JVC TK-AM200U - Active Movement Color Dome Camera Instructions Manual
3
TK-AM200
INSTRUCTIONS
For Customer Use:
Enter below the Serial No. which is
located on the body. Retain this
information for future reference.
Model No. TK-AM200
Serial No.
This instruction book is made from
100% recycled paper.
ACTIVE MOVEMENT VIDEO CAMERA
SC96866-001
2
IMPORTANT SAFEGUARDS
1. Read all of these instructions.
2. Save these instructions for later use.
3. All warnings on the product and in the operating instructions should be adhered to.
4. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
5. Do not use attachments not recommended by the appliance manufacturer as they may
cause hazards.
6. Do not use this appliance near water - for example, near a bathtub, washbowl, kitchen
sink, or laundry tub, in a wet basement, or near a swimming pool, etc.
7. Do not place this appliance on an unstable cart, stand, or table. The
appliance may fall, causing serious injury to a child or adult, and
serious damage to the appliance.
Use only with a cart or stand recommended by the manufacturer , or
sold with the appliance. Wall or shelf mounting should follow the
manufacturer’ s instructions, and should use a mounting kit appro v ed
by the manufacturer. An appliance and cart combination should be
moved with care.
Quick stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.
8. Slots and openings in the cabinet and the back or bottom are provided for v entilation, and
to insure reliable operation of the appliance and to protect it from overheating, these
openings must not be blocked or covered. The openings should never be blocked by
placing the appliance on a bed, sofa, rug, or other similar surface.
This appliance should never be placed near or over a radiator or heat register. This appliance should not be placed in a built-in installation such as a bookcase unless proper
ventilation is provided.
9. This appliance should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of po wer supplied to y our home , consult y our
dealer or local power company. For appliance designed to operate from battery power,
refer to the operating instructions.
10.This appliance system is equipped with a 3-wire grounding type plug (a plug having a
third (grounding) pin). This plug will only fit into a grounding-type power outlet. This is a
safety feature. If you are unable to insert the plug into the outlet, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the grounding plug.
11.For added protection for this product during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the product due to lightning and
power-line surges.
12.Do not allow anything to rest on the power cord. Do not locate this appliance where the
cord will be abused by persons walking on it.
PORTABLE CART WARNING
(symbol provided by RETAC)
S3126A
3
13.Follow all warnings and instructions marked on the appliance.
14.Do not overload wall outlets and extension cords as this can result in fire or electric shock.
15.Never push objects of any kind into this appliance through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the appliance.
16.Do not attempt to service this appliance yourself as opening or removing covers may
expose you to dangerous voltage or other hazards . Refer all servicing to qualified service
personnel.
17.Unplug this appliance from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the appliance.
c. If the appliance has been exposed to rain or water.
d. If the appliance does not operate normally by following the operating instructions. Ad-
just only those controls that are covered by the operating instructions as improper
adjustment of other controls may result in damage and will often require extensive
work by a qualified technician to restore the appliance to normal operation.
e. If the appliance has been dropped or the cabinet has been damaged.
f. When the appliance exhibits a distinct change in performance - this indicates a need
for service.
18.When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same char acteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
19.Upon completion of any service or repairs to this appliance, ask the service technician to
perform routine safety checks to determine that the appliance is in safe operating
condition.
4
CAUTION:TO REDUCE THE RISK OF ELECTRIC
SHOCK. DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE.REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
This device complies with part 15 of the FCC Rules.
Changes or modifications not approved by JVC could
void the user’s authority to operate the equipment.
Due to design modifications, data given in this
instruction book are subject to possible change
without prior notice.
AVERTISSEMENT:
POUR EVITER LES RISQUES
D’INCENDIE OU D’ELECTROCUTION, NE PAS EXPOSER
L’APP AREIL A L’HUMIDITE OU A LA
PLUIE.
Safety Precautions
INFORMATION (FOR CANADA)
RENSEIGNEMENT
(POUR CANADA)
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la Class B est
conforme á la norme NMB-003 du Canada.
5
Thank you for purchasing this product.
(These instructions are for TK-AM200U.)
