BEDIENUNGSANLEITUNG :FARB-VIDEO-MONITORMANUEL D’INSTRUCTIONS :MONITEUR VIDEO COULEURMANUALE DI ISTRUZIONI :MONITOR VIDEO A COLORIINSTRUCCIONES :MONITOR DE VIDEO A COLOR
!"#$%&'(&)
[ TM-H1750CG/E / TM-H1750CG/U ]
ENGLISH
TM-H1750CG
For Customer Use:
Enter below the Serial No. which is located on the rear of the cabinet.
Retain this information for future reference.
Pour l’usage du client:
Enter ci-dessous le numéro de série qui est situé sur l’arrière du coffret.
Conserver cette information pour une référence ultérieure.
Model No. :
Numéro de modèle :TM-H1750CG
Serial No. :
Numéro de série :
CHROMAMENU
PHASE
TM-H1750CG
CONTRAST VOLUME/SELECT
BRIGHT
INSTRUCTIONS
UNDER
COLOR
BLUE
AB
ASPECT
SCAN
OFF
CHECK
INPUT SELECT
CD
SLOT
POWER
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
LCT1025-001A-H
1101-Y-U-JMT
Jan. 2002 No. 51923
Page 2
1-2
No.51923
2
SAFETY PRECAUTIONS
In order to prevent any fatal accidents caused by misoperation
or mishandling the monitor, be fully aware of all the following
precautions.
WARNINGS
To prevent fire or shock hazard, do not expose this
monitor to rain or moisture. Dangerous high voltages
are present inside the unit. Do not remove the back
cover of the cabinet. When servicing the monitor,
consult qualified service personnel. Never try to service
it yourself.
WARNING : THIS APPARATUS MUST
Machine Noise Information Ordinance 3. GSGV,
January 18, 1991: The sound pressure level at the
operator position is equal or less than 70 dB(A)
according to ISO 7779.
Improper operations, in particular alternation of high
voltage or changing the type of tube may result in x-ray
emission of considerable dose. A unit altered in such a
way no longer meets the standards of certification, and
must therefore no longer be operated.
This monitor is equipped with a 3-blade grounding-type
plug to satisfy FCC rule. If you are unable to insert the
plug into the outlet, contact your electrician.
PRECAUTIONS
● Use only the power source specified on the unit.
(120 V AC/230 V AC, 50 Hz/60Hz)
● When not using this unit for a long period of time, or when
cleaning it, be sure to disconnect the power plug from the
AC outlet.
● Do not allow anything to rest on the power cord. And do not
place this unit where people will tread on the cord. Do not
overload wall outlets or power cords as this can result in a
fire or electric shock.
● Avoid using this unit under the following conditions:
– in extremely hot, cold or humid places,
– in dusty places,
– near appliances generating strong magnetic fields,
– in places subject to direct sunlight,
– in badly ventilated places,
– in automobiles with doors closed.
● Do not cover the ventilation slots while in operation as this
could obstruct the required ventilation flow.
● When dust accumulates on the screen surface, clean it with
a soft cloth.
BE EARTHED.
FCC INFORMATION (U.S.A. only)
CAUTION: Changes or modification not approved by
JVC could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
Notice (U.S.A. only)
This product utilizes both a Cathode Ray Tube (CRT) and
other components that contain lead. Disposal of these
materials may be regulated in your community due to
environmental considerations. For disposal or recycling
information please contact your local authorities, or the
Electronics Industries Alliance: <http://
● Unplug this unit from the AC outlet and refer servicing to
qualified service personnel under the following conditions:
– when the power cord is frayed or the plug is damaged,
– if liquid has been spilled into the unit,
– if the unit has been dropped or the cabinet has been
damaged,
– when the unit exhibits a distinct change in performance.
● Do not attempt to service this unit yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Always refer servicing to qualified service
personnel.
● When replacement parts are required, have the service
personnel verify in writing that the replacement parts he/
she uses have the same safety characteristics as the
original parts. Use of manufacture’s specified replacement
parts can prevent fire, shock, or other hazards.
● Upon completion of any servicing or repair work to this unit,
please ask the service personnel to perform the safety
check described in the manufacturer’s service literature.
● When this unit reaches the end of its useful life, improper
disposal could result in a picture tube implosion. Ask
qualified service personnel to dispose of this unit.
www.eiae.org.>
POWER CONNECTION
The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada only) and AC 230 V (For European countries
or United Kingdom), the power cord attached conforms to the following power supply voltage and countries. Use only the power
cord designated to ensure Safety and EMC regulations of each countries.
Power cord
Power supply voltage : AC 120 VAC 230 VAC 230 V
Countries : U.S.A. and CanadaEuropean countriesUnited Kingdom
Warning:
●
Do not use the same Power Cord for AC 120 V as for AC 230 V. Doing so may cause malfunction, electric shock
or fire.
Note for the United Kingdom power cord only
The plug on the United Kingdom power cord has a built-in fuse. When replacing the fuse, be sure to use only a correctly rated
approved type, re-fit the fuse cover.
(Consult your dealer or qualified service personnel.)
How to replace the fuse
Open the fuse compartment with the blade screw driver, and
replace the fuse.
(* An example is shown in the illustration.)
SCREEN BURN
● It is not recommended to keep a certain still image displayed on screen for a long time as well as displaying extremely bright
images on screen. This may cause a burning (sticking) phenomenon on the screen of cathode-ray tube. This problem does
not occur as far as displaying normal video playback motion images.
Lights when the tally control signal is ON. The tally control
signal is input through the REMOTE (external control)
remote terminal. For details, refer to Page 17.
Chroma/Phase button
2
CHROMA/ PHASE]
[
Press this button to activate the picture color density
adjustment mode or picture hue adjustment mode. Each
time you press the button, the adjustment item changes.
Picture color density
Adjust the value with the VOLUME/SELECT buttons
Also used as a control button in the menu function mode.
Contrast/Brightness button
3
[CONTRAST / BRIGHT ]
Press this button to activate the picture contrast adjustment
mode or picture brightness adjustment mode. Each time
you press the button, the adjustment item changes.
Picture contrast
Adjust the value with the VOLUME/SELECT buttons
Also used as a control button in the menu function mode.
