JVC TH-BA1, TH-BA3 User Manual
ENGLISH
Warnings, Cautions and Others / Mises en garde, précautions et indications diverses
HOME THEATER SOUND SYSTEM
TH-BA3
—Consists of SP-THBA3F, RX-THBA3,
SP-THBA3S and SP-THBA3W
TH-BA1
—Consists of CA-THBA1 and SP-THBA1
Thank you for purchasing a JVC product.
Before operation, please read the instructions carefully.
For customer use:
Enter below the Model No. and Serial No. which are located either on
the rear, bottom or side of the cabinet. Retain this information for future
reference.
Model No.
Serial No.
INSTRUCTIONS
© 2009 Victor Company of Japan, Limited
CAUTION (SP-THBA3F/CA-THBA1)
The
button in any position does not disconnect the mains line.
Disconnect the mains plug to shut the power off completely (the STANDBY
lamp goes off). The MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain readily operable.
When the System is on standby, the STANDBY lamp lights red.
•
When the System is turned on, the STANDBY lamp goes off.
•
The power can be remote controlled.
CAUTION (SP-THBA3W/SP-THBA1/RX-THBA3)
The power supply to the subwoofer is linked to the center unit. Disconnect the
mains plug to shut the power off completely (the POWER ON lamp goes off).
The MAINS plug or an appliance coupler is used as the disconnect device, the
disconnect device shall remain readily operable.
When the System is on standby, the STANDBY/ON lamp lights red.
•
When the System is turned on, the STANDBY/ON lamp lights blue.
•
ATTENTION (SP-THBA3F/CA-THBA1)
La touche
système du secteur. Déconnectez la fiche de secteur pour mettre l’appareil
complètement hors tension (le témoin STANDBY s’éteint). La fiche secteur
ou un coupleur est utilisé comme dispositif de déconnexion de l’appareil, et
l’appareil déconnecté doit être prêt à être utilisé.
•
Quand le système est en attente, le témoin STANDBY est allumé en rouge.
•
Quand le système est sous tension, le témoin STANDBY s’éteint.
L’alimentation peut être télécommandée.
ATTENTION (SP-THBA3W/SP-THBA1/RX-THBA3)
L’alimentation du caisson de grave est reliée à l’unité centrale. Déconnectez
la fiche secteur pour mettre l’appareil complètement hors tension (le témoin
POWER ON s’éteint).
La fiche secteur ou un coupleur est utilisé comme dispositif de déconnexion de
l’appareil, et l’appareil déconnecté doit être prêt à être utilisé.
Quand le système est en attente, le témoin STANDBY/ON est allumé en rouge.
•
Quand l’appareil est sous tension, le
•
Do not use another AC adaptor to connect this model.
N’utilisez aucun autre ADAPTATEUR SECTEUR pour connecter ce modèle.
, dans n’importe quelle position, ne déconnecte pas le
GVT0289-018B[J/C]
0709WMKMDWJMM
témoin STANDBY/ON
EN
est allumé en bleu.
For U.S.A.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
Pour les Etats-Unis
Le symbole de l’éclair à l’intérieur d’un triangle équilatéral est
destiné à alerter l’utilisateur sur la présence d’une “tension
dangereuse” non isolée dans le boîtier du produit. Cette tension
est suffisante pour provoquer l’électrocution de personnes.
Le point d’exclamation à l’intérieur d’un triangle
équilatéral est destiné à alerter l’utilisateur sur la présence
d’opérations d’entretien importantes au sujet desquelles des
renseignements se trouvent dans le manuel d’instructions.
CAUTION
Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
ATTENTION
Les piles ne doivent en aucun cas être exposées à une chaleur excessive
(lumière du soleil, feu, etc.).
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
Do not remove screws, covers or cabinet.
1.
Do not expose this appliance to rain or moisture.
2.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1.
Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l’appareil.
2.
Ne pas exposer l’appareil à la pluie ni à l’humidité.
CAUTION
Do not block the ventilation openings or holes. (If the ventilation openings
•
or holes are blocked by a newspaper or cloth, etc., the heat may not be able
to get out.)
Do not place any naked flame sources, such as lighted candles, on the
•
apparatus.
When discarding batteries, environmental problems must be considered and
•
local rules or laws governing the disposal of these batteries must be followed
strictly.