CONTENTS
INTRODUCTION
Features.............................................................................................................................. 6
Safety Precautions .............................................................................................................. 6
Operating Precautions........................................................................................................ 7
Controls, Connectors and Indicators...................................................................................8
Camera Body ................................................................................................................. 8
Ceiling Mount ................................................................................................................. 9
SYSTEM
RM-P2580 System............................................................................................................ 10
INSTALLATION
Connections to Terminal Board ........................................................................................ 12
Camera Settings ............................................................................................................... 14
Ceiling Installation ............................................................................................................ 16
Changing Camera Settings Using the RM-P2580
Menu Operations .............................................................................................................. 18
Menu Screen Flow............................................................................................................ 19
CAMERA MODE SELECT Screen................................................................................... 20
CAMERA VIDEO ADJUST Screen ................................................................................... 21
AWC ADJUST Screen...................................................................................................... 22
VIDEO ADJUST FOR POSI Screen................................................................................. 23
PANIC ALARM SET Screen ............................................................................................. 24
FACTORY SETTINGS Screen.......................................................................................... 24
BLC EDIT Screen ............................................................................................................. 25
CAMERA TEXT Setting.................................................................................................... 26
POSITION TEXT Setting .................................................................................................. 27
AUTO PAN Setting............................................................................................................ 28
AUTO PATROL Setting ..................................................................................................... 30
OTHERS
PANIC ALARM .................................................................................................................. 32
Specifications.................................................................................................................... 34
6
INTRODUCTION
n Active movement camera with integrated
moving mechanism and camera.
n Backlight compensation function
provided. Enables improvement of video
image shot under backlit conditions.
n Electronic shutter with a selectable
shutter speed of 1/100 sec reduces
flickering caused by fluorescent lighting
in areas where the commercial power
supply frequency is 50 Hz.
n Employment of TTL automatic tracking
white balance allows use under various
light source conditions.
n Panic alarm input terminal provided.
n Electronic zoom function.
n Control possible via external control
signal conforming to the EIA/TIA RS422A or RS-485 standard. The unit can
be controlled using the optional JVC
Remote Control Unit RM-P2580.
n The following functions are available
when used in combination with the JVC
Remote Control Unit RM-P2580.
• Many kinds of function can be set using
menus.
• Camera text, position text setting.
• Auto panning function
• Auto patrol function
This function outputs the video image
at specified pre-set positions in the set
order.
Features Safety Precautions
Installation of this unit requires expertise.
Please contact your JVC dealer for details.
Be sure to tighten the screws and nuts used
for installation securely . Insufficient tightening
could cause the unit to fall from its mount.
7
Operating Precautions
● To save energy, be sure to tur n off the
system when not in use.
● This camera has been designed for indoor
use. It cannot be used outdoors.
● This camera has been designed
exclusively to be hung from the ceiling. It
may malfunction if it is placed standing
on a surface or if it is installed in a tilted
position.
● Do not install or use the camera in the
following places.
• In a place exposed to rain or water.
• In a place with vapor or oil soot, for
example in a kitchen.
• Where the temperature is outside the
allowed operating temperature range
(−10°C to 50°C).
• Near a source of radiation, X-rays,
strong radio waves or magnetism.
• In a place subjected to vibrations.
• In a place with excessive dirt.
● The camera incorporates an AGC circuit.
When it is used under low light conditions,
the camera sensitivity is automatically
boosted and the picture may look grainy.
This is not a malfunction.
● Use the ATW (auto-tracking white
balance) mode when the camera is used
under fluorescent lighting. If set to
MANUAL, the correct white balance may
not be accomplished.
● When this camera is used in the ATW
(auto-tracking white balance) mode, the
recorded colors may be slightly different
from the actual colors due to the
operational principles of the auto-tracking
white balance circuit. This is not a
malfunction.
● If a high-intensity object (such as a lamp)
is shot, the image on the screen may have
vertical lines (smear) or blur (blooming)
at its periphery. This is a characteristic of
the CCD; and it is not a defect.
● The camera’s electronic shutter is set to
1/60 s when shipped from the factory.
When the camera is used under
fluorescent lighting in an area with a local
power frequency of 50 Hz, please set the
shutter to 1/100 s on remote control unit.
(Sensitivity will decrease slightly at the 1/
100 s setting.)
● When dirt adheres to the dome cover , the
image will be difficult to see. Be sure to
clean the lens and the dome cover
periodically . Use a soft cloth for cleaning.