Volume/Select buttons
4
[VOLUME/SELECT –
Adjusts the speaker volume. Also used as a control
button in the menu function mode.
Menu button [MENU]
5
Displays and disappears the <MENU> screen.
Pressing the CHROMA/PHASE button
button depressed will display the <SET-UP MENU>
screen.
Under Scan button [UNDER SCAN]
6
Reduces the screen size to display the entire image.
Press the button again to cancel Under Scan.
When selected, the Under Scan button lights.
Color Off button [COLOR OFF]
7
Cuts color signals to display a black and white image.
Press the button again to restore the original color.
When selected, the COLOR OFF button lights.
POWER
AB
CD
SLOT
ASPECT
SCAN
OFF
CHECK
INPUT SELECT
f
f
Picture brightness
Note:
● This function is invalid with RGB input.
REAR VIEW
<Rear Panel>
UNDER
COLOR
BLUE
SCAN
OFF
CHECK
56
4
8
9
10
4
.
11
8 9 10 11121413
7
Blue Check button [BLUE CHECK]
Cuts red and green signal components. Only blue signal
components are shown. Press the button again to
restore the normal image.
When selected, this button lights.
Aspect button [ASPECT]
Press this button to change the aspect ratio from 4:3 to
16:9.
Input A (VIDEO) button [INPUT SELECT A]
Selects the video and audio signals input to the VIDEO A
*
and AUDIO A q terminals on the rear panel. The
button lights when selected.
Input B (VIDEO Y/C) button [INPUT SELECT B]
Selects the video and audio signals input to the VIDEO B
(
or VIDEO B (Y/C) ) and AUDIO B w terminals on
the rear panel. The button lights when selected.
ASPECT
AB
INPUT SELECT
CD
SLOT
Note:
● The VIDEO B terminals include a video terminal (BNC
4
.
connector) and a Y/C terminal (mini-DIN 4-pin connector).
The Y/C (S-video) terminal has priority.
Input C/D (Slot) buttons [INPUT SELECT C/D
12
(SLOT)]
Selects the signals to be input via the input cards installed
in the rear panel card slots.
C, D: Selects the image from the input card in the slot.
For details on input connectors and using the INPUT
SELECT button, refer to page 7.
Power indicator
13
Unlit : The main power is OFF.
Orange : The main power is ON, but the monitor’s power
is OFF (in the stand-by mode).
Green : The main power is ON, and the monitor’s power
is ON (in the normal operation mode).
Power switch [POWER ]
14
Press the power switch to turn the monitor’s power ON or
OFF when the main power is ON.
Note:
● When RUSH DELAY is set to SLOW, it takes about
three seconds before power is actually supplied after
the power switch is pressed.
Speaker
15
A built-in speaker is located inside the right side panel
when the monitor is viewed from the front.
POWER
Input card slot (SLOT)
16
Optional input cards can be installed in this slot. Input
cards are not provided when you purchase this monitor.
REMOTE (external control) terminal
17
Connect this terminal to an external control unit to enable
remote operation of the monitor.
Refer to the HOW TO USE EXTERNAL CONTROL on
page 17 for more details.
Video A terminals [VIDEO A IN/OUT]
18
Video signal input (IN) and output (OUT) terminals.
The output terminal is bridge-connected.
IN : Video signal input terminal
OUT : Bridge-connected video signal output terminal
Notes:
* For corresponding audio signals, use the AUDIO A
terminals
* Also refer to BASIC CONNECTION EXAMPLE
on page 15.
Video B terminals [VIDEO B IN/OUT]
19
Video signal input (IN) and output (OUT) terminals.
The output terminal is bridge-connected.
IN : Video signal input terminal
OUT : Bridge-connected video signal output terminal
Notes:
* For corresponding audio signals, use the AUDIO B
terminals
* Also refer to BASIC CONNECTION EXAMPLE on
page 15.
Video B (Y/C) terminals [VIDEO B Y/C IN/OUT]
20
Y/C (S-video) signal input (IN) and output (OUT) terminals. The output terminal is bridge-connected.
IN:Y/C-separated (S-video) video signal input
terminal
OUT : Bridge-connected Y/C-separated (S-video) signal
output terminal.
VIDEO A
18
INOUT
VIDEO B
19
IN
AUDIO A
AUDIO B
IN
OUT
IN
IN
20
21
22
OUT
Y/C
OUT
OUT
16
SLOT
REMOTE
17
VIDEO A
IN OUT
VIDEO B
IN
OUT
IN
Y/C
OUT
AUDIO A
OUT
IN
AUDIO B
OUT
IN
Notes:
* For corresponding audio signals, use the AUDIO B
terminals
w
* When both VIDEO B terminals are connected (input) at
* Also refer to BASIC CONNECTION EXAMPLE
Audio A terminals [AUDIO A IN/OUT]
21
Input (IN) and output (OUT) terminals for the audio signal
corresponding to the VIDEO A terminals
The output terminal is bridge-connected.
IN : Audio signal input terminal
OUT : Bridge-connected audio signal output terminal
.
the same time, the Y/C terminal has priority.
on page 16.
*
.
ENGLISH
Notes:
* For corresponding video signals, use the VIDEO A
terminal
*
q
.
w
.
* Also refer to BASIC CONNECTION EXAMPLE
Audio B terminals [AUDIO B IN/OUT]
22
Input (IN) and output (OUT) terminals for the audio
signals corresponding to the VIDEO B terminals
VIDEO B (Y/C) terminals
The output terminal is bridge-connected.
IN : Audio signal input terminal
OUT : Bridge-connected audio signal output terminal
* For corresponding video signals, use the VIDEO B
* Also refer to BASIC CONNECTION EXAMPLE
.
on pages 15 and 16.
Notes:
terminals
(
or VIDEO B (Y/C) terminals ).
on pages 15 and 16.
(
)
.
or
TM-H1750CG
5
Page 4
1-4
TM-H1750CG
No.51923
CONTROLS AND FEATURES
REAR VIEW
<Rear Panel>
SLOT
To AC outlet
(120 V AC,
50 Hz/60 Hz)
To AC outlet
(230 V AC,
50 Hz/60 Hz)
For U.S.A. and Canada
For Europe
For the United Kingdom
Main power switch
23
Press the switch to turn the main power ON or OFF. When
the main power is ON, the power lamp on the front panel
lights in orange and the monitor enters the stand-by
mode.
