JVC UX-D427S Instruction Manual

Page 1
Instruction Manual
Wireless DAB Hi-Fi with Valve Amp technology
UX-D427S
Page 2
Page 3
Contents
Safety Warnings ...................................................................................................................5
Unpacking .............................................................................................................................7
Product Overview ................................................................................................................8
Main Unit .........................................................................................................................................................8
Remote Control ............................................................................................................................................ 9
Battery Replacement for the Remote Control ............................................................................... 10
Remote Control Operation Range .......................................................................................................11
Connections ........................................................................................................................12
Connecting the DAB/FM Aerial .............................................................................................................12
Speaker Connections ...............................................................................................................................12
COAXIAL / OPTICAL Connection ..........................................................................................................13
Connecting Auxiliary Equipment ........................................................................................................13
Using Headphones ....................................................................................................................................13
Connecting to the Mains Supply .........................................................................................................14
Basic Operating ..................................................................................................................15
Switching ON / OFF ...................................................................................................................................15
Selecting Modes .........................................................................................................................................15
Adjust the Speaker Level Settings and Eects ...............................................................................15
Adjusting the Display Brightness ........................................................................................................ 16
Clock Operation .................................................................................................................17
Manually Setting the Clock ....................................................................................................................17
Time Display ................................................................................................................................................17
Clock Synchronization .............................................................................................................................17
Sleep Timer ..................................................................................................................................................17
Daily Timer................................................................................................................................................... 18
To Deactivate or Re-activate a Daily Timer ..................................................................................... 18
DAB Radio Operation.........................................................................................................18
Auto Scan ......................................................................................................................................................19
Manual Tuning ............................................................................................................................................19
Secondary Services ...................................................................................................................................19
Presetting Stations ....................................................................................................................................19
Recalling a Preset Station .......................................................................................................................19
DAB Information Display ........................................................................................................................ 20
FM Radio Operation ...........................................................................................................21
Tuning in a Station .................................................................................................................................... 21
Presetting Stations ................................................................................................................................... 21
RDS (Radio Data System) Reception .................................................................................................. 22
CD/MP3 Operation ............................................................................................................ 23
Compatible Disc Types ........................................................................................................................... 23
Playback ........................................................................................................................................................23
To Skip Search or Search and Play ...................................................................................................... 23
Selecting an Album (for MP3 disc) ..................................................................................................... 23
Repeat Playback ........................................................................................................................................ 24
Text Display During Playback ............................................................................................................... 24
Programme Play ........................................................................................................................................ 24
Page 4
Using the USB .................................................................................................................... 25
AUX / OPTICAL / COAXIAL Operation .............................................................................. 25
Bluetooth® Operation ....................................................................................................... 26
Maintenance .......................................................................................................................27
Cleaning the Unit ...................................................................................................................................... 27
Removing, Installation the Grill and Cleaning the Speakers .................................................... 27
Handling Discs ........................................................................................................................................... 27
Cleaning Discs ............................................................................................................................................ 27
Storing Discs ............................................................................................................................................... 28
Hints and Tips .................................................................................................................... 28
Product Fiche and Specifications .................................................................................... 30
Useful Information and Licences ......................................................................................31
Page 5
Safety Warnings
• Read all the instructions carefully before using the unit and keep them for future reference.
• Retain the manual. If you pass the unit onto a third party make sure to include this manual.
• Check that the voltage marked on the rating label matches your mains voltage.
Damage
• Please inspect the unit for damage after unpacking.
• Do not continue to operate the unit if you are in any doubt about it working normally, or if it is damaged in any way - switch o, withdraw the mains plug and consult your dealer.
Location of Unit
• The unit must be placed on a at stable surface and should not be subjected to vibrations.
• Do not place the unit on sloped or unstable surfaces as the unit may fall o or tip over.
• The mains socket must be located near the unit and should be easily accessible.
• This unit is designed for indoor, domestic use only.
Temperature
• Avoid extreme degrees of temperature, either hot or cold. Place the unit well away from heat sources such as radiators or gas / electric res.
• Avoid exposure to direct sunlight and other sources of heat.
Naked Flames
• Never place any type of candle or naked ame on the top of or near the unit.
Moisture
• To reduce the risk of re, electric shock or product damage, do not expose this unit to rain, moisture, dripping or splashing. No objects lled with liquids, such as vases, should be placed on the unit. Do not operate the unit with wet hands, near water or other liquid.
• If you spill any liquid into the unit, it can cause serious damage. Switch it o at the mains immediately. Withdraw the mains plug and consult your dealer.
Ventilation
• To prevent the risk of electric shock or re hazard due to overheating, ensure that curtains and other materials do not obstruct the ventilation vents.
• A minimum distance of 5 cm around the unit should be maintained to allow for sucient ventilation.
• Do not install or place this unit in a bookcase, built-in cabinet or in another conned space. Ensure the unit is well ventilated.
Safety
• Always disconnect the unit from the mains supply before connecting / disconnecting other devices or moving the unit.
• Unplug the unit from the mains socket during a lightning storm.
