JVC TM-A13SU, TM-A13SU-W, TM-A13UCV User Manual

COLOR VIDEO MONIT OR

TM-A13SU TM-A13UCV TM-A13SU-W

INSTRUCTIONS

For Customer Use:

Enter below the Model No. and Serial No. which is located on the rear of the cabinet. Retain this information for future reference.

Model No. : Serial No. :

PHASE CHROMA BRIGHT CONTRAST MENU

(TM-A13SU shown)

–+

VOLUME/SELECT

B A

INPUT SELECT

ON OFF

POWER

TM-A13SU

Thank you for purchasing this JVC color video monitor. Before using it, read and follow all instructions carefully to take full advantage of the monitor's capabilities.

SAFETY PRECAUTIONS

WARNING :

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS MONITOR TO RAIN OR MOISTURE.

CAUTION :

To reduce the risk of electric shock, do not remove cover. Refer servicing to qualified service personnel.

This monitor is equipped with a 3-blade grounding-type plug to satisfy FCC rule. If you are unable to insert the plug into the outlet, contact your electrician.

FCC INFORMATION (U.S.A. only)

CAUTION: Changes or modification not approved by

JVC could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and

receiver.

– Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV

technician for help.

■ PRECAUTIONS

● Use only the power source specified on the unit.

(120 V AC, 50/60 Hz)

● Keep flammable material, water, and metal objects away from the unit – especially the interior of the unit.

● This unit incorporates high voltage circuitry. For your own safety and that of your equipment, do not attempt to modify or disassemble this monitor. There are no user-serviceable parts inside.

● Unplug the monitor when you’re not going to be using it for a long period.

■ HANDLING

● Avoid shocks or vibrations. These may damage the unit and cause it to malfunction.

● Do not block the ventilation slots.

● Do not expose this unit to high temperatures.

Extended exposure to direct sunlight or a heater could deform the cabinet or cause the performance of internal components to deteriorate.

● Do not place the unit near appliances generating strong electric or magnetic fields. There can generate picture noise and instability.

● Keep the monitor clean by wiping the cabinet and CRT screen with a piece of soft cloth. Do not apply thinner or benzine. These chemicals can damage the finish and erase printed letters. When the unit is excessively dirty, use a diluted neutral cleanser, then wipe away the cleanser with a dry cloth.

SCREEN BURN

● It is not recommended to keep a certain still image displayed on screen for a long time as well as displaying extremely bright images on screen. This may cause a burning (sticking) phenomenon on the screen of cathode-ray tube. This problem does not occur as far as displaying normal video playback motion images.

CONTENTS

SAFETY PRECAUTIONS .......................................................................................... 2

CONTROLS AND FEATURES................................................................................... 4

HOW TO HANDLE BASIC OPERATIONS ................................................................ 6

HOW TO USE THE MENU FUNCTIONS................................................................... 7

HOW TO INITIALIZE THE SETTING ....................................................................... 10

BASIC CONNECTION EXAMPLE ............................................................................11

TROUBLESHOOTING ............................................................................................. 12

SPECIFICATIONS.................................................................................................... 13

CONTROLS AND FEATURES

FRONT VIEW

[TM-A13SU / TM-A13SU-W]

PHASE CHROMA BRIGHT CONTRAST MENU

[TM-A13UCV]

–+

B A

_ON —OFF

PHASE CHROMA BRIGHT CONTRAST MENU

(Front view of TM-A13SU shown)

INPUT SELECT

VOLUME/SELECT

POWER

TM-A14PN

PHASE CHROMA BRIGHT CONTRAST MENU

1 Phase button [PHASE ]

Press this button to set the picture hue adjustment mode. Adjust the value with the VOLUME/SELECT 6 or the SELECT 7 buttons. Also used as a control button in the menu function mode.

2 Chroma button [CHROMA ]

Press this button to set the picture color density adjustment mode. Adjust the value with the VOLUME/SELECT

6 or the SELECT 7 buttons. Also used as a control

button in the menu function mode.

3 Brightness button [BRIGHT ]

Press this button to adjust picture brightness. Adjust the value with the VOLUME/SELECT 6 or the SELECT

7 buttons. Also used as a control button in the menu

function mode.

4 Contrast button [CONTRAST ]

Press this button to adjust picture contrast. Adjust the value with the VOLUME/SELECT 6 or the SELECT

7 buttons. Also used as a control button in the menu

function mode.

5 Menu button [MENU]

Displays and disappears the <MENU> screen. Pressing the PHASE button with the Menu button depressed will display the <SET-UP MENU> screen.

6 Volume/Select buttons [VOLUME/

SELECT –

Adjusts the speaker volume. Also used as a control button in the menu function mode.

+] (TM-A13SU and TM-A13SU-W only)

7 Select buttons [SELECT – /+] (TM-A13UCV only)

Used as a control button in the menu function mode.