I : ON : OFF
AC inlet [AC IN]
24
Power input connector. Connect the provided AC power
t
to an AC outlet (120 V AC or 230 V AC,
cord
50 Hz/60 Hz).
25
25
25
Power cord
25
Connects the provided power cord (120 V AC or
230 V AC, 50 Hz/60 Hz) to the AC IN connector
Caution:
In North America (USA and Canada), this monitor comes
with one power cable. In Europe and the United Kingdom, two power cables are provided (one for use in
continental European countries and the other for the UK).
Be sure to use the power cable that is appropriate for the
AC outlets used in your region. If none of the power
cables provided is suitable, please contact your dealer or
qualified service personnel to obtain the correct type of
power cable.
REMOTE
VIDEO A
IN OUT
VIDEO B
IN
OUT
IN
Y/C
OUT
AUDIO A
OUT
IN
AUDIO B
OUT
IN
2423
(cont’d)
r
.
CONTROLS AND FEATURES
(INPUT CARD: OPTIONAL)
COMPONENT/RGB INPUT CARD (OPTIONAL:
IF-C01COMG)
G/Y
OUTIN
B/PB/B-Y
R/PR/B-Y
HD/C
VD
AUDIO
OUT
IN
Compatible signal formats:
480/50i, 480/60i
1
OUTIN
OUTIN
S
OUTIN
2
OUTIN
OUTIN
4
3
SDI INPUT CARD (OPTIONAL: IF-C01SDG)
SWITCHED
OUT
IN
SDI 1
IN
SDI 2
AUDIO 1
OUT
IN
AUDIO 2
Compatible signal formats: 480/60i, 480/50i
Note:
● The optional input cards shown below cannot be used.
Using any of these cards will void your warranty and may
result in damage or malfunction.
*Video input card (IF-C01PNG)
*HD-SDI input card (IF-C01HSDG)
1
2
4
3
Video input/output terminals
1
Input (IN) and output (OUT) terminals for component
(color deference) or RGB signals.
The IN and OUT terminals are bridge-connected.
(When no cable is connected to the OUT terminal, the
input signal is automatically terminated.)
Select component signal : press INPUT SELECT C button
Select RGB signal:press INPUT SELECT D button
Synchronized signal input/output terminals
2
Input (IN) and output (OUT) terminals for the vertical,
horizontal or complex synchronized signals.
The synchronized signals from these terminals have
priority over other terminals. When no synchronized signal
is input to these terminals, the synchronized signal from
the video input/output terminals (G/Y terminals) is valid.
The IN and OUT terminals are bridge-connected.
(When no cable is connected to the OUT terminal, the
input signal is automatically terminated.)
External sync is available with RGB input only. G on
SYNC cannot be used with RGB input.
Audio input/output terminals
3
Input (IN) and output (OUT) terminals for audio signals.
The IN and OUT terminals are bridge-connected.
Connection terminal (to a Color Video Monitor)
4
Attach to the connection terminal of your color video
monitor.
Output terminal for a selected component
1
serial digital signal
Output terminal for a selected digital signal (the input
displayed on the screen). The output signal is cablecompensated.
NOTE: When the monitor’s main power is OFF, no digital
signal is output.
In the standby mode, signals from the SDI 1 connector
are output.
Input terminals for component serial digital
2
signals
Input terminals for the digital signal.
Select SDI 1 : press INPUT SELECT C button
Select SDI 2 : press INPUT SELECT D button
3
Audio input/output terminals
Input (IN) and output (OUT) terminals for the analog
signals corresponding to SDI 1 and SDI 2.
NOTE: This input card cannot decode audio data even if
contained in the input digital signal.
Connection terminal (to a Color Video
4
Monitor)
Attach to the connection terminal of your color video
monitor.
ENGLISH
6
7
Page 5
+
–
–
PREPARATION
HOW TO HANDLE BASIC
OPERATIONS
No.51923
NOTE : Do not touch the terminal connected to the monitor or board pattern.
8
1-5
INSTALLING THE INPUT CARD
1. Turn off the Color Video Monitor’s main power and unplug the power cable
from the AC outlet.
2. Unscrew the screws and remove the slot cover from the slot (on the rear side
of the monitor) in which you are going to install the card.
Rear side of the TM-H1750CG
color video monitor
SLOT
REMOTE
VIDEO A
IN OUT
VIDEO B
ININOUT
Y/C
3. Insert the Input Card’s board (green-colored) into the slot, fitting the board into
the guide rails on the top and bottom of the slot.
Fit the board to
the guide rails.
Knob
Input card (the illustration
shown is of the IF-C01COMG)
Knob
4. Push the Input Card in so that its front panel touches the monitor’s rear panel.
5. Secure the Input Card by replacing the screws removed in Procedure 2.
SLOT
REMOTE
VIDEO A
IN OUT
VIDEO B
ININOUT
Y/C
Do not remove slot covers from the monitor’s slots if they are not in use.
Slot cover
SLOT
REMOTE
VIDEO A
IN OUT
VIDEO B
ININOUT
Y/C
Guide rails
BASIC OPERATION
1. Press the main power switch to turn on the power.
2. Press the POWER switch to turn on the power.
POWER
3. Press the INPUT SELECT buttons to choose input.
AB
INPUT SELECT
ON : Power turns ON. (Power indicator: lit)
Green : The main power is ON, and the monitor ’s
OFF :Power turns OFF. (Power indicator: unlit)
Select video/audio signals input to terminals on the rear
panel. The selected button lights in green.
CD
SLOT
INPUT
SELECT
buttons
1
Input A
(VIDEO)
2
Input B
(VIDEO/Y/C)
3
Input C
4
Input D
Note: The Y/C (S-video) terminal has priority.
power is ON (in the normal operation mode).
Orange : The main power is ON, but the monitor’s
power is OFF (in the standby mode)
Unlit :The main power is OFF.
Terminals on the rear panel
Video signal inputAudio signal input
VIDEO A terminalAUDIO A terminal
VIDEO B terminal
VIDEO B (Y/C) terminal
Refer to page 7 for details about the input terminals
on each card and the INPUT SELECT button.