Do not use thinner, benzene, etc. If very
soiled, soak the cloth in a neutral
detergent diluted with water and wipe
clean. Then wipe with a dry cloth.
Precautions for use with the RM-P2580
● Focus (including AF) cannot be used.
● Do not select more than maximum 16
preset positions.
● ALARM TEXT EDIT 1 to EDIT 10
cannot be used.
8
1
Terminal board
To connect the coaxial cable used as the
video signal cable, the power cable, the
control signal cable, and the alarm input
signal cable. (Z See page 12.)
2
Video output terminal
Outputs composite video signals
(1V(p-p), output impedance 75 Ω).
3
Control signal connection terminals
Terminals for inputting signals with electrical characteristics conforming to the
EIA/TIA RS-422A or RS-485 standard.
4
AC 24 V input terminal
To input AC 24 V power.
5
Panic alarm signal input terminal
T erminal for inputting the panic alarm signal. Settings concerning the panic alarm
signal should be made using the PANIC
ALARM SET screen. (Z See pages 24
and 32.)
6
Terminal board cover
Protects the cable connection terminals
from dirt, etc.
7
Camera body mounting guides (×3)
To be inserted into the guide holes 16 of
the ceiling mount.
8
Camera body clamp
Fix the camera body to the ceiling mount
by fastening the ceiling mount’s camera
clamping screw
18
to this clamp.
9
Drop prevention wire hook
Attach the drop prevention wire 20 from
the ceiling mount to this hook.
10
Switch cover
Open this cover to use the setting
switches. The cover can be opened by
pushing the cover edge in the direction
of the arrow.
11
Control signal selector switch
(RS-422A/RS-485, RS-232C)
Switches the communication mode of the
control signal terminal
3
.
• When connected to the RM-P2580, set
to the RS-422A/RS-485 side.
• When connected to a personal computer, etc. set to the RS-232C side.
Controls, Connectors and Indicators
n Camera Body (With terminal board in attached condition)
INTRODUCTION
(Side view)
7
6
9
2
7
7
3
5
4
1
8
0
$
#@!
9
12
System setting switches
Set switches in accordance with the system to be connected to.
The settings comprise setting the form
of the control signal cable connection,
communication protocol, control signal
termination ON/OFF , and image synchronization method.
(Z See “Camera Settings” on page 14.)
13
Camera ID setting switches
Use to set the camera ID.
Be sure to set the camera ID when switch
1 of the system setting switches
12
is
set to ON (MULTIDROP).
(Z See “Camera Settings” on page 14.)
14
FOR SERVICE connector
Exclusively for service purposes.
Ceiling Mount
15
Mounting holes (×4)
Use these holes to attach the ceiling
mount to the ceiling.
16
Guide holes for mounting camera (×3)
Guide holes for mounting the camera
body . The camera body mounting guides
7
are inserted into these holes.
17
Camera direction alignment mark
When mounting the ceiling mount to the
ceiling, align this mark with the center of
the direction in which you want the camera to face.
18
Camera clamping screw
T o hold the camera body in place , be sure
to use this screw to clamp the camera
clamp
8
.
19
Positioning alignment protrusion
When attaching the camera body, align
the camera clamp 8 on the camera
body with this protrusion.
20
Drop prevention wire hook
Attach this wire to the drop prevention
wire hook
9
on the camera body.
21
Safety wire attachment hole
To prevent the camera from accidentally
dropping down, fasten a wire from the
ceiling to this hole using an M3 screw.
(Z See “Ceiling Installation” step
2.
on
page 16.)
n Ceiling Mount
21
%
%
*
^
)
&
^
%
^
%
(
10
SYSTEM
RM-P2580 System
n System with up to 8 cameras
(Sixteen position settings available for each camera.)
• Confirm switch settings on the screen as follows.
q Confirm that the image from the camera to be
checked is displayed on the monitor.
w Turn OFF and then ON the AC 24 V power to the
camera to be checked.
e The camera begins the initial operation and
characters similar to those shown in the illustration
on the right appear on the monitor screen.
r Confirm that “DUPLEX” and “ID-
” are displayed
and that the ID number is the correct number (the
number should be the same as the number of the
VIDEO INPUT terminal to which the camera is
connected on the rear panel of the RM-P2580).
t If wrong, set the camera ID again.
