed track
Operation
There are two canceling functions (canceling the last programmed
track and canceling the current track).
• To cancel the last programmed track, press the CANCEL
button on the remote control and the last programmed track
will be canceled. This can be done both in playback and stop
modes.
PROGRAMMED SONGS
2-1 3-1
2-2 1-1
2-3 1-2
2-4 1-3
2-5
(Television screen)
• To cancel the current track (during playback):
* press the 7 (STOP) button to stop playback. The next press
of the 3 (PLAY)/SELECT button will start playback from the
next programmed track.
* press the ¢ button to skip to the next programmed track.
The number located lowest is the
last track programmed.
(Remote control)
2. Specify the disc by a CD (1-3) button and then the track by the
number keys. You can program up to nine tracks by repeating
this procedure.
3. To play the programmed tracks press the 3 (PLAY)/SELECT
button.
Notes
• The track number playing, next track programmed, and number of
programmed tracks are displayed from the left-top of the television
screen. You may use the ON SCREEN button to delete this
information.
• Once the programmed track is played, it is deleted from the
program.
• You may also program additional tracks during the program playback as long as the number of the programmed tracks does not
exceed nine.
Note
• To verify the tracks you programmed, stop the player and see ON
SCREEN information.
Clearing a program
To delete all programmed tracks you have entered, press the 7
(STOP) button and then the PROGRAM button while the player is
in stop mode. “PROG OFF” will be displayed on the television
screen.
PROGRAM
or
PROGRAM
(Remote control)
Page 13
VARIOUS UNIQUE FUNCTIONS
Repeating tracks
It is possible to repeat playback of all discs or only a single track.
Preparation
This function is controlled by the remote control.
Operation
By pressing the REPEAT button on the Remote Control, REPEAT
modes are cycled as shown below.
REPEAT
(Remote control) (Display window)
REPEAT ALL
(All discs)
REPEAT1
(1 track)
(Television screen)
Notes
• When playing a programmed sequence of tracks, only one track
repeat is available.
• The Repeat function is not available when a Video CD or SVCD disc
with PBC is inserted and the PLAY MODE switch is set to NORMAL.
• Only REPEAT ALL is available when the player is in RANDOM
mode.
• You cannot repeat the segment between bookmarks.
→ All discs
→ Current track
REPEAT OFF
To cancel the random playback, press the RANDOM button again
after stopping the player.
RANDOM
(Remote control)
Note
• Random is not effective in program mode.
Playing back a track from the desired time
You can play back a disc track from the desired time.
Operation
While playing back the desired track, operate the following
procedures.
1. Press the ATIME button on the remote control.
ATIME
(Remote control)
2. Enter the desired time by pressing the corresponding number
keys from left to right digits.
“10” button is used for “0” entry.
Randomly playing tracks
Preparations
• This function is controlled by the remote control.
• This function plays tracks randomly from one disc.
• This function is available while the player is in stop mode.
Operation
Press the RANDOM button and random playing will start.
RANDOM
(Remote control)
To stop the random playback, press the 7 (STOP) button.
or
(Display window)
(Remote control)
1
2
3
4
5
10
+10
6
7
8
9
or
1234
5678
9 10 +10
(Remote control)
3. Press the 3 (PLAY)/SELECT button.
SELECT
or
(Remote control)
The disc will start playback from the specified time.
For example, if you want to play back the disc from “05m06s”,
press the following buttons.
ATIME → 5 → 10 → 6 → 3
Note
• Some discs may not be played back from the specified time
precisely.
Page 14
VARIOUS UNIQUE FUNCTIONS
English
Playing a multiplex sound CD
This function is used for multiplex sound discs.
See manuals attached to discs for detail information.
Operation
By pressing the MPX button consecutively, channel multiplexing
modes are cycled as shown below.
MPX
or
NORMAL
(left-channel/
right-channel)
L-CH MONO R-CH MONO
(Television screen)
When L-CH MONO or R-CH MONO is selected, the MPX button on
the player lights and the display indicates MPX L or MPX R
respectively.