AUDIO B terminal
4. Press the VOLUME/SELECT buttons to adjust the
speaker volume.
VOLUME/SELECT
Press this button to display the speaker volume level on the
screen.
+ : The Built-in speaker volume is increased. (00 = 50)
– : The Built-in speaker volume is decreased. (50 = 00)
* Screen indication will disappear about 10 seconds after operating.
* The on-screen display goes off when you press MENU button.
PICTURE ADJUSTMENT
1. Press select buttons corresponding to the item
you want to adjust.
CHROMA
CONTRAST
PHASE BRIGHT
2. Adjust with the VOLUME/SELECT buttons.
VOLUME/SELECT
The item you select is displayed on the screen.
1
Chorma control : Press the CHROMA/PHASE button once.
2
Phase control : Press the CHROMA/PHASE button twice.
3
Contrast control : Press the CONTRAST/BRIGHT button once.
4
Brightness control: Press the CONTRAST/BRIGHT button twice.
*Pressing the CHROMA/PHASE button and CONTRAST/BRIGHT button
alternately while the item is shown on screen restores the previous status.
When no item is shown on screen, CHROMA and CONTRAST have priority.
VOLUME/SELECT button
Items
CHROMA
(Chroma)
PHASE
(Phase)
CONTRAST
(Contrast)
BRIGHT
(Brightness)
*Screen indication will disappear about 10 seconds after operating.
*The on-screen display goes off when you press MENU button.
–+
lighterdeeper
reddishgreenish
lowerhigher
darkerbrighter
STATUS indication
(PAL or NTSC)
PAL
About the STATUS indication
● With the COLOR SYSTEM setting set
to AUTO mode, when you turn on the
power or select inputs, the color
system indication appears for about
3 seconds on the screen while PAL or
NTSC signals are being detected.
It does not appear when receiving a
B/W signal or when no signal is input.
Refer to page 11 for more information
about COLOR SYSTEM setting and
page 12 for more information about
STATUS indication setting.
00 ~ 50
VOLUME : 20
UPPER
PHASE : 00
PHASE : 00
–40 ~ +40
+
Notes:
● Phase control is effective only in the
NTSC color system mode.
● Chroma control is not effective when
receiving RGB and B/W or when no
signal is input. (Except when a
component signal is input.)
● When CHROMA is adjusted to “–40,”
the picture becomes less colorful.
● “NO EFFECT” is displayed (for about
3 seconds) when your selected
function has no effect.
● To change the display position on
screen, set UPPER or LOWER with
ADJ. BAR POSI.
LOWER
ENGLISH
TM-H1750CG
9
Page 6
1-6
TM-H1750CG
No.51923
HOW TO HANDLE BASIC
OPERATIONS
VIDEO SIGNAL CONTROLS
Use these buttons for video signal control.
UNDER SCAN
Press the UNDER SCAN button to reduce the size of display area so that the whole
picture is displayed on screen. Use to check the picture frame.
COLOR OFF
To display a black and white picture, press the COLOR OFF button to input the luminance signal only. Use to check noise in the luminance signal or for white balance
adjustment.
Note:
● No effect with RGB input.
BLUE CHECK
Input the standard color-bar signal for your TV system and display it on the screen.
When the BLUE CHECK button is pressed, the red and green signals are cut and only
the blue signal is displayed. The BLUE CHECK function adjusts and checks CHROMA
(COLOR) GAIN and PHASE.
Make sure that COMPO. LEVEL has been initialized when a component signal is input.
[Procedure]
1. Input the standard color-bar signal for your TV system and display it on the screen.
2. Press the BLUE CHECK button.
3. Press the CHROMA button to adjust the chroma so that the blue bars on the left and
right sides of the screen have the same brightness.
4. (Only when an NTSC signal is input) Press the PHASE button to adjust the phase so
that the two blue bars at the center of the screen have the same brightness.
5. (Only when an NTSC signal is input) Repeat procedures 3 and 4 for the adjustment so
that all four blue bars on the screen have the same brightness.
When you have finished making the adjustment, press the BLUE CHECK button to
deactivate.
Initializing COMPO. LEVEL (when a component signal is input)
with the IF-C01COMG component/RGB input card inserted
When a component signal is input, be sure to adjust (initialize) the COLOR offset in
COMPO. LEVEL.
[Procedure]
1. Input the standard color-bar signal for your TV system and display it on the screen.
2. Press the BLUE CHECK button.
3. Select COMPO. LEVEL in the <MENU> screen and then adjust it with VOLUME +/–
buttons so that the blue bars on the left and right sides of the screen have the same
brightness.
4. Quit the <MENU> screen and press the BLUE CHECK button.
5. Make sure that the blue bars on the left and right sides of the screen have the same
brightness.
6. Repeat procedures 3, 4 and 5 for the adjustment so that the blue bars on the left and
right sides of the screen have the same brightness.
(cont’d)
Blue
Blue
Blue
Blue
Blue
Blue
Blue
Blue
HOW TO USE THE MENU FUNCTIONS
DISPLAY AND SELECTION IN THE <MENU>
SCREEN MODE (SETTING)
You can set the following menu items.
Set them depending on your needs.
• APERTURE• COLOR SYSTEM
• ADJ. BAR POSI.• COMPO. LEVEL*
• COLOR TEMP.• RUSH DELAY
1. Press the MENU button.
MENU
The <MENU> screen is displayed.
* The on-screen display goes off automatically after about five
minutes with operation performed.
2. Press the CHROMA/PHASE or CONTRAST/BRIGHT
button to select MENU items.
CHROMA
CONTRAST
PHASE BRIGHT
APERTURE
ADJ. BAR POSI.
COLOR TEMP.
COLOR SYSTEM
COMPO. LEVEL*
RUSH DELAY
A selection mark (4) is put next to the selected item.
Front panelFunction
buttondisplayed
CHROMA/
PHASE
CONTRAST/
BRIGHT
Forward selection mark (
Reverse selection mark (
Contents
4
4
3. Press the VOLUME/SELECT buttons to set.
VOLUME/SELECT
Menu itemsPurpose Setting range
APERTUREPicture aperture level
ADJ.BAR POSIVolume bar position
COLOR TEMP.Color temperature of white
COLOR SYSTEMColor system
COMPO. LEVEL*Component level
RUSH DELAYDelay time
*For normal use, leave the COLOR SYSTEM setting to AUTO.