• In the interests of safety and to avoid unnecessary energy consumption, never leave the unit switched on while unattended for long periods of time, e.g. overnight, while on holiday or while out of the house. Switch it o and disconnect the mains plug from the mains socket.
Mains Cable
• Make sure the unit or unit stand is not resting on top of the mains cable, as the weight of the unit may damage the mains cable and create a safety hazard.
• If the mains cable is damaged it must be replaced by the manufacturer, its service agent, or similarly qualied persons in order to avoid a hazard.
The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
Interference
• Do not place the unit on or near appliances which may cause electromagnetic interference. If you do, it may adversely aect the operating performance of the unit, and cause a distorted picture or sound.
Batteries
• Batteries used in the remote control for this unit are easily swallowed by young children and this is dangerous.
• Keep loose batteries away from young children and make sure that the battery holder tray is secure in the remote control. Seek medical advice if you believe a cell has been swallowed.
5
Page 6
• Please dispose of batteries correctly by following the guidance in this manual.
• Do not expose the battery to direct sunlight or sources of excessive heat.
• Attention should be drawn to the environmental aspects of battery disposal.
Supervision
• Children should be supervised to ensure that they do not play with the unit and the remote control.
• Never let anyone especially children push anything into the holes, slots or any other openings in the case - this could result in a fatal electric shock.
Class 1 Laser Product
• This unit utilises a laser. Use of controls, adjustments or performance of procedures other than those specied herein may result in hazardous radiation exposure.
• Before moving the unit, ensure the disc tray is empty.
• Always remove the disc when the unit is not in use.
• Failure to do so will risk severely damaging the disc and the unit.
• Do not stack devices, heat from other devices may aect the performance of the unit.
CLASS 1
LASER PRODUCT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning ash with arrowhead
symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the unit’s enclosure that may be of sucient magnitude to constitute a risk of electric shock.
The exclamation point within an
equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the manual accompanying the unit.
Service
• To reduce the risk of electric shock, do not remove screws. The unit does not contain any user-serviceable parts. Please leave all maintenance work to qualied personnel.
• Do not open any xed covers as this may expose dangerous voltages.
Maintenance
• Ensure to unplug the unit from the mains socket before cleaning.
• Do not use any type of abrasive pad or abrasive cleaning solutions as these may damage the unit’s surface.
To prevent the spread of re, keep candles or other open ames away from this product at all times.
• This equipment is a Class II or double
insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth.
~ AC voltage: This symbol indicates that the rated voltage marked with the symbol is AC voltage.
DC voltage: This symbol indicates that the rated voltage marked with the symbol is DC voltage.
6
Page 7
Thank you for purchasing your new product.
We recommend that you spend some time reading this instruction manual in order that you fully understand all the operational features it oers. You will also nd some hints and tips to help you resolve any issues.
Read all the safety instructions carefully before use and keep this instruction manual for future reference.
Unpacking
Remove all items from the packaging. Retain the packaging. If you dispose of it please do so according to local regulations.
The following items are included:
Speakers x 2Main Unit
RCA to 3.5 mm Stereo Audio CableSpeaker Cable x 2
Mains Cable
• If items are missing, or damaged please contact Partmaster (UK only). Tel: 0344 800 3456 for assistance.
• If you require additional assistance:
For UK, please call our UK Call Centre on 0344 561 1234. For Ireland, please call our Ireland Call Center on 1 890 818 575.
Instruction Manual
Remote Control / AAA Batteries x 2
DAB / FM Aerial
Quick Start Guide
Quick Start Guide
7
Page 8
Product Overview
Main Unit
Front View
1 2 3 4 5 6
7 8 9 10
Rear View
11 12 13 14 15 16
1. STANDBY Button
2. Power Indicator
3. Remote Sensor
4. Disc Tray
5. LCD Display
6.
Open / Close Button
7. SOURCE Button
8. USB (5V 1A) Socket
9. REP/SHUF Button
10.
Button
11.
Play/Pause Button
12.
Button
13. – VOLUME + Dial
14. – BASS + Dial
15. – TREBLE + Dial
16. Headphones Socket
1817 19 20 21
8
22
17. OPTICAL Socket
18. COAXIAL Socket
19. DAB/FM Aerial Socket
20. AUX IN L/R Sockets
21. SPEAKER OUT L/R Sockets
22. AC~ Socket
Page 9
Remote Control
1. Standby Button
2.
Open / Close Button
3. SOURCE (CD/USB/AUX/BT/ OPTICAL/COAXIAL/FM/DAB) Buttons
4. INTRO/SCAN Button
5. SHUFFLE/REPEAT Button
6. CLOCK Button
7. SLEEP/TIMER Button
8. BASS +/– Buttons
9. TREB +/– Buttons
10. INFO Button
11. EQ Button
12. ALBUM/PRESET Button
13. ENTER Button
14. Button
15. Button
16. ALBUM/PRESET Button
17. / CLEAR Button
18. Button
19. / PAIR Button
20. Button
21. / Buttons
22. VOL +/– Buttons
23. Number (0-9) Pad
24. DIMMER Button
25. PROG Button
1
3
4 5
8
10 12
14
16 17
21
23
24
2
6 7 9
11
13
15
18 19
20 22
25
9
Page 10
Preparation
Battery Replacement for the Remote Control
1. Press and slide the back cover to open the battery compartment of the remote control.
2. Insert two AAA size batteries (included). Make sure the (+) and (–) ends of the batteries match the (+) and (–) ends indicated in the battery compartment.