* When playing back an SVCD;
STEREO 1 STEREO 2 MONO 1
MONO 4 MONO 3 MONO 2
(Television screen)
When any of MONO 1 through 4 is selected, the MPX button lights.
MPX
(Remote control)
Viewing the VIDEO INTRO
Preparation
When you play a Video CD or SVCD with the Playback Control
function, the PLAY MODE switch should be set to PBC OFF.
Operation
1. Play the disc you want to see a digest of.
2. Press the VIDEO INTRO button on the player or the remote
control just after starting disc play. Then, the player starts to
display in sequence the first several seconds and track numbers of all tracks on the disc.
VIDEO INTRO
or
3. To select a track during the video intro mode, press the
number key corresponding to the item number on the television screen.
VIDEO INTRO
123
456
789
(Television screen)
Note
• The Video intro function is not available in the Random mode.
VIDEO
INTRO
(Remote control)
Note
• Note that you can hear no audible sound at the STEREO 2, MONO
3 and MONO 4 positions if no audio is recorded on STEREO 2.
Programming during VIDEO INTRO
Operation
1. Stop play.
2. Press the PROGRAM button so that PROGRAM is lit in the
display.
3. Press the disc button you want to play, and enter 1 on the
number keys.
4. Press the 3 (PLAY)/SELECT button and then, after the disc
has started to play, press the VIDEO INTRO button.
5. The player starts to display in sequence the first several
seconds and track numbers of all tracks on the disc. Select the
numbers you want to program. You can program nine tracks.
6. Press the 3 (PLAY)/SELECT button to play.
Page 15
VARIOUS UNIQUE FUNCTIONS
Viewing the highlights
This function is used for a movie Video CD or SVCD.
Preparations
• When you play a Video CD or SVCD with the Playback Control
function, the PLAY MODE switch should be set to PBC OFF.
• This function is controlled by the remote control unit.
Operation
1. Start playing the track you want to see the highlights of.
2. After the track begins to play, press the HIGHLIGHT button on
the remote control.
HIGHLIGHT
(Remote control)
HIGHLIGHT
123
456
789
(Television screen)
3. To select one of the nine segments, press the number key (1
to 9) of the segment which you want to play.
The segment will start from several seconds before the shown
time below each segment.
Notes
• The segments are each of nine equal-time divisions of the track.
• Nine different highlights are displayed for one minute.
• If no number key is pressed for a minute after the Highlight view
appears on the screen, the screen is replaced with the Highlight
view of the next track.
• While in VIDEO INTRO or HIGHLIGHT, sometimes the image is
partially distorted. This symptom is caused by noise in the disc itself
or incorrect manufacturing, not by a malfunction of the player.
Page 16
Playback with the
Bookmark function
VARIOUS UNIQUE FUNCTIONS
English
Marking segments for later viewing with
the Bookmark function
The Bookmark function lets you mark segments of a Video CD or
SVCD, so that you can have almost instant playback of desired scenes
later. You can mark segments on up to ten discs, with a maximum of
nine segments per disc.
Even if you take the disc out of the player, its bookmarks will stay stored
for later use, until you erase them.
Operation
While playing the disc, press the BOOKMARK button at the
segments you want to mark for later playing. Bookmark numbers
appear on the television screen and the BOOKMARK indicator on
the player flashes.
BOOKMARK
B.SEARCH
or
Notes
• The Bookmark function works only with Video CDs and SVCD.
• The Bookmark function is most easily used when the player is in
PBC OFF mode.
• When you begin marking segments in either NORMAL or PBC OFF
mode, all subsequent markings and searches for that disc must be
done in the same mode.
B.MARK
(Remote control)
Using the B. SEARCH button
7 With PBC off
1. Press the B. SEARCH button. The B. SEARCH light will flash
on and off, indicating the player is in the Bookmark Search
mode.
