STANDARD CIRCUIT DIAGRAM
NOTE ON USING CIRCUIT DIAGRAMS
1.SAFETY
The components identified by the symbol and shading are
critical for safety. For continued safety replace safety critical
components only with manufactures recommended parts.
2.SPECIFIED VOLTAGE AND WAVEFORM VALUES
The voltage and waveform values have been measured under the
foll owing condition s.
(1)Input signal : Colour bar signal
(2)Setting positions of
each knob/button and
variable resistor
(3)Internal resistance of tester
:DC 20k
/V
(4)Oscilloscope sweeping tim e
:H
20µS/div
:V
5mS/div
:Others
Sweeping time is
specified
(5)Voltage values
:All DC voltage values
Sin ce the vol tage values of si gnal circuit vary to some exten t
according to adjustments, use them as reference values.
3.INDICATION OF PARTS SYMBOL [EXAMPLE]
In the PW board
:R1209
R209
4.INDICATIONS ON THE CIRCUIT DIAGRAM
(1)Resistors
Resistance value
No unit :[
]
K
:[K
]
M
Rated allowable power
No indication :1/ 16 [W]
Others :As specified
Ty pe
No indication
:Carbon resistor
OM R
:Oxi de metal fi lm resistor
MFR
:Met al film resi st or
MPR
:Metal plate resistor
UNFR
:Uninflammable resistor
FR
:Fusible resistor
Compos iti on resist or 1/2 [W] is spec ified a s 1/2S or Comp.
(2)Capacitors
: Original setting position
when shipped
5.NOTE FOR REPAIRING SERVICE
This model's power circuit is par tly different in the GND. The
difference of the GND is shown by the LIVE : ( ) side GND and the
ISOLATED(NEUTRAL) : ( ) side GND.Therefore, care must be
taken for the following points.
(1)Do not touch the LIVE side GND or the LIVE side GND and the
ISOLATED(NEUTRAL) side GND simultaneously. If the above
caution is not respected, an electric shock may be caused.
Therefore, make sure that the power cord is surely removed from
the receptacle when, for example, the chassis is pulled out.
(2)Do not short between the LIVE side GND and ISOLATED(NEUTRAL)
side GND or never measure with a measuring apparatus measure
with a measuring apparatus ( oscilloscope, etc.) the LIVE side GND
and ISOLATED(NEUTRAL) side GND at the same time.
If the above precaution is not respected , a fuse or any parts will be broken.
Since the circuit diagram is a standard one, the circuit and
circuit constants may be subject to change for improvement
withou t any n otice.
NOTE
Due improvement in performance, some part numbers show
in th e circuit diagram may not agree with th ose indi cate d in
the par t li st.
When ordering parts, please use the numbers that appear
in the Parts List .
Ty pe
MM
:Metalized mylar capacitor
PP
:Polypropylene capacitor
MPP
:Metalized polypropylene capacitor
MF
:Metalized film capacitor
TF
:Thin film capacitor
BP
:Bipolar electrolytic capacitor
TAN
:Tantalum capacit or
(3) Co i ls
No unit
:[
µ
H]
Others
:As specified
(4)Power Supply
:B1
:9V
:7V
Respective voltage values are indicated
(5)Test point
:Test p oint
:Only test point display
(6)Con nectin g me th od
:Connector
:Wrapping or soldering
:Receptacle
(7)Ground symbol
:LIVE side ground
:ISOLATED(NEUTRAL) side ground
:EARTH ground
:DIGITAL ground
:[M ]
Capacita nce value
1 or higher :[pF]
less than 1
:[µF]
Withstand voltage
No indicatio n :DC50[V]
Others :DC withstand voltage [V]
AC indicated
:AC withstand voltage [V]
Electr olyt ic Capacitors
47/50[Example]:Capacitance value [µF]/withstand voltage[V]
No indication
:Ceramic capacitor
:B2 (12V)
TM-H1700/U, TM-H1700
/E
SIGNAL INPUT PWB CIRCUIT DIAGRAM
MAIN & SUB DEF PWB CIRCUIT DIAGRAM
MAIN & FRONT CONTROL PWB CIRCUIT DIAGRAM
CRT SOCKET PWB CIRCUIT DIAGRAM
MAIN PWB PATTERN
SIGNAL INPUT PWB PATTERN
CRT SOCKET PWB PATTERN
SUB DEF PWB PATTERN
FRONT CONTROL PWB PATTERN
Jan. 2002 No. 51922