3. Close the battery compartment cover.
10
Handling the Battery
• Improper or incorrect use of batteries may cause corrosion or battery leakage, which could cause re, personal injury or damage to property.
• Only use the battery type indicated in this manual.
• Do not install new batteries with used ones and do not mix dierent types of batteries.
• Do not dispose of used batteries as domestic waste. Dispose of them in accordance with local
regulations.
• Do not expose the batteries to excessive heat such as sunshine, re or the like.
Handling the Remote Control
• Do not drop the remote control.
• Do not allow anything to impact the remote control.
• Do not spill water or any liquid on the remote control.
• Do not place the remote control on a wet object.
• Do not place the remote control under direct sunlight or near sources of excessive heat.
• Remove the battery from the remote control when not in use for a long period of time, as corrosion or
battery leakage may occur and result in physical injury, and / or property damage, and / or re.
• When the battery is exhausted, the remote control will not function.
Page 11
Remote Control Operation Range
• The remote control sensor on
Remote sensor
the front unit is sensitive to the remote control’s commands up to a maximum of 6 metres away and within a maximum of a 60° arc.
• Please note that the operating distance may vary depending on the brightness of the room.
30° 30°
Max. 6 m
• Make sure that there is no obstacle between the infrared remote sensor of the unit and remote control. If you install the unit on rack, etc., the remote controllable range may decrease depending on the thickness or colour of glass door of rack.
• Do not expose the infrared remote sensor to direct sunlight or other strong light, such as inverter uorescent light.
11
Page 12
Connections
Connecting the DAB/FM Aerial
Fully extend the DAB / FM aerial. Connect the supplied DAB / FM aerial to the DAB / FM antenna socket on the rear of the unit by turning the antenna screw cap clockwise.
Rear View of the Main Unit
• Do not overtighten, this could damage the aerial.
• To avoid noise, keep aerial away from the unit, the
connecting cables and the mains cable.
Speaker Connections
1. Connect the speaker cables between the terminals as shown below.
2. Connect the red/black speaker cables to the red terminal heads (+) and silver speaker cables to the black terminal heads (-).
Rear View of the Speaker
Rear View of the Main Unit
Rear View of the Speaker
How to Connect
• For the main unit, turn the terminal cap counterclockwise to loosen it.
• Insert the wire into the terminal fully.
• Turn the terminal cap clockwise to securely connect it.
• For the speaker terminals, press and hold down the terminals while inserting the wires.
Release the terminal cap when the wires are inserted.
Connecting the speaker cable to the wrong terminal will cause the sound to go out of phase.
12
Page 13
COAXIAL / OPTICAL Connection
Use an optical cable (not included) or coaxial cable (not included) to connect the main unit’s OPTICAL / COAXIAL socket to the OPTICAL OUT / COAXIAL OUT socket of the external device.
Rear View of the Main Unit
External Device
Coaxial cable (not included)
Optical cable (not included)
Connecting Auxiliary Equipment
Connect the AUX terminals on the rear of the main unit to the AUX output socket on the mobile device with an RCA to 3.5 mm stereo audio cable illustrated below.
Rear View of the Main Unit
Mobile Device
RCA to 3.5 mm stereo audio
cable (included)
Using Headphones
Turn down the volume before connecting headphones (not included). Slowly raise the volume with the headphones on until you reach your desired volume. When headphones are connected, the speakers automatically mute.
Front View of the Main Unit
Headphones (not included)
Long-term exposure to loud music may cause hearing damage. It is best to avoid extreme volume when using headphones, especially for extended periods.
The EQ settings (including BASS and TREBLE) are not available when you are using headphones. It is not a defect.
13
Page 14
Connecting to the Mains Supply
• Ensure all audio connections of the unit are connected before connecting to the mains power socket.
• Make sure the mains plug is rmly inserted into the mains socket.
• To switch the unit o completely, remove the mains plug from the mains socket.
• Please turn the unit o completely to save energy when not in use.
• Use the mains cable as the disconnect device. The disconnect device shall remain readily operable.
Unwind the mains adapter cable to its full length. Connect the AC socket at the rear of the main unit to mains plug to the mains socket.
Rear View of the Main Unit
To the mains socket
14
Page 15
This instruction manual explains the basic instructions for operating this unit. Unless otherwise stated, all operations described are based on remote control use.
Basic Operating
Switching ON / OFF
When you rst connect the unit to the AC power, the unit will be in Standby mode. The Power indicator will light up red.