BOOKMARK
B.SEARCH
or
2. Press the number key (1 to 9) which corresponds to the
number of the segment where you want to start play. While
playing the disc, you can also use the 4 or ¢ button to
select the desired bookmark number.
Note
• To exit the Bookmark Search mode and return to regular viewing,
press the B. SEARCH button again.
7 With PBC on
1. Press the B.SEARCH button to enter Bookmark Search mode.
If you press the button while playing, the player will stop and
then enter Bookmark Search mode.
BOOKMARK
B.SEARCH
or
B.SEARCH
(Remote control)
B.SEARCH
Using the BOOK DIGEST button
1. Press the BOOK DIGEST button while playing the disc.
BOOK DIGEST
or
2. The marked segments will be highlighted on the screen, with
their respective numbers (maximum of nine).
3. Press the number key (1 to 9) which corresponds to the
number of the segment where you want to start play.
1
2
3
4
5
6
7
8
9
10
+10
Note
• The Bookmark Digest function is not available in PBC function.
B.DIGEST
(Remote control)
(Remote control)
2. Press the number key (1 to 9) which corresponds to the
number of the segment where you want to start play.
Note
• The Bookmark Search function ends automatically, and the player
returns to regular viewing.
Page 17
VARIOUS UNIQUE FUNCTIONS
Canceling individual bookmarks
7 Canceling bookmarks set in PBC OFF mode
[Method A]
1. In PBC OFF mode, start playing the segment whose bookmark
you want to cancel.
2. Press the CANCEL button on the remote control unit. The
bookmark for the segment immediately preceding the part you
are playing will be canceled.
CANCEL
(Remote control)
Note
• When you cancel a bookmak number, all subsequent bookmark
numbers change, moving up one level to fill the gap you made.
[Method B]
1. Start playing in NORMAL mode.
2. Press the CANCEL button on the remote control unit. The
bookmark with the highest number will be canceled (regardless of the playing position).
CANCEL
(Remote control)
Canceling all bookmarks on individual
discs
7 Canceling bookmarks on a disc in the player
You can cancel bookmarks on the currently selected disc in the
player using the 8 (PAUSE)/STILL button on the player.
In stop mode, press the 8 (PAUSE)/STILL button on the player
until bookmark information on the television screen stops
blinking.
STILL
7 Canceling bookmarks on a disc which was played the earliest
You can cancel bookmarks on a disc you played the earliest
whether it is in the player or not.
In stop mode, press the 7 (STOP) button on the player until
bookmark information on the television screen stops blinking.
PROGRAMMED SONGS
(Television screen)
DISC: 1
BOOKMARK
CANCEL
The total number of
discs with bookmarks
7 Canceling bookmarks set in NORMAL mode
1. Start playing in either NORMAL or PBC OFF mode.
2. Press the CANCEL button on the remote control unit. The
bookmark with the highest number will be canceled (regardless of the playing position).
CANCEL
(Remote control)
PROGRAMMED SONGS
(Television screen)
DISC: 3
BOOKMARK
CANCEL
The total number of
discs with bookmarks
Note
• You can also cancel all bookmark information by setting the
POWER button to OFF.
Page 18
Using a microphone
VARIOUS UNIQUE FUNCTIONS
English
Using a wired microphone
Operation
Up to three microphones can be connected to the MIC jacks on the front
panel.
MIC 1
MIN MAX
1. Turn on the microphone switch.
2. Turn the MIC 1, MIC 2, and MIC 3 knobs clockwise (level up) or
counterclockwise (level down) as desired.
MIN MAX
MIC 1
MIC 2
MIC 3
MIN MAX
MIC 2
MIC 3
Adjusting music key
Press the KEY CONTROL buttons ( or #) to change the key in
which the music plays. To return the music to its original key,
press the NORMAL button.
You can also adjust the music using the remote control unit.
