JVC TM-H1750CGE, TM-H1950CGE User Manual

COLOR VIDEO MONITOR

BEDIENUNGSANLEITUNG : FARB-VIDEO-MONITOR MANUEL D’INSTRUCTIONS : MONITEUR VIDÉO COULEUR MANUALE DI ISTRUZIONI : MONITOR VIDEO A COLORI INSTRUCCIONES : MONITOR DE VIDEO A COLOR

 !"#$%&'(&)

ENGLISH

TM-H1950CG TM-H1750CG

For Customer Use:

Enter below the Serial No. which is located on the rear of the cabinet. Retain this information for future reference.

Pour l’usage du client:

Enter ci-dessous le numéro de série qui est situé sur l’arrière du coffret. Conserver cette information pour une référence ultérieure.

Model No. :

Numéro de modèle :

Serial No. :

Numéro de série :

INSTRUCTIONS

DEUTSCH

FRANÇAIS

ITALIANO

ESPAÑOL

COLOR

CHROMA

CONTRAST

VOLUME/SELECT

BRIGHT

PHASE

TM-H1950CG

(TM-H1950CG shown) (Gezeigtes Modell ist TM-H1950CG) (TM-H1950CG montré) (Modello TM-H1950CG) (Muestra de TM-H1950CG) (

qjJeNVRM`d 

UNDER

OFF

SCAN

BLUE

CHECK

ASPECT

INPUT SELECT

SLOT

POWER



)

LCT1025-002B-H

INSTRUCTIONS

COLOR VIDEO MONITOR

TM-H1950CG TM-H1750CG

ENGLISH

Thank you for purchasing this JVC color video monitor. Before using it, read and follow all instructions carefully to take full advantage of the monitor’s capabilities.

SAFETY PRECAUTIONS

In order to prevent any fatal accidents caused by misoperation or mishandling the monitor, be fully aware of all the following precautions.

WARNINGS

To prevent fire or shock hazard, do not expose this monitor to rain or moisture. Dangerous high voltages are present inside the unit. Do not remove the back cover of the cabinet. When servicing the monitor, consult qualified service personnel. Never try to service it yourself.

WARNING : THIS APPARATUS MUST

BE EARTHED.

Machine Noise Information Ordinance 3. GSGV, January 18, 1991: The sound pressure level at the operator position is equal or less than 70 dB(A) according to ISO 7779.

Improper operations, in particular alternation of high voltage or changing the type of tube may result in x-ray emission of considerable dose. A unit altered in such a way no longer meets the standards of certification, and must therefore no longer be operated.

FCC INFORMATION (U.S.A. only)

CAUTION: Changes or modification not approved by

JVC could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and

receiver.

– Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV

technician for help.

This monitor is equipped with a 3-blade grounding-type plug to satisfy FCC rule. If you are unable to insert the plug into the outlet, contact your electrician.

PRECAUTIONS

● Use only the power source specified on the unit.

(120 V AC/230 V AC, 50 Hz/60Hz)

● When not using this unit for a long period of time, or when

cleaning it, be sure to disconnect the power plug from the AC outlet.

● Do not allow anything to rest on the power cord. And do not

place this unit where people will tread on the cord. Do not overload wall outlets or power cords as this can result in a fire or electric shock.

● Avoid using this unit under the following conditions:

– in extremely hot, cold or humid places, – in dusty places, – near appliances generating strong magnetic fields, – in places subject to direct sunlight, – in badly ventilated places, – in automobiles with doors closed.

● Do not cover the ventilation slots while in operation as this

could obstruct the required ventilation flow.

● When dust accumulates on the screen surface, clean it with

a soft cloth.

Notice (U.S.A. only)

This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://

● Unplug this unit from the AC outlet and refer servicing to

qualified service personnel under the following conditions: – when the power cord is frayed or the plug is damaged, – if liquid has been spilled into the unit, – if the unit has been dropped or the cabinet has been

damaged,

– when the unit exhibits a distinct change in performance.

● Do not attempt to service this unit yourself as opening or

removing covers may expose you to dangerous voltage or other hazards. Always refer servicing to qualified service personnel.

● When replacement parts are required, have the service

personnel verify in writing that the replacement parts he/she uses have the same safety characteristics as the original parts. Use of manufacture’s specified replacement parts can prevent fire, shock, or other hazards.

● Upon completion of any servicing or repair work to this unit,

please ask the service personnel to perform the safety check described in the manufacturer’s service literature.