8 Input B button [INPUT SELECT B]

Selects the video signal input to the VIDEO B terminal and the audio signal input to the AUDIO B terminal (RCA connector) on the rear panel. When selected, the input B indicator @ lights.

–+

VOLUME/SELECT

–+

SELECT

B A

INPUT SELECT

(Front Panel view of TM-A13SU shown)

B A

INPUT SELECT

POWER

OFF

ON OFF

Notes:

* The VIDEO B terminals include a video terminal (BNC

connector) and a Y/C terminal (mini-DIN 4-pin connector). The Y/C (S-video) terminal is given priority.

* There is no Y/C terminal or A UDIO B terminal on the TM-

A13UCV. They are only available on the TM-A13SU and TM-A13SU-W.

9 Input A button [INPUT SELECT A]

Selects the video signal input to the VIDEO A terminal (BNC connector) and the audio signal input to the AUDIO A terminal (RCA connector) on the rear panel. When selected, the input A indicator # lights.

Note:

* There is no AUDIO A terminal on the TM-A13UCV. It is

only available on the TM-A13SU and TM-A13SU-W.

10 Power indicator

Lights in green when the power is ON.

Lit : When the power is on. Unlit : When the power is off.

11 Power switch [POWER ]

Press this switch to turn the power on or off. _ ON : Power is turned on. — OFF : Power is turned off.

12 Input B indicator

Lights in green when the Input B is selected.

13 Input A indicator

Lights in green when the Input A is selected.

14 Built-in speaker

(TM-A13SU and TM-A13SU-W only)

The speaker is located inside.

TM-A13SU

TM-A13UCV

REAR VIEW

[TM-A13SU / TM-A13SU-W]

VIDEO AUDIO

BAB

OUT

Y/C IN

OUT

[TM-A13UCV]

VIDEO

OUT

15 Video A terminals [VIDEO A IN/OUT]

Video signal input (IN) and output (OUT) terminals. The output terminal is bridge-connected.

IN : Video signal input terminal OUT : Bridge-connected video signal output terminal

Notes:

* For corresponding audio signals, use the AUDIO A

terminals &.

* There is no AUDIO A terminal on the TM-A13UCV. It is

only available on the TM-A13SU and TM-A13SU-W.

* Also refer to the Basic connection Example on page 11.

16 Video B terminals [VIDEO B IN/OUT]

[ BNC connector ]

Video signal input (IN) and output (OUT) terminals. The output terminal is bridge-connected.

IN : Video signal input terminal OUT : Bridge-connected video signal output terminal

[ Y/C connector ] (TM-A13SU and TM-A13SU-W only)

Y/C (S-Video) signal input (mini-DIN 4-pin connector) terminal.

Y/C IN : Y/C signal input terminal.

Notes:

* For corresponding audio signals, use the AUDIO B

terminals *.

* There is no Y/C terminal or AUDIO B terminal on the

TM-A13UCV. They are only available on the TM-A13SU

and TM-A13SU-W. * There is no Y/C (S-video) signal output terminal. * When both VIDEO B terminals are connected (input) at

the same time, the Y/C terminal is given priority. * Also refer to the Basic connection Example on page 11.

To AC outlet (120 V AC, 50/60 Hz)

17 Audio A terminal [A UDIO A IN/OUT]

18 Audio B terminals [AUDIO B IN/OUT]

19 AC Inlet [AC IN]

20 Power cord

VIDEO AUDIO

BAB

Y/C IN

OUT

(Rear view of TM-A13SU shown)

(TM-A13SU and TM-A13SU-W only) Input (IN) and output (OUT) terminals for the audio signal corresponding the VIDEO A terminals %. The output terminal is bridge-connected.

IN : Audio signal input terminal OUT : Bridge-connected audio signal output terminal

Notes:

* For corresponding video signals, use the VIDEO A

terminal %.

* There is no AUDIO A terminal on the TM-A13UCV. It is

only available on the TM-A13SU and TM-A13SU-W.

* Also refer to the Basic connection Example on page 11.

(TM-A13SU and TM-A13SU-W only) Input (IN) and output (OUT) terminals for the audio signals corresponding to the VIDEO B terminals ^. The output terminal is bridge-connected.

IN : A udio signal input terminal OUT : Bridge-connected audio signal output terminal

Notes:

* For corresponding video signals, use the VIDEO B

terminals ^.

* There is no Y/C terminal or AUDIO B terminal on the

TM-A13UCV. They are only available on the TM-A13SU and TM-A13SU-W.

* Also refer to the Basic connection Example on page 11.

Power input connector. Connect the provided AC power cord ) to an AC outlet (120 V AC, 50/60 Hz).

Connects the provided power cord (120 V AC, 50/60 Hz) to the AC IN connector.

+ 11 hidden pages