DOWN NORMAL
KEY CONTROL
UP
KEY CONTROL
or
(Remote control)
Notes
• The degree the key has been raised or lowered is displayed on the
television screen.
• When the song ends, the key control will return to NORMAL mode
automatically.
Adjusting echo effect
You can add echo to your voice.
Turn the DIGITAL ECHO knob clockwise (level up) or counterclockwise (level down) to adjust the echo effect as desired.
DIGITAL ECHO
MIN MAX
MIN MAX
MIN MAX
ATTENTION
When you are not using the microphone, set the MIC switch to OFF.
Be sure to remove the microphone
Note when connecting the sound output to the input of a TV or VCR:
If an excessively strong signal is given to a unit through a microphone, for example when using Karaoke, it may cause an adverse
effect such as distorted sound. Lower the sound volume using the
microphone control.
Karaoke etiquette
Think of your neighbors when you are enjoying karaoke music.
Particularly late at night, the sound you enjoy may reach your
neighbors more than you expect. Common sense and courtesy are
always appreciated.
MIN MAX
Page 19
VARIOUS UNIQUE FUNCTIONS
Vocal replace
Preparation
This function is used for multiplex sound discs.
Operation
1. Press the V.REPLACE button during play or stop. REPLACE
will appear on the display window and VO.REPLACE will
appear on the television screen. When you start singing, the
disc vocal is removed and your voice is inserted into the
music.
V.REPLACE
(Remote control)
2. To cancel voice replacement, press the V.REPLACE button
again.
Note
• You cannot use the Vocal replace function with a disc that has
vocals recorded on the left channel.
Vocal effect
By pressing the VOCAL EFFECT button, you can apply a vocal effect
to the microphone input signals. Three effect modes are available;
HARMONY, CHORUS and FLANGE. The selected mode is shown on
the television screen, while the VOCAL EFFECT button on the player
lights when any of the effect modes is selected.
VOCAL
EFFECT
or
V. EFFECT
(Remote control)
Page 20
OPERATION OF PLAYBACK CONTROL FUNCTION
Playing Video CDs and
SVCDs with Playback
Control function
English
This player provides a Playback Control function which utilizes a
procedure (menu selection) programmed in a Video CD or SVCD. The
playback operation procedure may differ depending on the disc you
use.
The Playback Control function provides:
• High-resolution still image display - Super-fine reproduction of still
images with more than four times the resolution of video tape.
• Menu-driven playback - interactive menus for easy selection of
tracks.
Preparations
• A Video CD or SVCD with the Playback Control function is required
for this operation.
• The PLAY MODE switch must be set to NORMAL.
• The buttons used for operating the PBC function are the number
keys, the 4 / ¢ PREV/NEXT buttons, 3 (PLAY)/SELECT button, and RETURN button.
Button functions
Number keys ............................ Select a specific menu item from the
(Including +10 button) television screen or monitor.
4 / ¢ PREV/NEXT buttons .... Move through menu etc.
3 (PLAY)/SELECT button ....... When “3” or “SELECT” is displayed
on the television screen, pressing
this button jumps to the specific picture.
RETURN button ................ Returns to the menu.
7 (STOP) button ...................... Stops operations.
Operation
1. Verify that the PLAY MODE switch is set to NORMAL.
2. Press the CD (1 through 3) or 3 (PLAY)/SELECT button. The
player starts up the PBC function. “Pb” is shown in the display
window. The main menu is displayed on the television screen.
CD3
CD2
CD1
3. To move through the disc menus, press the 4 / ¢ PREV/
NEXT button.
PREV NEXT
or
2-PBC PBC
1
2
3
4
(Television screen)
or
SELECT
4. When the disc menu you want appears, select an item in the
menu by using the number keys. The numbers on the number
keys correspond to the menu item numbers.
5. To return to a menu press, the RETURN button.
RETURN
Notes
• Page numbers in the disc menu show that preceding pages exist.