Do not expose this apparatus to rain, moisture, dripping or splashing and
•
that no objects filled with liquids, such as vases, shall be placed on the
apparatus.
ATTENTION
•
Ne bloquez pas les orifices ou les trous de ventilation. (Si les orifices ou les
trous de ventilation sont bloqués par un journal un tissu, etc., la chaleur peut
ne pas être évacuée correctement de l’appareil.)
•
Ne placez aucune source de flamme nue, telle qu’une bougie, sur l’appareil.
•
Lors de la mise au rebut des piles, veuillez prendre en considération les
problèmes de l’environnement et suivre strictement les règles et les lois
locales sur la mise au rebut des piles.
N’exposez pas cet appareil à la pluie, à l’humidité, à un égouttement ou à des
•
éclaboussures et ne placez pas des objets remplis de liquide, tels qu’un vase,
sur l’appareil.
For U.S.A.
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE.
Pour les Etats-Unis
AVERTISSEMENT
POUR PRÉVENIR LES RISQUES D’INCENDIE OU DE CHOCS ÉLECTRIQUES, NE PAS
EXPOSER CE APPAREIL À LA PLUIE OU À L’HUMIDITÉ.
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
Front: No obstructions and open spacing.
1.
Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below.
2.
Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm (3-15/16”) or more.
3.
ATTENTION: Aération correcte
Pour prévenir tout risque de décharge électrique ou d'incendie et éviter toute détérioration, installez l'appareil de la manière suivante:
Avant: Bien dégagé de tout objet.
1.
Côtés/dessus/dessous: Assurez-vous que rien ne bloque les espaces indiqués sur le schéma ci-dessous.
2.
Dessous: Posez l’appareil sur une surface plane et horizontale. Veillez à ce que sa ventilation correcte puisse se faire en le plaçant sur un support d’au moins
3.
dix centimètres de hauter.
TH-BA3
Front / Face
15 cm
(5-15/16")
TH-BA1
Front / Face
(5-15/16")
For U.S.A.
Caution: Changes or modifications not expressly approved by party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
–
Increase the separation between the equipment and receiver.
–
Connect the equipment into an outlet on a circuit different from that to
–
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
–
Pour les Etats-Unis
Attention : Les changements ou les modifications qui ne sont pas
explicitement approuvés par la partie responsable de l’observance pourraient
mettre fin au droit de l’utilisateur d’utiliser le matériel.
Remarque : Cet appareil a été testé et il s’est avéré conforme aux limites
applicables à un appareil numérique de classe B, en vertu de la Partie 15
des Règles de la FCC. Ces limites sont conçues de manière à assurer une
protection raisonnable contre les interférences nuisibles dans une installation
résidentielle. Cet appareil produit, utilise et peut émettre une énergie de haute
fréquence et, s’il n’est pas installé et utilisé en conformité avec les instructions,
il peut causer des interférences nuisibles aux communications radio. Il n’y a,
toutefois, aucune garantie que des interférences ne se produiront pas dans une
installation particulière. Si cet appareil cause effectivement des interférences
nuisibles à la réception de la radio ou de la télévision, ce qu’on peut établir
en mettant l’appareil en marche et à l’arrêt, nous encourageons l’utilisateur à
tenter de corriger l’interférence par une ou plusieurs des mesures suivantes :
réorienter ou déplacer l’antenne de réception;
–
accroître la séparation entre l’appareil et le récepteur;
–
brancher l’appareil dans une prise ou un circuit autre que celui auquel le
–
récepteur est branché;
consulter un vendeur ou un technicien radio/TV expérimenté pour obtenir
–
de l’aide.
Manufactured under license from Dolby Laboratories. Dolby, Pro Logic,
•
and the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent numbers: 5,451,942;
•
5,956,674; 5,974,380; 5,978,762; 6,487,535 and other U.S. and
worldwide patents issued and pending. DTS and DTS Digital Surround
are registered trademarks and the DTS logos and Symbol are trademarks
of DTS, Inc. © 1996-2008 DTS, Inc. All Rights Reserved.