If reception is unsatisfactory in AUTO position, set it to the appropriate color system mode (NTSC or PAL).
*COMPO. LEVEL is displayed only with COMPONENT (SDI) input. (Shown with INPUT-C and INPUT-D
except for RGB input.)
Front panelFunction
buttondisplayed
VOLUME/
SELECT (+)
VOLUME/
SELECT (–)
balance
+Increase (to max. value)
4
Forward the setting value
–Decrease (to min. value)
1
Reverse the setting value
00 +01 +39 +40
LOWER UPPER
6500 9300
AUTO NTSC AUTO PAL
–40 –39 –01 00 +1 +9 +10
STD. SLOW
Contents
• • • • • • • • • • • •
• • • •
4. If you want to set the other menu items, repeat
procedures 2 and 3.
5. Press the MENU button to quit.
MENU
Front panelFunction
buttondisplayed
MENUEXIT
Quit (or Release) the <MENU>
screen
Contents
<MENU> screen
1
2
CHROMAMENU
PHASE BRIGHT
1
Selection mark (4): Indicates the
menu item you select.
2
)
)
Menu item: Menu items you can
select.
3
Setting display: Indicates the current
settings (value).
4
Function display: The functions of
the front panel buttons (5 buttons on
the left) correspond to the function
displayed.
Function
displayed
EXIT Exits the <MENU> screen.
<ADJ. BAR POSI> screen
CHROMAMENU
PHASE BRIGHT
The upper screen; when setting
“UPPER” in “ADJ. BAR POSI.”
The lower screen; when setting
“LOWER” in “ADJ. BAR POSI.”
<MENU >
‰ APERTURE: 00
ADJ. BAR POSI.:
COLOR TEMP.: 6500
COLOR SYSTEM: AUTO
COMP. LEVEL: 00
RUSH DELAY: STD
CONTRAST VOLUME/SELECT
<Front panel buttons>
Forward the menu item.
Reverse the menu item.
–Lower the adjustment
value. (to the minimum)
+Raise the adjustment
value. (to the maximum)
4
Forward the setting value.
1
Reverse the setting value.
BRIGHT : 00
BRIGHT : 00
CONTRAST VOLUME/SELECT
<Front panel buttons>
LOWER
EXIT
Contents
EXIT
UPPER
3
4
ENGLISH
LOWER
10
11
Page 7
HOW TO USE THE MENU
FUNCTIONS
(cont’d)
No.51923
DISPLAY AND SELECTIONS IN THE <SET-UP
MENU> MODE (SETTING)
You can set the following set-up menu items.
• PICTURE SUB ADJ.• WHITE BALANCE• REMOTE SYSTEM
• H. POSITION• CONTROL LOCK• INPUT REMOTE
• V. POSITION• STATUS DISPLAY
Notes:
● Parameters for H. POSITION and V. POSITION can be set separately depending on
the signal (Input A (VIDEO), Input B (VIDEO), Input C or Input D) selected with the
input select buttons on the front panel.
Select the required video input with the input select buttons on the front panel in
advance.
● WHITE BALANCE can be set independently at 6500 or 9300 for the color temperature
value.
Set COLOR TEMP. to 6500 or 9300 on the <MENU> screen beforehand.
● INPUT REMOTE is shown when REMOTE SYSTEM is set to MAKE.
1. While pressing the MENU button, press the
CHROMA/PHASE button.
MENU
CHROMA
PHASE
The <SET-UP MENU> screen is displayed.
* The on-screen display goes off automatically after about five
minutes with operation performed.
2. Press the CHROMA/PHASE or CONTRAST/BRIGHT
button to select the desired menu item.
CHROMA
CONTRAST
PHASE BRIGHT
PICTURE SUB ADJ.
H. POSITION
V. POSITION
WHITE BALANCE
CONTROL LOCK
STATUS DISPLAY
REMOTE SYSTEM
INPUT REMOTE
A selection mark (4) is put next to the selected item.
Front panelFunction
buttondisplayed
CHROMA/
PHASE
CONTRAST/
BRIGHT
Contents
Forward selection mark (4)
Reverse selection mark (4)
3. Press the VOLUME/SELECT buttons to set.
VOLUME/SELECT
Front panelFunction
buttondisplayed
VOLUME/
SELECT (+)
VOLUME/
SELECT (–)
+Increase (to max. value)
4
CUTOSelects CUT OFF setting screen
–Decrease (to min. value)
1
DRVSelects DRIVE setting screen
Contents
Forward the setting value
Reverse the setting value
Notes:
● For WHITE BALANCE items, select the CUT OFF or DRIVE
setting screen, then select the function display for adjustment.
● Press the EXIT (MENU) button to return to the <SET-UP
MENU> screen.
<SET-UP MENU> screen
1
2
<SET-UP MENU>
‰ PICTURE SUB ADJ.
H. POSITION: 00
V. POSITION: 00
WHITE BALANCE
CONTROL LOCK: OFF
STATUS DISPLAY : ON
REMOTE SYSTEM : MAKE
INPUT REMOTE: A – D
EXIT
CHROMAMENU
CONTRAST VOLUME/SELECT
PHASE BRIGHT
<Front panel buttons>
1
Selection mark (4): Indicates the
menu item you select.
2
Menu item: Menu items you can
select.
3
Setting display: Indicates the
current settings (value).
4
Function display: The functions of
the front panel buttons (5 buttons
on the left) correspond to the
function displayed.
Function
displayed
–Lower the adjustment
+Raise the adjustment
4
1
EXIT
DRV Selects DRIVE adjustment.
CUTO
RB
RGB
DISP function is effective only
Contents
Forward the menu item.
Reverse the menu item.
value. (to the minimum)
value. (to the maximum)
Forward the setting value.
Reverse the setting value.
Exit the <MENU>
screen.
Selects CUT OFF
adjustment.
Adjusts red and blue
signal level.
Adjusts red, green and
blue signal level.