To move from the current menu, press the 4 / ¢ PREV/NEXT
button.
• If you have no desire to use the PBC function when playing a disc
with the PBC function, switch the PLAY MODE switch to "PBC OFF"
before playing.
• If you switch the mode from NORMAL to PBC OFF while playing
back a PBC disc, playback will stop. Operate the procedure above
again from the beginning.
• If you press the number keys directly to select the track before
playing, you cannot enter PBC mode regardless of the PLAY
MODE switch setting.
Page 21
OPERATION OF PLAYBACK CONTROL FUNCTION
Video CDs and SVCDs with Playback
Control function
What is Playback Control function?
The Playback Control function, allows you to enjoy menu-driven
operation and high-resolution still images which have a resolution four
times greater than moving pictures.
Example of playback using the Playback Control function
1
2
3
12
Moving
picture
1
2
3
213
Moving
picture
Moving
picture
1
Moving
picture
1
2
2
picture
A selection menu is displayed when you start playing a Video CD and
SVCD disc with the Playback Control feature. The selection menu
shows a list of numbers for selection. Some discs may show moving
pictures or a divided screen.
1. When a list of numbers is displayed, selecting a number shows its
contents.
2. When “3” or “SELECT” is displayed on the television screen,
pressing this button jumps to the specific picture.
• Menu-driven playback
• High-resolution still image display
Menu screen
To next screen
Still
To previous screen
3. When the selection menu is redisplayed after you have played
4. After playback, press RETURN to go back to the previous
Note
• When a menu is displayed for a long time (about ten minutes), the
You can interact with the screen using a menu display to select and
play an entry.
You can display high-quality images four times clearer than moving
pictures.
3
Moving
Press
RETURN.
picture
Press
Still
picture
Moving
picture
Moving
picture
RETURN.
Press
RETURN.
your selection, selecting a number again replays its contents.
(Some discs may show the menu screen several times.)
When and are shown, pressing “NEXT” or “PREV” can
change the selection menu.
screen.
To stop playback, press 7 (STOP).
screen background automatically fades out to prevent screen
burn-in while the setting is suspended.
Page 22
RESTRICTING USE OF YOUR DISCS
CD
3
CD
2
CD
1
Locking a disc with the
Read-Protect function
English
Locking a disc
The Read-Protect function restricts viewing of a disc. Only people who
know the code can unlock the disc. You can lock only Video CDs and
SVCDs (up to ten discs).
Notes
• You cannot lock a disc while it is playing.
• All Read-Protect operations are performed using buttons on the
player, not on the remote control.
Operation
1. Play the disc for a moment, then press the 7 (STOP) button.
2. Hold down the NEXT button on the player for at least three
seconds. The track and time numbers are no longer displayed.
NEXT
3. Press the number key “8” four times. The display window
indicates “Loc.”
Now the disc cannot be viewed. You can open and close the tray and
you can turn the player power on and off, but no other functions are
available for this locked disc.
Canceling Read-Protect
Operation
1. Place the disc in a tray, then press the CD button (1 - 3) for that
tray. PROTECT is displayed on the television screen.
2. Hold down the 4 PREV (Previous) button on the player for
more than three seconds. The indication “Loc” in the display
window will flicker for a moment.
PREV
3. Press the number key “8” four times. You can now play the
disc.
1
2
3
4
5
6
7
8
9
10
+10
Note
• PROTECT is displayed on the television screen.
Cut out the following instructions and keep them separately, to
ensure privacy.
Releasing the Read-Protect temporarily
Operation
1. As above, hold down the 4 PREV (Previous) button on the
player for at least three seconds. The indication “Loc” in the
display window will flicker for a moment.
PREV
2. Press the number key “7” four times. You can now play the
disc temporarily until you press the 0 (OPEN/CLOSE) button
for that disc, or until you play another disc. Turning off the
player does not restore the Read Protect function.