RX-THBA3 SP-THBA3S
15 cm
2 cm (13/16")
SP-THBA3F
2 cm (13/16")
CA-THBA1
2 cm (13/16")
SP-THBA3W
SP-THBA3S
SP-THBA1
For SP-THBA3, RX-THBA3, SP-THBA3W, CA-THBA1 and SP-THBA1
This device compiles with RSS-210 of Industry Canada Rules. Operation
is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Pour SP-THBA3, RX-THBA3, SP-THBA3W, CA-THBA1 et SP-THBA1
Cet appareil est conforme au réglement CNR-210 de l’industrie du Canada.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes:
(1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit étre
prét à accepter tout brouillage radioélectrique reçu, mê
susceptible de compromettre le fonctionnement du dispositif.
For Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO
NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCECAUSING EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,” ICES-003 OF
THE DEPARTMENT OF COMMUNICATIONS.
Pour le Canada
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQUES
APPLICABLES AUX APPAREILS NUMIRIQUES DE CLASSE B PRESCRITES DANS LA
NORME SUR LE MATERIEL BROUILLEUR; “APPAREILS NUMERIQUES”, NMB-003
EDICTEE PAR LE MINISTRE DES COMMUNICATIONS.
For SP-THBA3, RX-THBA3, SP-THBA3W, CA-THBA1 and SP-THBA1
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the manufacturer for
compliance could void the user’s authority to operate the equipment.
Pour SP-THBA3, RX-THBA3, SP-THBA3W, CA-THBA1 et SP-THBA1
Cet appareil est conforme à la partie 15 des règles de la FCC (Federal
Communications Commission). Le fonctionnement est sujet aux deux
conditions suivantes : (1) Cet appareil ne peut pas causer d’interférences
nuisibles, et (2) cet appareil doit accepter toute interférence reçue, y compris
des interférences qui peuvent causer un mauvais fonctionnement.
Tout changement ou modification non expressément approuvés par le fabricant
pour conformité peut annuler l’autorité de l’utilisateur d’utiliser l’appareil.
[European Union only]
[Union européenne seulement]
15 cm (5-15/16")
15 cm (5-15/16")
10 cm (3-15/16")
15 cm (5-15/16")
15 cm (5-15/16")
10 cm (3-15/16")
me si ce brouillage est
Introduction
Notes on handling
Important cautions
Installation of the System
Select a place which is level, dry, and neither too hot nor too cold; between
•
5°C and 35°C (41°F and 95°F).
Leave sufficient distance between the System and the TV.
•
Do not use the System in a location near heat sources, or in a place subject to
•
direct sunlight, excessive dust, or vibration.
Install the System in a location with adequate ventilation to prevent internal
•
heat buildup.
Power cord
Do not handle the power cord with wet hands.
•
A small amount of power is always consumed while the power cord is
•
connected to the wall outlet.
Do not pull on the cord to unplug the power cord. When unplugging the
•
power cord, always grasp and pull the plug so as not to damage the cord.
To prevent malfunctions of the System
There are no user-serviceable parts inside. If anything goes wrong, unplug
•
the power cord and consult your dealer.
Do not insert any metallic objects or liquids into the System.
•
Safety precautions
Avoid moisture, water, and dust
Do not place the System in moist or dusty places.
Avoid high temperatures
Do not expose the System to direct sunlight and do not place it near any
heating devices.
When you are away
When away on holiday or for other reasons for an extended period of time,
disconnect the power cord from the wall outlet.
Do not block the vents
Blocking the vents may damage the System.
Care of the cabinet
Stains on the System should be wiped off with a soft cloth. If the System
•
is heavily stained, wipe it with a cloth soaked in water diluted neutral
detergent and wrung well, then wipe clean with a dry cloth.
Since the System may deteriorate in quality, become damaged or get its
•
paint peeled off, be careful about the following:
DO NOT wipe it forcefully.
–
DO NOT wipe it with thinners, benzines or other organic solvents including
–
disinfectants.
DO NOT apply any volatile substances such as insecticides to it.
–
DO NOT allow any rubber or plastic to remain in contact with it for a long
–
time.
Do not place anything on top of the System. Doing so may cause the System
•
to fall, causing malfunctioning and/or injury.
The manufacturer accepts absolutely no liability for any accidents or damage
•
resulting from inadequate assembly or mounting, insufficient strength of
attachment, misuse or abuse, or natural disasters.
If water gets inside the System
Turn the System off and disconnect the power cord from the wall outlet,
then call the store where you purchased this System. Using the System in this
condition may cause a fire or electrical shock.
Supplied accessories
Check to make sure you have all of the supplied accessories.
If anything is missing, contact your dealer immediately.