● When this unit reaches the end of its useful life, improper

disposal could result in a picture tube implosion. Ask qualified service personnel to dispose of this unit.

www.eiae.org.>

POWER CONNECTION

The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada only) and AC 230 V (For European countries or United Kingdom), the power cord attached conforms to the following power supply voltage and countries. Use only the power cord designated to ensure Safety and EMC regulations of each countries.

Power cord

Power supply voltage : AC 120 V AC 230 V AC 230 V Countries : U.S.A. and Canada European countries United Kingdom

Warning:

● Do not use the same Power Cord for AC 120 V as for AC 230 V. Doing so may cause malfunction, electric shock

or fire.

Note for the United Kingdom power cord only

The plug on the United Kingdom power cord has a built-in fuse. When replacing the fuse, be sure to use only a correctly rated approved type, re-fit the fuse cover. (Consult your dealer or qualified service personnel.)

How to replace the fuse

Open the fuse compartment with the blade screw driver, and replace the fuse. (* An example is shown in the illustration.)

Fuse

SCREEN BURN

● It is not recommended to keep a certain still image displayed on screen for a long time as well as displaying extremely bright

images on screen. This may cause a burning (sticking) phenomenon on the screen of cathode-ray tube. This problem does not occur as far as displaying normal video playback motion images.

 Supplementary Explanation

= Information for monitor operation =

This monitor uses a high precision CRT (cathode ray tube). Please follow the procedures below. * For stable operation of the CRT, approximately 30 minutes running time is required from the time the power is turned on. * When the monitor is installed, it can be easily affected by surrounding magnetic fields, which can generate irregular color

on the screen. When it is difficult to eradicate, degauss from outside using a degausser, etc.

ENGLISH

SAFETY PRECAUTIONS ................................................................................. 2

CONTROLS AND FEATURES ......................................................................... 4

CONTROLS AND FEATURES (INPUT CARD: OPTIONAL) ........................... 7

PREPARATION................................................................................................. 8

 INSTALLING THE INPUT CARD .............................................................. 8

 ATTACHING THE POWER CORD HOLDER ............................................ 9

HOW TO HANDLE BASIC OPERATIONS ..................................................... 10

HOW TO USE THE MENU FUNCTIONS........................................................ 12

HOW TO INITIALIZE THE SETTING.............................................................. 15

BASIC CONNECTION EXAMPLE.................................................................. 16

HOW TO USE EXTERNAL CONTROL .......................................................... 18

TROUBLESHOOTING.................................................................................... 19

SPECIFICATIONS .......................................................................................... 20

APPENDIX ...................................................................................................... 22

CONTROLS AND FEATURES

POWER

CHROMA

ASPECT

INPUT SELECT

UNDER SCAN

COLOR OFF

BLUE CHECK

PHASE

TM-H1950CG

BRIGHT

CONTRAST

VOLUME/SELECT

SLOT

8 9 10 11 12 1413

POWER

CHROMA MENU

ASPECT

INPUT SELECT

UNDER

SCAN

COLOR

OFF

BLUE

CHECK

PHASE BRIGHT

CONTRAST VOLUME/SELECT

SLOT

FRONT VIEW

(Front view of TM-H1950CG shown)

Tally lamp

Lights when the tally control signal is ON. The tally control signal is input through the REMOTE (external control) remote terminal. For details, refer to Page 18.

Chroma/Phase button

CHROMA/ PHASE]

[

Press this button to activate the picture color density adjustment mode or picture hue adjustment mode. Each time you press the button, the adjustment item changes.

Picture color density

Adjust the value with the VOLUME/SELECT buttons Also used as a control button in the menu function mode.

Contrast/Brightness button

[CONTRAST

Press this button to activate the picture contrast adjustment mode or picture brightness adjustment mode. Each time you press the button, the adjustment item changes.

Picture contrast

Adjust the value with the VOLUME/SELECT buttons Also used as a control button in the menu function mode.

Volume/Select buttons

[VOLUME/SELECT –

Adjusts the speaker volume. Also used as a control button in the menu function mode.

Menu button [MENU]

Displays and disappears the <MENU> screen. Pressing the CHROMA/PHASE button button depressed will display the <SET-UP MENU> screen.

Under Scan button [UNDER SCAN]

Reduces the screen size to display the entire image. Press the button again to cancel Under Scan. When selected, the Under Scan button lights.

Color Off button [COLOR OFF]

Cuts color signals to display a black and white image. Press the button again to restore the original color. When selected, the COLOR OFF button lights.