• Press on the unit or the remote control to switch the unit on. The system will switch to the last selected source and the sound level will x on level 6 if the previous sound level is lower than 6, or the sound level will x on level 16 if the previous sound level is higher than 16.
• Press on the unit or the remote control to switch the unit back to standby mode and the Power indicator will light up red.
• To switch the unit o completely, remove the mains plug from the mains socket.
• Please turn the unit o completely to save energy when not in use.
• The unit automatically turns to Standby mode after 15 minutes if the unit is idle
in CD, USB, BT (Bluetooth®), COAXIAL, OPTICAL or AUX mode.
• The unit will save memory of the last selected sound level from 6-16. For any level selected outside this range, the unit will then x on the default level of either 6 or 16.
Selecting Modes
Press the SOURCE button on the unit or the corresponding mode buttons on the remote control to switch between CD, USB, BT (Bluetooth®), COAXIAL, OPTICAL, FM, DAB or AUX modes. The selected mode will show on the display.
Adjust the Speaker Level Settings and Eects
Adjusting the Volume
To increase or decrease the volume, turn the – VOLUME + dial on the unit or press the VOL + / buttons on the remote control.
Mute Sound
If you wish to turn the sound o, press button on the remote control. Press button again, or press VOL + / – to resume normal listening.
15
Page 16
Alternatively, you can directly press the following buttons on the remote control to switch to your desired mode:
• CD to switch to CD mode.
• USB to switch to USB mode.
• AUX to switch to AUX mode.
• BT to switch to Bluetooth® mode.
• OPTICAL to switch to OPTICAL mode.
• COAXIAL to switch to COAXIAL mode.
• FM to switch to FM radio.
• DAB to switch to DAB radio.
Preset Equalizer
You can adjust the sound reproduced simply by choosing from 5 preset equalizers.
During play, press the EQ button on the remote control repeatedly to select: DEFAULT / POP / CLASSIC / ROCK / JAZZ.
Adjusting the Bass
Turn the – BASS + dial on the unit to adjust the intensity of the bass output sound.
Or press the BASS +/– button on the remote control.
If bass is adjusted, preset equalizer function is not available.
Adjusting the Treble
Turn the – TREBLE + dial on the unit to adjust the intensity of the treble output sound.
Or press the TREB +/– button on the remote control.
If treble is adjusted, preset equalizer function is not available.
The EQ settings (including BASS and TREBLE) are not available when you are using headphones. It is not a defect.
Adjusting the Display Brightness
Press DIMMER on the remote control to select the brightness level.
16
Page 17
SLEEP 15SLEEP OFF SLEEP 30
SLEEP 120 SLEEP 90 SLEEP 60
Clock Operation
In DAB / RDS station, the unit can synchronize with time transmitted by DAB / RDS station (with CT information) automatically.
Manually Setting the Clock
Manual setting the clock can only be done in Standby mode.
1. In Standby mode, press the CLOCK button to show the clock time on the display. Press and hold the CLOCK button until CLOCK SET scrolls across the display.
2. The hour indicator will blink. Press / buttons to set the hour.
3. Press CLOCK or ENTER on the remote control to conrm and the minute indicator will blink.
4. Press / buttons to set the minute.
5. Press the button on the unit or the / PAIR button on the remote control to switch between 12/24 hour format.
6. Press the CLOCK or ENTER button on the remote control to conrm.
• To exit timer setting mode without storing, press the button.
• If no button is pressed in approx. 60 seconds, the unit exits clock setting mode automatically.
• If a power failure occurs or the unit is disconnected from the mains, the clock setting will be lost.
Time Display
• During standby mode, press CLOCK to display the clock for approx 90 seconds.
• While the unit is on, press CLOCK to display the clock for few seconds.
Clock Synchronization
When in STANDBY mode, press the CLOCK button to show the clock time on the display. Press and hold button on the remote control, then press / buttons to select RADIO to synchronize or OFF for manual setting.
Sleep Timer
Use the sleep timer to turn the unit o after a certain number of minutes when in play mode. By setting the sleep timer, you can fall asleep to music and know that your unit will turn o by itself rather than play all night. The clock must be correctly set for the timer to operate correctly.
1. In On mode, press TIMER/SLEEP repeatedly to select your desired number of minutes. The number of minutes shown will display in this sequence:
2. When sleep timer is activated, the word “SLEEP” is displayed.
3. Press SLEEP to view the remaining time before switch o.
4. To cancel the sleep timer, press TIMER/SLEEP repeatedly until “SLEEPOFF” shows on the display.
17
Page 18
Daily Timer
You can use the setting timer to make the unit automatically turn on at a certain time every day from standby. The clock must be correctly set for the timer to operate correctly.
1. In Standby mode, press the CLOCK button to show the clock time on the display. Press and hold TIMER/SLEEP until “TIMER SET“ scrolls across the display. Then the hour indicator will blink.
2. Press / on the remote control to set the hour, then press the TIMER/SLEEP button to conrm. The minute indicator will blink.
3. Press / on the remote control to set the minute, then press the TIMER/SLEEP button to conrm. The mode will then blink on the display.