Remote control TH-BA3: RM-STHBA3A (× 1)
•
TH-BA1: RM-STHBA1A (× 1)
AC adaptor (AA-R1902) TH-BA3: (× 2) / TH-BA1: (× 1)
•
AC power cord TH-BA3: (× 2) / TH-BA1: (× 1)
•
Lithium coin battery CR2025 (× 1)
•
The battery has been installed in the remote control when shipped from
–
the factory.
Core filter (× 2)
•
Specifications
Center unit (SP-THBA3F / CA-THBA1)
Output power
Center/ Front Surround: 120 W (30 W per channel-measure at
Audio section
Analog Input ANALOG: 1 Vrms/50 kΩ
Digital Input*
Speaker section
Type: Full-Range Bass-Reflex Type (Magnetically-
Speaker: 8 cm (3-3/16”) cone × 4
Power Handling Capacity: 30 W
Impedance: 4 Ω
Frequency Range: Center Speakers: 84 Hz to 22 kHz
Front Speakers: 84 Hz to 22 kHz
Sound Pressure Level: Center Speakers: 82 dB/W•m
Front Speakers: 82 dB/W•m
General
Power Source (DC IN): DC19 V
AC adaptor (AA-R1902): Input: AC 110-240 V 1.5-0.9 A, 50/60 Hz
Dimensions (W × H × D): 900 mm ×125 mm × 85 mm
(35-7/16” × 4-15/16” × 3-3/8”)
Mass: 3.5 kg (7.8 lbs)
1
DIGITAL 1, DIGITAL 2: –21 dBm to –15 dBm
Powered subwoofer (SP-THBA3W / SP-THBA1)
Output power 100 W, RMS at 3 Ω at 45 Hz, with 10%
Type: 1-Way Bass-Reflex Type
Speaker: 16 cm (6-5/16”) cone × 1
Power Handling Capacity: 100 W
Impedance: 3 Ω
Frequency Range: 45 Hz to 5 kHz
Sound Pressure Level: 82 dB/W•m
1 kHz Optical Digital In at full scale
sinewave), RMS at 4 Ω at 1 kHz, with
10% total harmonic distortion
(660 nm ±30 nm)
Shielded Type)
3.37 A
Output: DC19 V 3.37 A
total harmonic distortion
Power Requirements: AC 120 V
Power Consumption: 30 W (during operation)
0.8 W (in Standby mode)
Dimensions (W × H × D): 215 mm × 352 mm × 254 mm
Mass: 5 kg (11 lbs)
(8-1/2” × 13-7/8” × 10”)
Wireless receiver unit (RX-THBA3)*
Output power: 30 W per channel, RMS at 4 Ω at
Power Source (DC IN): DC19 V 3.37 A
AC adaptor (AA-R1902): Input: AC 110 – 240 V 1.5-0.9 A,
Output: DC 19 V 3.37 A
Dimensions (W × H × D): 186 mm × 30.8 mm × 300 mm
(7-3/8” × 1-1/4” × 11-13/16”)
Mass: 0.53 kg (1.2 lbs)
1 kHz, with 10% total harmonic
distortion
50/60 Hz
Surround speaker (SP-THBA3S)*
Type: Full-Range Bass-Reflex Type
Speaker: 8 cm (3-3/16”) cone × 1
Power Handling Capacity: 30 W
Impedance: 4 Ω
Frequency Range: 84 Hz to 22 kHz
Sound Pressure Level: 82 dB/W•m
Dimensions (W × H × D): 105 mm × 118 mm × 98 mm
Mass: 0.46 kg (1.01 lbs) each
1
*
Corresponding to Linear PCM, Dolby Digital, and DTS (with sampling frequency
— 32 kHz, 44.1 kHz, 48 kHz)
2
*
Only for TH-BA3
Designs & specifications are subject to change without notice.
(4-3/16” × 4-11/16” × 3-7/8”)
, 60 Hz
2
2
Getting started
: Only for TH-BA3 / : Only for TH-BA1
DO NOT connect the power cord until all other connections have
been made.
Prepare the Remote Control
When you use the remote control for the first time, pull out the insulation
sheet.
Insulation sheet
If the range or effectiveness of the remote
control decreases, replace the battery.
To Replace the Battery in the Remote Control
Insert the battery into the remote control by matching the polarities (+ and –)
correctly.