MONITOR screen
(example showing camera ID as “05”)
“DUPLEX” should
be displayed.
The number shown in
the □□ part of ID-□□
should be correct.
REC
PLAY
FFREW
REVERSE
PAUSE/
STILL
REC
CHECK
STOP/EJECT
COUNT/
CLOCK
TIME
MODE
TIMER
REC
AL/PL
RESET
MENU
VIDEO CASSETTE RECORDER
SHIFT/TRACKING
SET/V.LOCK
RESET
/CANCEL
OPERATE
SR-L910
OPE. LOCK
1
TO CAMERATO CAMERA DATA I / ODATA I / O
RXRX
+
{
RX
-
|
TX
+
{
TX
-
|
COMCOM
1 2 3 4 5 6 7 8
COMCOM
9/110/2 11/312/4 13/514/615/7 16/8
COMCOM COMCOM COMCOM
CAMERACAMERA
SW
UNIT
ALARM
AUTO
4312 8756
2 3 4 5 6 7
8
1
MONITOR
OUTPUT
MONITOR
SERIAL-2SERIAL-1
VIDEO INPUT
VIDEO OUTPUT
OUTPUT
2
1
ON
2 3 4 5 6 7
8
POWER
OFF
ON
AC INPUT
‘
IN TIALI
PROT OOLDUPLEXID-05C
Camera
TK-AM200
Camera
TK-AM200
Camera
TK-AM200
Camera 1
Camera 2
Camera 8
Camera ID: 01
Termination: OFF
Camera ID: 02
Termination: OFF
Camera ID: 08
Termination: ON
Control signal cable
Video signal cable
Power cable
Remote Control Unit
RM-P2580
Time lapse VCR
MONITOR
MONITOR
AC24V
AC24V
AC24V
CAM SW
OUT
VIDEO IN
COM
CAMERA
SW
TO
CAMERA
MONITOR
OUTPUT 2
MONITOR
OUTPUT 1
Memo:
• When operating a system using the RM-P2580, several cameras (up to 8) can be connected and
used on one control signal cable. Consequently, an incorrect switch setting on just a single camera
will cause the entire system to work incorrectly.
11
n Connections
n Settings
When connecting
●Turn OFF the power supply to all equipment to be used before making connections.
●Carefully read the Instruction Manual for each piece of equipment to be used before
making connections.
●For the appropriate connection cables and the length of these, carefully read “Connections
to Camera Terminal Board” on page 12.
●The control signal cable cannot be used for loop connection.
Lug plates
AC 24 V power cable
To AC 24V power
supply
To RM-P2580
T o VIDEO INPUT
terminal on
RM-P2580
Connecting the control signal cable
(
Use a twisted-pair cable for connection. Z See page 13.
)
Camera 2
terminal board
Connect:
Camera TX+ to RM-P2580 RX+
Camera TX– to RM-P2580 RX–
Camera RX+ to RM-P2580 TX+
Camera RX– to RM-P2580 TX–
The A B C D mar ks indicated
on both the camera terminals
and the RM-P2580 terminals
facilitate correct connections.
Connect the terminals with
identical marks.
C TX+
D TX–
A RX+
B RX–
TX+ A
TX
– B
RX
+ C
RX– D
TX
+ A
TX
– B
RX
+ C
RX– D
TX
+ A
TX
– B
RX
+ C
RX– D
RM-P2580
Camera 1
terminal board
Camera 3
terminal board
Control
signal cable
Video signal cable
(coaxial cable)
Terminal board
RX+ C
RX– D
A TX+
B TX–
1234
ON
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
Camera ID setting switches
Set to match the RM-P2580 VIDEO
INPUT terminal number for each
camera.
Switch 3: Set this to ON (signal termination ON) only
on the camera placed at the end of the
control signal cable.
Set to OFF on all other cameras.
Switch 2: Set to OFF (DUPLEX) side.
Switch 1: Set to ON (MULTIDROP) side.
Control signal selector switch:
Set to the RS-422A/RS-485 side.
(Example: Camera 1
ID “×10” position 0,
ID “×1” position 1)
Switch 4: Select the synchronization method of the
camera image.
Set the switch on all cameras to ON (Line
Lock) and match with the V. PHASE.
(Only possible in 60 Hz regions.)
(Z See page 20.)
Loading...