4. Press / on the remote control to set the mode.
a) DISC – sets alarm to wake to your DISC music.
b) FM – sets alarm to wake to select FM Radio Station.
c) DAB – sets alarm to wake to select DAB Radio Station.
d) USB – sets alarm to wake to USB music.
5. Press the TIMER/SLEEP button to conrm, then use / to adjust the alarm volume.
6. Press TIMER/SLEEP to conrm. The display will show “TMR ON / TMR OFF”.
7. Press / to select TMR ON or TMR OFF and press TIMER/SLEEP to conrm.
• If no button is pressed in approximately 60 seconds, the unit exits clock setting mode automatically.
• If DISC / USB source is selected and the audio cannot be played, TUNER is activated automatically.
• If timer is activated, the blue indicator will light up.
To Deactivate or Re-activate a Daily Timer
In Standby mode, repeatedly press TIMER/SLEEP on the remote control to activate or deactivate the timer.
DAB Radio Operation
Press the SOURCE button on the unit or press the DAB button on the remote control to select DAB source. The word “DAB” will be showed on the display.
1. If the unit is connected to the mains power and then switched on to DAB mode for the rst time, the unit will automatically start scanning. The display will show “SCANNING”.
2. All the stations that have been found will be stored automatically. To explore the found stations, press / buttons on the remote control.
3. To re-tune, press the INTRO/SCAN button on the remote control to perform a quick scan again.
18
Page 19
Auto Scan
The auto scan will search for the entire DAB Band III channels. After the scan has nished, the rst alphanumerically found station will be automatically selected.
1. Press the INTRO/SCAN button on the remote control to activate automatic program mode. The display will show “SCANNING” to indicate the progress of the scan and the number of stations found so far.
2. Once the scan has nished, the unit will display the total number of stations that have been found and a list of the found stations. All stations that have been found will be automatically stored.
You may press and hold / CLEAR button to clear the previously tuned stations before running an auto scan. The display will show CLEAR. All the tuned stations in both DAB and FM will be cleared.
Manual Tuning
As well as the auto tune function, you can also manually tune the receiver. This can help you when aligning your aerial or when adding stations that were missed while auto tuning.
1. Press and hold the / PAIR button to select Manual tune, the display will now show MANUAL TUNE”.
2. Press / to cycle through the DAB channels in the frequency range of 174.928MHz to 239.200MHz.
3. After your desired channel number is selected, press the ENTER button to conrm, display will now show “TUNING”. The unit will start to scan.
Secondary Services
You may see a “>>” symbol after the name of the station, this indicates that there are secondary services available to that station. These secondary services contain extra services that are related to the primary station. e.g. a sports station may want to add extra commentaries. The secondary services are inserted directly after the primary station in the station list.
To select the secondary station, press / until you nd the secondary service you want.
When the secondary service ends, the unit will automatically switch back to the primary station.
Presetting Stations
You can store up to 20 of your favourite stations to the memory. This will enable you to access your favourite stations quickly and easily.
1. To store a preset, you must rst be listening to the station that you would like to save.
2. Press the PROG button to activate program mode. The preset number will blink in the display.
3. Press ALBUM/PRESET / to select the desired station preset number.
4. Press the PROG button again to store the station, the display will show “SAVED”.
Recalling a Preset Station
Once you have saved a station, you can recall a preset station by pressing ALBUM/PRESET
/ . The band and frequency will be shown on the display, press ENTER to conrm.
19
Page 20
DAB Information Display
You can view the DAB service information in the following modes. Depending on the DAB radio station you are tuning to, some information modes may be unavailable. Press the INFO button repeatedly on the remote control to view the following information.
Station Name
When a DAB station is received, the name of that station will be displayed.
Ensemble Name
A multiplex is a collection of radio stations that are bundled and transmitted on one frequency. There are national and local multiplexes. Local ones contain stations that are specic to that area.
DAB – unlike normal radio, groups together several radio stations and transmits them on one frequency.
Clock
This displays the current time provided automatically by the broadcaster.
Date
This displays the current date provided automatically by the broadcaster.
DLS (Dynamic Label Segment)
Dynamic label segment is a scrolling message that the broadcaster may include with their transmissions. The message usually includes information, such as programme details etc.
Programme Type
This describes the style or genre of the programme that is being broadcast.
Channel Number
DAB digital radio can be broadcast on a wide number of frequencies.
Frequency
This shows the frequency of the current station.
Stereo/Mono
The display will show if the station being received is in mono or stereo.
Audio Bit Rate
The display will show the digital audio bit rate being received.
Signal Strength
The display will show “RSSI ##”, where ## is a number from 0-18.
20
Station Name
Ensemble Name
Clock
Date
DLS
Programme Type
Channel Number
Frequency
Stereo/Mono
Bit Rate
Signal Strength
Page 21
FM Radio Operation
• Make sure that you have correctly connected and fully extended the antenna.
• The search may not stop at a station with a very weak signal.
• If reception is still poor, try to adjust the DAB / FM aerial location.
