Consists of CA-UXQ3S and SP-UXQ1S
由 CA-UXQ3S 和 SP-UXQ1S 组成
UX-Q3W
Consists of CA-UXQ3W and SP-UXQ1W
由 CA-UXQ3W 和 SP-UXQ1W 组成
UX-Q3A
Consists of CA-UXQ3A and SP-UXQ1A
由 CA-UXQ3A 和 SP-UXQ1A 组成
UX-Q3B
Consists of CA-UXQ3B and SP-UXQ1B
由 CA-UXQ3B 和 SP-UXQ1B 组成
For hiding the demonstration
display, refer to page 9.
有关隐藏演示显示的详情,请参阅
第 9 页。
INSTRUCTIONS
使用说明书
LVT1218-003A
[UF]
Introduction
Warnings, Cautions and Others
/
警告,注意及其他须知事项
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
CAUTION — F button!
Disconnect the mains plug to shut the power off
completely.
The F button in any position does not disconnect the
mains line.
The power can be remote controlled.
CAUTION
• Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to
get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws governing
the disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
IMPORTANT FOR LASER PRODUCTS / 镭射产品的重要说明
注意
为了减少触电、火灾等危险:
1. 请勿擅自卸下螺丝钉、盖子或机壳。
2. 请勿让本机受雨淋或置于潮湿环境中。
注意- F 开关!
想要完全关闭电源,须将电源插头从插座上拔下。
无论 F 键处于何种位置,主电路仍旧没有关闭。
电源开关可用遥控器进行控制。
注意
• 切勿堵塞通风口或通风孔。
(如果通风口或通风孔被报纸或布等物堵塞,热量将无
法散出。)
• 切勿在本系统上放置明火,如点燃的蜡烛。
• 想要丢弃电池时,务必考虑环保问题以及严格遵守当地
关于处理废旧电池相关的法律规定和条例。
• 切勿让本机受雨淋、受潮湿、落上或溅上水滴,亦勿在
本机上面放置盛满液体的容器,如花瓶。
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no
user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation when
open and interlock failed or defeated. Avoid direct
exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL,
PLACED INSIDE THE UNIT.
To avoid risk of electric shock and fire and to protect from
damage, locate the apparatus as follows:
Top/Front/Back/Sides:No obstructions should be placed in
Bottom:Place on the level surface. Maintain
In addition, maintain the best possible air circulation.
Front view
前视图
15cm
the areas shown by the dimensions
below.
adequate air path for ventilation by
placing on a stand with a height of
10 cm or more.