Lithium coin battery
(product number: CR2025)
1 Pinch the side of the battery case.
2 Pull out the battery case and insert
the battery by matching the polarities.
NOTE
Store the battery in a place where children cannot reach. If a child accidentally
•
swallows the battery, consult a doctor immediately.
To prevent the battery from overheating, cracking, or starting a fire:
•
Do not recharge, short, disassemble or heat the battery, or dispose of it in a
–
fire.
Do not leave the battery with other metallic materials.
–
Wrap the battery with tape and insulate when throwing away or saving it.
–
Do not poke the battery with tweezers or similar tools.
•
Dispose of the battery in the proper manner, according to federal, state, and
•
local regulations.
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
For USA-California Only
This product contains a CR Coin Cell Lithium Battery which contains
Perchlorate material—special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
Speaker layout
Install the speakers on a flat and level surface to ensure the best sound quality.
The sound may be affected depending on the location in which you install
•
them. To avoid such issues, change the location and orientation of the
speakers.
Install the speakers leaving an appropriate distance between them.
•
If you install the speakers near the TV, color distortion may occur. To prevent
•
this, turn off the TV’s main power or unplug it before installing the speakers.
Wait at least 30 minutes before turning on the TV’s main power again.
If the TV is still affected, move the speakers further away.
•
Operations
Connect the wireless receiver
Typical installation
unit to the surround speakers.
NOTE
To obtain the best possible
•
sound from the System,
install all speakers except the
subwoofer at the same distance
from the listening position. See
the typical installation next.
If your speakers cannot be
•
installed at the same distance
from the listening position, you
can adjust the speaker distance
of each speaker by remote
control. See “Adjusting the speaker distance” below.
Installing on the wall
You can install the center unit and surround speakers* on the wall.
Ex.: center unit
Wall
A: Minimum 6.5 mm
B: Maximum 10 mm
C: Maximum 6 mm
D: φ 4 mm (screw diameter)
Screw (not
supplied)
CAUTION
The center unit weighs approximately 3.5 kg (7.8 lbs) and the surround
•
speakers* weighs approximately 0.6 kg (1.3 lbs) each. Sufficient care must
be taken when installing them on the wall to prevent any accidents caused by
their falling off.
Use screws which are compatible with the strength and material of the pillar or
•
wall to prevent the center unit and surround speakers* from falling off.
Do not install the center unit and surround speakers* onto a plywood or
•
plasterboard wall; otherwise, they will fall and sustain damage.
When installing the center unit and surround speakers* on the wall;
•
Be sure to have them installed on the wall by qualified personnel.
–
Care must be taken when selecting a location for installation on the wall.
–
Injury to personnel or damage to equipment may result if the installed units
interfere with daily activities.
AC adaptor should not be hanging/put above of any other items. It is
–
acceptable to place the AC adaptor on the flat floor only.
Recommended mounting surface: Wooden studs. If the mount is to be
–
installed on any surface other than wooden studs, use suitable hardware
(which is commercially available).
TH-BA3 only
*
Attaching speaker stands
You can use the speaker stands (not supplied) for installation.
Use this hole to attach
a speaker stand using
a screw
Connect to RX-THBA3
speaker terminal
Stand
Screw (not
supplied)
NOTE
•
When attaching a speaker stand, refer to the instructions of the speaker stands
you purchased.
•
Refer to the supplied information sheet for wire arrangement and containing
the speaker cords.
CAUTION
•
Do not install the surround speakers in a place where they may interfere with
daily activities. Injury to personnel or damage to equipment may result if the
surround speakers are installed in such a place.
Connecting external components
You can connect analog components to the ANALOG terminal and digital
components to the DIGITAL 1 and DIGITAL 2 terminals.
Rear of the center unit
WhiteRed
Digital optical cord
(not supplied)
Digital
Analog
component
RCA pin plug cord
(not supplied)
components
Connecting the power cord
Connect the supplied AC adaptor to the DC IN jacks on the center unit and
wireless receiver unit. Then connect the supplied AC power cord to the AC
adaptor, and plug it in a wall outlet.
Plug in the power cord of the subwoofer to a wall outlet.
•
Connect the supplied AC adaptor to the DC IN jack on the center unit. Then
connect the supplied AC power cord to the AC adaptor, and plug it in a wall
outlet.