Turns the ON-SCREEN
display on or off. (This
in the DRIVE or CUT OFF
adjustment mode.)
Set-up menu itemsPurposeSettings
PICTURE SUB ADJ.Image sub adjustmentSelects CONTRAST/BRIGHT/CHROMA/PHASE. The
CONTRAST Adjusts contrast.
BRIGHTAdjusts brightness.
CHROMAAdjusts color density.*1
PHASEAdjusts hue.*1
H. POSITIONAdjusts the horizontal position of the
3
4
V. POSITIONAdjusts the vertical position of the screen
WHITE BALANCEAdjusts the white balance.Selects the drive (DRV) or cut off (CUTO) adjustment. The selected
DRIVE R. DRIVEAdjusts red level.
B. DRIVEAdjusts blue level.
CUT OFF R. CUT OFF Adjusts red cut off.
G. CUT OFF Adjusts green cut off.
B. CUT OFF Adjusts blue cut off.
CONTROL LOCKSets the operation buttons on the front
STATUS DISPLAYSets the status display of the color system.
REMOTE SYSTEMSets the external control function method.*2
INPUT REMOTESets external control of input selection.
*1 May not be shown depending on the type of signals input.
*2 Refer to HOW TO USE EXTERNAL CONTROL on page 17 for more details.
screen (+: Horizontal position shifts
to the right/-: Horizontal position shifts to
the left)
(+: Vertical position moves up/-: Vertical
position moves down)
panel to control lock mode.
(Shown only when REMOTE SYSTEM is *2
set to MAKE.)
4. To set the other set-up menu items, repeat the
procedures 2 and 3.
5. Press the MENU button to quit.
MENU
Note:
SettingDescription
MAKEMake contact system: Controls the function with H and L (short-
TRG.Trigger system: Controls the function by short-circuiting (short-
A-DSwitches the input by short-circuiting a specified signal line in
A/BSwitches between INPUT A and INPUT B with D-sub pin 2.
(Also, refer to HOW TO USE EXTERNAL CONTROL on page 17.)
Front panel Function
buttondisplayed
MENUEXIT
circuits or opens 15th terminal (GND)).
circuits or opens 15th terminal (GND)) with pulse (about 1 sec.)
INPUT A, B, C, or D.
selected setting screen is shown. Select the function display for
adjustment.
–
10 –9 –01 00 +01 +09 +10
• •
–
10 –9 –01 00 +01 +09 +10
• •
–
10 –9 –01 00 +01 +09 +10
• •
–
10 –9 –01 00 +01 +09 +10
• •
–
5 • • • –01 00 +1 • • • +5
–
5 • • • –01 00 +1 • • • +5
setting screen is shown. Select the function display for adjustment.
–
20 –19 –01 00 +01 +19 +20
• •
–
20 –19 –01 00 +01 +19 +20
• •
–
20 –19 –01 00 +01 +19 +20
• •
–
20 –19 –01 00 +01 +19 +20
• •
–
20 –19 –01 00 +01 +19 +20
••
OFF
ON
OFF
ON
MAKE
TRG.
A–D
A/B
Contents
Quit (or Release) the <MENU>
screen
• •
• •
• •
• •
Notes:
● When the CONTROL LOCK function is
set to ON, pressing operation buttons
on the front panel will display the
message “CONTROL LOCK ON!” on
the screen for about 3 seconds.
● The CONTROL LOCK function is
maintained even when the power is
turned off.
● To turn off the CONTROL LOCK
function, while holding the MENU button
press the CHROMA/PHASE button.
Then set the CONTROL LOCK function
to OFF.
● Even when the CONTROL LOCK
function is set to ON, the following
operations are available:
– Power Switch operation
– Volume control with the VOLUME/
SELECT buttons
– Display or disappear of the <SET-UP
MENU> screen.
● The STATUS DISPLAY function can be
set to display (ON) or not display (OFF)
the present color system when the
power is turned on or the input signal is
changed. Refer to page 9 for more
information.
● When REMOTE SYSTEM is set to
MAKE and any one of the INPUT A to D
buttons, the UNDER SCAN button,
COLOR OFF button or the ASPECT
button is pressed, “REMOTE ON!”
appears on screen for about 3 seconds.
(Not shown with CONTROL LOCK set
to ON.)
● When REMOTE SYSTEM is set to
TRG, the front panel controls can be
operated.
● INPUT REMOTE and REMOTE
SYSTEM are enabled when REMOTE
ENABLE is set to ON.
• •
• •
• •
• •
• •
ENGLISH
TM-H1750CG
1-7
12
13
Page 8
1-8
TM-H1750CG
SCREEN DISPLAY AND SELECTIONS IN THE
<SET-UP MENU> RESET MODE
No.51923
HOW TO INITIALIZE THE
SETTING
You can set <MENU> and <SET-UP MENU> screen items, picture adjustment items and
the volume level to their factory-set (initial) values.
1. Press the Power ( ) switch to turn the power
OFF (activate the standby mode).
POWER
2. While pressing both MENU button and CHROMA/
PHASE button, press the Power (
the power ON.
The <SET-UP MENU> RESET screen is displayed.
CHROMA
PHASE
MENU
* The screen automatically disappears when no operation
POWER
is performed after about 5 minutes.
Note:
● The <SET-UP MENU> RESET screen will not be
displayed if the MENU or CHROMA/PHASE buttons are
pressed for a very short time. Keep pressing them until
the display screen appears.
3. Setting
Initialization is required.
VOLUME/SELECT
Initialization is not required.
MENU
Press the VOLUME/SELECT [+] button.
* Initialization is completed, and the <SET-UP MENU>
RESET screen disappears.
Press the MENU button.
* Initialization is aborted, and the <SET-UP MENU>
RESET screen disappears.
) switch to turn
<SET-UP MENU> RESET screen
<SET–UP MENU> RESET
Are you sure ?
“Yes” then <+>
“No” then <MENU>
Initial settings
Functions (Items)
Sorts
APERTURE00
ADJ. BAR POSI LOWER
COLOR TEMP6500
COLOR SYSTEM
COMPO. LEVEL 00
<MENU> screen
RUSH DELAYSTD
PICTURE SUB ADJ.