Press the SOURCE button on the unit or press the FM button on the remote control to select FM mode.
Tuning in a Station
Auto Tuning
Press and hold / button on the remote control, the frequency changes down or up automatically until a station is found.
The search may not stop at a station with a very weak signal.
Manual Tuning
Press the / button repeatedly to change the frequency until you nd the station you want.
• With FM radio it may be necessary to ne tune each station by pressing / repeatedly. Each press will adjust the frequency by 0.05MHz. If reception is still poor adjust the position of the aerial or try moving the radio to another location.
• You may press and hold FM button to switch between STRONG and WEAK for station tuning.
• You may press and hold
auto scan. The display will show CLEAR. All the tuned stations in both DAB and FM will be cleared.
/ CLEAR button to clear the previously tuned stations before running an
Presetting Stations
You can store up to 20 of your favourite stations to the memory. This will enable you to access your favourite stations quickly and easily.
Automatically
Press the INTRO/SCAN button on the remote control to activate automatic tuning. The unit will automatically search and store the rst 20 radio stations it nds.
The rst programmed radio station will play automatically.
Manually
1. Tune into a desired radio station as shown above.
2. Press the PROG button on the remote to activate program mode. The preset number will ash in the display.
3. Press ALBUM/PRESET / to select the programme position number (1-20).
4. Press PROG again to store the station.
Preset Tuning
After the stations are preset (for details, please refer to the section “Presetting Stations” below), repeatedly press the ALBUM/PRESET / buttons on the remote control to select the desired preset number. Its band and frequency are displayed on the front panel. Press ENTER to conrm.
21
Page 22
RDS (Radio Data System) Reception
Many FM stations are broadcasting added data compatible with RDS (Radio Data System). This radio set oers convenient functions using such data.
Press the INFO button repeatedly to view the following information.
Station Name
When an RDS station is received, the name of that station will be displayed.
Tex t
The broadcaster can include a message that displays information about the current programme.
Programme Type
This describes the “Style” or “Genre” of music that is being broadcast, e.g. “Rock” or “Classical”.
Stereo/Mono
The display will show if the station being received is in mono or stereo.
Clock
The RDS CLOCK system may not properly operate in areas where RDS CLOCK service is not available. Once RDS CLOCK service is available, the RDS CLOCK system will commence operation.
Date
This displays the current date provided automatically by the broadcaster.
Frequency
This shows the frequency of the current station.
Station Name
Tex t
Program Type
Stereo/Mono
Clock
Date
Frequency
22
Page 23
CD/MP3 Operation
Compatible Disc Types
Disc Types Disc Logo Recorded Content
CD-R (CD Recordable - Audio/MP3) AUDIO / MP3
CD-RW (CD-Rewritable - Audio/MP3) AUDIO / MP3
AUDIO-CD (Compact Disc Digital Audio) AUDIO
• Some recorded les may not be able to be played due to the type and format of disc or condition of the recording.
• If you are having trouble playing a certain disc, it is recommended to use USB input instead for best MP3 playback.
Press the SOURCE button on the unit or the CD button on the remote control to select the
DISC source. The word “DISC” will be showed on the display.
Playback
1. In DISC mode, press button on the unit to open the disc tray.
2. Place the disc with the label side up into the CD compartment, and then press the button on the unit to close the tray.
3. After closing the disc tray, the unit will read the disc and play it automatically.
• If there is no disc or the disc can’t be read, “NO DISC” will show on the display.
• If in stop mode, please press the button to start playing the disc.
• Take care not to clip your ngers in the moving tray and door.
4. Press on the unit or on the remote to pause the playback, the display will show “PAUSE“. To resume playback, press on the unit again or / PAIR on the remote.
5. Press to stop the disc playing. Press button if you want to remove the disc in DISC mode only.
To Skip Search or Search and Play
• Press once or more to skip to beginning of the current track or the previous track.
• Press once or more to skip forward to the next track.
• Press and hold / to search for the position that you intend to start playing.
Release to resume normal playback.
Selecting an Album (for MP3 disc)
• Press ALBUM/PRESET / to select the next / previous album, and play the rst track of this album.
• If the playing has ended, press ALBUM/PRESET / to select the next / previous album.
23
Page 24
Repeat Playback
ONE and ALL Repeat Play
• CD Disc
Press the REPEAT/SHUFFLE button repeatedly to set the function. The selected mode will show on the display.
RPT ONE : Repeat the same track.
RPT ALB : Repeats all tracks in a folder (if a folder is displayed)
RPT ALL : Repeat all tracks.
SHUFFLE : Plays tracks randomly.
OFF : Turns o REPEAT/SHUFFLE.
Intro Playback
Press the INTRO/SCAN button on the remote control. The unit will play the rst 10 seconds of each track.
Press the INTRO/SCAN button again to resume normal playback.
Text Display During Playback
CD Disc
Repeatedly press INFO to show the current track number and single remain time / single remain time / total elapsed time / total remain time.
MP3 Disc
• If the track playing contains ID3 information, when playback begins, the le name will scroll on the screen automatically. Repeatedly press INFO to show the current track number and single remain time / total elapsed time / total remain time.