Page 23
DIGITAL AUDIO CDs
Playing Digital Audio CDs
Playing Digital Audio CDs
Basically, the operations for Video CDs and SVCDs apply to the Audio
CDs except for some video-related functions.
Notes
• The display has no indicator to show disc type.
• The PLAY MODE switch is ineffective for Audio CDs.
Unavailable functions for Audio CDs
The following functions for Video CD and SVCD discs are not available
with Audio CDs.
• Slow-motion playback
• Frame-by-frame function
• Video intro function
• Highlight function
• Bookmark function
Page 24
AV COMPU LINK REMOTE CONTROL SYSTEM
Receiver Video CD player
TV
AV COMPU LINK remote
control system
English
When you are going to enjoy a disc, you usually have to turn on your
television, receiver and Video CD player and setup these components’
individually. If, however, the system consists of components which
support JVC’s AV COMPU LINK remote control system, instead of
individual setup, simply pressing the 3 (PLAY)/SELECT button allows
you to enjoy the disc.
Connection and setup
Using the AV COMPU LINK cable, connect the AV COMPU LINK
terminals of each component to one another.
After the connection is done, make the player’s AV COMPU LINK
setting by the following procedures.
1. While the player is in the STANDBY mode, hold down the 7
(STOP) button and press the / (STANDBY/ON) button.
The corresponding CD button (CD1 to CD3) of the selected AV
COMPU LINK setting blinks.
2. To change the selection, press the 3 (PLAY)/SELECT button.
Each press of the button cycles the selection as shown below.
CD 1 CD 2 CD 3
3. To exit the setting mode, press the 7 (STOP) button to return
to the STANDBY mode, or press the / (STANDBY/ON) button
to enter the ON mode.
To AV COMPU LINK (II or EX)
If you connect the Video CD player to a television and VCR via AV
COMPU LINK as illustrated above, set the VCR’s Remote Control
Code and Video CD player’s AV COMPU LINK setting as follows.
• When connecting with VIDEO 1 input terminal of the television:
Video CD player’s AV COMPU LINK setting: CD 2
VCR’s Remote Control Code: B
• When connecting with VIDEO 2 input terminal of the television:
Video CD player’s AV COMPU LINK setting: CD 3
VCR’s Remote Control Code: A
If you connect the Video CD player to a television and receiver via AV
COMPU LINK as illustrated above, set the Video CD player’s AV
COMPU LINK setting to CD1.
Operation
You can enjoy pictures and/or sound by just putting the Video CD
player into play mode. You do not have to operate the TV and/or
receiver including power switching.
Preparation
Set the POWER switch of each component to ON.
1. Insert a disc into the Video CD player.
TV
Video CD player
If you connect the Video CD player to a television via AV COMPU LINK
as illustrated above, set the Video CD player’s AV COMPU LINK
setting as follows.
• When connecting with VIDEO 1 input terminal of the television:
CD 2
• When connecting with VIDEO 2 input terminal of the television:
CD 3
TV
To AV COMPU LINK
(II or EX)
Video CD player Video cassette recorder
To AV COMPU LINK
2. Press 3 (PLAY)/SELECT of the Video CD player.
SELECT
The following actions are performed automatically:
• Turning on the power of each component.
• Setting the source of the television to the external input which the
Video CD player is connected to.
• Setting the source of the receiver to the Video CD player.
Notes for connection
• Connect the AUDIO OUT jacks of the Video CD player to the audio
input jacks of a receiver which show “DVD”. Otherwise, the system
will not work correctly.
• There may be no description about connections to a Video CD player
in the instruction manual of a television or VCR. But a television or
VCR with AV COMPU LINK terminals which show II can be connected to a Video CD player.