CONTRAST 00
BRIGHT00
CHROMA00
PHASE00
H. POSITION00
V. POSITION00
WHITE BALANCE
R. CUT OFF 00
G. CUT OFF 00
B. CUT OFF 00
R. DRIVE00
B. DRIVE00
<SET-UP MENU> screen
CONTROL LOCK OFF
STATUS DISPLAY ON
REMOTE SYSTEM MAKE
INPUT REMOTE A – D
CHROMA00
PHASE00
CONTRAST00
BRIGHT00
Picture adjustment
VOLUME 20
Volume
Initialization
(setting)
AUTO
BASIC CONNECTION EXAMPLE
Notes:
•
Before connecting your system, make sure that all units are turned off.
•
The illustration below shows some examples of different connections. Terminal connections may differ depending on the component connected.
Be sure to refer to the instructions provided with the unit(s) you are connecting.
•
Each pair of input (IN) and output (OUT) terminals are bridge-connected.
•
If you’re not connecting any equipment to a bridged output (OUT) terminal, be sure not to connect any other cables to the bridged output (OUT)
terminal as this will cause the terminating resistance switch to open (auto terminate function).
•
When making a bridge connection, connect the input (IN) and output (OUT) terminals on the monitor to separate video components.
(For example, if both terminals are connected to the same VCR, resonance may occur except during playback. This is caused by the same video
signal “looping” between the VCRs, and is not a malfunction.)
•
Select the video input signal (INPUT A(VIDEO) or INPUT B (VIDEO/Y/C)) with the INPUT SELECT buttons on the front panel. When both
VIDEO B terminals are connected (input) at the same time, the Y/C terminal has priority.
VIDEO A Connection Example (Select Input A (VIDEO))
Video
Video Camera
Video Monitor
VCR
VIDEO B (VIDEO) Connection
Example (Select Input B (VIDEO))
Video Camera
Video Monitor
VCR
(Video signal cable)
Audio
(Audio signal cable)
Video
(Video signal cable)
Audio
(Audio signal cable)
VIDEO A
INOUT
VIDEO B
IN
IN
OUT
AUDIO A
IN
AUDIO B
IN
OUT
Y/C
OUT
OUT
Video
(Video signal cable)
Video
(Video signal cable)
Audio
(Audio signal cable)
Audio
(Audio signal
cable)
Video Monitor
VCR
Video Monitor
: Signal Flow
ENGLISH
14
15
Page 9
BASIC CONNECTION EXAMPLE
(cont’d)
HOW TO USE EXTERNAL
CONTROL
No.51923
VIDEO B (Y/C) Connection Example (Select Input B (Y/C))
VIDEO A
INOUT
Video Camera
Video Monitor
VCR
Y/C (S-video)
(Y/C (S-video) signal cable)
Audio
(Audio signal cable)
VIDEO B
AUDIO A
AUDIO B
IN
IN
OUT
IN
IN
OUT
Y/C
OUT
OUT
Y/C (S-video)
(Y/C (S-video) signal cable)
Audio
(Audio signal cable)
VCR
Video Monitor
: Signal Flow
ABOUT EXTERNAL CONTROL
This monitor is provided with an external control terminal. MAKE (make contact) or TRG. (trigger) system can be selected.
(MAKE (make contact system): The function is controlled with H and L (short-circuit/open with the 15th pin GND).
(TRG. (trigger system): The function is controlled by short-circuiting with pulses (for about 1 second) (short-circuit/open with the
15th pin GND).
* The 14th pin (REMOTE ENABLE) is controlled with MAKE even though TRG. is selected.
Note:
● When this monitor is externally controlled, the following buttons are disabled.
MAKE: INPUT-A to D, UNDER SCAN, COLOR OFF, ASPECT on the front panel.
Connections
Connect (short-circuit) the 15th terminal (GND) to each of the 1st through 14th terminals in the
3-lines 15-pins D-sub connector. The functions of each terminal are listed below.
10
15
14
13
12
11
The Names and Functions of Terminals
No. NamesFunctionsOperations (OFF p[ ON)*1
1 TALLYPuts on the tally lamp.Put offPut on
2 INPUT AChanges the input to INPUT ANot changeChange*2*8
3 INPUT BChanges the input to INPUT BNot changeChange*3*8
4 INPUT CChanges the input to INPUT CNot changeChange*4*8
5 INPUT DChanges the input to INPUT DNot changeChange*5*8
6 not used–––*6
7 not used–––*6
8 COLOR OFFChanges the picture black-and-white. Not changeChange
9 not used–––*6
10 ASPECTChanges the screen ratio to 16:94:316:9
11 UNDER SCANMakes the screen under-scanOver-scanUnder-scan
12 not used–––*6
13 not used–––*6
14 REMOTE ENABLE Makes the external control from the InvalidValid*7
15 GNDUsed as a ground terminal––
*1: OFF stands for disconnection, and ON stands for short-circuit.
*2: When INPUT REMOTE in the set-up menu is set to A/B, H: INPUT A and L: INPUT B are set.
*3: When INPUT REMOTE in the set-up menu is set to A/B, pins not used should not be connected.
*4: When INPUT REMOTE in the set-up menu is set to A/B, pins not used should not be connected.
*5: When INPUT REMOTE in the set-up menu is set to A/B, pins not used should not be connected.
*6: Do not connect.
*7: Setting REMOTE ENABLE to ON enables remote control from the REMOTE terminal.
*8: INPUT REMOTE setting in the set-up menu (REMOTE SYSTEM shown only when MAKE is selected.)
For the D-sub pins 2, 3, 4 and 5, 4-pin or 1-pin control can be set with INPUT REMOTE in the set-up menu.
•4-pin control: Switches input by short-circuiting a specified signal line in INPUT A to D.
•1-pin control: Switches between INPUT-A and INPUT-B only with the 2nd pin of the D-sub connector. In this case, INPUT-C and INPUT-D
cannot be selected.
Open (H): INPUT-A
Short-circuit (L): INPUT-B
NOTE : When more than two terminals are selected (short-circuited) from INPUT A through INPUT D, signal input is prioritized
alphabetically (A, B, C, D).
To control INPUT A through INPUT D, we recommend using the interlock switch, which turns off a switch when another
switch is turned on.