Plug in the power cord of the subwoofer to a wall outlet.
•
CAUTION
Disconnect the power cords before cleaning or moving the speakers.
•
Using the core filter
Attach the provided core filter to the power cord and the external components
cord to reduce interference.
1 Release the stopper of the
core filter.
Stopper
2 Run the cable through the core filter, and wind the cable
firmly once inside the cutout of the core filter as shown in the
illustration.
Power cord
External
components
cords*
*
You can wind 2 external components cords together.
3 Close the core filter until it clicks shut.
CAUTION
•
Do not damage the cord by applying excessive force
when winding.
Setting up the subwoofer and
wireless receiver unit*
This System is equipped with a wireless subwoofer and receiver unit*. When
you use them for the first time, activate the wireless pairing.
Refer to the supplied information sheet—“Activate wireless pairing.”
TH-BA3 only
*
NOTE
The wireless pairing is not canceled even after the AC plug has been pulled out.
•
: Only for TH-BA3 / : Only for TH-BA1
— INPUT —
DIGITAL1DIGITAL
ANALOG
MUTING
SPEAKER LEVEL
ch
SPEAKER DISTANCE
ch
SURROUND
MODE
OFF
RM-STHBA3A
2
VOLUME
FADE
DIMMER
TEST
TONE
DRC
TH-BA3 TH-BA1
— INPUT —
DIGITAL1DIGITAL
ANALOG
—
SPEAKER LEVEL —
1
SURROUND
MODE
2
2
FADE
MUTING
OFF
RM-STHBA1A
VOLUME
SURROUNDCENTERSUBWOOFER
DIMMER
DRC
Basic operation
Turning on/off the power
Press .
You can also use the power button on the front panel.
•
NOTE
A small amount of power is consumed even when the power is turned off
•
(standby mode). During standby mode, the STANDBY lamp on the front panel
lights up. Unplug the power cord from the AC outlet to turn the power off
completely.
You can also turn on the System by pressing one of the input buttons (DIGITAL
•
1, DIGITAL 2 or ANALOG).
Selecting the input source
Press one of the input buttons: DIGITAL 1, DIGITAL 2 or ANALOG.
D1 (DIGITAL 1), D2 (DIGITAL 2) or AN (ANALOG) appears on the display for 2
seconds.
You can also use the input button on the front panel.
•
NOTE
The indicator lamp of the selected input source lights.
•
Adjusting the volume
Press VOLUME +/– (0 to 40).
You can also use the volume buttons on the front panel.
•
CAUTION
Set the volume to the minimum level before starting any input source. If the
•
volume is set to a high level, the sudden blast of sound may damage your
hearing and blow out the speakers.
Turning off the sound temporarily
Press FADE MUTING.
To restore the sound, press the button again or adjust the volume.
•
Changing the display brightness
Press DIMMER.
Each time you press the button, the LED brightness changes as follows:
normal \ dim \ off
Making sound clearer (Only for Dolby Digital
and DTS)
You can enjoy low level recorded sound clearly even at a low volume
level—Dynamic Range Compression.
Press DRC.
Each time you press the button, the sound is enhanced the effect as follows:
OF(off) \ MD (middle) \ MX (maximum)
1
The illustration is of TH-BA3.
2 3
4 5 6 7
Buttons and lamps on the front panel
1 (power) button and STANDBY lamp
Turns on/off the System.
STANDBY lamp lights up while the System is turned off.
•
2 Input button and input source indicator lamps
Selects an input source: “DIGITAL 1,” “DIGITAL 2” or “ANALOG.”
The indicator lamp for the selected input source lights up.
•
Adjusting the output level of the
speakers
You can adjust the output level within the range of –6 dB to +6 dB.
1 Press SPK LEVEL ch repeatedly to select the target speaker.
Each time you press the button, the speaker changes as follows:
FL (Front left surround speaker) \ CT (Center speaker) \
FR (Front right surround speaker) \ SR (Surround right speaker)
\ SL (Surround left speaker) \ SW (Subwoofer) \ Back to the
beginning
2 Press SPK LEVEL +/– to adjust the output level while the
indication is displayed.
Press SPK LEVEL +/– for the corresponding speaker.
– SUBWOOFER: Adjusts the output level of the subwoofer.
– CENTER: Adjusts the output level of the center speakers.
– SURROUND: Adjusts the output level of the front surround speakers.