• If the track playing has no ID3 information, press INFO to show the current track and track of time.
Programme Play
You can programme up to 20 tracks to play in any desired order.
1. Make sure the disc is inserted and the unit is in STOP mode.
2. Press the PROG button on the remote to enter MEMORY mode.
3. Press the number (0-9) buttons or / on the remote control to select the track you wish to preset.
4. Press PROG to store.
5. Repeat steps 3-4 to program more tracks.
6. Once programming is complete, press the button on the unit or / PAIR button on the remote to start programme play.
7. Press once to stop programme play. Press twice to clear programme. Press again to stop playback.
Open the CD tray and close it again will cancel the programme and erase the memory.
24
Page 25
Using the USB
By connecting a USB mass storage device (including USB ash memory, USB ash players or memory cards) to this unit, you can enjoy the device’s stored music through the unit.
1. Insert the USB device’s USB plug into the socket at the front of unit.
2. Press the SOURCE button on the unit or USB button on the remote control to select the USB source. The word “USB” will be shown on the display.
3. All playback features are the same as if you were playing an MP3 CD.
• The player supports the USB music le format of MP3 only.
• If your USB device is loaded with MP3 les but the display keeps showing ‘NO USB” on the display, the
format of your USB device might not be compatible with the unit.
• The unit can support USB devices with up to 64GB of memory.
• The unit may not be compatible with all USB devices, this is not an indication of a problem with the
unit.
AUX / OPTICAL / COAXIAL Operation
1. While in ON mode, press the SOURCE button on the unit or press AUX / OPTICAL / COAXIAL on the remote control to select the AUX / OPTICAL / COAXIAL source. The
corresponding mode will be shown on the display.
2. Operate your audio device directly for playback features.
3. Press VOL + / – to adjust the volume to your desired level.
While using COAXIAL / OPTICAL mode, ensure the audio setting of the input source (e.g. TV, games console, DVD player, etc.) is set to PCM (Refer to the user manual of the input source device for its audio setting details) with optical / coaxial output.
25
Page 26
Bluetooth® Operation
Pairing the unit with a Bluetooth® device to listen to music:
1. Press the SOURCE button on the unit or directly press the BT button on the remote control to select the Bluetooth® mode. The display will show “BT READY”.
2. Activate your Bluetooth® device and select the search mode. “UX-D427S” will appear on your Bluetooth® device list.
3. If you cannot nd the unit, press and hold the button on the unit or / PAIR button on the remote to enter PAIRING MODE. The unit display will show “PAIR” and the voice prompt “PAIRING“ will be heard.
4. Select “UX-D427S” and enter “0000” for the password if necessary. If connection is successful, the display will show “BT” followed by the voice prompt stating “PAIRED”.
5. To disconnect the Bluetooth® function, switch to another function on the unit or disable the function from your Bluetooth® device. You will hear “DISCONNECTED” from the voice prompt.
If your Bluetooth® device supports A2DP, play music via your device. If your Bluetooth® device supports AVRCP, use supplied remote control to control play.
• To pause / resume playback, press .
• To skip to a track, press / .
• To increase or decrease the volume, press VOL + / – .
• The operational range between the unit and the device is approximately 8 metres.
• Before connecting a Bluetooth® device to the unit, ensure you know the device’s capabilities.
• Compatibility with all Bluetooth® devices is not guaranteed.
• Any obstacle between the device and the unit can reduce operational range.
• Keep this player away from other electronic devices that may cause interference.
• If no other Bluetooth® devices pairs with this unit within 2 minutes, the unit will recover to its previous
connection.
• The player will also be disconnected when your device is moved beyond the operational range.
26
Page 27
Maintenance
Cleaning the Unit
Ensure the unit is fully unplugged from the mains socket before cleaning.
• To clean the units, wipe the case with a slightly moist, lint-free cloth.
• Do not use any cleaning uids containing alcohol, ammonia or abrasives.
• Do not spray aerosol at or near the unit.
Removing, Installation the Grill and Cleaning the Speakers
The grill is held by pins. To remove the grill, pull gently around the edge away from the speaker, slowly working your way from one end of the speaker to the other.
To re-install, align the grill pins with the cups in the speaker and push into place.
Use a dampened soft cloth or paper towel to clean the cabinet. The grill is best cleaned by brushing it o with a lint-free cloth.
When cleaning the speakers without grills, beware of making a punch or push a small dent on a speaker’s dust cap. These damages might aect the speaker’s performance.
Handling Discs
• Do not touch the playback side of the disc.
• Do not attach paper or tape to the disc.
Cleaning Discs
• Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the centre outwards with a soft cloth. Always keep the disc clean.
Playback side
• If you cannot wipe o the dust with a soft cloth, wipe the disc lightly with a slightly moistened soft cloth and nish with a dry cloth.
• Do not use any type of solvent such as thinner, benzine, commercially available cleaners or antistatic spray. They may damage the disc.
27
Page 28
Storing Discs
• Do not store discs in places subjected to direct sunlight or near heat sources.