REMOTE terminal valid or invalid
9
5
4
8
3
7
2
6
1
ENGLISH
1-9
16
TM-H1750CG
17
Page 10
1-10
No.51923
TROUBLESHOOTING
Solutions to common problems related to your monitor are described here. If none of the solutions presented here
solves the problem, unplug the monitor and consult a JVC-authorized dealer or service center for assistance.
Problems
No power supply.
No picture with the
power on.
No sound.
Shaking picture.
No colors, wrong
color, or dark picture.
Unnatural, irregularly
colored, or distorted
picture.
Dark stripes appear
at the top and bottom
of the screen, picture
vertically squeezed.
The overall picture
size is too small.
Function buttons on
the front panel do not
function.
The INPUT SELECT
buttons do not
function.
Is the power plug loosened or disconnected?
Is the main power turned OFF?
Is the video signal output from the connected
component?
Is the input signal selected properly?
Is the video cable disconnected?
Is the audio signal output from the connected
component?
Is the volume output set to minimum?
Is the audio cable disconnected?
Is the monitor close to a device generating a
strong magnetic field?
Is the color system selected properly?
Has the picture control setting (CONTRAST,
BRIGHT, CHROMA or PHASE) been changed?
Is the monitor close to a speaker, magnet or any
other device generating a strong magnetic field?
Is the aspect ratio set to 16:9?
Has the UNDER SCAN button been pressed so
the UNDER SCAN button lights?
Has control of the buttons been locked? (Has
the CONTROL LOCK function been set to ON?)
Is input selection under external control? (Has
the REMOTE ENABLE function been set to
valid?)
Points to be checked
Firmly insert the power plug.
Turn the main power ON. (See page 6.)
Set the connected component correctly.
Select the required video signal input with the
Input select button. (See page 9.)
Connect the video signal cable firmly.
(See pages 15 and 16.)
Set the connected component correctly.
Adjust the speaker volume with the VOLUME/
SELECT button. (See page 9.)
Connect the audio signal cable firmly.
(See pags 15 and 16.)
Move the device away from the monitor until the
picture stabilizes.
Set COLOR SYSTEM in the <MENU> screen to
AUTO. (See page 11.)
Set each picture control to the standard setting.
(See page 9.)
Press the COLOR OFF button and BLUE CHECK
button to adjust. (See page 10.)
Move the device away from the monitor and turn
the monitor’s power off. Wait at least 30 minutes,
then turn the power on again.
Switch the aspect ratio to 4:3 with the ASPECT
button on the front panel.
Press the UNDER SCAN button to turn off the
button. (See page 4.)
Set CONTROL LOCK in the <SET-UP MENU>
screen to OFF. (See pages 12 and 13.)
Set REMOTE SYSTEM in the <SET-UP MENU>
screen to TRG. (See pages 12 and 13.)
Set REMOTE ENABLE to OFF (invalid).
(See page 17.)
Measures (Remedy)
TM-H1750CG
The following are not malfunctions:
● When a bright still image (such as a white cloth) is displayed for a long period, it may appear to be colored. This is due to the
structure of the cathode ray tube and will be deleted when another image is displayed.
● You experience a mild electric shock when you touch the picture tube. This phenomenon is due to a normal buildup of static
electricity on the CRT and is not harmful.
● The monitor emits a strange sound when the room temperature changes suddenly. This is only a problem if an abnormality
appears on the screen as well.
● If two or more monitors are operated next to each other, their images may shake or be distorted. This phenomenon is due to
mutual interference; it is not a malfunction. Move the monitors away from each other until the interference disappears or turn
the power off on any monitor that is not being used.
18
Page 11
SPECIFICATIONS
TM-H1750CG
Type: Color video monitor
Color system: PAL, NTSC (3.58)
Picture tube: 16-3/16" (41 cm) measured
Audio power output: 1 W (monaural)
Built-in speaker: 8 cm round x 1
impedance of 8 Ω
Environmental
conditions: Operation temperature:
0°C – 40°C (32°F – 104°F)
Operation humidity:
20 % – 80 % (non-condensing)
Power requirements: 120 V/230 V AC, 50 Hz/ 60 Hz
Power consumption: 1.2 A (120 V AC)/0.8 A (230 V
AC)
Dimensions: Width15-5/8" (395 mm)
Height13-1/4" (334 mm)
Depth16-1/2" (418.1 mm)
Weight: 44.3 lbs (20.1 kg)
Accessory: AC power cord
ENGLISH
* Illustrations used in this manual are for explanatory purposes only. The appearance of the actual product may differ slightly.
* Dimensions and weight are approximate.
* E. & O. E. Design and specifications subject to change without notice.
No.51923
19
1-11
Page 12
TM-H1750CG
Dimensions
Unit : inch (mm)
< Front View >
15-5/8 (395)
12-7/8 (327.5)
*
*
9-5/8 (246.2)
UNDER
COLOR
CONTRAST VOLUME/SELECT
CHROMAMENU
BRIGHT
PHASE
TM-H1750CG
* Asterisks (*) are used to indicate front panel
dimensions.
BLUE
SCAN
OFF
CHECK
11-3/8 (288)
ASPECT
AB
POWER
CD
SLOT
INPUT SELECT
ø7/8 (20)
13-1/4 (334)
7 (175)
Y/C (Mini DIN 4 pin) terminal
specification
< Side View >
1/16
(1.5)
2-3/4 (68)
1/8 (3)
16-1/8 (407)
11-3/8 (286)
16-1/2 (418.1)
1/8 (3)
OUT
2
IN
1
2
1
4
3
4
3
Pin No. Signal
1GND (Y)
Y/C
2GND (C)
3Y
4C
APPENDIX:CONNECTION EXAMPLES FOR THE
SDI INPUT CARD
● To use the SWITCHED OUT terminal, the main power must be ON. (Unlike a bridged output, this connector outputs relocked
digital signals.)
● Signals output from the SWITCHED OUT terminal can be selected with INPUT-C (SDI-1) and INPUT-D (SDI-2) buttons on the
front panel (or remote control).
● When INPUT-A or INPUT-B is selected, this terminal outputs the signals last selected. In the standby mode, signals from the
SDI 1 connector are output.
1-12
20
No.51923
82
,2!#
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.