Note:

● This function is invalid with RGB input.

f Picture hue

/ BRIGHT ]

f Picture brightness

2 with the Menu

Blue Check button [BLUE CHECK]

Cuts red and green signal components. Only blue signal components are shown. Press the button again to restore the normal image. When selected, this button lights.

Aspect button [ASPECT]

Press this button to change the aspect ratio from 4:3 to 16:9.

Input A (VIDEO) button [INPUT SELECT A]

Selects the video and audio signals input to the VIDEO A

* and AUDIO A q terminals on the rear panel. The

button lights when selected.

Input B (VIDEO Y/C) button [INPUT SELECT B]

Selects the video and audio signals input to the VIDEO B

( or VIDEO B (Y/C) ) and AUDIO B w terminals on

the rear panel. The button lights when selected.

Note:

● The VIDEO B terminals include a video terminal (BNC

Input C/D (Slot) buttons [INPUT SELECT C/D

(SLOT)]

Selects the signals to be input via the input cards installed in the rear panel card slots.

C, D: Selects the image from the input card in the slot.

Power indicator

Unlit : The main power is OFF. Orange : The main power is ON, but the monitor’s power

Green : The main power is ON, and the monitor’s power

Power switch [POWER ]

Press the power switch to turn the monitor’s power ON or OFF when the main power is ON.

Note:

● When RUSH DELAY is set to SLOW, it takes about

Speaker

A built-in speaker is located inside the right side panel when the monitor is viewed from the front.

connector) and a Y/C terminal (mini-DIN 4-pin connector). The Y/C (S-video) terminal has priority.

For details on input connectors and using the INPUT SELECT button, refer to page 7.

is OFF (in the stand-by mode).

is ON (in the normal operation mode).

three seconds before power is actually supplied after the power switch is pressed.

VIDEO A

AUDIO A

AUDIO B

VIDEO B

IN OUT

OUT

Y/C

OUT

VIDEO A

REMOTE

SLOT

AUDIO A

AUDIO B

VIDEO B

IN OUT

OUT

Y/C

OUT

REAR VIEW

Input card slot (SLOT)

Optional input cards can be installed in this slot. Input cards are not provided when you purchase this monitor.

REMOTE (external control) terminal

Connect this terminal to an external control unit to enable remote operation of the monitor. Refer to the HOW TO USE EXTERNAL CONTROL on page 18 for more details.

Video A terminals [VIDEO A IN/OUT]

Video signal input (IN) and output (OUT) terminals. The output terminal is bridge-connected. (The input signal is automatically terminated if a cable is not connected to the OUT terminal.)

IN : Video signal input terminal OUT : Bridge-connected video signal output terminal

Notes:

* For corresponding audio signals, use the AUDIO A

terminals

* Also refer to BASIC CONNECTION EXAMPLE

on page 16.

Video B terminals [VIDEO B IN/OUT]

Video signal input (IN) and output (OUT) terminals. The output terminal is bridge-connected. (The input signal is automatically terminated if a cable is not connected to the OUT terminal.)

IN : Video signal input terminal OUT : Bridge-connected video signal output terminal

Notes:

* For corresponding audio signals, use the AUDIO B

terminals

* Also refer to BASIC CONNECTION EXAMPLE on

page 16.

(Rear view of TM-H1950CG shown)

Video B (Y/C) terminals [VIDEO B Y/C IN/OUT]

Y/C (S-video) signal input (IN) and output (OUT) terminals. The output terminal is bridge-connected. (The input signal is automatically terminated if a cable is not connected to the OUT terminal.) IN : Y/C-separated (S-video) video signal input

terminal

ENGLISH

OUT : Bridge-connected Y/C-separated (S-video) signal

output terminal.

Notes:

* For corresponding audio signals, use the AUDIO B

terminals

* When both VIDEO B terminals are connected (input) at

the same time, the Y/C terminal has priority.

* Also refer to BASIC CONNECTION EXAMPLE

on page 17.

Audio A terminals [AUDIO A IN/OUT]

Input (IN) and output (OUT) terminals for the audio signal corresponding to the VIDEO A terminals

The output terminal is bridge-connected.

IN : Audio signal input terminal OUT : Bridge-connected audio signal output terminal

Notes:

* For corresponding video signals, use the VIDEO A

terminal

* Also refer to BASIC CONNECTION EXAMPLE

on pages 16 and 17.