Page 25
SPECIFICATIONS
Main specifications
XL-MV777GD/XL-MV757TN
Model Video CD player
Playback disc Super VCD
Video CD
Digital Audio CD
Front panel XL-MV777GD Gold
color XL-MV757TN Titanium
Total harmonic
distortion
S/N ratio 90 dB
Frequency
response
Input terminal Microphone 5 mV (5.0 kΩ)
Output Line output 2.0 Vrms (full scale)
terminal
Echoing Digital echoing
Power AC 115-127/220-240 V 50/60 Hz
requirements Selectable with the voltage selector
Power 16 watts
consumption In standby mode 6 watts
Weight 5.3 kg (11.7 lbs)
Dimensions 435 x 126.5 x 325.3 mm
(W/H/D) 17-3/16 x 5 x12-13/16 inches
0.01% (1 kHz)
20 Hz – 20 kHz
Video output (composite) 1.0 Vp-p (75Ω)
S video output
Y: Illuminance 1.0 Vp-p (75Ω)
C: Chrominance. burst 0.286 Vp-p (75Ω)
Accessories
AC power cord ........................................................................... 1
Audio video cable....................................................................... 1
Remote control unit (RM-SXLMV777U)..................................... 1
Batteries (R6P(SUM-3)/AA(15F)) ......................................... 2
AC plug adaptor (except People's Republic of China) ............... 1
AV COMPU LINK cable ............................................................. 1
Page 26
TROUBLESHOOTING
Troubleshooting
What appears to be a malfunction may not always be so. Please go through the following list before requesting service.
English
Symptom
Power does not come on.
Remote control does not work.
No image is displayed on the
monitor.
Playback does not start.
Speaker does not produce
sound.
Sound is distorted or noise is
generated.
Image is garbled.
Possible cause
Power plug is disconnected from AC outlet.
The POWER button is in the OFF position.
Batteries are exhausted.
The tip of the remote control unit is not pointed at the
receiving part of the player.
The video cable is not connected.
The TV is not set in video mode.
An incompatible disc is loaded.
No disc is loaded.
Disc is loaded upside down.
Audio cable is not connected.
Operation of the external amplifier is incorrect.
Disc is dirty.
Connection is wrong.
Remedy
Firmly connect the plug to AC outlet.
Depress the POWER button.
Replace the batteries with new ones.
Use the remote control correctly.
Firmly connect the cable.
Set the TV in video mode.
Load a disc compatible with the player.
Load a disc.
Reload the disc with the label up.
Firmly connect the cable.
Operate the amplifier correctly.
Wipe the disc surface with a soft cloth.
Correctly connect cables. See page 2.
Sound is intermittent.
Image is garbled.
Disc tray does not come out
when 0 (OPEN/CLOSE) button
is pressed.
Operation is not possible.
The AV COMPU LINK system
does not work correctly.
The malfunction may be caused by a device other than the player. Check other devices connected to the player.
Disk is dirty.
Disc is scratched.
Disc is warped.
Power plug is disconnected from the power outlet.
Microcomputer malfunctions due to lightning or static
electricity.
The player's AV COMPU LINK setting is not correct.
Wipe the disc surface with a soft cloth.
See page 1.
Replace the disc with a new one.
Firmly insert the plug into the outlet.
Turn the power off, then on again.
Make the setting correctly.
Page 27
AC Power Line Instructions (not applicable for Europe, U.S.A., Canada,
Australia and U.K.)
220V-240V
AUDIO OUT
FRONT
AUDIO OUT
SURROUND
VIDEO OUT
S-VIDEO
OUT
RIGHT LEFT
RIGHT LEFT
VIDEO OUT
SELECT
NTSC MULTI
AUDIO OUT
CENTER
AV COMPU LINK
PAL
115V-127V
VOLTAGE SELECTOR
Ó AC IN
IMPORTANT
BEFORE PLUGGING IN, check that your AC power line
voltage corresponds with the position of the voltage
selector switch provided on the outside of this equipment.
If different, reset the voltage selector switch, to prevent
damage or risk of fire/electric shock.
EN, CH
VICTOR COMPANY OF JAPAN, LIMITED
0299TTMUBNJEM
JVC
Loading...