• Do not store discs in places subjected to moisture and dust such as a bathroom or near
a humidier.
• Storing discs vertically in a case, stacking discs or placing objects on discs outside of their cases may cause warping.
Hints and Tips
If a problem does occur, it may often be due to something very minor. The following table contains various tips. If you require additional assistance
• For UK, please call our UK Call Centre on 0344 561 1234.
• For Ireland, please call our Ireland Call Center on 1 890 818 575.
General
Problem Solution
No power. • Ensure the mains plug is connected.
• Make sure that you select the ON mode.
The remote control does not function.
No sound from the unit. Please try either one of the solutions below:
The unit does not respond when pressing any buttons.
• Use the remote control near the unit.
• Point the remote control at the remote sensor on the unit.
• Replace the battery in the remote control with a new one.
• Remove any obstacles between the remote control and
the unit.
• Make sure that the unit is not muted. Press the or the VOL + / – on the remote control, or turn the – VOLUME + dial on the unit to resume normal listening.
• Press on the unit or on the remote control to switch the unit to standby mode. Then press the button again to switch the unit on.
• Unplug the unit from the mains socket, then plug it in again. Switch on the unit.
• The unit may freeze up during use. Switch the unit o and then on again at the mains socket to reset the unit.
28
CD
Problem Solution
Disc in place but the unit won’t play.
Disc skips • Make sure the unit is on a secure spot. Vibrations or
• Make sure you’ve selected CD mode.
• Make sure the disc label is facing up.
• Make sure the disc is clean.
• PAUSE mode may be activated, deactivate it.
• Disc may be damaged or dirty; check and clean the disc.
jarring can cause the disc to skip.
Page 29
Radio
Problem Solution
Poor radio reception. • Electrical interference in your home can cause poor
reception. Move the unit away from them (especially those with motors and transformers).
Desired station not found.
FM
• Weak signal. Search manually.
• If reception is still poor, adjust the position of the aerial.
DAB
• No DAB coverage in your area or poor reception. Adjust the position of the aerial.
• Perform a system reset and then a DAB full scan.
Bluetooth®
Problem Solution
I cannot nd “UX-D427S” on my Bluetooth® device.
If any functional abnormality is encountered, unplug the unit from the mains socket and reconnect it again.
• Ensure the Bluetooth® function is activated on your Bluetooth® device.
• Ensure you have paired your unit with the Bluetooth® device.
29
Page 30
Product Fiche and Specifications
Brand JVC
Model UX-D427S
System Section
Power Supply 220V-240V~ 50/60Hz
Power Consumption 55 W
THD ≤ 1%
Bluetooth® Bluetooth®
Version
Maximum power transmitted
Frequency bands
Unit Dimension 245 (W) × 294 (D) × 139 (H) mm
Speakers Section
Impedance 3 Ω
Output Power 2 × 80 Watts RMS
Speaker Box Dimension 175 (W) × 249 (D) × 262 (H) mm
Radio Section
Frequency Range DAB 174.928 – 239.200 MHz (Band III)
Compact Disc Section
Optical Pickup 3 - Beam Laser
Frequency Response 45 Hz – 20 kHz
USB Section
USB Memory Stick Memory Size
Features and specications are subject to change without prior notice.
V3.0
7 dBm
2402 MHz - 2480 Mhz
FM 87.5 – 108 MHz
Up to 64 GB
30
Page 31
Useful Information and Licences
For general information about appliances, and handy hints and tips check out Kit Guides at teamknowhow.com or call UK: 0344 561 1234 Ireland: 1890 818 575
Visit Partmaster.co.uk today for the easiest way to buy electrical
spares and accessories. With over 1 million spares and accessories available we can deliver direct to your door the very next day. Visit www.partmaster.co.uk or call 0344 800 3456 (UK customers only). Calls charged at National Rate.
This radio is future-ready and can receive the available DAB, DAB+
and FM radio stations.
The symbol on the product or its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.
For more information about where you can drop o your waste for recycling, please contact your local authority, or where you purchased your product.
Notes for Battery Disposal
The batteries used with this product contain chemicals that are harmful to the environment. To preserve our environment, dispose of used batteries according to your local laws or regulations. Do not dispose of batteries with normal household waste.
For more information, please contact the local authority or your retailer where you purchased the product.
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by DSG Retail Limited is under license. Other trademarks and trade names are those of their respective owners.
Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
All trademarks are the property of their respective owners and all rights are acknowledged.
31
Page 32
Dear Customer,
This apparatus is in conformance with the valid European directives compatibility and electrical safety.
European representative of the manufacturer is: DSG Retail Ltd. (co. no. 504877) 1 Portal Way, London, W3 6RS, UK
For Help and Support Call
UK: 0344 561 1234
Ireland: 1890 818 575
The product is distributed and warranted exclusive by DSG Retail Ltd.
“JVC” is the trademark of JVC KENWOOD Corporation, used by DSG Retail Ltd. under license.
(IB-UX-D427S-180625V3)
Loading...