Using the surround mode
You can listen to a more realistic sound than stereo sound using surround.
Available surround modes are as follows:
– SURROUND 1: Suitable for the reproduction of multi-channel sources. S1
– SURROUND 2: Suitable for the reproduction of any stereo music sources.
The indicator lamp of the selected mode lights.
•
Press SURROUND MODE repeatedly to select the desired mode.
The surround mode changes alternately.
To deactivate, press OFF. OF appears on the display.
•
Press SURROUND MODE 1 or SURROUND MODE 2.
To deactivate, press OFF. OF appears on the display.
•
appears on the display when selected.
S2 appears on the display when selected.
TH-BA1’s display is 2 digit.*
3 Surround button and surround indicator lamps
Selects a surround mode: “SURROUND 1,” “SURROUND 2” or SURROUND
OFF.
The indicator lamp for the selected surround mode lights.
•
The DOLBY PROLOGIC II lamp lights up when:
•
surround is activated with an ANALOG input source selected.
–
surround is activated and a DIGITAL input source with 2 channel audio
–
format.
4 Remote sensor
Receives the signal from the remote control.
Adjusting the speaker distance
By adjusting the speaker distance, you can enjoy the optimum surround sound
even if it is hard to install the speakers as shown in the typical installation
above.
1 Press DISTANCE ch repeatedly to select the desired speaker.
The speaker channel has been changed in the following sequence:
FT (Front speaker) \ SL (Surround left speaker) \ SR (Surround
right speaker) \ SW (Subwoofer) \Back to the beginning
2 Press DISTANCE +/– to adjust the distance from the listening
position to the selected speaker.
•
For the example below, set the speaker distance as follows:
Subwoofer (SW)
Center unit (FT)
2.4 m (8 ft)
Surround speaker (SL)
2.7 m (9 ft)
•
You can adjust the speaker distance from 0.3 m to 9.0 m. Each time you press
the button, the distance changes by 0.3 m.
Listening to the test tone
Press TEST TONE to monitor the test tone.
The test tone comes out of the speakers in the following sequence:
FL (Front left surround speaker) \ CT (Center speaker) \ FR (Front
right surround speaker) \ SR (Surround right speaker) \
SL (Surround left speaker) \ Back to the beginning
No test tone comes out of the subwoofer.
•
Press SPK LEVEL +/– to adjust the output level while monitoring the test
tone of these speakers.
•
To stop monitoring the test tone, press TEST TONE.
3.0 m (10 ft)
3.0 m (10 ft)
2.7 m (9 ft)
2.4 m (8 ft)
2.1 m (7 ft)
Surround speaker (SR)
2.7 m (9 ft)
5 Digital signal format lamps
Shows the digital signal format of the incoming signal when “DIGITAL 1”
or “DIGITAL 2” is selected as the input source. Each lamp lights when:
– DOLBY DIGITAL: a Dolby Digital signal comes in.
– DTS: a DTS signal comes in.
– PCM: a Linear PCM signal comes in.
6 Display
Shows the volume level, speaker name and output level of each speaker.
Shows the volume level.
7 Volume buttons
Adjusts the volume within the range of 0 to 40.
Troubleshooting
If you have a problem with this System, check this list for a possible solution
before calling for service.
POWER
Power does not come on.
=
The power cord is not inserted securely. Plug it in securely.
REMOTE CONTROL
The remote control does not work.
=
The battery is exhausted. Replace the battery.
=
Sunlight is shining directly on the remote sensor. Hide the remote sensor
from direct sunlight.
=
The path between the remote control and the remote sensor on the front
panel is blocked.
=
Point the remote control at the remote sensor on the front panel.
=
Signals cannot reach the remote sensor. Move closer to the unit.
=
Pull out the insulation sheet.
SOUND
Sounds are sometimes interrupted.
Radio wave connections may be interrupted. Change the location and
=
orientation of the speakers.
No sound from speakers.
The wireless connections have not been activated correctly. Check the
=
connection.
The sound has been turned off temporarily. Press FADE MUTING on the
=
remote control or adjust the volume by pressing VOLUME +/–.
Radio wave reflections
The System is connected directly by radio waves which are reflected by
walls, furniture and buildings. If the System cannot receive the waves
properly, move the System to obtain better reception.
Radio wave reception may also be interrupted by people moving between
the units.
Loading...