Audio B terminals [AUDIO B IN/OUT]

Input (IN) and output (OUT) terminals for the audio signals corresponding to the VIDEO B terminals VIDEO B (Y/C) terminals

( or

The output terminal is bridge-connected.

IN : Audio signal input terminal OUT : Bridge-connected audio signal output terminal

Notes:

* For corresponding video signals, use the VIDEO B

terminals

( or VIDEO B (Y/C) terminals ).

* Also refer to BASIC CONNECTION EXAMPLE

on pages 16 and 17.

VIDEO A

REMOTE

SLOT

AUDIO A

AUDIO B

VIDEO B

IN OUT

OUT

Y/C

OUT

24 23

CONTROLS AND FEATURES (cont’d)

REAR VIEW

To AC outlet (120 V AC, 50 Hz/60 Hz)

To AC outlet (230 V AC, 50 Hz/60 Hz)

For U.S.A. and Canada

For Europe

(Rear view of TM-H1950CG shown)

For the United Kingdom

Main power switch

Press the switch to turn the main power ON or OFF. When the main power is ON, the power indicator on the front panel lights in orange and the monitor enters the stand-by mode. I : ON  : OFF

AC inlet [AC IN]

Power input connector. Connect the provided AC power

t to an AC outlet (120 V AC or 230 V AC,

cord 50 Hz/60 Hz).

Power cord

Connects the provided power cord (120 V AC or 230 V AC, 50 Hz/60 Hz) to the AC IN connector

Caution:

In North America (USA and Canada), this monitor comes with one power cable. In Europe and the United Kingdom, two power cables are provided (one for use in continental European countries and the other for the UK). Be sure to use the power cable that is appropriate for the AC outlets used in your region. If none of the power cables provided is suitable, please contact your dealer or qualified service personnel to obtain the correct type of power cable.

CONTROLS AND FEATURES

B/PB/B-Y

G/Y

OUTIN

R/PR/B-Y

OUTIN

HD/C

OUTIN

AUDIO

OUT

AUDIO 2

AUDIO 1

OUT

SWITCHED

OUT

SDI 1

SDI 2

(INPUT CARD: OPTIONAL)

 COMPONENT/RGB INPUT CARD (OPTIONAL:

IF-C01COMG)

Video input/output terminals

Input (IN) and output (OUT) terminals for component (color deference) or RGB signals. The IN and OUT terminals are bridge-connected. (When no cable is connected to the OUT terminal, the input signal is automatically terminated.) Select component signal : press INPUT SELECT C button Select RGB signal : press INPUT SELECT D button

Synchronized signal input/output terminals

Input (IN) and output (OUT) terminals for the vertical, horizontal or complex synchronized signals.

External sync is available with RGB input only.

The IN and OUT terminals are bridge-connected. (When no cable is connected to the OUT terminal, the input signal is automatically terminated.) G on SYNC cannot be used with RGB input.

Audio input/output terminals

Input (IN) and output (OUT) terminals for audio signals. The IN and OUT terminals are bridge-connected.

Connection terminal (to a Color Video Monitor)

Attach to the connection terminal of your color video monitor.

 SDI INPUT CARD (OPTIONAL: IF-C01SDG)

Output terminal for a selected component

serial digital signal

Output terminal for a selected digital signal (the input displayed on the screen). The output signal is cablecompensated. NOTE: When the monitor’s main power is OFF, no digital

signal is output. In the standby mode, the signal from the SDI 1 terminal is output.

Input terminals for component serial digital

signals

Input terminals for the digital signal. Select SDI 1 : press INPUT SELECT C button

Note:

● The optional input cards shown below cannot be used.

Using any of these cards will void your warranty and may result in damage or malfunction. *Video input card (IF-C01PNG) *HD-SDI input card (IF-C01HSDG) *HD-SDI input card (IF-C12HSDG)

Select SDI 2 : press INPUT SELECT D button

Audio input/output terminals

Input (IN) and output (OUT) terminals for the analog signals corresponding to SDI 1 and SDI 2. NOTE: This input card cannot decode audio data even if

contained in the input digital signal.

Connection terminal (to a Color Video

Monitor)

Attach to the connection terminal of your color video monitor.

ENGLISH

+ 17 hidden pages

JVC TM-H1750CGE, TM-H1950CGE User Manual

SAFETY PRECAUTIONS

CONTENTS

CONTROLS AND FEATURES

FRONT VIEW

REAR VIEW

 SDI INPUT CARD (OPTIONAL: IF-C01SDG)